Riccar Prima Straight Suction Manuel utilisateur

Owner’s Manual

R50SS, R50FSN

& R50TAP

CONTENTS

Getting Started

Important Safety Instructions

2

Polarization Instructions

3

Description of the Vacuum and Standard Accessories

4

Assembling the Vacuum

Attaching the Hose to the Vacuum

5

Attaching the Wand to the Hose

5

Attaching the Tool Caddy to the Hose

5

Operation

Motor Speed Control

6

Carrying the Vacuum

6

Power Cord Management

6

Storage

6

Attachment Cleaning

Cleaning Tools

7

Adjusting the Suction Power

8

Wand Cleaning

8

Tools Adaptor

8

Maintenance and Care

When to Change the Vacuum Bag/Full Bag Indicator

9

Replacing the Vacuum Bag

9

When to Change the Filters

10

Replacing the HEPA Media Filter

10

Replacing the Secondary Filter

10

Power Cord Care

11

Annual Checkup

11

Power Nozzle Operation and Maintenance

Tandem Air Power Nozzle

12-15

Full Size Power Nozzle

16-20

Problem Solving Guide

Troubleshooting

21

Visit Riccar Vacuums Online

21

How to Contact Your Authorized Retailer

21

Key Replacement Parts

21

For Best Performance

21

Warranty

22

2

IMPORTANT SAFETY INSTRUCTIONS

When using an electrical appliance, basic precautions

should always be followed, including the following:

READ ALL INSTRUCTIONS BEFORE USING THIS

APPLIANCE. FOR HOUSEHOLD USE ONLY.

IMPORTANT:

The manufacturer cannot accept responsibility for damage

caused when the appliance is not used according to the

instructions, or for uses other than those for which it was intended.

WARNING:

To reduce the risk of fire, electric shock, damage or injury:

• Do not leave appliance when plugged

in. Unplug from outlet when not in use

and before servicing.

• WARNING: ELECTRIC SHOCK COULD

OCCUR IF USED OUTDOORS OR ON

WET SURFACES. This vacuum is intended

for household use only.

• Do not allow to be used as a toy. Close

attention is necessary when used by or

near children or when used near pets.

Do not use on pets.

• Use only as described in this manual.

Use only manufacturer’s recommended

attachments.

• Do not use with damaged cord or plug.

If appliance is not working as it should,

has been dropped, damaged, left outdoors,

or dropped into water, return it to your

Authorized Retailer for service.

• Do not pull or carry by cord, use cord

as a handle, close a door on the cord,

or pull cord around sharp edges or

corners. Do not run appliance over cord.

Keep cord away from heated surfaces.

• Do not unplug by pulling on cord. To

unplug, grasp the plug, not the cord.

• Hold plug when retracting the power

cord to prevent the cord from whipping.

• Do not handle plug or appliance with

wet hands.

• Do not put any object into openings.

Do not use with any opening blocked;

keep free of dust, lint, hair and anything

that may reduce air flow.

• Keep hair, loose clothing, fingers and

all parts of body away from openings

and moving parts.

• Do not pick up anything that is burning

or smoking, such as cigarettes, matches

or hot ashes.

• Do not use without vacuum bag in place.

• Turn off all controls before unplugging.

• Use extra care when cleaning on stairs.

• Do not use to pick up flammable or

combustible liquids such as gasoline or

use in areas where they may be present.

• Do not attempt to service the unit while

appliance is plugged in.

• Do not use vacuum to pick up water or

any wet materials.

SAVE THESE INSTRUCTIONS

3

Power Cord, 2-Wire Polarized Cord

To reduce the risk of electric shock, the charger is equipped with a polarized

alternating current line plug (a plug having one blade wider than the other). This

plug will fit into the power outlet only one way. This is a safety feature. If you are

unable to insert the plug fully into the outlet, try reversing the plug. If the plug

should still fail to fit, contact a qualified electrician to replace the obsolete outlet.

Do not defeat the safety purpose of the polarized plug.

AUTO POLARIZATION INSTRUCTIONS

4

14

16

1

2

3

4

5

6

7

8

9

10

11

17

12

13

15

14

1 On/Off Switch

2 Motor Speed Control

3 Full Bag Indicator

4 Bag Compartment Latch

5 Tool Caddy

6 2-n-1 Tool

7 Crevice Tool

8 Suction Relief Dial

9 Handle Release Button

10 Wand Extension Button

11 Telescopic Wand

12 Microfiber Bare Floor Tool

13 Tool Adapter

14 Wand and Floor Tool Storage (2)

15 Power Cord Catch

16 Carry Handle

17 Floor Turbo Nozzle (R50SS Model)

DESCRIPTION OF THE VACUUM AND

STANDARD ACCESSORIES

5

ASSEMBLING THE VACUUM

Attaching the Hose to the Vacuum

NOTE: Do not plug in the vacuum until

it is completely assembled.

Push the hose inlet into the canister body

until it clicks into place. (Fig. 1)

To remove the hose from the canister

body, press the buttons on the hose inlet

and pull it away from the canister (Fig. 1).

Attaching the Wand to the Hose

Push the hose handle into the top of the

wand until it clicks into place (Fig. 2).

Attaching the Tool Caddy to

the Hose

Attach the tool caddy to the hose by

lifting up on the tool clip and sliding

the tool caddy down until it clicks into

place. Attach any of the cleaning tools

to the caddy (Fig. 3).

Fig 1.

Fig. 2

Fig. 3

6

OPERATION

Motor Speed Control

Slide to increase or decrease the power

of the motor (Fig. 1).

Carrying the Vacuum

To safely transport your vacuum,

especially when carrying the vacuum

up and down stairs, use the Carry

Handle located at the top of the bag

compartment (Fig. 2).

Power Cord Management

Pull the cord out of the vacuum to the

desired length. Do not pull the cord out

past the yellow safety tape.

Insert the cord into the cord catch to

lock it into place (Fig. 3).

To retract the cord, remove it from the

cord catch and tug on the cord until it

retracts into the vacuum.

Storage

The tab on the end of the wand or the

neck of the floor tool can be inserted

into either groove on the back or on the

bottom of the canister for easy storage

(Fig. 4).

Fig. 4

Fig. 2

Fig. 3

Fig. 1

7

Fig. 3

ATTACHMENT CLEANING

Fig. 1

Insert here for

Dusting Brush

Insert here for

Upholstery Tool

Cleaning Tools

Your vacuum is equipped with a 2-n-1

(dusting brush/upholstery) tool, crevice

tool and microfiber floortool.

Attach any of the cleaning tools to the end

of the telescopic wand or the hose handle.

2-n-1 Tool

Convert from a dusting brush to an

upholstery tool by inserting the hose

handle or wand end into the indicated

openings (Fig. 1).

Crevice Tool

Ideal for tight places like between seat

cushions or corners (Fig. 2).

Microfiber Bare Floor Tool

Cleans and polishes tile, hard wood and

linoleum floors (Fig. 3)

Fur Get It Pet Hair Remover Tool

(R50TAP Model)

Ideal for removing pet hair from

upholstery and vehicles (Fig. 4).

Floor Turbo Nozzle (R50SS Model)

Cleans area rugs and low pile carpet.

Suction relief slider adjusts the suction

level (Fig. 5).

Fig. 2

Fig. 4 Fig. 5

8

ATTACHMENT CLEANING

Fig. 1

Adjusting the Suction Power for

Tool Cleaning

Full suction power may be too strong

for some cleaning situations. For example,

reduced suction power would be appropriate

for cleaning sheer curtains.

On the hose handle, locate the Suction

Relief Dial and rotate it open. This reduces

the suction power coming through the hose.

Rotate the dial closed (Fig. 1) when finished

to restore full suction power.

Wand Cleaning

Extend the wand by pushing the wand

extension button and pushing the wand outward

to the desired length (Fig. 2).

Disconnect the wand from the hose handle

by pressing the Handle Release Button (Fig. 3).

Tools Adapter

Attach the adapter to the end of the wand

to use other cleaning tools not included with

this vacuum (Fig. 4).

Fig. 2

Fig. 4

Fig. 3

9

MAINTENANCE AND CARE

When to Change the Vacuum Bag

The Full Bag Indicator changes to red to

show when the bag is full or when there

is a clog in the vacuum (Fig. 1).

The indicator could also turn red when

vacuuming fine powders such as flour or

drywall dust. These materials can quickly

block the bag pores, significantly reducing

airflow before the bag is actually full.

The vacuum bag should still be changed.

The indicator may also turn red during

attachment cleaning. If the indicator

changes to green when attachments are

no longer in use, the vacuum bag does

not need to be changed.

NOTE: The vacuum bags are disposable

and should be used once. Do not attempt

to reuse the bag, as suction and filtration

performance will be greatly reduced.

Replacing the Vacuum Bag

Change the vacuum bag when the full

bag indicator changes from green to red

or when the suction power is weak.

• Open the bag compartment lid (Fig. 2).

• Pull the tab on the bag collar, which

closes the bag while removing it from

the bag holder.

• Remove and discard the used bag.

• Slide a new bag into the bag holder

until it clicks into place.

• Close the bag compartment lid.

Fig. 1

Fig. 2

10

MAINTENANCE AND CARE

When to Change the Filters

It’s recommended to replace the HEPA

media and secondary filters after using

12 vacuum bags.

If someone in your household suffers

from allergies, it is recommended to

change the filter set after every six

vacuumbags.

Replacing the HEPA Media Filter

Open the bag compartment lid and locate

the filter behind the vacuum bag. For

better access to the HEPA media filter,

remove the bag.

Grasp the tab with two fingers and pull

the filter out toward you. Replace with

a new filter by sliding the filter in and

pushing down on the top of the tab until

it clicks into place (Fig. 1).

Replacing the Secondary Filter

• Open the bag compartment lid and

locate the filter behind the vacuum bag.

For better access to the secondary filter,

remove the bag.

• Pull the filter cartridge up out of the

vacuum and discard (Fig. 2).

• Slide a new filter cartridge back into

place and replace the bag.

NOTE: Filters cannot be

washed and reused.

Fig. 1

Fig. 2

11

MAINTENANCE AND CARE

Power Cord Care

• If the cord or plug has any apparent damage, refrain from using the vacuum.

Please visit an Authorized Riccar Vacuum Retailer for a new cord or plug.

• When the vacuum is in use, hold the cord to keep from running over it.

• Avoid obstructions and do not pull the cord around sharp edges or corners.

• Always keep the cord away from heated surfaces and never close doors on it as

this may cause damage to the wiring.

• To unplug, always grasp the plug, not the cord.

Annual Checkup

To keep your vacuum in peak operating condition, it is recommended you bring your

vacuum to an Authorized Riccar Vacuum Retailer for an annual checkup. The retailer will

conduct a comprehensive examination to ensure your vacuum is in top operating condition.

12

DESCRIPTION OF THE TANDEM AIR

POWER NOZZLE

Rear ViewFront View

2

3

5

6

8

10

9

1 Handle

2 On/Off Control for Power Nozzle

3 Handle Release Button

4 Telescopic Wand

5 Wand Extension Button

6 Wand Release Button

7 Tandem Air Power Nozzle

8 Headlight

8 Jammed Brushroll Warning Lights

9 Soft Furniture Guard

10 Handle Release Button

1

4

7

13

OPERATION OF THE TANDEM AIR POWER NOZZLE

Turning On the Power Nozzle

The power nozzle can only be turned

on if the canister is also turned on. The

canister On/Off switch is located on

the main body. The power nozzle On/Off

switch is located on the handle. Simply

press the switch forward to engage the

power nozzle.

Reclining the Wand

Press the Handle Release Pedal located

on the back of the vacuum with your foot

to recline the handle (Fig. 1).

Removing and Inserting the Wand

Removing the wand from the power

nozzle allows you to use cleaning tools

for baseboard or ceiling cleaning. To

do this, first turn the power nozzle and

canister off. Then, press the wand release

button, pull the wand out and turn the

canister on (Fig. 2).

To reinsert the wand into the power nozzle,

turn off the canister and simply press the

wand back into the neck of the power

nozzle. The wand will then click into place.

Jammed Brushroll Warning Lights

This power nozzle is equipped with

a safety system that protects it from

a jammed situation. Items that cause

jammed brushrolls include socks,

excessive threads and corners of area

rugs. The warning indicator lights in the

headlight lens will change to flashing red

should this condition occur(Fig. 3).

• Turn off the vacuum cleaner and the

power nozzle then unplug the power cord.

• Remove the object preventing the

brushroll from turning.

When the unit is turned back on, the red

warning indicator lights in the headlight

lens will be off if the jam has been

successfully removed.

MATERIAL

DRAWN

ISSUED

SCALE

FINISH

DATE

DO NOT SCALE

UNLESS OTHERWISE SPECIFIED

DESCRIPTION

DRAWING SIZE:C

PART NUMBER

SHEET 3 OF 8

TACONY CORPORATION CLAIMS PROPRIETARY

RIGHTS IN THE MATERIAL DISCLOSED HERE IN.

THIS DRAWING IS ISSUED FOR ENGINEERING

INFORMATION ONLY. IT MAY NOT BE REPRO-

DUCED, NOR MAY THE INFORMATION HERE IN

BE USED FOR MANUFACTURING PURPOSES

WITHOUT WRITTEN PERMISSION FROM TACONY

CORPORATION.

0.250

TACONY CORPORATION

1760 Gilsinn Lane, Fenton, MO 63026

DESCRIPTION OF CHANGE

REV

PART NUMBER

SHEET

3 OF 8

X.X .5 mm RADII X.X .5mm

X.XX .25mm X.XX .25mm

X.XXX .12mm MACHINE SURFACE

X.XXXX .012mm BREAK SHARP CORNERS TO .25mm MAX

0 30" COMMON TO BE CONCETRIC TO .05mm

BYECN NODATEREV

Fig. 1

Fig. 2

Fig. 3

14

MAINTENANCE OF THE TANDEM AIR

POWER NOZZLE

Fig. 2

MATERIAL

DRAWN

ISSUED

SCALE

FINISH

DATE

DO NOT SCALE

UNLESS OTHERWISE SPECIFIED

DESCRIPTION

DRAWING SIZE:C

PART NUMBER

SHEET 8 OF 8

TACONY CORPORATION CLAIMS PROPRIETARY

RIGHTS IN THE MATERIAL DISCLOSED HERE IN.

THIS DRAWING IS ISSUED FOR ENGINEERING

INFORMATION ONLY. IT MAY NOT BE REPRO-

DUCED, NOR MAY THE INFORMATION HERE IN

BE USED FOR MANUFACTURING PURPOSES

WITHOUT WRITTEN PERMISSION FROM TACONY

CORPORATION.

0.250

TACONY CORPORATION

1760 Gilsinn Lane, Fenton, MO 63026

DESCRIPTION OF CHANGE

REV

PART NUMBER

SHEET

8 OF 8

X.X .5 mm RADII X.X .5mm

X.XX .25mm X.XX .25mm

X.XXX .12mm MACHINE SURFACE

X.XXXX .012mm BREAK SHARP CORNERS TO .25mm MAX

0 30" COMMON TO BE CONCETRIC TO .05mm

BYECN NODATEREV

SCALE 0.400

Fig. 1

MATERIAL

DRAWN

ISSUED

SCALE

FINISH

DATE

DO NOT SCALE

UNLESS OTHERWISE SPECIFIED

DESCRIPTION

DRAWING SIZE:C

PART NUMBER

SHEET 8 OF 8

TACONY CORPORATION CLAIMS PROPRIETARY

RIGHTS IN THE MATERIAL DISCLOSED HERE IN.

THIS DRAWING IS ISSUED FOR ENGINEERING

INFORMATION ONLY. IT MAY NOT BE REPRO-

DUCED, NOR MAY THE INFORMATION HERE IN

BE USED FOR MANUFACTURING PURPOSES

WITHOUT WRITTEN PERMISSION FROM TACONY

CORPORATION.

0.250

TACONY CORPORATION

1760 Gilsinn Lane, Fenton, MO 63026

DESCRIPTION OF CHANGE

REV

PART NUMBER

SHEET

8 OF 8

X.X .5 mm RADII X.X .5mm

X.XX .25mm X.XX .25mm

X.XXX .12mm MACHINE SURFACE

X.XXXX .012mm BREAK SHARP CORNERS TO .25mm MAX

0 30" COMMON TO BE CONCETRIC TO .05mm

BYECN NODATEREV

SCALE 0.400

Edge Cleaning

The edge cleaning feature provides improved

cleaning near walls and stationary furniture.

For maximum edge cleaning, place the

left side of the nozzle, from the user’s

perspective, against the wall.

Automatic Carpet Height

Adjustment

Your vacuum is designed with an automatic

self-adjusting nozzle. No manual adjustments

are required. The height of the nozzle

automatically adjusts to the flooring surface.

This self-adjusting feature allows the nozzle

to float evenly over all flooring surfaces.

Replacing the Vacuum Belt

WARNING! To Reduce the Risk of Electrical

Shock or Injury from Moving Parts, Turn

the Vacuum Off and Unplug it.

NOTE: To ensure maximum cleaning

efficiency, the belt should be checked

regularly to be sure it is in good condition.

Check to see if the belt is stretched, cracked,

or if excessive slipping is occurring. Replace

if needed.

• Turn the vacuum off and unplug it

before changing the belt.

• Remove the bottom plate (see Removing

the BottomPlate, page 15).

• Remove the brushroll and the worn

or broken belt from the brushroll pulley

and the motor drive shaft(Fig. 1).

• Loop the new belt around the motor

drive shaft and the brushroll.

• Reinstall the brushroll into the nozzle.

Turn the brushroll by hand, making

sure the belt is not twisted and all

rotating parts move smoothly(Fig.2).

• Reinstall the bottom plate (see Replacing

the BottomPlate, page 15).

15

MAINTENANCE OF THE TANDEM AIR

POWER NOZZLE

Replacing the Squeegee

WARNING! To Reduce the Risk of

Electrical Shock or Injury from Moving

Parts, Turn the Vacuum Off and Unplugit.

This power nozzle is equipped with a

squeegee on the bottom to improve its

effectiveness in cleaning bare floors.

If the squeegee splits or begins to look

worn, simply slide the worn squeegee

from its track and slide a new one into

the track (Fig. 1). If you have trouble

installing the new squeegee, contact

an Authorized Riccar Retailer for

furtherassistance.

Removing the BottomPlate

Turn the power nozzle over. Turn the two

screws 1/4 turn (Fig. 2) to release the

bottom plate. Lift off the bottom plate.

Replacing the BottomPlate

Line up the hinges on the bottom plate

then press the plate into position. Replace

the two screws and turn 1/4 turn to tighten.

MATERIAL

DRAWN

ISSUED

SCALE

FINISH

DATE

DO NOT SCALE

UNLESS OTHERWISE SPECIFIED

DESCRIPTION

DRAWING SIZE:C

PART NUMBER

SHEET 8 OF 8

TACONY CORPORATION CLAIMS PROPRIETARY

RIGHTS IN THE MATERIAL DISCLOSED HERE IN.

THIS DRAWING IS ISSUED FOR ENGINEERING

INFORMATION ONLY. IT MAY NOT BE REPRO-

DUCED, NOR MAY THE INFORMATION HERE IN

BE USED FOR MANUFACTURING PURPOSES

WITHOUT WRITTEN PERMISSION FROM TACONY

CORPORATION.

0.250

TACONY CORPORATION

1760 Gilsinn Lane, Fenton, MO 63026

DESCRIPTION OF CHANGE

REV

PART NUMBER

SHEET

8 OF 8

X.X .5 mm RADII X.X .5mm

X.XX .25mm X.XX .25mm

X.XXX .12mm MACHINE SURFACE

X.XXXX .012mm BREAK SHARP CORNERS TO .25mm MAX

0 30" COMMON TO BE CONCETRIC TO .05mm

BYECN NODATEREV

SCALE 0.400

Fig. 2

MATERIAL

DRAWN

ISSUED

SCALE

FINISH

DATE

DO NOT SCALE

UNLESS OTHERWISE SPECIFIED

DESCRIPTION

DRAWING SIZE:C

PART NUMBER

SHEET 4 OF 8

TACONY CORPORATION CLAIMS PROPRIETARY

RIGHTS IN THE MATERIAL DISCLOSED HERE IN.

THIS DRAWING IS ISSUED FOR ENGINEERING

INFORMATION ONLY. IT MAY NOT BE REPRO-

DUCED, NOR MAY THE INFORMATION HERE IN

BE USED FOR MANUFACTURING PURPOSES

WITHOUT WRITTEN PERMISSION FROM TACONY

CORPORATION.

0.250

TACONY CORPORATION

1760 Gilsinn Lane, Fenton, MO 63026

DESCRIPTION OF CHANGE

REV

PART NUMBER

SHEET

4 OF 8

X.X .5 mm RADII X.X .5mm

X.XX .25mm X.XX .25mm

X.XXX .12mm MACHINE SURFACE

X.XXXX .012mm BREAK SHARP CORNERS TO .25mm MAX

0 30" COMMON TO BE CONCETRIC TO .05mm

BYECN NODATEREV

Fig. 1

16

DESCRIPTION OF THE FULL SIZE POWER NOZZLE

Rear ViewFront View

2

3

5

8

7

9 11

12

10

6

4

1

1 Handle

2 On/Off Control for Power Nozzle

3 Handle Release Button

4 Telescopic Wand

5 Wand Extension Button

6 Wand Release Collar

7 Jammed Brushroll Warning Light

8 Height Indicator Window

9 Headlight

10 Soft Furniture Guard

11 Handle Release Pedal

12 Height Adjustment Pedal

17

OPERATION OF THE FULL SIZE POWER NOZZLE

Fig. 3

Turning On the Power Nozzle

The power nozzle can only be turned on

if the canister is also turned on. The canister’s

On/Off switch is located on the main body.

The power nozzle On/Off switch is located

on the handle. Simply press the switch

forward to engage the power nozzle.

Reclining the Wand

After turning on the canister and the

power nozzle, lower the wand by pressing

the left pedal on the back side of the

power nozzle (Fig. 1).

Removing and Inserting

the Wand

Remove the wand from the power nozzle

to use cleaning tools. Turn the power

nozzle and the canister off. Then, press

the wand release collar and remove the

wand and turn the canister on (Fig. 2).

To reinsert the wand into the power nozzle,

turn the canister off and press the wand

back into the neck of the power nozzle.

The wand will then click into place.

Carpet Height Adjustment

This power nozzle has six different

settings to clean a variety of carpet

types and floor surfaces. To adjust

the carpet height setting of the power

nozzle, press the right pedal located on

the back of the power nozzle (Fig.3).

Each press of this pedal will adjust the

height to the next carpet height position.

The height indicator window shows the

current setting. You will see one of the six

settings detailed below (Fig. 4).

Setting: Intended Use:

1. XHI Very plush carpet

2. HI Plush carpet

3. Auto General carpet thickness

or bare floors

4. MED Medium pile carpet

5. LO Low pile carpet

6. XLO Indoor/Outdoor carpet

Fig. 1

Fig. 2

Fig. 4

18

OPERATION OF THE FULL SIZE POWER NOZZLE

Carpet Height Adjustment Tips:

When using the power nozzle, start on

the “Auto” setting. If pushing the power

nozzle feels difficult, then adjust to a

higher setting. If the power nozzle feels

very easy to push, you may want to lower

the power nozzle for more effective cleaning.

The “Auto” setting is the recommended

setting for hard floor surfaces (i.e. tile,

vinyl, wood).

Warning Light

Your power nozzle is equipped with a

circuit breaker safety system that protects

it from a jammed situation. Items that

cause jammed brushrolls include socks,

excessive threads and corners of area

rugs. The warning indicator light on top

of the unit will change from green to red

should this condition occur (Fig. 1).

If the circuit breaker trips:

• Turn off the vacuum cleaner and power

nozzle then unplug the power cord.

• Remove the object preventing the

brushroll from turning.

• Locate the circuit breaker switch on

the back of the power nozzle and

press it to reset the breaker (Fig. 2).

When the unit is turned back on, the

warning light should be green.

If the breaker trips again, repeat these

steps again to correct the problem If

this does not correct the problem, contact

an Authorized Riccar Retailer for

further assistance.

Fig. 2

Fig. 1

La page charge ...

Riccar Prima Straight Suction Manuel utilisateur

Ce manuel convient également à

Riccar Prima Straight Suction Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents