Sanyo HT28745 Le manuel du propriétaire

AS

Model Nos:

No. de Modelo:

N

o

de modèle :

HT27745

HT28745

“As an ENERGY STAR

®

Partner, Sanyo

Manufacturing Corporation has determined

that this product meets the ENERGY STAR

®

guidelines for energy efficiency.”

As Real

As It Gets!

“Read this manual before assembling (or using) this product.”

Need assistance?

Visit our website at www.sanyoctv.com

or Call toll free 1.800.877.5032

We can Help!

Owner’s Manual

ENGLISH

Table of Contents . . . . . 3

Manual de Instrucciónes

ESPAÑOL

Contenido . . . . . . . . . . 25

Manuel d’instructions

FRANÇAIS

Table des matières . . . 49

Printed in U.S.A. SMC, March 2005

Impreso en U.S.A. SMC, Marzo 2005

Imprimé aux é.-U. SMC, mars 2005

Part No. / No. de Parte /

N

o

de pièce : 1AA6P1P4785––

Service Code / Código de Servicio /

Code de service : 610 319 9245

HT28745

HT27745

Importado Por : Comercializadora México

Americana, S. DE R.L. DE C.V.

Nextengo N

o

78

Col. Santa Cruz Acayucan

Del. Azcapotzalco, México D.F. C.P. 02770

RFC CMA 9109119L0

Telefono: 55-5328-3500

MediaStack-ATSC

the DTV software embedded in

by Zentek Technology, Inc.

Positioning the Appliance

1. Do not place your appliance on an unstable cart, stand, shelf or table. Serious

injury to an individual, and damage to the appliance, may result if it should

fall. Your salesperson can recommend approved carts and

stands or shelf and wall mounting instructions. An appliance and

cart combination should be moved with care. Quick stops, exces-

sive force, and uneven surfaces may cause the appliance and

cart combination to overturn.

2. Slots and openings in the cabinet and in the back or bottom are provided for

ventilation. To ensure reliable operation of the appliance and to protect it

from overheating, these openings must not be blocked or covered. The open-

ings should never be covered with a cloth or other material, and the bottom

openings should not be blocked by placing the unit on a bed, sofa, rug, or

other similar surface. This appliance should never be placed near or over a

radiator or heat register. This appliance should not be placed in a built-in

installation such as a bookcase unless proper ventilation is provided.

3. Do not expose the appliance to rain or use near water . . . for example, near

a bathtub, swimming pool, kitchen sink, in a wet basement, etc.

Hooking Up Outdoor Antenna

LIGHTNING PROTECTION FOR YOUR ANTENNA AND SET AS PER NATIONAL

ELECTRICAL CODE INSTRUCTIONS.

4. If an outside antenna is connected to the receiver, be sure the antenna system

is grounded so as to provide some protection against voltage surges and built

up static charges. Article 810 of the National Electrical Code, ANSI/NFPA 70,

provides information with respect to proper grounding of the mast and support-

ing structure, grounding of the lead in wire to an antenna discharge unit, size of

grounding conductors, location of antenna discharge unit, connection to

grounding electrodes, and requirements for the grounding electrode.

An outside antenna system should not be located in the vicinity of overhead

power lines or other electric light or power circuits, or where it can fall into

such power lines or circuits. When installing an outside antenna system

extreme care should be taken to keep from touching such power lines or cir-

cuits as contact with them might be fatal.

Plug in the power cord

5. This product should be operated only from the type of power source indi-

cated on the marking label. If you are not sure of the type of power supply to

your home, consult your product dealer or local power company. This

product is equipped with a three-wire grounding-type plug, a plug having a

third (grounding) pin. This plug will only fit into a grounding-type power outlet.

This is a safety feature. If you are unable to insert the plug into the outlet,

contact your electrician to replace your obsolete outlet. Do not defeat the

safety purpose of the grounding-type plug.

6. Power-supply cords should be routed so that they are not likely to be walked

on or pinched by items placed upon or against them, paying particular atten-

tion to cords at plugs, convenience receptacles, and the point where they

exit from the product.

Cleaning

7. Before cleaning, unplug the unit from the wall outlet. Do not apply liquid

cleaners or aerosol cleaners directly to the unit. Use a dry cloth for cleaning.

Service & Repair

8. Unplug the appliance from the wall outlet and refer servicing to qualified

service personnel under the following conditions:

A. If the power cord or plug is damaged or frayed.

B. If liquid has been spilled into the appliance.

C. If the appliance has been exposed to rain or water.

D. If the appliance has been dropped or the cabinet has been damaged.

E. If the appliance exhibits a distinct change in performance.

F. If the appliance does not operate normally by following the operating

instructions, adjust only those controls that are covered in the operating

instructions. Improper adjustment of other controls may result in damage and

will often require extensive work by a qualified technician to restore the

appliance to normal operation.

9. Upon completion of any service or repair, request the service technician’s

assurance that only Factory Authorized Replacement Parts that have the

same characteristics as the original parts were used, and that routine safety

checks have been performed to determine that the appliance is in safe oper-

ating condition. Unauthorized substitutions may result in fire, electrical

shock, or other hazards.

10. Never add accessories that have not been specifically designed for use with

this appliance as they may cause hazards.

11. For added protection during a lightning storm, or when the set is left unat-

tended and unused for long periods of time, unplug it from the wall outlet and

disconnect the antenna. This will prevent damage to the set due to lightning

or power line surges.

12. Never push objects of any kind into this product through openings as they

may touch dangerous voltage points or short-out parts that could result in a

fire or electric shock. Never spill liquid of any kind on the product.

CAUTION

RISK OF ELECTRIC SHOCK DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR

BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL.

THIS SYMBOL INDICATES THAT DANGEROUS VOLTAGE CONSTITUT-

ING A RISK OF ELECTRIC SHOCK IS PRESENT WITHIN THIS UNIT.

THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT OPERATING

AND MAINTENANCE INSTRUCTIONS IN THE LITERATURE ACCOMPA-

NYING THIS UNIT.

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

IMPORTANT SAFETY INSTRUCTIONS

CAUTION: PLEASE ADHERE TO ALL WARNINGS ON THE PRODUCT AND IN THE OPERATING INSTRUCTIONS. BEFORE OPERATING THE PRODUCT,

PLEASE READ ALL OF THE SAFETY AND OPERATING INSTRUCTIONS. RETAIN THIS LITERATURE FOR REFERENCE. Follow all instructions...

EXAMPLE OF ANTENNA GROUNDING

ACCORDING TO NATIONAL

ELECTRICAL CODE,

ANSI/NFPA 70

2

Need help?

Visit our Web site at www.sanyoctv.com or Call 1-800-877-5032

“Note to CATV system installer:

This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the

NEC that provides guidelines for proper grounding and, in particular, specifies that the cable

ground shall be connected to the grounding system of the building, as close to the point of

cable entry as practical.”

CHILD SAFETY

Sanyo is committed to making home entertainment safe and enjoyable.

Always use an appropriate table or stand when positioning your DTV.

Use appropriate brackets, braces, or straps to anchor your furniture in

place. But never screw anything directly to the television.

Do not place televisions on dressers, shelves, desks, carts, etc. where

curious or excited children could pull, push, or otherwise cause the unit

to fall and cause personal injury.

Never place toys or other items on top of

the DTV that could pique children’s

curiosity causing them to climb about the

furniture.

Always use stands that are designed to

support the size and combined weight of

your television and other electronic

devices.

Welcome to the World of Sanyo

Thank you for purchasing this Sanyo High-Definition Digital

Television. You made an excellent choice for Performance,

Reliability, Features, Value, and Styling.

Important Information

Before installing and operating this DTV, read this manual

thoroughly. This DTV provides many convenient features and

functions. Operating the DTV properly enables you to manage

those features and maintain it in good condition for many years

to come.

If your DTV seems to operate improperly, read this manual

again, check operations and cable connections and try the

solutions in the “Helpful Hints” section, page 22 of this

manual. If the problem still persists, visit our website at

www.sanyoctv.com or call 1.800.877.5032. We can help!

Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . 2

To the Owner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

First-Things-First (Required Initial Setup) . . . . . . . . . . . . . . . . 5

Digital (DTV) Antenna Connection . . . . . . . . . . . . . . . . . . . . . . . . 5

Analog (RF) Antenna Connection . . . . . . . . . . . . . . . . . . . . . . . . . 5

Installing Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Channel Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Auto Clock Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Antenna Selection (Optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

DTV Back—Jacks Locations & Functions . . . . . . . . . . . . . . . . . 7

Glossary of Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Choose Your Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Digital A/V Connections

Using the Component Jacks to connect a DVD Player

or Other Digital Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Connecting Digital Audio Out Jacks to a Multi-Channel Receiver . . 9

Analog A/V Connections

Using the Analog Video Jacks to connect a VCR

(or Other Analog Device) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Connecting Analog Audio Out Jacks to a

Stereo Amplifier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Using the Remote Control . . . . . . . . . . . . . . . . . . . . . . . 11 ~ 12

DTV Adjustment and Setup

How to Operate the On-Screen Menu . . . . . . . . . . . . . . . . . . . . . 13

Menu Navigation Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Channel Setup Options:

Channel Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Digital Cable Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Digital Add-On Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Antenna Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Channel Scan Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Initial Channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Closed-Captioning Options:

Changing the Look of Digital Captioning

On-Screen Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

To View Captions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

V-Guide (Parental Control) Options:

To Block Movies or TV Programs . . . . . . . . . . . . . . . . . . . . 18

To Temporarily Unblock Movies or TV Programs . . . . . . . . . . 18

To Unblock Movies or TV Programs . . . . . . . . . . . . . . . . . . 18

TV Ratings (Age and Content-Based)

Symbol Explanation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

MPAA Movie Ratings (Age-Based)

Symbol Explanation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Setup Menu Options:

Auto Date /Time Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Manual Date / Time Setting . . . . . . . . . . . . . . . . . . . . . . . . . 19

Digital Audio Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

DTV Speakers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Menu Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Picture/Sound Adjustment Options:

Preset Picture and Sound Options . . . . . . . . . . . . . . . . . . . . 20

Manual Picture and Sound Adjustment . . . . . . . . . . . . . . . . 21

Color Enhancer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Scan Velocity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Helpful Hints (Problems/Solutions) . . . . . . . . . . . . . . . . . . . . 22

Warranty (Mexico) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Warranty (U.S.A. and Canada) . . . . . . . . . . . . . . . . . . . . . . . 24

Care and Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

CONTENTS

3

Need help?

Visit our Web site at www.sanyoctv.com or Call 1-800-877-5032

TO THE OWNER

 27” / 28” High-Definition Digital True Flat-screens

 Trilingual Menu Options (English, French, or Spanish)

 Built-in Digital and Analog Tuners

 Automatic Channel Search

 Auto Shut Off (no signal received after 15 minutes)

 3-Line Digital Comb Filter (for better picture detail)

 Adjustable Scan Velocity Modulation

 V-Chip for Movies and TV guidelines rating limits (parental control)

 Closed-Captioning: Analog EIA-608B

Digital EIA-708B

 Audio Modes: DTV—Main and Sub

NTSC—Stereo, Mono, and SAP

 Front Surround Sound

 Bass / Treble Sound

 Front speakers 6 x 12 cm (two)

 Factory preset adjustments for picture/sound

 Picture Shape: Letter box (HT27745 only), Zoom, Normal, and

Full (HT28745 only)

 Initial Channel (automatic selection)

 Receivable Formats: Digital Tuner for ATSC terrestrial broadcasts

and nonscrambled (ClearQAM) cable programs.

NTSC analog tuner for VHF/UHF or CATV

 Audio Format: Dolby

®

Digital for DTV and Analog for NTSC

 Channel Scan Memory

 Color Enhancer

 Auto Flesh Tone

 Receives 181 Analog Channels [VHF 2~13 and

UHF 14~69; Cable DTV 1, 14~125]; and

99 Digital Channels

 RF Antenna Input Jacks: Digital and Analog

 Component Video Input (Two Sets)

 Rear AV Input (Two Sets)

 S-Video Input (Two Sets)

 Optical Digital Audio Out

 Audio Out fixed

 Clock (auto clock)

 XDS (Extended Data Services) displays station call letters,

Title of show, and ratings when broadcast

 Sleep Timer (3 hours)

 32-Key Remote Control

FEATURES

SPECIFICATIONS

Picture Tube Size (Measured Diagonally):

HT27745- 27” True-Flat Screen Integrated HDTV

HT28745- 28” True-Flat Wide Screen Integrated HDTV

Scanning Format: 1080i [All Signals are Converted to 1080i]

RF Antenna Input: Analog–UHF/VHF/CATV 75 ohm

Digital–75 ohm

No Signal Reception: When tuned to an Analog Channel, and no

signal is present for more than 15 minutes, the DTV automatically

switches OFF. In Video Modes, DTV will NOT switch off automatically.

Power Requirement: Source: AC 120V, 60Hz

Power Consumption: 140 Watts (Average)

Sound: Two Speakers, size: 6 x 12cm

Amplifier: Built-in with 5.0W/ch

Jacks / Connectors:

Video 1 Input: S-Video1, Video and Audio L/R

Video 2 Input: S-Video2, Video and Audio L/R

Compo 2 Input: Component (Y/Pb/Pr), with

shared Video 2 Audio L/R Input

Compo 3 Input: Component (Y/Pb/Pr), and

Audio 3 L/R Input

Digital Audio Output: Dolby Digital (Optical)

Analog Audio Output: Audio L/R

Service Input Terminal: For Technical use only (Phone jack)

Size and Weight (approximately):

HT27745—27”

Horizontal Dim. (Width): 30.3 in. (770mm)

Vertical Dim. (Height): 23.0 in. (585mm)

Depth Dim. (Thickness): 19.5 in. (496mm)

Weight: 103.5 (lbs.), 47.0 (Kg)

HT28745—28”

Horizontal Dim. (Width): 33.8 in. (858mm)

Vertical Dim. (Height): 21.4 in. (543mm)

Depth Dim. (Thickness): 21.2 in. (537mm)

Weight: 92.3 (lbs.), 41.9 (Kg)

Specifications are subject to change without notice.

CAUTION: FCC Regulations state that improper modifications or un-

authorized changes to this unit may void the user’s authority

to operate the unit.

Trademarks Information:

Manufactured under license from Dolby Laboratories. Dolby and

the double-D symbol are trademarks of Dolby Laboratories

.

4

Need help?

Visit our Web site at www.sanyoctv.com or Call 1-800-877-5032

This symbol on the nameplate means the product is

Listed by Underwriters’ Laboratories Inc. It is

designed and manufactured to meet rigid U.L.

safety standards against risk of fire, casualty and

electrical hazards.

5

Need help?

Visit our Web site at www.sanyoctv.com or Call 1-800-877-5032

FIRST-THINGS-FIRST

This new high-definition digital television is capable of reproducing a crystal clear picture and exceptional

sound.

The signal makes the difference!

1

INITIAL SIGNAL CONNECTIONS

Analog RF Antenna Connection

•

Connect a Cable signal (with or without a cable

box), Satellite Receiver, or RF antenna to the

Analog RF input.

The analog tuner in this DTV receives Analog

Antenna signals, Analog Cable signals, or the RF

output from a Satellite Receiver, VCR, or cable box.

CATV FRANCHISE NOTE: Cable

companies, like public utilities,

are franchised by local govern-

ment authorities. To receive

cable programs, even with

equipment which is capable of

receiving cable channels, the

consumer must subscribe to

the cable company’s service.



DTV will select the correct Antenna mode for the type of Analog RF

signal connected automatically.



Use “Antenna Selection” in the Setup menu to change the Antenna

Mode.



DTV will switch off automatically after 15 minutes if there is no

signal reception (cable out or station not broadcasting).

Exception—When the Video mode is selected, the DTV will not auto-

matically switch off when signal reception has stopped for 15 minutes.



If you move the DTV to a new location, press the RESET key twice

after connecting the signal and turning on the DTV.

Analog Cable

RF

Antenna

Analog Satellite

Receiver

TV Back

VCR Back

NOTES: If you do not have a VCR connect signal directly

to DTV 75 (UHF/VHF/CATV) ohm terminal.

The only resolution available with any of these

connections, regardless of the original content, is

standard analog (SDTV).

Digital (DTV) Antenna Connection

•

Connect an RF antenna to the Digital Antenna In

terminal.

The digital tuner in this DTV receives HD signals

from an antenna. Digital signals from a STB are

received through a STB via the Component In jacks.

This DTV can receive and display ANY resolution

being broadcast (HDTV, EDTV, or SDTV).

RF

Antenna

DTV Back

TV Back

VCR Back

TV Back

VCR Back

(Continued on next page.)

OR

6

Need help?

Visit our Web site at www.sanyoctv.com or Call 1-800-877-5032

3

CHANNEL SEARCH

When the television is powered on

for the first time, it automatically

checks for the presence of an RF

signal.

•

Press the POWER key to turn

on the DTV.

•

Then press the CHANNEL

UP key to automatically

search for available channels:

Digital (ATSC) and Analog (NTSC).

The Channel Search contains two processes that are

executed simultaneously for digital and analog

channels.

NOTES:

The on-screen message for digital search will appear with a

progress bar and percentile number displayed across the

bottom of the screen (to indicate activity) as the search process

continues. (Channel numbers will appear under the progress

bar only when a digital channel is found.)

Channel information found during the channel search is

stored in the Channel Scan Memory database. After the

channel search is completed, the DTV will tune to the lowest

Digital channel or lowest Analog channel if no digital channels

are found.

If the DTV does not detect any

digital or analog channels, a

message advising the viewer

to check the cables and

antenna connections will

appear. In this case, you must

press the CHANNEL UP key

again to repeat the channel

search process. If after two

searches the DTV still fails to detect any channels, the DTV

will tune to analog channel 3. These two channel searches

are necessary even if you plan to use the DTV only as a

monitor.

If no analog or digital channels are found after the second

search, Channel Search will default to off-air analog channels

2 through 69 and digital channel D3-1. Select analog channels

using the remote control keypad. See page 11, item

number 3.

4

AUTO CLOCK SETTING (Optional)

After channel search is complete, the DTV will begin

Auto Clock setting. This feature searches for a local

PBS station that is broadcasting an extended data

service signal. This signal is used to automatically

set the clock/day. (This

may take several

seconds.) To cancel auto

clock setting, press the

CHANNEL UP key. (To

set the clock manually,

see page 19.)

5

ANTENNA SELECTION (Optional)

To change the initial ANALOG tuning system setup

(from antenna to cable or cable to antenna), use

the on-screen menu. See “Antenna Selection” on

page 15.

2

INSTALL TWO “AAA” BATTERIES

IMPORTANT NOTE: Spent or discharged batteries must be recycled

or disposed properly in compliance with all applicable laws. For

detailed information, contact your local County Solid Waste

Authority.

•

Install two “AAA” Batteries

(not included) so that the

“+” and “–” marks on the

batteries match the “+”

and “–” marks inside

the Remote.

To review the Remote

functions, go to

Pages 11 ~ 12.



Remove the batteries if the remote control will not be used for a

month or more. Weak batteries may leak and cause damage.

(Normal battery life is roughly six months.)



If batteries have leaked in the Remote Control Unit, carefully wipe

the case clean and load new batteries.

7

Need help?

Visit our Web site at www.sanyoctv.com or Call 1-800-877-5032

HDTV BACK—JACKS LOCATIONS AND FUNCTIONS

 Component Video Input (COMPO 2)—Connect

digital video equipment to the Y, Pb, Pr and Video 2

Audio L/R jacks. These jacks will automatically detect

the type of signal being received (HDTV, EDTV, or

SDTV). (See page 9.)

 S-Video (Video 1 and 2) Input—To enhance video

detail, use the S-Video (Video 1/2) jacks instead of the

Video jacks, if available on your external equipment.

(S-Video connections will override connections to the

Video 1/2 input jacks.) (See page 10.)

 Digital Audio Output—Use an Optical Audio cable to

connect the Digital Audio Output to an advanced

stereo home theater system equipped with Dolby

®

Digital 5.1. (See page 9.)

 Analog Audio Out (L/R) Jacks—Connect external

audio equipment here. (See page 10.)

 Component Video Input (COMPO 3)—Connect

digital video equipment to the Y, Pb, Pr and Audio 3

(L/R) jacks. These jacks will automatically detect the

type of signal being received (HDTV, EDTV, or SDTV).

(See page 9.)

 Audio/Video Input (VIDEO1/VIDEO2)—Connect

standard video equipment here. (See page 10.)

NOTE:

S-Video1/2 connections override the AV1/2

video composite connections.

 Analog Antenna Input (UHF/VHF/CATV)—Connect

an RF antenna, cable, or satellite receiver to this ter-

minal as shown on page 5.

 Digital Antenna Input—Connect an RF antenna to

this terminal as shown on page 5.

 Service Terminal—For technical use only.

 









Audio Cables—Provides analog left /right

audio for your external equipment connec-

tions.

Component:Y, Pb, Pr—Use these cables to

connect your component equipment. This

connection provides the best picture, but

does not include sound. (Cable colors:

Y = green, Pb = blue, and Pr = red.)

Composite Audio/Video (RCA type)—

Use these cables for standard analog

audio/video connections. Normally cables

are color coded: Yellow for Video, White for

(L) Audio, and Red for (R) Audio.

Coaxial Cable—Used to connect a signal to

your digital or Analog RF Antenna In terminal.

Optical Digital Audio—Use this cable to

connect the DTV ‘s digital audio output to a

multi-channel audio receiver.

S-Video Cable—This cable provide separate

luminance and color signals for higher reso-

lution and better picture quality. Use this

cable instead of the regular composite video

cable (RCA type), when available.

NOTE: None of these cables are supplied with this DTV.

GLOSSARY OF CABLES

8

Need help?

Visit our Web site at www.sanyoctv.com or Call 1-800-877-5032

CHOOSE YOUR CONNECTION

Digital Signal Compatible External Cables Needed Go to

Connections Equipment

(Not Supplied)

Page

9

This DTV is designed to handle several different connec-

tions making it compatible with Digital and Analog

devices.

In order to receive the best performance from your DTV,

choose your connection using this chart; then go to the

specified page for detailed instructions.

COMPONENT

(Y, Pb, Pr) IN

Will accept HDTV,

EDTV, or SDTV Video

content.

(Requires separate

audio connections.)

Component

Video

Cable

COMPOSITE VIDEO

OR

S-VIDEO IN

10

DIGITAL AUDIO

OUT

(Only available when

received as part of a

Digital RF signal.)

Optical

Digital

Cable

9

ANALOG AUDIO

OUT JACKS

10

Audio Cable

S-Video

Cable

Analog Signal Compatible External Cables Needed Go to

Connections Equipment

(Not Supplied)

Page

Composite

Video Cable

Satellite Receiver

Multi-Channel

Receiver

Satellite

Receiver

DVD Player

VCR

Stereo Amplifier

System

LEFT / RIGHT

ANALOG AUDIO IN

Audio Cable

Digital Cable Box

or DVD Player

9

Need help?

Visit our Web site at www.sanyoctv.com or Call 1-800-877-5032

USING COMPONENT JACKS TO

CONNECT A DVD PLAYER OR OTHER

DIGITAL EQUIPMENT

The Component Video jacks will accept HDTV, EDTV, or

SDTV video content.

Switch off DTV and external equipment before connect-

ing cables.

(Cables are not supplied.)

Follow these steps

to easily connect your STB or DVD to this DTV:

DVD Player

(or other digital

device such

as a Digital

Satellite

Receiver)

DTV Back

Component

Jacks

1

Connect DVD Player or other digital equipment’s

Component Video Out to the DTV’s Component

Video Input jacks.

2

Connect DVD Player or other digital equipment’s Audio

Out to the DTV’s Audio 3 Input jacks.

3

Press POWER to turn on the DTV, then turn on

external equipment.

4

Press the INPUT to select COMPONENT3 or

COMPONENT2 to view the DVD program.

What you will need

for connections:

Component Video Cable – 1

Audio Cable – 1

Remote Control

DIGITAL A/V CONNECTIONS



COMPO2 and COMPO3 jacks have identical functions. Compatible

video devices can be connected to either set of jacks.



Press the INPUT key after connecting the cables, to select the

COMPO2 or COMPO3 input signal. There is NO need to tune to a

blank channel.



“

No Signal” will appear randomly on the screen when no signal is

detected at the COMPO2 or COMPO3 inputs.



Position your DTV at least 2 feet from stereo speakers. The magnets

in the speakers may affect the picture quality.

2

4

3

CONNECTING DIGITAL AUDIO OUT

JACKS TO A MULTI-CHANNEL

RECEIVER

Dolby

®

Digital Audio provides 5.1 channels of surround

sound (five full-range channels [5] and one low-frequency

effect channel [.1]). A fiber optics cable is used to carry

the 5.1 surround sound (for low-noise signal transfer).

Back View

of DTV

Optical Digital

Cable

1

Using a Fiber Optics cable, connect the DTV’s Digital

Audio Output to the Digital Audio Input of a Multi-

Channel Receiver.

(Fiber optics cable is not supplied.)

2

Press POWER to turn on the DTV, then turn on exter-

nal equipment.

NOTES:

When making the connection, do not pinch or kink the fiber

optics cable.

Red light visible at the Digital Audio Output does not nec-

essarily indicate that Dolby 5.1 audio is available. Digital

audio is made up of light pulses that the human eye cannot

detect. Dolby 5.1 audio is available at the Digital Audio

Output only when received as part of a Digital antenna

signal.

What you will need

for connections:

Optical Cable – 1

Multi-Channel

Receiver

1

Remote Control

2

10

Need help?

Visit our Web site at www.sanyoctv.com or Call 1-800-877-5032

ANALOG A/V CONNECTIONS

USING THE ANALOG VIDEO JACKS

TO CONNECT A VCR (OR OTHER

ANALOG DEVICE)

Switch off DTV and external equipment before connect-

ing cables.

(Cables are not supplied.)

NOTE: Composite jacks

offer only 480i (SDTV)

resolution.

Back View of VCR

DTV AV

INPUT Jacks

1

Connect VCR’s Audio Video Out to the DTV’s Video In

jacks.

NOTE: For Mono VCR (Single Audio Jack), connect

VCR Audio Out to DTV Audio (L) Input.

22

Optional

Connect VCR’s S-Video Out to the DTV’s S-Video In

Jack.

NOTE: S-Video jacks connection override Video jacks

connection.

3

Press POWER to turn on the DTV, then turn on exter-

nal equipment.

4

Press the INPUT to select VIDEO 1 or VIDEO 2 to

view the VCR program.

What you will need

for connections:

Audio / Video Cable – 1

S-Video Cable – 1

S-Video

Jack

22

1

Remote Control

4

3

CONNECTING ANALOG AUDIO OUT

JACKS TO A STEREO AMPLIFIER

Switch off DTV and external equipment before connecting

cables.

(Cables are not supplied.)

Stereo Amplifier

Back View of DTV

What you will need for

connections:

Audio Cable – 1

1

Connect the DTV Audio Out (R/L) to the Stereo

Amplifier In (R/L).

2

Press POWER to turn on the DTV, then turn on

external equipment.

NOTES:

Do not connect external speakers directly to the DTV.

When TV Speaker is in the ON mode, sound will be

reproduced through your DTV and stereo amplifier.

When TV Speaker is in the OFF mode, sound will be

reproduced only through the stereo amplifier. (See page

20 to set DTV speakers.)

1



Press INPUT key after connecting cables to access the VIDEO 1 or

VIDEO 2 input. There is NO need to tune to a blank channel.



VIDEO 1 and VIDEO 2 jacks have identical functions. Any com-

patible analog video device can be connected to either set of jacks.



“No Signal” will appear randomly on the screen when no signal is

detected at the VIDEO 1 or VIDEO 2 inputs.



Position your DTV at least 2 feet from stereo speakers. The

magnets in the speakers may affect the picture quality.

Remote Control

2

11

Need help?

Visit our Web site at www.sanyoctv.com or Call 1-800-877-5032

USING THE REMOTE CONTROL

REMOTE CONTROL KEYS



Power Key—Press to turn DTV on or off.



Input Key—Press to change the input signal source

as follows: Analog RF  Digital RF  Video1  Video2

Compo2  Compo3  Analog RF.



Number Key—Two keys must be pressed to select a

direct channel.

Example:

Press 0 then 6 to select

channel 6. For Analog Cable channels above 100,

press and hold the 1 key until C1– – appears.



Info Key—Press to display the Digital and Analog Full

Banner information (press again to remove the

display):

Digital Full Banner display—Contains a two-part

Channel Number (Major and Minor). If available the

following is also included–Station ID, Program Title,

Date/Time (if set), Antenna Signal Strength, Video Res-

olution, V-Chip Program Rating, and Audio Reception.

Point towards

DTV

















PRECAUTIONS

To ensure safe operation, please observe the following precautions:

Replace both batteries at the same time. Do not use a new battery with

a used battery. Risk of explosion, if battery is replaced by an incorrect

type.

Do not expose the Remote Control Unit to moisture, or heat.

Virtual Channel

Major Minor

Station ID

Time/Date

Program

Title

Audio

Reception

V-Chip

Program

Rating

Video

Resolution

Signal

Strength

Analog Full Banner display—Contains Channel

Number (analog antenna/cable), Date / Time (if set),

Station ID (if available), Program Title (if available),

V-Chip Program Rating, and Audio Reception.

Station ID

Current Time/Date

Program Title

Audio

Reception

V-Chip Program

Rating

Channel No.



Recall Key—Select the first channel you want to

watch; then select another channel using the

NUMBER keys. Press RECALL to easily switch

between the channels.

NOTE: The RECALL key cannot toggle between a

Digital channel and an Analog channel. See TUNER

(#7) key description.



Menu key—Press this key to display the on-screen

menu.



Tuner Key—Use this key to toggle from one tuning

system to another, digital channels, and analog

channels.

NOTE: The TUNER key is inactive when an external

input is selected (Video 1, Video 2, Compo 2, or

Compo 3).



Cursor  (up)  (down) keys—Press these keys to

move the cursor up and down within the menu.

Cursor



(left)



(right) keys—Press these keys to

move the cursor left and right within the menu.

(Continued on page 12.)



12

Need help?

Visit our Web site at www.sanyoctv.com or Call 1-800-877-5032



Caption Key—Press to select analog or digital cap-

tioning. The Analog Caption modes are: CC1, CC2,

Quikcap, and OFF. The Digital Caption modes are:

Digital CC1 ~ CC6, Quikcap, and OFF.



Channel Scanning

((

CH ) Keys—Press  (up)

 (down) keys to tune to the next higher or lower

channel in the Channel Scan Memory database. The

scanning loop includes analog channels, digital chan-

nels, and all A/ V inputs.

Pix Shape Key—Use this key to change the video

display format. Available options depend on signal

received and the broadcast’s aspect ratio. They may

include: Letter box, Zoom, and Normal for HT27745;

Full, Zoom1/2, and Normal for HT28745.

Audio Key—Press to select the desired audio mode

(if available): DIGITAL: Main, Sub1, Sub2, Sub3, etc.;

ANALOG: Stereo, Mono, SAP.

Sleep Key—Press this key, then press the “0” key to

set the Sleep Timer. The desired time can be set from

30 minutes up to 3 hours in 30 minutes increments.

Sleep Timer will switch off the DTV automatically.

NOTE: The Sleep Timer cancels when the DTV is turned off

or if a power failure occurs.

Mute Key—Press once to minimize the volume. Press

again to restore.

NOTE: This key will not mute sound from the audio out

jacks

.

Enter Key—Press this key to select an option from

the menu system, when required.

Exit Key—Press this key to exit from the menu

system.

Volume (VOL – +) Keys—Press the

–– ++

keys to adjust

volume. The screen displays a left or right red arrow

that blinks as many time as you press the Vol

–– ++

keys.

Reset Key—Press twice to restore factory settings.

The DTV will automatically start Channel Search and

clear all customized settings.

NOTE: The Reset Function includes a channel search.

Current Digital and Analog channel databases will be

deleted and new ones created by the Channel Search

process. To receive Digital Cable channels, see page

14 for Digital Cable Search.

These features will reset to factory defaults:

• Picture/Sound Adjustments: Color, Tint,

Contrast, Brightness, Sharpness, Color Enhancer,

Bass, Treble, and Surround Sound

• Channel Memory —Digital/Analog channel

database will be replaced

• Initial Channel to OFF

• Analog Audio to Stereo

• Captioning to OFF

• V-Guide to OFF

• DTV Speakers to ON

• Digital Audio Output to Dolby Digital

• Scan Velocity to HIGH

• Menu Language to English

• Auto Clock / Sleep Timer (if previously set)

• Any Video mode to DTV mode

If desired, personal settings can be made again

using the menu options.

13

12

11

14

15

16

17

18

Model HT27745

Letter Box—Black

borders appear at

the top and bottom

of the screen.

Note: 16:9 image

without distortion

on a 4:3 screen.

Model HT28745

Normal—Black

borders appear at

the sides, of the

screen.

Note: 4:3 image

without distortion

on a 16:9 screen.

Zoom—Enlarges

image (some of the

top and bottom may

be clipped when

using Zoom 1 or

Zoom 2 modes).





11

12

13

14

16

15

18

17

REMOTE CONTROL KEYS (Continued)

13

Need help?

Visit our Web site at www.sanyoctv.com or Call 1-800-877-5032

DTV ADJUSTMENT AND SETUP

The on-screen menu system provides the viewer with

easy access to adjustments and settings. Just use the

MENU, CURSOR, ENTER, and EXIT keys on the

remote control and follow the on-screen instructions.

Generally, you will use the CURSOR  keys to

select a menu item and the CURSOR keys to

make an adjustment. The ENTER key confirms a

setting and moves the entry point to the next menu or

field, when necessary. Press the EXIT key to return to

normal DTV viewing.





IMPORTANT FACTS:

Some Menu options are specific to Digital

and Analog signals and will vary accordingly.

Also, some options are not available in com-

bination. Unavailable options will appear

“grayed-out” in the menu. For example, after

a Digital Cable Search, Digital Add-on Search

will be “grayed-out” because that option is

not supported for Digital Cable Channels.

(See Page 14.)

(See Page 17.)

(See Page 19.)

(See Page 18.)

(See Page 20.)

MENU NAVIGATION MAP

Sub Menus

HOW TO OPERATE THE ON-SCREEN MENU

14

Need help?

Visit our Web site at www.sanyoctv.com or Call 1-800-877-5032

IMPORTANT FACT: This DTV maintains only one database of

digital channels. Therefore, when you search for ClearQAM

digital cable channels, the database of antenna digital channels

will be deleted. You will only be able to receive those Clear-

QAM channels your cable company provides.

Cable companies rearrange virtual channels as programming

changes, which may cause the program you are watching to

move to another channel. This message will appear on the

screen briefly to notify you of a change. You will have to re-

locate the program you were watching by scanning through

the channels.

To restore the antenna digital channel database, reconnect the

antenna and use the menu system to perform a normal

Channel Search.

DIGITAL CABLE SEARCH (OPTIONAL)

This DTV can receive unscrambled (ClearQAM) digital

cable channels, when available. However, not all cable

companies provide ClearQAM digital channels.

Searching for digital cable channels will take about 10

minutes, please be patient.

1

Connect a Digital Cable signal directly to

the DTV Digital Antenna In Terminal.

2

Press the TUNER key to select the Digital Tuner.

3

Press the MENU key to display the Main menu.

4

Use the CURSOR  keys to highlight the

Channel

category. Press ENTER.

5

Use the CURSOR  keys to highlight

Digital

Cable Search

option. Press ENTER.

6

Use the CURSOR  key to select Yes. Press

ENTER.

NOTE: After Channel Search is complete, the DTV will

tune to the lowest Digital Cable channel (or lowest Analog

channel if no Digital Cable channel is found).

CHANNEL SETUP OPTIONS

CHANNEL SEARCH

1

Press the MENU key to display the Main menu.

2

Use the CURSOR  keys to highlight the

Channel

category

.

Press ENTER.

3

Use the CURSOR  keys to highlight the

Channel

Search

option. Press ENTER.

4

Use the CURSOR  key to select Yes. Press

ENTER.

Use Channel Search to replace existing Digital and Analog

Channel Scan databases, such as, if you move to another

city or have cable service installed.

NOTES:During Channel Search, current Digital and

Analog channel databases are deleted and new

ones created. To receive Digital Cable channels,

you will have to perform a Digital Cable Search.

To add new channels to existing databases, use

Digital Add-on Search on page 15.

15

Need help?

Visit our Web site at www.sanyoctv.com or Call 1-800-877-5032



ANTENNA SELECTION (ANALOG)

Use this feature to switch between analog off-air chan-

nels and analog cable channels.

1

Press the TUNER key to select analog channels.

2

Press MENU key to display the Main menu.

3

Use the CURSOR  keys to highlight the

Channel

category

.

Press ENTER.

4

Use the CURSOR  keys to highlight the

Antenna

Selection

option. Press ENTER.

5

Use the CURSOR  keys to choose Cable or

VHF/UHF. Press ENTER.

6

Press the EXIT key to return to normal DTV viewing.

DIGITAL ADD-ON SEARCH

Use this feature to add new channels to the digital

antenna channel database. Also, use this feature to add

channels when broadcast towers are in opposite direc-

tions from your location.

Channel numbers will appear under the progress bar only

when a channel is found.

1

Press the TUNER key to select the Digital Tuner.

2

Press MENU key to display the Main menu.

3

Use the CURSOR  keys to highlight the

Channel

category

.

Press ENTER.

4

Use the CURSOR  keys to highlight

Digital

Add-On Search

option. Press ENTER.

5

Use the CURSOR  key to select Yes. Press

ENTER.

NOTES: Turn your Antenna and repeat these steps for each

direction in which there are transmitting towers.

Go to www.antennaweb.org and type in your zip code

to obtain specific tower vector information.



16

Need help?

Visit our Web site at www.sanyoctv.com or Call 1-800-877-5032

CHANNEL SETUP OPTIONS (Continued)



When a digital channel is deleted, all of that channel’s sub-channels

are deleted as well.



Only previously deleted digital channels can be added back to the

database.



If one digital sub-channel is added back to the database all of that

channel’s sub-channels will be added back.



If the last remaining digital channel is deleted, the entire previous

Digital Channel Scan Memory database will be restored automatically.



If the last remaining analog channel is deleted (cable channel or off-

air channel) ALL analog channels (cable or off-air) will be restored

automatically, regardless of the previous Analog Channel Scan

Memory database.

INITIAL CHANNEL

The television can be programmed to tune to your

favorite channel each time it is powered on.

1

Press MENU key to display the Main menu.

2

Use the CURSOR  keys to highlight the

Channel

category. Press ENTER.

3

Use the CURSOR  keys to highlight the

Initial

Channel

option. Press ENTER.

4

Use the CURSOR  key to select On. Press

ENTER

.

5

Press the TUNER key to choose Digital or Analog.

6

Select your favorite channel using the CHANNEL

 keys on the remote.

7

Press the ENTER key to set the initial channel.

8

Press the EXIT key to return to normal DTV viewing.

1

Press MENU key to display the Main menu.

2

Use the CURSOR  keys to highlight the

Channel

category. Press ENTER.

3

Use the CURSOR  keys to highlight

Channel

Scan Memory

option. Press ENTER.

“Add?” will appear below the channel number if the

selected channel is not in the database. “Delete?” will

appear below the channel number if the selected channel

is already in the database.

4

Use the CHANNEL  keys or numerical keys to

select desired channel. HINT: Press the TUNER key

to switch between Digital and Analog Channel Scan

databases.

5

Press the ENTER key to delete or add the channel.

6

When you have finished adding and/or deleting chan-

nels, press the EXIT key to return to normal DTV

viewing.

CHANNEL SCAN MEMORY

Channel Scan Memory is a database of active channels

that you can scan through using the Channel Scan

(up/down) keys. This list can be customized by deleting

and/or adding channels.

NOTE: If the TV is powered off while any video mode is

selected, that video mode will be tuned when the TV

is powered on again (Video 1, Video 2, Component 2,

or Component 3).

17

Need help?

Visit our Web site at www.sanyoctv.com or Call 1-800-877-5032

CHANGING THE LOOK OF DIGITAL CAPTIONS

This

Size, Style, Color, Opacity

, and

Edge Style

of Digital Captions

can be changed.

NOTES: If Opacity is set to transparent, captions may be difficult to see.

Some menu screens include a “Sample Text” box display to

instantly view your selection.

Only true

EIA 708B Digital Closed-Captions are affected by all these

settings.

Analog captions generally will not respond to these adjustments,

however, upconverted analog captions may respond to some options.

1

Press the TUNER key to select the Digital Tuner.

(

NOTE: Digital Font options are available only from the Digital

Main menu.

)

2

Press the MENU key to display the Main menu.

3

Use the CURSOR  keys to highlight the

Digital Caption

category. Press ENTER.

4

Use the CURSOR  keys to highlight an option. Press

ENTER.

5

Some choices have

Background

and

Foreground

options.

Choose

Background

or

Foreground

when necessary, then use

the CURSOR  or keys to select the desired effect.

Otherwise, simply use the CURSOR  or keys to

select the desired effect.

6

Press the MENU key to move back to the Digital Caption

menu, then repeat Steps 4 and 5 for each option you want to

change.

7

When you have finished making adjustments, press the EXIT

key to return to normal DTV viewing.

TO VIEW CAPTIONS

1

Press the CAPTION key to select caption modes. Digital

modes are: Digital CC1 through Digital CC6, QuikCap, and Off.

Analog modes are: CC1, CC2, QuikCap and Off.

QuikCap Operation

QuikCap turns captioning on and off with the

Mute

function. Press

the MUTE key on the remote control to block the TV sound; the cap-

tions display automatically. Press the MUTE key again to restore the

sound. Captions will disappear.









CLOSED-CAPTIONING OPTION

Analog Caption

Digital Caption

Captioning is hidden textual information transmitted

along with the picture and sound. Turning Captioning

ON causes the DTV to open these captions and

superimpose them on the screen. Because different

types of closed captions can be transmitted with the

picture and sound, separate captioning modes are

provided. The captioning modes recognized by this

model are: Analog EIA-608B and Digital EIA-708B.

Local broadcasters decide which caption signals to

transmit.



Main Menu—Digital Font

Sub Menu—Digital Font Size

18

Need help?

Visit our Web site at www.sanyoctv.com or Call 1-800-877-5032

TO TEMPORARILY UNBLOCK MOVIE

OR TV PROGRAM

1

Press the INFO key, then within three

(3) seconds press the ENTER key.

This will temporarily sets the V-Guide to

OFF. The V-Guide will remain in the OFF

mode until the DTV power is switched off.

When power is restored, V-Guide will be

ON.

Also, V-Guide can be reset to ON by using

the menu system above, steps 1~3.

TO UNBLOCK MOVIE OR TV PROGRAM

1

Press the MENU key to display the Main menu.

2

Use the CURSOR  keys to highlight the

V-Guide

category. Press ENTER.

3

Highlight the “ALLOW ALL” option using the

CURSOR , keys, if needed. Press ENTER.





V-GUIDE (PARENTAL CONTROL) OPTION

NOTE: THIS FEATURE IS DESIGNED TO COMPLY WITH THE

UNITED STATES OF AMERICA’S FCC V-CHIP REGULATIONS.

THEREFORE, IT MAY NOT FUNCTION WITH BROADCASTS

THAT ORIGINATE IN OTHER COUNTRIES.

This Sanyo television is equipped with an electronic

V-Chip to interpret MPAA (Motion Picture Association of

America) and TV Parental Guidelines rating codes. When

these codes are detected, the DTV will automatically

display or block the program, depending upon choices

you make when setting up the V-Guide system. Content

ratings are represented by the initials: FV (fantasy vio-

lence), D (suggestive dialog), L (adult language), S (sexual

situations), and V (violence). A rating icon will generally

appear at the beginning of a program, see chart on

page 19.

This television can be set to block programs with

content you deem as inappropriate for your children to

view.

TO BLOCK MOVIE OR TV PROGRAM

1

Press the MENU key to display the Main menu.

2

Use the CURSOR  keys to highlight the

V-Guide

category

.

Press ENTER.

3

Use the CURSOR  keys to select ON. Press

ENTER.

4

Use the CURSOR  to select

Adjust

. Press ENTER.

5

Press CURSOR  and keys to select Movie

or TV ratings.

6

Press the ENTER key to Block selected option.

A lock symbol ( ) will appear beside the selected

rating option indicating it is blocked.

7

When you have finished making adjustments, press

the EXIT key to return to normal TV viewing.





V-GUIDE RATINGS—AT-A-GLANCE

MOVIE RATING

TV RATING

LOCKED

SYMBOL

RATED

GUIDELINES

(Dark Gray)

UNRATED

GUIDELINES

(Light Gray)

IMPORTANT FACT: The DTV will automatically

block ratings above or unblock ratings below a

selection. For example, if you block TV rating

TV-PG, ratings TV-14 and TV-MA will be

blocked automatically; or if you block Movie

rating PG-13, ratings R, NC17, and X will be

blocked automatically.

Blocking TVY7 does not block higher ratings.

19

Need help?

Visit our Web site at www.sanyoctv.com or Call 1-800-877-5032

(Continued on page 20.)

SETUP MENU OPTION

Manual Date/Time Setting

4

Use the CURSOR  keys to highlight

Manual

Setup

. Press ENTER.

5

Use the CURSOR  keys to select the

Hour

. Press

the ENTER key (CURSOR keys) to step to the

next field. Continue until all fields are populated.

NOTE: The DTV will ignore all entries if the MENU or EXIT

key is pressed before all fields are populated.

6

When you have entered data in all of the fields, press

the EXIT key to return to normal DTV viewing.





SETTING DATE/TIME

Auto Date/Time Setting

1

Press the MENU key to display the Main menu.

2

Use the CURSOR  keys to highlight the

Setup

category

. Press ENTER.

3

Use the CURSOR  keys to highlight the

Date / Time

option. Press ENTER.

4

Use the CURSOR  keys to highlight

Auto Clock

.

Press ENTER.

The TV will begin searching

for an analog PBS channel

transmitting date and time

data. If a PBS station is

found transmitting this data,

it will be used to set the

Date and Time automati-

cally. When the process is

completed (or cancelled),

the last analog channel will

be tuned.

NOTE: If the Date and Time are set automatically, the

Date and Time will be updated each time that PBS station

is tuned.



The V-Guide menu display remains on screen for approximately 30

seconds. If it disappears, press the V-GUIDE key.



You can block portions of a TV rating by choosing one or more of

the Content ratings (D, L, S, and V). By blocking just the L and S

content ratings of TV-14,

for example,

TV-14 rated programs with a

D and/or V content rating could still be viewed.



V-Guide limits on programming received via the Analog antenna

input, Digital antenna input, A/V 1 input, and any 480i signals

received through the component jacks are controlled by this DTV.



V-Guide limits on digital programming received through the Compo-

nent jacks are controlled by the external devices connected to those

jacks (such as a DVD Player or Satellite Receiver). Refer to your

external device’s owner’s manual for instructions on setting V-Guide

limits.



Networks and local stations may or may not include the content

ratings portion of the TV Parental Guidelines.

ALL CHILDREN—Program is designed to be appropriate for

children ages 2-6.

DIRECTED TO OLDER CHILDREN—Program is designed for

children 7 and above. Material may include mild fantasy

violence (FV) or comedic violence.

GENERAL AUDIENCE—Program suitable for all ages. Contain

little or no violence, no strong language or sexual dialogue or

situations.

PARENTAL GUIDANCE SUGGESTED—Program contains

material that may be unsuitable for younger children. Mater-

ial contains one or more for the following: moderate violence

(V), some sexual situations (S), infrequent coarse language

(L), or some suggestive dialogue (D).

PARENTS STRONGLY CAUTIONED—Some material is

unsuitable for children under 14 years of age. Parents are

strongly urged to use cautions against letting children that 14

watch unattended. Material contains intense violence (V),

intense sexual situations (S), strong coarse language (L), or

intensely suggestive dialogue (D).

MATURE AUDIENCE ONLY—Program is designed to be

viewed by adults and therefore may be unsuitable for children

under 17 years of age.

TV RATINGS (AGE/CONTENT-BASED)

G GENERAL AUDIENCES—All ages admitted.

PG PARENTAL GUIDANCE SUGGESTED—Some material may not

be suitable for children.

PG-13 PARENTAL GUIDANCE CAUTIONED—Some material may be

inappropriate for children under 13.

R RESTRICTED—Under 17 requires accompanying parent or

adult guardian

NC17 NO ONE 17 AND UNDER ADMITTED

MPAA MOVIE RATINGS (AGE-BASED)



20

Need help?

Visit our Web site at www.sanyoctv.com or Call 1-800-877-5032

MENU LANGUAGE

1

Press the MENU key to display the Main menu.

2

Use the CURSOR  keys to highlight the

Setup

category. Press ENTER.

3

Use the CURSOR  keys to highlight

Menu

Language

option. Press ENTER.

4

Use the CURSOR  keys to select

English

,

Español, or Français.

5

Press the EXIT key to return to normal DTV viewing.

PICTURE/SOUND ADJUSTMENT

OPTIONS

PRESET PICTURE AND SOUND OPTIONS

Select

Sports

,

Movie

, or

News

to match the program you

are watching. The DTV will adjust the picture and sound

accordingly.

A yellow bullet will display beside the selected option.

1

Press the MENU key to display the Main menu.

2

Use the CURSOR  keys to highlight the

Picture / Sound

category. Press ENTER.

3

Use the CURSOR  keys to choose either

Movie,

Sports,

or

News

.

4

Press the EXIT key to return to normal DTV viewing.

DIGITAL AUDIO OUTPUT

Use this feature to choose the format of the audio

output signal: Dolby Digital or PCM.

1

Press the MENU key to display the Main menu.

2

Use the CURSOR  keys to highlight the

Setup

category. Press ENTER.

3

Use the CURSOR  keys to highlight the

Digital

Audio

option. Press ENTER.

4

Use the CURSOR  keys to select Dolby Digital or

PCM.

5

Press the EXIT key to return to normal DTV viewing.

NOTE: The Digital Audio Output option is available

only when you are watching a Digital channel

received via the Digital antenna input. If you are

watching a signal from any Analog input (Analog

tuner or Analog A / V inputs), the Digital Audio

Output option will be “grayed-out” (unavailable).

TV SPEAKER

1

Press the MENU key to display the Main menu.

2

Use the CURSOR  keys to highlight the

Setup

category. Press ENTER.

3

Use the CURSOR  keys to highlight

TV Speaker

option. Press ENTER.

4

Use the CURSOR  keys to select ON.

5

Press the EXIT key to return to normal DTV viewing.

NOTE: Sound will not be produced

through your DTV speakers when the

OFF mode is selected.

SETUP MENU OPTION (Continued)

La page est en cours de chargement...

Sanyo HT28745 Le manuel du propriétaire

Ce manuel convient également à

Sanyo HT28745 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents