LeftMaster HBW7675 Manuel utilisateur

Marque: LeftMaster

Modèle: HBW7675

Catégorie: Porte de garage

Taper: Manuel utilisateur

Ce manuel convient également à

PREMIUM Series Garage Door Opener

CONTENTS

Important Safety Instructions ......... 2-3

Operation....................................4

Using the Door Control..................5

Programming-Door Control Panel ....6

Programming - Remote Controls ......7

To Erase the Memory ...................7

To Open the Door Manually ............8

Battery Backup*..........................8

Adjustment ..................................9

Program the Travel .................... 10

Test the Safety Reversal System .... 11

Test the Protector System

.......... 11

Maintenance .............................. 12

Troubleshooting ...................... 13-14

Repair Parts .............................. 15

Warranty .................................. 16

PREMIUM Series Garage

Door Opener

The Chamberlain Group, Inc.

845 Larch Avenue

Elmhurst, Illinois 60126-1196

■ Please read this guide and the enclosed safety materials carefully!

■ The door WILL NOT CLOSE unless the Protector System

is connected and

properly aligned.

■ Periodic checks of the garage door opener are required to ensure safe

operation.

■ This garage door opener is ONLY compatible with MyQ™ and Security✚ 2.0™

accessories.

■ DO NOT enable the Timer-to-Close feature if you are installing the garage

door opener on a one-piece door. The Timer-to-Close is to be used ONLY with

sectional doors.

■ Attach enclosed warning labels to the location indicated on label.

www.liftmaster.com

Serial Number:

Date of Purchase:

User’s Guide

FOR RESIDENTIAL USE ONLY

Write down the following information

for future reference:

The images throughout this manual are for reference and your product may look different.

CONTACT INFORMATION

Leave this Users Guide with the homeowner.

*If applicable.

Safety Symbol and Signal

Word Review

This garage door opener has been designed

and tested to offer safe service provided it

is installed, operated, maintained and tested

in strict accordance with the instructions

and warnings contained in this manual.

When you see these Safety Symbols and

Signal Words on the following pages, they

will alert you to the possibility of serious

injury or death if you do not comply

with the warnings that accompany them.

The hazard may come from something

mechanical or from electric shock. Read

the warnings carefully.

Mechanical

Electrical

When you see this Signal Word on the

following pages, it will alert you to the

possibility of damage to your garage door

and/or the garage door opener if you do not

comply with the cautionary statements that

accompany it. Read them carefully.

IMPORTANT INSTALLATION INSTRUCTIONS

To reduce the risk of SEVERE INJURY or DEATH:

WARNING

WARNING WARNING

1. READ AND FOLLOW ALL WARNINGS AND INSTRUCTIONS.

2. Install garage door opener ONLY on properly balanced and

lubricated garage door. An improperly balanced door may

NOT reverse when required and could result in SEVERE

INJURY or DEATH.

3. ALL repairs to cables, spring assemblies and other hardware

MUST be made by a trained door systems technician

BEFORE installing opener.

4. Disable ALL locks and remove ALL ropes connected

to garage door BEFORE installing opener to avoid

entanglement.

5. Install garage door opener 7 feet (2.13 m) or more above

ﬂ oor.

6. Mount the emergency release within reach, but at least 6 feet

(1.83 m) above the ﬂ oor and avoiding contact with vehicles

to avoid accidental release.

7. NEVER connect garage door opener to power source until

instructed to do so.

8. NEVER wear watches, rings or loose clothing while installing

or servicing opener. They could be caught in garage door or

opener mechanisms.

9. Install wall-mounted garage door control:

• within sight of the garage door.

• out of reach of children at minimum height of 5 feet (1.5 m).

• away from ALL moving parts of the door.

10. Place entrapment warning label on wall next to garage door

control.

11. Place manual release/safety reverse test label in plain view on

inside of garage door.

12. Upon completion of installation, test safety reversal system.

Door MUST reverse on contact with a 1-1/2" (3.8 cm) high

object (or a 2x4 laid ﬂ at) on the ﬂ oor.

13. To avoid SERIOUS PERSONAL INJURY or DEATH from

electrocution, disconnect ALL electric and battery power

BEFORE performing ANY service or maintenance.

14. DO NOT enable the Timer-to-Close functionality if operating

either one-piece or swinging garage doors. To be enabled

ONLY when operating a sectional door.

15.

SAVE THESE

INSTRUCTIONS.

Important Safety Instructions

NOTE: For complete installation instructions visit www.liftmaster.com to print the entire owner’s manual.

IMPORTANT SAFETY INSTRUCTIONS

To reduce the risk of SEVERE INJURY or DEATH:

WARNING

WARNING WARNING

1. READ AND FOLLOW ALL WARNINGS AND INSTRUCTIONS.

2. ALWAYS keep remote controls out of reach of children.

NEVER permit children to operate or play with garage door

control push buttons or remote controls.

3. ONLY activate garage door when it can be seen clearly, it

is properly adjusted, and there are no obstructions to door

travel.

4. ALWAYS keep garage door in sight and away from people

and objects until completely closed. NO ONE SHOULD

CROSS THE PATH OF THE MOVING DOOR.

5. NO ONE SHOULD GO UNDER A STOPPED, PARTIALLY

OPENED DOOR.

6. If possible, use emergency release handle to disengage

trolley ONLY when garage door is CLOSED. Use caution

when using this release with the door open. Weak or broken

springs or unbalanced door could result in an open door

falling rapidly and/or unexpectedly and increasing the risk of

SEVERE INJURY or DEATH.

7. NEVER use emergency release handle unless garage

doorway is clear of persons and obstructions.

8. NEVER use handle to pull garage door open or closed. If

rope knot becomes untied, you could fall.

9. After ANY adjustments are made, the safety reversal system

MUST be tested.

10. Safety reversal system MUST be tested every month. Garage

door MUST reverse on contact with 1-1/2" high (3.8 cm)

object (or a 2x4 laid ﬂ at) on the ﬂ oor. Failure to adjust the

garage door opener properly increases the risk of SEVERE

INJURY or DEATH.

11. ALWAYS KEEP GARAGE DOOR PROPERLY BALANCED. An

improperly balanced door may NOT reverse when required

and could result in SEVERE INJURY or DEATH.

12. ALL repairs to cables, spring assemblies and other hardware,

ALL of which are under EXTREME tension, MUST be made by

a trained door systems technician.

13. ALWAYS disconnect electric power to garage door opener

BEFORE making ANY repairs or removing covers.

14. This operator system is equipped with an unattended

operation feature. The door could move unexpectedly. NO

ONE SHOULD CROSS THE PATH OF THE MOVING DOOR.

15. DO NOT enable the Timer-to-Close functionality if operating

either one-piece or swinging garage doors. To be enabled

ONLY when operating a sectional door.

16.

SAVE THESE

INSTRUCTIONS.

Important Safety Instructions

Your garage door opener is equipped with features to provide you with greater control over

your garage door operation. Accessories provided with your garage door opener will vary

depending on the garage door opener model purchased.

ALERT2CLOSE

The Alert2Close feature provides a visual and an audible alert that an unattended door is

closing.

TIMER-TO-CLOSE (TTC)

The Timer-to-Close feature automatically closes the door after a speciﬁ ed time period that

can be adjusted using a TTC enabled door control (Models 881LM or 880LM). Prior to and

during the door closing the garage door opener lights will ﬂ ash and the garage door opener

will beep.

MyQ™

MyQ™ technology uses a 900MHz signal to provide two-way communication between the

garage door opener and MyQ™ enabled accessories. Your garage door opener is compatible

with up to 16 MyQ™ accessories.

REMOTE CONTROLS AND DOOR CONTROLS (SECURITY✚

2.0™)

Your garage door opener has already been programmed at the factory to operate with your

remote control, which changes with each use, randomly accessing over 100 billion new

codes. Compatible with MyQ™ and Security✚ 2.0™.

NOTE: Older LiftMaster remote controls, door controls, and third party products are not

compatible.

Accessories (Security✚ 2.0™)

MEMORY CAPACITY

Remote Controls

Up to 24

Door Controls

Up to 2 Smart Control Panels or 4 of any other

Security+ 2.0™ door controls

Keyless Entries

Up to 2

THE PROTECTOR SYSTEM

(SAFETY REVERSING SENSORS)

When properly connected and aligned, the safety reversing sensors will detect an obstruction

in the path of the infrared beam. If an obstruction breaks the infrared beam while the door is

closing, the door will stop and reverse to full open position, and the opener lights will ﬂ ash

10 times. If the door is fully open, and the safety reversing sensors are not installed, or are

misaligned, the door will not close from a remote control. However, you can close the door

if you hold the button on the door control or keyless entry until the door is fully closed. The

safety reversing sensors do not affect the opening cycle.

ENERGY CONSERVATION

For energy efﬁ ciency the garage door opener will enter sleep mode when the door is fully

closed. The sleep mode shuts the garage door opener down until activated. The sleep mode

is sequenced with the garage door opener light bulb; as the light bulb turns off the sensor

LEDs will turn off and whenever the garage door opener lights turn on the sensor LEDs will

light.

LIGHTS

The garage door opener light bulbs will turn on when the opener is initially plugged in; power

is restored after interruption, or when the garage door opener is activated. The lights will turn

off automatically after 4-1/2 minutes. An incandescent A19 light bulb (100 watt maximum)

or for maximum energy efﬁ ciency a 26W (100W equivalent) compact ﬂ uorescent light (CFL)

bulb may be used.

Light Feature

The garage door opener is equipped with an added feature; the lights will turn on when

someone enters through the open garage door and the safety reversing sensor infrared beam

is broken. For added control over the light bulbs on your garage door opener, see page 6.

USING YOUR GARAGE DOOR OPENER

The garage door opener can be activated through a wall-mounted door control, remote

control, wireless keyless entry or MyQ™ accessory. When the door is closed and the

garage door opener is activated the door will open. If the door senses an obstruction or is

interrupted while opening the door will stop. When the door is in any position other than

closed and the garage door opener is activated the door will close. If the garage door opener

senses an obstruction while closing, the door will reverse. If the obstruction interrupts the

sensor beam the garage door opener lights will blink 10 times. However, you can close the

door if you hold the button on the door control or keyless entry until the door is fully closed.

The safety reversing sensors do not affect the opening cycle. The safety reversing sensor

must be connected and aligned correctly before the garage door opener will move in the

down direction.

Operation

Using the Door Control

PUSH BAR

Press the push bar to open and close the door.

LIGHT BUTTON

Press the LIGHT button to turn the garage door opener lights on or off. When the lights are

turned on they will stay on until the LIGHT button is pressed again, or until the garage door

opener is activated. Once the garage door opener is activated the lights will turn off after

the speciﬁ ed period of time (the factory setting is 4-1/2 minutes). The LIGHT button will not

control the lights when the door is in motion. The duration of the light timing can be adjusted

using the door control, see page 6.

Push Bar

Light Button

MOTION-DETECTING CONTROL PANEL

The following features are accessible by lifting the push bar:

LEARN A DEVICE

Any compatible remote controls, wireless keyless entry, or MyQ™ accessories can be

programmed to the garage door opener by pressing the Learn button on the

Motion-Detecting Control Panel.

LOCK

The LOCK feature is designed to prevent activation of the garage door opener from remote

controls while still allowing activation from the door control and keyless entry. This feature is

useful for added peace of mind when the home is empty (i.e. vacation).

AUTOMATIC LIGHT

Motion Sensor

Factory default is set to on. This feature automatically turns on the garage door opener lights

when motion is sensed. The lights will come on for the set period of time, then shut off. If

using the garage door opener light as a work light disable the motion sensor, otherwise the

light will turn off automatically if you are beyond the range of the sensor.

Light Feature

The lights will turn on when someone enters through the open garage door and the safety

reversing sensor infrared beam is broken.

MAINTENANCE ALERT SYSTEM (MAS)

This feature assists the homeowner in ensuring the garage door opener system stays in

good working condition. When the garage door opener needs to be serviced (approximately

4500 garage door opener cycles) the command (yellow) and service (red) LEDs will begin

to alternately ﬂ ash back and forth. The factory setting for the MAS feature is off and can be

activated at time of installation. Contact your installing dealer for service.

Service LED

LEARN Button

LOCK Button

Features

Lock

NOTE: Your remote controls will NOT work when LOCK mode is active however your keyless entry will still allow access to your garage.

Activate: Press and hold the LOCK button for 2 seconds. The command LED will flash as long as the lock feature is activated and your

handheld remote control will not operate your door at this time.

Deactivate: Press and hold the LOCK button again for 2 seconds. The command LED will stop flashing and normal operation will resume.

Light To change the amount of time the garage door opener lights will stay on:

Press and hold the LOCK button until the garage door opener lights ﬂ ash.* The time interval is indicated by the number of ﬂ ashes.

To cycle through the time intervals repeat the step above.

Deactivate: Press and hold the LIGHT button until the garage door opener lights turn on, then off again.*

Activate: Start with the garage door opener lights on. Press and hold the LIGHT button until the garage door opener lights turn off, then on

again.*

* Approximately 10 seconds

Motion

Sensor

Activate/Deactivate: Slide the motion sensor switch ON or OFF.

To Program

a Remote

Control or

Keyless Entry

1. Press the LEARN button on the door control to enter Programming Mode.

2. Press the LEARN button again, the LED will ﬂ ash once.

3. Remote Control: Press the button on the remote control that you wish to operate your garage door.

Keyless Entry: Enter a 4-digit personal identiﬁ cation number (PIN) of your choice on the keyless entry keypad. Then press the ENTER

button.

The garage door opener lights will ﬂ ash (or two clicks will be heard) when the code has been programmed. If programming is unsuccessful,

repeat steps 1-3 or program the remote using the learn button on the garage door opener.

Maintenance

Alert System

(MAS)

Activate/Deactivate

Press and hold the LEARN button. Then press the LIGHT button. The service LED will ﬂ ash the status; Active is 2 ﬂ ashes and deactivated is 3

ﬂ ashes.

Programming - Motion-Detecting Control Panel

Motion Sensor

Switch

Service

LED

LEARN

Button

LOCK

Button

Motion

Sensor

LIGHT

Button

NUMBER OF TIMES GARAGE DOOR OPENER LIGHTS FLASH

1234

TIME THE GARAGE DOOR OPENER LIGHT STAYS ON

1 ½ Minutes 2 ½ Minutes 3 ½ Minutes 4 ½ Minutes

Operation

Command

LED

1 Press and release the Learn button on the garage

door opener. The Learn indicator light will glow

steadily for 30 seconds.

2 Within 30 seconds, press and hold

the button on the remote control.

3 Release the button when the

garage door opener light blinks.

It has learned the code. If light

bulbs are not installed, two

clicks will be heard.

PROGRAM A REMOTE USING THE LEARN BUTTON ON THE GARAGE DOOR OPENER

When replacing the light lens cover, ensure the antenna wires are hanging straight down.

Learn

Indicator

Light

Yellow

Learn

Button

Your garage door opener has been programmed at the factory to operate with your remote control. Older LiftMaster remote controls are NOT compatible. Programming can be done

through the door control or the Learn button on the garage door opener. To program additional remote controls refer to the instructions provided with the additional remote controls or visit

www.liftmaster.com. If your vehicle is equipped with a Homelink

, you may require an external adapter depending on the make, model, and year of your vehicle. Visit www.homelink.com for

additional information.

ERASE ALL REMOTE CONTROLS AND KEYLESS ENTRIES

1 Press and hold the learn button on garage door opener until the learn LED goes out

(approximately 6 seconds). All remote control and keyless entry codes are now erased.

Reprogram any accessory you wish to use.

ERASE ALL DEVICES (Including MyQ™ enabled accessories)

1 Press and hold the learn button on garage door opener until the learn LED goes out

(approximately 6 seconds).

2 Immediately press and hold the learn button again until the learn LED goes out. All codes

are now erased.

Reprogram any accessory you wish to use.

Programming - Remote Controls

Operation

To prevent possible SERIOUS INJURY or DEATH from a falling garage door:

• If possible, use emergency release handle to disengage trolley ONLY when garage

door is CLOSED. Weak or broken springs or unbalanced door could result in an open

door falling rapidly and/or unexpectedly.

• NEVER use emergency release handle unless garage doorway is clear of persons and

obstructions.

• NEVER use handle to pull door open or closed. If rope knot becomes untied, you

could fall.

DISCONNECT THE TROLLEY

1 The door should be fully closed if possible.

2 Pull down on the emergency release handle.

RECONNECT THE TROLLEY

The lockout feature prevents the trolley from reconnecting

automatically.

1 Pull the emergency release handle down and back (toward

the opener). The door can then be raised and lowered

manually as often as necessary.

2 To disengage the lockout feature, pull the handle straight

down.

The trolley will reconnect on the next UP or DOWN operation,

either manually or by using the door control or remote control.

To Open the Door Manually

Operation

Battery Backup (If applicable)

The battery backup system allows access in and out of your garage, even when the power is out. When the garage door opener is operating on battery power, the garage door opener will run

slower, the light will not function, the Battery Status LED will glow solid orange, and a beep will sound approximately every 2 seconds.

The battery charges when the garage door opener is plugged into a 110Vac electrical outlet that has power and requires 24 hours to fully charge. A fully charged battery supplies 12Vdc to

the garage door opener for one to two days of normal operation during an electrical power outage. After the electrical power has been restored, the battery will recharge within 24 hours. The

battery will last approximately 1 to 2 years with normal usage. Instructions for replacement are provided with the battery. To obtain maximum battery life and prevent damage, disconnect the

battery when the garage door opener is unplugged for an extended period of time.

NOTE: When the garage door opener is in battery backup mode the garage door opener lights, Timer-to-Close, and Remote Close features are unavailable.

BATTERY STATUS LED

GREEN LED:

All systems are normal.

• A solid green LED light indicates the

battery is fully charged.

• A ﬂ ashing green LED indicates the

battery is being charged.

ORANGE LED:

The garage door opener has lost power and

is in battery backup mode.

• A solid orange LED with beep, sounding

approximately every 2 seconds,

indicates the garage door opener is

operating on battery power.

• A ﬂ ashing orange LED with beep,

sounding every 30 seconds, indicates

the battery is low.

NOTE: The Battery Status LED is most

visible with the garage door opener light off.

Battery does not have to be fully charged to

operate the garage door opener.

Battery Status LED

RED LED:

The garage door opener’s 12V battery needs

to be replaced.

• A solid red LED with beep, sounding

every 30 seconds, indicates the garage

door opener needs servicing. Please

call for replacement battery to allow

your system to operate during a power

outage.

Adjustment

Introduction

Without a properly installed safety

reversal system, persons (particularly

small children) could be SERIOUSLY

INJURED or KILLED by a closing

garage door.

• Incorrect adjustment of garage door

travel limits will interfere with proper

operation of safety reversal system.

• After ANY adjustments are made,

the safety reversal system MUST

be tested. Door MUST reverse on

contact with 1-1/2" (3.8 cm) high

object (or 2x4 laid ﬂ at) on ﬂ oor.

To prevent damage to vehicles, be

sure fully open door provides adequate

clearance.

Your garage door opener is designed with

electronic controls to make setup and

adjustments easy. The adjustments allow

you to program where the door will stop in

the open (UP) and close (DOWN) position.

The electronic controls sense the amount of

force required to open and close the door.

NOTE: If anything interferes with the door’s

upward travel it will stop. If anything

interferes with the door’s downward travel,

it will reverse.

To watch a short instructional video on

programming your new garage door opener

use your smartphone to read the QR Code

below:

UP (Open)

DOWN (Close)

PROGRAMMING BUTTONS

The programming buttons are located on the

left side panel of the garage door opener and

are used to program the travel.

UP Button

Adjustment

Button

DOWN Button

PROGRAMMING BUTTONS

Program the Travel

Without a properly installed safety reversal system, persons (particularly small children) could be SERIOUSLY INJURED or KILLED by a

closing garage door.

• Incorrect adjustment of garage door travel limits will interfere with proper operation of safety reversal system.

• After ANY adjustments are made, the safety reversal system MUST be tested. Door MUST reverse on contact with 1-1/2" (3.8 cm)

high object (or 2x4 laid ﬂ at) on ﬂ oor.

1.1 Press and hold the Adjustment

Button until the UP Button begins

to ﬂ ash and/or a beep is heard.

1.5 Once the door is in the desired

DOWN position press and release

the Adjustment Button. The garage

door opener lights will ﬂ ash twice

and the UP Button will begin to

ﬂ ash.

1.2 Press and hold the UP Button

until the door is in the desired UP

position.

NOTE: The UP and DOWN Buttons can be used

to move the door up and down as needed.

1.6 Press and release the UP Button.

When the door travels to the

programmed UP position, the

DOWN Button will begin to ﬂ ash.

1.7 Press and release the DOWN

Button. The door will travel to the

programmed DOWN position.

Programming is complete.

1.4 Press and hold the DOWN Button

until the door is in the desired

DOWN position.

NOTE: The UP and DOWN Buttons can be used

to move the door up and down as needed.

* If the garage door opener lights are

ﬂ ashing 5 times during the steps for

Program the Travel, the programming

has timed out. If the garage door opener

lights are ﬂ ashing 10 times during the

steps for Program the Travel, the safety

reversing sensors are misaligned or

obstructed. When the sensors are aligned

and unobstructed, cycle the door through

a complete up and down cycle using the

remote control or the UP and DOWN

buttons. Programming is complete. If you

are unable to operate the door up and

down, repeat the steps for Programming

the Travel.

Adjustment

1.3 Once the door is in the desired

UP position press and release the

Adjustment Button. The garage

door opener lights will ﬂ ash twice

and the DOWN Button will begin

to ﬂ ash.

2.1 With the door fully open, place

a 1-1/2 inch (3.8 cm) board

(or a 2x4 laid ﬂ at) on the ﬂ oor,

centered under the garage door.

Test the Safety Reversal System

2.2 Press the remote control push

button to close the door. The door

MUST reverse when it makes

contact with the board.

If the door stops and does not reverse on

the obstruction, increase the down travel

(refer to Adjustment Step 1).

Repeat the test. When the door reverses

upon contact with the 1-1/2 inch board,

remove the board and open/close the door

3 or 4 times to test the adjustment.

If the test continues to fail, call a trained

door systems technician.

Without a properly installed safety

reversal system, persons (particularly

small children) could be SERIOUSLY

INJURED or KILLED by a closing

garage door.

• Safety reversal system MUST be

tested every month.

• After ANY adjustments are made,

the safety reversal system MUST

be tested. Door MUST reverse on

contact with 1-1/2" high (3.8 cm)

object (or 2x4 laid ﬂ at) on the ﬂ oor.

Test the Protector System

3.1 Open the door. Place the garage

door opener carton in the path

of the door.

The garage door opener will not close

from a remote control if the LED in either

safety reversing sensor is off (alerting you

to the fact that the sensor is misaligned or

obstructed).

If the garage door opener closes the

door when the safety reversing sensor is

obstructed (and the sensors are no more

than 6 inches [15 cm] above the ﬂ oor), call

for a trained door systems technician.

Without a properly installed safety

reversing sensor, persons (particularly

small children) could be SERIOUSLY

INJURED or KILLED by a closing

garage door.

3.2 Press the remote control push

button to close the door. The door

will not move more than an inch

(2.5 cm), and the garage door

opener lights will ﬂ ash 10 times.

Adjustment

To prevent possible SERIOUS INJURY or DEATH:

• NEVER allow small children near batteries.

• If battery is swallowed, immediately notify doctor.

To reduce risk of ﬁ re, explosion or chemical burn:

• Replace ONLY with 3V2032 coin batteries.

• DO NOT recharge, disassemble, heat above 212°F (100°C) or incinerate.

The Remote Control Battery

The lithium batteries should produce power

for up to 5 years. If the battery is low, the

remote control’s LED will not ﬂ ash when the

button is pressed. To replace battery, pry

open the case ﬁ rst in the middle (1), then at

each side (2 and 3) with the visor clip. Insert

battery positive side up.

Replace the batteries with only 3V2032

coin cell batteries. Dispose of old batteries

properly.

NOTICE: To comply with FCC and/or Industry Canada (IC) rules, adjustment or modiﬁ cations of this transceiver are

prohibited. THERE ARE NO USER SERVICEABLE PARTS. Any changes or modiﬁ cations not expressly approved by the

party responsible for compliance could void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC rules and IC RSS-210. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including

interference that may cause undesired operation.

This Class B digital apparatus complies with Canadian ICES-003.

AVIS : Les règles de la FCC et/ou d’Industrie Canada (IC) interdisent tout ajustement ou toute modiﬁ cation de ce

récepteur. IL N’EXISTE AUCUNE PIÈCE SUSCEPTIBLE D’ÊTRE ENTRETENUE PAR L’UTILISATEUR. Tout changement

ou toute modiﬁ cation non expressément approuvé par la partie responsable de la conformité peut avoir pour résultat

d’annuler l’autorité de l’utilisateur de faire fonctionner l’équipement.

Cet appareil est conforme aux dispositions de la partie 15 du règlement de la FCC et de la norme IC RSS-210. Son

utilisation est assujettie aux deux conditions suivantes : (1) ce dispositif ne peut causer des interférences nuisibles, et (2)

ce dispositif doit accepter toute interférence reçue, y compris une interférence pouvant causer un fonctionnement non

souhaité.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

Maintenance

EVERY MONTH

• Manually operate door. If it is unbalanced or binding, call a trained door systems

technician.

• Check to be sure door opens and closes fully. Adjust if necessary, see page 10.

• Test the safety reversal system. Adjust if necessary, see page 11.

EVERY YEAR

• Oil door rollers, bearings and hinges. The garage door opener does not require additional

lubrication. Do not grease the door tracks.

• (If applicable) Test the battery backup and consider replacing the battery to ensure the

garage door opener will operate during an electrical power outage.

Testing the Battery Backup:

1. Unplug the garage door opener. The battery status LED will either glow solid orange

indicating opener is operating on battery power or will ﬂ ash indicating low battery

power.

2. Open and close the door using the remote control or door control.

NOTE: The garage door opener may run slower if the battery is not fully charged.

The battery will take 24 hours to fully charge.

3. Plug in the garage door opener. Verify the battery status LED is ﬂ ashing green,

indicating the battery is charging.

EVERY TWO TO THREE YEARS

• Use a rag to wipe away the existing grease from the garage door opener rail. Reapply a

small layer of white lithium grease to the top and underside of the rail surface where the

trolley slides.

DIAGNOSTIC CODE SYMPTOM SOLUTION

Up arrow

Flash(es)

Down arrow

Flash(es)

The garage door opener will not close and the light

bulbs ﬂ ash.

Safety sensors are not installed, connected, or wires may be cut. Inspect sensor wires for a

disconnected or cut wire.

The garage door opener will not close and the light

bulbs ﬂ ash.

There is a short or reversed wire for the safety sensors. Inspect safety sensor wire at all

staple and connection points, replace wire or correct as needed.

The door control will not function. The wires for the door control are shorted or the door control is faulty. Inspect door control

wires at all staple and connection points, replace wire or correct as needed.

The garage door opener will not close and the light

bulbs ﬂ ash.

Safety sensors are misaligned or were momentarily obstructed. Realign both sensors to

ensure both LEDs are steady and not ﬂ ickering. Make sure nothing is hanging or mounted on

the door that would interrupt the sensor’s path while closing.

Door moves 6-8" stops or reverses. Manually open and close the door. Check for binding or obstructions, such as a broken

spring or door lock, correct as needed. Check wiring connections at travel module and at the

logic board. Replace travel module if necessary.

No movement, only a single click. Manually open and close the door. Check for binding or obstructions, such as a broken

spring or door lock, correct as needed. Replace logic board if necessary.

Opener hums for 1-2 seconds no movement. Manually open and close the door. Check for binding or obstructions, such as a broken

spring or door lock, correct as needed. Replace motor if necessary.

Door coasts after it has come to a complete stop. Program travel to coasting position or have door balanced by a trained door systems

technician.

2 1-5

No movement, or sound. Replace logic board.

Unable to set the travel or retain position. Check travel module for proper assembly, replace if necessary.

The battery status LED* is constantly ﬂ ashing

green.

Battery backup* charging circuit error, replace the logic board.

*If applicable.

Troubleshooting

Diagnostic Chart

Your garage door opener is programmed with self-diagnostic capabilities. The UP and DOWN arrows on the garage door opener will ﬂ ash the diagnostic codes.

Troubleshooting

Diagnostic Chart

My garage door opener beeps:

The garage door opener can beep for several reasons:

• Garage door opener has been activated through a device or feature such as Timer-to-Close,

garage door monitor or LiftMaster Internet Gateway, see page 4.

• Operating on battery power or the 12Vdc battery needs to be replaced (if applicable), see

page 7 and 11.

My remote control will not activate the garage door:

• Verify the lock feature is not activated on the door control.

• Reprogram the remote control.

• If the remote control will still not activate the door check the diagnostic codes to ensure the

garage door opener is working properly.

My door will not close and the light bulbs blink on my motor unit:

The safety reversing sensor must be connected and aligned correctly before the garage door

opener will move in the down direction.

• Verify the safety sensors are properly installed, aligned and free of any obstructions.

DIAGNOSTIC CODE SYMPTOM SOLUTION

Up arrow

Flash(es)

Down arrow

Flash(es)

4 1-4

Door is moving stops or reverses. Manually open and close the door. Check for binding or obstructions, such as a broken spring

or door lock, correct as needed. If the door is binding or sticking contact a trained door

systems technician. If door is not binding or sticking attempt to reprogram travel (refer to

page 10).

Opener runs approximately 6-8", stops and reverses. Communication error to travel module. Check travel module connections, replace travel

module if necessary.

The garage door opener will not close and the light

bulbs ﬂ ash.

Safety sensors are misaligned or were momentarily obstructed. Realign both sensors to

ensure both LEDs are steady and not ﬂ ickering. Make sure nothing is hanging or mounted on

the door that would interrupt the sensor’s path while closing.

My garage door opener light(s) will not turn off when the door is open:

The garage door opener is equipped with a feature that turns the light on when the safety

reversing sensors have been obstructed or when the motion sensor on the door control

detects movement in the garage. These features can be disabled using the door control, see

page 6.

My neighbor’s remote control opens my garage door:

Erase the memory from your garage door opener and reprogram the remote control(s).

My vehicle’s Homelink

is not programming to my garage door opener:

Depending on the make, model, and year of your vehicle an external adapter may be required.

Visit www.homelink.com for additional information.

Repair Parts

4B & 4C

NOTE: For additional parts not shown, visit www.liftmaster.com to download or print

the full owner’s manual.

DESCRIPTION

PART

NUMBER

Light Lens 41A7562

Receiver Logic Board - Model 8350 & 8360 45DCT

Receiver Logic Board - Model 8355 & 8365 45ACT

Travel Module - Model 8350 & 8360 41A7114-7

Travel Module - Model 8355 & 8365 41D7742-7

Motor w/Travel Module - Model 8350 & 8360

41D1739-1

Motor w/Travel Module - Model 8355 41D7442

Motor w/Travel Module - Model 8365 41D7440

3V2032 Lithium Battery (Remote Control) 10A20

Backup Battery (if applicable) 485LM

Safety Sensor Kit with receiving and sending

sensors with 3 feet (.9 m) 2-conductor wire 41A5034

LIFTMASTER

ONE YEAR LIMITED WARRANTY

LIFETIME MOTOR AND BELT* LIMITED WARRANTY

ONE YEAR LIMITED WARRANTY FOR THE BATTERY BACKUP SYSTEM*

The Chamberlain Group, Inc. (“Seller”) warrants to the first retail purchaser of this product, for the residence in which this product is originally installed, that it is free from defects in

materials and/or workmanship for a period of one year from the date of purchase, except that the motor and belt* are warranted to be free from defects in materials and/or

workmanship for the lifetime of the product while you own your residence, and the Battery Backup System* is warranted to be free from defects in materials and/or workmanship for

a period of one year from the date of purchase. The proper operation of this product is dependent on your compliance with the instructions regarding installation, operation, and

maintenance and testing. Failure to comply strictly with those instructions will void this limited warranty in its entirety.

If, during the limited warranty period, this product appears to contain a defect covered by this limited warranty, call 1-800-528-9131, toll free, before dismantling this product. You

will be advised of disassembly and shipping instructions when you call. Then send the product or component, pre-paid and insured, as directed to our service center for warranty

repair. Please include a brief description of the problem and a dated proof-of-purchase receipt with any product returned for warranty repair. Products returned to Seller for warranty

repair, which upon receipt by Seller are confirmed to be defective and covered by this limited warranty, will be repaired or replaced (at Seller’s sole option) at no cost to you and

returned pre- paid. Defective parts will be repaired or replaced with new or factory-rebuilt parts at Seller’s sole option. [You are responsible for any costs incurred in removing and/or

reinstalling the product or any component.]

ALL IMPLIED WARRANTIES FOR THE PRODUCT, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR

PURPOSE, ARE LIMITED IN DURATION TO THE APPLICABLE LIMITED WARRANTY PERIOD SET FORTH ABOVE FOR THE RELATED COMPONENT(S), AND NO IMPLIED

WARRANTIES WILL EXIST OR APPLY AFTER SUCH PERIOD. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply

to you. THIS LIMITED WARRANTY DOES NOT COVER NON-DEFECT DAMAGE, DAMAGE CAUSED BY IMPROPER INSTALLATION, OPERATION OR CARE (INCLUDING, BUT NOT

LIMITED TO ABUSE, MISUSE, FAILURE TO PROVIDE REASONABLE AND NECESSARY MAINTENANCE, UNAUTHORIZED REPAIRS OR ANY ALTERATIONS TO THIS PRODUCT),

LABOR CHARGES FOR REINSTALLING A REPAIRED OR REPLACED UNIT, REPLACEMENT OF CONSUMABLE ITEMS (E.G., BATTERIES IN REMOTE CONTROL TRANSMITTERS

AND LIGHT BULBS), OR UNITS INSTALLED FOR NON-RESIDENTIAL USE. THIS LIMITED WARRANTY DOES NOT COVER ANY PROBLEMS WITH, OR RELATING TO, THE GARAGE

DOOR OR GARAGE DOOR HARDWARE, INCLUDING BUT NOT LIMITED TO THE DOOR SPRINGS, DOOR ROLLERS, DOOR ALIGNMENT OR HINGES. THIS LIMITED WARRANTY

ALSO DOES NOT COVER ANY PROBLEMS CAUSED BY INTERFERENCE. UNDER NO CIRCUMSTANCES SHALL SELLER BE LIABLE FOR CONSEQUENTIAL, INCIDENTAL OR

SPECIAL DAMAGES ARISING IN CONNECTION WITH USE, OR INABILITY TO USE, THIS PRODUCT. IN NO EVENT SHALL SELLER’S LIABILITY FOR BREACH OF WARRANTY,

BREACH OF CONTRACT, NEGLIGENCE OR STRICT LIABILITY EXCEED THE COST OF THE PRODUCT COVERED HEREBY. NO PERSON IS AUTHORIZED TO ASSUME FOR US ANY

OTHER LIABILITY IN CONNECTION WITH THE SALE OF THIS PRODUCT.

Some states do not allow the exclusion or limitation of consequential, incidental or special damages, so the above limitation or exclusion may not apply to you. This limited warranty

gives you specific legal rights, and you may also have other rights, which vary from state to state.

*If applicable.

Warranty

The Chamberlain Group, Inc.

845 Larch Avenue

Elmhurst, Illinois 60126-1196

www.liftmaster.com

MATIÈRES

Importantes Consignes de Sécurité ......... 2-3

Fonctionnement ...................................4

Utilisation de la commande de porte .......5

Programmation - Panneau de

commande de porte ............................6

Programmation - Télécommande ............7

Pour effacer tous le codes ....................7

Ouverture manuelle de la porte ..............8

Pile de secours* ................................8

Réglage ............................................9

Programmation des courses ................ 10

Essai du système d’inversion

de sécurité .................................... 11

Essai du Protector System

................. 11

Entretien.......................................... 12

Dépannage ................................... 13-14

Pièces de Rechange ............................ 15

Garantie .......................................... 16

Ouvre-porte de garage

de série PREMIUM

■ Veuillez lire attentivement ce guide de même que la documentation de

sécurité incluse.

■ La porte NE SE FERMERA PAS si le Système Protector

n’est pas branché et

réglé correctement.

■ Des vérifications périodiques de l’ouvre-porte de garage sont requises pour

garantir un fonctionnement sécuritaire du dispositif.

■ Cet ouvre-porte de garage est compatible UNIQUEMENT avec les accessoires

MyQ™ et Security✚ 2.0™.

■ N’activez PAS la fonction de minuterie de fermeture si vous installez l’ouvre-

porte de garage sur une porte rigide. La minuterie de fermeture doit être utilisée

UNIQUEMENT sur les portes articulées.

■ Apposer les étiquettes d’avertissement incluses à l’endroit indiqué sur l’étiquette.

Numéro de série :

Date d’achat :

Guide de l’utilisateur

POUR RÉSIDENCES SEULEMENT

Veuillez noter les renseignements suivants

pour référence ultérieure :

L’INFORMATION DE CONTACT

Laissez ce Guide de l’utilisateur au propriétaire.

Les illustrations de ce mode d’emploi ne servent qu’à titre de référence. Votre appareil peut avoir un aspect différent.

*S’il y a lieu.

Revue des symboles de

sécurité et des mots de

signalement

Cet ouvre-porte de garage a été conçu et mis

à l’essai dans le but d’offrir un service sûr à

condition qu’il soit installé, utilisé, entretenu

et mis à l’essai en stricte conformité avec les

instructions et les avertissements contenus dans

le présent manuel.

Lorsque vous verrez ces symboles de sécurité et

ces mots de signalement sur les pages suivantes,

ils vous aviseront de la possibilité de blessures

graves ou de mort si vous ne vous conformez

pas aux avertissements qui les accompagnent.

Le danger peut être de source mécanique ou

provenir d’un choc électrique. Lisez attentivement

les avertissements.

Mécanique

Électrique

ATTENTION

AVERTISSEMENTAVERTISSEMENT AVERTISSEMENT

AVERTISSEMENT

ATTENTION

AVERTISSEMENT AVERTISSEMENTAVERTISSEMENT

AVERTISSEMENT

ATTENTION

ATTENTIONATTENTION

AVERTISSEMENT AVERTISSEMENT

AVERTISSEMENT

Lorsque vous verrez ce mot de signalement

sur les pages suivantes, il vous avisera de la

possibilité de dommages à votre porte de garage

ou ouvre-porte de garage, ou les deux, si vous

ne vous conformez pas aux énoncés de mise en

garde qui l’accompagnent. Lisez-les attentivement.

IMPORTANTES INSTRUCTIONS CONCERNANT LA POSE

Pour réduire le risque de BLESSURES GRAVES, voire

MORTELLES :

AVERTISSEMENTAVERTISSEMENT

1. LIRE ET SUIVRE TOUS LES AVERTISSEMENTS ET INSTRUCTIONS.

2. Poser l’ouvre-porte de garage UNIQUEMENT sur une porte de

garage bien équilibrée et lubriﬁ ée. Une porte mal équilibrée peut

ne PAS inverser sa course en cas de besoin et peut entraîner des

BLESSURES GRAVES, voire MORTELLES.

3. TOUTES les réparations aux câbles, ensembles de ressort et autres

ferrures de montage DOIVENT être conﬁ ées à un technicien formé en

systèmes de porte AVANT de poser l’ouvre-porte.

4. Désactiver TOUTES les serrures et retirer TOUTES les cordes

raccordées à la porte de garage AVANT de poser l’ouvre-porte aﬁ n

d’éviter un emmêlement.

5. Poser l’ouvre-porte de garage à au moins 2,13 m (7 pi) au-dessus du

sol.

6. Laisser le déverrouillage de secours à portée de main, mais à au

moins 1,83 m (6 pi) du sol et éviter tout contact avec des véhicules

aﬁ n d’éviter tout déclenchement accidentel.

7. Ne JAMAIS raccorder l’ouvre-porte de garage à une source de

courant avant d’avoir reçu l’instruction de le faire.

8. Ne JAMAIS porter de montres, bagues ou vêtements amples durant

la pose ou l’entretien de l’ouvre-porte. Ils pourraient être happés par

la porte de garage ou les mécanismes de l’ouvre-porte.

9. Poser la commande de porte murale :

• bien en vue de la porte de garage.

• hors de la portée des enfants à une hauteur minimum de 5 pieds

(1,5 m).

• à l’écart de TOUTES les pièces mobiles de la porte.

10. Placer l’étiquette d’avertissement de prise au piège sur le mur à côté de

la commande de la porte de garage.

11. Placer l’étiquette d’essai d’inversion de sécurité/ouverture manuelle

bien en vue sur le côté intérieur de la porte de garage.

12. Au terme de la pose, faire l’essai du système d’inversion de sécurité.

La porte DOIT remonter au contact d’un objet d’une hauteur de 1-1/2

po (3,8 cm) (ou un 2 x 4 posé à plat) sur le sol.

13. Pour éviter des BLESSURES GRAVES ou la MORT par électrocution,

débranchez TOUTE alimentation électrique ainsi que les piles AVANT

TOUTE intervention.

14. N’activez PAS la minuterie de fermeture si vous utilisez une porte de

garage monobloc ou battante. Elle doit être activée UNIQUEMENT

lorsqu’on utilise une porte articulée.

15.

CONSERVER CES

INSTRUCTIONS.

Importantes Consignes de Sécurité

REMARQUE : Pour des instructions d’installation complètes, allez sur le site www.liftmaster.com pour imprimer en entier le Manuel d’instructions.

IMPORTANTES CONSIGNES DE SÉCURITÉ

Pour réduire le risque de BLESSURES GRAVES, voire

MORTELLES :

AVERTISSEMENT

1. LIRE ET SUIVRE TOUS LES AVERTISSEMENTS ET INSTRUCTIONS.

2. Gardez EN TOUT TEMPS la télécommande hors de portée des enfants.

Ne JAMAIS laisser les enfants faire fonctionner les télécommandes ou

les boutonspoussoirs de la commande de porte ou jouer avec ceux-ci.

3. Actionner la porte de garage UNIQUEMENT lorsqu’on peut la voir

clairement, qu’elle est bien réglée et qu’il n’y a aucune obstacle à la

course de la porte.

4. Gardez TOUJOURS la porte de garage en vue TOUTE personne ou

tout objet à l’écart de la porte jusqu’à sa fermeture complète. NE

LAISSEZ PERSONNE TRAVERSER LA TRAJECTOIRE DE LA PORTE EN

MOUVEMENT.

5. PERSONNE NE DOIT PASSER SOUS UNE PORTE ARRÊTÉE OU

PARTIELLEMENT OUVERTE.

6. Si possible, utilisez la poignée de déclenchement d’urgence pour

dégager le chariot UNIQUEMENT lorsque la porte de garage est

FERMÉE. Faites preuve de prudence lorsque vous utilisez cette poignée

lorsque la porte est ouverte. Des ressorts affaiblis ou brisés ou une

porte déséquilibrée peuvent entraîner la chute rapide et/ou inattendue

de la porte et accroître le risque de BLESSURES GRAVES, voire

MORTELLES.

7. N’utilisez JAMAIS la poignée de déclenchement d’urgence à moins que

rien ou personne n’obstrue la trajectoire de la porte.

8. N’utilisez JAMAIS la poignée pour ouvrir ou fermer la porte de garage. Il

y a risque de chute si le noeud de la corde se défait.

9. Après avoir effectué quelque réglage que ce soit, on DOIT faire l’essai

du système d’inversion de sécurité.

10. Le système d’inversion de sécurité DOIT être testé chaque mois. La porte

de garage DOIT remonter au contact d’un objet d’une hauteur de 3,8 cm

(1-1/2 po) (ou un 2 x 4 posé à plat) du sol. À défaut de régler l’ouvre-

porte de garage correctement, le risque de BLESSURE GRAVE ou de

MORT ACCIDENTELLE sera accru.

11. LA PORTE DE GARAGE DOIT TOUJOURS ÊTRE CORRECTEMENT

ÉQUILIBRÉE. Une porte mal équilibrée peut ne PAS inverser sa course

en cas de besoin et peut entraîner des BLESSURES GRAVES, voire

MORTELLES.

12. TOUTES les réparations sur les câbles, les ressorts et la quincaillerie,

et de TOUT ce qui se trouve sous une tension EXTRÊME, DOIVENT être

conﬁ ées à des techniciens formés à cet effet.

13. TOUJOURS mettre l’ouvre-porte de garage hors tension AVANT

d’effectuer quelque réparation que ce soit ou d’enlever des couvercles.

14. Ce système opérateur est équipé d’un dispositif de fonctionnement

sans surveillance. La porte est susceptible de se mettre en mouvement

inopinément. NE LAISSEZ PERSONNE TRAVERSER LA TRAJECTOIRE DE

LA PORTE EN MOUVEMENT.

15. N’activez PAS la minuterie de fermeture si vous utilisez une porte de

garage monobloc ou battante. Elle doit être activée UNIQUEMENT

lorsqu’on utilise une porte articulée.

16.

CONSERVER CES

INSTRUCTIONS.

Importantes Consignes de Sécurité

Votre porte de garage est dotée de fonctions qui vous offrent un meilleur contrôle du fonctionnement de

votre porte de garage. Les accessoires fournis avec votre ouvre-porte de garage peuvent varier selon le

modèle acheté.

ALERT2CLOSE (ALERTE DE FERMETURE)

La fonction d’alerte de fermeture fournit une alerte visuelle et audible vous avertissant de la fermeture

d’une porte non surveillée.

MINUTERIE DE FERMETURE (TTC)

La minuterie de fermeture ferme automatiquement la porte après une période déterminée qu’on peut régler

en utilisant la commande de porte avec TTC (Modele 881LM ou 880LM). Avant et pendant la fermeture de

la porte, l’ouvre-porte de garage émet des bips et l’éclairage se met à clignoter.

MyQ™

La technologie MyQ™ utilise un signal de 900 MHz pour fournir une communication bidirectionnelle entre

l’ouvre-porte de garage et les accessoires MyQ™. Votre porte de garage est compatible avec un maximum

de 16 accessoires MyQ™.

TÉLÉCOMMANDES ET COMMANDES DE PORTE (SECURITY✚

2.0™)

L’ouvre-porte de garage a été programmé en usine de manière à fonctionner avec la télécommande, qui

change à chaque utilisation, accédant au hasard à plus de 100 milliards de nouveaux codes. Compatible

avec les accessoires MyQ™ et Security✚ 2.0™.

REMARQUE : Les anciens telecommandes, commandes de porte LiftMaster, et les produits de tiers ne son

pas compatibles.

Accessories (Security✚ 2.0™)

CAPACITÉ DE MISE EN MÉMOIRE

Télécommandes

Jusqu’à 24

Commande de la porte

Jusqu’à 2 panneaux Smart Control ou 4 commandes de

portes Security✚ 2.0™

Ouvre-porte sans ﬁ l et sans clé

Jusqu’à 2

THE PROTECTOR SYSTEM

(CAPTEURS D’INVERSION DE SÉCURITÉ)

Lorsqu’il est bien connecté et bien aligné, le capteur d’inversion détectera un obstacle sur le passage de

son faisceau infrarouge. Si un obstacle brise le faisceau infrarouge pendant que la porte se ferme, la porte

s’arrêtera et remontera jusqu’à la position entièrement ouverte et les lumières de l’ouvre-porte clignoteront

10 fois. Si la porte est complètement ouverte et que les capteurs d’inversion ne sont pas installés ou sont

mal alignés, la porte ne se ferme pas à partir d’une télécommande. Cependant, vous pouvez fermer la

porte si vous maintenez le bouton de la commande de porte ou la commande de télédéverrouillage jusqu’à

ce que la porte soit totalement fermée. Le capteur d’inversion n’a aucun effet sur le cycle d’ouverture.

CONSERVATION DE L’ÉNERGIE

Pour une efﬁ cacité énergétique, l’ouvre-porte de garage se met en mode de veille lorsque la porte est

complètement fermée. Le mode de veille ferme l’ouvre-porte de garage jusqu’à ce qu’il soit activé. Le

mode veille est séquencé à l’ampoule d’éclairage de l’ouvre-porte de garage; lorsque l’ampoule s’éteint, le

témoin DEL du capteur s’éteint et chaque fois que l’éclairage de l’ouvre-porte de garage s’allume, le témoin

DEL du capteur s’allume.

ÉCLAIRAGE

Les ampoules de l’ouvre-porte de garage s’allument lorsque ce dernier est initialement branchée au

courant; l’alimentation est rétablie, âpres un interruption ou lorsque l’ouvre-porte de garage est active.

Les lumières s’eteindront automatiquement âpres 4-1/2 minutes. Une ampoule à incandescence A19 (100

watts, au maximum) ou, pour une efﬁ cacité énergétique maximale, une lampe ﬂ ourescente compacte de

26 W (équivalant à 100 W).

Fonction D’Éclairage

L’ouvre-porte de garage est dote d’une fonction supplément; l’eclairage s’allume lorsque quelqu’un entre

part la porte de garage ouverte et que le faisceau infrarouge du capteur inverseur de sécurité est rompu.

Pour un contrôle supplémentaire de ampoules de votre ouvre-porte de garage, reporte-vous le page 6.

UTILISATION DE VOTRE OUVRE-PORTE DE GARAGE

L’ouvre-porte de garage peut être activé par le biais d’une commande de porte murale, une télécommande,

une commande de télédéverrouillage ou un accessoire MyQ™. Lorsque la porte est fermée et que l’ouvre-

porte de garage est activé, la porte s’ouvrira. Si la porte détecte un obstacle ou est interrompue lors

de son ouverture, elle s’arrêtera. Si le porte n’est pas fermée et que l’ouvre-porte de garage est activé,

elle fermer. Si l’ouvre-porte de garage détecte un obstacle pendant la fermeture, la porte inversera sa

course. L’obstacle interrompt le faisceau du détecteur, les lumières de l’ouvre-porte clignoteront pendant

10 secondes. Cependant, vous pouvez fermer la porte si vous maintenez le bouton de la commande de

porte ou la commande de télédéverrouillage jusqu’à ce que la porte soit totalement fermée. Le capteur

d’inversion n’a aucun effet sur le cycle d’ouverture. Le détecteur inverseur de sécurité doit être connecté et

aligné correctement avant que l’ouvre-porte de garage n’entame le mouvement de fermeture.

Fonctionnement

La page charge ...

LeftMaster HBW7675 Manuel utilisateur

Marque: LeftMaster

Modèle: HBW7675

Catégorie: Porte de garage

Taper: Manuel utilisateur

Ce manuel convient également à

PREMIUM Series Garage Door Opener

Télécharger le PDF

rapport

dans d''autres langues

English: LeftMaster HBW7675 User manual

LeftMaster HBW7675 Manuel utilisateur

Ce manuel convient également à

LeftMaster HBW7675 Manuel utilisateur

dans d''autres langues

Autres documents