Bercomac 700382 700384 Manuel utilisateur
- Catégorie
- Tondeuses à gazon
- Taper
- Manuel utilisateur
Ce manuel convient également à
1
OWNER’S MANUAL
Model Number
700382 Subframe
700383 Compact Drive Mechanism
700384 Northeast Drive Mechanism
Berco
Subframe & Drive Mechanism
for
HUSQVARNA, JONSERED, POULAN, RALLYE, WEEDEATER & YARD PRO
tractors
CAUTION:
READ & FOLLOW ALL SAFETY RULES & INSTRUCTIONS BEFORE
OPERATING YOUR EQUIPMENT
104090 F-07
* ASSEMBLY * REPAIR PARTS
* OPERATION * MAINTENANCE
2
WARRANTY
LIMITED ONE YEAR WARRANTY ON BERCO TRACTOR ATTACHMENTS
For one year from date of purchase, Bercomac Limitée will repair or replace free of charge at Bercomac's option, any
parts which are defective as a result of defective materials or faulty workmanship.
COMMERCIAL OR RENTAL USE:
Warranty on Berco attachments used for commercial or rental purposes is limited to 90 days.
This warranty does NOT cover:
* Wear items, such as shear pins and belts.
* Repairs due to customer abuse or neglect.
* Pre-delivery set-up.
* In home service.
Warranty service is available by returning the "Berco" attachment to the authorized dealers.
BERCOMAC Limitée
92 Fortin N, Adstock, Québec, Canada, G0N 1S0
1
TABLE OF CONTENTS
INTRODUCTION ................................................................................................................................................... 2
SAFETY PRECAUTIONS ..................................................................................................................................... 3
ASSEMBLY
Step 1: Tractor Preparation ................................................................................................................... 5
Step 2: Subframe Installation ................................................................................................................. 6
Step 3: Drive Mechanism Preparation ................................................................................................... 10
Step 4: Drive Mechanism Installation ..................................................................................................... 12
Step 5: Snowblower Installation ............................................................................................................. 13
Rotary Broom Installation .......................................................................................................... 15
Blade Installation ........................................................................................................................ 17
MAINTENANCE & DISMOUNTING
Maintenance ............................................................................................................................................. 18
Drive Mechanism Dismounting ............................................................................................................... 18
Belt Replacement ..................................................................................................................................... 18
End of Season Storage ........................................................................................................................... 18
TORQUE SPECIFICATION TABLE ..................................................................................................................... 19
PARTS BREAKDOWN AND LISTS
Compact Drive Mechanism ..................................................................................................................... 20
Northeast Drive Mechanism .................................................................................................................... 22
Subframe .................................................................................................................................................. 24
ATTACHMENTS .................................................................................................................................................... 27
TROUBLESHOOTING
See attachment owner’s manual for this section. (Snowblower, Blade, Rotary Broom)
PAGE
2
INTRODUCTION
INTRODUCTION
TO THE PURCHASER
This new attachment was carefully designed to give years of dependable service. This manual has been provided to
assist in the safe operation and servicing of your attachment.
NOTE: All photographs and illustrations in the manual may not necessarily depict the actual models or attachment, but
are intended for reference only and are based on the latest product information available at the time of publication.
Familiarize yourself fully with the safety recommendations and operating procedures before putting the machine to use.
Carefully read, understand and follow these recommendations and insist that they be followed by those who will use
this attachment.
THIS SAFETY ALERT SYMBOL IDENTIFIES AN IMPORTANT SAFETY MESSAGE IN THIS MANUAL
THAT HELPS YOU AND OTHERS AVOID PERSONAL INJURY OR EVEN DEATH. DANGER,
WARNING, AND CAUTION ARE SIGNAL WORDS USED TO IDENTIFY THE LEVEL OF HAZARD.
HOWEVER, REGARDLESS OF THE HAZARD, BE EXTREMELY CAREFUL.
DANGER: Signals an extreme hazard that will cause serious injury or death if recommended precautions are
not followed.
WARNING: Signals a hazard that may cause serious injury or death if the recommended precautions are not
followed.
CAUTION: Signals a hazard that may cause minor or moderate injury if the recommended precautions are not
followed.
Record your attachment serial number and purchase date in the section reserved below (there is no serial number on
the subframe). Your dealer requires this information to give you prompt, efficient service when ordering replacement
parts. Use only genuine parts when replacements are required.
If warranty repairs are required please present this registration booklet and original sales invoice to your selling dealer
for warranty service.
This manual should be kept for future reference.
Please check if you have received all the parts for your kit with the list of the
bag and the list of the box.
7
SERIAL NUMBER : ___________________________
PURCHASE DATE : ___________________________
In this manual, right and left sides are determined by sitting on the tractor seat facing forward.
In this manual, "attachment" means accessories that you install on the tractor, such as, snowblower, rotary
broom, blade, rotary tiller, cab, subframe, etc...
3
SAFETY PRECAUTIONS
TRAINING
This symbol, "Safety Alert Symbol", is used
throughout this manual and on the attachments
safety labels to warn of the possibility of serious
injuries. Please take special care in reading and
understanding the safety precautions before
operating the attachment or the tractor.
1. Read this owner's manual carefully. Be thoroughly
familiar with the controls and proper use of the
tractor and attachment. Know how to stop the unit
and disengage the controls quickly.
2. Never allow children to operate attachment nor the
tractor. Never allow adults to operate attachment
nor the tractor without proper instructions.
3. No one should operate the tractor nor the
attachment while intoxicated or while taking
medication that impairs the senses or reactions.
4. Keep the area of operation clear of all persons,
particularly small children and pets.
PREPARATION
1. Thoroughly inspect the area where the attachment
is to be used and remove door mats, all foreign
objects and the like.
2. Disengage all clutches and shift into neutral before
starting engine
3. Do not operate the attachment without wearing
adequate garments. Avoid loose fitting clothing that
can get caught in moving parts. Wear footwear that
will improve footing on slippery surfaces.
4. Handle fuel with care, it is highly flammable.
a) Use approved fuel container.
b) Never add fuel to a running engine or hot
engine.
c) Fill fuel tank outdoors with extreme care. Never
fill fuel tank indoors.
d) Never fill containers inside a vehicle, or on a
truck or a trailer bed with a plastic liner. Always
place containers on the ground, away from your
vehicle, before filling.
Careful operation is your best insurance against an accident. Read this section carefully before operating the tractor
and attachment. Failure to observe the following safety instructions could result in serious injury. All operators, no
matter how experienced they may be, should read this and other manuals related to the tractor and attachments before
operating. It is the owner's legal obligation to instruct all operators in safe operation.
7
e) When practical, remove gas-powered equipment
from the truck or trailer and refuel it on the
ground. If this is not possible, then refuel such
equipment on a trailer with a portable container,
rather than from a gasoline dispenser nozzle.
f) Keep the nozzle in contact with the rim of the
fuel tank or container opening at all times, until
refuelling is complete. Do not use a nozzle lock-
open device.
g) Replace fuel cap securely and wipe up spilled
fuel.
h) If fuel is spilled on clothing, change clothing
immediately.
5. Never attempt to make any adjustments while
engine is running (except where specifically
recommended by manufacturer).
6. Always wear safety glasses or eye shields during
operation or while performing an adjustment or
repairs to protect eyes from foreign objects that may
be thrown from the machine.
7. Never modify the attachment or any part without
the written consent from the manufacturer.
OPERATION
1. Do not run engine indoors except when starting
engine and transporting attachment, in or out of
building. Do not operate or let motor run in a
storage area without ventilation because gas
contains carbon monoxide which is odourless,
colourless and can cause death.
2. Do not carry passengers on attachment or tractor.
3. Take all possible precautions when leaving the
machine unattended. Lower the attachment, shift
into neutral, set the parking brake, stop the engine
and remove the key. Wait for all moving parts to
stop.
4
SAFETY PRECAUTIONS
WHENEVER YOU SEE THIS SYMBOL
7
IT MEANS:
WARNING!
BECOME ALERT !
YOUR SAFETY IS INVOLVED!
7 WARNING 7
FOR YOUR SECURITY:
Read the attachment owner's manual for safety
precautions and rules.
Follow the assembly and operation instructions.
7 WARNING 7
TO PREVENT INJURIES AND FOR MORE
TRACTION WHEN USING AN ATTACHMENT:
-Rear counterweight of 100 lbs. minimum is
required to counterbalance the attachment’s
weight.
-Tractor manufacturer approved tire chains are
required.
-Do not operate on a slope greater than 10°.
-When dismounting an attachment remove rear
counterweights.
4. Use only attachments approved by the
manufacturer (such as wheel chains,
counterweights, cabs). You must use 100 lbs. of
rear counterweight for better traction and a greater
stability at all times when using an attachment that
is installed on the front of a tractor.
5. Never operate an attachment without good visibility
or light.
MAINTENANCE AND STORAGE
1. Check shear bolts, mounting bolts, etc..., at frequent
intervals for proper tightness to be sure attachment is
in safe working condition.
2. Never store the machine with fuel in the tank inside a
building where ignition sources are present, such as
hot water tanks, space heaters, clothes dryers and
the like. Allow engine to cool before storing in any
enclosure.
3. Always refer to the owner’s manual when you store
than attachment for an extended period.
4. Maintain or replace safety and instructions labels, as
necessary.
5
ASSEMBLY
IMPORTANT: TORQUE ALL BOLTS ACCORDING
TO TORQUE SPECIFICATION TABLE (SEE TABLE
OF CONTENTS) WHEN STATED: TIGHTEN
FIRMLY. REFER TO PARTS BREAKDOWN
SECTION FOR PARTS IDENTIFICATION.
NOTE: This subframe was designed to fit various
models of Lawn, Yard or Garden tractors. (See
illustrations to identify your tractor).
This subframe may be used to install different
attachments (see attachments page). Once installed,
it may remain permanently on the tractor. Before
doing any modifications or installations on the tractor,
open the tractor hood, disconnect the headlights and
remove the hood. Disconnect the wire from the spark
plug(s) and keep away from spark plug(s) to prevent
accidental starting.
STEP 1
TRACTOR PREPARATION:
IT IS NOT NECESSARY TO REMOVE THE MOWER
DECK AT THIS STEP.
According to the model of the tractor, remove the front
attaching supports if they are bolted to the outside of the
tractor’s frame (one on each side) and the heat shield
(save the bolts to install the new heat shield).
In order to install the subframe’s supports, it may be
necessary to remove certain bolts or certain parts.
NOTE: Take note of the place and how the bolts and
parts were installed in order to reinstall them in the same
manner as before.
If applicable, make sure that the belt guide does not
touch any part when reinstalled.
How to:
Take the right support (item 1) and place it on the right
side of the tractor’s frame.
Align the hole (item 2) on the right support with the hole
(item 3) which is about 2” (according to the model of the
tractor) from the edge of the tractor’s front frame.
Remove all the bolts and parts from the tractor’s frame
that will interfere with the installation of the support.
Do the same operation on the left side.
Align the holes in order to identify and remove the
bolts and/or parts that come into interference
Back end of Garden Tractor
Back end of Lawn & Yard Tractors
6
ASSEMBLY
FOR LAWN & YARD TRACTORS:
On the right side install the right support (item 2) and
hold in place with three thread cutting screw 3/8 x 1"
(item 3), one carriage bolt 5/16 x 1 (item 6) the head
inside, one flange nut on the outside, one carriage
bolt 3/8 x 1" (item 4) the head inside, one flange nut
on the outside.
Slightly tighten the screws and bolts.
Slide the shim (item 1) between the tractor frame and
the right support. Secure in place with a 3/8 x 1"
carriage bolt the head inside (item 5) and with a
flange nut.
(Make sure that the shim stays perpendicular with the
top of the support).
Install the square head set screw 5/16 x 1/2" (item 7).
Do not tighten the bolts nor nuts.
FOR GARDEN TRACTORS:
On the right side, install the shim (item 1) between the
tractor frame and the right support (item 2) (make
sure that the shim stays perpendicular with the top of
the support) with four thread cutting screws 3/8 x
1" (item 3).
Install the square head set screw 5/16 x 1/2" (item 4).
Do not tighten the screws.
Install right support on the Lawn & Yard tractors
Install the right support on Garden tractor
Install brace pin
FOR LAWN & YARD TRACTORS:
Install a hex. nut 1/2" (item 1) on each end of the
brace pin (item 2) (halfway down the threads).
Install the longest end (item 2) of the brace pin in the
top nut (item 4) welded on the right support.
FOR GARDEN TRACTORS:
Install a hex. nut 1/2" (item 1) on each end of the
brace pin (item 2) (halfway down the threads).
Install the longest end (item 2) of the brace pin in the
bottom nut (item 3) welded on the right support.
STEP 2
SUBFRAME INSTALLATION:
7
FOR LAWN & YARD TRACTORS:
Install the left support (item 1) by inserting the top
hole (item 3) on the brace pin (item 2) as shown in
figure A.
Hold in place with three thread cutting screws 3/8 x
1" (item 4), a carriage bolt 5/16 x 1" (item 5) (the head
inside) and a flange nut.
Install the handle support (item 7) and secure in place
with a hex bolt 3/8 x 1" (the head inside) (item 8) in
the bottom hole. Secure with a flange nut.
Slide the shim (item 6) between the tractor frame and
the support. (Make sure that the shim stays
perpendicular with the top of the support).
Secure with the last hex bolt 3/8 x 1" (the head inside)
(item 8) in the top hole of the handle support and
secure with a flange nut.
Slightly tighten the screws and bolts.
Make sure that the brace pin (figure A, item 2) stays
straight and does not come into contact with any part
of the tractor (ex: the engine belt when mower deck is
in raised position).
If you have removed the original supports from the
tractor, in order to install the mower brackets (item
12) (included in this kit) inside the support, insert two
hex. bolts 3/8 x 1 1/4" (item 10) (the heads on the
outside) in the top holes of the right support .
To the inside of the support, insert the shim (item 11)
and the mower bracket (item 12) on the bolts. Secure
with two flange nuts.
Do the same operation on the left side.
Tighten firmly.
Install the new heat shield (item 13) with the bolts
previously removed.
Install the plastic grommet (item 14) as shown.
Install the square head set screw 5/16 x 1/2" (item 15)
in the cab support.
Reinstall the parts:
Reinstall the parts previously removed in their original
position. If applicable, in order to facilitate reinstallation
of the parts, you may remove the lever (item 9) and
reinstall it afterwards.
(If necessary, use the bolts supplied for this purpose).
Make sure the belt guide is functional and adjust in
order to compensate for the thickness of the right
support. Install the mower brackets inside the support and
other parts if applicable.
Figure A
ASSEMBLY
Install the left support and
the handle support on Lawn & Yard tractors
8
ASSEMBLY
FOR GARDEN TRACTORS:
Install the left support (item 1) by inserting it on the
brace pin (item 2) as shown in figure A.
Hold in place with two thread cutting screws 3/8 x
1" (item 4). Install and the handle support (item 5)
with a hex bolt 3/8 x 1" (item 6) (the head inside) in
the bottom hole and a flange nut.
Slide the shim (item 3) between the tractor frame and
the left support (item 1) (make sure that the shim
stays perpendicular with the top of the support) with
the last hex bolt 3/8 x 1" (item 6) (the head inside)
and a flange nut.
Make sure that the brace pin (figure A, item 2) stays
straight and does not come into contact with any part
of the tractor (ex: the engine belt when mower deck is
in raised position). If it does, turn the brace pin to use
another hole created for this purpose.
If you have removed the original supports from the
tractor, in order to install the mower brackets (item 9),
(included in this kit) inside the support insert two hex.
bolts 3/8 x 1 1/4" (item 7) (the heads on the outside)
in the bottom holes of the right support.
To the inside of the support, attach the shim (item 8)
and the mower bracket (item 9) on the bolts. Secure
with two flange nuts.
Do the same operation on the left side.
Tighten firmly.
Secure the heat shield with a thread cutting screw 3/8
x 1" (item 10) and a spacer (item 11) on each side as
shown.
Install the plastic grommet (item 12) as shown.
Install the square head set screw 5/16 x 1/2" (item 13)
in the cab support.
Reinstall the parts:
Reinstall the parts previously removed in their original
position. If applicable, in order to facilitate reinstallation
of the parts, you may remove the lever (item 14) and
reinstall it afterwards.
(If necessary, use the bolts supplied for this purpose).
Make sure the belt guide is functional and adjust in
order to compensate for the thickness of the right
support.
Install the left support and the handle support
Figure A
3 possible positions for
the brace pin
Install the mower brackets inside the support
9
FOR LAWN, YARD AND GARDEN TRACTORS:
Turn the front wheels towards the left.
Install the pivot support (item 1) between the two
supports and slide in place the pin (item 2) in the top
hole for Lawn & Yard tractors or the bottom hole for
Garden tractors.
Secure with the hair pin (item 3).
Tighten all the bolts.
Adjust the inside left hand side nut and right hand
side nut of the brace pin (item 4) until they come into
contact with the supports. Secure the brace pin with a
hex nut 1/2" (item 5) on the left hand side.
Tighten the three nuts.
Insert the nylon bushing (item 6) in the lift arm (item
7). Insert the lift arm on the tube (item 8) of the right
support. Install the link (item 9), one end on the lift
arm pin and the other end on the lever pin.
Secure with two washers (item 10) and two hair pins
2.5mm (item 11).
Install the bended part of the link (item 12) (angle
towards the inside) on the pivot support pin (item 13)
and insert the other end of link on the lever pin (item
14).
Secure each end with a washer (item 15) and a hair
pin 3mm (item 16).
Install the handgrip (item 17) on the lift arm as shown.
ASSEMBLY
Install the lift arm
Install the pivot support and adjust the
nuts on the brace pin.
ASSEMBLY
10
VERY IMPORTANT
ADJUST THE LIFT HEIGHT OF THE
ACCESSORIES ON LAWN, YARD AND GARDEN
TRACTORS.
This adjustment is necessary in order to allow the
accessories to follow the contours of the ground
and to avoid damage to the accessories.
The link (item 1) has an adjustment bolt (item 2) to
adjust the height of the accessories:
Compact Snowblower: max. 4" from the ground.
Northeast Snowblower: max. 4" from the ground.
Rotary Broom: 1 1/2" over the swivel wheels.
Utility Blade: no restrictions.
When the adjustment is done tighten the lock nut.
ALSO SEE ACCESSORY INSTALLATION SECTION FOR TIRE
PRESSURE.
NON COMPLIANCE WITH THESE INSTRUCTIONS
MAY DAMAGE THE BELTS AND THE DRIVE
MECHANISM.
STEP 3
DRIVE MECHANISM PREPARATION:
NOTE: You must remove the mower deck to install
and use the drive mechanism.
Remove the left mower bracket.
Keep these parts for reinstallation of the mower deck.
FOR LAWN & YARD TRACTORS:
Secure the square supports as shown with two
carriage bolts 3/8 x 3/4" (item 1) the heads inside.
Secure with two flange nuts.
Do the same operation on other side.
Note: Due to the wide variety of tractor models on
the market, these supports can be installed in
different ways. See illustration A or B.
FOR GARDEN TRACTORS:
To install the drive mechanism, you must remove the
two bolts from the footrests (from each side).
Secure the left support (longest support with point
towards the front) and the right support (shortest
support with point towards the front) with the bolts
removed from the footrests. See figure A.
Adjust the lift height of the accessories
ASSEMBLY
Figure A,
Install supports on
Garden tractor
Install supports on
Lawn & Yard tractors
11
ASSEMBLY
NOTE: This drive mechanism may be mounted on
tractors with two types of clutch mechanisms. See the
following instructions for those that are appropriate for
your tractor.
GARDEN TRACTORS WITH AN ELECTRIC
CLUTCH.
No modifications are needed.
LAWN & YARD TRACTORS WITH AN ELECTRIC
CLUTCH
Remove the spring already installed on the idler arm
(item 1).
Remove the support (item 2) and the shim (item 3) by
removing the two bolts (item 4). Reinstall the support
(item 2) and the shim (item 3) as shown in figure A.
Secure with the bolts (item 4) and tighten firmly.
Reinstall the spring on idler arm (item 1).
LAWN & YARD TRACTORS WITH A MANUAL
CLUTCH ACTIVATED BY A CABLE.
Remove the spring that is hooked to the idler arm
(item 1)
Remove the support (item 2) and the shim (item 3) by
removing the two bolts (item 4). Reinstall the support
(item 2) without the shim as shown in figure B.
Secure with the bolts (item 4) and tighten firmly.
Reinstall the spring on idler arm (item 1).
Cut the tie wrap that holds the cable to the frame.
NOTE: Depending on the mower deck model, there
are two different cable lengths. To determine where to
place the cable holder, hook the end of the cable
spring (item 5) on the idler arm (item 1). Slide the
cable shield (item 6) temporarily into the slot on the
cable holder (item 7). To identify into which holes the
cable holder will be bolted in, you must apply a slight
tension on the cable. This adjustment must be done
with the clutch arm in the off position.
Remove the cable shield and secure the cable holder
(item 7) on the frame using two 1/4 x 3/4" hex bolts
(item 8) and flange nuts.
Reinstall the cable shield into the cable holder and
secure with the hair pin previously removed.
Install cable holder
Figure B
Install the support without shim for manual clutch as
shown.
Figure A
Install the support with shim for electric clutch as
shown
NOTE: The drive mechanism must be straight, to
make sure the belt works well.
12
ASSEMBLY
STEP 4
DRIVE MECHANISM INSTALLATION:
Install the drive mechanism according to the
appropriate figure for you tractor.
Install the drive mechanism (item 1) by hooking the
front part of the drive frame (item 2) on the brace pin
(item 3).
Lift and attach the rear portion of the drive frame
between the supports (items 4 & 5) by inserting a pin
(item 7) on each side. Secure with two 2.5 mm hair
pins (item 6).
Install the primary belt on the engine pulley and route
inside the belt guide.
ON LAWN & YARD TRACTORS:
Make sure the drive mechanism pulley is aligned with
the engine pulley. If not, you may change the position
of the square supports (item 5) as needed.
NOTE: After installation, attach the cable to the frame
with the new tie wrap supplied with this kit.
Install drive mechanism on Lawn & Yard tractors
with manual clutch.
NOTE:Electric Clutch :
If your tractor is equipped with an electric clutch,
make sure the spring is well inserted in its place and
the belt does not touch the belt guides at any point.
NOTE: Manual Clutch:
If your tractor is equipped with a manual clutch, make
sure the belt guide does not touch the belt at any
point while the drive mechanism is engaged or
disengaged.
7 WARNING 7
TO PREVENT INJURIES DO THIS VERIFICATION
WHEN THE ENGINE IS STOPPED.
Install drive mechanism on Lawn & Yard tractors
with electric clutch.
Install drive mechanism on Garden tractor with
electric clutch.
13
ASSEMBLY
Attach the snowblower to the subframe as shown.
Make sure the snowblower is pushed in until locked
into place by the springs (item 4).
Lift the snowblower by pulling the lift arm. Turn the
tension arm (item 1) towards the back. Hook the
chain (item 2) (of the helper spring) on the tip (item 3)
of the left support intended for this purpose. Turn the
tension arm towards the front to apply tension on the
spring.
Lower the snowblower.
STEP 5
SNOWBLOWER INSTALLATION:
Refer to snowblower owner’s manual, parts breakdown
section for parts identification.
Install snowblower and lift assist spring
7 WARNING 7
FOR YOUR SECURITY:
Read the snowblower’s owner's manual for safety
precautions and rules.
Follow the assembly and operation instructions.
7 WARNING 7
TO PREVENT INJURIES:
Stop the motor.
Apply parking brake.
Remove the ignition key.
Disconnect the wire from the spark plug(s) and
keep away from spark plug(s) to prevent accidental
starting.
7 CAUTION 7
Never use the snowblower without the belt guard.
7 CAUTION 7
The belt tension arm and lift assist spring are
spring loaded & needs to be held firmly while
displacing to prevent injury.
BELT INSTALLATION:
Remove the belt guard.
Install the belt around the pulleys as shown.
Install the belt on the drive mechanism pulley (item 5)
under the tractor.
Apply tension on the belt by pulling up the belt
tension arm.
Reinstall the belt guard.
NOTE: See belt replacement instructions in the
maintenance section of the snowblower owner’s
manual.
Item 1: Snowblower pulley
Item 2: Tractor engine pulley
Item 3: Flat pulley L.H.
Item 4: Flat pulley R.H.
Item 5: Drive mechanism pulley
Item 6: Drive mechanism belt
Item 7: Snowblower belt Install-belt and belt guard
14
ASSEMBLY
Insert the handgrip (item 1) on the handle (item 2).
Insert the handle (item 2) through the support (item 3)
as shown.
Insert the handle (item 2) in the rotation worm (item 5)
and secure with a 2.5 mm. hair pin (item 4).
VERIFY SKID SHOE ADJUSTMENT:
LEVEL PAVED SURFACE: Adjust skid shoes to allow
3/16" to 1/4" clearance (A) between cutting edge and
surface.
UNEVEN OR GRAVEL SURFACE: Adjust skid shoes
to allow 1/2" to 5/8" clearance (A) between cutting
edge and surface.
VERIFY TIRE PRESSURE:
Check and adjust tractor tire pressure as follows:
Front tires: 14-15 psi
Back tires: 7-8 psi
Tire pressure must be even on both sides of tractor.
Install handle
Adjust skid shoe
VERIFY BELT ROUTING:
-Lower the snowblower to the ground and let it run for
a few seconds under supervision.
-Disengage the snowblower and stop the engine.
-Remove the belt guard.
-Check the belts to make sure they are well inserted
on the pulleys and have not flipped on their sides in
the pulleys and that they do not touch the belt
guides.
-Reinstall the belt guard.
7 WARNING 7
TO PREVENT INJURIES:
It is the person who installs the drive mechanism
responsibility to make sure that when the clutch
is disengaged that all moving parts stop.
For more information, do not hesitate to contact
the technical support.
15
ASSEMBLY
Attach the rotary broom to the subframe as shown.
Make sure the rotary broom is pushed in until locked
into place by the springs (item 1).
Install belt
ROTARY BROOM INSTALLATION:
Refer to rotary broom owner’s manual, parts
breakdown section for parts identification.
BELT INSTALLATION
NOTE: See belt replacement instructions in the
maintenance section of the owner’s manual for the
broom.
Remove the belt guard.
Install the belt on the drive mechanism pulley (item 1)
as shown.
Reinstall the belt guard.
TIP: Because of strong tension on the spring and to
facilitate installation of the belt, the broom must be on
the ground and remove the belt from the engine
pulley.
VERIFY BELT ROUTING:
-Lower the rotary broom to the ground and let it run
for a few seconds under supervision.
-Disengage the rotary broom and stop the engine.
-Check the belts to make sure they are well inserted
on the pulleys and have not flipped on their sides in
the pulleys and that they do not touch the belt
guides.
Install rotary broom
Item 1: Drive mechanism pulley
Item 2: Rotary broom pulley
7 WARNING 7
FOR YOUR SECURITY:
Read the Rotary Broom owner's manual for
safety precautions and rules.
Follow the assembly and operation instructions.
7 WARNING 7
TO PREVENT INJURIES:
Stop the motor.
Apply parking brake.
Remove the ignition key.
Disconnect the wire from the spark plug(s) and
keep away from spark plug(s) to prevent accidental
starting.
7 CAUTION 7
Never use the Rotary Broom without the belt
guard.
7 WARNING 7
TO PREVENT INJURIES:
It is the person who installs the drive mechanism
responsibility to make sure that when the clutch is
disengaged that all moving parts stop.
For more information, do not hesitate to contact
the technical support.
16
ASSEMBLY
Insert handgrip on the handle.
Insert the handle (item 1) through the support (item 2)
as shown.
Install the handle on the control rod (item 3) as shown
and secure with a 2.5 mm. hair pin (item 4).
VERIFY TIRE PRESSURE:
Check and adjust tractor tire pressure as follows:
Front tires: 14-15 psi
Back tires: 7-8 psi
Tire pressure must be even on both sides of the
tractor.
Install handle
17
ASSEMBLY
Attach the blade to the subframe as shown.
Make sure the blade is pushed in until locked into
place by the springs (item 1).
Insert the handgrip on the handle.
Insert the handle (item 1) through the handle support
(item 2) as shown.
Install the handle on the control rod (item 3) as shown
and secure with a 2.5 mm hair pin (item 4).
VERIFY TIRE PRESSURE:
Check and adjust tractor tire pressure as follows:
Front tires: 14-15 psi
Back tires: 7-8 psi
Tire pressure must be even on both sides of the
tractor.
Install the blade
BLADE INSTALLATION:
Refer to blade owner’s manual, parts breakdown
section for parts identification.
Install handle
7 WARNING 7
FOR YOUR SECURITY:
Read the Blade owner's manual for safety
precautions and rules.
Follow the assembly and operation instructions.
18
MAINTENANCE & DISMOUNTING
MAINTENANCE
a) Check mounting bolts at frequent intervals for
proper tightness to be sure equipment is in safe
working condition.
b) Apply oil at all pivot points.
DRIVE MECHANISM DISMOUNTING
SEE ATTACHMENT OWNER'S MANUAL
(SNOWBLOWER, BROOM AND BLADE) FOR
DISMOUNTING INSTRUCTIONS.
a) Dismount the attachment.
b) Remove the rear counterweight when you remove
the front attachment.
c) Dismount the drive mechanism by supporting it in
hand and removing the two hair pins and the pins.
Carefully lower to the ground. Remove the V-belt
from engine pulley.
Manual clutch activated by cable:
Unhook cable shield by removing the hair pin.
Unhook spring. Pull out drive mechanism from
underneath tractor.
d) You may leave the subframe on tractor all year long
or remove it if preferred.
e) Reinstall mower if needed.
BELT REPLACEMENT
Drive Mechanism Belt:
Dismount the drive mechanism.
Remove the bolt which retains the tension pulley.
Replace the belt and re-install the tension pulley.
Before tightening make sure the belt guide does not
touch the belt at any time. Re-install the drive
mechanism.
Manual Clutch:
With the engine stopped, engaged and disengage
the clutch and make sure the belt does not come
into contact with the belt guide.
Electric Clutch:
Make sure the belt does not come into contact with
the belt guide.
END OF SEASON STORAGE
a) Clean and paint all parts from which paint has
worn.
b) Apply oil at all pivot points.
c) Inspect and replace all defective parts before
using again.
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
Bercomac 700382 700384 Manuel utilisateur
- Catégorie
- Tondeuses à gazon
- Taper
- Manuel utilisateur
- Ce manuel convient également à
dans d''autres langues
- English: Bercomac 700382 700384 User manual
Documents connexes
-
Bercomac C151 61580 0 Manuel utilisateur
-
-
-
-
-
-
-
-
-
