EGO Nexus PST3040 Manuel utilisateur

Taper
Manuel utilisateur

Ce manuel convient également à

WARNING: To reduce the risk of injury, the user must read and understand the
Operator’s Manual before using this product. Save these instructions for future reference.
NEXUS POWER STATION
OPERATOR’S MANUAL
56-VOLT
NEXUS POWER STATION
MODEL NUMBER PST3040/ PST3040-FC
PURE SINE WAVE
NEXUS POWER STATION
RESET
Español p. 67
Français p. 33
56-VOLT NEXUS POWER STATION - PST3040/ PST3040-FC2
TABLE OF CONTENTS
FCC Statement ...........................................4
Safety Symbols ..........................................5
Safety Instructions .....................................6-10
Introduction ............................................11
Specications ..........................................11
Packing List ............................................12
Description .........................................13-18
Operation ...........................................19-26
Maintenance ...........................................27
Troubleshooting ......................................28-29
Warranty ...........................................30-31
56-VOLT NEXUS POWER STATION - PST3040/ PST3040-FC 3
READ ALL INSTRUCTIONS!
READ & UNDERSTAND
OPERATOR’S MANUAL
WARNING: To reduce the risk of injury, re, or electric shock, the user must read
and understand the operator’s manual for their USB accessories and AC devices in
addition to this Operator’s Manual. Ensure compatibility before using this power station.
Do not use this product if a part is damaged or missing.
56-VOLT NEXUS POWER STATION - PST3040/ PST3040-FC4
FCC STATEMENT
1. This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
1) This device may not cause harmful interference.
2) This device must accept any interference received, including interference that
may cause undesired operation.
2. Changes or modications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
NOTICE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one
or more of the following measures: Reorient or relocate the receiving antenna. Increase
the separation between the equipment and receiver. Connect the equipment into an
outlet on a circuit different from that to which the receiver is connected. Consult the
dealer or an experienced radio/TV technician for help.
56-VOLT NEXUS POWER STATION - PST3040/ PST3040-FC 5
SAFETY SYMBOLS
The purpose of safety symbols is to attract your attention to possible dangers. The
safety symbols and the explanations with them deserve your careful attention and
understanding. The symbol warnings do not, by themselves, eliminate any danger. The
instructions and warnings they give are no substitutes for proper accident prevention
measures.
WARNING: Be sure to read and understand all safety instructions in this
Operator’s Manual, including all safety alert symbols such as DANGER,” “WARNING,”
and “CAUTION before using this tool. Failure to following all instructions listed below
may result in electric shock, re, and/or serious personal injury.
SYMBOL MEANING
SAFETY ALERT SYMBOL: Indicates DANGER, WARNING, OR CAUTION. May
be used in conjunction with other symbols or pictographs.
WARNING: The operation of any power tools can result in foreign objects being
thrown into your eyes, which can result in severe eye damage. Before beginning power
tool operation, always wear safety goggles or safety glasses with side shields and a
full face shield when needed. We recommend a Wide Vision Safety Mask for use over
eyeglasses or standard safety glasses with side shields. Always use eye protection
which is marked to comply with ANSI Z87.1.
56-VOLT NEXUS POWER STATION - PST3040/ PST3040-FC6
SAFETY INSTRUCTIONS
This page depicts and describes safety symbols that may appear on this product. Read,
understand, and follow all instructions on the machine before attempting to assemble
and operate it.
V Volt Voltage
A Amperes Current
Hz Hertz Frequency (cycles per second)
W Watt Power
/DC
Direct Current Type or a characteristic of current
/AC
Alternating
Current
Type or a characteristic of current
°F
Fahrenheit
Temperature
Temperature
°C
Celsius
Temperature
Temperature
lb Pound Weight
kg Kilogram Weight
Read &
Understand
Operator’s
Manual
To reduce the risk of injury, user must read
and understand operator’s manual before
using this product.
Safety Alert Indicates a potential personal injury hazard.
56-VOLT NEXUS POWER STATION - PST3040/ PST3040-FC 7
Eye Protection
Always wear safety goggles or safety glasses
with side shields and a full face shield when
operating this product.
WIFI Indicates WIFI connection.
Bluetooth Indicates Bluetooth connection.
WARNING: Read and understand all instructions. Failure to
follow all instructions listed below may result in electric shock, re
and/or serious personal injury.
WARNING: Do not allow any liquid to get inside the power station, or electric
shock may occur.
56-VOLT NEXUS POWER STATION - PST3040/ PST3040-FC8
IMPORTANT SAFETY INSTRUCTIONS
WARNING: When using this product, basic precautions should always be
followed, including the following:
 Read all the instructions before using the product.
 NEVER leave the power station on and unattended. Unattended operation of this
product could result in personal injury or property damage. Switch off the power
station when not in use.
 To reduce the risk of injury, close supervision is necessary when the product is
used near children.
 Do not put ngers or hands into the product.
 Use of an attachment not recommended or sold by power station manufacturer
may result in a risk of re, electric shock, or injury to persons.
 To reduce risk of damage to the electric plug and cord, pull the plug rather than
the cord when disconnecting the power station.
 ALWAYS ensure that the power station charger-in cord is easily accessible during
operation to allow for quick disconnection from the mains.
 Inspect extension cords before use and replace with new cord if required. Contact
with worn or damaged extension cords could result in electrocution.
 Do not operate the power pack with a damaged cord or plug, or a damaged output
cable.
 Do not use a power station or appliance that is damaged or modied. Damaged or
modied products may exhibit unpredictable behavior resulting in re, explosion
or risk of injury.
 When charging the battery, work in a well-ventilated area and do not restrict
ventilation in any way.
 ALWAYS operate the power station in a clean, dry, well ventilated area. Make
sure hands are dry before touching this product. Water can conduct electricity!
Water which comes in contact with electrically charged components can transmit
electricity resulting in electrical shock to anyone contacting them.
 Do not expose the power station to rain or wet conditions. Water entering the
power station will increase the risk of electric shock.
56-VOLT NEXUS POWER STATION - PST3040/ PST3040-FC 9
 Do not insert battery packs into charging ports, plug the power station in, or plug
any device into the power station’s power receptacle if moisture is detected on or
in the power station.
 Place the power station on a stable, at surface where it will not fall or tip over.
 Do not use the power station to power medical or other critical devices.
 Under abusive conditions, liquid may be ejected from the battery; avoid contact. If
contact accidentally occurs, ush with water. If liquid contacts eyes, additionally
seek medical help. Liquid ejected from the battery may cause irritation or burns.
 Do not expose the power station to re or excessive temperature. Exposure to re
or temperature above 212°F (100°C) may cause explosion.
 The power station is not intended for any use other than charging USB electronics
(up to 2.1 Amp for each USB port) or AC devices (up to continuous 2000W for 3 AC
ports combined). Any other use may result in system shut down or even damage.
 Use power station only with EGO 56V portable battery packs. Use of any other
battery packs may create a risk of injury and re.
 The power station is not intended for use in a commercial repair facility.
 For the power station charger, basic precautions should always be followed,
including the following:
1) SAVE THESE INSTRUCTIONS - This manual contains important safety and
operating instructions for battery charger Models CH1700/CH1700-FC.
2) Before using battery charger, read all instructions and cautionary markings on
battery charger, battery, and product using battery.
3)
CAUTION: To reduce risk of injury, charge only EGO 56V, maximum
10000 mAh Li-Ion portable type rechargeable batteies. Other types of
batteries may burst causing personal injury and damage.
4) Dry location use only.
5) Do not expose to rain.
 Do not disassemble the power station, take it to a qualied service person when
service or repair is required. Incorrect reassembly may result in a risk of re or
electric shock.
56-VOLT NEXUS POWER STATION - PST3040/ PST3040-FC10
 Have your power station or the charger serviced by a qualied repairperson using
only identical replacement parts. This will ensure that the safety of the power
station is maintained.
 To reduce the risk of electric shock, unplug the power station from the outlet
before attempting any instructed servicing.
 Save these instructions. Refer to them frequently and use them to instruct
others who may use this tool. If you lend someone this tool, lend them these
instructions also to prevent misuse of the product and possible injury.
SAVE THESE INTRUCTIONS!
56-VOLT NEXUS POWER STATION - PST3040/ PST3040-FC 11
INTRODUCTION
Congratulations on your selection of the EGO Nexus Power Station. It has been
designed, engineered and manufactured to give you the best possible dependability
and performance.
Should you experience any problem you cannot easily remedy, please contact the EGO
customer service center 1-855-EGO-5656.
This manual contains important information on to the safe assembly, operation and
maintainance of your product. Read it carefully before using the product. Keep this
manual handy so you can refer to it at any time.
SERIAL NUMBER _____________________ DATE OF PURCHASE _________________
YOU SHOULD RECORD BOTH SERIAL NUMBER AND DATE OF PURCHASE AND KEEP IN A SAFE
PLACE FOR FUTURE REFERENCE
SPECIFICATIONS
Discharging
Input Voltage
56V
USB Output
5V
Max.2.1A (each USB port)
AC Output
120V ~ 60Hz
2000W, 3000W Peak (3 AC
ports combined)
Charging
Input 120V ~, 60Hz 170W
Output
56V
Charging Temperature
Range
41°F-104°F (5°C-40°C)
Operation Temperature Range 5°F - 104°F (-15°C - 40°C)
Storage Temperature Range -4°F - 158°F (-20°C - 70°C)
Weight (Without battery pack) 30.2 lb (13.7 kg)
56-VOLT NEXUS POWER STATION - PST3040/ PST3040-FC12
PACKING LIST
PART NAME QUANTITY
Power Station 1
Charger 1
Power Cord 2
Front Waterproof Cover 1
Back Waterproof Cover 1
Screws 7
Operator’s Manual 1
56-VOLT NEXUS POWER STATION - PST3040/ PST3040-FC 13
DESCRIPTION
KNOW YOUR POWER STATION (Fig.1a & 1b & 1c)
The safe use of this product requires an understanding of the information on the tool
and in this operator’s manual, as well as knowledge of the project you are attempting.
Before the use of this product, familiarize yourself with all its operating features and
safety rules.
PURE SINE WAVE
NEXUS POWER STATION
1a
Back Waterproof Cover
Front Waterproof Cover
Cover Release Button
Waterproof Cover for USB Ports
Waterproof Cover for AC Ports
Battery-mounting Slots
Latch
Electric Contacts
Handle
Screw
Screw
Cover
Charger
Power Cords
Velcro Straps
LCD Screen
56-VOLT NEXUS POWER STATION - PST3040/ PST3040-FC14
1b
Charger Socket
Fuse (80A)
Fuse Compartment Cover
Air Outles
RESET
NEXUS POWER STATION
RESET
NEXUS POWER STATION
1c
USB Ports
AC Ports
Power Button
Reset Button
USB Button
Air Inlets
AC Button
WIFI/Bluetooth
Setting Button
56-VOLT NEXUS POWER STATION - PST3040/ PST3040-FC 15
Charger
The power station can charge up to four EGO portable batteries through the supplied
charger and the power cords.
Handle
To help lift the power station.
Cover
To support the charger, as well as a cover for power-cord storage.
Velcro Straps
To secure the charger to the cover for compact convenience.
Power Cords
There are two power cords. One is for connecting the charger with the power station;
the other is for connecting the charger with the power supply. The power station can
charge EGO portable battery(s) once the connections are completed.
LCD Screen
To display the working status of the power station.
Front/Back Waterproof Cover
The front and back waterproof covers are not assembled when shipping. They are
separately stored in the package. The users can mount them with the screws provided,
as needed.
Latch
To help securely lock the battery when installing the battery on the power station.
Charger Socket
To connect the power station to the charger with the provided power cord.
56-VOLT NEXUS POWER STATION - PST3040/ PST3040-FC16
Power Button
To turn on/off the power station.
Reset Button
To recover the power station when it is overloaded.
AC and USB Ports
To connect with AC and USB devices. There are 3 AC ports and 4 USB ports.
AC and USB Button
To switch on/off the AC and USB port output.
WIFI/Bluetooth Setting Button
To congure WIFI/Bluetooth connection and indicate conguration status.
KNOW THE ICONS AND INDICATORS ON THE LCD SCREEN (Fig. 2)
2
Over-heat Icon WIFI Icon Bluetooth Icon USB Icon AC Icon Peak-power Indicator Overload Reminder
Actual Output
Power Indicator
Overload Indicator
Countdown Timer
Rated Power IndicatorLow-power Indicator
Battery
Indicator
Area
Warning Indicator
Output
Indicator
Charging
Indicator
Charge-
complete
Indicator
56-VOLT NEXUS POWER STATION - PST3040/ PST3040-FC 17
Output Indicator
Illuminates to show that the power station is in the discharging process when the AC/
USB button is switched on.
Charging Indicator
Illuminates to show the power station is in the charging process.
Charge-complete Indicator
The charge-complete indicator, together with the charging indicator will illuminate to
indicate that the charging is completed.
Actual Output Power Indicator
Illuminates different numbers of the segments to indicate the actual output power
when a device is connected to the output port.
Rated Power Indicator (600W, 1200W, 2000W)
The rated maximum continuous output power depends on the attached battery(s) on
the Nexus power station.
Peak-power Indicator (3000W)
When the actual output power is over 2000W, but less than 3000W, for LESS THAN
3 seconds, this indicator will illuminate, as well all the segments of the actual output
power.
Overload Indicator
This indicator is separated into 3 segments. When the actual output power is over the
rated power, the corresponding segment will illuminate in red. The overload reminder
“PRESS AND HOLD RESET BUTTON” and the warning indicator ” will illuminate in
red at the same time. Remove the device and then press and hold the reset button to
reactivate the power station.
56-VOLT NEXUS POWER STATION - PST3040/ PST3040-FC18
Low-power Indicator
Illuminates when the available battery charge is 10% or less of the rated total battery
charge during discharging. No available time will be displayed on the LCD screen and
the power station will stop discharging when all batteries are fully discharged.
Warning Indicator
Illuminates when a problem occurs and the power station cannot work properly.
Battery Indicator Area
Each indicator includes three aspects:
 The upper and lower polygonal areas indicate the status of the associated battery;
 The circled power indicator in segments indicates the remaining battery charge;
 The battery number indicates the battery position.
Over-heat Icon
Illuminates when the Nexus is overheated. The system will shut down.
WIFI Icon
Illuminates when the Nexus is connected to a WIFI Network.
Bluetooth Icon
Illuminates when the Nexus is connected to cell phone via Bluetooth.
USB/AC Icon
Illuminates to indicate that the USB/AC port has been turned on.
Countdown Timer
This timer indicates the remaining time of charging or discharging process. When the
Nexus stops working or is in low power condition, no timer will be displayed.
56-VOLT NEXUS POWER STATION - PST3040/ PST3040-FC 19
OPERATION
WARNING: Do not allow familiarity with this product to make you careless.
Remember that a careless fraction of a second is sufcient to inict serious injury.
WARNING: Do not use any attachments or accessories not recommended by the
manufacturer of this product. The use of attachments or accessories not recommended
can result in serious personal injury.
WARNING: Do not modify or attempt to repair the Nexus power station except
indicated in the instructions for use and care.
CAUTION: This device is not intended for use in a commercial repair facility.
CAUTION: The device shall be stored indoors and protected from the elements.
The unit shall not be charged outdoors. When in use, steps should be taken to reduce
the exposure to rain, sleet, snow, and the like.
APPLICATION
You may use this product for power emergencies, camping, and any time you need
power for long periods of time.
The Nexus power station provides 4 USB ports and 3 AC ports. Each USB port can
supply a 5V DC, up to 2.1Amp output to power the USB devices like your cell phone,
tablets, etc. The 3 AC ports combined can supply a 120V AC, continuous 2000W (Peak
3000W for less than 3s) output to power AC devices, such as full-size refrigerator, TV,
laptop, etc.
The Nexus power station is equipped with a charger to charge up to four EGO portable
batteries.
56-VOLT NEXUS POWER STATION - PST3040/ PST3040-FC20
CHARGING EGO PORTABLE BATTERIES (Fig. 3)
3
Power Supply
Supplied Charger
Supplied Power Cords
Battery
1. Connect the supplied charger between the power supply (120V~, 60Hz) and
the Nexus power station with the two supplied power cords. Make sure that the
connections are secure and reliable.
2. Align the raised ribs of the battery pack with the mounting slot in the Nexus
power station; slide the battery pack down onto the Nexus. Make sure that the
battery is securely attached to the Nexus.
3. The Nexus power station will communicate with the battery pack and begin
charging the battery.
4. The charging indicators on the LCD screen will illuminate and the power button
will slowly blink green. The screen displays the remaining charge time in
hours and minutes until the battery will be fully charged. When the charging is
completed, the charge-complete indicator will also illuminate and the power
button will shine solid green.
NOTE: During the charging process, the LCD screen may turn black no display. You
can press any of the Power/USB/AC/Reset buttons or reattach the battery to reactivate
the display.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100

EGO Nexus PST3040 Manuel utilisateur

Taper
Manuel utilisateur
Ce manuel convient également à

dans d''autres langues