Aiwa SX-R275 Operating Instructions Manual

88-N FS-903-11

980311 BMI-U-9

For assistance and information

call toll free l-800-BIJY-AIWA

(United States and Puerto Rico)

tilil??ii

DIGITAL AUDllJ

/L!L.J

DO NOT OPEN

/

e

\

I

“CAUTION:TO REDUCE THE RISK OF

TRIC SHOCK,

I

DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED

Owner’s record

For your convenience, record the model number and serial

number (you will find them on the rear of your set) in the space

provided below. Please refer to them when you contact your Aiwa

dealer in case of difficulty.

I Model No. / Serial No. (Lot No.) I

I CX-NMT920

I I

SX-NA902

SX-R275

Read the Operating Instructions carefully and completely before

operating the unit. Be sure to keep the Operating Instructions

for future reference. All warnings and cautions in the Operating

Instructions and on the unit should be strictly followed, as well

as the safety suggestions below.

Installation

1

2

3

4

5

6

7

8

Water and moisture — Do not use this unit near water, such

as near a bathtub, washbowl, swimming pool, or the like.

Heat — Do not use this unit near sources of heat, including

heating vents, stoves, or other appliances that generate heat.

It also should not be placed in temperatures less than 5°C

(41 ‘F) or greater than 35°C (95°F).

Mounting surface — Place the unit on a flat, even surface.

Ventilation — The unit should be situated with adequate

space around it so that proper heat ventilation is assured.

Allow 10 cm (4 in.) clearance from the rear and the top of the

unit, and 5 cm (2 in.) from each side.

- Do not place the unit on a bed, rug, or similar surface that

may block the ventilation openings.

- Do not install the unit in a bookcase, cabinet, or airtight rack

where ventilation may be impeded.

Objects and liquid entry — Take care that objects or liquids

do not get inside the unit through the ventilation openings.

Carts and stands — When placed

or mounted on a stand or cart, the

unit should be moved with care.

Quick stops, excessive force, and

@!!l

●\

uneven surfaces may cause the

3

AA*

unit or cart to overturn or fall.

Condensation — Moisture may form on the CD pickup lens

when:

- The unit is moved from a cold spot to a warm spot

- The heating system has just been turned on

- The unit is used in a very humid room

- The unit is cooled by an air conditioner

When this unit has condensation inside, it may not function

normally. Should this occur, leave the unit for a few hours,

then try to operate again.

Wall or ceiling mounting — The unit should not be mounted

on a wall or ceiling, unless specified in the Operating

Instructions.

Electric Power

1 Power sources —

Connect this unit only to power sources

specified in the Operating Instructions, and as marked on the

unit.

2

Polarization —As a safety feature, some units are equipped

with polarized AC power plugs which can only be inserted

one way into a. power outlet. If it is difficult or impossible to

insert the AC power plug into an outlet, turn the plug over and

try again. If it still does not easily insert into the outlet, please

call a qualified service technician to service or replace the

outlet, To avoid defeating the safety feature of the polarized

plug, do not force it into a power outlet,

3

AC power cord

- When

disconnecting the AC power cord, pull it out by the

AC power plug. Do not pull the cord itself.

- Never handle the AC power plug with wet hands, as this

could result in fire or shock.

- Power cords should be firmly secured to avoid being severely

bent, pinched, or walked upon. Pay particular attention to

the cord from the unit to the power outlet.

- Avoid overloading AC power plugs and extension cords

beyond their capacity, as this could result in fire or shock.

\ SX-C605

I I

I ENGL/SH

4

5

Extension cord —To help prevent electric shock, do not use

a polarized AC power plug with an extension cord, receptacle,

or other outlet unless the polarized plug can be completely

inserted to prevent exposure of the blades of the plug.

When not in use— Unplug the AC power cord from the power

outlet if the unit will not be used for several months or more.

When the cord is plugged in, a small amount of current

continues to flow to the unit, even when the power is turned

off

Outdoor Antenna

1

2

Power lines —

When connecting an outdoor antenna, make

sure it is located away from power lines.

Outdoor antenna grounding — Be sure the antenna system

is properly grounded to provide protection against unexpected

voltage surges or static electricity build-up. Article 810 of the

National Electrical Code, ANSI/NFPA 70, provides information

on proper grounding of the mast, supporting structure, and

the lead-in wire to the antenna discharge unit, as well as the

size of the grounding unit, connection to grounding terminals,

and requirements for grounding terminals themselves.

Antenna Grounding According to the National Electrical Code

n

~ ANTENNA LEAD IN WIRE

. ANTENNA DISCHARGE UNIT

(NEC SECTION 8<O-20)

ELECTRIC

SERVICE

EQUIPMENT

GROUNDING CONDUCTORS

(NEC SECTION 810-21)

GROUND CLAMPS

, ~ POWER SERVICE GROUNDING

ELECTRODE SYSTEM

(NEC ART 250 PART H)

NEC-NATIONAL ELECTRICAL CODE

Maintenance

Clean the unit only as recommended in the Operating

Instructions.

Damacre Reauirina Service

Have the units serviced by a qualified service technician if:

- The AC power cord or plug has been damaged

- Foreign objects or liquid have gotten inside the unit

- The unit has been exposed to rain or water

- The unit does not seem to operate normally

- The unit exhibits a marked change in performance

- The unit has been dropped, or the cabinet has been damaged

DO NOT ATTEMPT TO SERVICE THE UNIT YOURSELF.

PRECAUTIONS .................m.................................................1

PREPARATIONS

SETTING UP .......................................................................3

REMOTE CONTROL ............................................................5

BEFORE Operation .........................................................6

SOUND

AUDIO ADJUSTMENTS ................................................... 7

RHYTHM PLAY FUNCTION (BEAT MASTER) .................7’

GRAPHIC EQUALIZER ......................................................8

DSP SURROUND .......................................................m.... lUI

RADIO RECEPTION

MANUAL TUNING ............................................................. 11

PRESETTING STATIONS ................................................ 12

TAPE PLAYBACK

BASIC OPERATIONS ...................................................... 13

CONTINUOUS PLAY ....................................................... 14

CD PLAYING

BASIC OPERATIONS ...................................................... 15

PROGRAMMED PLAY ..................................................... 16

RECORDING

BASIC RECORDING ........................................................ 17’

DUBBING A TAPE MANUALLY ...................................... 18

DUBBING THE WHOLE TAPE ........................................ 18

❑

Al EDIT RECORDING ........................s............................. 19

PROGRAMMED EDIT RECORDING ............................... 20

DOLBY PRO LOGIC

ADJUSTING SPEAKER LEVEL BALANCE ...................21

PLAY WITH DOLBY PRO LOGIC ................................... 22

KARAOKE

MICROPHONE MIXING ................................................... 23 -

KARAOKE PROGRAM .................................................... 24

CLOCK AND TIMER

SETTING THE CLOCK .................................................... 25

SETTING THE SLEEP TIMER ......................................... 25

SETTING THE TIMER ...................................................... 26

OTHER CONNECTIONS

CONNECTING OPTIONAL EQUIPMENT ....................... 27

LISTENING TO EXTERNAL SOURCES ......................... 27

CONNECTING A DVD PLAYER ...................................... 28I

GENERAL

CARE AND MAINTENANCE ........................................... 291

TROUBLESHOOTING GUIDE ......................................... 2$1

SPECIFICATIONS ............................................................ 301

PARTS INDEX ...................................................

Back cover

ENGLISH 2

The DOLBY PRO LOGIC system which is the biggest feature of

this stereo system provides you with multi channel sound in your

home.

Complete setting and connection of the main unit, supplied

speakers, your TV and video equipment according to the following

procedure.

Check your system and accessories

@

o

@

@ CX-NMT920 Compact disc stereo cassette receiver

@ SX-NA902 Front speakers

SX-R275

SX-C605

Surround speakers

Center speaker

Remote control

AM antenna

FM antenna

Operating instructions, etc.

..*.e,....$. ,*. ,/ ,* .,. ,,. ~, ,, ~., ., . .. ,,. . . < J ....>. ~. .. ,: *, ..,. . . . ,+, . . .

. . . >.. , ,., . . ,,. ,. . ,+. ,. ~ ., ,* : ., .; . .. .....< .,

,x . ., .<

POSITIONING THE SPEAKERS

To achieve the optimum effects obtainable with the DOLBY PRO

LOGIC system, it is important to position the speakers properly.

Refer to the following illustration to find out the best location in

your room.

1=

@ Front speakers

@ Center speaker

Position in the center of the two front speakers. In addition,

position on or below the TV set, if connecting a TV set to the

unit.

@

Surround speakers

Place the surround speakers directly to the side of or slightly

behind the listening area. Align them horizontally, about 1

meter (3.2 feet) above ear height.

m

● No sound is heard from the center and surround speakers when

the DOLBY PRO LOGIC, the SURROUND system and the 5.1

CH (page 28) are set to off.

● The center speaker sounds when the DOLBY PRO LOGIC or

the 5.1 CH (page 28) is set to on.

CONNECTIONS

Before connecting the AC cord

The rated voltage of your unit shown on the rear panel is

120 V AC. Check that the rated voltage matches your local

voltage.

IMPORTANT

Connect the speakers, antennas, and all optional equipment first,

Then connect the AC cord in the end.

3 ENGLISH

.-

Speaker cord

k

AC cord

+7

1 Connect the supplied antennas.

3 Connect thesurround speakers.

Connect the FM antenna to FM 75 Q terminals and the AM

Connect the surround speaker cords to

SURROUNDI

antenna to AM LOOP terminal.

SPEAKERS terminals.

There is no difference between the surround speakers. Boti+

m

speakers can be connected as R (right) or L (left).

Q

@@: . . .

0 Y*

; .,:..

f-

●

‘(t

.

‘!s

J.J ,,;<p,

, j;,, .,-.,

.

..:,.,,

it??;,,,

4 Connect the center speaker.

Connect the center speaker cord to CENTER SPEAKER

terminal.

-:,,

;, ,..

~ (,3,‘

.?’.

,t-<-),

F<*

\,,

h,

. .

.

2

Connect the front speakers.

The speaker placed on the right side of the unit facing you is

5

Connect the video equipment.

“the right speaker” and another one is “the left speaker”.

Connect

VIDEO/AUX jack of this unit to the audio output jack

of the video equipment with an optional audio connecting cord.

#

@

6 Connect the Television to the video equipment.

Refer to the Operating Instructions of the connecteci

@

H

equipment for details.

.

.’

“

o

7 Connect the AC cord to an AC outlet.

The cords with white stripes should be connected to ~

terminals and the other cords to O terminals.

ENGLISH41

To position the antennas

FM feeder antenna:

Extend this antenna horizontally in a T-shape and fix its ends to

the wall.

AM antenna:

Position to find the best possible reception.

To stand the AM antenna on a surface

Fix the claw to the slot.

To mount the surround speakers on the wall

Mount each speaker on a spot that can hold its weiaht.

m

● Be sure to connect the speaker cords correctly. Improper

connections can cause short circuits in SPEAKERS terminals.

● Do not leave objects generating magnetism, such as credit

cards, near the speakers, as these objects may be damaged.

● Do not bring the FM antenna near metal objects or curtain rails.

● Do not bring the AM antenna near other optional equipment,

the stereo system itself, the AC cord or speaker cords, since

noise will be picked up.

● Do not unwind the AM antenna wire.

For better FM reception, use of an outdoor antenna is

recommended.

Connect the outdoor antenna to FM 75 Q terminals,

To connect other optional equipment + page 27 and

28.

Inserting batteries

Detach the battery cover on the rear of the remote control and

insert two R6 (size AA) batteries,

R6(’AA)

When to replace the batteries

The maximum operational distance between the remote control

and the sensor on the main unit should be approximately 5 meters

(16 feet). When this distance decreases, replace the batteries

with new ones.

Using the remote control

The instructions in this manual refer mainly to the buttons on the

main unit. Buttons on the remote control with the same names

as those on the main unit can be used as well.

● If the remote control is not going to be used for an extended

period of time, remove the batteries to prevent possible

electrolyte leakage.

● The remote control may not operate correctly when:

- The line of sight between the remote control and the remote

sensor inside the display window is exposed to intense light,

such as direct sunlight

- Other remote controls are used nearby (those of a television,

etc.)

5 ENGLISH

! .—...

Is

Game Demo

When the AC cord is connected, the display window demonstrates

the game Demo. When the power is turned on, the game Demo

is overridden by the operation display. When the power is turned

off, the game Demo is restored.

DEMO

CD

To cancel the game Demo

Press DEMO. To re-activate the game Demo, press DEMO

again.

To turn the power on

Press one of the function buttons (TAPE, TUNER, VIDEO/AUX,

CD, MD).

Playback of the inserted disc or tape begins, or the

previously tuned station is received (Direct Play Function),

POWER is also available.

When the unit is turned on, the disc compartment may open and

close to reset the unit.

To turn the power off

Press POWER.

Flash windows

The windows on the top of the unit and the cassette decks light

up or flash while the unit is being powered on.

To turn off the light of the top window, press

■ while pressing

CD. To turn back on, repeat the above.

The light of the cassette decks cannot be turned off.

To dim the illumination of the display

1

Press DISPLAY twice so that “DIMMER is displayed,

2 Within 4 seconds, turn

MULTI JOG to select the dimmer mode

as follows.

~DIMMERO ++ DIMMER 1 ~Dl MM ER2+--+Dl MMER 3

7

I

DIMMER 0: The normal display.

DIMMER 1: The illumination of the display is dimmer than

usual,

DIMMER 2: The illumination of the display is dimmer than

DIMMER 1.

DIMMER 3: The illumination of the display is dimmer than

DIMMER 2, and the spectrum analyzer and the illumination

on the buttons light off,

To play the game Demo

1

Press DEMO so that the game Demo displays.

2 Press +>.

Three numbers on the display start to run.

3 Press ❑ once,

The number on the left side stops,

4 Press 9 twice to stop the remaining two numbers.

● You can enjoy the game Demo with game sound by pressing

DEMO while the power is on.

Scoring:

20 points are given to start the game.

If all the numbers are eaual, 50 points are added to the score,

If not eaual, one point is subtracted.

If the gained points reach 9999, you win.

If the gained points fall to O, you lose.

To reset the game Demo

Press DEMO twice, then press <~. The game starts again.

To mute the game sound

Once, cancel the game Demo by pressing DEMO. Then, keep

pressing DEMO until “~~ OFF” is displayed.

To restore the game sound, keep pressing

DEMO again until

“)) ON” is displayed.

m

● During playing the game Demo, W and <> are available only

for the game Demo. Cancel the game Demo to use these

buttons for the functions such as CD playing, etc.

● To change the game sound, see “RHYTHM PLAY FUNC1-ION’”

on page 7.

● During the game Demo, some indicators unrelated with the

actual operation light up on the display.

To change the spectrum analyzer display

3

patterns of spectrum analyzer display can be shown.

Press

DISPLAY once, and turn MULTI JOG within 4 seconds to

select the desired spectrum analyzer display.

ENGLISH 6

Turn VOLUME on the main unit, or press VOLUME on the

remote control.

The volume level is displayed as a number from Oto MAX (50).

The volume level is automatically set to 20 when the power is

turned off with the volume level set to 21 or more.

To change the Ieft/right balance

Press MANUAL SELECT on the remote control. UR is displayed

for 2 seconds. Press 1+

DOWN or W UP on the remote

control within these 2 seconds.

c The DOLBY PRO LOGIC (page 21) and the DOLBY DIGITAL

SURROUND (page 28) front speakers level is also changed.

BBE SYSTEM

The BBE system enhances the clarity of high-frequency sound.

It also enriches the Karaoke function to make your voice sound

clear and pleasant.

Press BBE.

Each time it is pressed, the level changes. Select one of the

three levels, or the off position to suit your preference.

● The BBE system does not perform while the 5.1 CH (page 28)

is selected,

The T-BASS system enhances the realism of low-frequency

sound.

Press T-BASS.

Each time it is pressed, the level changes. Select one of the

three levels, or the off position to suit your preference.

m

You can enjoy music of CDs, tapes or etc. mixed with rhythm

patterns programmed in the unit.

7 Press RHYTHM.

One of the rhythm patterns is displayed.

2 Turn MULTI JOG to select the desired rhythm

pattern.

The rhythm pattern is displayed cyclically as follows.

‘AM/-----l

Waltz 1,2,3

H.Rock 1,2,3

[

(Hard Rock)

1

4 Beat 1,2,3

Samba 1,2,3

! 1

8 Beat 1,2,3 Salsa 1,2,3

1

I

16 Beat 1,2,3++

Mereng 1,2,3

(Merengue)

To change the tempo of the selected rhythm pattern

Press RHYTHM ~ while the selected rhythm pattern is

displayed, then turn MULTI JOG to select the rhythm tempo,

The rhythm tempo can be changed from 90 to 160.

Low frequency sound may be distorted when the T-BASS system

is used for a disc or tape in which low frequency sound is originally

emphasized. In this case, cancel the T-BASS system.

7 ENGLISH

To change the volume level of the selected rhythm pattern

Press RHYTHM w while the selected rhythm pattern is

displayed, then turn MULTI JOG to select the volume level,

The volume level can be changed from 1 to 4.

To cancel the rhythm play function

Press MULTI JOG.

To restart the rhythm play function

Press MULTI JOG again. The rhythm pattern selected last time

starts.

● When the GAME pattern is selected, the rhythm tempo and

the rhythm volume level cannot be changed.

● The signal output from LINE OUT jack is affected with the

rhythm play function.

These voice wave data incorporated in this product are Yamaha

Corporation’s copyrightable property and we are licensed by

Yamaha Corporation.

... ... ....,., ,+..,,, .+,,

...../.,

SELECTiNG THE PROGRAMMED

EQUALIZATION CURVE

This unit provides the following 5 different programmed

equalization curves.

ROCK: Powerful sound emphasizing treble and bass

POP: More presence in the vocals and midrange

JAZZ: Accented lower frequencies for jazz-type music

CLASSIC: Enriched sound with heavy bass and fine treble.

LATIN: Accented higher frequencies for Iatin music.

GEQ

“i–+ u

Press GEQ, and turn MULTI JOG to select one of the

programmed equalization curve within 4 seconds.

“GRAPHIC EQUALIZER lights up

“GRAPHIC EQUALIZER appears (except “GEQ OFF”) and the

GEQ mode is displayed cyclically as follows.

c

ROCK- POP~JAZZ~CLASSIC~ LATIN “

~---------- Progra:med mode ----------:

GEQOFF— M4— M3— M2—

Ml+

1

(cancel) ~______~anual mode _____~

To display the current GEQ mode

Press GEQ. The current mode is displayed for 4 seconds.

To cancel the selected mode

Press GEQ, and turn MULTI JOG to select” GEQ OFF” within 4

seconds. “GRAPHIC EQUALIZER disappears.

Using the headphones

Connect headphones to the PHONES jack with a standard stereo

plug (~6.3 mm,

‘/4 inch).

No sound is output from the speakers while the headphones are

plugged in.

● When the headphones are plugged in, the SURROUND system,

the DOLBY PRO LOGIC and the 5,1 CH (page 28) do not

function.

Sound adjustment during recording

The output volume and tone (except BBE and Rhythm play

function) of the speakers or headphones may be freely varied

without affecting the recording.

——. .............................

.—. ..—\

u

$

?

The equalization curve can be customized to suit your preference.

1

2

3

4

Up to 4 customized equalization curves can be stored as the

manual modes Ml - M4.

1 Set a new equalization curve with HIGH, LOW,

and MULTI JOG.

See “SETTING ANEW EQUALIZATION CURVE MANUALLY”.

The created curve is displayed for 4 seconds.

2 Within 4 seconds, press ENTER.

“M 1“ flashes on the display for 4 seconds.

3

4

To select the stored equalization curve

Press GEQ, and turn MULTI JOG to select one of the manual

modes Ml - M4 within 4 seconds.

● If this step is not completed within 4 seconds, press GEQ

first to display “GE(2 ON”. Then press ENTER within 4

seconds.

Within 4 seconds, turn MULTI JOG to select one

of the manual modes Ml - M4 to store the curve.

Within 4 seconds, press ENTER.

The new equalization curve is stored.

9 ENGLISH

SETTING A NEW DSP SURROUND SO[JN13

MANUALLY

The DSP (Digital Signal Processor) SURROUND adjusts the

delay time, the input mode and the feedback level to give a

resonant surround sound, allowing you to enjoy the real sound

presence of different environments.

This unit has been programmed with 4 different SURROUND

modes. You can also create and memorize up to 4 of your own

surround settings.

SELECTING A PROGRAMMED DSP

SURROUND MODE

MULTI

JOG

When you select the programmed DSP SURROUND mode, the

sound presence of a disco (DISCO), live music performance

(LIVE), movie theater (MOVIE) or concert hall (HALL) can be

obtained.

Press SURROUND, and turn MULTI JOG to select

the desired Programmed mode within 4 seconds.

“DSP SURROUND” appears and the DSP SURROUND mode is

displayed cyclically as follows.

c

DISCO —

LIVE — MOVIE — HALL

‘---------- Programmed mode ----------:

DSP OFF — M4 + —

— Ml

J

(cancel) ~_----- M~nua, m~fe ----- j

Equalization curves are selected automatically to match the DSP

SURROUND modes and can also be selected or turned off to

suit your preference.

To display the current DSP SURROUND mode

Press SURROUND. The current mode is displayed for 4 seconds.

To cancel the selected mode

Press SURROUND, and turn MULTI JOG to select “DSP OFF

within 4 seconds. “DSP SURROUND” disappears.

The elements of the DSP SURROUND sound can be customized.

DELAY (delay time)

Increasing the number in the display increases the delay time

and surround effect. “15“, “ 20”, “30” or “50” mSec can be

selected.

To adjust the delay time

Press DELAY, and turn MULTI JOG to select one of the levels

within 4 seconds.

L-R, L+R (inDut mode)

When “L+R” is displayed, the surround effect increases,

especially in the center.

When “L-R is displayed, it increases on the outside.

To select a input mode

Press EFFECT ~, and turn MULTI JOG to select “L-R” or

“L+R” within 4 seconds.

FB (feedback level}

Increasing the number in the display increases the echo.

A level from “OFF (0) to “7” can be selected.

To adjust the level of feedback

Press EFFECT M, and turn MULTI JOG to select one of

the levels within 4 seconds.

When the music source is monaural

Select “LIVE” or “MOVIE” to obtain a simulated stereo effect.

When “DISCO or “HALL” is selected, no sound will be heard

from the surround speakers.

ENGLISH

1()

Up to 4 DSP SURROUND sound can be memorized as the

manual modes Ml - M4.

1

2

3

4

Set a new DSP SURROUND sound with DELAY,

EFFECT, and MULTI JOG.

See

“SETTING A NEW DSP SURROUND SOUND

MANUALLY”.

Within 4 seconds, press ENTER.

“Ml” flashes on the display.

● If this step is not completed within 4 seconds, press

SURROUND first to display “DSP ON”. Then press ENTER

within 4 seconds.

Within 4 seconds, turn MULTI JOG to select one

of the manual modes Ml - M4.

Within 4 seconds, press ENTER.

The new DSP SURROUND sound is memorized

To select the stored DSP SURROUND sound

Press SURROUND, and turn MULTI JOG to select one of the

manual modes Ml - M4 within 4 seconds.

To adjust the volume of the surround speakers

Press MANUAL SELECT twice or three times on the remote

control.

“S-L” or “S-R is displayed for 2 seconds. Press ~ DOWN or

>1 UP on the remote control within these 2 seconds.

● The DOLBY PRO LOGIC (page 21) and the DOLBY DIGITAL

SURROUND (page 28) surround speakers level is also changed.

m

— MONO

1 Press TUNER/BAND repeatedly to select the

desired band.

r-

FM— AM

2

When TUNER/BAND is pressed while the power is off, the

power is turned on directly.

Press ++ DOWN or ~ UP to select a station.

Each time the button is pressed, the frequency changes.

When a station is received, “TUNE is displayed for 2 seconds.

During FM stereo reception, ([loll) is displayed.

To search for a station quickly (Auto Search)

Keep - DOWN or - UP pressed until the frequency starts

to change rapidly. After tuning in to a station, the search stops.

To stop the Auto Search manually, press e DOWN or -

UP.

● The Auto Search may not stop at stations with very weak

signals.

When an FM TUNER stereo broadcast contains noise

Press MONO TUNER on the remote control so that “MONO”

appears on the display.

Noise is reduced, although reception is monaural.

To restore stereo reception, press

MONO so that “MONO”

disappears.

The SURROUND mode is canceled when:

- the ECHO level is changed.

- the DOLBY PRO LOGIC is turned on.

- the headphones are plugged in.

- the 5.1 CH (page 28) is selected.

I 1 ENGLISH

DIRECTION/

PRESET

The unit can store a total of 32 preset stations, When a station is

stored, a preset number is assigned to the station. Use the preset

number to tune in to a preset station directly.

1 Press TUNER BAND to select a band, and press

- DOWN or F> UP to select a station.

2 Press 11 SET to store the station.

A preset number beginning from 1 in consecutive order for

each band is assigned to the station,

Frequency Preset number

I 1

>2 ..,../

PRESET NUMBER ”TUN”ING<‘‘‘“

z

o

Use the remote control to select the preset number directly.

‘E

1 Press BAND to select a band.

‘~9 ‘

j~:

flu.

2 Press numbered buttons O-9 and +1Oto sele!ct a ~%:

preset number.

g:.

,*:

Example:

*

To select preset number 20, press +10, +10 and O.

4

u

To select preset number 15, press +10 and 5.

Selecting a preset number on the main unit

Press TUNER BAND to select a band. Then, press +>

DIRECTION/PRESET repeatedly or turn MULTI JOG,

Each time <~ DIRECTION/PRESET is pressed, the nexl

ascending number is selected,

To clear a preset station

Select the preset number of the station to be cleared. Then, press

■ CLEAR, and press II SET within 4 seconds,

The preset numbers of all other stations in the band with higher

numbers are also decreased by one.

3 Repeat steps 1 and 2.

The next station will not be stored if a total of 32 preset stations

for all the bands have already been stored.

To change the AM tuning interval

The default setting of the AM tuning interval is 10 kHz/step. If

you use this unit in an area where the frequency allocation system

is 9 kHz/step, change the tuning interval.

Press

POWER while pressing TUNER BAND.

To reset the interval, repeat this procedure.

m

When the AM tuning interval is changed, all preset stations ar(s

cleared. The preset stations have to be set again.

ENGLISH

12

,,

......

Deck 2

● On deck 1, tapes are always played back on both sides.

On deck 2, you can select a reverse mode to play back one or

both sides,

● Use Type I (normal), Type II (high/CrOz) or Type IV (metal)

tapes for playback.

Press TAPE and press A EJECT to open the

cassette holder.

A EJECT

Insert a tape with the exposed side down. Push the cassette

holder to close.

To select a reverse mode (deck 2 only)

Each time REV MODE is pressed, the reverse mode changes.

To play one side only, select =.

To play from front side to reverse side once only, select =>.

To play both sides repeatedly, select (=).

● When tapes are loaded in both decks, Z) on the display

indicates Continuous Play,

.

Insert a tape.

7 Press DOLBY NR and turn Dolby NR on or off to

match the playback tape.

For tapes recorded with DOLBY NR, turn on Iln NR.

For tapes recorded without DOLBY NR, turn off UU NR.

2 Press 4 ➤ to start play.

Playing deck number

Playback side indicator The tape counter indicates the

tape running length.

E: The front side is being played (forward).

<: The back side is being played (reverse).

When tapes are loaded in both decks

Press TAPE first to select a deck.

The selected deck number is displayed.

To stop play, press ■ .

To pause play (deck 2 only),

press II. To resume play, press

again.

To change the playback side, press< ➤ DIRECTION/PRESET

in play or pause mode.

To fast forward or rewind, press - or -, Then press

■ to

stop the tape.

Tostart play when the power is off (Direct Play Function)

Press TAPE. The power is turned on and play of the inserted

tape begins.

To set the tape counter to 0000

Press I CLEAR in stop mode,

The counter is also set to 0000 when the cassette holder is

opened and closed.

13 ENGLISH

If there is a 4-second or longer blank between each track, a

search for the beginning of the current or next track during

playback can be done easily,

Press + or * during playback referring to the playback side

indicator (4 or b) on the display.

For example, when > is pressed while > is displayed,

playback of the next track starts.

Music sensor function may not be able to detect tracks under

the following conditions:

● Blanks of less than 4 seconds between tracks

● Noisy blanks

● Long passages of low-end sound

● Low overall recording levels

,-

-.

~

, ,

; ,,

,7

$

.-fi ......

__,..

.-..)

After playback on one deck finishes, the tape in the other deck

will start to play without interruption.

1

2

3

4

Insert tapes into deck 1 and deck 2.

Press TAPE DECK1/2 to select the deck to be

played back first.

Press REV MODE to select Z).

Press -4 ➤ to start playback.

Playback continues until ■ is pressed.

About cassette tapes

● To prevent accidental erasure, break off the plastic tabs

on the cassette tape after recording with a screwdriver or

other pointed tool.

Side A

a

<q

\ :03

‘“”i * 1

Type

II tape

Tab for side A

detection

slot

To record on the tape again, cover the tab openings with

adhesive tape, etc. (On Type

II tapes, take care not to

cover the Type

II tape detection slot.)

● 120-minute or longer tapes are extremely thin and easily

deformed or damaged. They are not recommended.

● Take up any slack in the tape with a pencil or similar “tool

before use. Slack tape may break or jam in the mechanism.

DOLBY NR system

The Dolby Noise Reduction system reduces tape hiss noise.

For optimum performance when playing back a tape

recorded with the DOLBY NR system, turn on the DOLBY

NR system.

DISC CHANGE

DISC DIRECT PLAY 1-3

)

DISC

DIRECT PLAY

I ._ ~RANDOMl

[i- .!+ ““”

1

—!...J:il IIQ CJ G c

-II@!MULTI !

JOG

CD EDIT

CHECK

“1

II

! !“”

/.. :.

, .............

¤~

-$

/

%

;:

u

[~~

‘“

4>

Press CD, then press A OPEN/CLOSE to open the

disc compartment. Load disc(s) with the label side

up.

To ~Iav one or two discs, place the discs on tray 1 and 2.

To plav three

discs, press DISC CHANGE to rotate the trays

after placing two discs. Place the third disc on tray 3,

Close the disc compartment by pressing A OPEN/CLOSE.

Tray 1

CHANGE

Tray number of the

disc to be played

Total playing time

Total number of tracks

Load discs.

To play all discs in the disc compartment, press ● >.

Play begins with the disc on tray 1.

Number of track being played

Elapsed playing time

To play one disc only press DISC DIRECT PLAY 1-3.

The selected disc is played once,

To play with the remote control

Press

DISC DIRECT PLAY, then press numbered buttons 1-3

within 3 seconds to select a disc.

To stop play, press

■ .

To pause play, press II. To resume play, press again.

To search for a particular point during playback, keep ~

or > pressed and release it at the desired point.

To skip to the beginning of a track during playback, press

- or - repeatedly or turn MULTI JOG.

To remove

discs, press = OPEN/CLOSE,

To start play when the power is off (Direct Play Function)

Press CD. The power is turned on and play of the loaded disc(s)

begins.

When A OPEN/CLOSE is pressed, the power is also turned on

and the disc compartment is opened.

To

check the remaining time

During play, press CD EDIT/CHECK. The amount of time

remaining until all tracks finish playing is displayed. To restore

the playing time display, repeat the above.

Selecting a track with the remote control

1

2

Press

DISC DIRECT PLAY, then press numbered buttons

1-3within 3 seconds to select a disc,

Press numbered buttons O-9 and

+1Oto select a track.

Example:

To select the 25th track, press +10, +10 and 5.

To select the 10th track, press

+1Oand O.

The selected track starts to play and continues to the end of

that disc.

Replacing discs during play

While one disc is playing, the other discs can be replaced without

interrupting play.

1 Press DISC CHANGE.

2

Remove the discs and replace with other discs.

3 Press A OPEN/CLOSE to close the disc compartment.

m

● When loading an 8-cm (3-inch) disc, put it onto the inner circle

of the tray.

● Do not place more than one compact disc on one disc tray.

● Do not tilt the unit with discs loaded. Doing so may cause

malfunctions,

● Do not use irregular shape CDs (example: heart-shaped,

octagonal ones). It may result in malfunctions,

15 ENGLISH

Use the remote control.

RANDOM play

All the tracks on the selected disc or all the discs can be played

randomly.

REPEAT play

A single disc or all the discs can be played repeatedly.

Press RANDOM/REPEAT.

Each time it is pressed, the function can be selected cyclically.

RANDOM play — RANDOM lights up on the display.

REPEAT play — % lights up on the display.

RANDOM/REPEAT play — RANDOM and % light up on the

display,

Cancel — RANDOM and G disappear from the display.

To rNav all discs, press - to start play.

To Plav a sincrle disc, press one of DISC DIRECT PLAY 1-3 to

start play.

During random play it is not possible to skip to the previously

played track with -.

Up to 30 tracks can be programmed from any of the inserted

discs.

1

2,3

Use the remote control.

1 Press PRGM twice in stop mode.

!’ ---..,> .— ., ..-,- -.,

‘rtr~wl IS alspiayea

PRGM

2

● When the PRGM is pressed once in step 1, the unit enters

the KARAOKE PROGRAM (page 24).

Press DISC DIRECT PLAY, then press numbered

buttons 1-3 within 3 seconds to select a disc.

Go to the next step when the tray stops rotating.

3

4

5

Press numbered buttons O-9 and +10 to program

a track.

:E’

Example:

;g:

To select the 25th track, press

+10, +10 and 5.

:s:

To select the 10th track, press

+10 and 0.

;il;

Selected track number

Program number

Total number of

!@

Q

selected tracks

Total playing time of

the selected tracks

Repeat steps 2 and 3 to program other traclks.

Press 4P to start play.

To check the program

Each time ++ or * is pressed in stop mode, a disc number,

track number, and program number will be displayed.

To clear the program

Press 9 CLEAR in stop mode

To add tracks to the program

Repeat steps 2 and 3 in stop mode. The track will be programmed

after the last track.

To change the programmed tracks

Clear the program and repeat all the steps again.

To play the programmed tracks repeatedly

After programming the tracks, press RANDOM/REPEAT

repeatedly until G appears on the display.

m

During programmed play, you cannot perform random play,

checking the remaining time, and selecting a disc or track.

ENGLISH

16

This section explains how to record from the tuner, CD player, or

external equipment.

u

Deck 2

■

Preparation

c

Use Type I (normal) and Type II (high/CrOz) tapes for recording.

● Set the tape to the point where recording will start.

1

2

3

4

5

Insert the tape to be recorded on into deck 2.

Insert the tape with the side to be recorded on first facing out

from the unit.

A EJECT

Press REV MODE to select the reverse mode.

To record on one side only, select Z.

To record on both sides, select =) or (1).

Press DOLBY

NR to turn Dolby NR on or off.

To record with DOLBY NR, turn on 00 NR.

To record without DOLBY NR, turn off

❑U NR.

Press function (CD, TUNER, VIDEO/AUX

or MD)

and prepare the source to be recorded.

To record from a CD, press CD and load the disc(s).

To record from a radio broadcast, press

TUNER and tune

in to a station.

To

record from a connected source, press VIDEO/AUX or

MD.

Press ● REC/REC MUTE to start recording.

When the selected function is CD, playback and recording

start simultaneously.

To

stop recording, press ■ .

To pause recording, press II. (Applicable when the source is

TUNER, VI DEO/AUX or MD) To resume recording, press it again.

To start recording with the remote control

First press ./0

REC/REC MUTE, and then press+ ➤ within 2

seconds.

Sound adjustment during recording

The output volume and tone (except BBE and Rhythm play

function) of the speakers or headphones may be freely varied

without affecting the recording.

Insertion of 4-second blank spaces enables you to activate the

Music Sensor function. (Applicable when the source is TUNER,

VIDEO/AUX or MD.)

1 Press ● REC/REC MUTE during recording or while in

recording pause mode.

~

on the display flashes for 4 seconds and the tape runs

without recording. After 4 seconds, the deck enters the

recording pause mode.

2

Press 11 to resume recording.

To insert a blank space of less than 4 seconds,

press ●

REC/REC MUTE again while ~ is flashing.

Toinsert blank spaces of more than 4 seconds, after the deck

enters recording pause mode, press . REC/REC MUTE again.

Each time the button is pressed, a 4-second blank space is

added.

To erase a recording

Make sure the microphone is not connected to this unit and the

Rhythm play function (page 7) is canceled.

Set the microphone volume and the echo level to OFF (see page

23).

1 Insert the tape to be erased into deck 2 and press TAPE DECK

112 to display ‘(TP 2.

2 Set the tape to the point where the erasure is to be started.

3 Set the reverse mode by pressing REV MODE.

4 Press

● REC/REC MUTE to start the erasure.

17 ENGLISH

m

c Set the tape to the point where recording will start.

● The reverse mode is automatically set to 1.

Note that recording will be done on one side of the tape only.

1

2

3

4

5

Press TAPE,

Insert the original tape into deck 1 and the tape

to be recorded on into deck 2.

Insert the tapes with the sides to be played back or recorded

on facing out from the unit.

Press

DOLBY NR to turn off the Dolby NR.

❑0

NR on the display goes out,

Press TAPE DECK 1/2 to select deck 1.

“TP 1“ is displayed.

Press @ REC/REC MUTE to start recording.

Playing and recording start simultaneously.

To stop dubbing

Press W.

To set the Dolby NR when playing back the dubbed tape

Press DOLBY NR and turn Dolby NR on or off to match the

original tape.

This function allows you to make exact copies of both sides of

the original tape. The reverse side of both tapes will start

simultaneously as soon as the longer tape has been reversed.

m

● Dubbing does not start from a point halfway in the tape,

● The reverse mode is automatically set to =).

● The Dolby NR does not affect recording.

1

2

3

Press TAPE.

Insert the original tape into deck 1 and the tape

to be recorded on into deck 2.

Insert each tape with the side to be played back or recorded

on facing out from the unit.

Press SYNC DUB once or twice to start recording.

@lFor recording at normal speed, press it once to clispl;y

NORM-DUB.

@ For recording at high speed, press it twice to clisplay

HIGH-DUB.

@

The tapes are rewound to the beginning of the front sides,

and recording starts.

To stop dubbing

Press ■ ,

To set the Dolby NR when playing back the dubbed tape

Press DOLBY NR and turn Dolby NR on or off to match the

original tape.

m

Recording does not start, if the erasure prevention tab on either

side of the tape is broken off.

ENGLISH 18

6

Press

● REC/REC MUTE to start recording on

0-9,+10

The AI edit recording function enables CD recording without

worrying about tape length and track length. When a CD is

inserted, the unit automatically calculates the total track length.

If necessary, the order of tracks is rearranged so that no track is

cut short.

(Al: Artificial Intelligence)

m

Al edit recording will not start from a point halfway into the tape.

The tape must be recorded from the beginning of either side.

1

2

3

4

5

Insert the tape into deck 2, and press DOLBY NR

to turn Dolby NR on or off.

Insert the tape with the side to be recorded on first facing out

from the unit.

Press CD and load the disc(s).

Press CD EDIT/CHECK once.

“EDIT” is displayed.

EDIT

● When “PRGM” is displayed, press CD EDIT/CHECK again.

Press DISC DIRECT PLAY 1-3 to select a disc.

Press numbered buttons O-9 on the remote

control to designate the tape length.

10 to 99 minutes can be specified.

Example: When using a 60-minute tape, press 6 and O.

In a few seconds, the tracks to be recorded on each side of

the tape are determined.

● +, - or MULTI JOG are also available to designate

the tape length.

Remaining time Programmed

Tape length

of recording

tracks for side A

the first side.

The tape is rewound to the beginning of the front side, the

lead segment is played through for 10 seconds, and recording

starts. When recording on the front (side A) ends, recording

on the back (side B) starts.

To stop recording

Press ■ CLEAR. Recording and CD play stop simultaneously.

To clear the edit program

Press ■ CLEAR twice so that “EDIT” disappears on the display.

To check the order of the programmed track numbers

Before recording, press CD EDIT/CHECK to select side A or B,

and press + or - repeatedly.

Programmed

Traqk number

tra~k numbers

Program number

To add tracks from other discs to the edit program

If there is any time remaining on the tape after step 5, you can

add tracks from other discs in the CD compartment

1 Press CD EDIT/CHECK to select side A or B.

2 Press DISC DIRECT PLAY 1-3 to select a disc.

3 Press numbered buttons on the remote control to select tracks.

A track whose playing time is longer than the remaining time

cannot be programmed.

4 Repeat steps 2 and 3 to add more tracks.

Time on cassette tapes and editing time

The actual cassette recording time is usually a little longer than

the specified recording time printed on the label. This unit can

program tracks to use the extra time. When the total recording

time is a little longer than the tape’s specified recording time

after editing, the display shows the extra time (without a minus

mark), instead of the time remaining on the tape (with the minus

mark).

m

● Recording is inhibited if the erasure prevention tab on either

side of the tape is broken off.

● The Al edit recording function cannot be used with discs

containing 31 tracks or more.

Tape side

A: First recording side

B: Second recording side

i 9 ENGLISH

La page charge ...

Aiwa SX-R275 Operating Instructions Manual

Ce manuel convient également à

Aiwa SX-R275 Operating Instructions Manual

dans d''autres langues

Documents connexes

Autres documents