Important safety instructions
When using your telephone equipment, basic safety
precautions should always be followed to reduce the risk of
fire, electric shock and injury, including the following:
1. Read and understand all instructions.
2. Follow all warnings and instructions marked on the
product.
3. Unplug this product from the wall outlet before
cleaning. Do not use liquid or aerosol cleaners. Use a
damp cloth for cleaning.
4. CAUTION: Do not install the telephone base at a
height above 2 meters.
5. Do not use this product near water such as near a
bath tub, wash bowl, kitchen sink, laundry tub or a
swimming pool, nor in a wet basement or shower.
6. Do not place this product on an unstable table, shelf,
stand or other unstable surfaces.
7. Avoid placing the telephone system in places with
extreme temperature, direct sunlight, or other
electrical devices. Protect your phone from moisture,
dust, corrosive liquids and fumes.
8. Slots and openings in the back or bottom of the
telephone base and handset are provided for
ventilation. To protect them from overheating,
these openings must not be blocked by placing the
product on a soft surface such as a bed, sofa or rug.
This product should never be placed near or over a
radiator or heat register. This product should not be
placed in any area where proper ventilation is not
provided.
9. This product should be operated only from the type
of power source indicated on the marking label. If you
are not sure of the type of power supply in your home
or office, consult your dealer or local power company.
10. Do not allow anything to rest on the power cord.
Do not install this product where the cord may be
walked on.
11. Never push objects of any kind into this product
through the slots in the telephone base or handset
because they may touch dangerous voltage points or
create a short circuit. Never spill liquid of any kind on
the product.
12. To reduce the risk of electric shock, do not disassemble
this product, but take it to an authorized service facility.
Opening or removing parts of the telephone base or
handset other than specified access doors may expose
you to dangerous voltages or other risks. Incorrect
reassembling can cause electric shock when the
product is subsequently used.
13. Do not overload wall outlets and extension cords.
14. Unplug this product from the wall outlet and refer
servicing to an authorized service facility under the
following conditions:
• When the power supply cord or plug is damaged
or frayed.
• If liquid has been spilled onto the product.
• If the product has been exposed to rain or water.
• If the product does not operate normally by
following the operating instructions. Adjust only
those controls that are covered by the operation
instructions. Improper adjustment of other
controls may result in damage and often requires
extensive work by an authorized technician to
restore the product to normal operation.
• If the product has been dropped and the
telephone base and/or handset has been
damaged.
• If the product exhibits a distinct change in
performance.
15. Avoid using a telephone (other than cordless) during
an electrical storm. There is a remote risk of electric
shock from lightning.
16. Do not use the telephone to report a gas leak in the
vicinity of the leak. Under certain circumstances, a
spark may be created when the adapter is plugged
into the power outlet, or when the handset is
replaced in its cradle. This is a common event
associated with the closing of any electrical circuit.
The user should not plug the phone into a power
outlet, and should not put a charged handset into
the cradle, if the phone is located in an environment
containing concentrations of flammable or
flame-supporting gases, unless there is adequate
ventilation. A spark in such an environment could
create a fire or explosion. Such environments might
include: medical use of oxygen without adequate
ventilation; industrial gases (cleaning solvents;
gasoline vapors; etc.); a leak of natural gas; etc.
17. Only put the handset of your telephone next to your
ear when it is in normal talk mode.
18. The power adapter is intended to be correctly
oriented in a vertical or floor mount position. The
prongs are not designed to hold the plug in place if it
is plugged into a ceiling, under-the-table or cabinet
outlet.
19. For pluggable equipment, the socket-outlet shall
be installed near the equipment and shall be easily
accessible.
20. CAUTION: Use only the batteries
indicated in this manual. There may be a risk of
explosion if a wrong type of battery is used for the
handset. Use only the supplied rechargeable
batteries or replacement batteries (BT162342/
BT262342) for the handset. Do not dispose of
batteries in a fire. They may explode.
21. Use only the adapter included with this product.
Incorrect adapter polarity or voltage can seriously
damage the product.
SAVE THESE INSTRUCTIONS
Battery
• CAUTION: Use Only Supplied Battery.
• Do not dispose of the battery in a fire. Check with
local waste management codes for special disposal
instructions.
• Do not open or mutilate the battery. Released
electrolyte is corrosive and may cause burns or injury
to the eyes or skin. The electrolyte may be toxic if
swallowed.
• Exercise care in handling batteries in order not to
create a short circuit with conductive materials.
• Charge the battery provided with this product only
in accordance with the instructions and limitations
specified in this manual.
Precautions for users of implanted cardiac pacemakers
Cardiac pacemakers (applies only to digital cordless
telephones):
Wireless Technology Research, LLC (WTR), an independent
research entity, led a multidisciplinary evaluation of the
interference between portable wireless telephones and
implanted cardiac pacemakers. Supported by the U.S.
Food and Drug Administration, WTR recommends to
physicians that:
Pacemaker patients
• Should keep wireless telephones at least six inches
from the pacemaker.
• Should NOT place wireless telephones directly over
the pacemaker, such as in a breast pocket, when it is
turned ON.
• Should use the wireless telephone at the ear opposite
the pacemaker.
WTR’s evaluation did not identify any risk to bystanders with
pacemakers from other persons using wireless telephones.
About cordless telephones
• Privacy: The same features that make a cordless
telephone convenient create some limitations.
Telephone calls are transmitted between the
telephone base and the cordless handset by radio
waves, so there is a possibility that the cordless
telephone conversations could be intercepted
by radio receiving equipment within range of the
cordless handset. For this reason, you should not
think of cordless telephone conversations as being as
private as those on corded telephones.
• Electrical power: The telephone base of this cordless
telephone must be connected to a working electrical
outlet. The electrical outlet should not be controlled
by a wall switch. Calls cannot be made from the
cordless handset if the telephone base is unplugged,
switched off or if the electrical power is interrupted.
• Potential TV interference: Some cordless telephones
operate at frequencies that may cause interference
to televisions and VCRs. To minimize or prevent such
interference, do not place the telephone base of the
cordless telephone near or on top of a TV or VCR.
If interference is experienced, moving the cordless
telephone farther away from the TV or VCR often
reduces or eliminates the interference.
• Rechargeable batteries: Exercise care in handling
batteries in order not to create a short circuit with
conducting material such as rings, bracelets and keys.
The battery or conductor may overheat and cause
harm. Observe proper polarity between the battery
and the battery charger.
• Nickel-metal hydride rechargeable batteries: Dispose
of these batteries in a safe manner. Do not burn or
puncture the battery. Like other batteries of this type,
if burned or punctured, they could release caustic
material which could cause injury.
What’s in the box Add & Register a handsetConnect & Activate | Set Date & Time
Need help?
1 set for DS6401, DS6401-15,
DS6401-16
Install and charge the battery
2
a b
c d
16 hrs
Charge the battery
Once you have installed the battery, the handset
LCD display indicates the battery status (see the
table below).
Battery
indicators
Battery status Action
The screen
is blank or
shows Put in
charger and
flashes.
Battery has no
charge or very little
charge. The
handset cannot
be used.
Charge
without
interruption
(at least 30
minutes).
The screen
shows
Low battery
and
flashes.
Battery has enough
charge
to be used for a
short time.
Charge
without
interruption
(at least 30
minutes).
The screen
shows
HANDSET X.
Battery is charged.
To keep
the battery
charged,
place it in the
telephone
base
or charger
when not in
use.
When it is fully charged, you can expect the
following performance:
Operation Operating time
While in handset use
(talking*) 7 hours
While in speakerphone
mode (talking*) 5 hours
While not in use
(standby**) 7 days
* Operating times vary depending on your actual
use and the age of the battery.
** Handset is not charging or in use.
NOTES
• Place the handset in the charger will bypass the
set date and time, and voice guide.
• For best performance, keep the handset in the
charger when not in use.
• The battery is fully charged after 16 hours of
continuous charging.
• If you place the handset in the charger without
plugging in the battery, the screen displays
NO BATTERY.
After you install
your telephone
or power returns
following a power
outage and
battery depletion,
the handset will
prompt you to set
the date and time.
Press OFF/ CANCEL
or [BACK].
SET DATE
09/30/14
MM/DD/YY
BACK
SET
handset... on the handset and the red IN USE
light on the telephone base turns on. It takes
about
90 seconds to complete the registration
process. The handset displays HANDSET
X Registered (X represents the registered
handset number). The IN USE light on the
telephone base turns off and you hear a
confirmation tone from the handset when
registration completes.
If registration fails, the system will automatically
try to register again.
If registration fails after the third try, the handset
displays Registration failed, and then Put handset
on BASE to register and the telephone base
beeps. This may take up to five minutes to occur.
To reset the handset, remove it from the
telephone base. When the handset displays Put
handset on BASE to register, try the registration
process again.
NOTE
• You cannot register a handset if any other
system handset is in use.
You can add new handsets (DS6401/DS6401-
15/DS6401-16, purchased separately) to
your DS6421/DS6472 telephone system,
but each handset must be registered with
the telephone base before use. When first
purchased, each expansion handset shows
Put handset on BASE to register after a
battery is installed. You may need to charge
the handset before registering it to the
telephone base.
To register a handset
1. Make sure the handset is out of the
telephone base or handset charger and
shows Put handset on BASE to register.
Place the handset in the telephone base.
2. The handset displays Registering
For operations and guides to help you using your telephone, and for latest information and
supports, go and check the online help topics and online FAQs.
Use your smartphone or mobile device to access our online help.
• Go to https://help.vtechphones.com/DS6401; OR
• Scan the QR code on the right. Launch the camera app or QR code scanner app on your
smartphone or tablet. Hold the device’s camera up to the QR code and frame it. Tap the
notification to trigger the redirection of the online help.
If the QR code is not clearly displayed, adjust your camera’s focus by moving your device closer or
further away until it is clear.
You can also call our Customer Support at 1 (800) 595-9511 [in US] or
1 (800) 267-7377 [in Canada] for help.
S
m
Go to
www.vtechphones.com
to register your product for
enhanced warranty support
and latest VTech product
news.
DS6401
DS6401-15
DS6401-16
Accessory handset for
DS6421 / DS6472
User’s Manual
Specifications are subject to change without notice.
© 2021 VTech Communications, Inc.
All rights reserved. 03/21. DS6401-X_UM_V1.0
T
Compatible with
Hearing Ai
d T-Coil
TIA-1083
Telephones identified with this logo have reduced noise and interference when used with most T-coil equipped hearing
aids and cochlear implants. The TIA-1083 Compliant Logo is a trademark of the Telecommunications Industry Association.
Used under license.
The ENERGY STAR® program (www.energystar.gov) recognizes and encourages the use of products that save energy and
help protect our environment. We are proud to mark this product with the ENERGY STAR® label indicating it meets the latest
energy efficiency guidelines.
S
m
For more support information
Deregister handsets Operating range
Maintenance
For C-UL compliance only
Mesures de sécurité importantes
Afin de réduire les risques d’incendie, de blessures
corporelles ou d’électrocution, suivez toujours ces mesures
préventives de base lorsque vous utilisez votre téléphone :
1. Lisez et comprenez bien toutes les instructions.
2. Observez toutes les instructions et mises en garde inscrites
sur l’appareil.
3. Débranchez ce téléphone de la prise murale avant de le
nettoyer. N’utilisez pas de nettoyeurs liquides ni en aérosol.
N’utilisez qu’un chiffon doux et légèrement humecté.
4. ATTENTION: Ne pas installer le socle téléphonique à une
hauteur supérieure à 2 mètres.
5. N’utilisez pas ce produit près de l’eau, tel que près d’un
bain, d’un lavabo, d’un évier de cuisine, d’un bac de
lavage ou d’une piscine, ou dans un sous-sol humide
ou sous la douche.
6. Ne déposez pas ce téléphone sur un chariot, support
ou table chancelants. L’appareil pourrait tomber et être
sérieusement endommagé.
7. Évitez d’installer le système téléphonique dans les endroits
soumis à une température extrême, à la lumière directe
du soleil ou à proximité immédiate d’autres appareils
électriques ou électroniques. Protégez votre téléphone
contre les sources d’humidité, la poussière, les vapeurs et
les liquides corrosifs.
8. Le boîtier de l’appareil est doté de fentes et d’ouvertures
d’aération situées à l’arrière ou en dessous. Afin
d’empêcher la surchauffe, ces ouvertures ne doivent
pas être obstruées en plaçant l’appareil sur un lit,
divan, tapis ou autre surface similaires. Ne placez pas
cet appareil à proximité d’un élément de chauffage ni
d’une plinthe électrique. De plus, ne l’installez pas dans
une unité murale ou un cabinet fermé qui ne possède
pas d’aération adéquate.
9. Ne faites fonctionner cet appareil qu’avec le type
d’alimentation indiqué sur les étiquettes de l’appareil.
Si vous ne connaissez pas le voltage de votre maison,
consultez votre marchand ou votre fournisseur d’électricité.
10. Ne déposez rien sur le cordon d’alimentation. Installez
cet appareil dans un endroit sécuritaire, là où personne
ne pourra trébucher sur la ligne d’alimentation ni le
cordon téléphonique modulaire.
11. N’insérez jamais d’objets à travers les fentes et
ouvertures de cet appareil, car ils pourraient toucher
à des points de tension dangereux ou court-circuiter
des pièces, ce qui constituerait un risque d’incendie
ou d’électrocution. N’échappez pas de liquides
dans l’appareil.
12. Afin de réduire les risques d’électrocution, ne démontez
pas l’appareil, mais apportez-le plutôt à un centre
de service qualifié s’il doit être réparé. En enlevant
le couvercle, vous vous exposez à des tensions
dangereuses ou autres dangers similaires. Un
remontage inadéquat peut être à l’origine d’une
électrocution lors d’une utilisation ultérieure de
l’appareil. Débranchez l’appareil avant de procéder
au nettoyage. Utilisez un chiffon humide et doux.
13. Ne surchargez pas les prises de courant et les rallonges.
14. Débranchez cet appareil de la prise de courant et
communiquez avec le département de service à la
clientèle de VTech dans les cas suivants :
• Lorsque le cordon d’alimentation est endommagé
ou écorché.
• Si du liquide a été échappé dans l’appareil.
• Si l’appareil a été exposé à une source d’humidité telle
que la pluie ou l’eau.
• Si le produit ne fonctionne pas normalement en
respectant les instructions de fonctionnement. Réglez
uniquement les commandes indiquées dans le les
instructions de fonctionnement. Les réglages incorrects
des autres commandes pourraient provoquer un
dommage qui pourrait exiger un travail exhaustif
de la part d’un technicien autorisé afin de rétablir le
fonctionnement normal de l’appareil.
• Si le produit a été échappé et que le socle et/ou le
combiné a été endommagé.
• Si le produit affiche une nette diminution de sa
performance.
15. Évitez d’utiliser un téléphone (autre qu’un sans fil)
pendant un orage. Les éclairs peuvent être à l’origine
d’une électrocution.
16. N’utilisez pas le téléphone pour rapporter une fuite de
gaz à proximité de la fuite. En certaines circonstances,
une flammèche pourrait être provoquée lorsque
l’adaptateur est branché à une prise de courant, ou
lorsque le combiné est déposé sur le socle. Ceci
est un événement commun associé à la fermeture
d’un circuit électrique. L’utilisateur ne devrait pas
brancher le téléphone à une prise de courant, et ne
devrait pas déposer le combiné chargé sur le socle,
si le téléphone se trouve à proximité d’un endroit
comportant des concentrations de gaz inflammables,
à moins que la ventilation soit adéquate. Une
flammèche dans un tel endroit pourrait provoquer un
incendie ou une explosion. De tels environnements
peuvent comprendre: des endroits où l’on utilise de
l’oxygène médical sans ventilation adéquate; des gaz
industriels (dissolvants de nettoyage, des vapeurs
d’essence, etc.); une fuite de gaz naturel, etc.
17. Ne placez que le combiné de votre téléphone près de
votre oreille lorsqu’en mode de conversation.
18. Ces adaptateurs ont été conçus pour être orientés en
position verticale ou montés au sol. Les broches ne
sont pas conçues pour maintenir l’adaptateur en place
si celui-ci est barnché dans une prise au plafond ou sous
une table/ armoire.
19. Pour le MATERIEL RACCORDE PAR PRISE DE COURANT,
le socle de prise de courant doit etre installe a proximite
du materiel et doit etre aisement accessible.
20. MISE EN GARDE: Il peut y avoir un risque
d’explosion si vous utilisez le mauvais type de piles
pour le téléphone. N’utilisez que les piles
rechargeable inclus ou les piles de rechange
(BT162342/BT262342). N’incinérez pas les piles. Celles-
ci risqueraient d’exploser.
21. N’utilisez que les adaptateurs inclus avec ce produit.
L’utilisation d’un adaptateur dont la polarité ou la
tension serait inadéquate risque d’endommager
sérieusement le produit et mettre votre sécurité en
péril.
CONSERVEZ CES INSTRUCTIONS
Pile
• N’utilisez que la pile incluse ou l’équivalent.
• Ne jetez pas la pile au feu. Vérifiez les instructions
spécifiques de mise aux rebus auprès des autorités
locales.
• N’ouvrez pas et ne mutilez pas la pile. L’électrolyte qui s’en
échapperait est corrosif et pourrait causer des brûlures
ou des blessures aux yeux ou à la peau. L’électrolyte
est toxique si avalé.
• Soyez prudents lorsque vous manipulez les piles afin
d’éviter les courts-circuits provoqués par des matériaux
conducteurs.
• Rechargez la pile incluse avec cet appareil, selon
les instructions et limites spécifiées dans ce guide
d’utilisation.
Stimulateurs cardiaques implantés dans l’organisme
Les simulateurs cardiaques (s’applique uniquement aux
téléphones numériques sans fil) :
L’organisme ‘Wireless Technology Research, LLC (W TR)’, une
firme de recherche indépendante, a mené une évaluation
pluridisciplinaire des interférences entre les téléphones sans
fil portatifs et les stimulateurs cardiaques implantés dans
l’organisme. Appuyée par l’Administration des aliments et
drogues (FDA) des États-Unis, la firme WTR recommande
aux médecins :
Avis aux détenteurs de stimulateurs cardiaques
• Ils doivent tenir le téléphone sans fil à une distance d’au
moins six pouces du stimulateur cardiaque.
• Ils ne doivent PAS placer le téléphone sans fil directement
sur le stimulateur cardiaque, tel que dans une poche de
chemise, lorsque celui-ci est en marche.
• Ils doivent utiliser le téléphone sans fil en l’appuyant
sur l’oreille qui se trouve dans la direction opposée au
stimulateur cardiaque.
L’étude effectuée par l’organisme WRS n’a pas identifié
de risque pour les détenteurs de simulateurs cardiaques
causés par les gens qui utilisent un téléphone sans fil à
proximité de ceux-ci.
À propos des téléphones sans fil
Confidentialité : Les mêmes caractéristiques qui constituent
des avantages pour les téléphones sans fil affichent
également des restrictions. Les appels téléphoniques
sont transmis entre le combiné sans fil et le socle par
le biais d’ondes radio ; il y a donc la possibilité que vos
conversations téléphoniques sans fil soient interceptées
par des équipements de réception radio se trouvant dans
la portée du combiné sans fil. Pour cette raison, vous ne
devez pas percevoir les communications téléphoniques
sans fil comme étant aussi confidentielles que celles des
téléphones à cordons.
Alimentation électrique : Le socle de ce téléphone sans fil
doit être branché à une prise électrique fonctionnelle. La
prise électrique ne doit pas être contrôlée par un interrupteur
mural. Les appels ne pourront pas être effectués du combiné
sans fil si le socle est débranché ou mis hors tension ou si le
courant est coupé.
Possibilité d’interférences aux téléviseurs : Certains
téléphones sans fil fonctionnent sur des fréquences
pouvant causer des interférences aux téléviseurs et
aux magnétoscopes. Pour réduire ou prévenir de telles
interférences, ne placez pas le socle du téléphone sans fil
près ou sur un téléviseur ou magnétoscope. S’il y a présence
de parasites, il est conseillé d’éloigner le téléphone sans fil du
téléviseur ou du magnétoscope afin de réduire possiblement
les interférences.
Piles rechargeables : Manipulez les piles avec soin afin de
ne pas les court-circuiter avec des bagues, bracelets ou
clés. Les piles ou le conducteur peut surchauffer et causer
des blessures. Respectez la polarité adéquate entre la pile
et le chargeur.
Les bloc-piles rechargeables à l’hydrure métallique de
nickel : Jetez ces blocs-piles de manière écologique
et sécuritaire. Ne les incinérez pas et ne les percez pas.
Tel que les autres piles de ce type, elles pourraient
dégager une matière toxique qui peut causer
des blessures corporelles si elles sont brûlées ou percées.
The RBRC® Seal
The RBRC seal on the nickel-metal hydride battery indicates
that VTech Communications, Inc. is voluntarily participating in
an industry program to collect and recycle
these batteries at the end of their useful lives,
when taken out of service within the United
States and Canada.
The RBRC program provides a convenient
alternative to placing used nickel-metal
hydride batteries into the trash or municipal
waste, which may be illegal in your area.
VTech’s participation in RBRC makes it easy for
you to drop off the spent battery at local retailers
participating in the RBRC program or at authorized
VTech product service centers. Please call
1 (800) 8 BATTERY® for information on Ni-MH battery
recycling and disposal bans/restrictions in your area. VTech’s
involvement in this program is part of its commitment to
protecting our environment and conserving natural resources.
The RBRC Seal and 1 (800) 8 BATTERY® are registered
trademarks of Call2recycle, Inc.
FCC, ACTA and IC regulations
FCC Part 15
NOTE: This equipment has been tested and found to
comply with the requirements for a Class B digital device
under Part 15 of the Federal Communications Commission
(FCC) rules. These requirements are intended to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause
harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment
and receiver.
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV
technician for help.
WARNING: Changes or modifications to this equipment
not expressly approved by the party responsible for
compliance could void the user’s authority to operate
the equipment.
This device complies with Part 15 of the FCC rules.
Operation is subject to the following two conditions: (1)
this device may not cause harmful interference, and (2) this
device must accept any interference received, including
interference that may cause undesired operation. Privacy
of communications may not be ensured when using this
telephone.
To ensure safety of users, the FCC has established criteria
for the amount of radio frequency energy that can be
safely absorbed by a user or bystander according to the
intended usage of the product. This product has been
tested and found to comply with the FCC criteria. The
handset may be safely held against the ear of the user. The
telephone base shall be installed and used such that parts
of the user’s body other than the hands are maintained at a
distance of approximately 20 cm (8 inches) or more.
This Class B digital apparatus complies with Canadian
requirement:
CAN ICES-3 (B)/NMB-3(B).
FCC Part 68 and ACTA
This equipment complies with Part 68 of the FCC rules and
with technical requirements adopted by the Administrative
Council for Terminal Attachments (ACTA). The label
on the back or bottom of this equipment contains,
among other things, a product identifier in the format
US:AAAEQ##TXXXX. This identifier must be provided to
your telephone service provider upon request.
The plug and jack used to connect this equipment to
premises wiring and the telephone network must comply
with applicable Part 68 rules and technical requirements
adopted by ACTA. A compliant telephone cord and
modular plug is provided with this product. It is designed
to be connected to a compatible modular jack that is
also compliant. An RJ11 jack should normally be used for
connecting to a single line and an RJ14 jack for two lines.
See the installation instructions in the user’s manual.
The Ringer Equivalence Number (REN) is used to
determine how many devices you may connect to your
telephone line and still have them ring when you are
called. The REN for this product is encoded as the 6th
and 7th characters following the US: in the product
identifier (e.g., if ## is 03, the REN is 0.3). In most, but not
all areas, the sum of all RENs should be five (5.0) or less.
For more information, please contact your telephone
service provider.
This equipment must not be used with Party Lines. If you
have specially wired alarm dialing equipment connected
to your telephone line, ensure the connection of this
equipment does not disable your alarm equipment.
If you have questions about what will disable alarm
equipment, consult your telephone service provider or a
qualified installer.
If this equipment is malfunctioning, it must be unplugged
from the modular jack until the problem has been
corrected. Repairs to this telephone equipment can only
be made by the manufacturer or its authorized agents. For
repair procedures, follow the instructions outlined under
the Limited warranty.
If this equipment is causing harm to the telephone
network, the telephone service provider may temporarily
discontinue your telephone service. The telephone service
provider is required to notify you before interrupting
service. If advance notice is not practical, you will be
notified as soon as possible. You will be given the opportunity to correct
the problem and the telephone service provider is required to inform
you of your right to file a complaint with the FCC. Your telephone service
provider may make changes in its facilities, equipment, operation, or
procedures that could affect the proper functioning of this product.
The telephone service provider is required to notify you if such changes
are planned.
If this product is equipped with a corded or cordless handset, it is hearing
aid compatible.
If this product has memory dialing locations, you may choose to store
emergency telephone numbers (e.g., police, fire, medical) in these
locations. If you do store or test emergency numbers, please:
Remain on the line and briefly explain the reason for the call before
hanging up.
Perform such activities in off-peak hours, such as early morning or late
evening.
Industry Canada
This device contains licence-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada’s licence-
exempt RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may
cause undesired operation of the device.
Privacy of communications may not be ensured when using this telephone.
The term ‘’IC:‘’ before the certification/registration number only signifies
that the Industry Canada technical specifications were met.
The Ringer Equivalence Number (REN) for this terminal equipment is
1.0. The REN indicates the maximum number of devices allowed to be
connected to a telephone interface. The termination of an interface may
consist of any combination of devices subject only to the requirement that
the sum of the RENs of all the devices not exceed five.
This product meets the applicable Innovation, Science and
Economic Development Canada technical specifications.
California Energy Commission
battery charging testing
instructions
This telephone is set up to comply with the energy-conserving standards right
out of the box. These instructions are intended for California Energy Commission
(CEC) compliance testing only. When the CEC battery charging testing mode
is activated, all telephone functions, except battery charging, will be disabled.
To activate the CEC battery charging testing mode:
1. Unplug the telephone base power adapter from the power outlet. Make
sure all handsets are plugged with charged batteries before proceeding.
2. While you press and hold /FIND HANDSET, plug the telephone base
power adapter back to the power outlet.
3. After about 20 seconds, when the IN USE light starts flashing, release /
FIND HANDSET and then press it again within 2 seconds.
When the phone successfully enters the CEC battery charging testing mode,
the IN USE light turns off and all handsets display Put handset on BASE to
register.
When the phone fails to enter this mode, repeat Step 1 through Step 3 above.
Note: The telephone base will be powered up as normal if you fail to press /
FIND HANDSET within 2 seconds in Step 3.
To deactivate the CEC battery charging testing mode:
1. Unplug the telephone base power adapter from the power outlet, then
plug it back in. Then, the telephone base is powered up as normal.
2. Register your handsets back to the telephone base. See handset
registration instructions.
Limited Warranty
What does this limited warranty cover?
The manufacturer of this VTech Product warrants to the holder of a valid
proof of purchase (“Consumer” or “you”) that the Product and all accessories
provided in the sales package (“Product”) are free from defects in material and
workmanship, pursuant to the following terms and conditions, when installed
and used normally and in accordance with the Product operating instructions.
This limited warranty extends only to the Consumer for Products purchased
and used in the United States of America and Canada.
What will VTech do if the Product is not free from defects in materials and
workmanship during the limited warranty period (“Materially Defective
Product”)?
During the limited warranty period, VTech’s authorized service representative
will repair or replace at VTech’s option, without charge, a Materially Defective
Product. If we repair the Product, we may use new or refurbished replacement
parts. If we choose to replace the Product, we may replace it with a new or
refurbished Product of the same or similar design. We will retain defective
parts, modules, or equipment. Repair or replacement of the Product, at
VTech’s option, is your exclusive remedy. VTech will return the repaired or
replacement Products to you in working condition. You should expect the
repair or replacement to take approximately 30 days.
How long is the limited warranty period?
The limited warranty period for the Product extends for ONE (1) YEAR from the
date of purchase. If VTech repairs or replaces a Materially Defective Product
under the terms of this limited warranty, this limited warranty also applies to
the repaired or replacement Product for a period of either (a) 90 days from
the date the repaired or replacement Product is shipped to you or (b) the time
remaining on the original one-year warranty; whichever is longer.
What is not covered by this limited warranty?
This limited warranty does not cover:
Product that has been subjected to misuse, accident, shipping or other physical
damage, improper installation, abnormal operation or handling, neglect,
inundation, fire, water or other liquid intrusion.
Product that has been subjected to contact with liquid, water, rain, extreme
humidity or heavy perspiration, sand, dirt or the like; but then only to the extent
the damage was not caused by incorrectly securing the waterproof handset’s
protective elements, for example, failing to properly close a seal), or such
protective elements are damaged or missing (e.g. a cracked battery door),
or subjecting a Product to conditions beyond its stated specifications or limits
(e.g. 30 minutes in 1 meter of fresh water).
Product that has been damaged due to repair, alteration or modification by
anyone other than an authorized service representative of VTech;
Product to the extent that the problem experienced is caused by signal
conditions, network reliability, or cable or antenna systems;
Product to the extent that the problem is caused by use with non-VTech
accessories;
Product whose warranty/quality stickers, product serial number plates or
electronic serial numbers have been removed, altered or rendered illegible;
Product purchased, used, serviced, or shipped for repair from outside the
United States of America or Canada, or used for commercial or institutional
purposes (including but not limited to Products used for rental purposes);
Product returned without a valid proof of purchase (see item 2 below); or
Charges for installation or set up, adjustment of customer controls, and
installation or repair of systems outside the unit.
How do you get warranty service?
To obtain warranty service in the United States of America, please visit our
website at
www.vtechphones.com or call 1 (800) 595-9511. In Canada, go to phones.
vtechcanada.com or dial 1 (800) 267-7377.
NOTE: Before calling for service, please review the user’s manual - a check of
the Product’s controls and features may save you a service call.
Except as provided by applicable law, you assume the risk of loss or damage
during transit and transportation and are responsible for delivery or handling
charges incurred in the transport of the Product(s) to the service location.
VTech will return repaired or replaced Product under this limited warranty.
Transportation, delivery or handling charges are prepaid. VTech assumes no
risk for damage or loss of the Product in transit. If the Product failure is not
covered by this limited warranty, or proof of purchase does not meet the terms
of this limited warranty, VTech will notify you and will request that you authorize
the cost of repair prior to any further repair activity. You must pay for the cost of
repair and return shipping costs for the repair of Products that are not covered
by this limited warranty.
What must you return with the Product to get warranty service?
1. Return the entire original package and contents including the Product to
the VTech service location along with a description of the malfunction or
difficulty; and
2. Include a “valid proof of purchase” (sales receipt) identifying the Product
purchased (Product model) and the date of purchase or receipt; and
3. Provide your name, complete and correct mailing address, and
telephone number.
Other limitations
This warranty is the complete and exclusive agreement between you and
VTech. It supersedes all other written or oral communications related to this
Product. VTech provides no other warranties for this Product. The warranty
exclusively describes all of VTech’s responsibilities regarding the Product.
There are no other express warranties. No one is authorized to make
modifications to this limited warranty and you should not rely on any such
modification.
State/Provincial Law Rights: This warranty gives you specific legal rights, and
you may also have other rights, which vary from state to state or province to
province.
Limitations: Implied warranties, including those of fitness for a particular
purpose and merchantability (an unwritten warranty that the Product is fit for
ordinary use) are limited to one year from the date of purchase. Some states/
provinces do not allow limitations on how long an implied warranty lasts, so
the above limitation may not apply to you. In no event shall VTech be liable for
any indirect, special, incidental, consequential, or similar damages (including,
but not limited to lost profits or revenue, inability to use the Product or other
associated equipment, the cost of substitute equipment, and claims by third
parties) resulting from the use of this Product. Some states/provinces do not
allow the exclusion or limitation of incidental or consequential damages, so the
above limitation or exclusion may not apply to you.
Please retain your original sales receipt as proof of purchase
Disclaimer and Limitation of Liability
VTech Communications, Inc. and its suppliers assume no responsibility
for any damage or loss resulting from the use of this user’s manual. VTech
Communications, Inc. and its suppliers assume no responsibility for any loss or
claims by third parties that may arise through the use of this product.
Company: VTech Communications, Inc.
Address: 9020 SW Washington Square Road - Ste 555 Tigard, OR 97223, United
States
Phone: 1 (800) 595-9511 in the U.S. or 1 (800) 267-7377 in Canada
If you want to replace a handset or reassign the
designated handset number of a registered
handset, you must deregister all handsets.
Then register each handset you wish to use
individually.
To make deregistration easier, read all of the
instructions on this page before you begin.
To deregister all handsets
1. Make sure that all handsets are out of the
telephone base and handset chargers
before you begin deregistration.
2. Press and hold /FIND HANDSET on the
telephone base for about 10 seconds until
the IN USE light flashes.
3. Quickly press /FIND HANDSET again. You
must press /FIND HANDSET while the IN
USE light is still flashing. The IN USE light
flashes for about five seconds. If the light
stops flashing, start again with Step 1 above.
4. All system handsets show Put handset on
BASE to register, and you hear a confirmation
tone when deregistration completes. The
deregistration process takes about 10
seconds to complete.
If deregistration fails, you may need to reset the
telephone and try again.
To reset
• Press and hold OFF/CANCEL or place the
handset back in the telephone base.
- OR -
• Unplug the power from the telephone base,
then plug it back in.
NOTES
• You cannot deregister handsets if any system
handset is in use.
• Even if the battery is depleted, you can still
deregister the handsets by following the
steps above.
Taking care of your telephone
Your cordless telephone contains sophisticated
electronic parts, so it must be treated with care.
Avoid rough treatment
Place the handset down gently. Save the original
packing materials to protect your telephone if
you ever need to ship it.
Avoid water
Your telephone can be damaged if it gets wet.
Do not use the handset outdoors in the rain,
or handle it with wet hands. Do not install the
telephone base near a sink, bathtub or shower.
Electrical storms
Electrical storms can sometimes cause power
surges harmful to electronic equipment. For your
own safety, take caution when using electrical
appliances during storms.
Cleaning your telephone
Your telephone has a durable plastic casing that
should retain its luster for many years. Clean it
only with a soft cloth slightly dampened with
water or mild soap. Do not use excess water or
cleaning solvents of any kind.
NOTES
• Remember that electrical appliances can cause
serious injury if used when you are wet or
standing in water.
• If the telephone base should fall into water,
DO NOT RETRIEVE IT UNTIL YOU UNPLUG
THE POWER CORD AND TELEPHONE LINE
CORD FROM THE WALL. Then, remove the
telephone by the unplugged cords.
This cordless telephone operates with the
maximum power allowed by the Federal
Communications Commission (FCC). Even so, this
handset and telephone base can communicate
over only a certain distance - which can vary
with the locations of the telephone base and
handset, the weather, and the layout of your
home or office.
When the handset is out of range, the handset
displays Out of range OR No power at base.
If there is a call while the handset is out of range,
it might not ring, or if it does ring, the call might
not connect well when you press /HOME/
FLASH. Move closer to the telephone base, then
press /HOME/FLASH to answer the call.
If the handset moves out of range during
a telephone conversation, there might be
interference.
To improve reception, move closer to the
telephone base.
Frequency control Crystal controlled PLL synthesizer
Transmit frequency Telephone Base | Handset: 1921.536-
1928.448 MHz
Channels DECT channel: 5
Nominal effective range Maximum power allowed by FCC and
IC. Actual operating range may vary
according to environmental conditions at
the time of use.
Power requirement Handset: 2.4V Ni-MH battery | Charger:
6V DC @ 400mA
Memory Directory: 200 memory locations; up to
30 digits and 15 characters
Four download directories: 1,500
memory locations (each); up to 30 digits
and 15 characters
Caller ID log: 50 memory locations; up to
15 digits and 15 characters
Technical specification
-
1
-
2
VTech Accessory Handset Manuel utilisateur
- Taper
- Manuel utilisateur
dans d''autres langues
- English: VTech Accessory Handset User manual