Simplicity 2691345-01 Manuel utilisateur

Not for

Reproduction

en

Operator’s Manual

es

Manual del operador

fr

Manuel d’utilisation

80012812USCN

Rev. E

Not for

Reproduction

2

Not for

Reproduction

en

Manual Contents:

Operator Safety ................................................................. 3

Features and Controls...................................................... 10

Operation ......................................................................... 12

Maintenance .................................................................... 18

Troubleshooting ............................................................... 23

Specications .................................................................. 25

The images in this document are representative, and

are meant to complement the instructional copy they

accompany. Your unit may vary from the images displayed.

LEFT and RIGHT are as seen from the operator’s position.

Operator Safety

Important Safety Instructions

SAVE THESE INSTRUCTIONS - This manual contains

important instructions that should be followed during the

initial set-up, the operation, and the maintenance of the

equipment. Save these original instructions for future

reference.

Safety Symbols and Meanings

FIRE MOVING

PARTS

SHOCK STOP

TOXIC FUMES KICKBACK EXPLOSION ON OFF

WEAR EYE

PROTECTION

HAZARDOUS

CHEMICAL

HOT

SURFACE

CHOKE

READ

MANUAL

FAST SLOW OIL FUEL

FUEL

SHUT-OFF

ROLL-OVER HAZARD

ROLL-OVER

HAZARD

The safety alert symbol is used to identify safety

information about hazards that can result in personal injury.

A signal word (DANGER, WARNING, or CAUTION) is used

with the alert symbol to indicate the likelihood and the

potential severity of injury. In addition, a hazard symbol may

be used to represent the type of hazard.

DANGER indicates a hazard which, if not

avoided, will result in death or serious injury.

WARNING indicates a hazard which, if not

avoided, could result in death or serious injury.

CAUTION indicates a hazard which, if not

avoided, could result in minor or moderate injury.

NOTICE indicates a situation that could result in

damage to the product.

WARNING

The engine exhaust from this product contains chemicals

known to the State of California to cause cancer, birth

defects, or other reproductive harm.

WARNING

Certain components in this product and its related

accessories contain chemicals known to the State

of California to cause cancer, birth defects, or other

reproductive harm. Wash hands after handling.

WARNING

Battery posts, terminals, and related accessories contain

lead and lead compounds - chemicals known to the

State of California to cause cancer, birth defects, or other

reproductive harm. Wash hands after handling.

WARNING

Running engine gives off carbon monoxide, an odorless,

colorless, poison gas.

Breathing carbon monoxide can cause headache, fatigue,

dizziness, vomiting, confusion, seizures, nausea, fainting

or death.

• Operate equipment ONLY outdoors.

• Keep exhaust gas from entering a confined area

through windows, doors, ventilation intakes, or other

openings.

3

Not for

Reproduction

Safe Operation Practices

Operating Safety

Congratulations on purchasing a superior-quality piece of

lawn and garden equipment. Our products are designed

and manufactured to meet or exceed all industry

standards for safety.

Power equipment is only as safe as the operator. If it is

misused, or not properly maintained, it can be dangerous!

Remember, you are responsible for your safety and that

of those around you.

Use common sense, and think through what you are

doing. If you are not sure that the task you are about to

perform can be safely done with the equipment you have

chosen, ask a professional: contact your local authorized

dealer.

Read the Manual

The operator’s manual contains important safety

information you need to be aware of BEFORE you

operate your unit as well as DURING operation.

Safe operating techniques, an explanation of the

product’s features and controls, and maintenance

information is included to help you get the most out of

your equipment investment.

Be sure to completely read the Safety Rules and

Information found on the following pages. Also completely

read the Operation section.

Children Reverse

Tragic accidents can occur with children. Do not allow

them anywhere near the area of operation. Children are

often attracted to the unit and mowing activity. Never

assume that children will remain where you last saw

them. If there is a risk that children may enter the area

where you are mowing, have another responsible adult

watch them.

DO NOT GIVE CHILDREN RIDES ON THIS UNIT! This

encourages them to come near the unit in the future

while it is running, and they could be seriously hurt. They

may then approach the unit for a ride when you are not

expecting it, and you may run over them.

DO NOT GIVE CHILDREN RIDES ON THIS UNIT! This

encourages them to come near the unit in the future

while it is running, and they could be seriously hurt. They

may then approach the unit for a ride when you are not

expecting it, and you may run over them.

4

Not for

Reproduction

en

Slope Operation

3.5 ft

(1,5 m)

20.0 ft (6,0 m)

You could be seriously injured or even killed if you use this unit on too steep

an incline. Using the unit on a slope that is too steep or where you don’t have

adequate traction can cause you to lose control or roll over.

A good rule of thumb is to not operate on any slope you cannot back up (in

2-wheel drive mode). You should not operate on inclines with a slope greater

than a 3.5 foot rise over a 20 foot length. Always drive up and down slopes:

never cross the face.

Also note that the surface you are driving on can greatly impact stability and

control. Wet grass or icy pavement can seriously affect your ability to control

the unit.

If you feel unsure about operating the unit on an incline, don’t do it. It’s not

worth the risk.

Moving Parts

This equipment has many moving parts that can injure you or someone

else. However, if you are seated in the seat properly and follow all the rules

in this book, the unit is safe to operate.

The mower deck has spinning mower blades that can amputate hands and

feet. Do not allow anyone near the equipment while it is running!

To help you, the operator, use this equipment safely, it is equipped with

an operator-present safety system. Do NOT attempt to alter or bypass the

system. See your dealer immediately if the system does not pass all the

safety interlock system tests found in this manual.

Thrown Objects

This unit has spinning mower blades. These blades can pick up and throw

debris that could seriously injure a bystander. Be sure to clean up the area to

be mowed BEFORE you start mowing.

Do not operate this unit without the entire grass catcher or discharge guard

(deflector) in place.

Do not allow anyone in the mowing area while the unit is running! If someone

does enter the area, shut the unit off immediately until they leave.

Fuel and Maintenance

Gasoline is extremely flammable. Its vapors are also extremely flammable

and can travel to distant ignition sources. Gasoline must only be used as

a fuel, not as a solvent or cleaner. Fuel should never be stored any place

where its vapors can build up or travel to an ignition source like a pilot light.

Fuel belongs in an approved, plastic, sealed gas can, or in the tractor fuel

tank with the cap securely closed. Spilled fuel needs to be cleaned up

immediately.

Proper maintenance is critical to the safety and performance of your unit. Be

sure to perform the maintenance procedures listed in this manual and be

sure to periodically test the safety system.

5

Not for

Reproduction

GENERAL OPERATION

1. Read, understand, and follow all instructions in the manual

and on the unit before starting.

2. Do not put hands or feet near rotating parts or under the

machine. Keep clear of the discharge opening at all times.

3. Only allow responsible adults, who are familiar with the

instructions, to operate the unit (local regulations can

restrict operator age).

4. Clear the area of objects such as rocks, toys, wire, etc.,

which could be picked up and thrown by the blade(s).

5. Be sure the area is clear of other people before mowing.

Stop the unit if anyone enters the area.

6. Never carry passengers.

7. Do not mow in reverse unless absolutely necessary.

Always look down and behind before and while traveling in

reverse.

8. Never direct discharge material toward anyone. Avoid

discharging material against a wall or obstruction.

Material may ricochet back toward the operator. Stop the

blade(s) when crossing gravel surfaces.

9. Do not operate the machine without the entire grass

catcher, discharge guard (deflector), or other safety

devices in place.

10. Slow down before turning.

11. Never leave a running unit unattended. Always disengage

the PTO, set parking brake, stop engine, and remove

starter insert before dismounting.

12. Disengage blades (PTO) when not mowing. Shut off

engine and wait for all parts to come to a complete stop

before cleaning the machine, removing the grass catcher,

or unclogging the discharge guard.

13. Operate the machine only in daylight or good artificial light.

14. Do not operate the unit while under the influence of alcohol

or drugs.

15. Watch for traffic when operating near or crossing

roadways.

16. Use extra care when loading or unloading the unit into a

trailer or truck.

17. Always wear eye protection when operating this unit.

18. Data indicates that operators, age 60 years and above,

are involved in a large percentage of power equipment-

related injuries. These operators should evaluate their

ability to operate the equipment safely enough to protect

themselves and others from injury.

19. Follow the manufacturer’s recommendations for wheel

weights or counterweights.

20. Keep in mind the operator is responsible for accidents

occurring to other people or property.

21. All drivers should seek and obtain professional and

practical instruction.

22. Always wear substantial footwear and trousers. Never

operate when barefoot or wearing sandals.

23. Before using, always visually check that the blades and

blade hardware are present, intact, and secure. Replace

worn or damaged parts.

24. Disengage attachments before: refueling, removing an

attachment, making adjustments (unless the adjustment

can be made from the operator’s position).

25. When the machine is parked, stored, or left unattended,

lower the cutting means unless a positive mechanical lock

is used.

26. Before leaving the operator’s position for any reason,

engage the parking brake, disengage the PTO, stop the

engine, and remove the starter insert.

27. To reduce fire hazard, keep the unit free of grass, leaves,

& excess oil. Do not stop or park over dry leaves, grass, or

combustible materials.

TRANSPORTING AND STORAGE

1. When transporting the unit on an open trailer, make sure

it is facing forward, in the direction of travel. If the unit is

facing backwards, wind lift could damage the unit.

2. Always observe safe refueling and fuel handling practices

when refueling the unit after transportation or storage.

3. Never store the unit (with fuel) in an enclosed poorly

ventilated structure. Fuel vapors can travel to an ignition

source (such as a furnace, water heater, etc.) and cause

an explosion. Fuel vapor is also toxic to humans and

animals.

4. Always follow the engine manual instructions for storage

preparations before storing the unit for both short and long

term periods.

5. Always follow the engine manual instructions for proper

start-up procedures when returning the unit to service.

6. Never store the unit or fuel container inside where there is

an open flame or pilot light, such as in a water heater. Allow

unit to cool before storing.

Read these safety rules and follow them closely. Failure to obey these rules could result in loss of control of unit,

severe personal injury or death to you, or bystanders, or damage to property or equipment. This mowing deck

is capable of amputating hands and feet and throwing objects. The triangle in text signifies important

cautions or warnings which must be followed.

6

Not for

Reproduction

en

WARNING

Never operate on slopes greater than 17.6 percent (10°)

which is a rise of 3-1/2 feet (106 cm) vertically in 20 feet

(607 cm) horizontally.

When operating on slopes use additional wheel weights

or counterweights. See your dealer/retailer to determine

which weights are available and appropriate for your unit.

Select slow ground speed before driving onto slope.

In addition to front weights, use extra caution when

operating on slopes with rear-mounted grass catchers.

Mow UP and DOWN the slope, never across the face,

use caution when changing directions and DO NOT

START OR STOP ON SLOPE.

CHILDREN

Tragic accidents can occur if the operator is not alert to the

presence of children. Children are often attracted to the unit

and the mowing activity. Never assume that children will

remain where you last saw them.

1. Keep children out of the mowing area and under the

watchful care of another responsible adult.

2. Be alert and turn unit off if children enter the area.

3. Before and during reverse operation, look behind and

down for small children.

4. Never carry children, even with the blade(s) off. They may

fall off and be seriously injured or interfere with safe unit

operation. Children who have been given rides in the past

may suddenly appear in the mowing area for another ride

and be run over or backed over by the machine.

5. Never allow children to operate the unit.

6. Use extra care when approaching blind corners, shrubs,

trees, or other objects that may obscure vision.

EMISSIONS

1. Engine exhaust from this product contains chemicals

known, in certain quantities, to cause cancer, birth

defects, or other reproductive harm.

2. Look for the relevant Emissions Durability Period and Air

Index information on the engine emissions label.

SLOPE OPERATION

Slopes are a major factor related to loss-of-control and tip-

over accidents, which can result in severe injury or death.

Operation on all slopes requires extra caution. If you

cannot back up the slope or if you feel uneasy on it, do not

operate on it.

Control of a ride-on machine sliding on a slope will not be

regained by the application of the brake. The main reasons

for loss of control are: insufficient tire grip on the ground,

speed too fast, inadequate braking, the type of machine

is unsuitable for its task, lack of awareness of the ground

conditions, incorrect hitching and load distribution.

1. Mow up and down slopes, not across.

2. Watch for holes, ruts, or bumps. Uneven terrain could

overturn the unit. Tall grass can hide obstacles.

3. Choose a slow speed so that you will not have to stop or

change speeds while on the slope.

4. Do not mow on wet grass. Tires may lose traction.

5. Always keep unit in gear especially when traveling down

slopes. Do not shift to neutral and coast downhill.

6. Avoid starting, stopping, or turning on a slope. If tires

lose traction, disengage the blade(s) and proceed slowly

straight down the slope.

7. Keep all movement on slopes slow and gradual. Do

not make sudden changes in speed or direction, which

could cause the machine to rollover.

8. Use extra care while operating machines with grass

catchers or other attachments; they can affect the

stability of the unit. Do not use on steep slopes.

9. Do not try to stabilize the machine by putting your foot on

the ground (ride-on units).

10. Do not mow near drop-offs, ditches, or embankments.

The mower could suddenly turn over if a wheel is over

the edge of a cliff or ditch, or if an edge caves in.

11. Do not use grass catchers on steep slopes.

12. Do not mow slopes if you cannot back up them.

13. See your authorized dealer/retailer for recommendations

of wheel weights or counterweights to improve stability.

14. Remove obstacles such as rocks, tree limbs, etc.

15. Use slow speed. Tires may lose traction on slopes even

through the brakes are functioning properly.

16. Do not turn on slopes unless necessary, and then, turn

slowly and gradually downhill, if possible.

TOWED EQUIPMENT (RIDE-ON UNITS)

1. Tow only with a machine that has a hitch designed for

towing. Do not attach towed equipment except at the

hitch point.

2. Follow the manufacturer’s recommendations for weight

limit for towed equipment and towing on slopes.

3. Never allow children or others in or on towed equipment.

4. On slopes, the weight of the towed equipment may

cause loss of traction and loss of control.

5. Travel slowly and allow extra distance to stop.

6. Do not shift to neutral and coast down hill.

7

Not for

Reproduction

SERVICE AND MAINTENANCE

Safe Handling of Gasoline

1. Extinguish all cigarettes, cigars, pipes, and other sources

of ignition.

2. Use only approved gasoline containers.

3. Never remove the gas cap or add fuel with the engine

running. Allow the engine to cool before refueling.

4. Never fuel the machine indoors.

5. Never store the machine or fuel container where there is an

open flame, spark, or pilot light such as near a water heater

or other appliance.

6. Never fill containers inside a vehicle or on a truck bed with

a plastic bed liner. Always place containers on the ground

away from your vehicle before filling.

7. Remove gas-powered equipment from the truck or

trailer and refuel it on the ground. If this is not possible,

then refuel such equipment on a trailer with a portable

container, rather than from a gasoline dispenser nozzle.

8. Keep nozzle in contact with the rim of the fuel tank or

container opening at all times until fueling is complete. Do

not use a nozzle lock-open device.

9. If fuel is spilled on clothing, change clothing immediately.

10. Never over-fill the fuel tank. Replace gas cap and tighten

securely.

11. Use extra care in handling gasoline and other fuels. They

are flammable and vapors are explosive.

12. If fuel is spilled, do not attempt to start the engine but

move the machine away from the area of spillage and

avoid creating any source of ignition until fuel vapors have

dissipated.

13. Replace all fuel tank caps and fuel container caps securely.

Service & Maintenance

1. Never run the unit in an enclosed area where carbon

monoxide fumes may collect.

2. Keep nuts and bolts, especially blade attachment bolts,

tight and keep equipment in good condition.

3. Never tamper with safety devices. Check their proper

operation regularly and make necessary repairs if they are

not functioning properly.

4. Keep unit free of grass, leaves, or other debris build-up.

Clean up oil or fuel spillage and remove any fuel-soaked

debris. Allow machine to cool before storage.

5. If you strike an object, stop and inspect the machine.

Repair, if necessary, before restarting.

6. Never make adjustments or repairs with the engine

running.

7. Check grass catcher components and the discharge guard

frequently and replace with manufacturer’s recommended

parts, when necessary.

8. Mower blades are sharp. Wrap the blade or wear gloves,

and use extra caution when servicing them.

9. Check brake operation frequently. Adjust and service as

required.

10. Maintain or replace safety and instructions labels, as

necessary.

11. Do not remove the fuel filter when the engine is hot as

spilled gasoline may ignite. Do not spread fuel line clamps

further than necessary. Ensure clamps grip hoses firmly

over the filter after installation.

12. Do not use gasoline containing METHANOL, gasohol

containing more than 10% ETHANOL, gasoline additives,

or white gas because engine/fuel system damage could

result.

13. If the fuel tank must be drained, it should be drained

outdoors.

14. Replace faulty silencers/mufflers.

15. Use only factory authorized replacement parts when

making repairs.

16. Always comply with factory specifications on all settings

and adjustments.

17. Only authorized service locations should be utilized for

major service and repair requirements.

18. Never attempt to make major repairs on this unit unless

you have been properly trained. Improper service

procedures can result in hazardous operation, equipment

damage and voiding of manufacturer’s warranty.

19. On multiple blade mowers, take care as rotating one blade

can cause other blades to rotate.

20. Do not change engine governor settings or over-speed

the engine. Operating the engine at excessive speed can

increase the hazard of personal injury.

21. Disengage drive attachments, stop the engine, remove the

starter insert, and disconnect the spark plug wire(s) before:

clearing attachment blockages and chutes, performing

service work, striking an object, or if the unit vibrates

abnormally. After striking an object, inspect the machine for

damage and make repairs before restarting and operating

the equipment.

22. Never place hands near the moving parts, such as a hydro

pump cooling fan, when the tractor is running. (Hydro

pump cooling fans are typically located on top of the

transaxle).

23. Units with hydraulic pumps, hoses, or motors:

WARNING: Hydraulic fluid escaping under pressure may

have sufficient force to penetrate skin and cause serious

injury. If foreign fluid is injected into the skin it must be

surgically removed within a few hours by a doctor familiar

with this form of injury or gangrene may result. Keep

body and hands away from pin holes or nozzles that

eject hydraulic fluid under high pressure. Use paper or

cardboard, and not hands, to search for leaks. Make sure

all hydraulic fluid connections are tight and all hydraulic

hoses and lines are in good condition before applying

pressure to the system. If leaks occur, have the unit

serviced immediately by your authorized dealer.

24. WARNING: Improper release of springs can result in

serious personal injury. Springs should be removed by an

authorized technician.

25. Models equipped with an engine radiator:

WARNING: To prevent serious bodily injury from hot

coolant or steam blow-out, never attempt to remove the

radiator cap while the engine is running. Stop the engine

and wait until it is cool. Even then, use extreme care when

removing the cap.

8

Not for

Reproduction

en

Safety Decals

All safety messages on your rider and mower should be

carefully read and obeyed (see Figure 1). Personal bodily

injury can result when these instructions are not followed.

The information is for your safety and it is important! The

safety decals below are on your rider and mower.

If any of these decals are lost or damaged, replace them at

once. See an authorized dealer for replacements.

1730202

1730264

Height of Cut

Transmission Release

DANGER Main PanelDANGER Amputation Hazard

Figure 1

If any of these decals are lost or damaged, replace them at

once. See an authorized dealer for replacements.

These labels are easily applied and will act as a constant

visual reminder to you, and others who may use the

equipment, to follow the safety instructions necessary for

safe, effective operation.

9

Not for

Reproduction

Features and Controls

Figure 2

4

3

2

1

10

Not for

Reproduction

en

Refer to the illustration in Figure 2 that matches your unit.

Brake Pedal

Depressing the brake pedal applies the tractor

brake.

Cruise Control

This locks the ground speed control in forward.

The cruise control has five lock positions.

Fuel Tank

To remove the cap, turn counterclockwise.

Ground Speed Pedals

The forward ground speed pedal controls the

tractor’s forward ground speed. The reverse

ground speed pedal controls the tractor’s reverse

ground speed.

Headlight Switch

This turns the tractor headlights on and off.

Mower Height of Cut Adjustment

The mower cutting height adjustment lever

controls the cutting height. The cutting height can

be set to one of seven positions between 1.5” and

4.0” (3,8 and 10,2 cm).

Parking Brake

This locks the parking brake when the tractor is

stopped. See Parking Brake section.

Power Take-Off (PTO) Switch

The PTO (Power Take-Off ) switch engages and

disengages the mower blade clutch. To engage

the PTO, pull UP on the switch. Push DOWN to

disengage.

NOTE: The operator must be seated firmly in the

tractor seat for the PTO to function.

Reverse Mowing Option (RMO)

This allows the operator to mow (or use other

PTO driven attachments) while traveling in

reverse. To activate, turn the RMO key after the

PTO is engaged. The L.E.D. light will illuminate,

and the operator can then mow in reverse. Each

time the PTO is engaged, the RMO needs to be

reactivated if desired.

Ignition Switch

The ignition switch starts and stops the engine, it

has three positions:

OFF: Stops the engine and shuts off the

electrical system.

RUN: Allows the engine to run and powers

the electrical system.

START: Cranks the engine for starting.

Throttle/Choke Control (Choke-A-Matic)

The throttle/choke controls the engine speed

and choke. Move the throttle/choke control to

the FAST position to increase engine speed

and SLOW position to decrease engine speed.

Always operate at full throttle. Move the throttle/

choke control to the CHOKE position for starting

a cold engine. A warm engine may not require

choking.

Transmission Release Lever

This releases the transmission so that the tractor

can be pushed by hand.

Hourmeter (if equipped)

The hour meter measures the number of hours

the key has been in the RUN position.

11

Not for

Reproduction

Operation

General Operating Safety

Be sure to read all information in the Operator Safety

section before attempting to operate this unit. Become

familiar with all of the controls and how to stop the unit.

WARNING

If the unit does not pass a safety test, do not operate it.

See an authorized dealer.

Safety Interlock System Tests

This unit is equipped with a Safety Interlock System. Do not

attempt to bypass or tamper with the switches/devices.

Test 1 — Engine should NOT crank if:

• PTO switch is ON, OR

• Brake pedal is NOT fully depressed (parking brake

OFF), OR

Test 2 — Engine SHOULD crank and start if:

• Operator is sitting in seat, AND

• PTO switch is OFF, AND

• Brake pedal is fully depressed (parking brake ON).

Test 3 — Engine should SHUT OFF if:

• Operator rises off seat.

Test 4 — Check Mower Blade Stopping Time

Mower blades and mower drive belt should come to a

complete stop within five seconds after electric PTO switch

is turned OFF. If mower drive belt does not stop within five

seconds, see an authorized dealer.

Test 5 — Reverse Mow Option (RMO) Check

• Engine should shut off if reverse travel is attempted if

the PTO has been switched on and RMO has not been

activated.

• RMO light should illuminate when RMO has been

activated.

WARNING

Mowing in reverse can be hazardous to bystanders. Tragic

accidents can occur if the operator is not alert to the

presence of children. Never activate the RMO if children

are present. Children are often attracted to the unit and

the mowing activity.

Check Tire Pressure

Tires should be checked periodically to provide the

optimum traction and to guarantee the best cut (see Figure

3).

NOTE: These pressures may differ slightly from the

“Maximum Inflation” stamped on the side walls of the tires.

10 psi

(0,68 bar)

12-14 psi

(0,82-0,96 bar)

Figure 3

Oil Recommendations

We recommend the use of Briggs & Stratton Warranty

Certified oils for best performance. Other high-quality

detergent oils are acceptable if classified for service SF,

SG, SH, SJ or higher. Do not use special additives.

Outdoor temperatures determine the proper oil viscosity for

the engine. Use the chart to select the best viscosity for the

outdoor temperature range expected.

* Below 40°F (4°C) the use of SAE 30 will result in hard starting.

** Above 80°F (27°C) the use of 10W-30 may cause increased oil

consumption. Check oil level more frequently.

12

Not for

Reproduction

en

Check and Add Engine Oil

Before adding or checking the oil

• Place the tractor on a level surface (see Figure 4).

• Clean the oil fill area of any debris.

1. Remove the dipstick (A, Figure 5) and wipe with a clean

cloth.

2. Insert and tighten the dipstick.

3. Remove the dipstick and check the oil level. It should be

at the FULL mark (B) on the dipstick.

4. If low, add oil slowly into the engine oil fill (C). Do not

overfill. After adding oil, wait one minute and then

recheck the oil level.

NOTE: Do not add oil at the quick oil drain (if equipped).

5. Replace and tighten the dipstick.

Figure 4

Oil Pressure

If the oil pressure is too low, a pressure switch (if equipped)

will either stop the engine or activate a warning device on

the equipment. If this occurs, stop the engine and check the

oil level with the dipstick.

If the oil level is below the ADD mark, add oil until it reaches

the FULL mark. Start the engine and check for proper

pressure before continuing to operate.

If the oil level is between the ADD and FULL marks, do not

start the engine. Contact an authorized dealer to have the

oil pressure problem corrected.

A

B

C

D

Figure 5

13

Not for

Reproduction

Adding Fuel

WARNING

Fuel and its vapors are extremely flammable and

explosive.

Fire or explosion can cause severe burns or death.

When Adding Fuel

• Turn engine off and let engine cool at least 3 minutes

before removing the fuel cap.

• Fill fuel tank outdoors or in well-ventilated area.

• Do not overfill fuel tank. To allow for expansion of the

fuel, do not fill above the bottom of the fuel tank neck.

• Keep fuel away from sparks, open flames, pilot lights,

heat, and other ignition sources.

• Check fuel lines, tank, cap, and fittings frequently for

cracks or leaks. Replace if necessary.

• If fuel spills, wait until it evaporates before starting

engine.

1. Clean the fuel cap area of dirt and debris. Remove the

fuel cap (

A, Figure 6). Also see Features and Controls

section.

2. Fill the fuel tank (B) with fuel. To allow for expansion of

the fuel, do not fill above the bottom of the fuel tank

neck (C).

3. Reinstall the fuel cap.

B

A

C

Figure 6

Fuel Recommendations

Fuel must meet these requirements:

• Clean, fresh, unleaded gasoline.

• A minimum of 87 octane/87 AKI (91 RON). High altitude

use, see below.

• Gasoline with up to 10% ethanol (gasohol) is

acceptable.

NOTICE: Do not use unapproved gasolines, such as E15

and E85. Do not mix oil in gasoline or modify the engine to

run on alternate fuels. Use of unapproved fuels will damage

the engine components and void the engine warranty.

To protect the fuel system from gum formation, mix a fuel

stabilizer into the fuel. See Storage. All fuel is not the

same. If starting or performance problems occur, change

fuel providers or change brands. This engine is certified to

operate on gasoline. The emissions control system for this

engine is EM (Engine Modifications)

High Altitude

At altitudes over 5,000 feet (1524 meters), a minimum 85

octane/85 AKI (89 RON) gasoline is acceptable. To remain

emissions compliant, high altitude adjustment is required.

Operation without this adjustment will cause decreased

performance, increased fuel consumption, and increased

emissions. See an authorized Briggs & Stratton Dealer for

high altitude adjustment information.

Operation of the engine at altitudes below 2,500 feet

(762 meters) with the high altitude adjustment is not

recommended.

14

Not for

Reproduction

en

Starting the Engine

WARNING

Fuel and its vapors are extremely flammable and

explosive.

Fire or explosion can cause severe burns or death.

When Starting Engine

• Ensure that spark plug, muffler, fuel cap, and air

cleaner (if equipped) are in place and secured.

• Do not crank engine with spark plug removed.

• If engine floods, set choke (if equipped) to OPEN/RUN

position, move throttle (if equipped) to FAST position

and crank until engine starts.

WARNING

Engines give off carbon monoxide, an odorless, colorless,

poison gas.

Breathing carbon monoxide can cause nausea, fainting,

or death.

Fire or explosion can cause severe burns or death.

• Start and run engine outdoors.

• Do not start or run engine in enclosed area, even if

doors or windows are open.

1. Check the oil level (see Check and Add Engine Oil).

2. Make sure equipment drive controls are disengaged.

3. Sit in the seat and lift UP the seat adjustment lever,

position as desired, and release the lever to lock the

seat in position.

4. Engage the parking brake. Fully depress the brake

pedal, pull UP on the parking brake control, and release

the brake pedal.

5. Disengage PTO switch by pushing IN.

6. Set the throttle/choke control to the CHOKE position.

7. Insert the key into the ignition switch and turn it to the

ON/START position.

8. After the engine starts, move the throttle/choke control

to half speed. Warm up the engine by running it for at

least 30 seconds.

9. Set throttle/choke control to the FAST position.

In the event of an emergency the engine can be

stopped by simply turning the ignition switch to STOP.

Use this method only in emergency situations. For normal

engine shut down follow the procedure given in Stopping

the Tractor and Engine.

NOTE: If the engine does not start after repeated attempts,

contact an authorized dealer.

Driving the Tractor

1. Sit in the seat and adjust the seat so that you can

comfortably reach all the controls and see the

dashboard display (see Features and Controls).

2. Engage the parking brake. Fully depress the brake

pedal, pull UP on the parking brake control, and release

the brake pedal.

3. Make sure the PTO switch is disengaged.

4. Start the engine (see Starting the Engine).

5. Disengage the parking brake. Fully depress the brake

pedal, press DOWN on the parking brake control, and

release the brake pedal.

6. Depress the forward ground speed control pedal to

travel forward. Release the pedal to stop. Note that

the further down the pedal is depressed the faster the

tractor will travel.

7. Stop the tractor by releasing the ground speed control

pedals, setting the parking brake, and stopping the

engine (see Stopping the Tractor and Engine).

Mowing

1. Set the cutting height to the desired level using

the mower cutting height lever (see Features and

Controls).

2. Engage the parking brake. Make sure the PTO switch is

disengaged.

3. Start the engine (see Starting the Engine).

4. Set the throttle control to the FAST position.

5. Engage the PTO to activate the mower blades.

6. Disengage the parking brake then begin mowing.

7. When finished mowing, shut off the PTO.

8. STOP the engine (see Stopping the

Tractor and Engine).

WARNING

The engine will shut off if the reverse ground speed pedal is

depressed while the PTO is on and the RMO has not been

activated. The operator should always turn the PTO off prior

to driving across on roads, paths, or any area that may be

used by other vehicles. Sudden loss of drive could create a

hazard.

15

Not for

Reproduction

Adjusting the Mower Cutting Height

Use the mower cutting height adjustment lever to raise or

lower the cutting height (see Features and Controls).

The cutting height has seven positions between 1.5” and

4.0” (3,8 and 10,2 cm).

Hourmeter (if equipped)

The Hourmeter (Figure 8) displays the total hours, trip

hours, and digtal clock.

Total Trip / Hours Clock

RESET MODE

Figure 8

Display Total Hours, Trip Hours, and Clock

NOTE: Whenever you start up the unit, the Total Hours are

displayed. The Total Hours will automatically reset to 0 after

999.9.

1. Press MODE for less than 1 second to display the Trip

Hours.

2. Press RESET for greater than 3 seconds to reset the

Trip Hours to 0.

3. Press MODE for less than 1 second to display the Clock

(see Set the Clock section).

4. Press MODE for less than 1 second to return to Total

Hours.

Set the Clock

1. Press MODE for greater than 3 seconds. The hours will

flash on the display.

2. Press RESET to adjust the hours.

3. Press MODE for less than 1 second to save the setting.

The minutes will flash on the display.

4. Press RESET to adjust the minutes.

5. Press MODE for less than 1 second to save the setting.

Reverse Mowing Option (RMO)

WARNING

Mowing in reverse can be hazardous to bystanders. Tragic

accidents can occur if the operator is not alert to the

presence of children. Never activate the RMO if children

are present. Children are often attracted to the unit and

the mowing activity.

The Reverse Mowing Option (RMO) allows the operator to

mow in reverse (see Features and Controls). To activate,

turn the RMO key after the PTO is engaged. The L.E.D. light

will illuminate, and the operator can then mow in reverse.

Each time the PTO is engaged the RMO needs to be

reactivated if desired. The key should be removed to restrict

access to the RMO.

Pushing the Tractor by Hand

1. Disengage the PTO and turn the engine off.

2. Pull the transmission release (A, Figure 7) to lock into

released position.

3. The tractor can now be pushed by hand.

WARNING

Towing the unit will cause transmission damage. Do

not use another vehicle to push or pull this unit. Do not

actuate the transmission release lever while the engine is

running.

A

Figure 7

16

Not for

Reproduction

en

Parking Brake

Use the parking brake control to engage or disengage the

parking brake when the tractor is stopped (Features and

Controls).

Engage the Parking Brake - To engage the parking brake,

fully depress the brake pedal, pull UP on the parking brake

control, and release the brake pedal.

Disengage the Parking Brake - To disengage the parking

brake, fully depress the brake pedal, press DOWN on the

parking brake control, and release the brake pedal.

Cruise Control

TO ENGAGE:

1. Depress the forward ground speed pedal (see Features

and Controls).

2. Pull up the cruise control when the desired speed is

reached. The cruise will lock in one of its five locking

positions.

TO DISENGAGE:

1. Depress the brake pedal.

OR

2. Depress the forward ground speed pedal.

Stopping the Tractor and Engine

WARNING

Fuel and its vapors are extremely flammable and

explosive.

Fire or explosion can cause severe burns or death.

• Do not choke the carburetor to stop the engine.

1. Release the ground speed pedals to return to the

NEUTRAL position (see Features and Controls).

2. While still on the lawn, disengage the PTO switch, then

wait for all moving parts to stop.

3. Move the throttle control (or throttle/choke control)

to SLOW position and turn the ignition key to OFF.

Remove the key.

4. Engage the parking brake. Fully depress the brake

pedal, pull UP on the parking brake control, and release

the brake pedal.

In the event of an emergency the engine can be

stopped by simply turning the ignition switch to STOP.

17

Not for

Reproduction

Maintenance

Maintenance Chart

TRACTOR AND MOWER

Every 8 Hours or Daily

Check safety interlock system

Clean debris off tractor and mower deck

Clean debris from engine compartment

Every 25 Hours or Annually *

Check tire pressure

Check mower blade stopping time

Check tractor and mower for loose hardware

Every 50 Hours or Annually *

Clean battery and cables

Check tractor brakes

See Dealer Annually to

Lubricate tractor and mower

Check mower blades **

* Whichever comes first

** Check blades more often in regions with sandy soils or high dust

conditions.

WARNING

Unintentional sparking can result in fire or electric shock.

Unintentional start-up can result in entanglement,

traumatic amputation, or laceration.

Before performing adjustments or repairs:

• Disconnect the spark plug wire and keep it away from

the spark plug.

• Disconnect battery at negative terminal (only engines

with electric start).

• Use only correct tools.

• Do not tamper with governor spring, links, or other

parts to increase engine speed.

• Replacement parts must be of the same design and

installed in the same position as the original parts.

Other parts may not perform as well, may damage the

unit, and may result in injury.

• Do not strike the flywheel with a hammer or hard object

because the flywheel may shatter during operation.

ENGINE

First 5 Hours

Change engine oil

Every 8 Hours or Daily

Check engine oil level

Every 25 Hours or Annually *

Clean engine air filter and pre-cleaner **

Every 50 Hours or Annually *

Change engine oil

Replace oil filter

Annually

Replace air filter

Replace pre-cleaner

See Dealer Annually to

Inspect muffler and spark arrester

Replace spark plug

Replace fuel filter

Clean engine air cooling system

* Whichever comes first

** Clean more often in dusty conditions or when airborne debris is present.

Check Tire Pressure

Tires should be checked periodically to provide the

optimum traction and to guarantee the best cut (see Figure

5).

NOTE: These pressures may differ slightly from the

“Maximum Inflation” stamped on the side walls of the tires.

Check Mower Blade Stopping Time

WARNING

If the mower blade does not come to a complete stop

within 5 seconds, the clutch must be adjusted. Do not

operate the machine until the proper adjustment has been

performed by an authorized dealer.

Check the mower blade for proper function (see Safety

Interlock System Tests). The blade should stop rotating in

5 seconds or less after moving the blade control to the OFF

position.

18

Not for

Reproduction

en

Battery Maintenance

WARNING

When removing or installing battery cables, disconnect

the negative cable FIRST and reconnect it LAST. If not

done in this order, the positive terminal can be shorted to

the frame by a tool.

WARNING

If the mower blade does not come to a complete stop

within 5 seconds, the clutch must be adjusted. Do not

operate the machine until the proper adjustment has been

performed by an authorized dealer.

Cleaning the Battery and Cables

1. Disconnect the NEGATIVE (black) cables first.

2. Disconnect the POSITIVE (red) cables last.

3. Remove and Install the battery as shown in Figure 8.

4. Clean the battery platform with a solution of baking soda

and water.

5. Clean the battery terminals and cable ends with a wire

brush and battery terminal cleaner until shiny.

6. Coat the assembled terminals with petroleum jelly or

non-conducting grease.

7. Connect the POSITIVE (red) cables first.

8. Connect the NEGATIVE (black) cables last.

( )

+

WARNING

DO

N

OT

R

EMO

V

E

C

O

V

ER

WARNING

DO NOT REMOVE

COVER

(2x)

( )

(3x)

D

C

Figure 9

Charging the Battery

WARNING

Keep open flames and sparks away from the battery; the

gasses coming from it are highly explosive. Ventilate the

battery well during charging.

A dead battery or one too weak to start the engine may

be the result of a defect in the charging system or other

electrical component. If there is any doubt about the cause

of the problem, see your dealer. If you need to replace the

battery, follow the steps under Cleaning the Battery and

Cables.

To charge the battery, follow the instructions provided by

the battery charger manufacturer as well as all warnings

included in the safety rules sections of this book. Charge

the battery until fully charged. Do not charge at a rate higher

than 10 amps.

Changing the Engine Oil

WARNING

Fuel and its vapors are extremely flammable and

explosive.

Fire or explosion can cause severe burns or death.

When Changing Oil

• If you drain the oil from the top oil fill tube, the fuel tank

must be empty or fuel can leak out and result in a fire or

explosion.

1. Run engine until warm.

2. Place the tractor on a level surface (see Figure 4).

3. Stop the engine.

4. Clean oil fill and filter areas of any debris. Remove

dipstick and lay on clean cloth (see Figure 5).

5. Remove the oil drain cap as shown in Figure 9. Drain

the oil into an approved container. After the oil has

drained, install the oil drain cap.

Figure 10

19

Not for

Reproduction

Servicing the Air Filter

WARNING

Fuel and its vapors are extremely flammable and

explosive.

Fire or explosion can cause severe burns or death.

• Never start or run the engine with the air cleaner

assembly or air filter removed..

NOTICE: Do not use pressurized air or solvents to clean the

filter. Pressurized air can damage the filter and solvents will

dissolve the filter.

1. Remove the fasteners (A, Figure 11) and the air filter

cover (B).

2. To remove the filter (C), lift the end of the filter and then

pull the filter off the intake (D).

3. To loosen debris, gently tap the filter on a hard surface.

If the filter is excessively dirty, replace with a new filter.

4. Wash the pre-cleaner in liquid detergent and water.

Then allow it to thoroughly air dry. Do not oil the pre-

cleaner.

5. Assemble the dry pre-cleaner to the filter.

6. Install the filter on the intake. Push the end of the filter

into the base as shown. Make sure filter fits securely in

the base.

7. Install air filter cover and secure with fasteners.

C

A

D

B

Figure 12

6. Remove the oil filter (see Figure 10) and dispose of

properly.

7. Lightly lubricate the oil filter gasket with fresh, clean oil.

8. Install the oil filter by hand until the gasket contacts the

oil filter adapter, then tighten the oil filter 1/2 to 3/4 turns.

9. Add oil (see Check and Add Engine Oil).

B

Figure 11

20

La page charge ...

Simplicity 2691345-01 Manuel utilisateur

Ce manuel convient également à

Simplicity 2691345-01 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents