Blue Rhino Electric Heater 91000 Manuel utilisateur

Marque: Blue Rhino

Modèle: Electric Heater 91000

Taper: Manuel utilisateur

Ce manuel convient également à

91000

Owner’s Manual

Manuel d’utilisation

Model No.

91000

WARNING

FOR YOUR SAFETY:

Improper installation,

adjustment, alteration,

service or maintenance

can cause injury or property

damage. Read the installation,

operation and maintenance

instructions thoroughly before

installing or servicing this

equipment.

AVERTISSEMENT

POUR VOTRE SECURITE:

Tout mauvais réglage ainsi que

toute installation, modification,

ou maintenance incorrecte

risque de provoquer des

blessures ou des dégâts

matériels. Lire complètement les

instructions concernant l’instal-

lation, le fonctionnement et

l’entretien avant d’installer ou

de procéder à la maintenance de

cet appareil.

AVERTISSEMENT

POUR VOTRE SÉCURITÉ

À utiliser uniquement à

l’extérieur

(hors de tout espace clos)

WARNING

FOR YOUR SAFETY:

For Outdoor Use Only

(outside any enclosure)

Owner’s manual and assembly instructions: 91000 portable outdoor heater 7/02

Contact 1-800-762-1142 for assistance.

Do not return to place of purchase.

Table of Contents

Safety First! . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Assembly Instructions

Hardware & Component Listing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

General Components & Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Additional Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Step 1 Attach Emitter Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Step 2 Attach Top Wire Guard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Step 3 Attach Dome to Emitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Step 4 Attach Dome Cap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Step 5 Gas Hook-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Step 6 Check for Leaks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Step 7 Install Access Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Step 8 Securing the tank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Operation

Before Turning Gas Supply ON . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Before Lighting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Lighting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Re-Lighting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Operation Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

THE INSTALLATION OF THIS UNIT MUST CONFORM WITH LOCAL

CODES, OR IN THE ABSENCE OF LOCAL CODES, THE NATIONAL

FUEL GAS CODE, ANSIZ223.1-1988 (CAN1-B149 INSTALLATION

CODE).

Save these instructions for future reference.

If you are assembling this unit for someone else, give

this manual to him or her to save for future reference.

WARNING

FOR YOUR SAFETY:

If you smell gas -

1. Shut off gas to appliance.

2. Extinguish any open flame.

3. If odor continues, contact

your gas supplier or local

fire department.

WARNING

California Proposition 65:

Chemicals Known To The

State Of California To Cause

Cancer, Birth Defects, Or

Other Reproductive Harm Are

Created By The Combustion

Of Propane.

WARNING

FOR YOUR SAFETY:

Do not store or use gasoline

or other flammable vapors or

liquids in the vicinity of this

or any other appliance.

WARNING

FOR YOUR SAFETY:

1. Gas leaks may cause a fire

or explosion which can

cause serious bodily injury

or death, or damage to

property.

2. You must follow all leak-

checking procedures as

outlined in step 6 before

operating this unit.

3. Never use an open flame to

check for leaks.

Owner’s manual and assembly instructions: 91000 portable outdoor heater 7/02

Contact 1-800-762-1142 for assistance.

Do not return to place of purchase.

Safety First!

Read and become familiar with this entire manual, especially the following

precautions. If you are unsure of anything in these instructions or the

operation of your heater, STOP and contact 1-800-762-1142 for assistance.

Caution: This appliance is for outdoor use only (outside any enclosure).

Always make sure there is fresh air ventilation.

• Always maintain at least 36” clearance from combustible materials.

• Always place heater on a hard and level surface.

• Do not use if the wind velocity is greater than 10 miles per hour.

• Heater operates at reduced efficiency below 40ºF (5ºC).

• Keep sprinklers and other water sources away from burner and controls.

• When using the gas extension hose always locate the hose out of

pathways where people may trip over it or in areas where the hose may

be subject to accidental damage.

• Always use extreme caution when near heater. Alert both children

and adults to the hazards of high temperatures, especially to avoid

burns or clothing catching fire.

• Young children and pets should be carefully supervised when they

are in the area of heater.

• Do not hang clothing or other flammable materials either on or

near heater.

• Any guard or other protective device removed for servicing the

heater must be replaced prior to operating the heater.

• Certain materials or items, when stored under heater, will be subjected to

radiant heat and could be seriously damaged.

• Do not modify heater in any manner.

• The pressure regulator and hose assembly supplied with the appliance

must be used and replacements must be those specified by the

manufacturer.

• Inspect heater and extension hose before each use of the appliance. If a

damaged part is detected, do not operate until an original equipment

replacement part has been properly installed. Use of unauthorized parts

will void warranty and create an unsafe condition.

• Do not attempt to use this appliance without a functional factory-supplied

gas regulator in place. If regulator becomes damaged, use only a factory-

supplied replacement.

• During operation, do not touch burner assembly. The surface of heater’s

emitter can reach temperatures approaching 1600ºF.

• After shutdown, do not touch emitter assembly until heater has cooled

(approximately 45 minutes after use).

Notice: This product should not be used with any fuel other than liquid

propane. Use of other fuels will detract from heaters performance and will

void your warranty.

WARNINGS

FOR YOUR SAFETY:

• Purchaser assumes all risk in

the assembly and operation of

this unit. Failure to follow this

manual’s warnings and

instructions can result in

severe personal injury, death

or property damage.

• Combustion of propane creates

carbon monoxide, which,

when used in enclosed

areas, can kill you.

• Dome is extremely hot to the

touch during operation. Never

touch the dome while the heater

is operating. Wait for unit to

cool down (approximately 45

minutes) after use.

• Do not use in an explosive

atmosphere. Keep heater away

from areas where flammable

liquids, gasoline, vapors, or

explosives are stored or used.

Before you do anything else,

read and understand all

precautions in Safety First!

Contact 1-800-762-1142 for assistance.

Do not return to place of purchase.

Dome

Dome Cap

Top Wire Guard

Emitter Assembly

Bottom Wire Guard

Post

Shroud Cover

Housing

Access Panel

Base

Components

Used In

Picture Qty Description Step

4 Medium Screw 1

3 Nut 3

1 Finial 4

1 Dome Cap 4

1 Extension Hose 5

Hardware

Extension Hose

Owner’s manual and assembly instructions: 91000 portable outdoor heater 7/02

Finial

Owner’s manual and assembly instructions: 91000 portable outdoor heater 7/02

Contact 1-800-762-1142 for assistance.

Do not return to place of purchase.

Assembly Instructions

General Components & Features

Familiarize yourself with all components before proceeding. Refer to page 4 for all hardware components.

Do NOT attempt assembly unless all components are available. If you believe a component is missing or damaged,

contact 1-800-762-1142 for assistance.

Additional Requirements

The following items are not included, but are necessary for the proper assembly of your heater. Do NOT attempt to

assemble without proper tools.

(1) - 7/16” Wrench

(1) - #2 Phillips Head Screwdriver

(1) - Leak Detection Solution (Instructions on how to make solution are included in Step 6)

(1) - 20 lb.(4-5 gallon) precision filled LP Gas Grill Cylinder

Note: You must follow all steps to properly assemble heater.

Step 1 – Attach Emitter Screen

• Line up 4 holes on bottom of Emitter Screen with corresponding holes

in Emitter Bottom, and insert (4) Medium Screws in holes until tight.

Owner’s manual and assembly instructions: 91000 portable outdoor heater 7/02

Contact 1-800-762-1142 for assistance.

Do not return to place of purchase.

Step 2–Attach Top Wire Guard

• Line up 4 prongs on Wire Guard Bottom with 4 holes on Emitter

Bottom, and Insert.

Note: It may be necessary to adjust the prongs slightly to line them up

with the holes.

Step 3–Attach Dome to Emitter

• Line up three studs in Emitter with holes in Dome. Slide Dome

carefully over studs, clamping Top Wire Guard securely in place.

Note: It may be necessary to adjust prongs of the Top Wire Guard

slightly to provide a secure fit.

• Install (3) Nuts on studs and tighten with 7/16” wrench.

Do not over tighten.

Owner’s manual and assembly instructions: 91000 portable outdoor heater 7/02

Contact 1-800-762-1142 for assistance.

Do not return to place of purchase.

Step 5 – Gas Hook-up

Note: For best results, use heater with a 20 lb. cylinder.

The pressure regulator and hose assembly supplied with the appliance

must be used and replacements must be those specified by the

manufacturer.

To connect 20 lb. Cylinder

• Slip end of flexible gas line with brass fitting through center hole of

Base and up to threaded portion of regulator.

• Line up threads on fitting with those on regulator and rotate clockwise

until snug. HAND TIGHTEN ONLY. DO NOT USE ANY HAND

TOOLS TO MAKE THIS CONNECTION. BE CAREFUL NOT TO

CROSS THREADS WHEN SCREWING IN FITTING.

• Set heater on base, making sure that flexible gas line is routed

through small slot in base.

• Attach gas line to cylinder by turning black plastic knob counter

clockwise into cylinder valve until tight.

Note: Be careful not to kink flexible gas line.

To connect 14.1 oz or 16.4 oz cylinder

Note: Some 1-lb cylinders may form frost when near empty.

• Rotate regulator to point towards opening in shroud.

• Line up threads on canister with those on regulator, insert and rotate

canister clockwise until they fit snugly together. HAND TIGHTEN

ONLY. BE CAREFUL NOT TO CROSS THREADS WHEN

SCREWING IN CANISTER.

Step 6 – Check for Leaks

To check for leaks:

• Make 1-2 oz. of leak solution by mixing one part liquid dishwashing

soap and 3 parts water.

• Spoon several drops (or use squirt bottle) of the solution onto the

regulator/canister connections.

• Inspect the connections and look for bubbles

• If NO bubbles appear, the connection is safe.

• If bubbles appear, there is a leak:

• Loosen and re-tighten this connection.

• Re-check for a leak.

• If you continue to see bubbles after several attempts, disconnect

propane source and contact 1-800-762-1142.

Caution:

Your Endless Summer Portable Heater

has been checked at all factory

connections for leaks. Recheck all

connections, as movement in shipping

can loosen connections. Check for

leaks even if your unit was assembled

for you at the store.

Caution:

Before you attempt to use a propane

cylinder, understand all cylinder and

propane related precautions in Section

#1 – “Safety First.”

Owner’s manual and assembly instructions: 91000 portable outdoor heater 7/02

Contact 1-800-762-1142 for assistance.

Do not return to place of purchase.

Step 7 – Install Access Panel

• Rotate door up to closed position and tighten thumb screw

Step 8 – Securing the Tank

Mount your 20 lb. cylinder to a sturdy object such as a table or post

within 3 to 4 feet of your heater when in use, this will prevent movement

or tipping of the cylinder during operation.

The clamp on the cylinder ring will attach to any round pole from 1” to

2” in diameter, or a square post from 1” to 2” square. It will also adapt to

various other shapes up to 2” wide.

Determine where to locate your 20 lb. cylinder. Be sure that it is within

2” what you are mounting it to.

Place the bracket halves around the object and insert the 2” bolts

through the open holes in one bracket and into the matching threaded

holes in the second bracket. Position bracket within 6” of the middle of

the cylinder. Finger tighten bolts.

Slide the 20 lb. cylinder into the curved portion of the bracket, making

sure strapping ends are not between cylinder and bracket. Enclose

cylinder in strap and securely tighten strap in buckle.

Using a 7/16” wrench, tighten the 2” bolts until they are secure. DO

NOT OVER TIGHTEN.

In some cases you may wish to secure your cylinder to a larger object

or a wall. It is possible to mount the bracket attached to the straps to

these surfaces by drilling matching holes and using screws and nuts or

lag screws (not provided) to secure your cylinder.

Note: Once you have read “safety first” and successfully completed

Steps 1 – 8, you are ready to begin operating your heater.

Owner’s manual and assembly instructions: 91000 portable outdoor heater 7/02

Contact 1-800-762-1142 for assistance.

Do not return to place of purchase.

Operation

Before Turning Gas Supply ON

Your heater was designed and approved for OUTDOOR USE ONLY.

DO NOT use it inside a building, garage, or any other enclosed area.

Make sure surrounding areas are free of combustible materials,

gasoline, and other flammable vapors or liquids.

Ensure that there is no obstruction to air ventilation.

Be sure all

gas connections are tight and there are no leaks (see step 5).

Be sure the access panel is clear of debris.

Be sure any component removed during assembly or servicing is

replaced and fastened prior to starting.

Before Lighting

Heater should be thoroughly inspected before each use, and by a

qualified service person at least annually.

If relighting a hot heater, always wait at least 5 minutes for gas to

dissipate.

Lighting

1. Turn Gas Control Knob to OFF position.

2. Push in Control Knob and rotate to “ON” position. This will light

burner. If necessary, keep depressing and rotating Knob until burner

lights.

3. Once burner is lit, hold Control Knob in for at least 30 seconds and

release.

4. If burner does not stay lit, wait 5 minutes and repeat steps 2 and 3.

5. Once burner is lit, rotate Knob to desired heating level.

6. Replace Access Panel.

If you experience any ignition problem, turn off the heater and gas

supply, and consult “Troubleshooting” on page 12.

WARNINGS

FOR YOUR SAFETY:

• Do NOT attempt to operate

heater until you have read

and understand all

precautions in section 1

“Safety First.” Failure to do

so can result in serious

personal injury, death, or

property damage.

• If at any time you are unable

to light burner and smell gas,

wait 5 minutes to allow gas

to dissipate before

attempting to light heater.

• Do NOT touch emitter or

dome or move heater for at

least 45 minutes after use.

OFF

HIGH

LOW

OFF

HIGH

LOW

Owner’s manual and assembly instructions: 91000 portable outdoor heater 7/02

Contact 1-800-762-1142 for assistance.

Do not return to place of purchase.

Caution: Avoid inhaling fumes emitted from the heater’s first use.

Smoke and odor from the burning of oils used in manufacturing

will appear. Both smoke and odor will dissipate after

approximately 30 minutes. The heater should NOT produce thick

black smoke.

Note: The burner may be noisy when initially turned on. To eliminate

excessive noise from the burner, turn the Control Knob to the LOW

position. Then, turn the knob to the level of heat desired.

When heater is ON:

Emitter screen will become bright red due to intense heat. The color is

more visible at night.

Burner will display tongues of blue flame. These flames should not

be yellow or produce thick black smoke, indicating an obstruction of

airflow through the burners.

If yellow flame is detected, turn off heater and gas supply and consult

“Troubleshooting” on page 12.

Re-lighting

Note: For your safety, Control Knob cannot be turned ON without first

depressing Control Knob in OFF position and then rotating to ON.

1. Turn Gas Control Knob to OFF.

2. Wait at least 5 minutes to let gas dissipate before attempting to

relight burner.

3. Repeat the “Lighting” Steps 2 and 3 on prior page.

Shut Down

1. Rotate Gas Control Knob to OFF position. Normally, burner will

make a slight popping sound when extinguished.

2. Turn off gas at cylinder.

3. Remove Access Panel.

4. Unscrew gas line from regulator.

5. Close Access Panel.

Note: After use, some discoloration of the emitter screen is normal.

WARNING

FOR YOUR SAFETY:

Be careful when attempting to

manually ignite this heater.

Holding in the contrrol know for

more than 10 seconds before

igniting the gas will cause a ball

of flame upon ignition.

Owner’s manual and assembly instructions: 91000 portable outdoor heater 7/02

Contact 1-800-762-1142 for assistance.

Do not return to place of purchase.

Operation Checklist

For a safe and pleasurable heating experience, perform this check before

each use.

Before Operating

 I am familiar with entire owner’s manual and understand all precautions

noted in “Safety First.”

 All components are properly assembled, intact and operable.

 No alterations have been made.

 All gas connections are secure and do not leak.

 Wind velocity is below 10 mph.

 Outdoor temperature is greater than 40 degrees F.

 Heater is outdoors (outside any enclosure).

 There is adequate fresh air ventilation.

 Heater is away from gasoline or other flammable liquids or vapors.

 Heater is away from windows, air intake openings, sprinklers and other

water sources.

 Heater is at least 36” from combustible materials.

 Heater is on a hard and level surface.

 There are no signs of spider or insect nests.

 All burner passages are clear.

 All air circulation passages are clear.

 Children, pets, clothing, flammable materials and items that can be

damaged from radiant heat are away from the heater.

 Children and adults in the area have been alerted to the high

temperature hazards: especially burns and clothing fires.

 Children and adults in the area have been warned not to touch heater

near engine during operation and until unit has cooled.

After Operation

 Gas control is in OFF position.

 Gas tank valve is OFF

 Disconnect Gas line.

 Heater is upright in a secure location.

Owner’s manual and assembly instructions: 91000 portable outdoor heater 7/02

Contact 1-800-762-1142 for assistance.

Do not return to place of purchase.

Troubleshooting

If the problem is:

And this condition exists: Then do this

Burner won’t light Gas pressure is low

Blockage in burner openings

Blockage in venturi tube

Blockage in gas line

Control knob is not in ON position

Replace cylinder or canister

Clear blockage

Clean venturi

Check gas line for blockage

Turn control knob to ON

Burner won’t stay lit Bad thermocouple

Corrosion at thermocouple

Burner flame not touching

thermocouple

Replace thermocouple

Clean contact

Contact certified technican

Burner flame is low

Note: Heater operates at reduced

efficiency below 40ºF (5ºC)

Gas pressure is low

Outdoor temperature is less than

40ºF and tank is less than 1/4 full

Control knob fully ON

Turn Control Knob OFF and replace

cylinder or canister

Use a full cylinder or canister

Check burner and all openings for blockage

Emitter glows unevenly Gas pressure is low

Heater not level

Burner tilted

Replace cylinder or canister

Level heater

Straighten burner

Carbon build-up Base is not on a level surface

Heater is level

Dirt or film on reflector and emitter

Place heater on a level surface

Clean burner

Clean reflector and emitter

Thick black smoke Blockage in burner Remove blockage and clean burner inside

and outside

Owner’s manual and assembly instructions: 91000 portable outdoor heater 7/02

Contact 1-800-762-1142 for assistance.

Do not return to place of purchase.

Maintenance

To enjoy years of outstanding performance from your heater make sure you

perform the following maintenance activities on a regular basis:

• Keep exterior surfaces clean.

• Use warm soapy water for cleaning. Never use flammable or corrosive

cleaning agents.

• While cleaning your unit, be sure to keep the area around the burner

and pilot assembly dry at all times. Do not submerge the control valve

assembly. If the gas control is submerged in water, do NOT use it.

It must be replaced.

Air flow must be unobstructed. Keep controls, burner, and circulating air

passageways clean. Signs of possible blockage include:

• Gas odor with extreme yellow tipping of flame

• Heater does NOT reach the desired temperature.

• Heater glow is excessively uneven.

• Heater makes popping noises.

Spiders and insects can nest in burner or orifices. This dangerous condition

can damage heater and render it unsafe for use. Clean burner holes by

using a heavy-duty pipe cleaner. Compressed air may help clear away

smaller particles.

Carbon deposits may create a fire hazard. Clean dome and emitter with

warm soapy water if any carbon deposits develop.

Note: In a salt-air environment (such as near an ocean) corrosion occurs

more quickly than normal. Frequently check for corroded areas and repair

them promptly.

TIP:

Use high-quality automobile wax to help maintain the appearance of your

heater. Apply to exterior surfaces from the pole down. Do not apply to

emitter screen, dome, or wire guard.

Owner’s manual and assembly instructions: 91000 portable outdoor heater 7/02

Contact 1-800-762-1142 for assistance.

Do not return to place of purchase.

Storage

Between uses:

Turn Control Knob OFF.

Disconnect LP source.

Note: When appliance is not in use cylinder must be disconnected.

The LP-gas supply cylinder must be disconnected when this appliance is

not in use.

Store heater upright in an area sheltered from direct contact with

inclement weather (such as rain, sleet, hail, snow, dust and debris).

If desired, cover heater to protect exterior surfaces.

Note: Wait until heater is cool before covering.

During periods of extended inactivity or when transporting:

Turn Control Knob OFF.

Disconnect LP source and move to a secure, well-ventilated location

outdoors.

Store heater upright in an area sheltered from direct contact with

inclement weather (such as rain, sleet, hail, snow, dust and debris).

If desired, cover heater to protect exterior surfaces.

Note: Wait until heater is cool before covering.

Never leave LP cannister exposed to direct sunlight or excessive heat.

Service

To learn how to service and procure parts for worn out, defective or damaged

components contact 1-800-762-1142 for assistance or e-mail

[email protected]. Please supply model number and serial ID

number for best service support. These numbers can be found on the

heater’s rating plate, located on the housing.

Caution: The pressure regulator and hose assembly supplied with

the appliance must be used and replacements must be those specified

by the manufacturer. Use only original equipment replacement parts.

Use of unauthorized parts or modification of parts will void warranty

and create an unsafe condition.

Caution: Always allow heater to cool before attempting service.

FOR YOUR SAFETY:

Never attempt to refill disposable

canister. Refilling may cause

explosion. To discard, contact

local refuse hauler or recycle

center.

Do not puncture or incinerate.

Owner’s manual and assembly instructions: 91000 portable outdoor heater 7/02

Contact 1-800-762-1142 for assistance.

Do not return to place of purchase.

Warranty

Warranty Period

Heater’s warranty extends for 1 years from date of purchase by original purchaser.

Warranty Terms

Manufactured by UniFlame Corp. 1817 Kenosha Road. Zion, Illinois 60099. 1-800-762-1142.

Manufacturer will cover: All parts found to be defective due to materials or workmanship for 1 years from the date of original purchase.

Proof of purchase is required before warranty performance will be rendered. Sales receipt and validation of product registration are

valid forms of proof of purchase.

Manufacturer will repair or replace parts returned prepaid freight in the U.S.A. at its sole discretion.

There are no other express or implied warranties.

arranty Exclusion

Manufacturer will NOT cover:

Assembly or start-up

Normal adjustment to burner

Cleaning and/or general maintenance

Shipping damage

Any misuse which will be determined at the sole discretion of manufacturer

Damage or repairs due to service by an unauthorized agency or the use of unauthorized parts

Improper assembly, such as: no regulator, improper hook-up, etc.

Damage or repairs related to spider or insect nesting

Damage due to weather conditions

arranty Procedures

For service or replacement parts, please call 1-800-762-1142 for return authorization and further instructions.

All returns must be sent via prepaid freight.

Legal Rights

No one else is authorized to make any warranties on behalf of manufacturer.

THIS WARRANTY IS IN LIEU OF ANY OTHER WARRANTY, EXPRESS OR IMPLIED, ORAL OR WRITTEN, INCLUDING, BUT NOT

LIMITED TO, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

UNIFLAME SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM ANY

DEFECTIVE PRODUCT, INCLUDING, BUT NOT LIMITED TO, LOST REVENUE OR PROFITS, BUSINESS INTERRUPTION,

OR ANY LEGAL THEORY UPON WHICH ANY CLAIM MAY BE BASED.

PURCHASER ASSUMES ALL RISK IN THE ASSEMBLY AND OPERATION OF THIS UNIT. FAILURE TO FOLLOW THIS MANUAL’S

WARNINGS AND INSTRUCTIONS CAN RESULT IN SEVERE PERSONAL INJURY, DEATH OR PROPERTY DAMAGE.

Some states do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation relevant to incidental or

consequential damages.

This warranty gives you specific legal rights. You may also have other legal rights which vary from state to state.

Since product improvement is an ongoing process at the manufacturer, we reserve the right to change this product’s

specifications or design without notice.

Owner’s manual and assembly instructions: 91000 portable outdoor heater 7/02

Contact 1-800-762-1142 for assistance.

Do not return to place of purchase.

Specifications

Certifications:

CSA International Requirement 5.90

Canadian National Standard CAN1-2.23-M82

Rating:

Maximum 14,000 BTU/hr. input

Heat Range:

Up to 10 foot diameter

Fuel:

Liquid Propane Gas (LP)

Cylinder Size:

Nominal 20 lb / 5 Gallon

14.1 oz. (400 grams)

16.4 oz. (465 grams)

Inlet gas supply pressure:

Maximum – 150 PSI

Minimum – 5 PSI

Manifold Pressure:

11.00 in. W.C.

Supply Pressure:

0.41 psig (11.00 in. W.C.)

Engine:

IPP E8

Safety Features:

100% Burner shut-off

Tilt Switch

Manufacturer:

UniFlame Corporation

Made In:

China

Owner’s manual and assembly instructions: 91000 portable outdoor heater 7/02

Contact 1-800-762-1142 for assistance.

Do not return to place of purchase.

La page est en cours de chargement...

Blue Rhino Electric Heater 91000 Manuel utilisateur

Marque: Blue Rhino

Modèle: Electric Heater 91000

Taper: Manuel utilisateur

Ce manuel convient également à

91000

Télécharger le PDF

rapport

dans d''autres langues

English: Blue Rhino Electric Heater 91000 User manual

Documents connexes

Autres documents

Eureka 2572202 Manuel utilisateur