Wells Manufacturing H-2412G Mode d'emploi

Marque: Wells Manufacturing

Modèle: H-2412G

Catégorie: Cuisinières

Taper: Mode d'emploi

WELLS BLOOMFIELD, LLC

10 Sunnen Dr., St. Louis, MO 63143

telephone: 314-678-6314

fax: 314-781-2714

www.wellsbloomfield.com

IMPORTANT: DO NOT DISCARD THIS MANUAL

This manual is considered to be part of the appliance and is to be given to the OWNER or

MANAGER of the restaurant, or to the person responsible for TRAINING OPERATORS of

this appliance. Additional manuals are available from your WELLS DEALER.

THIS MANUAL MUST BE READ AND UNDERSTOOD BY ALL PERSONS USING OR

INSTALLING THIS APPLIANCE. Contact your WELLS DEALER if you have any

questions concerning installation, operation or maintenance of this equipment.

OPERATION

MANUAL

for

COUNTER TOP

GAS HOTPLATE

Model

H-2412G

INSTANT-ON

Includes

INSTALLATION

USE & CARE

228

p/n 2M-306916 Rev. E M228 120210

Model H-2412G

Instant-On

FOR YOUR SAFETY

Do not store gasoline or other ammable liquids in the vicinity of this or any

other appliance.

WARNING:

Improper installation, adjustment, alteration, service or maintenance can cause

property damage, injury or death. Read the installation, operating and maintenance

instructions thoroughly before installing or servicing this equipment.

IMPORTANT:

The purchaser of this equipment must post in a prominent location instructions to be followed in the

event the user smells gas. This information shall be obtained by consulting the local gas supplier.

M228 2M-306916 OpM H-2412 Instant-On Dual Pilot Gas Hotplate

Unless otherwise specied, all commercial cooking

equipment manufactured by WELLS BLOOMFIELD, LLC is

warranted against defects in materials and workmanship

for a period of one year from the date of original installation

or 18 months from the date of shipment from our factory,

whichever comes rst, and is for the benet of the original

purchaser only.

THIS WARRANTY IS THE COMPLETE AND ONLY

WARRANTY, EXPRESSED OR IMPLIED IN LAW

OR IN FACT, INCLUDING BUT NOT LIMITED TO,

WARRANTIES OF MERCHANTABILITY OR FITNESS

FOR ANY PARTICULAR PURPOSE, AND/OR FOR

DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES IN

CONNECTION WITH WELLS BLOOMFIELD PRODUCTS.

This warranty is void if it is determined that, upon inspection

by an authorized service agency, the equipment has been

modied, misused, misapplied, improperly installed, or

damaged in transit or by re, ood or act of God. It also

does not apply if the serial nameplate has been removed,

or if service is performed by unauthorized personnel.

The prices charged by Wells Bloomeld for its products

are based upon the limitations in this warranty. Seller’s

obligation under this warranty is limited to the repair of

defects without charge by a Wells Bloomeld factory

authorized service agency or one of its sub-service

agencies. This service will be provided on customer’s

premises for non-portable models. Portable models (a

device with a cord and plug) must be taken or shipped

to the closest authorized service agency, transportation

charges prepaid, for service. In addition to restrictions

contained in this warranty, specic limitations are shown in

the Service Policy and Procedure Guide. Wells Bloomeld

authorized service agencies are located in principal cities.

This warranty is valid in the United States and Canada and

void elsewhere. Please consult your classied telephone

directory, your foodservice equipment dealer or contact:

Wells Bloomeld, LLC

10 Sunnen Dr., St. Louis MO 63143 USA

phone (314) 678-6314 or fax (314) 781-2714

for information and other details concerning warranty.

LIMITED WARRANTY STATEMENT

SERVICE POLICY AND PROCEDURE GUIDE and ADDITIONAL WARRANTY EXCLUSIONS

NOTE: For your protection, please note that equipment

in this shipment was carefully inspected and packaged

by skilled personnel before leaving the factory. Upon

acceptance of this shipment, the transportation company

assumes full responsibility for its safe delivery.

IF SHIPMENT ARRIVES DAMAGED:

1. VISIBLE LOSS OR DAMAGE: Be certain that any

visible loss or damage is noted on the freight bill or

express receipt, and that the note of loss or damage is

signed by the delivery person.

2. FILE CLAIM FOR DAMAGE IMMEDIATELY:

Regardless of the extent of the damage.

3. CONCEALED LOSS OR DAMAGE: if damage is

unnoticed until the merchandise is unpacked, notify the

transportation company or carrier immediately, and le

“CONCEALED DAMAGE” claim with them. This

should be done within fteen (15) days from the date

the delivery was made to you. Be sure to retain the

container for inspection.

Wells Bloomeld cannot assume liability for damage or loss

incurred in transit. We will, however, at your request, supply

you with the necessary documents to support your claim.

SHIPPING DAMAGE CLAIM PROCEDURE

1. Resetting of safety thermostats, circuit breakers, over

load protectors, and/or fuse replacements are not

covered by this warranty unless warranted conditions

are the cause.

2. All problems due to operation at voltages or phase

other than specied on equipment nameplates are

not covered by this warranty.

Conversion to correct voltage and/or phase must be

the customer’s responsibility.

3. All problems due to electrical connections not made

in accordance with electrical code requirements

and wiring diagrams supplied with the equipment are

not covered by this warranty.

4. Replacement of items subject to normal wear, to

include such items as knobs, light bulbs; and, normal

maintenance functions including adjustments of

thermostats, adjustment of micro switches and

replacement of fuses and indicating lights are not

covered by warranty.

5. Damage to electrical cords and/or plug due to exposure

to excessive heat are not covered by this warranty.

6. Full use, care, and maintenance instructions supplied

with each machine. Noted maintenance and

preventative maintenance items, such as servicing and

cleaning schedules, are customer responsibility.

Those miscellaneous adjustments noted are customer

responsibility. Proper attention to preventative

maintenance and scheduled maintenance procedures

will prolong the life of the appliance.

7. Travel mileage is limited to sixty (60) miles from an

Authorized Service Agency or one of its sub-service

agencies.

8. All labor shall be performed during regular working

hours. Overtime premium will be charged to the buyer.

9. All genuine Wells replacement parts are warranted

for ninety (90) days from date of purchase on non-

warranty equipment. This parts warranty is limited only

to replacement of the defective part(s). Any use of

non-genuine Wells parts completely voids any

warranty.

10. Installation, labor, and job check-outs are not

considered warranty and are thus not covered by this

warranty.

11. Charges incurred by delays, waiting time or operating

restrictions that hinder the service technician’s ability to

perform service are not covered by warranty. This

includes institutional and correctional facilities.

M228 2M-306916 OpM H-2412 Instant-On Dual Pilot Gas Hotplate

WARRANTY xi

SPECIFICATIONS 1

FEATURES & OPERATING CONTROLS 2

PRECAUTIONS & GENERAL INFORMATION 3

AGENCY APPROVAL INFORMATION 3

INSTALLATION 4

INITIAL ADJUSTMENT 7

OPERATION 8

TROUBLESHOOTING 10

CLEANING INSTRUCTIONS 11

ASSEMBLY DIAGRAM 12

PARTS & SERVICE 13

CUSTOMER SERVICE DATA 13

Thank You for purchasing this

Wells Bloomeld appliance.

Proper installation, professional

operation and consistent

maintenance of this equipment

will ensure that it gives you the

very best performance and a long,

economical service life.

This manual contains the

information needed to properly

install this equipment, and to use

and care for the equipment in a

manner which will ensure its

optimum performance.

TABLE OF CONTENTS

SPECIFICATIONS

MODEL

COOKING

SURFACE

STYLE FUEL

MANIFOLD

PRESSURE

B.T.U /HR/

BURNER

TOTAL

B.T.U./HR

H-2412G

Instant-On

Dual Pilot

11-7/32” Wide,

22-27/32” Deep

2 BURNERS

WITH INDIVIDUAL

CONTROL

Natural

Gas

5.0” W.C. 12,000 24,000

Propane 10.0” W.C. 12,000 24,000

BURNERS Provide cooking heat

Front and rear burners are individually controllable

Removable for easy cleaning

BURNER CONTROL Provide individual control of front and rear burners

KNOBS

PILOT LIGHT Provides ignition source for main burners

ACTUATOR Admits gas to burner when depressed. Actuator head removable

for easy cleaning

GRATE ASSEMBLY Holds food product at proper distance from burner ame

Removable for easy cleaning

DRIP TRAY Catches drippings

Removable for easy cleaning

ADJUSTABLE LEGS Allow for ventilation under hotplate. Provide means of

leveling the appliance, and of cleaning underneath

NAMEPLATE Gives Manufacturer, Model and Serial Number

(on back—not shown) Also provides fuel specications and agency approval information

FEATURES & OPERATING CONTROLS

Fig. 1 Countertop Gas Hotplate - Features & Operating Controls

M228 2M-306916 OpM H-2412 Instant-On Dual Pilot Gas Hotplate

M228 2,M-306916 OpM H-2412 Instant-On Dual Pilot Gas Hotplate

This appliance is intended for use in commercial establishments

only.

This appliance is intended

to prepare food for human consumption.

No other use is

recommended or authorized by the manufacturer or its

agents.

This hotplate must be installed by a technician qualied and certied or

licensed to install gas-red equipment. A licensed technician must

perform the initial startup and adjustment of this appliance.

Operators of this appliance must be familiar with the appliance use,

limitations and associated restrictions. Operating instructions must be

read and understood by all persons using or installing this appliance.

Cleanliness of this appliance is essential to good sanitation. Read and

follow all included cleaning instructions and schedules to ensure the

safety of the food product.

DO NOT submerge hotplate or burners in water. DO NOT splash

or pour water into interior of hotplate. Burners which have been

allowed to become wet must be thoroughly dried before use.

Hotplate must be operated with supplied 4” legs properly

installed.

The technical content of this manual, including any parts breakdown

illustrations and/or adjustment procedures, is intended for use by

qualied technical personnel only.

Any procedure which requires the use of tools must be performed by a

qualied technician.

This manual is considered to be a permanent part of the appliance.

This manual and all supplied instructions, diagrams, schematics, parts

breakdown illustrations, notices and labels must remain with the

appliance if it is sold or moved to another location.

This appliance is made in the USA. Unless otherwise noted, this

appliance has American sizes on all hardware.

This unit complies with NSF standard 4 only if maintained and

operated per the instructions in this manual.

This appliance meets ANSI Z83.11 specications for gas-red food

service equipment.

This appliance is CSA listed for gas operation.

WARNING:

FIRE HAzARD

In the event a gas odor is

detected, shut down the unit

at the main gas shutoff and

contact your local gas supplier

from a neighboring location

for service.

CAUTION:

FALL HAzARD

DO NOT stand or sit on the

hotplate.

CAUTION:

FALL HAzARD

DO NOT use the hotplate as a

stool or ladder.

PRECAUTIONS AND GENERAL INFORMATION

AGENCY APPROVAL INFORMATION

STD 4

WARNING

INSTALLATION

NOTE: DO NOT discard

the carton or other packing

materials until you have

inspected the appliance for

hidden damage and tested it

for proper operation.

Refer to SHIPPING DAMAGE

CLAIM PROCEDURE on the

inside front cover of this

manual.

DANGER:

HEALTH

HAzARD

This appliance must be

properly ventilated.

Failure to provide proper

ventilation of exhaust

gasses can result in severe

injury and death.

WARNING:

FIRE HAzARD

Do not store ammable or

combustible materials near this

appliance. The open ame of

this appliance can cause such

materials to ignite.

NOTICE:

Manufacturer’s warranty on

this hotplate is in effect only

when the hotplate is installed

and operated in accordance

with these instructions and

local codes and ordinances or,

in the absence of local codes,

the National Fuel Gas Code,

ANSI Z223.1 (current edition).

The manufacturer of the

hotplate assumes no liability

for any damage resulting from

failure to comply with this

notice.

UNPACKING & INSPECTION

Carefully remove the hotplate from the carton. Remove all

protective plastic lm, packing materials and accessories from the

hotplate before connecting the hotplate to fuel gas or otherwise

performing any installation procedure.

Carefully read all instructions in this manual and the Installation

Instruction Sheet packed with the hotplate before starting any

installation.

Read and understand all labels and diagrams attached to the

hotplate.

Carefully account for all components and accessories before

discarding packing materials. Store all accessories in a convenient place

for later use.

Thoroughly clean the appliance before use. See Cleaning

Instructions, page 11.

SETUP

Setup the hotplate only on a rm, level, non-combustible surface.

The hotplate must be leveled with a spirit level in its nal operational

position, prior to beginning the gas piping installation.

Clearances to adjacent surfaces must be maintained.

Maintain a minimum of 3” from hotplate sides and 3” from rear of the

hotplate to combustible walls; 0” from sides and rear of the hotplate

to non-combustible walls; and; 4” from non-combustible counter as

established by provided 4” legs. Supplied legs must be properly

installed. Once installed, the legs should NOT be removed.

Maintain adequate clearances for cleaning and proper operation.

The hotplate must be installed in an area with sufcient make-up air for

proper combustion, and must be installed such that the ow of combustion

and ventilation air will not be obstructed.

For servicing, Wells Mfg. recommends 6” clearance from rear of the

hotplate to wall.

When used with an exhaust fan, special precautions must be observed to

avoid interference with the operation of the hotplate, such as drafts and air

starvation.

The current edition of NFPA 96 (Standard for the Installation of

Equipment for the Removal of Smoke and Grease Laden Vapors from

Commercial Cooking Equipment) species ventilation requirements to

ensure the removal of exhaust gasses and products of combustion.

IT IS THE RESPONSIBILITY OF THE INSTALLER TO ENSURE THAT

THIS GAS HOTPLATE INSTALLATION CONFORMS TO ALL

APPLICABLE CODES AND ORDINANCES.

The area where the hotplate is installed must be kept clear of combustibles

and ammables. This includes mops, rags, grease, wrapping paper and

electric cords.

M228 2M-306916 OpM H-2412 Instant-On Dual Pilot Gas Hotplate

WARNING

M228 2M-306916 OpM H-2412 Instant-On Dual Pilot Gas Hotplate

INSTALLATION (continued)

GAS APPLIANCE CODE COMPLIANCE

The installation of gas piping from the outlet side of the gas meter or

service regulator to the hotplate must be performed by a technician

qualied and certied or licensed to install gas-red equipment.

A licensed and qualied technician must perform the initial startup and

adjustment of this appliance.

The installation of this gas-red appliance must conform to local

codes, or in the absence of such codes, with the current edition of

National Fuel Gas Code ANSI Z223.1.

For use in the State of Massachusetts, this appliance must be

installed in compliance with Massachusetts Fuel Gas and Plumbing

Code CMR 248.

The installation of this gas-red appliance must comply with

applicable portions of NFPA 96 for ventilation.

The venting of this appliance must not be obstructed, nor may such

venting interfere with the ow of combustion air required for proper

operation of the gas burners.

Additionally:

1. The gas supply line used to connect the hotplate to the gas

supply system must be black iron pipe, or other material as

approved by local ordinance for gas piping.

2. Gas supply piping must be inside 3/8” diameter or greater.

3. Use pipe sealant made specically for gas piping on all pipe

joints. Apply sealant sparingly to the male threads only.

Sealant must be resistant to the action of LP gas.

4. Verify that all supply piping is clean and free of obstructions, dirt,

chips and pipe sealant compound prior to installation.

5. All pipe joints must be checked for leaks before lighting. Leak

checks should be performed with a soap and water solution.

NEVER CHECK FOR LEAKS WITH AN OPEN FLAME.

DANGER:

FIRE AND

EXPLOSION HAzARD

NEVER use an open ame to

check for gas leaks. Fire and

explosion may result.

IMPORTANT:

All pipe joints must be checked

for leaks before lighting. Leak

checks should be performed

with a soap and water solution.

IMPORTANT:

Information on the

construction and installation of

ventilating hoods may be

obtained from the current

edition of NFPA 96

Standard for the Installation of

Equipment for the Removal of

Smoke and Grease Laden

Vapors from Commercial

Cooking Equipment.

Copies of this standard are

available from the

Nation Fire Protection Assn.:

NFPA

1 Batterymarch Park

P.O. Box 9101

Quincy, MA 02269-9101

INSTALLATION (continued)

INSTALLING THE HOTPLATE

Refer to the nameplate. Verify the fuel type and pressure, which must

match the nameplate specications. Connecting the hotplate to the

wrong fuel type and/or pressure will compromise the safety and/or

performance of the appliance.

The hotplate must be placed in its nal operational position and

leveled front-to-back and side-to-side, with a spirit level, prior to

beginning the gas piping installation. Re-check the level of the unit at

the conclusion of the gas piping installation.

Each gas hotplate is supplied with a separate gas pressure regulator,

which must be installed on the manifold pipe protruding from the rear

of the hotplate. Ensure that the regulator is installed such that the

ow arrow stamped on the body of the regulator points toward the

hotplate. Failure to properly install the supplied regulator will result in

an extremely hazardous condition.

A moisture trap (drip leg) consisting of a tee, 4” nipple pointing down,

and cap must be installed upstream of the gas pressure regulator.

A manual gas shut-off valve may be required by local codes and

is, in any case, strongly recommended. The shut-off valve must

be installed between the gas supply piping and the gas pressure

regulator.

It is the responsibility of the gas piping installer toidentify the code

requirement for a shut-off valve.

Shut-off valves, moisture trap and all associated piping must

besupplied by the gas piping installer.

DANGER:

FIRE AND

EXPLOSION HAzARD

NEVER use an open ame to

check for gas leaks. Fire and

explosion may result.

IMPORTANT:

All pipe joints must be checked

for leaks before lighting. Leak

checks should be performed

with a soap and water

solution.

WARNING:

FIRE HAzARD

This hotplate is supplied with a

gas pressure regulator.

Failure to properly install the

supplied regulator will result in

an extremely hazardous

condition.

Flow arrow stamped on body

of regulator must point toward

the hotplate.

Regulator adjusting screw and

vent hole must point UP.

IMPORTANT:

Verify fuel gas type. If the

available fuel does not match

the nameplate specication,

exchange the hotplate for the

correct type. DO NOT attempt

to modify a unit in the eld to

accept a different fuel.

IMPORTANT:

Avoid damage to the regulator:

if the gas supply piping system

is pressure tested at pressures

exceeding 1/2 psig (3.45kPa),

the hotplate must be isolated

or disconnected from the gas

piping system for the duration

of the test.

Fig. 2 Gas Supply Piping

M228 2M-306916 OpM H-2412 Instant-On Dual Pilot Gas Hotplate

IL1638

WARNING

M228 2M-306916 OpM H-2412 Instant-On Dual Pilot Gas Hotplate

INITIAL ADJUSTMENT

SET GAS PRESSURE:

Turn the gas shut-off valve OFF.

A gas pressure test tap is provided on the gas supply manifold.

Remove both burner control knobs and the front panel. Remove

plug in gas pressure test tap and attach a manometer.

Turn the shut-off valve ON. Light the pilot light and turn both gas

control valves to HI. Depress both actuator heads.

Remove the cap from the pressure regulator. Turn the adjusting

screw clockwise to increase pressure; counter-clockwise to

decrease pressure. Adjust the gas pressure regulator for:

5” water column (natural gas); or, 10” water column (propane).

When nished, replace cap on regulator, turn shut-off valve OFF,

remove manometer and reinstall plug in tap. Reassemble

hotplate, turn shut-off valve back ON and relight pilot light.

SET PILOT FLAMES:

Remove left side (rear burner) control knob by pulling straight off.

Pilot ame adjustment screw is located to the right side of the

burner control valve.

Using a small, at-blade screwdriver, turn the screw clockwise to

decrease the ame size, or counter-clockwise to increase the

ame size.

Burner should light quickly and completely when burner actuator

is depressed. Adjust pilot ame to 1/4” high. Drafty conditions

may require a higher ame to allow pilot ame to remain lit.

Reinstall the control knob.

ADJUST BURNER FLAME:

CAUTION: BURN HAZARD

Wear heat protective gloves. Avoid contact with ame.

Remove grate, drip tray and actuator heads. Turn both burner

control knobs full on. Adjust one burner at a time.

Loosen locking screw on a burner assembly shutter. Using a

metal implement such as a long-handle ladle, press the actuator

to light burner.

Turn shutter to admit more or less air as required. Adjust air

shutter until ame is mostly blue in color.

Tighten locking screw. Reassemble hotplate when nished.

IMPORTANT:

Pressure adjustment must

be performed by a qualied

technician only.

Fig. 3 Gas Pressure Adjustment

IMPORTANT:

Flame adjustment must be

performed by a qualied

technician only.

Fig. 4 Pilot Flame Adjustment

NOTE:

The right knob controls the front

burner; the left knob controls

the rear burner.

Fig. 5 Burner Flame Adjustment

IL1639

IL1640

IL1641

OPERATION

GENERAL OPERATIONAL NOTES

Carefully read the description of the hotplate operation on the

specication sheet.

Do NOT use this appliance if it has been submerged in water.

Call a qualied technician to examine the appliance and to service or

replace any component which has been submerged. Burners which

have been allowed to become wet must be thoroughly dried

before use.

For initial startup, and any time the gas supply has been shut-off, it

may take several minutes to light the pilot as air in the piping and

manifolds is purged.

The burner control knobs must be turned by hand only. Never use

tools to turn the control knob. If the knob will not turn by hand, do

NOT attempt to force or repair it. Contact your Authorized Wells

Service Agency for repairs. Forced or improperly repaired valves

pose the risk of re and/or explosion.

Make sure burners, pilot burner, drip tray, actuators and grate

assembly are properly installed before attempting to operate.

LIGHTING THE PILOT FLAMES

Before lighting the pilot light, smell all around the appliance area for

gas. Be sure to smell near oor level because some gas is heavier

than air and will settle to the oor.

For initial startup, and any time the gas supply has been shut-off, it

may take several minutes to light the pilot as air in the piping and

manifolds is purged.

The pilot ame must be lighted by hand:

Turn both control knobs to the full OFF position.

Be sure the gas shut-off valve is ON and the appliance has had

time for the air to be purged from the lines.

Remove the grate and drip pan. The pilots are located adjacent

to their respective burner.

Light the pilot with a long match or replace lighter.

Use of a cigarette lighter is NOT recommended.

IF THE UNIT DOES NOT LIGHT or IN THE EVENT OF A GAS

INTERRUPTION:

Turn main valve to unit. Wait 5 minutes for gas to clear.

Turn off all knobs and pilot valves.

Turn on main valve and light pilots.

Turn burner knobs to desired setting. Depress actuator to light

burner.

SHUT DOWN INSTRUCTIONS

Turn all burner knobs to OFF.

Turn all pilots OFF.

Turn the main gas supply OFF.

WARNING:

FIRE HAzARD

IF YOU SMELL GAS:

¤ DO NOT try to light

any appliance.

¤ DO NOT touch any

electrical switch

¤ DO NOT use any

telephone in your

building.

IF YOU SMELL GAS:

Shut down the unit at the main

gas shutoff valve and contact

your local gas supplier from a

neighboring location.

Follow the instructions

received from the gas

supplier immediately

and exactly.

CAUTION:

BURN HAzARD

DO NOT press either actuator

by hand. The burner will

light anytime the plunger is

pressed.

M228 2M-306916 OpM H-2412 Instant-On Dual Pilot Gas Hotplate

WARNING

M228 2M-306916 OpM H-2412 Instant-On Dual Pilot Gas Hotplate

WARNING:

FIRE HAzARD

NEVER attempt to force or

repair a stuck control valve.

Contact your Authorized Wells

Service Agency for repairs.

Forced or improperly repaired

valves pose the risk of re

and/or explosion.

WARNING:

FIRE AND

EXPLOSION

HAzARD

If the pilot light should be

extinguished, turn off the gas

shut-off valve and remove

grate and drip pan. Allow

appliance to vent for ve

minutes before attempting

to re-light.

CAUTION:

HOT SURFACE

Exposed surfaces can

be hot to the touch and may

cause burns.

CAUTION:

BURN HAzARD

DO NOT press either actuator

by hand. The burner will

light anytime the plunger is

pressed.

OPERATION (continued)

WARNING: FIRE HAzARD

Turn control valves OFF when hotplate is not in use.

Failure to turn valves off will allow unattended burner to light

should actuator be depressed.

WARNING: FIRE AND EXPLOSION HAzARD

DO NOT set anything on grate other than cookware to be

heated. Pilot ame may be extinguished if blocked.

Anything placed on the burners will open the gas valves,

which can cause a re or explosion.

OPERATION

Inspect the unit for cleanliness before use. Clean as necessary:

See Cleaning Instructions, page 11.

Be sure the pilot light is lit before operation. See Lighting the Pilot

Light, page 8.

The burner control knobs must be turned by hand only. Never use

tools to turn the control knob.

The control used in this gas hotplate provides a continuous range of

settings from OFF to HI.

The right knob controls the front burner

The left knob controls the rear burner

Light burner by turning control knob to the HI position. Place cookware

on burner to depress the burner actuator. Fire will form in a complete

ring around the burner.

Set the control knob to the desired heat level. The setting can be

readjusted at any time.

The burner ame will automatically extinguish when cookware is

removed and the actuator is no longer depressed.

Fig. 6 Temperature Control

IL1642

WARNING

TROUBLESHOOTING

M228 2M-306916 OpM H-2412 Instant-On Dual Pilot Gas Hotplate

SYMPTOM POSSIBLE CAUSE SUGGESTED REMEDY

Pilot will not light

Gas supply off Check main / unit gas valves

Air in lines Turn gas valve on. Attempt to light pilot every

15 sec.

Pilot valve not on Turn pilot valve on / adjust

Pilot burner holes are plugged Clean pilot burner

Front or rear burner won’t light

Actuator not depressed Burner should light only when a pot or pan

depresses actuator. Be sure actuator is properly

assembled to arm

Pilot ame not lit Turn off gas — allow unit to vent for 5 minutes.

Turn gas back on and light both pilots

Control not on Turn temperature control to HI, Set to desired

setting when lit

Water in burner Remove burner and dry thoroughly

Damaged temperature control valve, burner, actuator

valve or other internal component

Contact Authorized Wells Service Agency for

repairs

Burner not hot enough

Control valve not set Adjust for desired temperature

Shutter or nozzle out of adjustment Contact qualied technician for adjustment

Damaged temperature control valve, burner actuator

or other internal component

Contact Authorized Wells Service Agency for

repairs

NOTE: There are no user serviceable components in the burner assemblies or in the control valves. In all cases of

damage or malfunction, contact your Authorized Wells Service Agency for repairs.

M228 2M-306916 OpM H-2412 Instant-On Dual Pilot Gas Hotplate

CLEANING INSTRUCTIONS

PREPARATION

Turn gas shut-off valve OFF before cleaning.

Allow hotplate to cool completely before cleaning.

FREQUENCY: Daily

TOOLS

Bristle Brush

Clean Cloth or Sponge

Mild Detergent

Cleaner Formulated for Stainless Steel

Warm Water

CLEANING

Turn gas shut-off valve OFF before cleaning.

Allow hotplate to cool completely before cleaning.

Remove grate and drip tray by lifting from cabinet. Slide actuator heads

off actuator arms.

Note position of front and rear burner assemblies in cabinet. Remove

burner assemblies.

Clean food particles from grate, actuator heads, drip tray and crumb

tray with warm water, mild detergent and a bristle brush. Rinse with

clean water. Wipe dry with a soft clean cloth.

Examine burner assemblies. Note position of air shutters before

cleaning. Clean food particles from burners with warm water, mild

detergent and a bristle brush. Rinse by wiping with a soft cloth

dampened with clean water. Wipe exterior surfaces dry with a soft

clean cloth. Allow burners to air dry so that interior passages are

completely free of water.

Wipe the outer portions of the hotplate cabinet with a clean soft cloth

or sponge dampened with warm water and a mild detergent or cleaner

formulated for cleaning stainless steel. DO NOT use steel wool to

clean hotplate cabinet. Rinse by wiping hotplate cabinet with a clean

soft cloth or sponge moistened with clean warm water. Dry cabinet by

wiping with a clean soft dry cloth.

Examine burners to be sure the air shutters are in their proper position.

Reinstall burner assemblies in cabinet (see g. 7, page 12):

Burner with short venturi is the REAR burner.

Venturi / air shutter slides over left nozzle.

Fingers on burner bracket slide into rear notches in center brace.

Burner with long venturi is the FRONT burner.

Venturi / air shutter slides over right nozzle.

Fingers on burner bracket slide into front notches in center brace.

Turn shut-off valve ON and light pilot ame.

Reinstall drip tray, actuator heads and grate.

Procedure is complete.

WARNING:

FIRE HAzARD

Shut off the gas

supply valve before cleaning.

CAUTION:

BURN HAzARD

Allow hotplate to cool

completely before cleaning.

IMPORTANT: DO NOT spill

or pour water into controls,

DO NOT submerge hotplate

cabinet in water. Damage to

internal components will

occur. Damage to internal

components from water

damage is NOT covered by

warranty.

DO NOT steel wool or

metal scouring pads to clean

cabinet, drip tray or crumb

tray.

Good sanitation is vital to the

quality of the nal food

product. Be sure to clean

in all corners and crevices

where grease and other

cooking debris can

accumulate.

WARNING

CLEANING INSTRUCTIONS (continued)

Fig. 7 Hotplate Assembly

M228 2M-306916 OpM H-2412 Instant-On Dual Pilot Gas Hotplate

IL1643

NOTE

M228 2M-306916 OpM H-2412 Instant-On Dual Pilot Gas Hotplate

EXPLODED VIEW: H-2412G GAS HOTPLATE

Model: H-2412GIO

COUNTERTOP GAS HOTPLATE

PL228

IL1812 Rev. D 11/15/11

Old Valve

Design use kit: WS-WL0262

M228 2M-306916 OpM H-2412 Instant-On Dual Pilot Gas Hotplate

PARTS LIST: H-2412G GAS HOTPLATE

M228 2M-306916 OpM H-2412 Instant-On Dual Pilot Gas Hotplate

H-2412G COUNTERTOP GAS HOTPLATE

Fig No Part No. Description

1 WS-506707 GRATE ASSY H2412G LAVISTA

2 I7-306331 ACTUATOR HEAD (REMOVABLE)

3 I7-306706 PAN TOP ASSY (DRIP PAN)

4 2F-306905 BURNER FRONT H2412G

5 I7-39322 PANEL FR H2412G

6 2M-300534 TRADEMARK DOMED LABEL

7 2C-33935 SCREW 6ABX5/16 PH PAN SMS

8 2R-Y5052 FEET ADJ 4GRAY 3/8-16

9 2F-306906 BURNER REAR H2412G

10 2C-39319 CLIP HORSESHOE (2 REQ)

2J-39007 REGULATOR PRESSURE GAS

2J-39284 REGULATOR GAS LP

12 2J-306342 PILOT ASSY 3/16 TUBE

13 2K-306350 TEE BRS 3/16CCX3/16CCX3/16

14 WS-506860 KIT SERV H2412G ACTUATOR

15 M3-506919 TUBE SS 1/40 X 4 FLEX FR

16 2R-39325 KNOB CONTROL ASSY FRONT

17 2R-39327 KNOB CONTROL ASSY REAR

WS-WL0262 MANUAL VALVE REPLACEMENT KIT

2V-Z15185 VALVE MANUAL GAS HOTPLATE

19 M3-506917 TUBE SS 1/4D X 16 FLEX FR

20 2P-39245 PLUG HEX HEAD 1/8 NPT BRA

21 2K-39315 FTG PILOT ADJ 3/16 TUBE

22 2K-39313 MANIFOLD PIPT H2412G

23 1L-306920 TUBE SS 1/4DX17 FLEX REAR

2A-39335 ORIFICE HOOD #53, NAT

2A-39338 ORIFICE HOOD #60, LP

25 2K-306349 ELBOW ORIFICE 1/4CC X 3/8

26 1L-306918 TUBE SS 1/4D X 5.5 FLEX

27 2V-306352 VALVE SHUTOFF H2412GINSTA

28 I7-306333 ARM PIVOT H2412G

29 2C-305361 PIN COTTER HAIRPIN 1-3/16

30 2C-306344 PIN CLEVIS 7/8 X .182DIA

31 2C-35455 NUT 8-32 HEX MS SS

32 I7-306332 ARM ACTUATOR ASSY

33 2C-306343 PIN CLEVIS 1 1/2 X .182 DIA

34 2P-306346 SPRING TORSION

35 2K-Z15302 FITTING .25CC X 3/8-27UNS

DESCRIPTION

PART NO.

CUSTOMER SERVICE DATA

please have this information available if calling for service

RESTAURANT _____________________________ LOCATION _____________

INSTALLATION DATE ________________________ TECHNICIAN ___________

SERVICE COMPANY ________________________________________________

ADDRESS ___________________________ STATE ______ ZIP__________

TELEPHONE NUMBER (_____)_____-_________ EQUIPMENT MODEL NO. _______________

EQUIPMENT SERIAL NO. _______________

FUEL: (check one)  Natural Gas  LP / Propane

PARTS & SERVICE

DESCRIPTION SERVICE

PART NO.

LEGS, PLASTIC 4” 2R-Y5092

DRIP TRAY, DUAL PILOT HOTPLATE I7-306706

GRATE, STAINLESS STEEL I7-306707

IMPORTANT: Use only

factory authorized service parts

and replacement lters.

For factory authorized service,

or to order factory authorized

replacement parts, contact

your Wells authorized service

agency, or call:

Wells Bloomeld, LLC

10 Sunnen Drive

St. Louis, MO 63143

Service Parts Dept.

phone: (314) 678-6314

fax: (314) 781-2714

Service Parts Department

can supply you with the name

and telephone number of

the WELLS AUTHORIZED

SERVICE AGENCY nearest

you.

DIRECTIVES DE NETTOYAGE (suite)

Fig. 7 Assemblage de la plaque chauffante

M228 2M-306916 OpM H-2412 Instant-On Dual Pilot Gas Hotplate

IL1643-FR

1. BRÛLEUR ARRIÈRE

Se glisse sur la buse

GAUCHE; se fixe aux

encoches ARRIÈRE du

support de la veilleuse

Le bras de l’activateur

arrière se fixe par le

centre du brûleur

4. ASSEMBLAGE DE LA GRILLE

Se fixe au-dessus des brûleurs

Les têtes de l’activateur

s’enroulent autour de la

tige centrale de la grille

3. PLATEAU D’ÉGOUTTAGE

Se fixe en exposant le

dessus des brûleurs

Les têtes de

l’activateur se

glissent sur les

extrémités des

bras de l’activateur

2. BRÛLEUR AVANT

Se glisse sur la buse DROITE;

se fixe aux encoches AVANT du

support de la veilleuse

Le bras de l’activateur

avant se fixe par le

centre du brûleur

M228 2M-306916 OpM H-2412 Instant-On Dual Pilot Gas Hotplate

DIRECTIVES DE NETTOYAGE

PRÉPARATION

Fermer la soupape d’arrêt du gaz avant de procéder au nettoyage.

Laisser la plaque chauffante refroidir complètement avant le nettoyage.

FRÉQUENCE: Tous les jours

OUTILS

Brosse à bres

Linge ou éponge propre

Détergent doux

Nettoyant conçu pour l’acier inoxydable

Eau chaude

NETTOYAGE

Fermer la soupape d’arrêt du gaz avant de procéder au nettoyage.

Laisser la plaque chauffante refroidir complètement avant le nettoyage.

Retirer la grille et le plateau d’égouttage en les soulevant hors du boîtier. Faire

glisser les têtes d’activation hors des bras de l’activateur.

Prendre note de la position des brûleurs avant et arrière dans le boîtier. Retirer

les brûleurs.

Éliminer les particules d’aliments de la grille, des têtes d’activation, du plateau

d’égouttage et du plateau de miettes avec de l’eau chaude, un détergent doux

et une brosse à bres. Rincer avec de l’eau propre. Essuyer et sécher avec un

linge doux et propre.

Examiner l’assemblage des brûleurs. Prendre note de la position des

obturateurs d’air avant le nettoyage. Éliminer les particules d’aliments des

brûleurs avec de l’eau chaude, un détergent doux et une brosse à bres.

Rincer en frottant avec un linge doux imbibé d’eau propre. Essuyer les

surfaces extérieures avec un linge propre et doux. Laisser sécher les brûleurs

à l’air an que les passages intérieurs soient totalement exempts d’eau.

Essuyer les portions externes du boîtier de la surface chauffante avec un linge

doux et propre ou une éponge imbibée d’eau chaude et d’un détergent doux ou

d’un nettoyant conçu pour nettoyer l’acier inoxydable. NE PAS utiliser de laine

d’acier pour nettoyer le boîtier de la surface chauffante. Rincer en essuyant le

boîtier de la surface chauffante avec un linge doux et propre ou une éponge

imbibée d’eau chaude propre. Essuyer le boîtier en le frottant avec un linge sec

doux et propre.

Examiner les brûleurs pour conrmer que les obturateurs d’air sont dans la

bonne position.

Réinstaller les brûleurs dans le boîtier (se reporter à la g. 7 de la page 12) :

Le brûleur doté du petit tube Venturi est le brûleur ARRIÈRE.

Le tube Venturi / l’obturateur d’air se glisse sur la buse gauche.

Les taquets du support de brûleur se glissent dans les encoches

arrière du renfort central.

Le brûleur doté d’un long tube Venturi est le brûleur AVANT.

Le tube Venturi / l’obturateur se glisse sur la buse droite.

Les taquets de support de brûleur se glissent dans les encoches avant

du renfort central.

Ouvrir la soupape d’arrêt et allumer la amme de la veilleuse.

Réinstaller le plateau d’égouttage, les têtes d’activation et la grille.

La procédure est terminée.

WARNING:

FIRE HAzARD

Shut off the gas supply valve

before cleaning.

CAUTION:

BURN HAzARD

Allow hotplate to cool

completely before cleaning.

IMPORTANT: DO NOT spill

or pour water into controls,

DO NOT submerge hotplate

cabinet in water. Damage to

internal components will

occur. Damage to internal

components from water

damage is NOT covered by

warranty.

DO NOT steel wool or

metal scouring pads to clean

cabinet, drip tray or crumb

tray.

Good sanitation is vital to the

quality of the nal food

product. Be sure to clean

in all corners and crevices

where grease and other

cooking debris can

accumulate.

WARNING

La page charge ...

Wells Manufacturing H-2412G Mode d'emploi

Marque: Wells Manufacturing

Modèle: H-2412G

Catégorie: Cuisinières

Taper: Mode d'emploi

Télécharger le PDF

rapport

dans d''autres langues

English: Wells Manufacturing H-2412G Operating instructions

Wells Manufacturing H-2412G Mode d'emploi

Wells Manufacturing H-2412G Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents