EtherWAN EX87000 Series Quick Installation Guide
- Taper
- Quick Installation Guide
W70G-EX870V2Q3 Page 1
Copyright 2022 EtherWAN Systems, Inc. All Rights Reserved 12/05/2022
Installation Guide
EX87000 Series | Hardened Managed Ethernet Switch
Unpacking
Open the carton and unpack the items. Your package should include:
▪ EX87000 Ethernet switch
▪ Rack mounting brackets
If any items are missing or damaged, notify your EtherWAN representative. If
possible, save the carton and packing material in case you need to ship or store the
switch in the future.
What Else You Need
▪ Appropriate cables for data ports
▪ Personal computer or laptop
Select a Location
▪ Rack installations: Use a 19-inch (48.3-centimeter) EIA standard equipment
rack that is grounded and physically secure.
▪ Identify a power source within 6 feet (1.8 meters).
▪ Choose a dry area with ambient temperature between -40 and 75ºC (-40
and 167ºF).
▪ Be sure there is adequate airflow.
Connect to the Data Ports
Depending on the model, your switch can have the following ports:
▪ 0, 8, 16, or 24 10/100Base-TX ports
▪ 0, 8,16, or 24 100Base-FX ports
▪ 4 Gigabit ports
10/100Base-TX and 100Base-FX Ports
These ports come in 10/100Base-TX and 100Base-FX/SFP interfaces. They can
connect to devices such as an IP surveillance camera or a Voice Over Internet
Protocol (VoIP) phone.
Gigabit Ports
Some switch models have 4 1000Base-SX/LX/BX ports, or 4-port 1000Base SFP
combo with 10/100/1000Base-TX ports. You can connect these ports to network
devices such as a computer, printer, network video recorder (NVR), network
storage, or they can connect to the network itself.
Combo ports operate in “either/or” fashion. This means that attaching to a 1
Gbps combo port renders the equivalent partner combo port unavailable.
Apply Power
Terminal Block
If your EX87000 comes with AC power cables, connect the cables into the power
modules at the back of the switch. If your switch comes with a DC or AC terminal
block (no cable), then connect the switch to a suitable power supply using 12 to
18 AWG wire. Redundant power supply is supported. However, only one power
input is required to operate the switch. Input voltage is 48 VDC or 100 – 240 VAC
/ 88-300 VDC, depending on model.
Relay Output Alarm
The switch provides one dry contact for signaling of a user-defined power or port
failure. The alarm relay default is “open” and forms a closed circuit when the
event occurs. The relay output can be connected to an alarm signaling device.
Relay output current is 30VDC / 0.6A.
Power-Up Sequence
When you apply power, all Link/ACT LEDs blink momentarily, the Power LED goes
ON, and LEDs for every port connected to a device flash.
Front Panel LEDs
LED
Color
Status
Power
Green
On: Power on
Off: Power off
Alarm
Red
Link down or power down
10/100Base-TX, 100Base-FX/BX/SFP
Link/Act
Green
On: Network connection established
Flashing: Port sending or receiving data
1000Base-T/SX/LX/SFP
Link/Act
Green
On: Network connection established
Flashing: Port sending or receiving data
Console Configuration
Connect to the switch console by connecting the DB-9 cable to the console port of
the switch and to the serial port of the computer running a terminal emulation
application (such as HyperTerminal or Putty).
Configuration settings of the terminal-emulation program: Baud rate:
115,200bps, Data bits: 8, Parity: none, Stop bit: 1, Flow control: none.
The default login name is root, no password.
Web Configuration
Log in to the switch by launching a web browser and entering 192.168.1.10 in the
address bar. Enter the default login ID: root (no password) and click “Login.”
Other Electrical and Safety Information
(A) Elevated Operating Ambient - If installed in a closed or multi-unit rack
assembly, the operating ambient temperature of the rack environment may be
greater than room ambient. Therefore, consideration should be given to installing
the equipment in an environment compatible with the maximum ambient
temperature (Tma).
B) Mechanical Loading - Mounting of the equipment in the rack should be such
that a hazardous condition is not achieved due to uneven mechanical loading.
C) Circuit Overloading - Consideration should be given to the connection of the
equipment to the supply circuit and the effect that overloading of the circuits
might have on overcurrent protection and supply wiring. Appropriate
consideration of equipment nameplate ratings should be used when addressing
this concern.
D) Reliable Earthing - Reliable earthing of rack-mounted equipment should be
maintained. Particular attention should be given to supply connections other than
direct connections to the branch circuit (e.g. use of power strips).
Do not disable the power cord grounding plug. The grounding plug is an
important safety feature.
Caution:
This equipment shall be used with all power supplies connected simultaneously.
This equipment is intended to be used in a restricted access location and by
qualified personnel. This equipment is not suitable for use in locations where
children are likely to be present.
Hazardous voltages may occur within this unit when connected to
all power supplies. Prevent access to hazardous voltages by disconnecting
this equipment from all power supplies.
Plug the power cord into a grounded (earthed) electrical outlet that
is easily accessible at all times.
W70G-EX870V2Q3 Page 2
Copyright 2022 EtherWAN Systems, Inc. All Rights Reserved 12/05/2022
Installation Guide
EX87000 Series | Hardened Managed Ethernet Switch
Les matériels sont destinés à être installés dans des EMPLACEMENTS À ACCÈS
RESTREINT.
This equipment must be connected to Protective earthing (PE) to AC mains
ground. The protective earthing conductor shall be minimum 18 AWG and having
green-and-yellow insulation. The thread diameter of screw type terminal shall be
minimum 3.5mm.
The ground wire should be installed first (earlier than live and neutral wires) and
then removed. The grounding wire should be longer than live and neutral wires.
When wiring the switch to power, unscrew the two retaining screws that hold the
protective cover in place. The metal protective cover should be reattached after
the wiring is completed to avoid the danger of electric shock.
When stripping the cable sheath for connection to the terminal block, leave only
10mm of wires exposed for the connection.
The power cord shall be IEC 60227 certified, rated 0.75 mm2 x 3C or UL
recognized minimum 18AWG.
Terminal Block:
This product is intended to be supplied by certified DC power source and rated
output rating: 48 VDC, 1 A minimum.
AC Terminal Block
AC power rating current is 0.8A. All power connection wiring by a qualified
electrician in accordance with National Electrical Code, ANSI/NFPA 70 and
Canadian Electrical Code, Part I, CSA C22.1. An IEC certified or UL listed single-
phase type circuit-breaker, rated maximum 20A, shall be installed between mains
circuit and equipment.
Thumbscrews should be tightened with a tool after both initial installation
subsequent access to the panel.
Note:
This equipment must use UL recognized Laser Class 1 optical transceiver.
Manufacturer information:
EtherWAN Systems, Inc.
33F, No. 93, Sec. 1, Xintai 5th Rd., Xizhi Dist., New Taipei City, 221 Taiwan
The full product manual can be downloaded from:
www.etherwan.com
-
1
-
2
EtherWAN EX87000 Series Quick Installation Guide
- Taper
- Quick Installation Guide
dans d''autres langues
- English: EtherWAN EX87000 Series
Documents connexes
-
EtherWAN EX27000 Series Quick Installation Guide
-
EtherWAN EX71000 Series Quick Installation Guide
-
EtherWAN EX61000A Series Quick Installation Guide
-
EtherWAN IG5 Rack Series Quick Installation Guide
-
EtherWAN EG97023 Series Quick Installation Guide
-
EtherWAN OttoE Series Quick Installation Guide
-
EtherWAN OttoE PoE Series Quick Installation Guide
