LG LFX28968ST Le manuel du propriétaire

OWNER’S MANUAL

FRENCH DOOR

REFRIGERATOR

Please read this owner's manual thoroughly before

operating and keep it handy for reference at all times.

LFX28968**

P/No. : MFL63264273

www.lg.com

ENGLISH

FRANÇAIS ESPAÑOL

2

TABLE OF CONTENTS

ENGLISH

TABLE OF CONTENTS

3 PRODUCT FEATURES

4

IMPORTANT SAFETY

INSTRUCTIONS

7 COMPONENTS

7 Refrigerator Exterior

8 Refrigerator Interior

9 INSTALLATION

9 Installation Overview

10 Specifications

11 Unpacking Your Refrigerator

11 Choosing the Proper Location

11 - Flooring

12 - Ambient Temperature

12 - Measuring the Clearances

12 Removing/Assembling the Refrigerator

Door Handles

13 Removing/Assembling the Freezer

Drawer Handle

13 Removing/Assembling the Doors and

Drawers

13 - Removing the Left Refrigerator Door

14 - Removing the Right Refrigerator Door

15 - Assembling the Left Refrigerator Door

16 - Assembling the Right Refrigerator Door

16 - Removing the Freezer Drawers

17 - Assembling the Freezer Drawers

18 Connecting the Water Line

18 - Before You Begin

18 - Water Pressure

18 - What You Will Need

19 - Water Line Installation Instructions

21 Turning On the Power

22 Leveling and Door Alignment

22 - Leveling

22 - Door Alignment

23 HOW TO USE

23 Before Use

24 Control Panel

24 - Control Panel Features

26 In-Door Ice Bin

26 - Detaching the In-Door Ice Bin

26 - Assembling the In-Door Ice Bin

27 Automatic Icemaker

27 - Turning the Automatic Icemaker On or

Off

28 - When You Should Turn the Icemaker Off

28 - Normal Sounds You May Hear

28 - Preparing for Vacation

29 Ice and Water Dispenser

29 - Dispenser

29 - Using the Dispenser

29 - Locking the Dispenser

29 - Cleaning the Dispenser Stand

30 Storing Food

30 - Food Preservation Location

31 - Food Storage Tips

31 - Storing Frozen Food

32 Humidity Controlled Crisper

33

Detaching and Assembling the Storage Bins

34 Adjusting the Refrigerator Shelves

35 MAINTENANCE

35 Cleaning

36 Light bulb replacement

37 General Information

38 Replacing the Water Filter

42 SMART DIAGNOSIS

42 Using Smart Diagnosis

43 TROUBLESHOOTING

53 WARRANTY

3

PRODUCT FEATURES

ENGLISH

PRODUCT FEATURES

* Depending on the model, some of the following functions may not be available.

FILTERED WATER AND ICE DISPENSER

The water dispenser dispenses fresh, chilled water.

The ice dispenser dispenses cubed and crushed ice.

DOOR ALARM

The Door Alarm function is designed to prevent refrigerator malfunctioning

that could occur if a refrigerator door or freezer drawer remains open. If a

refrigerator door or freezer drawer is left open for more than 60 seconds, a

warning alarm sounds in 30 second intervals.

HUMIDITY CONTROLLED CRISPER

The Humidity Controlled Crisper is designed to help keep your fruits and

vegetables fresh and crisp. You can control the amount of humidity in the

crisper by adjusting the setting between Low and High.

GLIDE‘N’SERVE

Glide`N’Serve provides storage space that keeps the compartment colder

than the refrigerator.

It is a convenient place to store sandwiches or meat to be cooked.

ICE PLUS

Ice production can be increased by approximately 20 percent when the

freezer section is maintained at the coldest temperature for a 24-hour

period.

:This product contains chemicals known to the State of California

to cause cancer and birth defects or other reproductive harm.Wash hands after handling.

5

IMPORTANT SAFETY INSTRUCTIONS

ENGLISH

Do not use this product for special purposes (storage of medicine or test materials or for ships,

y

etc).

Unplug the power plug before cleaning or repairing the refrigerator.

y

When you replace the light bulb in the refrigerator, unplug the refrigerator or turn off the power.

y

Do not modify or extend the power cord.

y

Do not use a dryer to dry the interior. Do not light a candle to remove the interior odor.

y

For your safety, this appliance must be properly grounded. Have the wall outlet and the circuit

y

checked by a qualified electrician to make sure the outlet is properly grounded.

Do not use an outlet that can be turned off with a switch. Do not use an extension cord. It is the

y

user’s responsibility to replace a standard 2-prong wall outlet with a standard 3-prong wall outlet.

Do not, under any circumstances, cut or remove the third (ground) prong from the power cord.

y

Do not use an adapter plug and plug the power plug into a multi-outlet extension cord.

y

Disconnect the power cord immediately if you hear a noise, smell a strange odor or detect

y

smoke.

Turn the power off if water or dust penetrates into the refrigerator. Call a service agent.

y

Do not disassemble or modify the refrigerator.

y

Do not put hands, feet, or metal objects below or behind the refrigerator.

y

Do not operate the refrigerator or touch the power cord with wet hands.

y

In refrigerators with automatic icemakers, avoid contact with the moving parts of the ejector

y

mechanism or with the heating element that releases the cubes. Do not place fingers or hands

on the automatic ice-making mechanism while the refrigerator is plugged in.

When dispensing ice from the dispenser, do not use crystal ceramics.

y

Do not touch the cold surfaces in the freezer compartment with wet or damp hands, when your

y

refrigerator is in operation.

Do not put glass containers, glass bottles or soda in the freezer.

y

This appliance is not intended for use by persons (including children) with reduced physical,

y

sensory or mental capabilities, or lack of experience and knowledge, unless they have been given

supervision or instruction concerning the use of the appliance by a person responsible for their

safety.

Do not refreeze frozen food that have thawed completely. It may result in a serious health issue.

y

If you are throwing away your old refrigerator, make sure the CFC coolant is removed for proper

y

disposal by a qualified servicer. If you release CFC coolant, you may be fined or imprisoned in

accordance with the relevant environmental law.

Junked or abandoned refrigerators are dangerous, even if they are sitting for only a few days.

y

When disposing the refrigerator, remove the packing materials from the door or take off the

doors but leave the shelves in place so that children may not easily climb inside.

READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE.

To reduce the risk of fire, electric shock, or personal injury when using your product, basic safety

precautions should be followed, including the following.

6

IMPORTANT SAFETY INSTRUCTIONS

ENGLISH

CAUTION

Installation

The refrigerator must be properly installed in accordance with the Installer Instructions that

y

were taped to the front of the refrigerator.

Be careful when you unpack and install the refrigerator. Immediately dispose of packing

y

materials (plastic) out of reach of children.

Use

Close the door carefully when children are around.

y

Keep fingers out of pinch point areas; clearances between the doors and cabinets are

y

necessarily small. Be careful closing doors when children are in the area.

If you store food properly, beware that it may fall and cause injury.

y

Maintenance

Do not use strong detergents like wax or thinners for cleaning. Clean with a soft fabric.

y

Wipe foreign objects (dust, water, etc) off the prongs of the power plug and contact areas

y

regularly.

READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE.

To reduce the risk of fire, electric shock, or personal injury when using your product, basic safety

precautions should be followed, including the following.

SAVE THESE INSTUCTIONS

7

COMPONENTS

ENGLISH

COMPONENTS

Use this page to become more familiar with the parts and features of your refrigerator.

Page references are included for your convenience.

*The appearance and specifications of the actual product may differ depending on the model.

Refrigerator Exterior

LED Display

Displays the refrigerator and

freezer temperature, the water

filter condition and the dispenser

status.

Ice Plus

When this feature is activated,

the freezer section will run at the

coldest temperature for a 24-hour

period to increase ice production.

Door Alarm

A warning alarm sounds at 30-

second intervals when the

refrigerator or freezer door is left

open for more than 60 seconds.

Filtered Water and

Ice Dispenser

Dispenses fresh, chilled,

filtered water through

the door. The ice

dispenser offers cubed

or crushed ice.

Ez Handle

Easily opens the freezer

door.

8

COMPONENTS

ENGLISH

Refrigerator Interior

Modular Door Bin

Fixed Door Bin

Pullout Drawer

LED Interior Lamps

The interior lamps light up the

inside of the refrigerator.

Refrigerator Shelves

The shelves in your

refrigerator are adjustable

to meet your individual

storage needs.

Durabase Divider

Durabase

Fixed Door Bins

Can Storage Bin

Used to preserve chilled

food or drinks.

Water Filter

Mullion

Folds in when the

left door is opened.

SpacePlus Ice System

Automatically produces

80-130 ice cubes in a

24-hour period.

Crispers

Controls humidity and

helps vegetables and

fruit to stay crisp.

Glide’N’Serve

Allows you to store food items

at a different temperature than

the regular refrigerator area.

Removable Ice Storage Bin

The ice storage bin can be

removed to fill ice buckets,

coolers, or pitchers.

Smart Diagnosis Speaker

Hold your phone to this speaker when

activating Smart Diagnosis. Refer to the

Smart Diagnosis section for more details.

9

INSTALLATION

ENGLISH

INSTALLATION

Installation Overview

Please read the following installation instructions first after purchasing this product or transporting

it to another location.

1 Unpacking your

refrigerator

2 Choosing the proper

location

3 Disassembling/Assembling

4 Connecting the water

supply and water line

5 Leveling and Door

Alignment

10

INSTALLATION

ENGLISH

Speciﬁcations

The appearance and specifications listed in this manual may vary due to constant product

improvements.

Bottom-freezer refrigerator model LFX28968**

Description

French Door Refrigerator

Electrical requirements

115 VAC @ 60 Hz

Min. / Max. Water pressure

20 and120 psi (140 and 830 kPa)

Dimensions 35 3/4” (W) X 35 3/8” (D) X 69 3/4” (H), 47 5/8” (D w/ door open)

908 mm (W) X 899 mm (D) X 1772 (H), 1210 mm (D w/ door open)

Net weight

342 lb. (155 kg)

11

INSTALLATION

ENGLISH

Choosing the Proper Location

Select a place where a water supply can

y

be easily connected for the automatic

icemaker.

Unpacking Your Refrigerator

WARNING

Use two or more people to move and

y

install the refrigerator. Failure to do so

can result in back or other injury.

Your refrigerator is heavy. When moving

y

the refrigerator for cleaning or service,

be sure to protect the floor. Always pull

the refrigerator straight out when moving

it. Do not wiggle or walk the refrigerator

when trying to move it, as floor damage

could occur.

Keep flammable materials and vapors,

y

such as gasoline, away from the

refrigerator. Failure to do so can result in

fire, explosion, or death.

Remove tape and any temporary labels from your

refrigerator before using. Do not remove any

warning-type labels, the model and serial number

label, or the Tech Sheet that is located under the

front of the refrigerator.

To remove any remaining tape or glue, rub the

area briskly with your thumb. Tape or glue residue

can also be easily removed by rubbing a small

amount of liquid dish soap over the adhesive with

your fingers. Wipe with warm water and dry.

Do not use sharp instruments, rubbing alcohol,

flammable fluids, or abrasive cleaners to remove

tape or glue. These products can damage the

surface of your refrigerator.

Refrigerator shelves are installed in the shipping

position. Please reinstall shelves according to

your individual storage needs.

Flooring

To avoid noise and vibration, the unit must be

leveled and installed on a solidly constructed

floor. If required, adjust the leveling legs to

compensate for unevenness of the floor. The

front should be slightly higher than the rear to

aid in door closing. Leveling legs can be turned

easily by tipping the cabinet slightly. Turn the

leveling legs to the left to raise the unit or to

the right to lower it. (See Leveling and door

AlIgnment.)

NOTE

Installing on carpeting, soft tile surfaces,

a platform or weakly supported structure

is not recommended.

The refrigerator should always be plugged

y

into its own individual properly grounded

electrical outlet rated for 115 Volts, 60 Hz,

AC only, and fused at 15 or 20 amperes.

This provides the best performance

and also prevents overloading house

wiring circuits which could cause a fire

hazard from overheated wires. It is

recommended that a separate circuit

serving only this appliance be provided.

WARNING

To reduce the risk of electric shock, do not

install the refrigerator in a wet or damp

area.

NOTE

The water pressure must be between

20 and120 psi (140 and 830 kPa)

on models without a water filter and

between 40 and 120 psi (280 and 830

kPa) on models with a water filter.

12

INSTALLATION

ENGLISH

Ambient Temperature

Install this appliance in an area where the

temperature is between 55°F (13°C) and 110°F

(43°C). If the temperature around the appliance

is too low or high, cooling ability may be

adversely affected.

Measuring the Clearances

Too small of a distance from adjacent items

may result in lowered freezing capability and

increased electricity consumption charges.

Allow at least 24 inches (61 cm) in front of

the refrigerator to open the doors, and at

least 2 inches (5 cm) between the back of the

refrigerator and the wall.

2” (5 cm)

24” (61 cm)

Removing/Assembling the

Refrigerator Door Handles

Removing the Handles

1

Loosen the set screws with a

3

/

32

in.

Allen wrench and remove the handle.

2

Loosen the mounting fasteners that

connect to the refrigerator door and handle

using a

1

/

4

in. Allen wrench, remove the

mounting fasteners.

Assembling the Handles

1

Assemble the mounting fasteners at

both ends of the handle using a

1

/

4

in.

Allen wrench.

2

Place the handle on the door by fitting

the handle footprints over the mounting

fasteners and tightening the set screws

with a

3

/

32

in. Allen wrench.

NOTE

Removing the doors is always

recommended when it is necessary to

move the refrigerator through a narrow

opening. If it is necessary to remove the

handles, follow the directions below.

13

INSTALLATION

ENGLISH

Removing/Assembling the

Freezer Drawer Handle

Removing the Handles

1

Loosen the set screws located on the

lower side of the handle with a

1

/

8

in. Allen

wrench and remove the handle.

2

Loosen the mounting fasteners that

connect to the freezer drawer and handle

using a

1

/

4

in. Allen wrench, and remove

the mounting fasteners.

Assembling the Handles

1

Assemble the mounting fasteners at

both ends of the handle using a

1

/

4

in. Allen

wrench.

2

Place the handle on the door by fitting

the handle footprints over the mounting

fasteners and tightening the set screws

with a

1

/

8

in. Allen wrench.

Removing the Left Refrigerator Door

1

The water supply is connected to the

upper right part of the rear surface of the

refrigerator. Remove the ring in the joint

area. Hold the water supply connection

and gently push the Collet to detach the

water supply line as shown in

and .

NOTE

Detachment of the water supply line is

applicable only when detaching the left

refrigerator door.

WARNING

If your entrance door is too narrow for the

y

refrigerator to pass through, remove the

refrigerator doors and move the refrigerator

sideways through the doorway.

Use two or more people to remove and

y

install the refrigerator doors. Failure to do

so can result in back or other injury.

Disconnect the electrical supply to the

y

refrigerator before installing. Failure to do

so could result in serious injury or death.

Do not put hands, feet or other objects into

y

the air vents or bottom of the refrigerator.

You may be injured or receive an electrical

shock.

Be careful when handling the hinge and

y

stopper. It may result in injury.

Remove food and bins from the doors and

y

drawers before detaching.

Collet

Removing/Assembling the

Doors and Drawers

Removing the doors is always recommended

when it is necessary to move the refrigerator

through a narrow opening.

14

INSTALLATION

ENGLISH

2

Open the left door. Remove the top hinge

cover screw (1). Lift up the cover (2).

3

Remove the cover.

4

Pull out the tube (3).

5

Disconnect all wire harnesses (4).

6

Remove the grounding screw (5).

7

Rotate the hinge lever (6)

counterclockwise. Lift the top hinge (7)

free of the hinge lever latch (8).

8

Lift the door from the middle hinge pin and

remove the door.

9

Place the door, inside facing up, on a non-

scratching surface.

CAUTION

When lifting the hinge free of the latch, be

careful that the door does not fall forward.

CAUTION

When lifting the hinge free of the latch, be

careful that the door does not fall forward.

Removing the Right Refrigerator Door

1

Open the door. Remove the top hinge

cover screw (1). Lift up the cover (2).

2

Remove the cover.

3

Rotate the hinge lever (3) clockwise. Lift

the top hinge (4) free of the hinge lever

latch (5).

4

Lift the door from the middle hinge pin and

remove the door.

5

Place the door, inside facing up, on a non-

scratching surface.

(1)

(2)

(4)

(3)

(6)

(7)

(8)

(5)

(2)

(3)

(4)

(5)

(1)

15

INSTALLATION

ENGLISH

1

Lower the door onto the middle hinge pin.

2

Fit the top hinge (7) over the hinge lever

latch (8) and into place.

3

Rotate the lever (6) clockwise to secure

the hinge.

4

Install the grounding screws (5) and

connect the two wire harnesses (4).

5

Push the water tube (3) located at the top

of the left door into the hole beside the left

hinge on the top of the cabinet until it exits

through the back.

6

Insert the water supply tube (3) into the

connector until you see only one scale

mark. Fully insert the tub cover (15 mm).

7

Hook the tabs on the left side of the hinge

cover (1) under the edge of the top hinge (7)

and position the cover in place.

8

Insert and tighten the cover screw (1).

Assembling the Left Refrigerator

Door

Install the left refrigerator door after the right

door is installed.

(2)

(1)

(3)

(4)

(5)

(6)

(7)

(8)

NOTE

1) Gently press the Collet and insert the

tube until only one line shows on the

tube.

(Correct)

(Incorrect)

2) Pull the tube to make sure that the

tube is tightly fastened and then insert

the clip.

Collet

Tube

Insert Line

Clip

9

Insert the water supply tube at least 5/8 in.

(15 mm) into the connector.

10

Hook the tab on the door switch side

of the cover under the edge of the wire

opening in the cabinet top.

11

Position the cover into place. Insert and

tighten the cover screw.

16

INSTALLATION

ENGLISH

CAUTION

Use two or more people to remove and

y

install the freezer drawer. Failure to do so

can result in back or other injury.

Do not hold the handle when removing

y

or replacing the drawer. The handle may

come off and it could cause personal

injury.

Be careful of sharp hinges on both sides

y

of the drawer.

When you lay the drawer down, be

y

careful not to damage the floor.

Do not sit or stand on the freezer drawer.

y

To prevent accidents, keep children and

y

pets away from the drawer. Do not leave

the drawer open.

Removing the Freezer Drawers

The top, middle and bottom drawers are all

removed in the same way. In the following

figures, the Pullout Drawer located above the

freezer drawer is not shown for clarity.

1

Fully extend the freezer drawer. Lifting up

and out to remove the Dura Base basket

making sure to clear the rail system.

2

Remove one white screw

1

on each side

of the rails.

1

Lower the door onto the middle hinge

pin. Make sure that the plastic sleeve is

inserted into the bottom of the door.

2

Fit the top hinge (4) over the hinge lever

latch (5) and into place.

3

Rotate the lever (3) counterclockwise to

secure the hinge.

4

Hook the tabs on the right side of the

hinge cover (2) under the edge of the top

hinge (4) and position the cover in place.

5

Insert and tighten the cover screw (1).

Install the right-side door first.

Assembling the Right Refrigerator

Door

(1)

(2)

(3)

(4)

(5)

1

17

INSTALLATION

ENGLISH

3

Lower door into final position and tighten the

screws.

4

With the drawer pulled out to full extension,

insert the lower basket in the rail assembly.

2

Hook door supports

1

into rail tabs

2

.

Assembling the Freezer Drawer

1

With both hands, pull out each rail

simultaneously until both rails are fully

extended.

3

Holding both sides of the door pull up to

separate the door from the rails.

4

With both hands, hold each rail and push it in

to allow both rails to slide in simultaneously.

CAUTION

Do not hold the handle when removing

or replacing the drawer. The handle may

come off and it could cause personal

injury.

WARNING

If the Durabase divider is removed, there is

y

enough open space for children or pets to

crawl inside. To prevent accidental child and

pet entrapment or suffocation risk, DO NOT

allow them to touch or go near the freezer

drawer.

DO NOT step or sit down on freezer

y

drawer.

2

1

18

INSTALLATION

ENGLISH

CAUTION

Wear eye protection during installation

to prevent injury.

Connecting the Water Line

Before You Begin

This water line installation is not covered by the

refrigerator warranty. Follow these instructions

carefully to minimize the risk of expensive water

damage.

Water hammer (water banging in the pipes) in

house plumbing can cause damage to refrigerator

parts and can lead to water leakage or flooding.

Call a qualified plumber to correct water hammer

before installing the water supply line to the

refrigerator.

If you use your refrigerator before connecting

the water line, make sure the icemaker power

switch is in the OFF (O) position.

Water Pressure

A cold water supply. The water pressure must

be between 20 and 120 psi (140 and 830 kPa)

on models without a water filter and between

40 and 120 psi (280 and 830 kPa) on models

with a water filter.

If a reverse osmosis water filtration system is

connected to your cold water supply, this water

line installation is not covered by the refrigerator

warranty. Follow the following instructions

carefully to minimize the risk of expensive water

damage.

If a reverse osmosis water filtration system is

connected to your cold water supply, the water

pressure to the reverse osmosis system needs to

be a minimum of 40 to 60 psi ( 280 and 420 kPa ),

less than 2.0~3.0 sec. to fill a cup of 7 oz (200 cc)

capacity.

If the water pressure from the reverse osmosis

system is less than 21 psi (145 kPa) (takes more

than 4.0 sec to fill a cup of 7 oz or 200cc capacity):

Check to see if the sediment filter in

y

the reverse osmosis system is blocked.

Replace the filter if necessary.

Allow the storage tank on the reverse

y

usage.

If the issue concerning water pressure

y

from reverse osmosis remains, call a

licensed, qualified plumber.

All installations must be in accordance

y

with local plumbing code requirements.

What You Will Need

Copper Tubing,

y

¼ in. outer diameter, to

connect the refrigerator to the water

supply. Be sure both ends of the tubing

are cut square.

To determine how

y

much tubing you need:

measure the distance

from the water valve on the back of the

refrigerator to the water supply pipe.

Then, add 8 feet

(2.4 m). Be sure there is sufficient extra

tubing (about 8 feet [2.4 m] coiled into 3

turns of about 10 in. [25 cm] diameter)

to allow the refrigerator to move out

from the wall after installation.

Power drill.

y

½ in. or adjustable

y

wrench.

Flat blade and Phillips

y

head screwdrivers.

Two ¼ in. outer

y

diameter compression

nuts and 2 ferrules (sleeves)

to connect the

copper tubing to the shutoff valve and

the refrigerator water valve.

CAUTION

Do not install the icemaker tubing in

areas where temperatures fall below

freezing.

CAUTION

To prevent burns and product damange,

only connect the refrigerator water line to

a cold water supply.

19

INSTALLATION

ENGLISH

NOTE

A self piercing saddle type water valve

should not be used.

NOTE

The hookup line cannot be white, plastic

tubing. Licensed plumbers must use

only copper tubing NDA tubing #49595

or 49599 or Cross Link Polyethylene

(PEX) tubing.

If your existing copper water line has a

y

flared fitting at the end, you will need

an

adapter

(available at plumbing supply

stores) to connect the water line to the

refrigerator OR you can cut off the flared

fitting with a tube

cutter and then use a

compression fitting.

Shutoff valve to

y

connect to the cold water line.

The shutoff

valve should have a water inlet with a

minimum inside diameter of 5/32 in. at

the point of connection to the COLD

WATER LINE. Saddle-type shutoff valves

are included in many water supply kits.

Before purchasing,

make sure a saddle-

type valve complies

with your local

plumbing codes.

Water Line Installation Instructions

Install the shutoff valve on the nearest

frequently used drinking water line.

1

SHUT OFF THE MAIN WATER SUPPLY

Turn on the nearest faucet to relieve the

pressure on the line.

2

CHOOSE THE VALVE LOCATION

Choose a location for

the valve that is easily

accessible. It is best to

connect into the side of a

vertical water pipe. When

it is necessary to connect

into a horizontal water

pipe, make the connection to the top or

side, rather than at the bottom, to avoid

drawing off any sediment from the water

pipe.

3

DRILL THE HOLE FOR THE VALVE

Drill a ¼ in. hole in

the water pipe using

a sharp bit. Remove

any burrs resulting

from drilling the hole

in the pipe. Be careful

not to allow water

to drain into the drill. Failure to drill a ¼ in.

hole may result in reduced ice production

or smaller cubes.

WARNING

When using any electrical device

(such as a power drill) during

installation, be sure the device is

battery powered, double insulated

or grounded in a manner that will

prevent the hazard of electric shock.

20

INSTALLATION

ENGLISH

NOTE

Be sure there is sufficient extra tubing

(about 8 feet coiled into 3 turns of

about 10 in. diameter) to allow the

refrigerator to move out from the wall

after installation.

4

FASTEN THE SHUTOFF VALVE

Fasten the shutoff valve to the cold water

pipe with the pipe clamp.

Pipe Clamp

Saddle-Type

Shutoff Valve

Vertical Cold

Water Pipe

NOTE

Commonwealth of Massachusetts

Plumbing Codes 248CMR shall be

adhered to. Saddle valves are illegal and

use is not permitted in Massachusetts.

Consult with your licensed plumber.

5

TIGHTEN THE PIPE CLAMP

Tighten the clamp screws until the sealing

washer begins to swell.

NOTE: Do not overtighten clamp or

you may crush the tubing.

6

ROUTE THE TUBING

Route the tubing between the cold water

line and the refrigerator.

Route the tubing through a hole drilled in

the wall or floor (behind the refrigerator or

adjacent base cabinet) as close to the wall

as possible.

Pipe Clamp

Clamp Screw

Washer

Inlet End

7

CONNECT THE TUBING TO THE VALVE

Place the compression nut and ferrule

(sleeve) for copper tubing onto the end of

the tubing and connect it to the shutoff

valve. Make sure the tubing is fully inserted

into the valve. Tighten the compression

nut securely.

8

FLUSH OUT THE TUBING

Turn the main water

supply on and flush out

the tubing until the water

is clear.

Shut the water off at the

water valve after about

one quart of water has

been flushed through the tubing.

9

CONNECT THE TUBING TO THE

REFRIGERATOR

NOTE:

Before making the connection

to the refrigerator, be sure that the

refrigerator power cord is not plugged into

the wall outlet.

a. Remove the plastic flexible cap from

the water valve.

b. Place the compression nut and ferrule

(sleeve) onto the end of the tubing as

shown.

c. Insert the end of the copper tubing into

the connection as far as possible. While

holding the tubing, tighten the fitting.

Tubing Clamp

¼ in. Tubing

¼ in.

Compression

Nut

Refrigerator

Connection

Ferrule

(sleeve)

Saddle-Type

Shutoff Valve

Packing Nut

Outlet Valve

Compression

Nut

Ferrule (sleeve)

La page charge ...

LG LFX28968ST Le manuel du propriétaire

LG LFX28968ST Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents