Sony DSX-A200UI Mode d'emploi

Marque: Sony

Modèle: DSX-A200UI

Catégorie: Récepteurs multimédia de voiture

Taper: Mode d'emploi

4-576-780-42(2)

DSX-A200UI

FM/AM

Digital Media

Player

Owner’s Record

The model and serial numbers are located on the bottom of the unit.

Record the serial number in the space provided below.

Refer to these numbers whenever you call upon your Sony dealer

regarding this product.

Model No. DSX-A200UI

Serial No.

Operating Instructions

Mode d’emploi

To cancel the demonstration (DEMO) display, see page 12.

For the connection/installation, see page 20.

Pour annuler l’affichage de démonstration (DEMO),

reportez-vous à la page 12.

Pour le raccordement/l’installation, reportez-vous à la page 21.

2GB

The nameplate indicating operating voltage, etc., is

located on the bottom of the chassis.

Warning

For safety, be sure to install this unit in the

dashboard of the car as the rear side of the unit

becomes hot during use.

For details, see “Connection/Installation”

(page 20).

FOR THE CUSTOMERS IN THE USA. NOT

APPLICABLE IN CANADA, INCLUDING IN THE

PROVINCE OF QUEBEC.

POUR LES CLIENTS AUX ÉTATS-UNIS. NON

APPLICABLE AU CANADA, Y COMPRIS LA

PROVINCE DE QUÉBEC.

This equipment has been tested and found to

comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable

protection against harmful interference in a

residential installation. This equipment

generates, uses, and can radiate radio frequency

energy and, if not installed and used in

accordance with the instructions, may cause

harmful interference to radio communications.

However, there is no guarantee that interference

will not occur in a particular installation. If this

equipment does cause harmful interference to

radio or television reception, which can be

determined by turning the equipment off and

on, the user is encouraged to try to correct the

interference by one or more of the following

measures:

 Reorient or relocate the receiving antenna.

 Increase the separation between the

equipment and receiver.

 Connect the equipment into an outlet on a

circuit different from that to which the receiver

is connected.

 Consult the dealer or an experienced radio/TV

technician for help.

You are cautioned that any changes or

modifications not expressly approved in this

manual could void your authority to operate this

equipment.

3GB

For the State of California, USA only

Perchlorate Material – special handling may apply,

See

www.dtsc.ca.gov/hazardouswaste/perchlorate

WARNING: Do not ingest battery,

Chemical Burn Hazard.

The remote commander contains a coin/

button cell battery. If the coin/button cell battery is

swallowed, it can cause severe internal burns in just

2 hours and can lead to death.

Keep new and used batteries away from children. If

the battery compartment does not close securely,

stop using the product and keep it away from

children.

If you think batteries might have been swallowed or

placed inside any part of the body, seek immediate

medical attention.

Note on the lithium battery

Do not expose the battery to excessive heat such as

direct sunlight, fire or the like.

Disclaimer regarding services offered by

third parties

Services offered by third parties may be changed,

suspended, or terminated without prior notice.

Sony does not bear any responsibility in these sorts

of situations.

Warning if your car’s ignition has no ACC

position

Be sure to set the AUTO OFF function (page 13).

The unit will shut off completely and

automatically in the set time after the unit is

turned off, which prevents battery drain. If you

do not set the AUTO OFF function, press and hold

OFF until the display disappears each time you

turn the ignition off.

4GB

Table of Contents

Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Guide to Parts and Controls . . . . . . . . . . . . . . . . . . . 5

Getting Started

Detaching the Front Panel . . . . . . . . . . . . . . . . . . . . 7

Setting the Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Connecting a USB Device . . . . . . . . . . . . . . . . . . . . . 8

Connecting Other Portable Audio Device . . . . . . . . 8

Listening to the Radio

Listening to the Radio. . . . . . . . . . . . . . . . . . . . . . . . 9

Using Radio Data System (RDS) . . . . . . . . . . . . . . . . 9

Playback

Playing a USB Device . . . . . . . . . . . . . . . . . . . . . . . 10

Searching and Playing Tracks. . . . . . . . . . . . . . . . . 10

Listening to Pandora®

Setting up Pandora® . . . . . . . . . . . . . . . . . . . . . . . . 11

Streaming Pandora® . . . . . . . . . . . . . . . . . . . . . . . . 11

Available Operations in Pandora® . . . . . . . . . . . . . 12

Settings

Canceling the DEMO Mode . . . . . . . . . . . . . . . . . . 12

Basic Setting Operation . . . . . . . . . . . . . . . . . . . . . 12

General Setup (GENERAL). . . . . . . . . . . . . . . . . . . . 13

Sound Setup (SOUND) . . . . . . . . . . . . . . . . . . . . . . 13

Display Setup (DISPLAY) . . . . . . . . . . . . . . . . . . . . . 13

Additional Information

Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Connection/Installation

Cautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Parts List for Installation . . . . . . . . . . . . . . . . . . . . 20

Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

5GB

Guide to Parts and Controls

 Front panel release button

 SRC (source)

Turn on the power.

Change the source.

OFF

Press and hold for 1 second to turn the source

off and display the clock.

Press and hold for more than 2 seconds to turn

off the power and the display.

If the unit is turned off and the display

disappears, operation by the remote

commander is not available.

 Control dial

Rotate to adjust the volume.

PUSH ENTER

Enter the selected item.

Open the setup menu.

 Display window

 SEEK +/–

Tune in radio stations automatically. Press and

hold to tune manually.

/ (prev/next)

/ (fast-reverse/fast-forward)

 PTY (program type)

Select PTY in RDS.

(browse) (page 10, 11, 12)

Enter the browse mode during playback.

 MODE (page 9, 10, 12)

(back)

Return to the previous display.

 Receptor for the remote commander

Main unit

6GB

 Number buttons (1 to 6)

Receive stored radio stations. Press and hold to

store stations.

ALBUM /

Skip an album for audio device. Press and hold

to skip albums continuously.

Press  to thumbs up, or  to thumbs down in

Pandora® (page 12).

(repeat)

(shuffle)

PAUSE

 MEGA BASS

Reinforces bass sound in synchronization with

the volume level. Press to change the MEGA

BASS setting: [1], [2], [OFF].

 AUX input jack

 DSPL (display)

Press to change display items.

SCRL (scroll)

Press and hold to scroll a display item.

 USB port

The VOL (volume) + button has a tactile dot.

 ATT (attenuate)

Attenuate the sound. Press again to cancel the

attenuation.

 SOUND

Open the SOUND menu directly.

Press and hold to open the setup menu.

///

Select a setup item, etc.

ENTER

Enter the selected item.

/ (prev/next)

+/– (album +/–)

 VOL (volume) +/–

RM-X211 Remote commander

7GB

Remove the insulation film before use.

Detaching the Front Panel

You can detach the front panel of this unit to

prevent theft.

1 Press and hold OFF  until the unit turns

off, press the front panel release button

, then pull the panel towards you to

remove.

Caution alarm

If you turn the ignition switch to the OFF position

without detaching the front panel, the caution

alarm will sound for a few seconds. The alarm will

only sound if the built-in amplifier is used.

Getting Started

Attaching the front panel

8GB

Setting the Clock

1 Press MENU, rotate the control dial to

select [SET GENERAL], then press it.

2 Rotate the control dial to select [SET

CLOCK-ADJ], then press it.

The hour indication flashes.

3 Rotate the control dial to set the hour

and minute.

To move the digital indication, press SEEK +/–.

4 After setting the minute, press MENU.

The setup is complete and the clock starts.

To display the clock

Press DSPL.

Connecting a USB Device

1 Turn down the volume on the unit.

2 Connect the USB device to the unit.

To connect an iPod/iPhone, use the USB

connection cable for iPod (not supplied).

Connecting Other Portable

Audio Device

1 Turn off the portable audio device.

2 Turn down the volume on the unit.

3 Connect the portable audio device to the

AUX input jack (stereo mini jack) on the

unit with a connecting cord (not

supplied)*.

* Be sure to use a straight type plug.

4 Press SRC to select [AUX].

To match the volume level of the connected

device to other sources

Start playback of the portable audio device at a

moderate volume, and set your usual listening

volume on the unit.

Press MENU, then select [SET SOUND]  [SET AUX

VOL] (page 13).

9GB

Listening to the Radio

To listen to the radio, press SRC to select [TUNER].

1 Press MODE to change the band (FM1,

FM2, FM3, AM1 or AM2).

2 Press MENU, rotate the control dial to

select [SET GENERAL], then press it.

3 Rotate the control dial to select [SET

BTM], then press it.

The unit stores stations in order of frequency on

the number buttons.

1 Press MODE to change the band (FM1,

FM2, FM3, AM1 or AM2).

2 Perform tuning.

To tune manually

Press and hold SEEK +/– to locate the

approximate frequency, then press SEEK +/–

repeatedly to fine adjust to the desired

frequency.

To tune automatically

Press SEEK +/–.

Scanning stops when the unit receives a station.

1 While receiving the station that you want

to store, press and hold a number button

(1 to 6) until [MEM] appears.

1 Select the band, then press a number

button (1 to 6).

Using Radio Data System (RDS)

1 Press PTY during FM reception.

2 Rotate the control dial until the desired

program type appears, then press it.

The unit starts to search for a station

broadcasting the selected program type.

Type of programs

The CT data from the RDS transmission sets the

clock.

1 Set [SET CT-ON] in [SET GENERAL]

(page 13).

Listening to the Radio

Storing automatically (BTM)

Tuning

Storing manually

Receiving the stored stations

Selecting program types (PTY)

NEWS (News), INFORM (Information), SPORTS

(Sports), TALK (Talk), ROCK (Rock), CLS ROCK

(Classic Rock), ADLT HIT (Adult Hits), SOFT RCK (Soft

Rock), TOP 40 (Top 40), COUNTRY (Country),

OLDIES (Oldies), SOFT (Soft), NOSTALGA

(Nostalgia), JAZZ (Jazz), CLASSICL (Classical),

R & B (Rhythm and Blues), SOFT R&B (Soft Rhythm

and Blues), LANGUAGE (Foreign Language), REL

MUSC (Religious Music), REL TALK (Religious Talk),

PERSNLTY (Personality), PUBLIC (Public), COLLEGE

(College), HABL ESP (Spanish Talk), MUSC ESP

(Spanish Music), HIP HOP (Hip-Hop), WEATHER

(Weather)

Setting clock time (CT)

10GB

Playing a USB Device

In these Operating Instructions, “iPod” is used as a

general reference for the iPod functions on an iPod

and iPhone, unless otherwise specified by the text

or illustrations.

For details on the compatibility of your iPod, see

“About iPod” (page 14) or visit the support site on

the back cover.

MSC (Mass Storage Class) and MTP (Media Transfer

Protocol) type USB devices (such as a USB flash

drive, digital media player, Android smartphone)

compliant with the USB standard can be used.

Depending on the digital media player or Android

smartphone, setting the USB connection mode to

MTP is required.

Notes

 For details on the compatibility of your USB device,

visit the support site on the back cover.

 Playback of the following files is not supported.

MP3/WMA/FLAC:

 copyright-protected files

 DRM (Digital Rights Management) files

 Multi-channel audio files

MP3/WMA:

 lossless compression files

1 Connect a USB device to the USB port

(page 8).

Playback starts.

If a device is already connected, to start

playback, press SRC to select [USB] ([IPD]

appears in the display when the iPod is

recognized).

2 Adjust the volume on this unit.

To stop playback

Press and hold OFF for 1 second.

To remove the device

Stop playback, then remove the device.

Caution for iPhone

When you connect an iPhone via USB, phone call

volume is controlled by the iPhone, not the unit. Do

not inadvertently increase the volume on the unit

during a call, as a sudden loud sound may result

when the call ends.

1 During playback, press and hold MODE

until [MODE IPOD] appears.

Operations of the iPod become available.

Note that the volume can be adjusted only by

the unit.

To exit passenger control

Press and hold MODE until [MODE AUDIO] appears.

Searching and Playing Tracks

1 During playback, press (repeat) or

(shuffle) repeatedly to select the desired

play mode.

Playback in the selected play mode may take

time to start.

Available play modes differ depending on the

selected sound source.

1 During USB playback, press (browse)*

to display the list of search categories.

When the track list appears, press (back)

repeatedly to display the desired search

category.

* During USB playback, press (browse) for more

than 2 seconds to directly return to the beginning

of the category list.

Playback

Operating an iPod directly (Passenger

control)

Repeat play and shuffle play

Searching a track by name (Quick-

BrowZer™)

11GB

2 Rotate the control dial to select the

desired search category, then press it to

confirm.

3 Repeat step 2 to search the desired track.

Playback starts.

To exit the Quick-BrowZer mode

Press (browse).

1 Press (browse).

2 Press SEEK +.

3 Rotate the control dial to select the item.

The list is jumped in steps of 10% of the total

number of items.

4 Press ENTER to return to the Quick-

BrowZer mode.

The selected item appears.

5 Rotate the control dial to select the

desired item, then press it.

Playback starts.

Pandora® is available to stream music through your

iPhone. You can control Pandora® on a USB-

connected iPhone from this unit.

Pandora® is only available in certain countries.

Please visit

http://www.pandora.com/legal

for more information.

Setting up Pandora®

1 Check the compatibility of your mobile

device by visiting the support site on the

back cover.

2 Download the latest version of the

Pandora® application from your

smartphone’s app store. A list of

compatible devices can be found at

www.pandora.com/everywhere/mobile

Streaming Pandora®

1 Connect the iPhone to this unit (page 8).

2 Press SRC to select [PANDORA USB].

3 Launch Pandora® application on your

mobile device.

4 Press PAUSE to start playback.

Searching by skipping items

(Jump mode)

Listening to Pandora®

12GB

Available Operations in

Pandora®

“Thumbs Up” or “Thumbs Down” feedback allows

you to personalize stations.

1 During playback, press  (Thumbs Up) or

 (Thumbs Down).

The station list allows you to easily select a desired

station.

1 During playback, press (browse).

2 Press SEEK + to select the sorting order

[BY DATE] or [A TO Z].

3 Rotate the control dial to select the

desired station, then press it.

Playback starts.

The track currently being played can be

bookmarked and stored in your Pandora® account.

1 During playback, press MODE.

Canceling the DEMO Mode

You can cancel the demonstration display which

appears when the source is off and the clock is

displayed.

1 Press MENU, rotate the control dial to

select [SET GENERAL], then press it.

2 Rotate the control dial to select [SET

DEMO], then press it.

3 Rotate the control dial to select [SET

DEMO-OFF], then press it.

The setting is complete.

4 Press (back) twice.

The display returns to normal reception/play

mode.

Basic Setting Operation

You can set items in the following setup categories:

General setup (GENERAL), Sound setup (SOUND),

Display setup (DISPLAY)

1 Press MENU.

2 Rotate the control dial to select the setup

category, then press it.

The items that can be set differ depending on

the source and settings.

3 Rotate the control dial to select the

options, then press it.

To return to the previous display

Press (back).

“Thumbs” feedback

Using the station list

Bookmarking

Settings

13GB

General Setup (GENERAL)

DEMO (demonstration)

Activates the demonstration: [ON], [OFF].

CLOCK-ADJ (clock adjust) (page 8)

CAUT ALM (caution alarm)

Activates the caution alarm: [ON], [OFF] (page 7).

(Available only while the source is off and the

clock is displayed.)

BEEP

Activates the beep sound: [ON], [OFF].

AUTO OFF

Shuts off automatically after a desired time

when the unit is turned off: [NO], [30S] (30

seconds), [30M] (30 minutes), [60M] (60

minutes).

CT (clock time)

Activates the CT function: [ON], [OFF].

BTM (best tuning memory) (page 9)

(Available only when the tuner is selected.)

Sound Setup (SOUND)

This setup menu is available when any source

except for the BT phone is selected.

EQ5 PRESET

Selects an equalizer curve from 10 equalizer

curves or off: [OFF], [R&B], [ROCK], [POP],

[DANCE], [HIP-HOP], [ELECTRONICA], [JAZZ],

[SOUL], [COUNTRY], [CUSTOM].

The equalizer curve setting can be memorized

for each source.

EQ5 SETTING

Sets [CUSTOM] of EQ5.

BASE

Selects a preset equalizer curve as a basis for

further customizing: [BAND1] (low frequency),

[BAND2] (mid-low frequency), [BAND3] (mid

frequency), [BAND4] (mid-high frequency),

[BAND5] (high frequency).

The volume level is adjustable in 1 dB steps,

from -10 dB to +10 dB.

BALANCE

Adjusts the sound balance: [RIGHT-15] –

[CENTER] – [LEFT-15].

FADER

Adjusts the relative level: [FRONT-15] – [CENTER]

– [REAR-15].

AUX VOL (AUX volume level)

Adjusts the volume level for each connected

auxiliary device: [+18 dB] – [0 dB] – [-8 dB].

This setting negates the need to adjust the

volume level between sources.

Display Setup (DISPLAY)

DIMMER

Changes the display brightness: [ON], [OFF].

SND SYNC (sound synchronization)

Activates the synchronization of the illumination

with the sound: [ON], [OFF].

AUTO SCR (auto scroll)

Scrolls long items automatically: [ON], [OFF].

(Not available when the AUX or tuner is

selected.)

14GB

Precautions

 Cool off the unit beforehand if your car has been

parked in direct sunlight.

 Do not leave the front panel or audio devices

brought in inside the car, or it may cause

malfunction due to high temperature in direct

sunlight.

 Power antenna (aerial) extends automatically.

To maintain high sound quality

Do not splash liquid onto the unit.

 You can connect to the following iPod models.

Update your iPod devices to the latest software

before use.

Compatible iPhone/iPod models

 “Made for iPod,” and “Made for iPhone,” mean

that an electronic accessory has been designed to

connect specifically to iPod or iPhone,

respectively, and has been certified by the

developer to meet Apple performance standards.

Apple is not responsible for the operation of this

device or its compliance with safety and

regulatory standards. Please note that the use of

this accessory with iPod or iPhone may affect

wireless performance.

Additional Information

Playback order of audio files

Folder (album)

Audio file (track)

About iPod

Compatible Model USB

iPhone 6 Plus 

iPhone 6 

iPhone 5s 

iPhone 5c 

iPhone 5 

iPhone 4s 

iPhone 4 

iPhone 3GS 

iPod touch

(5th generation)



iPod touch

(4th generation)



iPod touch

(3rd generation)



iPod classic 

iPod nano

(7th generation)



iPod nano

(6th generation)



iPod nano

(5th generation)



15GB

If you have any questions or problems concerning

your unit that are not covered in this manual,

consult your nearest Sony dealer.

Maintenance

Replacing the lithium battery of the remote

commander

Under normal conditions, the battery will last

approximately 1 year. (The service life may be

shorter, depending on the conditions of use.)

When the battery becomes weak, the range of the

remote commander becomes shorter.

CAUTION

Danger of explosion if battery is incorrectly

replaced. Replaced only with the same or

equivalent type.

Notes on the lithium battery

 Keep the lithium battery out of the reach of children.

Should the battery be swallowed, immediately

consult a doctor.

 Wipe the battery with a dry cloth to ensure a good

contact.

 Be sure to observe the correct polarity when installing

the battery.

 Do not hold the battery with metallic tweezers,

otherwise a short-circuit may occur.

Cleaning the connectors

The unit may not function properly if the

connectors between the unit and the front panel

are not clean. In order to prevent this, detach the

front panel (page 7) and clean the connectors with

a cotton swab. Do not apply too much force.

Otherwise, the connectors may be damaged.

Notes

 For safety, turn off the ignition before cleaning the

connectors, and remove the key from the ignition

switch.

 Never touch the connectors directly with your fingers

or with any metal device.

Specifications

FOR THE CUSTOMERS IN THE USA. NOT

APPLICABLE IN CANADA, INCLUDING IN THE

PROVINCE OF QUEBEC.

POUR LES CLIENTS AUX ÉTATS-UNIS. NON

APPLICABLE AU CANADA, Y COMPRIS LA

PROVINCE DE QUÉBEC.

AUDIO POWER SPECIFICATIONS

CEA2006 Standard

Power Output: 17 Watts RMS × 4 at 4

Ohms < 1% THD+N

SN Ratio: 80 dBA

(reference: 1 Watt into 4 Ohms)

Tuner section

Tuning range: 87.5 – 107.9 MHz

Antenna (aerial) terminal:

External antenna (aerial) connector

Intermediate frequency:

FM CCIR: -1,956.5 to -487.3 kHz and

+500.0 to +2,095.4 kHz

Usable sensitivity: 7 dBf

Selectivity: 75 dB at 400 kHz

Signal-to-noise ratio: 73 dB

Separation: 50 dB at 1 kHz

Frequency response: 20 – 15,000 Hz

Tuning range: 530 – 1,710 kHz

+ side up

16GB

Antenna (aerial) terminal:

External antenna (aerial) connector

Sensitivity: 26 μV

USB Player section

Interface: USB (Full-speed)

Maximum current: 1 A

The maximum number of recognizable tracks:

 folders (albums): 256

 files (tracks) per folder: 256

Corresponding codec:

MP3 (.mp3)

Bit rate: 8 – 320 kbps (Supports VBR (Variable

Bit Rate))

Sampling rate: 16 – 48 kHz

WMA (.wma)

Bit rate: 32 – 192 kbps (Supports VBR (Variable

Bit Rate))

Sampling rate: 32 kHz, 44.1 kHz, 48 kHz

FLAC (.flac)

Bit depth: 16 bit, 24 bit

Sampling rate: 44.1 kHz, 48 kHz

Power amplifier section

Output: Speaker outputs

Speaker impedance: 4 – 8 ohms

Maximum power output: 55 W × 4 (at 4 ohms)

General

Outputs:

Audio outputs terminal (rear)

Power antenna (aerial)/Power amplifier control

terminal (REM OUT)

Inputs:

Remote controller input terminal

Antenna (aerial) input terminal

AUX input jack (stereo mini jack)

USB port

Power requirements: 12 V DC car battery (negative

ground (earth))

Rated current consumption: 10 A

Dimensions:

Approx. 178 mm × 50 mm × 120 mm

/8 in × 2 in × 4

/4 in) (w/h/d)

Mounting dimensions:

Approx. 182 mm × 53 mm × 102 mm

/4 in × 2

/8 in × 4

/8 in) (w/h/d)

Mass: Approx. 0.7 kg (1 lb 9 oz)

Package contents:

Main unit (1)

Remote commander (1): RM-X211

Parts for installation and connections (1 set)

Your dealer may not handle some of the above

listed accessories. Please ask the dealer for detailed

information.

Design and specifications are subject to change

without notice.

Windows Media is either a registered trademark or

trademark of Microsoft Corporation in the United

States and/or other countries.

This product is protected by certain intellectual

property rights of Microsoft Corporation. Use or

distribution of such technology outside of this

product is prohibited without a license from

Microsoft or an authorized Microsoft subsidiary.

iPhone, iPod, iPod classic, iPod nano, iPod touch,

and Siri are trademarks of Apple Inc., registered in

the U.S. and other countries.

MPEG Layer-3 audio coding technology and patents

licensed from Fraunhofer IIS and Thomson.

Pandora®, the Pandora® logo, and the Pandora®

trade dress are trademarks or registered

trademarks of Pandora Media, Inc., used with

permission.

Android is a trademark of Google Inc.

libFLAC

Redistribution and use in source and binary forms,

with or without modification, are permitted

provided that the following conditions are met:

 Redistributions of source code must retain the

above copyright notice, this list of conditions and

the following disclaimer.

Copyrights

17GB

 Redistributions in binary form must reproduce

the above copyright notice, this list of conditions

and the following disclaimer in the

documentation and/or other materials provided

with the distribution.

 Neither the name of the Xiph.org Foundation nor

the names of its contributors may be used to

endorse or promote products derived from this

software without specific prior written

permission.

THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT

HOLDERS AND CONTRIBUTORS “AS IS” AND ANY

EXPRESS OR IMPLIED WARRANTIES, INCLUDING,

BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF

MERCHANTABILITY AND FITNESS FOR A

PARTICULAR PURPOSE ARE DISCLAIMED. IN NO

EVENT SHALL THE FOUNDATION OR CONTRIBUTORS

BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,

SPECIAL, EXEMPLARY, OR CONSEQUENTIAL

DAMAGES (INCLUDING, BUT NOT LIMITED TO,

PROCUREMENT OF SUBSTITUTE GOODS OR

SERVICES; LOSS OF USE, DATA, OR PROFITS; OR

BUSINESS INTERRUPTION) HOWEVER CAUSED AND

ON ANY THEORY OF LIABILITY, WHETHER IN

CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING

NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY

OUT OF THE USE OF THIS SOFTWARE, EVEN IF

ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

Troubleshooting

The following checklist will help you remedy

problems you may encounter with your unit.

Before going through the checklist below, check

the connection and operating procedures.

For details on using the fuse and removing the unit

from the dashboard, see “Connection/Installation”

(page 20).

If the problem is not solved, visit the support site on

the back cover.

General

No power is being supplied to the unit.

 If the unit is turned off and the display

disappears, the unit cannot be operated with the

remote commander.

 Turn on the unit.

No sound or the sound is very low.

 The position of the fader control [FADER] is not

set for a 2-speaker system.

 The volume of the unit and/or connected device

is very low.

 Increase the volume of the unit and connected

device.

No beep sound.

 An optional power amplifier is connected and

you are not using the built-in amplifier.

The contents of the memory have been erased.

 The power supply lead or battery has been

disconnected or not connected properly.

Stored stations and correct time are erased.

The fuse has blown.

Makes a noise when the position of the ignition

is switched.

 The leads are not matched correctly with the car’s

accessory power connector.

During playback or reception, the demonstration

mode starts.

 If no operation is performed for 5 minutes with

[DEMO-ON] set, the demonstration mode starts.

 Set [DEMO-OFF] (page 13).

18GB

The display disappears from/does not appear in

the display window.

 The dimmer is set to [DIM-ON] (page 13).

 The display disappears if you press and hold OFF.

 Press OFF on the unit until the display appears.

 The connectors are dirty (page 15).

The display/illumination flashes.

 The power supply is not sufficient.

 Check that the car battery supplies enough

power to the unit. (The power requirement is

12 V DC.)

The operation buttons do not function.

 Press DSPL and (back)/MODE for more than

2 seconds to reset the unit.

The contents stored in memory are erased.

For your safety, do not reset the unit while you

are driving.

Radio reception

Stations cannot be received.

The sound is hampered by noises.

 The connection is not correct.

 If your car has built-in radio antenna (aerial) in

the rear/side glass, connect an REM OUT lead

(blue/white striped) or accessory power supply

lead (red) to the power supply lead of a car’s

antenna (aerial) booster.

 Check the connection of the car antenna

(aerial).

 If the auto antenna (aerial) will not extend,

check the connection of the power antenna

(aerial) control lead.

Preset tuning is not possible.

 The broadcast signal is too weak.

RDS

PTY displays [- - - - - - - -].

 The current station is not an RDS station.

 RDS data has not been received.

 The station does not specify the program type.

USB device playback

You cannot play items via a USB hub.

 This unit cannot recognize USB devices via a USB

hub.

A USB device takes longer to play.

 The USB device contains files with a complicated

tree structure.

The sound is intermittent.

 The sound may be intermittent at a high-bit-rate.

 DRM (Digital Rights Management) files may not

be playable in some cases.

Audio file cannot be played.

 USB device formatted with file systems other

than FAT16 or FAT32 are unsupported.*

* This unit supports FAT16 and FAT32, but some USB

device may not support all of these FAT. For details,

refer to the operating instruction of each USB device

or contact the manufacturer.

Pandora® operation

Pandora® connection is not possible.

 Shut down the Pandora® application on the

mobile device, and then launch it again.

Error displays/Messages

HUB NO SUPRT: USB hubs are not supported.

IPD STOP: iPod playback has finished.

 Operate your iPod/iPhone to start playback.

NO DEV: A USB device is not connected or

recognized.

 Make sure the USB device or USB cable is securely

connected.

OVERLOAD: The USB device is overloaded.

 Disconnect the USB device, then press SRC to

select another source.

 The USB device has a fault, or an unsupported

device is connected.

19GB

READ: Now reading information.

 Wait until reading is complete and playback

starts automatically. This may take some time

depending on the disc structure.

USB ERROR: The USB device cannot be played.

 Connect the USB device again.

USB NO MUSIC: There is no playable file.

 Connect a USB device containing playable files

(page 16).

USB NO SUPRT: The USB device is not supported.

 For details on the compatibility of your USB

device, visit the support site on the back cover.

For Pandora® operation:

CANNOT SKIP: Skipping tracks is not allowed.

 Wait until the commercial ends, next track

begins, or select another station on the list.

Pandora® limits the number of skips allowed on

their service.

NO NETWORK: The network connection is unstable

or lost.

 Make the network connection again on the

device, or wait until the network connection is

established.

NO STATION - PLEASE - CREATE - STATION - IN -

PANDORA APP: No stations on your account.

 Create the station on the mobile device.

NOT ALLOWED: The selected operation is not

allowed.

 “Thumbs” feedback is not allowed.

 Wait until the commercial ends.

 Some functions, such as Shared Station, do not

permit feedback. Wait until the next track

begins, or select another station on the list.

 Bookmark is not allowed.

 Wait until the commercial ends.

 Select another track or station, then try it again.

PAN ERROR: The selected operation could not be

performed.

 Wait for a while, then try again.

PAN MAINT: The Pandora® server is under

maintenance.

 Wait for a while, then try again.

PAN NO SUPRT: The connected device is not

supported.

 For details of compatible devices, visit the

support site.

PAN OPEN APP: Pandora® is not running.

 Launch the Pandora® application on the iPhone.

PAN RESTRICT: Pandora® is not available outside

your country.

PLEASE LOGIN - PANDORA APP: You are not

logged into your Pandora® account.

 Disconnect the device, log into your Pandora®

account, then connect the device again.

UPDATE PAN: An old version of Pandora® is

connected.

 Update the Pandora® application to the latest

version.

If these solutions do not help improve the situation,

consult your nearest Sony dealer.

20GB

Cautions

 Run all ground (earth) leads to a common

ground (earth) point.

 Do not get the leads trapped under a screw, or

caught in moving parts (e.g., seat railing).

 Before making connections, turn the car ignition

off to avoid short circuits.

 Connect the yellow and red power supply leads

only after all other leads have been connected.

 Be sure to insulate any loose unconnected leads

with electrical tape for safety.

 Choose the installation location carefully so that

the unit will not interfere with normal driving

operations.

 Avoid installing the unit in areas subject to dust,

dirt, excessive vibration, or high temperature,

such as in direct sunlight or near heater ducts.

 Use only the supplied mounting hardware for a

safe and secure installation.

Note on the power supply lead (yellow)

When connecting this unit in combination with other

stereo components, the amperage rating of the car

circuit to which the unit is connected must be higher

than the sum of each component’s fuse amperage

rating.

Mounting angle adjustment

Adjust the mounting angle to less than 45°.

Parts List for Installation

 This parts list does not include all the package

contents.

 The bracket  and the protection collar  are

attached to the unit before shipping. Before

mounting the unit, use the release keys  to

remove the bracket  from the unit. For details,

see “Removing the protection collar and the

bracket” (page 23).

 Keep the release keys  for future use as they are

also necessary if you remove the unit from your

car.

Connection/Installation

Precautions







× 4

5 × max. 8 mm

(

/32 × max.

/16 in)



× 2

La page charge ...

Sony DSX-A200UI Mode d'emploi

Marque: Sony

Modèle: DSX-A200UI

Catégorie: Récepteurs multimédia de voiture

Taper: Mode d'emploi

Télécharger le PDF

rapport

dans d''autres langues

English: Sony DSX-A200UI Operating instructions

Sony DSX-A200UI Mode d'emploi

Sony DSX-A200UI Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents