Simplicity INTEK AND QUANTUM 110000 Manuel utilisateur

Marque: Simplicity

Modèle: INTEK AND QUANTUM 110000

Taper: Manuel utilisateur

Document: - page 1 (Black)

Screen angle and frequency: 45.0000, 150.0000

Model Series

Covered in

This Manual

110000

120000

Operating & Maintenance

Instructions

Model Type Code

Month Day Year

Note: General Model Series numbers noted above are inclusive of the specific model

number found on your engine. To get replacement parts or technical assistance in

the future, write your engine Model, Type, Code and date of purchase here.

TABLE OF CONTENTS

Safety 3-5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Engine Information 6. . . . . . . . . . . . . . . . . . . . . . . .

Oil 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Fuel and Starting Information 8. . . . . . . . . . . . . . .

Starting and Stopping 9-10. . . . . . . . . . . . . . . . . . .

Maintenance 11-13. . . . . . . . . . . . . . . . . . . . . . . . .

Adjustments 14. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Parts and Service & Storage 15-16. . . . . . . . . . . .

Warranty Information 17. . . . . . . . . . . . . . . . . . . . .

WARNING

Briggs & Stratton does not approve or authorize the use of

these engines on 3-wheel All Terrain Vehicles (ATVs), motor

bikes, fun/recreational go-karts, aircraft products or vehicles

intended for use in competitive events. Use of these engines in

such applications could result in property damage, serious

injury (including paralysis), or even death.

Need assistance? Go to www.briggsandstratton.com

for detailed information regarding

Briggs & Stratton engines.

Or call,

1-800-233-3723, (U.S.A. and Canada)

to hear a menu of pre-recorded messages

offering engine maintenance information.

The Power That Works For You.

Look For Relevant Emissions Durability Period and Air Index Information On

Your Engine Emissions Label

Engines that are certified to meet the California Air Resources Board (CARB) Tier 2 Emission Standards must display information regard-

ing the Emissions Durability Period and the Air Index. Briggs & Stratton makes this information available to the consumer on our emission

labels. The engine emission label will indicate certification information.

The Emissions Durability Period describes the number of hours of actual running time for which the engine is certified to be emissions

compliant, assuming proper maintenance in accordance with the Operating & Maintenance Instructions. The following categories are

used:

Moderate: Engine is certified to be emission compliant for 125 hours of actual engine running time.

Intermediate: Engine is certified to be emission compliant for 250 hours of actual engine running time.

Extended: Engine is certified to be emission compliant for 500 hours of actual engine running time.

For example, a typical walk-behind lawn mower is used 20 to 25 hours per year. Therefore, the Emissions Durability Period of an

engine with an intermediate rating would equate to 10 to 12 years.

The Air Index is a calculated number describing the relative level of emissions for a specific engine family. The lower the Air Index,

the cleaner the engine. This information is displayed in graphical form on the emissions label.

After July 1, 2000, Look For Emissions Compliance Period On

Engine Emissions Compliance Label

After July 1, 2000 certain Briggs & Stratton engines will be certified to meet the United States Environmental Protection Agency (USEPA)

Phase 2 emission standards. For Phase 2 certified engines, the Emissions Compliance Period referred to on the Emissions Compliance

label indicates the number of operating hours for which the engine has been shown to meet Federal emission requirements. For engines

less than 225 cc displacement, Category C = 125 hours, B = 250 hours and A = 500 hours. For engines of 225 cc or more, Category

C = 250 hours, B = 500 hours and A = 1000 hours.

The displacement of model series 110000 engine is 167 cc, and model series 120000 engine is 190 cc.

This is a generic representation

of the emission label typically

found on a certified engine.

BEFORE OPERATING ENGINE

THE OPERATING & MAINTENANCE

INSTRUCTIONS CONTAIN SAFETY

INFORMATION TO:

• Make you aware of hazards associated with

engines

• Inform you of the risk of injury associated with

those hazards, and

• Tell you how to avoid or reduce the risk of injury.

275749

• Read entire Operating & Maintenance Instructions

AND the instructions for the equipment this engine

powers.*

• Failure to follow instructions could result in serious

injury or death.

* Briggs & Stratton does not necessarily know what equipment this en-

gine will power. For that reason, you should carefully read and under-

stand the operating instructions for the equipment on which your engine

is placed.

The safety alert symbol ( ) is used to identify safety

information about hazards that can result in personal injury.

A signal word (DANGER, WARNING, or CAUTION) is

used with the alert symbol to indicate the likelihood and the

potential severity of injury. In addition, a hazard symbol

may be used to represent the type of hazard.

DANGER indicates a hazard which, if not

avoided, will result in death or serious injury.

WARNING indicates a hazard which, if not

avoided, could result in death or serious injury.

CAUTION indicates a hazard which, if not

avoided, might result in minor or moderate

injury.

CAUTION, when used without the alert symbol,

indicates a situation that could result in damage

to the engine.

WARNING

The engine exhaust from this

product contains chemicals known

to the State of California to cause

cancer, birth defects, or other

reproductive harm.

HAZARD SYMBOLS AND MEANINGS

Explosion

Toxic Fumes

Moving Parts

Shock

Hot Surface

Kickback

Fire

THE INTERNATIONAL SYMBOLS USED

ON THE ENGINE OR

IN THIS MANUAL INCLUDE:

On Off

Fuel Shutoff

Read Owner’s

Manual

Stop Fuel

Choke

Safety Alert

Oil

Hazardous

Chemical

DANGER

• FreshStart fuel cap is designed to hold a cartridge which contains fuel stabilizer.

• IF SWALLOWED, call physician immediately. Do not induce vomiting. If inhaled,

remove to fresh air. In case of eye or skin contact, flush with water for 15 minutes.

• Store unopened cartridges in a cool, dry, well-ventilated area. Keep open cartridge

in fuel cap, and fuel cap closed on fuel tank when not in use.

Contents are HARMFUL OR FATAL IF SWALLOWED. Avoid contact to

eyes, skin, or clothing. Do not take internally. Avoid breathing the mist or

vapor. Overexposure to eyes or skin can cause irritation. Keep stabilizer

out of the reach of children.

Fuel stabilizer is a hazardous chemical. **

Your engine may be

equipped with a

FreshStartE fuel cap.

** Fuel stabilizer contains: 2,6-di-tert-butylphenol (128-39-2) and aliphatic petroleum distillate (64742-47-8).

SAFETY

Gasoline and its vapors are extremely

flammable and explosive.

Fire or explosion can cause severe burns

or death.

WARNING

WHEN ADDING FUEL

• Turn engine OFF and let engine cool at least 2

minutes before removing gas cap.

• Fill fuel tank outdoors or in well-ventilated area.

• Do not overfill fuel tank. Fill tank to approximately

1-1/2 inches below top of neck to allow for fuel

expansion.

• Keep gasoline away from sparks, open flames,

pilot lights, heat, and other ignition sources.

• Check fuel lines, tank, cap, and fittings frequently

for cracks or leaks. Replace if necessary.

WHEN STARTING ENGINE

• Make sure spark plug, muffler, fuel cap and air

cleaner are in place.

• Do not crank engine with spark plug removed.

• If fuel spills, wait until it evaporates before starting

engine.

• If engine floods, set choke to OPEN/RUN position,

place throttle in FAST and crank until engine starts.

WHEN OPERATING EQUIPMENT

• Do not tip engine or equipment at angle which

causes gasoline to spill.

• Do not choke carburetor to stop engine.

WHEN TRANSPORTING EQUIPMENT

• Transport with fuel tank EMPTY or with fuel shut-off

valve OFF.

WHEN STORING GASOLINE OR EQUIPMENT

WITH FUEL IN TANK

• Store away from furnaces, stoves, water heaters or

other appliances that have pilot light or other

ignition source because they can ignite gasoline

vapors.

Starting engine creates sparking.

Sparking can ignite nearby flammable

gases.

Explosion and fire could result.

WARNING

• If there is natural or LP gas leakage in area, do not

start engine.

• Do not use pressurized starting fluids because

vapors are flammable.

WARNING

Rapid retraction of starter cord (kickback) will

pull hand and arm toward engine faster than

you can let go.

Broken bones, fractures, bruises or sprains

could result.

• When starting engine, pull cord slowly until

resistance is felt, then pull rapidly.

• Remove all external equipment/engine loads

before starting engine.

• Direct coupled equipment components such as,

but not limited to, blades, impellors, pulleys,

sprockets, etc., must be securely attached.

WARNING

Rotating parts can contact or entangle

hands, feet, hair, clothing, or accessories.

Traumatic amputation or severe laceration

can result.

• Operate equipment with guards in place.

• Keep hands and feet away from rotating parts.

• Tie up long hair and remove jewelry.

• Do not wear loose-fitting clothing, dangling

drawstrings or items that could become caught.

SAFETY

Engines give off carbon monoxide, an

odorless, colorless, poison gas.

Breathing carbon monoxide can cause

nausea, fainting or death.

WARNING

• Start and run engine outdoors.

• Do not start or run engine in enclosed area, even if

doors or windows are open.

WARNING

Running engines produce heat. Engine

parts, especially muffler, become extremely

hot.

Severe thermal burns can occur on contact.

Combustible debris, such as leaves, grass,

brush, etc. can catch fire.

• Allow muffler, engine cylinder and fins to cool

before touching.

• Remove accumulated combustibles from muffler

area and cylinder area.

• Install and maintain in working order a spark

arrester before using equipment on forest-covered,

grass-covered, brush-covered unimproved land.

The state of California requires this (Section 4442

of the California Public Resources Code). Other

states may have similar laws. Federal laws apply

on federal land.

WARNING

Unintentional sparking can result in fire or

electric shock.

Unintentional start-up can result in en-

tanglement, traumatic amputation, or

laceration.

BEFORE PERFORMING ADJUSTMENTS OR

REPAIRS

• Disconnect spark plug wire and keep it away from

spark plug.

• Disconnect battery at negative terminal (only

engines with electric start).

WHEN TESTING FOR SPARK

• Use approved spark plug tester.

• Do not check for spark with spark plug removed.

ENGINE INFORMATION

TECHNICAL INFORMATION

POWER RATINGS: The power ratings for an individual engine

model are initially developed by starting with SAE (Society of Auto-

motive Engineers) code J1940 (Small Engine Power & Torque

Rating Procedure) (Revision 2002-05). Given both the wide array

of products on which our engines are placed, and the variety of en-

vironmental issues applicable to operating the equipment, it may

be that the engine you have purchased will not develop the rated

horsepower when used in a piece of power equipment (actual “on-

site” power). This difference is due to a variety of factors including,

but not limited to, the following: differences in altitude, tempera-

ture, barometric pressure, humidity, fuel, engine lubrication, maxi-

mum governed engine speed, individual engine to engine variabil-

ity, design of the particular piece of power equipment, the manner

in which the engine is operated, engine run-in to reduce friction

and clean out of combustion chambers, adjustments to the valves

and carburetor, and other factors. The power ratings may also be

adjusted based on comparisons to other similar engines utilized

in similar applications, and will therefore not necessarily match the

values derived using the foregoing codes.

ENGINE INFORMATION

1. Primer bulb

2. Air cleaner

3. Fuel fill

4. Finger guard

5. Spark plug wire

6. Carburetor

7. Rope handle

8. Fuel tank

9. Oil fill/Dipstick

10. Side drain plug (if equipped)

11. Muffler/Muffler guard (if equipped)

12. Spark arrester (if equipped)

13. Engine Model Type Code

xxxxx xxxx xx xxxxxxxx

GENERAL INFORMATION

This is a single cylinder, overhead valve (OHV), air-cooled engine.

It is a low emissions engine.

In the state of California, OHV Model Series 110000 and

120000 engines are certified by the California Air Resources

Board to meet emissions standards for 125 hours. Such certifi-

cation does not grant the purchaser, owner or operator of this

engine any additional warranties with respect to the perfor-

mance or operational life of this engine. This engine is war-

ranted solely according to the product and emissions warran-

ties stated elsewhere in this manual.

MODEL SERIES 110000

Bore 2-11/16 in. (68.26 mm). . . . . . . . . . . . . . . . . . . . . . . . .

Stroke 1-51/64 in. (46.00 mm). . . . . . . . . . . . . . . . . . . . . . .

Displacement 10.20 cu. in. (167.4 cc). . . . . . . . . . . . . . . .

MODEL SERIES 120000

Bore 2-11/16 in. (68.26 mm). . . . . . . . . . . . . . . . . . . . . . . . .

Stroke 2-3/64 in. (52.00 mm). . . . . . . . . . . . . . . . . . . . . . . .

Displacement 11.58 cu. in. (189.7 cc). . . . . . . . . . . . . . . . .

TUNE-UP SPECIFICATIONS

Armature air gap 0.006 - 0.014 in. (0.25 - 0.36 mm). . .

Spark plug gap 0.020 in. (0.51 mm). . . . . . . . . . . . . . . . . .

Valve clearance with valve springs installed and piston 1/4 in.

(6 mm) past top dead center (check when engine is cold).

See Repair Manual P/N 272147.

Intake 0.004 - 0.006 in. (0.10 - 0.15 mm). . . . . . . . . . . . .

Exhaust 0.004 - 0.008 in. (0.10 - 0.20 mm). . . . . . . . . . .

Note: For practical operation, the horsepower loading should

not exceed 85% of rated horsepower. Engine power will

decrease 3-1/2% for each 1,000 feet (300 meters) above

sea level and 1% for each 10° F (5.6° C) above 77° F

(25° C). It will operate satisfactorily at an angle up to 15°.

OIL

275749

CAUTION: This engine is shipped from Briggs &

Stratton without oil

. Check oil level before starting

engine. If you start the engine without oil, the engine

will be damaged beyond repair and will not be covered

under warranty.

OIL CAPACITY

Engine holds approximately 2/3 quart (22 ounces; 0.65 liter).

TYPE OF OIL TO USE

• Use a high quality detergent oil classified “For Service

SF, SG, SH, SJ” or higher, such as Briggs & Stratton

SAE 30, Part Number 100005 (20 oz) 100028 (48 oz), or

Briggs & Stratton Synthetic Oil, Part Number 100074

(32 oz).

• Do not use special additives.

• Choose a viscosity according to the table opposite.

Note: Synthetic oil meeting ILSAC GF-2, API

certification mark and API service symbol

(shown at left) with “SJ/CF ENERGY CON-

SERVING” or higher, is an acceptable oil at all

temperatures. Use of synthetic oil does not

alter required oil change intervals.

°F

-20 0 20 40 60 80 100

°C

-30 -20 -10 0 10 20 30 40

STARTING TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE

* CAUTION: Air cooled engines run hotter than

automotive engines. The use of non-synthetic

multi-viscosity oils (5W-30, 10W-30, etc.) in

temperatures above 40° F (4° C) will result in

higher than normal oil consumption. When using a

multi-viscosity oil, check oil level more frequently.

** CAUTION: SAE 30 oil, if used below 40° F (4° C),

will result in hard starting and possible engine bore

damage due to inadequate lubrication.

SAE Viscosity Grades

CHECKING AND ADDING OIL

• Check oil level before starting the engine.

• Check level daily, or after every eight (8) hours.

• Keep oil level at FULL.

CAUTION:

Do not overfill. Overfilling with oil may cause:

• Smoking

• Hard starting

• Spark plug fouling

• Oil saturation of air filter.

[1] Place engine level

and clean around oil

fill area.

[2] Remove dipstick and

wipe clean with cloth.

[3] Replace and tighten dipstick.

Remove and check oil level.

Oil Fill

FULL

[4] Oil level should be at FULL line

on dipstick.

[5] If needed, add oil slowly.

[6] Recheck oil level.

Do not over fill.

[7] Replace and tighten dipstick.

FUEL

TYPE OF FUEL TO USE

• Use clean, fresh, regular unleaded gasoline with a

minimum of 85 octane. Fresh fuel prevents gum from

forming in the fuel system or on essential carburetor parts.

Purchase fuel in quantity that can be used within 30 days.

• Do not use gasoline which contains Methanol.

• Do not mix oil with gasoline.

• If not equipped with a Fresh Start fuel cap, for engine

protection, use Briggs & Stratton Gasoline Additive

available from your Authorized Briggs & Stratton Dealer

(P/N 5041 or single use pouch).

• This engine is certified to operate on gasoline. Exhaust

Emission Control System: EM (Engine Modifications).

CAUTION: Some fuels, called oxygenated or reformu-

lated gasoline, are gasoline blended with alcohols or

ethers. Excessive amounts of these blends can damage

the fuel system or cause performance problems. If any

undesirable operating symptoms occur, use gasoline

with a lower percentage of alcohol or ether.

ADDING FUEL

[1] Remove cap. Fill tank to approximately 1-1/2

inches below top of neck to allow for fuel

expansion. Be careful not to overfill.

Briggs & Stratton Smart-fill fuel can fills to the

correct level and automatically shuts off, reducing

spills and emissions.

[2] Replace cap before starting.

Fuel Fill

Note: Remove and discard blue plug in fuel fill.

FRESH START FUEL CAP

DANGER

• IF SWALLOWED, call physician immediately.

Cartridge with Lift N’ PeelE tab.

Cartridge with tab removed.

Contents are HARMFUL OR FATAL IF SWALLOWED.

Avoid contact to eyes, skin, or clothing. Do not take

internally. Avoid breathing the mist or vapor. Overexposure

to eyes or skin can cause irritation. Keep stabilizer out of the

reach of children.

Fuel stabilizer is a hazardous chemical. **

** Fuel stabilizer contains 2,6-di-tert-butylphenol

(128-39-2) and aliphatic petroleum distillate (64742-47-8).

[1] Place cartridge

into fuel cap.

[2] Push to “snap”

cartridge into

place.

[3] Remove the

tab to expose

membrane.

[4] Reinstall fuel

cap on engine

fuel tank.

[5] Periodically check

the cartridge to

ensure there is still

stabilizer liquid

inside. If it is

empty, remove

cartridge and

replace.

STARTING

WARNING

• Do not use pressurized starting fluids.

• Vapors are flammable.

• Smoking,

• Hard starting,

• Spark plug fouling,

• Oil saturation of air filter.

CAUTION

If engine must be tipped to transport equipment, inspect or

remove grass, keep spark plug side of engine up

Transporting or tipping engine with spark plug down may

cause:

KEEP SPARK PLUG UP

STARTING AND OPERATING TIPS

♦ Store and fuel equipment in level position.

♦ Use fresh fuel. (See Fuel.)

♦ Use correct type of oil for expected starting

temperature. (See Oil.)

♦ Remove external equipment/engine loads. (See

equipment operating instructions.)

♦ Start lawn mower on hard surface or over previously

cut grass.

♦ Periodically remove grass buildup under mower

deck. (See Maintenance.)

♦ After engine has started, let it warm up several

seconds to several minutes, depending on outside

temperature.

♦ For maximum performance and life, operate engine

with choke (if equipped) in RUN and throttle in FAST.

REWIND (MANUAL) STARTER

TO START ENGINE

[1] Check oil level (see p. 7).

[2] Open fuel shut-off valve

(if equipped) 1/4 turn.

[3] Move throttle to FAST (if equipped).

Operate engine with throttle in FAST.

[4] Push stop switch (if equipped) to ON.

[5] Firmly push primer bulb 3 times OR

[6] Rotate choke knob or move choke

control lever to CHOKE position.

Primer Choke

[7] Close safety brake

handle on lawn mowers

and any other equipment

with this feature.

[8] Grasp rope handle. Pull slowly until

resistance is felt, then pull rapidly to

start engine and avoid kickback.

[9] Allow engine to

warm up.

If choke

equipped:

Slowly adjust to-

ward RUN posi-

tion. Wait until

engine runs

smoothly before

each choke

adjustment.

WARNING

STARTING AND STOPPING

ELECTRIC (KEY) STARTER (if equipped)

TO START ENGINE

[1] Check oil level (see p. 7).

[2] Open fuel shut-off valve

(if equipped) 1/4 turn.

[3] Move throttle to FAST (if

equipped). Operate en-

gine with throttle in

FAST position.

[4] Firmly push primer bulb 3 times OR

rotate choke knob or move choke control

lever to CHOKE position.

Primer Choke

[5] Close safety brake

handle on lawn mowers

and any other equipment

with this feature.

[6] Insert key and

turn to START.

CAUTION: To prolong starter life, use short

starting cycles (5 seconds maximum, then wait

one minute). Follow equipment manufacturer’s

recommendations for charging battery.

[7] Allow engine to warm up.

If choke equipped:

Slowly adjust toward

RUN position. Wait until

engine runs smoothly

before each choke

adjustment.

TO STOP ENGINE

CAUTION: Do not stop engine by moving choke

control to CHOKE. Backfire, fire or engine damage

could occur.

[1] Move throttle (if

equipped) to

SLOW, then re-

lease safety brake

control handle.

[2] Move throttle

(if equipped)

to SLOW,

then to STOP.

[3] Push stop switch (if equipped) to

OFF.

[4] Turn key to OFF. Remove key

and store out of reach of

children.

[5] Close fuel

shut-off valve

(if equipped).

MAINTENANCE

Regular maintenance will improve the performance and

extend the life of the engine. See any Authorized Briggs &

Stratton Dealer for service. Use only genuine Briggs &

Stratton parts. Other parts may not perform as well,

may damage the engine, and may result in injury. In

addition, use of other parts may void your warranty.

EMISSION CONTROL

Maintenance, replacement or repair of the emission

control devices and systems may be performed by any

nonroad engine repair establishment or individual.

However, to obtain no charge repairs under the terms and

provisions of the Briggs & Stratton warranty statement, any

service or emission control part repair or replacement must

be performed by a factory authorized dealer.

Task

Perform task at hourly

or calendar interval,

whichever comes first.

Every 8 Hours

or Daily

25 Hours or

Every Season

50 Hours or

Every Season

100 Hours or

Every Season

Yearly

Check oil level

Change oil

Change oil filter

(if equipped)

Service air cleaner

4**

Inspect spark arrester

(if equipped)

Replace spark plug

Replace in-line fuel filter

(if equipped)

Clean debris

4***

Clean air cooling system

4**

***

Check valve clearance

* Change oil after first 5 to 8 hours of use, then

every 50 hours or every season. Change oil every 25

hours when operating the engine under heavy load or

in high temperatures.

** Clean more often under conditions of dust or airborne

debris. Replace air cleaner parts, if very dirty.

*** On string trimmer applications:

- clean debris at each refueling, sooner if needed

(see CLEANING DEBRIS section);

- have qualified technician clean air cooling system

every 30 hours, every season, or sooner if needed,

especially in high debris conditions (see AIR

COOLING SYSTEM section).

CAUTION: Used oil is a hazardous waste product.

Dispose of used oil properly. Do not discard with

household waste. Check with your local authorities,

service center, or dealer for safe disposal/recycling

facilities.

CHANGING OIL

[1] Run engine until it runs

out of fuel. Otherwise,

fuel can leak out, creating

a fire/explosion hazard,

when you tip engine in

Step 4.

[2] Disconnect spark plug wire and keep it away from

spark plug.

[3] With engine OFF but still warm remove dipstick.

[4] Top oil drain, keep air cleaner above oil outlet.

Bottom or side oil drain (if equipped), keep engine

level. Drain oil into appropriate receptacle.

Note: Top oil drain is recommended method, however

oil can drain from side (if equipped) or bottom as shown.

[5] Place engine level. Add about 5/8 quart

(20 ounces: 0.6 liter) new oil. Fill to FULL line on

dipstick. Do not overfill.

[6] Replace dipstick.

WARNING

AIR

CLEANER

RATCHET

AND

EXTENSION

CUTTING

BLADE

OIL

DRAIN

PLUG

DRAIN

PLUGS

PIPE

3/8”

SQUARE

TOP OIL DRAIN

SIDE OIL DRAIN

(IF EQUIPPED)

BOTTOM OIL DRAIN

MAINTENANCE

AIR CLEANER

All engines have an air cleaner cartridge. The cartridge is

either flat or oval (see illustrations). In addition, some

engines have a pre-cleaner.

Pre-cleaner

To clean pre-cleaner (if equipped), separate it from

cartridge and wash in liquid detergent and water. Air dry

thoroughly. Do not oil pre-cleaner. Re-assemble dry

pre-cleaner on clean cartridge.

CAUTION: Do not use pressurized air or sol-

vents to clean cartridge. Pressurized air can

damage cartridge; solvents will dissolve

cartridge.

REMOVING and INSTALLING FLAT AIR CLEANER

[1] Loosen screw and tilt cover down.

[2] Remove air cleaner.

[3] Install clean (or new) air cleaner assembly inside

cover. Lip of pre-cleaner (if equipped) must be at

bottom of cartridge pleats.

[4] Insert cover’s tabs into slots in bottom of base.

[5] Tilt cover up into place.

[6] Tighten screw.

REMOVING and INSTALLING OVAL AIR CLEANER

[1] Loosen two screws and lift off cover.

[2] Remove air cleaner assembly (pre-cleaner, if

equipped, and cartridge) from base.

[3] Install clean (or new) air cleaner assembly in base. Air

cleaner must fit securely in base.

[4] Place cover over air cleaner.

[5] Tighten screws.

Flat Air Cleaner

SCREW

COVER

BASE

PRE-CLEANER

P/N 493537

CARTRIDGE

P/N 491588

or P/N 5043

CARTRIDGE

LIP

ASSEMBLE SO

CARTRIDGE LIP TOUCHES

BASE IN DIRECTION SHOWN

TABS AND SLOTS

PRE-CLEANER LIP

Oval Air Cleaner

ASSEMBLE SO THAT

CARTRIDGE LIP

SITS INSIDE BASE

2 SCREWS

COVER

BASE

CARTRIDGE

P/N 690610

PRE-CLEANER

P/N 273356

CHANGING OIL FILTER (if equipped)

Replace oil filter after every 100 hours of operation.

[1] After draining engine of used oil, fill with fresh oil.

[2] Before installing new filter, lightly oil filter gasket with

fresh, clean oil.

[3] Screw filter on by hand until gasket contacts oil filter

adapter.

[4] Tighten 1/2 to 3/4 turn more.

[5] Start and run engine at idle to check for leaks.

[6] Stop engine. Re-check oil level. Add oil if required.

OIL FILTER

MAINTENANCE

ENGINE AND ENGINE PARTS

We recommend that you see an authorized Briggs & Stratton Service Dealer for all maintenance and service of the engine

and engine parts. Use only genuine Briggs & Stratton parts.

WARNING

If you perform any maintenance on the engine, first disconnect the spark plug wire

from the spark plug, and disconnect the battery at the negative terminal (electric

starter engines only) to prevent unintentional sparking. Unintentional sparking can

result in fire or electric shock. Unintentional start-up can result in entanglement,

traumatic amputation or laceration. Use only correct tools.

WARNING

• Do not strike the flywheel with a hammer or hard object because the flywheel may

later shatter during operation.

• Do not tamper with governor spring, links or other parts to increase engine speed.

SPARK PLUG: Use only Briggs & Stratton Spark Tester

(part number 19368) to check for spark.

Note: In some areas, local law requires using resistor spark

plug to suppress ignition signals. If this engine was originally

equipped with resistor spark plug, use same type for

replacement.

.020” (0.51 mm)

WIRE GAGE

RESISTOR P/N 499608

MUFFLER

Replacement parts for the

muffler must be the same and

installed in the same position

as the original parts, other-

wise fire can occur.

If muffler is equipped with spark arrester screen, remove

screen for inspection. Replace screen if damaged or

plugged.

WARNING

FUEL SYSTEM

WARNING

Replacement parts for fuel

system (cap, hoses, tanks,

filters, etc.) must be the same

as original parts, otherwise

fire can occur.

REPLACE IN-LINE FUEL FILTER (if equipped)

[1] Disconnect spark plug wire and keep away from

spark plug.

[2] Drain fuel tank or close fuel shut-off valve before

replacing fuel filter. Otherwise, fuel can leak out,

creating a fire/explosion hazard.

FUEL FILTER

WARNING

FUEL HOSE CLAMPS

AIR COOLING SYSTEM

Over time debris may accumulate in cylinder cooling fins

and cannot be observed without partial engine disassem-

bly. We recommend that you have an authorized Briggs &

Stratton Service Dealer clean the air cooling system per

recommended intervals. Equally important is to keep top of

engine free from debris. See cleaning debris below.

VALVE CLEARANCE

Check valve clearance yearly. (See Tune-up Specifications

on page 6.)

MAINTENANCE

CLEANING DEBRIS

CAUTION: Do not use water to clean engine parts.

Water could contaminate fuel system. Use a brush

or dry cloth.

Engine parts should be kept

clean to reduce the risk of

overheating and ignition of

accumulated debris. This is

especially important if cutting

tall grass.

WARNING

Finger Guard

Linkage, Springs,

Controls

Muffler

Daily or before every use, clean grass, chaff or

accumulated debris from engine. Keep linkage, spring

and controls clean. Keep area around and behind

muffler free of any combustible debris.

Note: On string trimmer applications, clean accumulated

debris at each refueling, sooner if needed.

CLEAN

ADJUSTMENTS

THROTTLE ADJUSTMENT

If the engine does not start or if it runs roughly, the remote

throttle control may need adjustment. See your authorized

Briggs & Stratton dealer or follow the instructions below.

WARNING

Prevent unintentional starting.

Before performing adjustments:

• Remove spark plug wire from spark plug.

• Disconnect battery at negative terminal (only

engines with electric start).

TO ADJUST REMOTE THROTTLE*

[1] Loosen casing clamp screw.

[2] Move governor control lever, wire, and casing as

far as possible in direction shown.

[3] Move remote throttle control to FAST and tighten

casing clamp screw.

[4] Move throttle to STOP (if equipped).

GOVERNOR

CONTROL

LEVER

CASING

CLAMP

SCREW

WIRE &

CASING

* On some models the governor lever is fixed into position

and is not adjustable.

TO ADJUST STOP SWITCH

[1] Governor control lever should make good contact

with stop switch. Check operation of throttle.

[2] Readjust if necessary.

GOVERNOR

CONTROL

LEVER

STOP

SWITCH

CARBURETOR ADJUSTMENT

WARNING

The manufacturer of the equipment on which this

engine is installed specifies top speed at which the

engine will be operated. DO NOT EXCEED this speed.

Fuel/air mixture on this engine is not adjustable. If speed

adjustment is required, see your Authorized Briggs &

Stratton Service Dealer.

Note: Engines operated at about 3000 to 5000 feet (900 to

1500 meters) above sea level may require a high altitude

carburetor main jet. If erratic performance is observed,

contact a Briggs & Stratton Authorized Service Dealer for

cost to install/purchase a high altitude carburetor main jet, if

available.

SERVICE & STORAGE

PARTIAL LIST OF GENUINE BRIGGS &

STRATTON PARTS

BRIGGS & STRATTON

PART PART NO.

Flat air cleaner cartridge 491588 -or- 5043

Flat air cleaner pre-cleaner 493537

Oval air cleaner cartridge 690610

Oval air pre-cleaner 273356

Oil 100005 -or- 100028

Synthetic Oil 1000074

Fuel filter 298090 -or- 5018

Gas additive 5041

Resistor spark plug 499608

Spark plug wrench 89838

Spark tester 19368

Oil pump kit 5056

(uses standard electric drill to remove oil from engine quickly)

See an Authorized Briggs & Stratton Service Dealer. Each

one carries a stock of Genuine Briggs & Stratton Parts and

is equipped with special service tools. Trained mechanics

assure expert repair service on all Briggs & Stratton

engines. Only dealers advertising as “Authorized Briggs &

Stratton” are required to meet Briggs & Stratton standards.

When you purchase equipment powered by a

Briggs & Stratton engine, you are assured of

highly skilled, reliable service at more than

30,000 Authorized Service Dealers

worldwide, including more than 5,000 Master

Service Technicians. Look for these signs

wherever Briggs & Stratton service is offered.

You may locate your nearest Authorized Briggs & Stratton

Service Dealer in our dealer locator map on our web site

www.briggsandstratton.com or in the “Yellow Pages”

directory under “Lawn Mowers,” “Engines, Gaso-

line,” “Gasoline Engines,” or similar category.

Note: Walking fingers logo and “Yellow Pages” are regis-

tered trademarks in various jurisdictions.



An illustrated shop manual includes com-

mon specifications and detailed informa-

tion covering adjustment, tune-up and

repair of Briggs & Stratton single cylinder,

OHV, 4 cycle engines. It is available for

purchase from an Authorized Briggs &

Stratton Service Dealer or you can order it

from the factory. Write:

Briggs & Stratton Corporation

Attn: Service Division

P. O. Box 1144

Milwaukee, WI 53201

Part No. 272147

STORAGE

Engines stored over 30 days need special attention.

[1] To prevent gum from forming in fuel system or on

essential carburetor parts:

a) if fuel tank contains oxygenated or reformulated

gasoline (gasoline blended with an alcohol or an

ether), run engine until it stops from lack of fuel, or b) if

fuel tank contains gasoline, either run engine until it

stops from lack of fuel, or add a gasoline additive to the

gas in the tank. (See parts list. Single-use pouches of

gas additive are available from your service dealer.) If

you use a gas additive, run the engine for several

minutes to circulate the additive through the carburetor.

Then, engine and fuel can be stored up to 24 months.

[2] While engine is still warm, change oil.

[3] Remove spark plug and pour about 1/2 oz. (15 ml) of

engine oil into cylinder. Replace spark plug and crank

slowly to distribute oil.

[4] Clean engine of surface debris, chaff or grass.

WARNING

[5] Store in a clean, dry area.

Do not store in same area

as a stove, furnace, water

heater, or other appliance

that uses a pilot light or

has a device that can

create a spark.

Engwnty1-03 - page 1 (Black)

Screen angle and frequency: 45.0000, 150.0000

               

      

LIMITED WARRANTY

Briggs & Stratton Corporation will repair or replace, free of charge, any part(s) of the engine that is defective in material or workmanship or both.

Transportation charges on parts submitted for repair or replacement under this warranty must be borne by purchaser. This warranty is effective for the

time periods and subject to the conditions stated below. For warranty service, find the nearest Authorized Service Dealer in our dealer locator map

at www.briggsandstratton.com, or by calling 1-800-233-3723, or as listed in the ‘Yellow Pages’.

THERE IS NO OTHER EXPRESS WARRANTY. IMPLIED WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR A

PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR FROM PURCHASE, OR TO THE EXTENT PERMITTED BY LAW ANY AND ALL IMPLIED

WARRANTIES ARE EXCLUDED. LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES ARE EXCLUDED TO THE EXTENT

EXCLUSION IS PERMITTED BY LAW. Some states or countries do not allow limitations on how long an implied warranty lasts, and some states or

countries do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation and exclusion may not apply to you.

This warranty gives you specific legal rights and you may also have other rights which vary from state to state and country to country.





r

 



(Sleeve Bore)

!"



(Kool Bore)

!#  $

%&r

%!

%45

'

"

Commercial Use

2 years

90 days

1 year

Consumer Use

2 years 2 years

90 days

1 year

( )(

 )*



1 year

* Note the following special warranty periods: 2 years for Classic engines in the European Union and Eastern European countries, for all consumer products in

the European Union, and for emission control systems on engines certified by EPA and CARB. 5 years for consumer use, 90 days for commercial use of Touch-N-

Mow starter on Quantum and Intek engines. Engines used in competitive racing or on commercial or rental tracks are not warrantied.

The warranty period begins on the date of purchase by the first retail consumer or commercial end user, and continues for the period of time stated in the table

above. “Consumer use” means personal residential household use by a retail consumer. “Commercial use” means all other uses, including use for commercial,

income producing or rental purposes. Once an engine has experienced commercial use, it shall thereafter be considered as a commercial use engine for pur-

poses of this warranty.

NO WARRANTY REGISTRATION IS NECESSARY TO OBTAIN WARRANTY ON BRIGGS & STRATTON PRODUCTS. SAVE YOUR PROOF OF PURCHASE

RECEIPT. IF YOU DO NOT PROVIDE PROOF OF THE INITIAL PURCHASE DATE AT THE TIME WARRANTY SERVICE IS REQUESTED, THE

MANUFACTURING DATE OF THE PRODUCT WILL BE USED TO DETERMINE THE WARRANTY PERIOD.

        

       

       

      

     ! "  

         #

      

        

          

   

$           

        

 #         

    !   $    

!      %    

        & 

      

           

      

 

' #      

      (  

      "      

 

 

&          

         

          

          

         #

         

        

 

!   "   

# $!      

 ! %  !! ! "   &

  !  '   % 



) *+,-' ./' 0 *+& &1& +' 2,&

,+$3$2- +$33  &+&&,2 *+&

4 '      

     

  5.  6

7 -#     # 

        

 5/   8    

 !  * 2 9:;)6

; *     #   

     

        

5#       <=  

+      

6 ,$- 3+     

 '        

  + ,  

$

9 +  %     

      

       

>          

      

 8     8 

    5 

   8  ,8!   

 8    6 +

,   $

? *   8  

          

        

        

 5.       

   6 + , 

 $

< '    #  "

       

      

    

   # 8  

  

@    # #   #  

%          

" 8 

): + 8  %   

)) '      

       

        

       

 

    !"!   !!

!  !(  )"" * + ,&

  -!( + .    !

/0  1"2   !  

/" 32  /3 "2 /4

52   "&

( (  

Engwnty1-03 - page 2 (Black)

Screen angle and frequency: 45.0000, 150.0000

  ! !'!! +,- . /!  !" ! +,

 . (  0!& !"! "1 +(22 ,

&! !! 1& 1 & +#3 )/" 1 .  4!,

EMISSION CONTROL WARRANTY COVERAGE IS APPLICABLE TO CERTIFIED ENGINES PURCHASED IN CALIFORNIA IN 1995 AND THERE-

AFTER, WHICH ARE USED IN CALIFORNIA, AND TO CERTIFIED MODEL YEAR 1997 AND LATER ENGINES WHICH ARE PURCHASED AND

USED ELSEWHERE IN THE UNITED STATES (AND AFTER JANUARY 1, 2001 IN CANADA).

/!  (  &! !! )/" 1 &

The California Air Resources Board (CARB), U.S.

EPA and B&S are pleased to explain the Emission

Control System Warranty on your model year

2002 and later small off-road engine (SORE). In

California, new small off-road engines must be de-

signed, built and equipped to meet the State’s

stringent anti-smog standards.

Elsewhere in the United States, new non-road,

spark-ignition engines certified for model year

1997 and later must meet similar standards set

forth by the U.S. EPA. B&S must warrant the emis-

sion control system on your engine for the periods

of time listed below, provided there has been no

abuse, neglect or improper maintenance of your

small off-road engine.

Your emission control system includes parts

such as the carburetor, air cleaner, ignition sys-

tem, muffler and catalytic converter. Also in-

cluded may be connectors and other emission

related assemblies.

Where a warrantable condition exists, B&S will

repair your small off-road engine at no cost to

you including diagnosis, parts and labor.

  ! &! !! )/" 1 !0

Small off-road engines are warranted relative to emission control parts defects for a period of two years, subject to provisions set forth below. If any

covered part on your engine is defective, the part will be repaired or replaced by B&S.

#3 1 '!4

As the small off-road engine owner, you are re-

sponsible for the performance of the required

maintenance listed in your Operating and Main-

tenance Instructions. B&S recommends that

you retain all your receipts covering mainte-

nance on your small off-road engine, but B&S

cannot deny warranty solely for the lack of re-

ceipts or for your failure to ensure the perfor-

mance of all scheduled maintenance.

As the small off-road engine owner, you should

however be aware that B&S may deny you war-

ranty coverage if your small off-road engine or a

part has failed due to abuse, neglect, improper

maintenance or unapproved modifications.

You are responsible for presenting your small

off-road engine to an Authorized B&S Service

Dealer as soon as a problem exists.

The undisputed warranty repairs should be

completed in a reasonable amount of time, not

to exceed 30 days.

If you have any questions regarding your war-

ranty rights and responsibilities, you should con-

tact a B&S Service Representative at

1-414-259-5262.

The emission warranty is a defects warranty.

Defects are judged on normal engine perfor-

mance. The warranty is not related to an in-use

emission test.

  ! &! !! )/" 1 !0!

The following are specific provisions relative to your Emission Control Defects Warranty Coverage. It is in addition to the B&S engine warranty for non-

regulated engines found in the Operating and Maintenance Instructions.

1. Warranted Parts

Coverage under this warranty extends only

to the parts listed below (the emission con-

trol systems parts) to the extent these parts

were present on the engine purchased.

a. Fuel Metering System

• Cold start enrichment system

• Carburetor and internal parts

• Fuel Pump

b. Air Induction System

• Air cleaner

• Intake manifold

c. Ignition System

• Spark plug(s)

• Magneto ignition system

d. Catalyst System

• Catalytic converter

• Exhaust manifold

• Air injection system, Pulse valve

e. Miscellaneous Items

• Vacuum, temperature, position,

time sensitive valves

and switches

• Connectors and assemblies

2. Length of Coverage

B&S warrants to the initial owner and each

subsequent purchaser that the Warranted

Parts shall be free from defects in materials

and workmanship which caused the failure

of the Warranted Parts for a period of two

years from the date the engine is delivered to

a retail purchaser.

3. No Charge

Repair or replacement of any Warranted

Part will be performed at no charge to the

owner, including diagnostic labor which

leads to the determination that a Warranted

Part is defective, if the diagnostic work is

performed at an Authorized B&S Service

Dealer. For emissions warranty service

contact your nearest Authorized B&S Ser-

vice Dealer as listed in the “Yellow Pages”

under “Engines, Gasoline,” “Gasoline En-

gines,” “Lawn Mowers,” or similar category.

4. Claims and Coverage Exclusions

Warranty claims shall be filed in accordance

with the provisions of the B&S Engine War-

ranty Policy. Warranty coverage shall be ex-

cluded for failures of Warranted Parts which

are not original B&S parts or because of

abuse, neglect or improper maintenance as

set forth in the B&S Engine Warranty Policy.

B&S is not liable to cover failures of War-

ranted Parts caused by the use of add-on,

non-original, or modified parts.

5. Maintenance

Any Warranted Part which is not scheduled

for replacement as required maintenance or

which is scheduled only for regular inspec-

tion to the effect of “repair or replace as nec-

essary” shall be warranted as to defects for

the warranty period. Any Warranted Part

which is scheduled for replacement as re-

quired maintenance shall be warranted as to

defects only for the period of time up to the

first scheduled replacement for that part. Any

replacement part that is equivalent in perfor-

mance and durability may be used in the per-

formance of any maintenance or repairs.

The owner is responsible for the perfor-

mance of all required maintenance, as de-

fined in the B&S Operating and Maintenance

Instructions.

6. Consequential Coverage

Coverage hereunder shall extend to the fail-

ure of any engine components caused by

the failure of any Warranted Part still under

warranty.

   '   / , ,  , & ! *A  84;?)?? 5, * *6

6,325,036

6,284,123

6,260,529

6,230,678

6,202,616

6,116,212

6,077,063

6,064,027

6,014,808

5,894,715

5,852,951

5,823,153

5,819,513

5,813,384

5,765,713

5,645,025

5,642,701

5,619,845

5,606,948

5,606,851

5,548,955

5,546,901

5,503,125

5,501,203

5,497,679

5,320,795

5,271,363

5,269,713

5,265,700

5,243,878

5,235,943

5,197,425

5,197,422

5,191,864

5,188,069

5,186,142

5,138,996

5,086,890

5,070,829

5,058,544

5,040,644

5,009,208

4,996,956

4,977,879

4,971,219

4,895,119

4,819,593

4,719,682

4,633,556

4,630,498

4,522,080

4,520,288

4,512,499

4,453,507

4,430,984 DES. 308,871

DES. 308,872

DES. 309,457

DES. 356,951

DES. 361,771

DES. 375,963

(Cette page ne s’applique que pour le Canada et les Etats−Unis)

La Corporation Briggs & Stratton (B&S), le California Air Resources Board (CARB)

et le Bureau de protection environnementale des EtatsUnis (US EPA)

Garantie sur le système d’échappement (Garantie contre les défectuosités, droits et obligations du propriétaire)

LA GARANTIE SUR LE SYSTÈME D’ÉCHAPPEMENT EST APPLICABLE SUR LES MOTEURS

CERTIFIÉS ACHETÉS EN CALIFORNIE EN 1995 ET LES ANNÉES SUIVANTES ET QUI SONT UTI−

LISÉS EN CALIFORNIE, AINSI QU’AUX MODÈLES CERTIFIÉS DE 1997 ET LES ANNÉES SUI−

VANTES QUI ONT ÉTÉ ACHETÉS ET UTILISÉS AILLEURS AUX ETATS−UNIS (ET APRÉS LE 1ER

JANVIER 2001 AU CANADA).

Déclaration de garantie sur le système d’échappement pour la Californie, les EtatsUnis

Le California Air Resources Board (CARB), le Bureau américain de protection environnementale

(U.S. EPA) et B& S sont heureux d’expliquer la garantie sur le système d’échappement des petits

moteurs hors−route de votre modèle 2000 et des années ultérieures (SORE). En Californie, les

nouveaux petits moteurs hors route doivent être conçus, construits et équipés pour rencontrer les

standards rigoureux d’antipollution. Ailleurs aux Etats−Unis, les nouveaux moteurs hors route à

bougie d’allumage certifiés pour les modèles de 1997 et plus, doivent rencontrer des normes simi−

laires mises de l’avant par le U.S. EPA. Briggs & Stratton garantit le système de contrôle d’échap−

pement de votre moteur pour la période de temps mentionnée ci−contre, sauf s’il a fait l’objet

d’abus, de négligence ou d’un entretien inapproprié.

Votre système de contrôle d’échappement comprend des pièces telles que le carburateur, le filtre à

air, le système d’ignition, le silencieux et le convertisseur catalytique. Il peut aussi comprendre les

connecteurs et autres pièces reliées à l’émission.

Lorsqu’il y a condition à garantie, B&S réparera gratuitement votre petit moteur hors−route incluant

le diagnostic, les pièces et la main d’œuvre.

Couverture de garantie Briggs & Stratton contre toute défectuosité du système de contrôle d’échappement

Les petits moteurs hors route sont garantis contre la défectuosité des pièces du système de contrô−

le d’échappement pour une période de 2 ans, sujette aux conditions stipulées ci−contre. Si n’impor−

te quelle pièce de votre moteur couverte par cette garantie est défectueuse, elle sera réparée ou

remplacée par B&S.

Responsabilités du propriétaire

En tant que propriétaire d’un petit moteur hors route, vous êtes responsable de veiller à l’exécution

de l’entretien requis tel que stipulé dans votre manuel d’opération et d’entretien. B&S vous recom−

mande de conserver tous les reçus couvrant les travaux d’entretien de votre petit moteur hors rou−

te, mais B&S ne peut refuser la garantie en raison d’absence de reçus ou pour défaut d’avoir suivi

tout l’échéancier du programme d’entretien.

En tant que propriétaire d’un petit moteur hors route, vous devez être informé que B&S peut refuser

d’honorer cette garantie si la défectuosité de votre moteur ou d’une partie de votre moteur est due à

un emploi abusif, une négligence, un entretien incorrect ou une modification non approuvée.

Vous avez la responsabilité d’apporter votre petit moteur hors route à un détaillant autorisé B&S

aussitôt que survient un problème. Les réparations sous garantie doivent être complétées dans un

délai raisonnable ne devant pas excéder 30 jours.

Si vous avez des questions relativement à votre garantie, vos droits et responsabilités, veuillez

communiquer avec un représentant de service B&S au numéro 1−414−259−5262.

La garantie du système d’échappement est une garantie contre les défectuosités. Les défectuosi−

tés sont jugées en fonction d’une utilisation normale du moteur. La garantie n’est pas reliée à un

test d’échappement effectué à l’intérieur.

Dispositions de la garantie du système d’échappement Briggs & Stratton

Ce qui suit concerne les dispositions spécifiques relativement à votre garantie sur le système de contrôle d’échappement. C’est une addition à la garantie B&S pour les moteurs non réglementés contenue

dans le manuel d’entretien et d’utilisation.

1. Pièces sous garantie

La couverture de cette garantie ne s’applique que sur les pièces listées ci−contre (les parties

du système de contrôle d’échappement) dans la mesure où ces pièces étaient présentes sur le

moteur au moment de l’achat.

a. Système de dosage du carburant

• Système d’enrichissement de démarrage à froid

• Carburateur et parties internes

• Pompe à essence

b. Système d’induction d’air

• Filtre à air

• Tubulure d’admission

c. Système d’ignition

• Bougies d’allumage

• Système d’allumage électromagnétique

d. Système catalyseur

• Convertisseur catalytique

• Collecteur d’échappement

• Système d’injection d’air ou à pulsion

e. Autres pièces utilisées dans les systèmes ci−haut mentionnés

• Soupapes et interrupteurs de dépression, de température, de position.

• Connecteurs et assemblages.

2. Durée de la couverture

B&S garantit le propriétaire initial et tous les acheteurs subséquents que les pièces sous ga−

rantie sont exemptes de vice de matière ou de fabrication qui pourraient causer des défectuosi−

tés des pièces sous garantie pour une période de deux ans à partir de la date à laquelle le mo−

teur a été livré à l’acheteur.

3. Aucuns Frais

La réparation ou le remplacement de toute pièce sous garantie sera effectuée sans aucuns

frais pour le propriétaire, incluant les frais de main d’œuvre pour le diagnostic afin de détermi−

ner si la pièce sous garantie est défectueuse, conditionnel à ce que le diagnostic soit effectué

chez un détaillant autorisé B&S. Pour la garantie relative au système d’échappement, commu−

niquez avec le détaillant autorisé B&S le plus proche tel que listé dans les pages jaunes de

votre localité sous la rubrique moteur à essence, tondeuse ou autre catégorie similaire.

4. Réclamations et exclusions de la couverture.

Les réclamations de garantie doivent être complétées en accord avec les dispositions de la

politique de garantie B&S. La garantie ne couvre pas les défectuosités de pièces qui ne sont

pas des pièces d’origine B&S ou dans le cas d’abus, négligence ou d’un entretien inapproprié.

La garantie B&S ne couvre pas les défectuosités de pièces sous garantie qui ont fait l’objet

d’ajouts, ont été modifiées ou de pièces qui ne sont pas des pièces B&S d’origine.

5. Entretien

Toute pièce sous garantie qui n’est pas remplacée au moment requis selon le manuel d’entre−

tien ou qui est planifiée seulement pour une inspection régulière sous la mention « réparer ou

remplacer si nécessaire » est garantie contre toute défectuosité pour la période de garantie.

Toute pièce sous garantie qui est planifiée pour un remplacement tel que requis dans l’entre−

tien est garantie contre toute défectuosité seulement pour la période de temps qui va jusqu’au

premier remplacement prévu pour cette pièce. Toute pièce de remplacement équivalente en

performance et durabilité peut être utilisée pour l’entretien ou la réparation. Le propriétaire est

responsable de l’exécution de tout entretien requis tel que défini dans le manuel d’instruction

B&S sur l’entretien et la réparation.

6. Couverture indirecte

La couverture ci−contre s’étend à toute défectuosité des composantes du moteur causée par

la défectuosité de n’importe quelle pièce couverte par la garantie et dont la garantie est encore

en vigueur.

Consultez les informations sur la période de durabilité d’émission et l’INDICE d’air sur l’étiquette d’émission de votre moteur

Les moteurs qui sont certifiés conformes aux normes standards d’émission du California Air Resources Board (CARB) Tier 2, doivent afficher l’information concernant la période de durabilité du système

d’émission et l’INDICE d’air. Cette information est indiquée sur les étiquettes apposées sur les moteurs par Briggs & Stratton. L’étiquette du moteur indiquera les renseignements concernant la certification.

La période de durabilité d’émission indique le nombre d’heures d’utilisation normale pour lequel le moteur est certifié conforme aux normes d’émission sous réserve d’un entretien approprié tel qu’indiqué dans

le manuel d’opération et d’entretien. Les catégories suivantes sont utilisées :

Modéré le moteur est certifié conforme pour 125 heures d’utilisation normale.

Intermédiaire le moteur est certifié conforme pour 250 heures d’utilisation normale.

Prolongé le moteur est certifié conforme pour 500 heures d’utilisation normale.

Par exemple, une tondeuse de modèle standard est utilisée environ 20 à 25 heures par année. Par conséquent, la période de durabilité d’émission d’un moteur dans la catégorie intermédiaire pour ce type de

tondeuse équivaut à 10 à 12 ans.

L’indice d’air est un nombre qui décrit le niveau relatif d’émission pour une catégorie spécifique de moteur. Plus l’indice d’air est bas, plus le moteur est écologique. Cette information est indiquée sous une

forme graphique sur l’étiquette d’émission.

À compter du 1

juillet 2000, surveillez la période de conformité d’émission sur les étiquettes

Après le 1

juillet 2000, certains moteurs B&S seront certifiés conformes aux normes environnementales d’émission standard du United States Environmental Protection Agency (US EPA) Phase 2. Pour les

moteurs certifiés pour la Phase 2, la période de conformité d’émission mentionnée sur les étiquettes indique le nombre d’heures d’utilisation pour lequel le moteur rencontre les normes fédérales. Pour les

moteurs de force moindre que 225 cc, la catégorie C = 125 heures, B = 250 heures et A = 500 heures. Pour les moteurs de 225 cc et plus, la catégorie C = 250 heures, B = 500 heures et A = 1000 heures.

Le remplacement du moteur portant le modèle de série 110000 est 164 cc. Le remplacement du moteur portant le modèle de série 120000 est 190 cc.

Ceci est une représentation des étiquettes d’émission

que vous retrouverez sur les moteurs certifiés :

CE MOTEUR EST CONFORME AUX NORMES

ANTIPOLLUTION 2000 - 2001 DE CALIFORNIE

POUR LES PETITS MOTEURS HORS ROUTE ET

AUX NORMES ENVIRONNEMENTALES

AMÉRICAINES (EPA PHASE 2) POUR LES

PETITS MOTEURS HORS ROUTE. CONSULTEZ

LE MANUEL DU PROPRIÉTAIRE POUR LES

SPÉCIFICATIONS, L’ENTRETIEN ET LES

AJUSTEMENTS. CONFORME À LA PÉRIODE