VTech CS6120-2 Manuel utilisateur

Marque: VTech

Modèle: CS6120-2

Catégorie: Téléphones

Taper: Manuel utilisateur

What’s in the box

Your telephone package contains the following

items. Save your sales receipt and original

packaging in the event warranty service is

necessary.

Telephone base overview

1 – /REPEAT

• Repeat a message.

• Press twice to play the previous message.

2 – /SKIP

• Skip to the next message.

3 – /FIND HANDSET

• Page all system handsets.

4 – Charging pole

5 – Speakerphone

6 – X/DELETE

• Delete the playing message.

• Press twice to delete all old messages.

7 – Message window

8 – /PLAY/STOP

• Play messages.

• Stop playing messages.

9 – p/q/VOLUME

• Adjust the listening volume.

• Adjust the telephone base ringer volume.

10 – /ANS ON/OFF

• Turn on or off the answering system.

11 – IN USE light

• Flashes when there is an incoming call, or

another telephone sharing the same line is in use.

• On when the telephone is in use, or the

answering system is answering a call.

Handset overview

1 – Handset earpiece

2 – LCD display

3 – CID/VOL-

• Review the caller ID log when the telephone is not

in use.

• Scroll down while in a menu, or in the directory,

caller ID log or redial list.

• Move the cursor to the left when entering numbers

or names.

• Decrease the listening volume during a call or

message playback.

4 – /FLASH

• Make or answer a call.

• Answer an incoming call when you receive a call

waiting alert.

5 – 1

• Press repeatedly to add or remove 1 in front of the

caller ID log entry before dialing or saving it to the

directory.

6 – TONE

• Switch to tone dialing temporarily during a call.

7 – MUTE/DELETE

• Mute the microphone during a call.

• Silence the handset ringer temporarily while the

phone is ringing.

• Delete the displayed entry while reviewing the

directory, caller ID log or redial list.

• Delete digits or characters when entering numbers

or names.

8 – Microphone

9 – Charging pole

10 – MENU/SELECT

• Show the menu.

• While in a menu, press to select an item, or save

an entry or setting.

11 – /VOL+

• Review the directory when the phone is not in

use.

• Scroll up while in a menu, or in the directory,

caller ID log or redial list.

• Move the cursor to the right when entering

numbers or names.

• Increase the listening volume during a call or

message playback.

12 – OFF/CANCEL

• Hang up a call.

• Return to the previous menu or idle mode without

making changes.

• Delete digits while predialing.

• Silence the handset ringer temporarily while the

phone is ringing.

• Erase the missed call indicator while the handset

is not in use.

13 – 0/OPER

• Enter space character during text editing.

14 – #

• Show other dialing options when reviewing a

caller ID log entry.

15 – REDIAL/PAUSE

• Review the redial list.

• Insert a dialing pause while dialing or entering

numbers into the directory.

16 – Battery compartment cover

Charger overview

1 – Charging pole

Display icons overview

The battery icon flashes when the

battery is low and needs charging.

The battery icon animates when the

battery is charging.

The battery icon becomes solid when

the battery is fully charged.

There are new messages on the

built-in answering system.

There are new voicemail received

from your telephone service provider.

NEW There are new caller ID log entries.

ANS ON The answering system is turned on.

1 The message number currently

playing.

Connect

You can choose to connect the telephone base

for desktop usage or wall mounting.

NOTES

• Use only the adapters provided.

• Make sure the electrical outlets are not controlled by

wall switches.

• The adapters are intended to be correctly oriented in

a vertical or floor mount position. The prongs are not

designed to hold the plug in place if it is plugged into

a ceiling, under-the-table or cabinet outlet.

TIP

• If you subscribe to digital subscriber line (DSL)

high-speed Internet service through your telephone

line, make sure you install a DSL lter (not included)

between the telephone line cord and telephone wall

jack. Contact your DSL service provider for more

information.

Connect the telephone base

Connect the charger

Mount the telephone base

Install and charge the battery

Install the battery

Install the battery as shown below.

NOTES

• Use only supplied battery.

• Charge the battery provided with this product only

in accordance with the instructions and limitations

specified in this manual.

• If the handset will not be used for a long time,

disconnect and remove the battery to prevent

possible leakage.

Charge the battery

Place the handset in the telephone base or the

charger to charge.

Once you have installed the battery, the handset

LCD display indicates the battery status (see the

table below).

NOTES

• For best performance, keep the handset in the

telephone base or charger when not in use.

• The battery is fully charged after 16 hours of

continuous charging.

• If you place the handset in the telephone base or

the charger without plugging in the battery, the

screen displays No battery.

Battery

indicators Battery status Action

The screen

is blank, or

displays Put in

charger and

flashes.

The battery has

no or very little

charge. The

handset cannot

be used.

Charge without

interruption

(at least 30

minutes).

The screen

displays

Low battery

and flashes.

The battery has

enough charge

to be used for a

short time.

Charge without

interruption

(about 30

minutes).

The screen

displays

HANDSET X.

The battery is

charged.

To keep the

battery charged,

place it in the

telephone base

or charger when

not in use.

Before use

After you install your telephone or power returns

following a power outage, the handset will prompt

you to set the date and time.

Set date and time

NOTE

• Make sure you set the date and time including the

year correctly; otherwise the answering system does

not announce the correct day of the week for your

recorded messages time stamp.

1. Use the dialing keys (0-9) to enter the month

(MM), date (DD) and year (YY). Then press

SELECT.

2. Use the dialing keys (0-9) to enter the hour

(HH) and minute (MM). Then press

q or p

choose AM or PM.

3. Press SELECT to save.

Check for dial tone

Press . If you hear a dial tone, the installation is

successful.

If you do not hear a dial tone:

• Make sure the installation procedures

described above are properly done.

• It may be a wiring problem. If you have

changed your telephone service to digital

service from a cable company or a VoIP

service provider, the telephone line may need

to be rewired to allow all existing telephone

jacks to work. Contact your cable/VoIP service

provider for more information.

Operating range

This cordless telephone operates with the

maximum power allowed by the Federal

Communications Commission (FCC). Even

so, this handset and telephone base can

communicate over only a certain distance - which

can vary with the locations of the telephone base

and handset, the weather, and the layout of your

home or office.

When the handset is out of range, the handset

displays Out of range or no pwr at base.

If there is a call while the handset is out of range,

it may not ring, or if it does ring, the call may not

connect well when you press . Move closer to

the telephone base, then press to answer the

call.

If the handset moves out of range during

a telephone conversation, there may be

interference. To improve reception, move closer

to the telephone base.

Use the handset menu

1. Press MENU when the phone is not in use.

2. Press or until the screen displays the

desired feature menu.

3. Press SELECT.

• To return to the previous menu, press

CANCEL.

• To return to idle mode, press and hold

CANCEL.

Congure your telephone

Set language

The LCD language is preset to English. You can

select English, French or Spanish to be used in

all screen displays.

1. Press MENU when the handset is not in use.

2. Scroll to Settings, then press SELECT twice.

3. Scroll to choose English, Français or

Español.

4. Press SELECT twice to save your setting.

Set date and time

NOTE

• Make sure you set the date and time including the

year correctly; otherwise the answering system does

not announce the correct day of the week for your

recorded messages time stamp.

1. Press MENU on the handset when not in use.

2. Scroll to Set date/time and then press

SELECT.

3. Use the dialing keys (0-9) to enter the month

(MM), date (DD) and year (YY). Then press

SELECT.

4. Use the dialing keys (0-9) to enter the hour

(HH) and minute (MM). Then press

q or p

choose AM or PM.

5. Press SELECT.

Temporary tone dialing

If you have pulse (rotary) service only, you

can switch from pulse to touch-tone dialing

temporarily during a call.

1. During a call, press TONE .

2. Use the dialing keys to enter the relevant

number. The telephone sends touch-tone

signals. It automatically returns to pulse dialing

mode after you end the call.

Telephone operations Make a call

• Press , and then dial the telephone number.

Answer a call

• Press or any of the dialing keys.

End a call:

• Press OFF or put the handset back in the

telephone base or charger.

Volume

• During a call, press VOL- or VOL+ to adjust

the listening volume.

Mute

The mute function allows you to hear the other party

but the other party cannot hear you.

1. During a call, press MUTE. The handset

displays Muted.

2. Press MUTE again to resume the

conversation. The handset displays

Microphone on briefly.

Join a call in progress (for multiple handset

models only)

You can use three handsets at a time on an

outside call.

• When a handset is already on a call, press

on another handset to join the call.

• To exit the call, press OFF on the handset or

place it in the telephone base or charger. The

call continues until all handsets hang up.

Call waiting

When you subscribe to call waiting service from

your telephone service provider, you hear an alert

tone if there is an incoming call while you are

already on a call.

• Press FLASH to put the current call on hold

and take the new call.

• Press FLASH at any time to switch back and

forth between calls.

Find handset

Use this feature to find the system handset.

To start paging:

• Press /FIND HANDSET on the telephone

base when not in use. All idle handsets ring

and display ** Paging **.

To end paging:

• Press /FIND HANDSET at the telephone

base.

-OR-

• Press or any of the dialing keys on the

handset.

NOTE

• Do not press and hold /FIND HANDSET for

more than four seconds. It may lead to handset

deregistration.

Redial list

Each handset stores the last five telephone

numbers dialed. When there are already five

entries, the oldest entry is deleted to make room

for the new entry.

Review and dial a redial list entry

1. Press REDIAL when the handset is not in use.

2. Press q, p or REDIAL repeatedly until the

desired entry displays.

3. Press to dial.

Delete a redial list entry

• When the desired redial entry displays, press

DELETE.

Directory

The directory can store up to 30 entries, which are

shared by all handsets. Each entry may consist of

a telephone number up to 30 digits, and a name

up to 15 characters.

Add a directory entry

1. Enter the number when the phone is not in

use. Press MENU, then go to Step 3.

-OR-

Press MENU when the phone is not in use,

then press or to scroll to Directory. Press

SELECT twice to choose Add contact.

2. Use the dialing keys to enter the number.

-OR-

Copy a number from the redial list by pressing

REDIAL and then press q, p or REDIAL

repeatedly to select a number. Press SELECT

to copy the number.

3. Press SELECT to move on to enter the name.

4. Use the dialing keys to enter the name.

Additional key presses show other characters

of that particular key.

5. Press SELECT to save.

While entering names and numbers, you can:

• Press DELETE to backspace and erase a digit

or character.

• Press and hold DELETE to erase the entire

entry.

• Press q or p to move the cursor to the left or

right.

• Press and hold PAUSE to insert a dialing

pause (for entering numbers only).

• Press 0 to add a space (for entering names

only).

Review a directory entry

Entries are sorted alphabetically.

1. Press when the phone is not in use.

2. Scroll to browse through the directory, or use the

dialing keys to start a name search.

Delete a directory entry

1. When the desired entry displays, press

DELETE.

2. When the handset displays Delete contact?,

press SELECT.

Edit a directory entry

1. When the desired entry displays, press

SELECT.

2. Use the dialing keys to edit the number, then

press SELECT.

3. Use the dialing keys to edit the name, then

press SELECT.

Dial a directory entry

• When the desired entry appears, press to

dial.

Caller ID

If you subscribe to caller ID service, information

about each caller appears after the first or

second ring. If you answer a call before the caller

information appears on the screen, it will not be

saved in the caller ID log.

The caller ID log stores up to 30 entries. Each

entry has up to 24 digits for the phone number

and 15 characters for the name.

If the telephone number has more that 15

digits, only the last 15 digits appear. If the name

has more than 15 characters, only the first 15

characters are shown and saved in the caller ID

log.

Review a caller ID log entry

1. Press CID when the phone is not in use.

2. Scroll to browse through the caller ID log.

Missed call indicator

When there are calls that have not been reviewed

in the caller ID log, the handset displays

XX missed calls.

Each time you review a caller ID log entry marked

NEW, the number of missed calls decreases by

one.

When you have reviewed all the missed calls, the

missed call indicator no longer displays.

If you do not want to review the missed calls

one by one, press and hold CANCEL on the idle

handset to erase the missed call indicator. All the

entries are then considered old.

Dial a caller ID log entry

• When the desired entry appears, press to

dial.

Save a caller ID log entry to the directory

1. When the desired caller ID log entry displays,

press SELECT.

2. Use the dialing keys to modify the number, if

necessary. Then press SELECT.

3. Use the dialing keys to modify the name, if

necessary. Then press SELECT.

Delete the caller ID log entries

• When the desired caller ID log entry displays,

press DELETE.

To delete all caller ID log entries:

1. Press MENU when the phone is not in use.

2. Scroll to Caller ID log and then press SELECT.

3. Scroll to Del all calls then press SELECT

twice.

Sound settings

Key tone

You can turn the key tone on or off.

1. Press MENU when the handset is not in use.

2. Scroll to Settings and then press SELECT.

3. Scroll to choose Key tone, then press

SELECT.

4. Press q or p to choose On or Off, then press

SELECT to save.

Ringer tone

You can choose from different ringer tones for

each handset.

1. Press MENU when the handset is not in use.

2. Scroll to Ringers and then press SELECT.

3. Scroll to choose Ringer tone, then press

SELECT.

4. Press q or p to sample each ringer tone, then

press SELECT to save.

NOTE

• If you turn off the ringer volume, you will not hear

ringer tone samples.

Telephone base ringer volume

Press p/VOLUME or q/VOLUME on the

telephone base to adjust the ringer volume when

the telephone base is not in use.

When you set the ringer volume to zero, the base

ringer is off. The telephone base announces,

“Base ringer is off.”

Handset ringer volume

You can adjust the handset ringer volume level, or

turn the ringer off.

1. Press MENU when the handset is not in use.

2. Scroll to Ringers and then press SELECT

twice.

3. Press q or p to sample each volume level,

then press SELECT to save.

NOTE

• When the ringer volume is set to Off, the handset

still rings when you press /FIND HANDSET at the

telephone base.

Temporary ringer silencing

When the telephone is ringing, you can

temporarily silence the ringer without

disconnecting the call. The next call rings

normally at the preset volume.

To silence the handset ringer:

• Press CANCEL or MUTE. The handset

displays Ringer muted.

To silence the telephone base ringer:

• Press /VOLUME.

About the built-in answering

system and voicemail service

For message recording, your telephone has a

built-in answering system, and it also supports

voicemail service offered by your telephone

service provider (subscription is required, and fee

may apply).

The main differences between them are:

Category Built-in

answering system

Voicemail from

telephone

service

Storage Messages are

stored in the

telephone base.

Messages are

stored in a

server or system

provided by

your telephone

service provider.

Your messages

will not be deleted

automatically.

You have to delete

your messages

manually.

Your messages

may be

automatically

deleted after a

period of time.

Contact your

telephone

service provider

for more details.

Method

to retrieve

messages

When you

received new

messages,

the handset

displays XX new

messages and

, and the

message window

on the telephone

base flashes.

When you

received new

messages, the

handset displays

and New

voicemail.

To retrieve

messages, usually

there are two

ways:

• Press on

the telephone

base; or

• Access

remotely with

an access

code.

To retrieve

messages, you

need an access

number and/

or a passcode

provided by

your telephone

service provider.

Abridged user’s manual

Telephones identified with this

logo have reduced noise and

interference when used with most

T-coil equipped hearing aids and

cochlear implants. The TIA-1083

Compliant Logo is a trademark of

the Telecommunications Industry

Association. Used under license.

Compatible with

Hearing Aid T-Coil

TIA-1083

Congratulations

on purchasing your new VTech product. Before

using this telephone, please read Important

safety instructions.

This abridged user’s manual provides you with

basic installation and use instructions. A limited

set of features are described in abbreviated form.

Please refer to the online user’s manual for a full

set of installation and operation instructions at

www.vtechcanada.com.

CS6120-2

CS6120-31

CS6124

CS6124-2

CS6124-31

DECT 6.0 cordless telephone

Go to www.vtechphones.com

to register your product for

enhanced warranty support and

the latest VTech product news.

1 set for

CS6124;

2 sets for

CS6120-2/

CS6124-2;

3 sets for

CS6120-31/

CS6124-31

1 set for CS6120-2/CS6124-2;

2 sets for CS6120-31/CS6124-31

THIS SIDE UP

Abridged

user’s

manual

Handset control key panel:

CANCEL

Important

safety

instructions

Set your built-in answering system

The answering system can record and store

up to 99 messages. Each message can be up

to three minutes in length. The total storage

capacity for the announcement, messages and

memos is approximately 11 minutes. The actual

recording time depends on individual message

characteristics.

Your answering system allows you to set your

announcement, to save and delete messages,

activate call screening, to set number of rings

before pick up, to access remotely, and to control

the recording time.

Turn the answering system on or off

The answering system must be turned on to

answer and record messages.

To turn on or off with the telephone base:

• Press /ANS ON/OFF to turn the built-in

answering system on or off.

To turn on or off with the handset:

1. Press MENU when the phone is not in use.

2. Scroll to Answering sys and then press

SELECT.

3. Scroll to Answer on/off and then press

SELECT.

4. Press q or p to choose On or Off and then

press SELECT.

Set voice language

The voice prompt language is preset to English.

You can select English or French to be used for

the voice prompts in your answering system.

1. Press MENU when the handset is not in use.

2. Scroll to Answering sys and then press

SELECT.

3. Scroll to Ans sys setup and then press

SELECT.

4. Scroll to Voice language and then press

SELECT.

5. Scroll to choose English or Français.

6. Press SELECT to save your setting.

Default announcement

The telephone is preset with a greeting that

answers calls with “Hello, please leave a

message after the tone.” You can use this preset

announcement, or replace it with your own.

Record your own announcement

The announcement can be up to 90 seconds in

length.

1. Press MENU when the phone is not in use.

2. Scroll to Answering sys then press SELECT

twice.

3. The handset announces, “To play, press 2. To

record, press 7.” Then press 7 to record.

4. The handset announces, “Record after the

tone. Press 5 when you are done.” After the

tone, speak towards the handset microphone.

5. Press 5 when done.

Play the announcement

1. Press MENU when the phone is not in use.

2. Scroll to Answering sys then press SELECT

twice.

3. The handset announces, “To play, press 2.

To record, press 7.” Then press 2 to play the

current announcement.

Options during playback:

• Press VOL+ or VOL- to adjust the listening

volume.

• Press 5 or OFF to stop at any time.

Delete the announcement

1. Press MENU when the phone is not in use.

2. Scroll to Answering sys then press SELECT

twice.

3. The handset announces, “To play, press 2. To

record, press 7.” Then press 3 to delete your

own recorded announcement.

NOTE

• After you deleted your own recorded announcement,

the answering system answers calls with the default

announcement.

Set number of rings

You can set the answering system to answer

an incoming call after two, three, four, five or six

rings; or toll saver. If you choose toll saver, the

answering system answers a call after two rings

when you have new messages, or after four rings

when you have no new messages.

1. Press MENU when the phone is not in use.

2. Scroll to Answering sys and then press

SELECT.

3. Scroll to Ans sys setup and then press

SELECT.

4. Scroll to # of rings and then press SELECT.

5. Press q or p to choose 6, 5, 4, 3, 2 or Toll

saver and then press SELECT.

Set recording time

You can set the recording time for each incoming

message.

1. Press MENU when the phone is not in use.

2. Scroll to Answering sys and then press

SELECT.

3. Scroll to Ans sys setup and then press

SELECT.

4. Scroll to Recording time and then press

SELECT.

5. Press q or p to choose 3 minutes,

2 minutes or 1 minute, and then press

SELECT.

Use your built-in answering system

New message indication

When there are new answering system

messages, the handset displays XX new

messages and , and the message window

on the telephone base flashes. When you are

reviewing a new message, NEW and display

on the handset.

If the message alert tone is turned on, the

telephone base beeps every 10 seconds when

there are messages that have not been reviewed.

Message playback

To playback messages at the telephone base:

• Press when the phone is not in use.

Options during playback:

• Press /VOLUME or /VOLUME to adjust the

listening volume.

• Press /SKIP to skip to the next message.

• Press /REPEAT to repeat the playing

message. Press /REPEAT twice to listen to

the previous message.

• Press X/DELETE to delete the playing message.

The system advances to the next message.

• Press /STOP to stop.

To playback messages with a handset:

• Press MENU when the phone is not in use,

and then press SELECT.

Options during playback:

• Press VOL- or VOL+ to adjust the listening

volume.

• Press 6 to skip to the next message.

• Press 4 to repeat the playing message. Press

4 twice to listen to the previous message.

• Press 3 to delete the playing message. The

system advances to the next message.

• Press OFF to stop the playback.

Delete all messages

You can only delete old (reviewed) messages.

You cannot delete new messages until you review

them. You cannot retrieve deleted messages.

To delete all messages with the telephone

base:

• Press X/DELETE twice when the phone is not

in use.

To delete all messages with a handset:

1. Press MENU when the phone is not in use.

2. Scroll to Answering sys and then press SELECT.

3. Scroll to Delete all old and then press

SELECT twice.

Remote access

A two-digit security code is required to access the

answering system remotely from any touch-tone

telephone. The preset code is 19. You can use

this preset code, or set your own.

1. Dial your telephone number from any touch-

tone telephone.

2. When the system plays your announcement,

enter the two-digit security code.

3. Enter one of the following remote commands.

Command Description

1Play all messages.

2Play only new messages.

3Delete the current message (during

playback).

33 Delete all old messages.

4Repeat the current message (during

playback).

5Stop.

*5 Hear a list of remote commands.

6Skip to the next message (during

playback).

*7 Record a new announcement.

8End the call.

0Turn the answering system on or off.

4. Hang up or press 8 to end the call.

Remote access code

You can set your own remote access code from

00 to 99.

1. Press MENU when the phone is not in use.

2. Scroll to Answering sys and then press

SELECT.

3. Scroll to Ans sys setup and then press

SELECT.

4. Scroll to Remote code and then press

SELECT.

5. Press the dialing keys (0-9) to enter the code,

or q or p to select from 00 to 99, then press

SELECT.

Use the built-in answering system

and voicemail service

You can use your answering system and

voicemail service together by setting your

answering system to answer before voicemail

service answers as described below. To learn

how to program your voicemail settings, contact

your telephone service provider.

If you are on a call, or if the answering system

is busy recording a message and you receive

another call, the second caller can leave a

voicemail message.

Set your answering system to answer calls

at least two rings earlier than your voicemail

service is set to answer. For example, if your

voicemail service answers after six rings, set

your answering system to answer after four rings.

Some voicemail service providers may program

the delay before answering calls in seconds

instead of rings. In this case, allow six seconds

per ring when determining the appropriate setting.

Retrieve voicemail from telephone

service

Voicemail is a feature available from most

telephone service providers. It may be included

with your telephone service, or may be optional.

Fees may apply.

Retrieve voicemail

When you received a voicemail, the handset

displays and New voicemail. To retrieve,

you typically dial an access number provided by

your telephone service provider, and then enter

a security code. Contact your telephone service

provider for instructions on how to configure the

voicemail settings and listen to messages.

NOTE

• After you have listened to all new voicemail

messages, the indicators on the handset turn off

automatically.

Turn off the new voicemail indicators

If you have retrieved your voicemail while away

from home, and the handset still displays the new

voicemail indicators, use this feature to turn off

the indicators.

NOTE

• This feature turns off the indicators only, it does not

delete your voicemail messages.

1. Press MENU when the phone is not in use.

2. Scroll to Settings and then press SELECT.

3. Scroll to Clr voicemail and then press

SELECT.

4. Press SELECT again to confirm.

When your handset is deregistered from the

telephone base, follow the steps below to register

it back to the telephone base.

1. Remove the handset from the telephone base.

2. Press and hold /FIND HANDSET at the

telephone base for about four seconds until

the IN USE light turns on.

3. Then press # on the handset. It displays

Registering...

The handset show Registered and you hear a

beep when the registration process completes.

The registration process takes about 60 seconds

to complete.

General product care

Taking care of your telephone

Your cordless telephone contains sophisticated

electronic parts, so it must be treated with care.

Avoid rough treatment

Place the handset down gently. Save the original

packing materials to protect your telephone if you

ever need to ship it.

Avoid water

Your telephone can be damaged if it gets wet.

Do not use the handset outdoors in the rain,

or handle it with wet hands. Do not install the

telephone base near a sink, bathtub or shower.

Electrical storms

Electrical storms can sometimes cause power

surges harmful to electronic equipment. For your

own safety, take caution when using electrical

appliances during storms.

Cleaning your telephone

Your telephone has a durable plastic casing that

should retain its luster for many years. Clean it

only with a dry non-abrasive cloth. Do not use

dampened cloth or cleaning solvents of any kind.

Frequently asked questions

Below are the questions most frequently asked

about the cordless telephone. If you cannot find

the answer to your question, visit our website at

www.vtechcanada.com or call 1 (800) 267-7377

for customer service.

My telephone

does not work

at all.

Make sure the telephone

base is installed properly,

and battery is installed

and charged correctly. For

optimum daily performance,

return the handset to the

telephone base after use.

The display

shows No line.

I cannot hear the

dial tone.

Disconnect the telephone

line cord from your

telephone and connect it to

another telephone. If there

is no dial tone on that other

telephone either, then the

telephone line cord may be

defective. Try installing a

new telephone line cord.

If changing the telephone

line cord does not help,

the wall jack (or the wiring

to this wall jack) may be

defective. Contact your

telephone service provider.

You may be using a new

cable or VoIP service, the

existing telephone jacks in

your home may no longer

work. Contact your service

provider for solutions.

The answering

system does

not record

messages.

Make sure the answering

system is on. When the

answering system is on,

ANS ON should display

on the handset and the

telephone base.

When the answering

machine memory is full,

it does not record new

messages until some old

messages are deleted.

If you subscribe to

voicemail service, change

the number of rings so

that your answering

system answers before

your voicemail service

answers. To determine how

many rings activate your

voicemail service, contact

your telephone service

provider.

The answering

system does

not announce

the correct day

of the week

for recorded

messages time

stamp.

Make sure you have set

the date and time. See

Congure your telephone

section.

The messages

on the answering

system are

incomplete.

If a caller leaves a very long

message, part of it may be

lost when the answering

system disconnects the call

after the preset recording

time.

If the memory on the

answering system becomes

full during a message, the

answering system stops

recording and disconnects

the call.

I accidentally

set my LCD

language to

Spanish or

French, and I

don’t know how

to change it back

to English.

While the handset is not

in use, press MENU and

then enter 364# to change

the handset LCD language

back to English.

Important safety instructions

When using your telephone equipment, basic safety

precautions should always be followed to reduce the risk of

fire, electric shock and injury, including the following:

1. Read and understand all instructions.

2. Follow all warnings and instructions marked on the

product.

3. Unplug this product from the wall outlet before cleaning.

Do not use liquid or aerosol cleaners. Use a damp cloth

for cleaning.

4. Do not use this product near water such as near a bath

tub, wash bowl, kitchen sink, laundry tub or a swimming

pool, or in a wet basement or shower.

5. Do not place this product on an unstable table, shelf,

stand or other unstable surfaces.

6. Avoid placing the telephone system in places with

extreme temperature, direct sunlight, or other electrical

devices. Protect your phone from moisture, dust,

corrosive liquids and fumes.

7. Slots and openings in the back or bottom of the telephone

base and handset are provided for ventilation. To protect

them from overheating, these openings must not be

blocked by placing the product on a soft surface such as

a bed, sofa or rug. This product should never be placed

near or over a radiator or heat register. This product

should not be placed in any area where proper ventilation

is not provided.

8. This product should be operated only from the type of

power source indicated on the marking label. If you are

not sure of the type of power supply in your home or

office, consult your dealer or local power company.

9. Do not allow anything to rest on the power cord. Do not

install this product where the cord may be walked on.

10. Never push objects of any kind into this product through

the slots in the telephone base or handset because they

may touch dangerous voltage points or create a short

circuit. Never spill liquid of any kind on the product.

11. To reduce the risk of electric shock, do not disassemble

this product, but take it to an authorized service facility.

Opening or removing parts of the telephone base or

handset other than specified access doors may expose

you to dangerous voltages or other risks. Incorrect

reassembling can cause electric shock when the product

is subsequently used.

12. Do not overload wall outlets and extension cords.

13. Unplug this product from the wall outlet and refer

servicing to an authorized service facility under the

following conditions:

• When the power supply cord or plug is damaged or

frayed.

• If liquid has been spilled onto the product.

• If the product has been exposed to rain or water.

• If the product does not operate normally by following

the operating instructions. Adjust only those controls

that are covered by the operation instructions.

Improper adjustment of other controls may result

in damage and often requires extensive work by

an authorized technician to restore the product to

normal operation.

• If the product has been dropped and the telephone

base and/or handset has been damaged.

• If the product exhibits a distinct change in

performance.

14. Avoid using a telephone (other than cordless) during an

electrical storm. There is a remote risk of electric shock

from lightning.

15. Do not use the telephone to report a gas leak in the

vicinity of the leak. Under certain circumstances, a

spark may be created when the adapter is plugged

into the power outlet, or when the handset is replaced

in its cradle. This is a common event associated with

the closing of any electrical circuit. The user should

not plug the phone into a power outlet, and should not

put a charged handset into the cradle, if the phone is

located in an environment containing concentrations of

flammable or flame-supporting gases, unless there is

adequate ventilation. A spark in such an environment

could create a fire or explosion. Such environments

might include: medical use of oxygen without adequate

ventilation; industrial gases (cleaning solvents; gasoline

vapors; etc.); a leak of natural gas; etc.

16. Only put the handset of your telephone next to your ear

when it is in normal talk mode.

17. The power adapter is intended to be correctly oriented

in a vertical or floor mount position. The prongs are not

designed to hold the plug in place if it is plugged into a

ceiling, under-the-table or cabinet outlet.

SAVE THESE INSTRUCTIONS

Battery

• Use only the battery provided or equivalent.

To order a replacement, visit our website at

www.vtechcanada.com or call

1 (800) 267-7377.

• Do not dispose of the battery in a fire. Check with

local waste management codes for special disposal

instructions.

• Do not open or mutilate the battery. Released electrolyte

is corrosive and may cause burns or injury to the eyes or

skin. The electrolyte may be toxic if swallowed.

• Exercise care in handling batteries in order not to create

a short circuit with conductive materials.

• Charge the battery provided with or identified for use

with this product only in accordance with the instructions

and limitations specified in this manual.

Precautions for users of implanted cardiac pacemakers

Cardiac pacemakers (applies only to digital cordless

telephones):

Wireless Technology Research, LLC (WTR), an

independent research entity, led a multidisciplinary

evaluation of the interference between portable wireless

telephones and implanted cardiac pacemakers. Supported

by the U.S. Food and Drug Administration, WTR

recommends to physicians that:

Pacemaker patients

• Should keep wireless telephones at least six inches

from the pacemaker.

• Should NOT place wireless telephones directly over the

pacemaker, such as in a breast pocket, when it is turned

ON.

• Should use the wireless telephone at the ear opposite

the pacemaker.

WTR’s evaluation did not identify any risk to bystanders with

pacemakers from other persons using wireless telephones.

About cordless telephones

• Privacy: The same features that make a cordless

telephone convenient create some limitations.

Telephone calls are transmitted between the telephone

base and the cordless handset by radio waves, so there

is a possibility that the cordless telephone conversations

could be intercepted by radio receiving equipment within

range of the cordless handset. For this reason, you

should not think of cordless telephone conversations as

being as private as those on corded telephones.

• Electrical power: The telephone base of this cordless

telephone must be connected to a working electrical

outlet. The electrical outlet should not be controlled by

a wall switch. Calls cannot be made from the cordless

handset if the telephone base is unplugged, switched off

or if the electrical power is interrupted.

• Potential TV interference: Some cordless telephones

operate at frequencies that may cause interference

to televisions and VCRs. To minimize or prevent such

interference, do not place the telephone base of the

cordless telephone near or on top of a TV or VCR.

If interference is experienced, moving the cordless

telephone farther away from the TV or VCR often

reduces or eliminates the interference.

• Rechargeable batteries: Exercise care in handling

batteries in order not to create a short circuit with

conducting material such as rings, bracelets and keys.

The battery or conductor may overheat and cause harm.

Observe proper polarity between the battery and the

battery charger.

• Nickel-metal hydride rechargeable batteries:

Dispose of these batteries in a safe manner. Do not

burn or puncture the battery. Like other batteries of this

type, if burned or punctured, they could release caustic

material which could cause injury.

For C-UL compliance only

Mesures de sécurité importantes

Aﬁn de réduire les risques d’incendie, de blessures corporelles

ou d’électrocution, suivez toujours ces mesures préventives de

base lorsque vous utilisez votre téléphone :

1. Lisez et comprenez bien toutes les instructions.

2. Observez toutes les instructions et mises en garde inscrites

sur l’appareil.

3. Débranchez ce téléphone de la prise murale avant de le

nettoyer. N’utilisez pas de nettoyeurs liquides ni en aérosol.

N’utilisez qu’un chiffon doux et légèrement humecté.

4. N’utilisez pas ce produit près de l’eau, tel que près d’un bain,

d’un lavabo, d’un évier de cuisine, d’un bac de lavage ou

d’une piscine, ou dans un sous-sol humide ou sous la douche.

5. Ne déposez pas ce téléphone sur un chariot, support

ou table chancelants. L’appareil pourrait tomber et être

sérieusement endommagé.

6. Évitez d’installer le système téléphonique dans les endroits

soumis à une température extrême, à la lumière directe du

soleil ou à proximité immédiate d’autres appareils électriques

ou électroniques. Protégez votre téléphone contre les

sources d’humidité, la poussière, les vapeurs et les liquides

corrosifs.

7. Le boîtier de l’appareil est doté de fentes et d’ouvertures

d’aération situées à l’arrière ou en dessous. Aﬁn d’empêcher

la surchauffe, ces ouvertures ne doivent pas être obstruées

en plaçant l’appareil sur un lit, divan, tapis ou autre surface

similaires. Ne placez pas cet appareil à proximité d’un

élément de chauffage ni d’une plinthe électrique. De plus,

ne l’installez pas dans une unité murale ou un cabinet fermé

qui ne possède pas d’aération adéquate.

8. Ne faites fonctionner cet appareil qu’avec le type

d’alimentation indiqué sur les étiquettes de l’appareil. Si vous

ne connaissez pas le voltage de votre maison, consultez votre

marchand ou votre fournisseur d’électricité.

9. Ne déposez rien sur le cordon d’alimentation. Installez cet

appareil dans un endroit sécuritaire, là où personne ne

pourra trébucher sur la ligne d’alimentation ni le cordon

téléphonique modulaire.

10. N’insérez jamais d’objets à travers les fentes et ouvertures de

cet appareil, car ils pourraient toucher à des points de tension

dangereux ou court-circuiter des pièces, ce qui constituerait

un risque d’incendie ou d’électrocution. N’échappez pas de

liquides dans l’appareil.

11. Aﬁn de réduire les risques d’électrocution, ne démontez

pas l’appareil, mais apportez-le plutôt à un centre de service

qualiﬁé s’il doit être réparé. En enlevant le couvercle,

vous vous exposez à des tensions dangereuses ou autres

dangers similaires. Un remontage inadéquat peut être à

l’origine d’une électrocution lors d’une utilisation ultérieure

de l’appareil. Débranchez l’appareil avant de procéder au

nettoyage. Utilisez un chiffon humide et doux.

12. Ne surchargez pas les prises de courant et les rallonges.

13. Débranchez cet appareil de la prise de courant et

communiquez avec le département de service à la clientèle

de VTech dans les cas suivants :

• Lorsque le cordon d’alimentation est endommagé ou

écorché.

• Si du liquide a été échappé dans l’appareil.

• Si l’appareil a été exposé à une source d’humidité telle

que la pluie ou l’eau.

• Si le produit ne fonctionne pas normalement en

respectant les instructions de fonctionnement. Réglez

uniquement les commandes indiquées dans le les

instructions de fonctionnement. Les réglages incorrects

des autres commandes pourraient provoquer un

dommage qui pourrait exiger un travail exhaustif

de la part d’un technicien autorisé aﬁn de rétablir le

fonctionnement normal de l’appareil.

• Si le produit a été échappé et que le socle et/ou le

combiné a été endommagé.

• Si le produit afﬁche une nette diminution de sa

performance.

14. Évitez d’utiliser un téléphone (autre qu’un sans ﬁl) pendant

un orage. Les éclairs peuvent être à l’origine d’une

électrocution.

15. N’utilisez pas le téléphone pour rapporter une fuite de

gaz à proximité de la fuite. En certaines circonstances, une

ﬂammèche pourrait être provoquée lorsque l’adaptateur

est branché à une prise de courant, ou lorsque le combiné

est déposé sur le socle. Ceci est un événement commun

associé à la fermeture d’un circuit électrique. L’utilisateur ne

devrait pas brancher le téléphone à une prise de courant,

et ne devrait pas déposer le combiné chargé sur le socle, si

le téléphone se trouve à proximité d’un endroit comportant

des concentrations de gaz inﬂammables, à moins que

la ventilation soit adéquate. Une ﬂammèche dans un tel

endroit pourrait provoquer un incendie ou une explosion.

De tels environnements peuvent comprendre: des endroits

où l’on utilise de l’oxygène médical sans ventilation

adéquate; des gaz industriels (dissolvants de nettoyage, des

vapeurs d’essence, etc.); une fuite de gaz naturel, etc.

16. Ne placez que le combiné de votre téléphone près de votre

oreille lorsqu’en mode de conversation.

17. Ces adaptateurs ont été conçus pour être orientés en position

verticale ou montés au sol. Les broches ne sont pas conçues

pour maintenir l’adaptateur en place si celui-ci est barnché

dans une prise au plafond ou sous une table/ armoire.

18. Pour le MATERIEL RACCORDE PAR PRISE DE COURANT, le

socle de prise de courant doit etre installe a proximite du

materiel et doit etre aisement accessible.

CONSERVEZ CES INSTRUCTIONS

Pile

• N’utilisez que la pile incluse ou l’équivalent. Pour

commander une pile de recharge, visitez notre site Web au

www.vtechphones.com ou composez le 1-800-595-9511.

Au Canada, visitez le www.vtechcanada.com ou composez

le 1-800-267-7377.

• Ne jetez pas la pile au feu. Vériﬁez les instructions

spéciﬁques de mise aux rebus auprès des autorités locales.

• N’ouvrez pas et ne mutilez pas la pile. L’électrolyte qui s’en

échapperait est corrosif et pourrait causer des brûlures

ou des blessures aux yeux ou à la peau. L’électrolyte est

toxique si avalé.

• Soyez prudents lorsque vous manipulez les piles aﬁn

d’éviter les courts-circuits provoqués par des matériaux

conducteurs.

• Rechargez la pile incluse avec cet appareil, selon les

instructions et limites spéciﬁées dans ce guide d’utilisation.

Stimulateurs cardiaques implantés dans l’organisme

Les simulateurs cardiaques (s’applique uniquement aux

téléphones numériques sans ﬁl) :

L’organisme ‘Wireless Technology Research, LLC (WTR)’, une

ﬁrme de recherche indépendante, a mené une évaluation

pluridisciplinaire des interférences entre les téléphones sans

ﬁl portatifs et les stimulateurs cardiaques implantés dans

l’organisme. Appuyée par l’Administration des aliments et

drogues (FDA) des États-Unis, la ﬁrme WTR recommande aux

médecins :

Avis aux détenteurs de stimulateurs cardiaques

• Ils doivent tenir le téléphone sans ﬁl à une distance d’au

moins six pouces du stimulateur cardiaque.

• Ils ne doivent PAS placer le téléphone sans ﬁl directement

sur le stimulateur cardiaque, tel que dans une poche de

chemise, lorsque celui-ci est en marche.

• Ils doivent utiliser le téléphone sans ﬁl en l’appuyant

sur l’oreille qui se trouve dans la direction opposée au

stimulateur cardiaque.

L’étude effectuée par l’organisme WRS n’a pas identiﬁé de

risque pour les détenteurs de simulateurs cardiaques causés

par les gens qui utilisent un téléphone sans ﬁl à proximité de

ceux-ci.

À propos des téléphones sans ﬁl

Conﬁdentialité : Les mêmes caractéristiques qui constituent

des avantages pour les téléphones sans ﬁl afﬁchent également

des restrictions. Les appels téléphoniques sont transmis entre

le combiné sans ﬁl et le socle par le biais d’ondes radio ; il y a

donc la possibilité que vos conversations téléphoniques sans

ﬁl soient interceptées par des équipements de réception

radio se trouvant dans la portée du combiné sans ﬁl. Pour

cette raison, vous ne devez pas percevoir les communications

téléphoniques sans ﬁl comme étant aussi conﬁdentielles que

celles des téléphones à cordons.

Alimentation électrique : Le socle de ce téléphone sans ﬁl

doit être branché à une prise électrique fonctionnelle. La prise

électrique ne doit pas être contrôlée par un interrupteur mural.

Les appels ne pourront pas être effectués du combiné sans ﬁl

si le socle est débranché ou mis hors tension ou si le courant est

coupé.

Possibilité d’interférences aux téléviseurs : Certains téléphones

sans ﬁl fonctionnent sur des fréquences pouvant causer

des interférences aux téléviseurs et aux magnétoscopes.

Pour réduire ou prévenir de telles interférences, ne placez

pas le socle du téléphone sans ﬁl près ou sur un téléviseur

ou magnétoscope. S’il y a présence de parasites, il est

conseillé d’éloigner le téléphone sans ﬁl du téléviseur ou du

magnétoscope aﬁn de réduire possiblement les interférences.

Piles rechargeables : Manipulez les piles avec soin aﬁn de ne

pas les court-circuiter avec des bagues, bracelets ou clés. Les

piles ou le conducteur peut surchauffer et causer des blessures.

Respectez la polarité adéquate entre la pile et le chargeur.

Les bloc-piles rechargeables à l’hydrure métallique de nickel :

Jetez ces blocs-piles de manière écologique et sécuritaire. Ne

les incinérez pas et ne les percez pas. Tel que les autres piles

de ce type, elles pourraient dégager une matière toxique qui

peut causer des blessures corporelles si elles sont brûlées ou

percées.

The RBRC® seal

The RBRC® seal on the nickel-metal hydride battery

indicates that VTech Communications, Inc. is voluntarily

participating in an industry program to collect and recycle

these batteries at the end of their useful lives, when taken

out of service within the United States and Canada.

The RBRC® program provides a convenient alternative to

placing used nickel-metal hydride batteries into the trash or

municipal waste, which may be illegal in your area.

VTech’s participation in RBRC® makes it easy for you to

drop off the spent battery at local retailers participating in

the RBRC® program or at authorized VTech product service

centers. Please call 1 (800) 8 BATTERY® for information on

Ni-MH battery recycling and disposal bans/restrictions in

your area. VTech’s involvement in this program is part of its

commitment to protecting our environment and conserving

natural resources.

RBRC® and 1 (800) 8 BATTERY® are registered

trademarks of Rechargeable Battery Recycling

Corporation.

FCC, ACTA and IC regulations

FCC Part 15

This equipment has been tested and found to comply with the

requirements for a Class B digital device under Part 15 of the

Federal Communications Commission (FCC) rules. These

requirements are intended to provide reasonable protection

against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that

interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or

television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and

receiver.

• Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician

for help.

Changes or modifications to this equipment not expressly

approved by the party responsible for compliance could void

the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC rules. Operation

is subject to the following two conditions: (1) this device may

not cause harmful interference, and (2) this device must

accept any interference received, including interference that

may cause undesired operation. Privacy of communications

may not be ensured when using this telephone.

To ensure safety of users, the FCC has established criteria

for the amount of radio frequency energy that can be safely

absorbed by a user or bystander according to the intended

usage of the product. This product has been tested and found

to comply with the FCC criteria. The handset may be safely

held against the ear of the user. The telephone base shall be

installed and used such that parts of the user’s body other

than the hands are maintained at a distance of approximately

20 cm (8 inches) or more.

This Class B digital apparatus complies with Canadian

requirement:

CAN ICES-3 (B)/NMB-3(B).

FCC Part 68 and ACTA

This equipment complies with Part 68 of the FCC

rules and with technical requirements adopted by the

Administrative Council for Terminal Attachments (ACTA).

The label on the back or bottom of this equipment contains,

among other things, a product identifier in the format

US:AAAEQ##TXXXX. This identifier must be provided to

your telephone service provider upon request.

The plug and jack used to connect this equipment to

premises wiring and the telephone network must comply

with applicable Part 68 rules and technical requirements

adopted by ACTA. A compliant telephone cord and

modular plug is provided with this product. It is designed

to be connected to a compatible modular jack that is also

compliant. An RJ11 jack should normally be used for

connecting to a single line and an RJ14 jack for two lines.

See the installation instructions in the user’s manual.

The Ringer Equivalence Number (REN) is used to

determine how many devices you may connect to your

telephone line and still have them ring when you are called.

The REN for this product is encoded as the 6th and 7th

characters following the US: in the product identifier (e.g.,

if ## is 03, the REN is 0.3). In most, but not all areas, the

sum of all RENs should be five (5.0) or less. For more

information, please contact your telephone service provider.

This equipment may not be used with Party Lines. If you

have specially wired alarm dialing equipment connected

to your telephone line, ensure the connection of this

equipment does not disable your alarm equipment. If you

have questions about what will disable alarm equipment,

consult your telephone service provider or a qualified

installer.

If this equipment is malfunctioning, it must be unplugged

from the modular jack until the problem has been corrected.

Repairs to this telephone equipment can only be made

by the manufacturer or its authorized agents. For repair

procedures, follow the instructions outlined under the

Limited warranty.

If this equipment is causing harm to the telephone network,

the telephone service provider may temporarily discontinue

your telephone service. The telephone service provider

is required to notify you before interrupting service. If

advance notice is not practical, you will be notified as soon

as possible. You will be given the opportunity to correct

the problem and the telephone service provider is required

to inform you of your right to file a complaint with the FCC.

Your telephone service provider may make changes in its

facilities, equipment, operation, or procedures that could

affect the proper functioning of this product. The telephone

service provider is required to notify you if such changes

are planned.

If this product is equipped with a corded or cordless

handset, it is hearing aid compatible.

If this product has memory dialing locations, you may

choose to store emergency telephone numbers (e.g., police,

fire, medical) in these locations. If you do store or test

emergency numbers, please:

Remain on the line and briefly explain the reason for the call

before hanging up.

Perform such activities in off-peak hours, such as early

morning or late evening.

Industry Canada

This device contains licence-exempt transmitter(s)/

receiver(s) that comply with Innovation, Science and

Economic Development Canada’s licence-exempt RSS(s).

Operation is subject to the following two conditions: (1) this

device may not cause interference, and (2) this device must

accept any interference, including interference that may

cause undesired operation of the device.

The term ‘’IC:‘’ before the certification/registration

number only signifies that the Industry Canada technical

specifications were met.

The Ringer Equivalence Number (REN) for this terminal

equipment is 1.0. The REN is an indication of the maximum

number of devices allowed to be connected to a telephone

interface. The termination on an interface may consist of

any combination of devices subject only to the requirement

that the sum of the RENs of all the devices does not exceed

five.

This product meets the applicable Innovation, Science and

Economic Development Canada technical specifications.

Limited warranty

What does this limited warranty cover?

The manufacturer of this VTech Product warrants to the

holder of a valid proof of purchase (“Consumer” or “you”)

that the Product and all accessories provided in the sales

package (“Product”) are free from defects in material

and workmanship, pursuant to the following terms and

conditions, when installed and used normally and in

accordance with the Product operating instructions. This

limited warranty extends only to the Consumer for Products

purchased and used in the United States of America and

Canada.

What will VTech do if the Product is not free from

defects in materials and workmanship during the limited

warranty period (“Materially Defective Product”)?

During the limited warranty period, VTech’s authorized

service representative will repair or replace at VTech’s

option, without charge, a Materially Defective Product.

If we repair the Product, we may use new or refurbished

replacement parts. If we choose to replace the Product,

we may replace it with a new or refurbished Product of

the same or similar design. We will retain defective parts,

modules, or equipment. Repair or replacement of the

Product, at VTech’s option, is your exclusive remedy.

VTech will return the repaired or replacement Products to

you in working condition. You should expect the repair or

replacement to take approximately 30 days.

How long is the limited warranty period?

The limited warranty period for the Product extends for ONE

(1) YEAR from the date of purchase. If VTech repairs or

replaces a Materially Defective Product under the terms of

this limited warranty, this limited warranty also applies to the

repaired or replacement Product for a period of either (a) 90

days from the date the repaired or replacement Product is

shipped to you or (b) the time remaining on the original one-

year warranty; whichever is longer.

What is not covered by this limited warranty?

This limited warranty does not cover:

1. Product that has been subjected to misuse, accident,

shipping or other physical damage, improper installation,

abnormal operation or handling, neglect, inundation, fire,

water or other liquid intrusion;

2. Product that has been damaged due to repair, alteration or

modification by anyone other than an authorized service

representative of VTech;

3. Product to the extent that the problem experienced is

caused by signal conditions, network reliability, or cable or

antenna systems;

4. Product to the extent that the problem is caused by use

with non-VTech accessories;

5. Product whose warranty/quality stickers, product serial

number plates or electronic serial numbers have been

removed, altered or rendered illegible;

6. Product purchased, used, serviced, or shipped for repair

from outside the United States of America or Canada, or

used for commercial or institutional purposes (including but

not limited to Products used for rental purposes);

7. Product returned without a valid proof of purchase (see

item 2 below); or

8. Charges for installation or set up, adjustment of customer

controls, and installation or repair of systems outside the

unit.

How do you get warranty service?

To obtain warranty service, please visit our website at www.

vtechcanada.com or call 1 (800) 267-7377.

NOTE: Before calling for service, please review the user’s

manual - a check of the Product’s controls and features may

save you a service call.

Except as provided by applicable law, you assume the risk

of loss or damage during transit and transportation and are

responsible for delivery or handling charges incurred in the

transport of the Product(s) to the service location. VTech will

return repaired or replaced Product under this limited warranty.

Transportation, delivery or handling charges are prepaid.

VTech assumes no risk for damage or loss of the Product

in transit. If the Product failure is not covered by this limited

warranty, or proof of purchase does not meet the terms of this

limited warranty, VTech will notify you and will request that you

authorize the cost of repair prior to any further repair activity.

You must pay for the cost of repair and return shipping costs

for the repair of Products that are not covered by this limited

warranty.

What must you return with the Product to get warranty

service?

1. Return the entire original package and contents including

the Product to the VTech service location along with a

description of the malfunction or difficulty; and

2. Include a “valid proof of purchase” (sales receipt)

identifying the Product purchased (Product model) and the

date of purchase or receipt; and

3. Provide your name, complete and correct mailing address,

and telephone number.

Other limitations

This warranty is the complete and exclusive agreement

between you and VTech. It supersedes all other written or

oral communications related to this Product. VTech provides

no other warranties for this Product. The warranty exclusively

describes all of VTech’s responsibilities regarding the

Product. There are no other express warranties. No one is

authorized to make modifications to this limited warranty and

you should not rely on any such modification.

State/Provincial Law Rights: This warranty gives you specific

legal rights, and you may also have other rights, which vary

from state to state or province to province.

Limitations: Implied warranties, including those of fitness for a

particular purpose and merchantability (an unwritten warranty

that the Product is fit for ordinary use) are limited to one year

from the date of purchase. Some states/provinces do not

allow limitations on how long an implied warranty lasts, so the

above limitation may not apply to you. In no event shall VTech

be liable for any indirect, special, incidental, consequential,

or similar damages (including, but not limited to lost profits

or revenue, inability to use the Product or other associated

equipment, the cost of substitute equipment, and claims by

third parties) resulting from the use of this Product. Some

states/provinces do not allow the exclusion or limitation of

incidental or consequential damages, so the above limitation

or exclusion may not apply to you.

Please retain your original sales receipt

as proof of purchase.

Disclaimer and Limitation of Liability

VTech Communications, Inc. and its suppliers

assume no responsibility for any damage or loss

resulting from the use of this user’s manual. VTech

Communications, Inc. and its suppliers assume no

responsibility for any loss or claims by third parties

that may arise through the use of this product.

Company: VTech Communications, Inc.

Address: 9020 SW Washington Square Road -

Ste 555 Tigard, OR 97223, United States

Phone: 1 (800) 595-9511 in the U.S. or

1 (800) 267-7377 in Canada

Technical specications

Frequency

control

Crystal controlled PLL

synthesizer

Transmit

frequency

1921.536-1928.448 MHz

Channels 5

Nominal

effective

range

Maximum power allowed by

FCC and IC. Actual operating

range may vary according to

environmental conditions at the

time of use.

Power

requirements

Handset: 2.4V Ni-MH battery

Telephone base: 6V DC @ 400mA

Charger: 6V DC @ 400mA

Memory Directory:

30 memory locations;

up to 30 digits and 15 characters

Caller ID log:

30 memory locations;

up to 24 digits and 15 characters

Telephone base control key panel:

Specifications are subject to change without notice.

Document order number: 91-007061-070-100

VTech CS6120-2 Manuel utilisateur

Marque: VTech

Modèle: CS6120-2

Catégorie: Téléphones

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: VTech CS6120-2 User manual

VTech CS6120-2 Manuel utilisateur

VTech CS6120-2 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents