Eskimo F1 ROCKET Manuel utilisateur

Marque: Eskimo

Modèle: F1 ROCKET

Taper: Manuel utilisateur

Ce manuel convient également à

F1R08
F1R10

28284

ECN #11656

REV1 05/24/2017

Operator's Manual

Original Operating Instructions

F1 ROCKET

™

33cc POWER ICE AUGER

Get parts online at

www.GetEskimo.com

GAS/OIL

RATIO

50:1

F1 ROCKET

™

33cc POWER ICE AUGER

Check for parts online at www.GetEskimo.com or call 800-345-6007 M-F 8-5 CDT

Operator's Manual

ESKIMO

Power Ice Auger

INTRODUCTION

Thank you

for purchasing an Eskimo® Power Ice Auger from Ardisam, Inc. We have worked to ensure that this ice auger meets high

standards for usability and durability. With proper care, your ice auger will provide you many years of service. Please take the time

to read this manual carefully to learn how to correctly operate and maintain your ice auger. Congratulations on your investment

in quality. Save these instructions for future reference. Ardisam, Inc reserves the right to change or alter this manual without notice.

CONTENTS

Registration .....................................................................................................................................................................................................................................................................2

Important Safety Precautions ............................................................................................................................................................................................................................... 3-6

Pre-Operation ............................................................................................................................................................................................................................................................. 6-7

Operation .........................................................................................................................................................................................................................................................................7

Maintenance and Storage ................................................................................................................................................................................................................................... 8-10

Service, Troubleshooting and Repair ............................................................................................................................................................................................................10-11

Warranty ..................................................................................................................................................................................................................................................................12-15

FEDERAL EMISSION INFORMATION

Viper warrants to the retail purchaser, that this small, o-road engine was designed, built and equipped to conform at the time of initial

sale to all applicable regulations of the U.S. Environmental Protection Agency (EPA).

REGISTRATION AND SERVICE

Record the product model number and serial number in the space provided for easy reference when ordering parts or requesting

technical support. Excluding emissions-related warranty items, the warranty is valid only if the completed registration is received

by Viper within 30 days of purchase. (SEE WARRANTY SECTION FOR MORE INFORMATION.) You can register your warranty online

by visiting www.ardisam.com, or by mailing it to: Ardisam, Inc., 1160 Eighth Avenue, Cumberland, WI 54829. For service questions,

call our customer service department at (800) 345-6007 Mondays through Fridays from 8 a.m. to 5 p.m. CDT.

OWNERSHIP RECORDS

Place of Purchase:

Place of Purchase Address:

City: State/Province: Zip Code/Postal Code:

Model Number: Serial Number (found next to warning tag):

Date of Purchase:

Notes:

This manual may contain information for several models. Read and keep this manual for future reference. This manual contains

important information on SAFETY, ASSEMBLY, OPERATION, AND MAINTENANCE. The owner must be certain that all the product

information is included with the unit. This information includes the MANUAL, the REPLACEMENT PARTS and the WARRANTIES.

This information must be included to make sure state laws and other laws are followed. This manual should remain with the

unit even if it is resold.

Check for parts online at www.GetEskimo.com or call 800-345-6007 M-F 8-5 CDT

Operator's Manual

ESKIMO

Power Ice Auger

WARNINGS AND SAFETY PRECAUTIONS

OPERATOR’S RESPONSIBILITY

Accurate, safe and eective use of this unit is the operator’s

responsibility.

• Read and follow all safety instructions.

• Carefully follow all assembly instructions.

• Maintain the unit according to directions and schedule

included in this Eskimo operator’s manual.

• Ensure that anyone who uses the unit is familiar with and

understands all controls and safety precautions.

SAFETY MESSAGES

Your manual contains special messages to bring attention to

potential safety concerns, engine damage as well as helpful

operating and servicing information. Please read all the infor-

mation carefully to avoid injury and damage to the unit.

NOTE: General information is given throughout the manual

that may help the operator in the operation or service of the

unit.

This symbol points out important safety instruc-

tions which if not followed could endanger your

personal safety.

BEFORE OPERATING:

WARNING

WARNING INDICATES A HAZARD WHICH, IF NOT

AVOIDED, COULD RESULT IN DEATH OR SERIOUS IN

JURY AND/OR PROPERTY DAMAGE.

CAUTION

CAUTION INDICATES YOU CAN BE HURT OR YOUR

EQUIPMENT DAMAGED IF THE SAFETY INSTRUC

TIONS THAT FOLLOW THIS SIGNAL WORD ARE NOT

OBEYED.

WARNING

CALIFORNIA PROPOSITION 65 WARNING

ENGINE EXHAUST FROM THIS PRODUCT CONTAINS

CHEMICALS KNOWN TO THE STATE OF CALIFORNIA

TO CAUSE CANCER, BIRTH DEFECTS, OR OTHER RE

PRODUCTIVE HARM.

IMPORTANT

INDICATES HELPFUL INFORMATION FOR PROPER AS

SEMBLY, OPERATION, OR MAINTENANCE OF YOUR

EQUIPMENT.

WARNING

FAILURE TO COMPLY WITH ALL SAFETY AND OPERAT

ING INSTRUCTIONS CAN RESULT IN LOSS OF ENGINE

CONTROL, SERIOUS PERSONAL INJURY TO YOU AND/

OR BYSTANDERS, AND RISK OF EQUIPMENT AND

PROPERTY DAMAGE.

WARNING

READ ENTIRE OPERATING AND MAINTENANCE

INSTRUCTIONS FOR THIS PRODUCT AND THE

INSTRUCTIONS FOR THE EQUIPMENT THIS ENGINE

POWERS. FAILURE TO FOLLOW INSTRUCTIONS

COULD RESULT IN SERIOUS INJURY OR DEATH.

OPERATE THE ENGINE ACCORDING TO THE SAFETY

INSTRUCTIONS OUTLINED HERE AND INSERTED

THROUGHOUT THE TEXT. ANYONE WHO USES

THIS UNIT MUST READ THE INSTRUCTIONS AND BE

FAMILIAR WITH THE CONTROLS.

SAFETY DECALS:

Below are three of the warning decals attached to the auger. It is

important to read all safety precautions and locate the warning

labels before using this product.

WARNING!

Failure to read, understand and

follow all warnings and instruc-

tions listed could result in seri-

ous injury or death. Keep all body

extremities, loose clothing and

foreign objects clear of rotating

auger. Be sure auger is securely

attached to powerhead during

use. Never carry auger between

holes with the engine running.

This auger is not designed to be

utilized as an anchoring device.

Use this auger/powerhead as per

provided instructions only.

LBLAUGER R061909

Check for parts online at www.GetEskimo.com or call 800-345-6007 M-F 8-5 CDT

Operator's Manual

ESKIMO

Power Ice Auger

IMPORTANT SAFETY PRECAUTIONS:

• The ice blades are very sharp. Use extreme caution when

drilling a hole or replacing the blades. Put blade guard on

after each use.

• Do not carry the unit between holes with the engine running.

• The auger should not rotate when the engine is idling. If

it does rotate when engine is idling, contact an Eskimo-

authorized service center for instructions.

• Always keep hands, feet, hair and loose clothing away from

any moving parts on engine and auger.

• Do not allow children to operate this unit! Do not allow

adults to operate the unit without proper instruction.

• Do not operate any power equipment under the influence of

alcohol or drugs.

• Keep all screws, nuts and bolts tight.

• Engine should be turned off and cool, spark plug wire must be

removed from spark plug before any repairs are attempted.

• Temperature of muffler and nearby areas may exceed 150

(65

C). Avoid these areas.

• Never run engine indoors or in an enclosed area. Engine ex-

haust contains carbon monoxide, an odorless and deadly gas.

• If the auger becomes unturnable in a hole, turn engine off

and allow to cool before attempting to remove it manually.

ENGINE SAFETY PRECAUTIONS

Preventing Carbon Monoxide Poisoning

• Never try to ventilate engine exhaust indoors. Carbon

monoxide can reach dangerous levels very quickly.

• Never run engine outdoors where exhaust fumes may be

pulled into a building.

• Never run engine outdoors in a poorly ventilated area where

the exhaust fumes may be trapped and not easily taken away.

(Examples include: in a large hole or areas that are covered

by snow drifts.)

• Never run engine in an enclosed or partially enclosed area.

(Examples include: buildings that are enclosed on one or

more sides, inside shelters, garages or basements.)

WARNING

DO NOT ALTER/MODIFY ENGINE:

NEVER ALTER OR MODIFY THE ENGINE FROM THE

FACTORY. SERIOUS INJURY OR DEATH MAY OCCUR IF

ENGINE IS MODIFIED OR ALTERED.

WHEN WORKING ON OR REPLACING PARTS FOR THE

ENGINE OR PRODUCT, YOU MUST ALWAYS DISCON

NECT SPARK PLUG WIRE FROM THE SPARK PLUG AND

KEEP IT AWAY FROM THE SPARK PLUG.

ALWAYS WEAR HEARING PROTECTION WHILE OPER

ATING ENGINE.

PLEASE DO NOT START YOUR ICE AUGER UNTIL YOU

HAVE READ THE PREVIOUS SECTION OF THIS MANU

AL. IF YOU HAVE READ THESE, FOLLOW THE STEPS ON

THE NEXT PAGE TO START YOUR ICE AUGER.

NEVER STORE ENGINE WITH GAS IN THE TANK

INDOORS. FUEL AND FUEL VAPORS ARE HIGHLY

FLAMMABLE.

NEVER MIX FUEL AND OIL DIRECTLY IN ENGINE

GAS TANK. USE ONLY NONMETAL, PORTABLE FUEL

CONTAINERS APPROVED BY THE UNDERWRITER’S

LABORATORY U.L. OR THE AMERICAN SOCIETY FOR

TESTING & MATERIALS ASTM.

HANDLING AND FILLING THE ENGINE WITH FUEL

MUST ALWAYS BE DONE BY AN ADULT.

ALWAYS HANDLE FUEL IN A WELL VENTILATED AREA,

OUTDOORS, AWAY FROM FLAMES OR SPARKS.

WARNING

ENGINES GIVE OFF CARBON MONOXIDE, AN ODOR

LESS, COLORLESS, POISONOUS GAS. CARBON MON

OXIDE MAY BE PRESENT EVEN IF YOU DO NOT SMELL

OR SEE ANY ENGINE EXHAUST. BREATHING CAR

BON MONOXIDE CAN CAUSE NAUSEA, FAINTING OR

DEATH, IN ADDITION TO DROWSINESS, DIZZINESS

AND CONFUSION.

IF YOU EXPERIENCE ANY OF THESE SYMPTOMS, SEEK

FRESH AIR AND MEDICAL ATTENTION IMMEDIATELY.

START AND RUN ENGINE OUTDOORS. DO NOT START

OR RUN ENGINE IN AN ENCLOSED AREA, EVEN IF

DOORS OR WINDOWS ARE OPEN.

IMPORTANT

USING YOUR POWERHEAD AND/OR AUGER TO POWER OR

OTHERWISE UTILIZE ANY PRODUCT OR DEVICE MANUFAC

TURED BY ANY ENTITY OR INDIVIDUAL OTHER THAN ARDIS

AM, INC. WILL VOID YOUR WARRANTY AND WAIVE ANY AND

ALL CLAIMS FOR LIABILITY AGAINST ARDISAM, INC.

Check for parts online at www.GetEskimo.com or call 800-345-6007 M-F 8-5 CDT

Operator's Manual

ESKIMO

Power Ice Auger

• Always run the engine with the exhaust and muer pointed

in the direction away from the operator.

• Never point the exhaust muer towards anyone. People

should always be many feet away from the operation of the

engine and its attachments.

• Do not change the engine governor settings or over-speed

the engine.

• Stay away from rotating parts. Place protective covers over

rotating parts.

• Do not use engine around dry brush, cloth rags, or other

ammable materials.

• Always keep materials and debris clear of muer guard

and other hot engine parts.

• Never operate the engine without the muer guard in

place.

• Always make sure the exhaust pipe is free of foreign ob-

jects.

• The engine exhaust becomes very hot during operation.

Keep engine at least three feet away from buildings and

other equipment during operation.

• Wear appropriate clothing such as a long-sleeved shirt or

jacket. Also wear long trousers or slacks. Do not wear open

shoes, and never operate the machine with bare feet.

• Do not wear loose clothing or jewelry. They can get caught in

moving parts. Always keep hands, feet, hair and loose clothing

away from any moving parts on engine and machine.

Gasoline Fires and Handling Fuel Safely

Use extra care in handling gasoline and other fuels. They are

ammable and vapors are explosive.

• Never ll your fuel tank with fuel indoors. (Examples include:

basement, garage, barn, shed, house, porch, ice shelter, etc.)

• When storing extra fuel be sure that it is in an appropriate

container and away from any re hazards.

• Prevent re and explosion caused by static electric discharge.

Use only nonmetal, portable fuel containers approved by the

Underwriter’s Laboratory (U.L.) or the American Society for

Testing & Materials (ASTM).

• Always ll fuel tank outside in a well ventilated area. Never

fill your fuel tank with fuel indoors. (Examples include:

basement, garage, barn, shed, house, porch, etc.) Never

ll tank near appliances with pilot lights, heaters, or other

ignition sources. If the fuel has to be drained, this should be

done outdoors and with the proper equipment. Do not pour

fuel from fuel tank. The drained fuel should be stored in a

container specically designed for fuel storage or it should

be disposed of carefully.

• Never remove the fuel cap or add fuel with the engine

running. Stop engine and allow to cool before removing the

fuel cap/and or relling the engine.

• Do not smoke near or while handling engine fuel.

• Never drain fuel from engine in an enclosed area.

• Always wipe up excess (spilled) fuel from engine before

starting. Clean up spilled fuel immediately. If fuel is spilled,

do not start the engine but move product and fuel container

away from the area. Clean up spilled fuel and allow to

evaporate and dry after wiping and before starting.

• Allow fuel fumes/vapors to escape from the area before

starting engine.

• Test the fuel cap for proper installation before starting and

using engine.

• Always run the engine with fuel cap properly installed on

the engine.

• Never smoke while relling engine fuel tank.

• Do not store engine with fuel in fuel tank indoors. Fuel and

fuel vapors are highly explosive.

• During storage, tightly screw down fuel cap.

• Never pour fuel from engine fuel tank.

• Never siphon fuel by mouth to drain fuel tank.

• Always have an adult fill the fuel tank and never allow

children to ll the fuel tank.

• Never allow anyone under the inuence of drugs or alcohol

to ll the fuel tank.

• When storing gasoline or equipment with fuel in the tank,

store away from furnaces, stoves, water heaters or other

appliances that have a pilot light or other ignition source

because they can ignite gasoline vapors.

BURNS AND FIRES

The muer, muer guard and other parts of the engine

become extremely hot during the operation of the engine.

These parts remain extremely hot after the engine has stopped.

Prevention of Burns and Fires

• Never remove the muer guard from the engine.

• Never touch the muer guard because it is extremely hot

and will cause severe burns.

• Never touch parts of the engine that become hot after

operation.

• Always keep materials and debris away from muer guard

and other hot parts of the engine to avoid res.

Check for parts online at www.GetEskimo.com or call 800-345-6007 M-F 8-5 CDT

Operator's Manual

ESKIMO

Power Ice Auger

SERVICE

• Always stop the engine whenever you leave the equipment,

before cleaning, repairing or inspecting the unit. Engine

should be turned o and cool, spark plug wire must be

removed from spark plug before any repairs or adjustments

are attempted. Never make adjustments or repairs with the

engine (motor) running. Disconnect the spark plug wire,

and keep the wire away from the plug to prevent accidental

starting.

• Always wear eye protection when you make adjustments or

repairs.

• Keep all nuts & bolts tight and keep equipment in good

condition.

• Never tamper with safety devices. Check their proper

operation regularly.

• When servicing or repairing the engine, do not tip the engine

over or up unless specically instructed to do so in this manual.

Service and repair procedures can be done with the engine

in an upright position. Some procedures will be easier if the

engine is lifted on a raised platform or working surface.

• To reduce re hazard, keep engine free of debris build-up. Clean

up oil or fuel spillage. Allow engine to cool before storing.

• Stop and inspect the equipment if you strike an object.

Repair, if necessary, before restarting.

• Clean and replace safety and instruction decals as necessary.

• To guard against engine over-heating, always have engine

debris lter mounted and clean.

• Inspect engine before storage. When not in use, disconnect

spark plug lead and store indoors in a dry place locked or

otherwise inaccessible to children.

• Use only original equipment parts from Viper®, including all

nuts and bolts.

PREOPERATION

STEPS FOR WORKING ON ENGINE OR AUGER

1. Turn o engine switch.

2. Disconnect the spark plug wire from the spark plug.

3. Securely place the disconnected spark plug wire away from

the spark plug and any metal parts. This must always be done

or arcing may occur between spark plug wire and metal parts.

4. Replace or repair the part on the engine or auger.

5. Check all parts that were repaired, or removed during repair,

that they are secure and t correctly.

NOTE: All repair parts must come from the factory.

Never replace parts that are not specically designed

for the engine or auger.

6. Reconnect spark plug wire to the spark plug.

PREPARING ENGINE FOR STARTING

GAS AND OIL

Quality

To operate the engine, we recommend using Viper® brand 2-cycle

oil (P/N 300400) to ensure that the engine operates correctly

throughout the life of the engine. Viper® brand 2-cycle oil has

fuel stabilizer additive which helps to prevent gasoline from

oxidizing and gumming up the carburetor when the unit is not

in use for long periods of time. Use unleaded regular gas only.

It is best to use premium gasoline that has no ethanol content.

NOTE: Viper® oil can be purchased from our web site at

www.geteskimo.com.

Mixture

Run ice auger with a 50:1 ratio.

MIXING FUEL AND FILLING FUEL TANK

Mixing Fuel

1. Fuel must be mixed in a container outside in a well ventilated area.

2. Container must be directly contacting the ground when lling

with fuel.

3. Fill container about 1/4 full of recommended fuel.

4. Add recommended amount of oil and stabilizer to fuel.

5. Screw the container cap on tightly, and gently shake the

container to mix the oil/fuel.

6. Remove the cap, and nish lling the container.

7. Wipe away all spilled oil and gas, and allow to evaporate

before transport.

Filling Fuel Tank

1. Always ll the fuel tank with the engine o, and completely

cooled to ambient temperature.

2. Always ll the tank outside, in a well ventilated area, away

from open ame and sparks.

3. Clean away any debris from around the fuel cap.

4. Slowly open the fuel cap to allow pressure to slowly release,

do not set the cap on a dirty surface.

5. Add fuel to fuel tank with care, as to prevent spilling any gas.

GAS OIL RATIO

1 gallon 2.5 ounces 50:1

2 gallons 5 ounces 50:1

5 gallons 13 ounces 50:1

IMPORTANT

THIS ENGINE USES A GAS/OIL MIXTURE. DO NOT RUN ON

STRAIGHT GAS ONLY, ENGINE DAMAGE WILL RESULT.

Check for parts online at www.GetEskimo.com or call 800-345-6007 M-F 8-5 CDT

Operator's Manual

ESKIMO

Power Ice Auger

CAUTION

AVOID INJURY! ALWAYS HANDLE FUEL IN A WELL

VENTILATED AREA, OUTDOORS, AWAY FROM FLAMES

OR SPARKS.

AVOID INJURY! DO NOT START ENGINE IF FUEL IS

SPILLED. WIPE OFF EXCESS FUEL AND ALLOW TO DRY.

REMOVE ENGINE FROM AREA TO AVOID SPARKS.

WARNING

AVOID INJURY! MAKE SURE THE UNIT IS IN A STABLE

POSITION BEFORE PULLING THE STARTER HANDLE.

AVOID INJURY! WHILE STARTING ENGINE, ENSURE

THAT THROTTLE CONTROL IS NOT ENGAGED.

CAUTION

AVOID INJURY! IF AUGER IS MOUNTED TO ENGINE,

ALL SAFETY GUARDS MUST BE SECURELY FASTENED

TO AVOID SERIOUS INJURY.

AVOID INJURY! STARTER ROPE CAN CAUSE AN UNAN

TICIPATED JERK TOWARDS ENGINE. PLEASE FOLLOW

INSTRUCTIONS TO AVOID INJURY.

AVOID INJURY! IF ENGINE FAILS TO START AFTER TRY

ING STARTING PROCEDURES, PLEASE CONTACT OUR

CUSTOMER SERVICE DEPARTMENT AT 8003456007

OR VISIT WWW.GETESKIMO.COM.

AVOID INJURY! NEVER LEAVE ENGINE RUNNING

WHILE UNATTENDED. TURN OFF AFTER EVERY USE.

AVOID INJURY! NEVER CARRY POWERHEAD AND AU

GER BETWEEN HOLES WHILE ENGINE IS RUNNING.

6. Do not ll tank completely full, allow for fuel to expand.

7. Screw the fuel cap back on until tight. Wipe away any spilled

fuel, and allow the engine to dry o before attempting to

start the engine.

OPERATION

1. Drill holes without placing downforce on the auger. Allow the

weight of the auger to do the work itself. Using force will add

unnecessary wear to the unit.

2. The clutch will transfer maximum power after two hours of

operation. Some slippage may occur during the break-in peri-

od. Keep the clutch and clutch drum free of moisture and oil.

3. Never run the engine in an enclosed area or indoors. Exhaust

fumes are deadly.

4. Do not use the ice auger for anything orther than drilling

through ice.

5. Always use the blade protector when not in use. This prevents

accidental contact with the blades, and keeps the blades and

point protected.

6. To attach the auger to the output shaft of the unit, align the

holes on the shaft and the auger, and tighten the bolt with

the supplied Allen wrench. Always check that this bolt is tight,

and ush with the auger stem before use.

IMPORTANT NOTE:

The A-weighted emission sound pressure level has been

measured at 100 dB L

PA.

The A-weighted sound power

level emitted has been measured at 106.5 dB L

WA.

The total

vibration value for the F1™ power ice auger was measured at

31.3 m/s

Cold Starting Instructions:

Follow these instructions whenever starting an engine that is

cold, cooled o from prior use, rst time operating, or when unit

is run dry of fuel.

1. Turn on/o switch to the “ON” position.

2. Switch the choke lever to the “CHOKE” position.

3. Push the primer bulb until fuel enters the primer line,

allow the bulb to fully return each time.

4. Once fuel is in the primer line, push bulb additional 2-3 times.

5. Pull recoil slowly until recoil has resistance, then using swift

arm length pulls, pull the recoil 2-3 times, allowing it to retract

slowly each time. DO NOT allow the recoil to retract on its

own, as it may snap back quickly and cause injury.

6. If unit does not start, repeat step 4 and 5.

7. Once engine starts, let idle until warm, then switch the choke

lever to the “RUN” position.

Warm Starting Instructions:

1. Turn on/o switch to the “ON” position.

2. Ensure the choke lever is in the “RUN” position.

3. Pull recoil slowly until recoil has resistance, then using swift

arm-length pulls, pull the recoil 2-3 times, allowing it to retract

slowly each time. DO NOT allow the recoil to retract on its

own, as it may snap back quickly and cause injury.

4. If unit does not start, use cold starting instructions.

Check for parts online at www.GetEskimo.com or call 800-345-6007 M-F 8-5 CDT

Operator's Manual

ESKIMO

Power Ice Auger

MAINTENANCE AND STORAGE

AUGER MAINTENANCE

1. The gear case has 4 ounces of lithium grease installed at the

factory. It is recommended that once a year the gear case be

split and the grease level checked. Add grease only if level of

grease is below top of the gears. DO NOT OVERFILL.

2. Keep all screws, nuts, and bolts tight.

3. For cold weather operation, store the unit in a cool environ-

ment. Transferring the unit from a warm to a cold place can

cause the build up of harmful condensation.

4. Always replace blade protector when power auger is not in use.

5. If blade performance decreases, turn unit o and disconnect

spark plug wire. Carefully inspect cutting edge of blades for

any nicks or shiny areas. If blades show any of these signs, they

need to be resharpened or replaced.

ENGINE MAINTENANCE

Please read the maintenance schedule and observe these

recommendations to extend the life of your engine.

Good maintenance is essential for safe, economical, and trou-

ble-free operation. It will also help reduce air pollution. To help

you properly care for your engine, the following pages include

a maintenance schedule, routine inspection procedures, and

simple maintenance procedures using basic hand tools.

Other service tasks that are more difficult, or require special

tools, are best handled by professionals and are normally

performed by a technician or other qualified mechanic.

MAINTENANCE ITEM

BEFORE

EVERY USE

10 HOURS 50 HOURS SEASONALLY

Check fasteners for tightness (Nuts, Bolts, Screws) X

Check blades and point X

Clean debris from unit X

Check air lter X

Clean air lter X X

Check sparkplug X

Replace sparkplug X

Replace fuel lter X

Check fuel lines X

Check gaskets X

Maintenance, replacement or repair of the emissions con-

trol devices and systems may be performed by any non-

road engine repair establishment or individuals. However,

all authorized warranty repairs must be handled by an

authorized service center.

The maintenance schedule applies to normal operating

conditions. If you operate your engine under unusual con-

ditions, such as sustained high-load or high-temperature

operation, or use in unusually wet or dusty conditions, consult

your servicing dealer for recommendations applicable to your

individual needs and use.

Check Fasteners for Tightness

Before each use, always ensure that all bolts and screws are

properly tightened down. Failure to do so could result in loss of

auger through the ice, burns, and reduced engine performance.

Check Blades and Point

Check blades for nicks or shiny areas along the cutting edge,

if these signs are present, it is time to replace the blades. Check

ice point for nicks and dull edges.

Clean Debris from Unit

• For the engine to cool itself, it is important that the cooling

fins are kept free of debris.

• Keep the flywheel free from debris to allow sufficient air flow

across the engine fins.

• Use either compressed air, a vacuum, or a brush to clean debris

off of components.

• If excessive oil builds up on the cooling fins, wipe off with a

clean rag.

Check for parts online at www.GetEskimo.com or call 800-345-6007 M-F 8-5 CDT

Operator's Manual

ESKIMO

Power Ice Auger

CAUTION

AVOID INJURY! DO NOT ATTEMPT TO START THE EN

GINE USING STARTING FLUID.

AVOID INJURY! DO NOT SPRAY FLAMMABLE LIQUIDS

OR VAPORS INTO AIR CLEANER, CARBURETOR OR

SPARK PLUG CHAMBER.

AVOID INJURY! DO NOT REMOVE SPARK PLUG AND

PULL STARTER ROPE. FLAMMABLE FUEL CAN SPRAY

OUT & IGNITE FROM A SPARK FROM SPARK PLUG.

CAUTION

TO PREVENT ACCIDENTAL STARTING:

AVOID INJURY! ENGINE MUST BE TURNED OFF AND

COOL, AND SPARK PLUG WIRE MUST BE REMOVED

FROM SPARK PLUG BEFORE CHECKING AND ADJUST

ING ENGINE OR EQUIPMENT.

AVOID INJURY! TEMPERATURE OF MUFFLER AND

NEARBY AREAS MAY EXCEED 150º F 65º C. AVOID

THESE AREAS.

AVOID INJURY! CHECK AUGER OFTEN FOR LOOSE NUTS

AND BOLTS. KEEP THESE ITEMS TIGHTENED.

AVOID INJURY! NEVER STORE ENGINE WITH FUEL IN

THE TANK INSIDE A BUILDING. POTENTIAL SPARKS

MAY BE PRESENT FOR IGNITION OF FUEL AND FUEL

VAPORS.

AVOID INJURY! AN ADULT MUST ALWAYS DO MAINTE

NANCE AND REPAIR ON ENGINE AND AUGER.

AVOID INJURY! ENGINE MUST BE SHUTOFF, COOL, AND

SPARK PLUG WIRE REMOVED BEFORE ANY REPAIR OR

MAINTENANCE CAN BE DONE.

CAUTION

AVOID INJURY! TO AVOID INJURY OR DEATH, NEVER

SIPHON FUEL BY MOUTH.

AVOID INJURY! NEVER STORE ICE AUGER WITH FUEL

IN THE GAS TANK INSIDE AN ENCLOSED AREA OR

BUILDING.

Check Air Filter

• It is recommended that the air filter be checked before each use.

• The air filter element should be clean and free from particles

or debris for proper engine performance and to protect the

engine from damage.

• If the filter is dirty, cleaning will be needed, and if necessary

the filter will need to be replaced.

Clean Air Filter

1. Wash air filter in warm water with a mild detergent until dirt

and debris is removed. Press filter while washing, do not twist.

2. Rinse with warm water until all detergent residue is removed.

3. Dry filter by pressing with cloth or towel, and allow to air dry

overnight.

4. Re-install filter into filter housing, and check for proper fit.

Check Sparkplug

1. Disconnect ignition coil wire from sparkplug and clean debris

from around plug

2. Remove the plug and check for the following: pitted electrode,

burned electrode, cracked porcelain, or carbon deposits

around electrode.

3. If any of the previous signs are present, replace sparkplug.

The sparkplug used by your engine is a Torch L7RTC gapped

to 0.024 inches (0.60mm).

4. To re-install the sparkplug, torque sparkplug to 7.2 - 8.7 ft-lbs.

Replace Sparkplug

• Replace with a Torch L7RTC sparkplug gapped to 0.024 inches

(0.60mm).

• Torque to 7.2 - 8.7 ft-lbs.

NOTE: A loose sparkplug may overheat and damage engine.

An over-tightened sparkplug may damage threads in the

cylinder head.

Replace Fuel Filter

Depending on the quality of fuel used, the fuel filter may need

more frequent replacement. To replace the fuel filter:

1. Ensure the tank has been drained of all fuel.

2. Using a long set of forceps, or a bent piece of wire, pull the

fuel line out through the ll spout.

3. Pull the old lter o of the fuel line, and press the new lter

on all the way.

4. Reinsert the line and lter back into the tank, and ensure it can

move around with the changing position of the unit. It should

be farthest from the tank spout to ensure proper movement.

Check for parts online at www.GetEskimo.com or call 800-345-6007 M-F 8-5 CDT

Operator's Manual

ESKIMO

Power Ice Auger

TRANSPORTING YOUR ICE AUGER

1. Never transport engine inside an enclosed space or vehicle.

Fuel or fuel vapors may ignite causing serious injury or death.

2. If fuel is present in the fuel tank, transport in an open vehicle

in an upright position with the gas cap facing upwards.

3. If an enclosed vehicle must be used, remove gas into an ap-

proved red fuel container. DO NOT siphon by mouth.

4. Run engine to use up the fuel in the carburetor and fuel tank.

Always run engine in a well ventilated area.

5. Wipe away any spilled fuel from engine and ice auger. Allow

to dry.

LONGTERM STORAGE

• If your ice auger will not be ran for more than one month,

prepare it for long-term storage.

Steps for Long Term Storage

1. Add fuel stabilizer according to manufacturer’s instructions.

2. Run engine for 10-15 minutes to ensure that the stabilizer

reaches the carburetor.

3. Remove the remainder of the fuel from the gas tank into an

approved fuel container.

4. Remove auger from powerhead and apply a thin layer of

grease to the output shaft.

5. Store auger and powerhead (engine) in a vertical position.

6. Remove all debris from auger and powerhead (engine).

7. Attach blade protector to bottom of auger.

SERVICE, TROUBLESHOOTING

AND REPAIR

SERVICE INFORMATION

At Ardisam, we build quality and durability into the design of

our products; but no amount of careful design by us, and careful

maintenance by you, can guarantee a repair-free life for your

unit. Most repairs will be minor, and easily xed by following the

suggestions in the troubleshooting guide in this section.

The guide will help you pinpoint the causes of common problems

and identify remedies.

For more complicated repairs, you may want to rely on your

retailer or an authorized repair center (contact your retailer for

a list of authorized mechanics in your area). A parts breakdown

can be found on our website, www.geteskimo.com.

CAUTION

AVOID INJURY! AUGER BLADES AND POINT ARE EX

TREMELY SHARP. USE CAUTION WHEN REMOVING

AND REPLACING.

PRACTICE SAFETY AT ALL TIMES. ENGINE MUST BE

TURNED OFF AND ALLOWED TO COOL, AND SPARK

PLUG WIRE MUST BE DISCONNECTED BEFORE AT

TEMPTING ANY MAINTENANCE OR REPAIR.

auger shaft

nut

point

holder

bolt

bolt hole

FIGURE 1

We will always be glad to answer any questions you have, or

help you nd suitable assistance. To order parts or inquire about

warranty, call or write us at the address found on the next page,

under the section “ordering repair parts”.

ICE POINT REPLACEMENT SEE FIGURE 1 ABOVE

1. Remove blade protector and both blades.

2. Remove nut and retaining bolt from point.

3. Using a locking pliers, grasp point and pull out. If holder

doesn’t come out with the point, remove with pliers.

4. With locking pliers, push in new point and holder aligning

bolt hole in point with holes in auger shaft. DO NOT damage

end of point.

NOTE: When installing holder in auger shaft, edges of holder

may shave o.

5. Insert retaining bolt and tighten with nut.

6. Re-attach both blades and put blade protector back on.

Check for parts online at www.GetEskimo.com or call 800-345-6007 M-F 8-5 CDT

Operator's Manual

ESKIMO

Power Ice Auger

ORDERING REPAIR PARTS

Parts may be obtained from the store where your auger was

purchased or direct from the factory. To order from the factory,

call, e-mail, or order online at www.geteskimo.com:

Eskimo®

A Division of Ardisam, Inc.

1-800-345-6007

E-mail: info@geteskimo.com

Please include the part numbers, part description, quantity,

model number and serial number.

TROUBLESHOOTING:

PROBLEM POSSIBLE CAUSE REMEDY/ACTION

Engine will not start 1. Power switch o 1. Flip switch to ON position

2. Spark plug wire disconnected 2. Connect spark plug wire to spark plug

3. Out of fuel 3. Refuel

4. Spark plug wet, faulty or

improperly gapped

4. Clean, replace or gap spark plug

Engine runs rough, oods during

operation

1. Dirty air lter 1. Clean or replace air lter

2. Choke partially engaged 2. Turn o choke

3. Carburetor out of adjustment 3. Take to authorized service center.

Engine is hard to start 1. Stale fuel 1. Drain old fuel and replace with fresh. Always

use gas stabilizer

2. Spark plug wire loose 2. Make sure spark wire is securely attached to

spark plug

3. Dirty carburetor 3. Clean carburetor, use gas stabilizer, new gas can

4. Faulty ignition coil 4. Take to authorized service center.

Engine misses or lacks power 1. Clogged fuel lter 1. Replace lter

2. Clogged air lter 2. Remove and clean or replace lter

3. Faulty ignition coil 3. Take to authorized service center.

Auger turns at idle 1. Idle speed too high 1. Adjust idle speed lower

2. Broken clutch spring 2. Replace spring

Auger turns, but has no power 1. Choke on 1. Turn o choke after engine is running

2. Carburetor out of adjustment 2. Take to authorized service center.

3. Broken transmission 3. Take to authorized service center.

4. Worn clutch shoes 4. Replace clutch shoes and spring

Auger jumps on ice 1. Blades damaged or sharpened

incorrectly

1. Replace blades

Auger cuts slowly 1. Dull blades 1. Replace blades

2. Damaged point 2. Replace point

Contact service provider if above remedies fail, or visit our website at www.geteskimo.com for additional frequently asked

questions.

Check for parts online at www.GetEskimo.com or call 800-345-6007 M-F 8-5 CDT

Operator's Manual

ESKIMO

Power Ice Auger

ESKIMO POWER ICE AUGERS

Warranty Terms and Conditions

PRODUCT WARRANTY: 5YEAR LIMITED WARRANTY

Ardisam, Inc. (Ardisam), a manufacturing company, warrants this product to be free from defects in the material or workmanship

for a period of ve years from the date of purchase. If there is insucient evidence of the purchase date, the eective date of this

warranty will begin on the augers date of manufacture. During the ve-year warranty of this product, Ardisam will furnish, at their

discretion, parts and labor to correct any defect caused by faulty material or workmanship. In no event shall recovery of any kind be

greater than the amount of the purchase price of the product sold. Ardisam reserves the right to inspect any incoming units returned

under warranty to determine if warranty applies before performing any warranty related work (including parts and component). Any

unit used in a commercial application, or producing income is covered for a period of 90 days after purchase. This warranty applies

to the original owner with a proof of purchase and is not transferable. For the warranty to be valid, the product must be registered

online, or the warranty card must be lled out and received by Ardisam, within 30 days of purchase. This warranty excludes augers

that sustain damage or defects due to normal wear, wear items such as cables, clutch shoes, blade protector bungee, blades, and

ice points, routine maintenance items such as lter elements, o-rings, seals, lubricants, and tune-ups, running the engine with non-

mixed (no oil) fuel, or without proper mix ratio, using the power auger for a purpose other than that for which it was designed and

manufactured, using the power auger in violation of local codes, ordinances and good trade practices. *These warranties apply only

to products which have not been subjected to negligent use, abuse, misuse, overload, improper installation, alteration, accident,

acts of God (or other events beyond Ardisam’s control), vandalism, unauthorized parts, failure to use proper fuel and oil, improper

maintenance, or if repairs have been performed at a non-authorized service facility. These warranties shall not cover damage from

normal wear and tear, normal maintenance parts and services, nor improper installation, operation, storage, or maintenance;

nor operating the equipment above recommended maximums as stated in this manual. These warranties supersede all other

warranties either expressed or implied and all other obligations or liabilities on the part of Ardisam. Ardisam, does not assume, and

does not authorize any other person to assume for Ardisam, any liability in connection with the sale of Ardisam products. To be at

“No Charge,” warranty work must be sent directly to and performed by Ardisam or an Ardisam Authorized Warranty

Service Facility. To obtain warranty service and/or replacement instructions, contact the Ardisam Customer Service Department

at 800-345-6007. If you choose to ship your product to Ardisam for warranty repair, you must rst have prior approval from Ardisam

by calling the Ardisam Customer Service Department for a return material authorization number (RMA#). Under these circumstances,

all items must be shipped prepaid. Ardisam will at no charge, repair or replace, at the discretion of Ardisam, any defective part

which falls under the conditions stated above. Ardisam retains the right to change models, specications and price without notice.

Ardisam shall not be obligated to ship any repair or replacement product to any location outside of the United States of America or

Canada. Some states and countries do not allow the limitations on how long an implied warranty lasts, or the exclusion or limitation

of incidental or consequential damages, so the above limitation may not apply to you. This warranty gives you specic legal rights,

and you may also have other rights which vary from state to state and country to country.

ESKIMO®

A Division of Ardisam, Inc.

1160 Eighth Avenue; P.O. Box 666

Cumberland, Wisconsin 54829

1-800-345-6007 · Fax (715) 822-4180

E-mail: [email protected]om

IMPORTANT

USING YOUR POWERHEAD AND/OR AUGER TO POWER OR OTHERWISE UTILIZE ANY PRODUCT OR DEVICE MANUFACTURED BY

ANY ENTITY OR INDIVIDUAL OTHER THAN ARDISAM, INC. WILL VOID YOUR WARRANTY AND WAIVE ANY AND ALL CLAIMS FOR

LIABILITY AGAINST ARDISAM, INC.

Check for parts online at www.GetEskimo.com or call 800-345-6007 M-F 8-5 CDT

Operator's Manual

ESKIMO

Power Ice Auger

Warranty Terms and Conditions

ARDISAM LIMITED 5 YEAR VIPER ENGINE WARRANTY

FOR ENGINES LESS THAN 79CC’s MANUFACTURED AFTER 4/1/2016

Ardisam, Inc. (Ardisam) warrants this engine under a ve-year limited warranty to be free from defects in the material or

workmanship or both for a period not exceeding sixty consecutive months from the date of original purchase by the rst retail

consumer or rst commercial end user. “Consumer use,” means personal recreational use by a retail consumer. “Commercial use,“

or “commercial application,“ means all other uses, including use for commercial, income producing or rental purposes. Once

a product has experienced commercial use, it shall thereafter be considered as a commercial use product for the purpose of

this warranty. This warranty applies to the original owner that provides a proof of purchase. This warranty is not transferable.

The warranty period begins on the date of purchase by the rst retail consumer or commercial end user, and continues for the

sixty month consecutive period thereafter. Any unit used in a commercial application is covered for a period of 90 days after

purchase by the rst commercial end user. For the warranty to be valid, the product must be registered online within 30 days of

purchase, or the warranty card must be lled out and received by Ardisam within 30 days of purchase. Ardisam shall not be obli-

gated for transportation charges that result from repair or replacement under the terms of this warranty. Transportation charges

are the sole responsibility of the purchaser.

This warranty excludes parts that are worn or damaged due to normal wear such as spark plugs, recoil ropes, fuel lters, and

bearings. Routine maintenance items such as lter elements, O-rings, seals, lubricants, and tune-ups are also excluded.

Natural fading or peeling from normal deterioration due to weather elements, sea water, and chemicals is also excluded.

Non catalytic muers will be warrantied for one year. For all catalytic muers refer to the emissions control warranty

contained in the retail package.

This limited warranty applies to defects in the material or workmanship of the engine only. This warranty does not apply to the

product to which the engine is mounted. This warranty policy applies only to engines which have not been subjected to misuse

including but not limited to operating engine with insucient, contaminated, or incorrect grade of oil, using gasoline with

ethanol greater than 10%, contaminated gasoline, dirt ingestion due to improper air lter maintenance or improper installa-

tion, excessive vibration causing loose hardware, unbalanced items attached to the crankshaft, uses other than those indicated

in the product manual, alteration, accident, use of unauthorized parts, failure to perform periodic maintenance as specied in

engine manual, normal wear and tear, use of unauthorized parts or repairs performed at unauthorized service centers. Parts

applied to the external engine like clutches, pulleys, belt engagement items are subject to the warranty of the product to which

the engine is mounted. Failure resulting from obstructing airow to the engine such as dirt, grass, rodent nests that cause

overheating is excluded. All parts specied in the “Emissions Control Warranty” contained in this manual will follow the terms of

that agreement and are not included as part of this warranty. There is no other express warranty. Implied warranties, including

those of merchantability and tness for a particular purpose, are limited to one year from purchase, or to the extent permitted

by law. All other implied warranties are excluded. Liability for incidental or consequential damages are excluded to the extent

exclusion is permitted by law. Ardisam does not assume, and does not authorize any other person to assume for Ardisam,

any liability in connection with the sale of Ardisam products. To be at “No Charge,” warranty work must be sent directly to and

performed by Ardisam or an Ardisam Authorized Warranty Service Facility. To obtain warranty service and/or replacement

instructions, contact the Ardisam Customer Service Department at 800-345-6007. If you choose to ship your product to Ardisam

for warranty repair, you must rst have prior approval from Ardisam by calling the Ardisam Customer Service Department for a

return material authorization number (RMA#). Under these circumstances, all items must be shipped prepaid. Ardisam will, in its

discretion, at no charge, repair or replace any defective part to which this warranty applies. Ardisam retains the right to change

models, specications and price without notice. Ardisam shall not be obligated to ship any repair or replacement product to

any location outside of the United States of America or Canada. Some states and countries do not allow the limitations on how

long an implied warranty lasts, or the exclusion or limitation of incidental or consequential damages, so the above limitation

may not apply to you. This warranty gives you specic legal rights, and you may also have other rights which vary from state to

state and country to country.

Check for parts online at www.GetEskimo.com or call 800-345-6007 M-F 8-5 CDT

Operator's Manual

ESKIMO

Power Ice Auger

II. EMISSION CONTROL SYSTEM WARRANTY

Emission Control System Warranty (ECS Warranty) for equipment

using small o-road engines:

(1) Applicability: This warranty shall apply to equipment that uses

small o-road engines. The ECS Warranty Period shall begin

on the date the new engine or equipment is purchased by/

delivered to its original, end-use purchaser/owner and shall

continue for 24 consecutive months thereafter.

(2) General Emissions Warranty Coverage: Ardisam warrants to

the original, end-use purchaser/owner of the new engine or

equipment and to each subsequent purchaser/owner that each

of its engines is...

(a) Designed, built and equipped so as to conform with all

applicable regulations adopted by the EPA pursuant to

their respective authority, and

FEDERAL EMISSION CONTROL

WARRANTY STATEMENT

YOUR WARRANTY RIGHTS AND OBLIGATIONS

The United States Environmental Protection Agency (EPA), togeth-

er with Ardisam, Inc. (Ardisam), are pleased to explain the Emission

Control System Warranty on your small o-road engine (SORE). New

small o-road engines must be designed, built and equipped to meet

stringent anti-smog standards the federal government. Ardisam will

warrant the emission control system on your engine for the periods of

time listed below provided there has been no abuse, neglect, modi-

cation or improper maintenance of your engine.

The emission control system includes all components whose failure

would increase the emissions of any regulated pollutant. These com-

ponents are listed in the emission-related parts list located in a subse-

quent section of this emissions warranty statement. Ardisam will repair

your engine at no cost to you for diagnosis, replacement parts and la-

bor, should a warrantable condition occur.

MANUFACTURER’S WARRANTY COVERAGE:

The emission control system is warranted for two years. If, during such

warranty period, any emission-related part on your engine is found to

be defective in materials or workmanship, repairs or replacement will

be performed by a Ardisam Authorized Warranty Service Facility.

PURCHASER’S/OWNER’S WARRANTY RESPONSIBILITIES:

As the SORE purchaser/owner, you are responsible for the completion

of all required maintenance as listed in your factory supplied manu-

al(s). For warranty purposes, Ardisam recommends that you retain all

receipts covering maintenance on your SORE. However, Ardisam can-

not deny warranty solely because of the lack of receipts or for your

failure to ensure the completion of all scheduled maintenance.

As the SORE purchaser/owner, you should, however, be aware that

Ardisam may deny any and/or all warranty coverage or responsibili-

ty if your SORE or a part/component thereof, has failed due to abuse,

neglect, improper maintenance or modications, or the use of coun-

terfeit and/or “grey market” parts not made, supplied or approved by

Ardisam.

You are responsible for presenting your SORE to an Ardisam Autho-

rized Warranty Service Facility as soon as a problem occurs. The war-

ranty repairs should be completed in a reasonable amount of time, not

to exceed 30 days.

Warranty service can be arranged by contacting either your selling

dealer or a Ardisam Authorized Warranty Service Facility. To locate the

Ardisam Authorized Warranty Service Facility nearest you, call our free

number:

Ardisam Authorized Warranty Service Facility:

800-345-6007

IMPORTANT NOTE: This warranty statement explains your rights and

obligations under the Emission Control System Warranty (ECS Warran-

ty), which is provided to you by Ardisam pursuant to federal law. See also

the Ardisam “Product Warranty” (non-emission warranties), which is en-

closed herewith on a separate sheet or located in additional materials

accompanying this product. The ECS Warranty applies only to the

emission control system of your new engine. If there is any conict in

terms between the ECS Warranty and the Ardisam Warranty, the ECS

Warranty shall apply except in circumstances where the Ardisam War-

ranty may provide a longer warranty period. Both the ECS Warranty

and the Ardisam Warranty describe important rights and obligations

with respect to your new engine.

Warranty service can be performed only by an Ardisam Authorized

Warranty Service Facility. When requesting warranty service, evidence

must be presented showing the date of the sale to the original purchas-

er/owner. The purchaser/owner shall be responsible for any expenses

or other charges incurred for service calls and/or transportation of

the product to/from the inspection or repair facilities. The purchaser/

owner shall also be responsible for any and/or all damages or losses

incurred while the engine is being transported/shipped for inspection

or warranty repairs.

IF YOU HAVE ANY QUESTIONS REGARDING YOUR WARRANTY

RIGHTS AND RESPONSIBILITIES, YOU SHOULD CONTACT ARDISAM

AT THE FOLLOWING ADDRESS:

Ardisam, Inc.

1160 Eighth Avenue; P.O. Box 666

Cumberland, Wisconsin 54829

800-345-6007 · Fax (715) 822-4180

LIMITED 2YEAR EMISSIONS CONTROL WARRANTY

Check for parts online at www.GetEskimo.com or call 800-345-6007 M-F 8-5 CDT

Operator's Manual

ESKIMO

Power Ice Auger

(9) Unapproved, add-on, modied, counterfeit and/or “grey

market” parts may not be used to modify or repair a Ardisam

engine. Such use voids this ECS Warranty and shall be sucient

grounds for disallowing an ECS Warranty claim. Ardisam shall

not be held liable hereunder for failures of any warranted parts

of a Ardisam engine caused by the use of such an unapproved,

add-on, modied, counterfeit and/or “grey market” part.

EMISSION-RELATED PARTS INCLUDE THE FOLLOWING

(IF EQUIPPED):

(1) Fuel Metering System

(i) Carburetor and internal parts (and/or pressure regulator or

fuel injection system).

(ii) Air/fuel ratio feedback and control system.

(iii) Cold start enrichment system.

(iv) Fuel Tank.

(2) Air Induction System

(i) Controlled hot air intake system.

(ii) Intake manifold.

(iii) Air lter.

(3) Ignition System

(i) Spark Plugs.

(ii) Magneto or electronic ignition system.

(iii) Spark advance/retard system.

(4) Exhaust Gas Recirculation (EGR) System

(i) EGR valve body, and carburetor spacer if applicable.

(ii) EGR rate feedback and control system.

(5) Air Injection System

(i) Air pump or pulse valve.

(ii) Valves aecting distribution of ow.

(iii) Distribution manifold.

(6) Catalyst or Thermal Reactor System

(i) Catalytic converter.

(ii) Thermal reactor.

(iii) Exhaust manifold.

(7) Particulate Controls

(i) Traps, lters, precipitators, and any other device used to

capture particulate emissions.

(8) Miscellaneous Items Used in Above Systems

(i) Electronic controls.

(ii) Vacuum, temperature, and time sensitive valves and

switches.

(iii) Hoses, belts, connectors, and assemblies.

(b) Free from defects in materials and workmanship which,

at any time during the ECS Warranty Period, may cause a

warranted emissions-related part to fail to be identical in

all material respects to the part as described in the engine

manufacturer’s application for certication.

The ECS Warranty only pertains to emissions-related parts on your

engine, as follows:

(1) Any warranted, emissions-related parts that are not

scheduled for replacement as required maintenance in the

Maintenance Schedule (located in the section of the Manual(s)

pertaining to maintenance) shall be warranted for the ECS

Warranty Period. If any such part fails during the ECS Warranty

Period, it shall be repaired or replaced by Ardisam according to

Subsection (4) below. Any such part repaired or replaced under

the ECS Warranty shall be warranted for the remainder of the

ECS Warranty Period.

(2) Any warranted, emissions-related part that is scheduled

only for regular inspection as specied in the Maintenance

Schedule (located in the section of the Manual(s) pertaining to

maintenance) shall be warranted for the ECS Warranty Period. A

statement in such written instructions to the eect of “repair or

replace as necessary” shall not reduce the ECS Warranty Period.

Any such part repaired or replaced under the ECS Warranty shall

be warranted for the remainder of the ECS Warranty Period.

(3) Any warranted, emissions-related part that is scheduled

for replacement as required maintenance in the Maintenance

Schedule (located in the section of the Manual(s) pertaining to

maintenance) shall be warranted for the period of time prior to

the rst scheduled replacement point for that part. If the part

fails prior to the rst scheduled replacement, the part shall be

repaired or replaced by Ardisam according to Subsection (4)

below. Any such emissions-related part repaired or replaced

under the ECS Warranty shall be warranted for the remainder

of the ECS Warranty Period prior to the rst scheduled

replacement point for such emissions-related part.

(4) Repair or replacement of any warranted, emissions-related part

under this ECS Warranty shall be performed at no charge to the

owner at a Ardisam Authorized Warranty Service Facility.

(5) When the engine is inspected by a Ardisam Authorized

Warranty Service Facility, the owner shall not be held

responsible for diagnostic costs if the repair is deemed

warrantable.

(6) Ardisam shall be liable for damages to other original engine

components or approved modications proximately caused by

a failure under warranty of any emission-related part covered by

the ECS Warranty.

(7) Throughout the ECS Warranty Period, Ardisam shall maintain a

supply of warranted emission-related parts sucient to meet

the expected demand for such emission-related parts.

(8) Any Ardisam authorized and approved emission-related

replacement part may be used in the performance of any ECS

Warranty maintenance or repairs and will be provided without

charge to the purchaser/owner. Such use shall not reduce

Ardisam’s ECS Warranty obligations.

Eskimo™, Division of Ardisam, Inc.

1160 8th Avenue, PO Box 666

Cumberland, WI 54829

800-345-6007

Fax 715-822-2223

E-mail: info@geteskimo.com

Check for parts online at www.GetEskimo.com or call 800-345-6007 M-F 8-5 CDT

28284

ECN #11656

RÉV1 05/24/2017

Visitez-nous au

www.GetEskimo.com

GAS/OIL

RATIO

50:1

Manuel de l’opérateur

Mode d’emploi original

F1 ROCKET

™

Tarière à glace à moteur 33cc

F1 ROCKET

™

TARIÈRE À GLACE À MOTEUR 33CC

Voir les pièces détachées en ligne à www.geteskimo.com ou composer le 800-345-6007 L-V 8h-17h HNC

Manuel de l’opérateur

Tarière à glace à moteur ESKIMO

INTRODUCTION

Merci d’avoir acheté une tarière à glace à moteur Eskimo® de Ardisam, Inc. Nous avons travaillé pour nous assurer que la tarière à

glace réponde à des standards élevés de fonctionnalité et de durabilité. Avec des soins adéquats, votre tarière à glace vous orira

plusieurs années de service. Veuillez prendre le temps de lire ce manuel attentivement an d’apprendre à opérer et à entretenir

correctement votre tarière à glace. Nous vous félicitons pour votre investissement dans la qualité. Conserver ces instructions pour

consultation future. Ardisam, Inc. réserve le droit de changer ou de modier ce manuel sans préavis.

TABLE DES MATIÈRES

Enregistrement ............................................................................................................................................................................................................................................................ 18

Avertissements et mesures de sécurité ........................................................................................................................................................................................................19-22

Pré-opération .........................................................................................................................................................................................................................................................22-23

Utilisation ................................................................................................................................................................................................................................................................23-24

Entretien et entreposage ...................................................................................................................................................................................................................................24-26

Service, Dépannage et Réparation ................................................................................................................................................................................................................26-27

Garantie ...................................................................................................................................................................................................................................................................28-31

INFORMATION FÉDÉRALE SUR LES ÉMISSIONS

Viper

garantit à l’acheteur au détail, que ce petit moteur hors route a été conçu, construit et équipé de manière à être conforme, au mo-

ment de la vente initiale, à toutes les réglementations en vigueur de l’agence pour la protection de l’environnement américaine (EPA).

ENREGISTREMENT ET SERVICE

Enregistrer le numéro de modèle et le numéro de série du moteur dans l’espace prévu pour y accéder facilement lors des commandes

de pièces détachées ou demandes d’assistance technique. À l’exception des articles couverts par la garantie sur le contrôle des

émissions, la garantie est valable uniquement si l’enregistrement dûment rempli est reçu par Viper® dans les 30 jours après l’achat.

(POUR PLUS DE RENSEIGNEMENTS, VOIR LA SECTION SUR LA GARANTIE.) La garantie pour votre moteur Viper® est respectée en

enregistrant le produit que le moteur Viper® alimente. L’enregistrement de la garantie peut se faire en ligne à www.ardisam. com ou

par courrier à : Ardisam, 1160 Eighth Avenue, Cumberland, WI 54829. Vous pouvez aussi appeler notre service à la clientèle au (800)

345-6007 du lundi au vendredi de 8h00 à 17h00 HNC.

RENSEIGNEMENTS D’ACHAT

Lieu de l’achat:

Adresse du lieu de l’achat:

Ville : Province: Code Postal:

Numéro de modèle: Numéro de série (trouvé à côté d’autocollant de

sécurité):

Date d’achat :

Note:

Ce manuel comprend de l’information pour plusieurs modèles. Lisez et conservez ce manuel d’instructions pour consultation

future. Ce manuel contient de l’information importante concernant LA SECURITÉ, LE MONTAGE, L’OPÉRATION et L’ENTRETIEN.

Le propriétaire doit être certain que toute information concernant le produit est incluse avec l’appareil. Cette information

comprend le MANUEL, les PIÉCES DE RECHANGE et les GARANTIES. Cette information devrait être fournie pour s’assurer que les

lois de l’état et autre lois sont respectées. Ce manuel devrait rester avec l’appareil même si l’unité est revendue.

Manuel de l’opérateur

Tarière à glace à moteur ESKIMO

Voir les pièces détachées en ligne à www.geteskimo.com ou composer le 800-345-6007 L-V 8h-17h HNC

AVERTISSEMENTS ET MESURES DE SÉCURITÉ

RESPONSABILITÉ DU PROPRIÉTAIRE

La responsabilité du propriétaire est d’assurer un usage précis,

sûr et ecace.

• Lisez et suivez toutes les consignes de sécurité.

• Suivez attentivement toutes les instructions d’assemblage.

• Faites l’entretien de la tarière selon les directives et le pro-

gramme d’entretien inclus dans ce manuel de l’opérateur

Eskimo®.

• S’assurer que toute personne qui utilise cette tarière soit

familier avec les commandes et les mesures de sécurité.

MESSAGES SPÉCIAUX

Votre manuel contient des messages spéciaux pour attirer

votre attention sur des problèmes potentiels de sécurité, sur

des dommages potentiels à l’équipement ainsi que des infor-

mations d’opération et d’entretien utiles. Veuillez lire toutes les

informations attentivement an d’éviter des blessures et des

dommages à l’équipement.

NOTE : De l’information générale qui peut aider l’opérateur

au niveau de l’opération et de l’entretien de l’équipement est

fourni à travers le manuel.

Ce symbole met l’emphase sur des consignes de

sécurité importantes qui, si ignorées, pourraient

mettre en danger votre sécurité personnelle.

AVANT DE METTRE EN MARCHE :

AVERTISSMENT

AVERTISSEMENT INDIQUE UNE SITUATION POTENTIEL

LEMENT DANGEREUSE QUI, SI ELLE N’EST PAS ÉVITÉE,

POURRAIT CAUSER LA MORT OU DE GRAVES BLESS

URES ET/OU DOMMAGES À LA PROPRIÉTÉ

ATTENTION

ATTENTION INDIQUE LE RISQUE DE BLESSURES OU

DE DOMMAGES MATÉRIELS SI LES INSTRUCTIONS DE

SÉCURITÉ QUI SUIVENT CE MOTINDICATEUR NE SONT

PAS RESPECTÉES.

IMPORTANT

IMPORTANT SIGNALE DES INFORMATIONS UTILES

CONCERNANT L’ASSEMBLAGE, L’UTILISATION OU L’EN

TRETIEN DU MATÉRIEL

AVERTISSMENT

LE NON OBSERVATION DES CONSIGNES DE SÉCURITÉ

ET DES INSTRUCTIONS DE FONCTIONNEMENT POUR

RAIT ENTRAINER LA PERTE DE CONTRÔLE DU MOTEUR,

DES BLESSURES PERSONNELLE ET/OU À D’AUTRES PER

SONNES, ET DES RISQUES DE DOMMAGES À LA PRO

PRIÉTÉ.

AVERTISSMENT

LISEZ ENTIÈREMENT DES DIRECTIVES DE

FONCTIONNEMENT ET D’ENTRETIEN POUR CE PRODUIT

ET LES DIRECTIVES POUR L’ÉQUIPEMENT ACTIONNÉ

PAR CE MOTEUR. LE FAIT DE NE PAS RESPECTER

LES INSTRUCTIONS PEUT ENTRAÎNER DE GRAVES

BLESSURES OU LA MORT. OPÉRER LE MOTEUR TEL QUE

DES CONSIGNES DE SÉCURITÉ DÉFINIES ICI ET CEUX

QUI SONT INSÉRÉES DANS LE TEXTE. L’UTILISATEUR

DOIT CONNAÎTRE LE CONTENU DE CE MANUEL, ET ÊTRE

FAMILIARISÉ AVEC LES CONTRÔLES.

AUTOCOLLANTS DE SÉCURITÉ:

Ci-dessous vous trouverez trois autocollants d’avertissement

xés sur la tarière. Il est important de lire toutes les mesures

de sécurité et de localiser les étiquettes d’avertissement avant

d’utiliser ce produit.

WARNING!

Failure to read, understand and

follow all warnings and instruc-

tions listed could result in seri-

ous injury or death. Keep all body

extremities, loose clothing and

foreign objects clear of rotating

auger. Be sure auger is securely

attached to powerhead during

use. Never carry auger between

holes with the engine running.

This auger is not designed to be

utilized as an anchoring device.

Use this auger/powerhead as per

provided instructions only.

LBLAUGER R061909

AVERTISSMENT

AVERTISSEMENT PROPOSITION 65 DE CALIFORNIE

L’ÉCHAPPEMENT DU MOTEUR DE CE PRODUIT CON

TIENT DES SUBSTANCES CHIMIQUES DÉCLARÉES RE

SPONSABLES DE CANCER, MALFORMATIONS CONGÉNI

TALES OU AUTRES ANOMALIES DE LA REPRODUCTION

PAR L’ÉTAT DE CALIFORNIE.

Voir les pièces détachées en ligne à www.geteskimo.com ou composer le 800-345-6007 L-V 8h-17h HNC

Manuel de l’opérateur

Tarière à glace à moteur ESKIMO

PRÉCAUTIONS DE SÉCURITÉ IMPORTANTES:

• Les lames de coupe sont extrêmement tranchantes. Soyez

extrêmement prudent lorsque vous percez un trou ou que vous

remplacez les lames. Remettez le protège lames après chaque

utilisation.

• Ne transportez pas la tête motorisée de la tarière entre chaque trou

avec le moteur en marche.

• La tarière ne devrait pas tourner lorsque le moteur tourne au

ralenti. Si elle tourne lorsque le moteur est au ralenti, contactez un

centre de service autorisé Eskimo pour des instructions.

• Gardez toujours les mains, les pieds, les cheveux et les vêtements

amples loin de toutes pièces mobiles du moteur et de la tarière.

• Ne laissez pas des enfants opérer cette appareil. Ne laissez pas des

adultes opérer cet appareil sans directives adéquates.

• N’opérez aucun appareil motorisé sous l’influence de l’alcool ou de drogues.

• Assurez-vous que les écrous, boulons et vis sont bien serrés.

• Le moteur doit être éteint et refroidi et le câble pour bougie doit

être enlevé de la bougie avant de tenter toutes réparations.

• La température du silencieux et des zones avoisinantes peut

dépasser 65° C (150° F). Évitez ces zones.

• Ne faites jamais fonctionner le moteur à l’intérieur ou dans un

endroit fermé. L’échappement du moteur contient du monoxyde

de carbone, un gaz inodore et mortel.

• Si la tarière à glace ne tourne pas dans un trou, éteignez le moteur

et laissez refroidir avant de tenter de l’enlever manuellement.

MESURES DE SÉCURITÉ POUR LE MOTEUR

Prévenir l’Empoisonnement au Monoxyde de Carbone

• N’essayez jamais de ventiler l’échappement du moteur à l’in-

térieur. Le monoxyde de carbone peut atteindre des niveaux dan-

gereux très rapidement.

• Ne faites jamais fonctionner le moteur à l’extérieur là où les

fumées peuvent être attirées dans un édice.

• Ne faites jamais fonctionner le moteur à l’extérieur dans un en-

droit mal ventilé où les fumées d’échappement peuvent être con-

tenues et non facilement évaporées. (Par exemple : dans un grand

trou ou des endroits qui sont couverte de bancs de neige).

• Ne faites jamais fonctionner le moteur dans un endroit fermé ou

partiellement fermé. (Par exemple : des édices qui sont fermés sur

un ou plusieurs côtés, à l’intérieur des abris, garages ou sous-sols).

• Faites toujours fonctionner le moteur avec l’échappement et le

silencieux dirigés loin de l’opérateur.

AVERTISSMENT

NE PAS ALTÉRER/MODIFIER LE MOTEUR:

N’ALTÉRER OU NE MODIFIER JAMAIS LE MOTEUR FABRIQUÉ

EN USINE. SI LE MOTEUR EST ALTÉRER OU MODIFIER CELA

PEUT CAUSER DE BLESSURES SÉRIEUSES OU LA MORT.

LORS DES RÉPARATIONS OU REMPLACEMENT DE PIÈCES DE

MOTEUR, VOUS DEVEZ TOUJOURS DÉBRANCHER LE CÂBLE

POUR LA BOUGIE ET GARDERLE LOIN DE LA BOUGIE.

PORTEZ TOUJOURS DES PROTECTEURS D’OREILLE LOR

SQUE VOUS FAITES FONCTIONNER LE MOTEUR.

VEUILLEZ NE PAS DÉMARRER VOTRE TARIÈRE À GLACE

JUSQU’À CE QUE VOUS AYEZ LU LA SECTION PRÉCÉDENTE

DE CE MANUEL. SI VOUS LES AVEZ LUS, SUIVEZ LES ÉTAPES

DÉCRITES SUR LES PAGES SUIVANTES POUR DÉMARRER

VOTRE TARIÈRE À GLACE.

N’ENTREPOSER JAMAIS LE MOTEUR AVEC DU CARBURANT

DANS LE RÉSERVOIR À L’INTÉRIEUR. LE CARBURANT ET LES VA

PEURS DE CARBURANT SONT HAUTEMENT INFLAMMABLES.

NE MÉLANGER JAMAIS LE CARBURANT ET L’HUILE DIRECTE

MENT DANS LE RÉSERVOIR DE CARBURANT DU MOTEUR.

UTILISER UNIQUEMENT DES CONTENANTS DE CARBURANT

PORTABLES, NON MÉTALLIQUES APPROUVÉS PAR UNDER

WRITER’S LABORATORY U.L. OU AMERICAN SOCIETY FOR

TESTING & MATERIALS ASTM.

LA MANIPULATION ET LE REMPLISSAGE DU MOTEUR AVEC

LE CARBURANT DOIT TOUJOURS ÊTRE FAIT PAR UN ADULTE.

MANIPULEZ TOUJOURS LE CARBURANT DANS UN ENDROIT

BIEN VENTILÉ, À L’EXTÉRIEUR, LOIN DES FLAMMES ET DES

D’ÉTINCELLES

AVERTISSMENT

TOUS LES MOTEURS ÉMETTENT DU MONOXYDE DE CAR

BONE, UN GAZ INODORE, INCOLORE, MORTEL, INCOLORE,

LE MONOXYDE DE CARBONE PEUT ÊTRE PRÉSENT MÊME SI

VOUS NE POUVEZ PAS LA SENTIR NI VOIR D’ÉCHAPPEMENT

DU MOTEUR. RESPIRER DU MONOXYDE DE CARBONE PEUT

CAUSER DES NAUSÉES, DE LA SOMNOLENCE, ÉTOURDISSE

MENTS, CONFUSION ET ÉVENTUELLEMENT LA MORT.

SI VOUS RESSENTEZ N’IMPORTE QUEL DE CES SYMPTÔMES,

RECHERCHEZ L’AIR FRAIS ET OBTENIR IMMÉDIATEMENT

DES SOINS MÉDICAUX.

DÉMARRER ET FAIRE FONCTIONNER LE MOTEUR À L’EX

TÉRIEUR. NE JAMAIS DÉMARRER OU LAISSER FONCTION

NER LE MOTEUR DANS UN ENDROIT FERMÉ, MÊME SI LES

PORTES ET LES FENÊTRES SONT OUVERTS.

• Ne dirigez jamais le silencieux vers une autre personne. Les per-

sonnes doivent toujours être à une distance de plusieurs pieds du

fonctionnement du moteur et de ses accessoires.

IMPORTANT

L’UTILISATION DU BLOC MOTEUR OU DE LA TARIÈRE POUR

ENTRAÎNER OU AUTREMENT UTILISER TOUT PRODUIT

OU DISPOSITIF FABRIQUÉ PAR UNE ENTITÉ OU PERSONNE

AUTRE QU’ARDISAM, INC. INVALIDERA LA GARANTIE ET

SIGNIFIERA LA RENONCIATION À TOUTE ACTION EN

RESPONSABILITÉ À L’ENCONTRE D’ARDISAM, INC.

La page charge ...

Eskimo F1 ROCKET Manuel utilisateur

Marque: Eskimo

Modèle: F1 ROCKET

Taper: Manuel utilisateur

Ce manuel convient également à

F1R08
F1R10

Télécharger le PDF

rapport

dans d''autres langues

English: Eskimo F1 ROCKET User manual

Eskimo F1 ROCKET Manuel utilisateur

Ce manuel convient également à

Eskimo F1 ROCKET Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents