Blue Clean AR383S Mode d'emploi

Questions, problems, missing parts?

Before returning to your retailer, call our

customer service department at 1-866-235-5112,

8 a.m. - 5:00 p.m., CST, Monday - Friday.

www.arblueclean.com

1800 PSI

Electric Pressure Washer

ASSEMBLY, CARE AND

USE INSTRUCTIONS

Model AR 383 S

READ CAREFULLY

IMPORTANT: RETAIN THESE INSTRUCTIONS

AND ATTACH RECEIPT TO MANUAL FOR FUTURE

REFERENCE

92729-LQ

2

TABLE OF CONTENTS

PRODUCT SPECIFICATIONS

TABLE OF CONTENTS

SPECIFICATIONS

Model

Rated PSI

(lbs/sq. in.)

Max GPM

(Gal/per min) Cold Water Volts Amps

Weight

(lbs.)

AR 383 S 1800 1.3

✔

120 13 26

PRODUCT SPECIFICATIONS

Product Specications ...................................................................................................... 2

Package Contents ............................................................................................................. 3

Hardware Contents ........................................................................................................... 3

Safety Information ............................................................................................................. 4

Assembly Instructions ....................................................................................................... 6

Operating Instructions ....................................................................................................... 9

Care and Maintenance ................................................................................................... 13

Pump Saver ..................................................................................................................... 14

Troubleshooting ............................................................................................................... 15

Limited Warranty ............................................................................................................. 16

Replacement Parts List .................................................................................................. 17

3

PACKAGE CONTENTSPACKAGE CONTENTSPACKAGE CONTENTS

HARDWARE CONTENTS

PART DESCRIPTION QUANTITY

G QC Garden Hose Adapter 1

H High/Low Lance Nozzle 1

I Turbo Lance Nozzle 1

J Spray Gun Trigger Lock 1

K Spray Gun 1

L O-Ring Kit 1

AA Screw 1

PART DESCRIPTION QUANTITY

A Power Washer Unit 1

B High Pressure Hose 1

C Nozzle Cleaning Wire 1

D Spray Gun Holster 1

E Nozzle Tray 1

F Clear Quick Connect with

Filter

1

AA

Screw

Qty. 1

Note: Screw is located in

package with manual

ON/I

OFF/O

1800 PSI

E

I

K

C

F

G

D

H

A

J

B

(Hose reel for

storage only)

L

AA

O-Rings

4

SAFETY INFORMATIONSAFETY INFORMATIONSAFETY INFORMATION

Please read and understand this entire manual before

attempting to assemble, operate, or install the product.

This manual contains information that relates to

PROTECTING PERSONAL SAFETY and PREVENTING

EQUIPMENT PROBLEMS. It is very important to read this

manual carefully and understand it thoroughly before

using the product. The symbols listed below are used to

indicate this information.

DANGER

Potential hazard that will result in serious injury or

loss of life.

WARNING

Hazard that could result in serious injury or loss of

life.

CAUTION

Potential hazard that may result in moderate injury

or damage to equipment.

Note: The word “Note” is used to inform the reader of

something the operator needs to know about the tool.

WARNING

To reduce the risk of injury, the user must read

and understand the instructions before using

this product.

1. Warning – When using this product basic,

precautions should always be followed, including the

following

2. Read all the instructions before using the product

3. Know how to stop the product and bleed pressures

quickly. Be thoroughly familiar with the controls.

4. Keep operating area clear of persons

5. Do not overreach or stand on unstable support. Keep

good footing and balance at all times.

6. Follow the maintenance instructions as specied in

the manual

7. To avoid personal injury and/or damage to property

and to maximize your power washing experience,

carefully follow all of the safety tips, instructions,

warnings and safeguards and become familiar with

all of the controls.

8. This power washer conforms to CSA and other safety

and consumer standards. DO NOT modify or rebuild

any part of your power washer.

9. DO NOT use your power washer when you are under

the inuence of alcohol or drugs. Use this power tool

carefully and only when you are alert.

10. Watch your balance and footing while using your

power washer. Surfaces become slippery when wet

and are extra slippery when using a detergent or

cleaner.

11. NEVER operate the power washer in bare feet,

sandals, or open-toed shoes.

12. When using the power washer near children, make

sure they are closely supervised by an adult to avoid

injury. NEVER let a child use the power washer.

13. Keep ngers, hands, feet and any part of your body

clear of the stream of high pressure water. The

powerful spray can cause blindness or blast holes in

the skin. It can break a window if you are too close

when you pull the trigger on the spray gun.

14. ALWAYS wear eye protection to prevent injury to

eyes when operating the power washer.

15. To avoid mishaps or injury, ALWAYS use the trigger

safety lock when not using the power washer even if

the spraying stops for a moment.

16. The power washer is equipped with a Ground Fault

Circuit Interrupter (GFCI) which greatly reduces the

chance of electric shock while the unit is in use. If

replacement of the plug or cord is needed, use only

identical replacement parts.

17. Point the spray gun in a safe direction when

beginning a power washing session.

18. NEVER spray directly at a person, animal, electrical

device or the unit itself.

19. When rst using the spray gun, hold the spray gun

and lance with two hands when pulling the trigger

(one hand to pull the trigger and the other to

stabilize the gun assembly) until you get used to the

“kickback” from the spray gun.

20. When you press the power switch to turn off the

power washer, water pressure may remain in the

system. To discharge the pressure, point the spray

gun in a safe direction and pull the trigger.

21. NEVER spray ammable liquids.

22. NEVER use the power washer in areas that contain

combustible dust, liquids or vapors.

23. Avoid contact of the pressure hose with sharp

objects and examine the hose regularly. Replace

if damaged. Due to the high pressure involved, it

cannot be repaired if cut or damaged.

24. Only use detergent specically formulated for power

washers and follow instructions on the detergent’s

label.

25. Protect eyes, lungs, and skin from exposure to

detergent. Dish or laundry soap is too thick and will

clog the nozzle of your detergent bottle.

5

SAFETY INFORMATION

Double Insolated Product

SAFETY INFORMATIONSAFETY INFORMATION

KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE.

IMPORTANT: Store the power washer indoors to

prevent the water in the unit from expanding under

freezing conditions. When the water freezes and

expands, your power washer will be damaged and

become inoperable. Or, if storing outdoors, it is

recommended you use pump saver (not included) to

protect pumps.

26. NEVER use hot water with your power washer. It will

overheat and damage the high pressure pump.

27. NEVER leave the power washer unattended while it

is powered “ON”.

28. ALWAYS turn the water supply “ON ” before turning

the power washer power to “ON”. Running the pump

dry will cause damage to the internal components.

29. NEVER use a water supply to your power washer

that exceeds 150 PSI maximum.

30. NEVER disconnect the high pressure hose from the

power washer while the system is pressurized.

31. NEVER permanently engage the trigger mechanisms

on the spray gun.

32. NEVER operate the power washer unless all

components are properly and securely connected.

33. NEVER allow the power washer pump to run for

more than one minute after you have turned off the

water supply. This can cause the motor and pump to

overheat and fail.

34. NEVER use lances or other parts that are not

compatible for this specic AR Blue Clean unit.

35. NEVER use an extension power cord since it defeats

the effectiveness of the GFCI and increases the

chance of electrocuting the operator.

36. NEVER spray any electrical outlet with your power

washer.

37. Inspect the power cord before using. DO NOT use it

if it is damaged.

Servicing of a Double-Insulated Appliance

Ground Fault Circuit Interrupter Protection:

This pressure washer is provided with a ground-fault

circuit-interrupter (GFCI) built into the plugs of the

power-supply cord. This device provides additional

protection from the risk of electric shock. Should

replacement of the plug or cord become necessary,

use only identical replacement parts that include GFCI

protection.

In a double-insulated product, two systems of insulation

are provided instead of grounding. Grounding means

are not provided for a double insulated product, nor

should grounding means be added to the product.

Servicing a double-insulated product requires extreme

care and knowledge of the system, and should only be

done by qualied service personnel.

Replacement parts for a double-insulated product must

be identical to the original parts.

A double-insulated product is marked with the words

“Double Insulation” or “Double Insulated”. Product may

also be marked with symbol shown here.

6

PREPARATION

Before beginning assembly of product, make sure all

parts are present. Compare parts with package contents

list and hardware contents list. If any part is missing or

damaged, DO NOT attempt to assemble the product.

Estimated Assembly Time: 5 minutes

Tools Required for Assembly (not included): Phillips

screwdriver

ASSEMBLY INSTRUCTIONS

PREPARATION

Power Unit Assembly

Slide the spray gun holster (D) onto left side, when

facing the unit, of power washer unit (A).

Note: When placing the gun with the lance attached,

the nozzle will rest in this tray.

1

D

A

Screw x 1

AA

Screw

Qty. 1

2

A

E

AA

Slip tab into slot and screw the nozzle tray (E) on bottom

left, when facing the unit, of power washer unit (A).

Secure with screw (AA).

Note: DO NOT use a power screwdriver. When the screw

is completely tight, give a small nal clockwise twist of

the screwdriver.

DO NOT overtighten.

Hardware Used:

7

ASSEMBLY INSTRUCTIONS

3

A

B

4

B

K

Connect the other end of high pressure hose (B) to

spray gun (K) by inserting the brass metal tip of high

pressure hose into the tting just ahead of trigger

guard. It will lock into spray gun with a “click”. Conrm

hose is locked into spray gun by slightly pulling on them.

The hose is now securely attached to spray gun.

Note: DO NOT press button on underside of gun when

connecting hose to gun.

High Pressure Hose Assembly

Screw high pressure hose (B) clockwise onto bottom

left, when facing the unit, front of power washer unit (A).

Pull back collar and insert o-ring post into water outlet

far enough so collar can thread onto outlet threads until

hand tight. If it takes fewer than six turns you have not

properly tightened the high pressure hose tting. It is

easier to position the power washer in front of you to

ensure that the threads are started correctly. Failure

to properly tighten high pressure hose will result in the

hose slipping or popping off immediately upon turning

unit on. Do not worry about damage if this occurs–just

reinstall and take extra care when screwing on the high

pressure hose tting.

Note: DO NOT use pliers or locking pliers to tighten.

2

1

5

B

K

To release hose (B) from spray gun (K), press button

on underside of gun toward trigger guard. The hose will

slide out from connection.

8

ASSEMBLY INSTRUCTIONS

Unlock

Lock

1

2

6

K

J

Locking Spray Gun (before Lance installation)

To lock the trigger of the spray gun (K), aim the gun

away from you and push the lock button from right to

left. After doing so, squeeze or pull the trigger to make

sure it is locked and will not move. Always leave lock

button in locked position when not in use. This ensures

the gun is in “safe” mode until it is ready for use.

High/Low Nozzle Lance and Turbo Nozzle Lance

Installation

While the spray gun (K) is in the locked position, insert

the high/low nozzle lance (H) or turbo nozzle lance (I )

into the end of the spray gun, by inserting and pushing

together turning clockwise simultaneously. To remove,

push together and turn counterclockwise.

Note: Always push the safety lock button to lock the

trigger when changing lances to ensure that they do not

accidentally eject with force during removal.

Note: When using the turbo lance, make sure the turbo

nozzle is screwed on tight at the end of the lance each

time you use it.

Note: Turbo nozzle is not adjustable.

1

2

7

I

IH

K

8

A

F

Garden Hose Adapter Installation

Remove plastic shipping cover on water inlet, front

right side when facing the unit (A). Install clear quick

connect (F) to water inlet by hand tightening clockwise.

9

ASSEMBLY INSTRUCTIONS

2

1

9

G

Attach a garden hose to QC garden hose adapter (G).

Note: Flush out garden hose before connecting

to QC garden hose adapter.

10

F

G

Push the QC garden hose adapter (G) onto the clear

quick connect (F). It will “click” into place. Do not pull

the blue sleeve back while pushing QC garden hose

adapter (G) onto clear quick connect (F). The water is

now connected to your power washer.

Note: To remove water hose, pull back on blue collar

and it will slide off the clear quick connect. This can be

done at any time. Water will not come out of the garden

hose as the blue/black collar has a water stop check

valve. Water will only ow from the garden hose when it

is connected to the clear quick connect.

You have now completed the assembly and are ready

to begin using your electric power washer. Read and

observe all safety instructions.

ASSEMBLY INSTRUCTIONS

OPERATING INSTRUCTIONS

• Turn on water supply at the faucet to completely

open.

• Make sure the “ON/OFF” switch is in the “OFF”

position. The power switch has international symbols

for ‘on’ and ‘off’: On (|) Off (O).

• Unwind the power cord completely and plug the GFCI

into a grounded 120 volt outlet.

• Release safety push trigger lock up and back into

trigger. While pointing the spray gun in a safe

direction, squeeze the trigger on the spray gun until

there is a steady stream of water, letting the water

and air out of the hose. Push trigger lock back down

to lock back into place.

10

OPERATING INSTRUCTIONS

• Turn the power switch to the “ON” (|) position. The

unit will turn on for 1 - 2 seconds and shut off.

This is a normal function of the auto start feature.

Squeeze the spray gun trigger to begin pressure

washing.

• Begin power washing by squeezing the trigger on

the spray gun all the way into the handle.

• Release the spray gun trigger to stop the power

washer

• Allow the motor to come to a complete stop before

squeezing the trigger again.

• Squeezing rapidly will cause the auto start feature

to miss an on/off cycle that may prevent it from

turning on while squeezing trigger after rapid

squeezing. Use slow deliberate trigger pulls to avoid

such symptoms.

OPERATING INSTRUCTIONS

OFF/0

ON/I

OFF/0

ON/I

2

IN position

High Pressure Setting

Fan Spray Pencil Stream

1

• Always test a small area to avoid chance of

damaging the surface.

Using High/Low Nozzle

• High pressure spray is used for cleaning and low

pressure spray activates the detergent function.

• The adjustable spray nozzle had has two (2)

positions:

– IN position for high pressure spray. Twist the nozzle

counterclockwise until it stops and gap is closed.

– OUT position for low pressure spray for detergent

function. Twist the nozzle clockwise until it stops

and gap is open.

• When using the high pressure setting, twist the

nozzle head clockwise or counterclockwise to achieve

the stream desired.

• When using the low pressure setting twist the nozzle

head clockwise to open the fan blades

all the way.

11

OPERATING INSTRUCTIONSOPERATING INSTRUCTIONS

IMPORTANT: When applying detergent using low

pressure spray, the variable spray head must be set

for the “Pencil Stream”. This is when the metal blades

in front of the nozzle are wide open so the detergent

spray is not constricted.

1

2

OUT position

LOW Pressure Setting

Pencil Stream

• When using the detergent, ll it with a properly

formulated detergent or cleaner with water ratio

according to instructions on the container.

• DO NOT use thick gel-like detergents, as they will clog

the power washer and can cause damage.

• When removing the detergent tank remove lid and

place nger in tank lifting up while pulling tank out.

12

OPERATING INSTRUCTIONSOPERATING INSTRUCTIONSOPERATING INSTRUCTIONS

Operation Tips

• If you hear the motor run intermittently when the trigger

is not being squeezed, that is normal.

The pump is priming itself so it is ready to operate when

the trigger is squeezed. Turn off the power washer if not

being used after ve minutes.

• The o-rings on the bayonet end of the nozzle lance

should be cleaned regularly and lubricated with non-

water soluble grease such as petroleum jelly.

• Keep the nozzle cleaning wire for use in unclogging

the nozzle. If you lose the cleaning wire, a straightened

paper clip also works.

How to Avoid Damaging Surfaces

• Damage to surfaces being cleaned occurs because

the impact force of the water pressure exceeds the

durability of the surface. Bare wood can be penetrated;

paint can be peeled off, etc. You can vary the force of

your power washer by controlling:

1. The angle of the surface being cleaned

2. The distance of the nozzle from the surface being

cleaned

• NEVER use a narrow high pressure stream of water on

soft surfaces susceptible to damage.

• Use the high/low nozzle lance when cleaning windows.

Be sure to adjust the nozzle to low spray and place

the nozzle approximately four to ve feet away from

the window with the nozzle at forty ve degree angle.

Squeeze the trigger and vary the spray pattern and

angle until optimum cleaning efciency is achieved.

1

2

1

Spray

Pressure

Using Power Cord

• Easily remove the power cord from side of unit by

swiveling the bottom blue cord hook to the right or left

until it faces up. The power cord then can be easily slid

off of the side of the power washer unit.

• Swivel blue, cord hook back down when ready to wrap

the cord back into place for storage.

CARE AND MAINTENANCE

13

Detergents

• Use detergents designed for power washers. These

can be purchased online at our website www.

arblueclean.com. Hardware stores or home centers

also have power washer detergents for different

cleaning projects. The cleaning solution should be

the consistency of water in order to prevent clogging

your detergent bottle and nozzle.

• This system applies detergent under low pressure.

The cleaning power of the detergents is enhanced

when applied with low pressure and enough time is

given to break down dirt and grime. The combination

of low pressure and chemical action is very effective

and can be better than scrubbing if applied properly.

ALWAYS spray detergent on a dry surface. DO NOT

pre-soak area. Wetting the surface rst dilutes

the detergent and reduces its cleaning ability. DO

NOT allow detergent to dry on surface. On vertical

surfaces being cleaned, apply detergent to lower

surfaces and work your way up to prevent detergent

from causing streaks in the dirt and grime. Rinse

detergent by pressure washing from bottom up for

same reason.

• If a stain is particularly tough, it may be necessary

to reapply the detergent and use a bristled brush to

scrub the stain. Subsequent power washing after

brushing should successfully complete your cleaning

job.

Cleaning Clear Quick Connect

• The screens inside the clear garden hose adapter

should be cleaned periodically. Rinse it with clean

water, and then place it back in the adapter.

Cleaning Nozzles

• A clogged or partially clogged nozzle can cause

signicant reduction of water pressure coming out

of the nozzle and/or cause the unit to pulsate while

spraying.

• Turn off the unit.

• Turn off the water supply to the unit.

• Relieve any pressure trapped in the hose by

squeezing the trigger 2-3 times, and then lock the

spray gun by pushing the lock button from left to

right.

• Remove the lance from the spray gun

• Using the nozzle tip cleaner provided (or an unfolded

paper clip), insert the wire into the nozzle hole and

move back and forth until debris is dislodged.

• Tap quick connect end of lance on hard surface

several times

• Back ush water through the nozzles using garden

hose and highest pressure available (either standard

water nozzle or use your thumb over the nozzle to

create water pressure for back ush).

14

OPERATING INSTRUCTIONSOPERATING INSTRUCTIONSCARE AND MAINTENANCE

Storage

• When your pressure washing session has been

completed, turn off the power switch located on the

front of the power washer. Unplug the power cord

from the outlet. Turn off the water supply. Pull the

trigger on the spray gun 2-3 times to drain out the

excess water and to release any remaining water

pressure. Disconnect the garden hose adapter from

the water inlet. DO NOT allow the power washer to

run with no water owing through it.

• Remove detergent bottle and clean completely.

Residual chemical will stick to the container and can

cause the detergent injector to clog and not function

properly.

• Remove high pressure hose from spray gun.

• Remove lance from the gun. Place the gun in the holder

on the side. Lances are placed into any of the slots in

the back of the unit. Make sure to discard any remaining

detergent from the bottle. Flush the bottle and nozzle

head with fresh water to prevent clogging.

• Hook the power cord around the L-shaped tabs on the

right side of the machine when facing it.

2

1

F

G

PUMP SAVER

Pump Saver is a product that protects and prolongs

the life of the pump. This will keep the internal parts

of the pump lubricated and protected from freezing

while being stored in ALL climates. It also assists with

protection from internal corrosion. The Blue Clean part #

is: PW64511 (16oz. bottle). Order online at

www.arblueclean.com

Pump Saver Instructions

Follow the previous storage instructions for your power

washer. To prevent staining, protect the surface under

the power washer from any excess uid. Wear eye

protection when using this product.

Turn unit off and disconnect all hoses before adding

pump protector. Unscrew threaded top from bottle to

remove seal and reattach threaded top to bottle.

Remove black cap from bottle.

1) Screw garden hose adapter (G) clockwise onto

threaded top of pump saver bottle.

2) To connect, push garden hose adapter (G) and pump

saver bottle rmly into clear quick connect lter (F),

previously installed to pressure washer inlet.

3)

Turn power on. Turn the power washer off as soon as

the Pump Saver begins to exit the pump outlet.

Note: Instructions on Pump Saver Bottle are generic and

not model specic.

15

TROUBLESHOOTING

PROBLEM CORRECTIVE ACTION

Unit will not turn on. 1. The GFCI module on the end of the power cord must be plugged directly into an outlet.

2. Do not use an extension cord.

3. With the GFCI Connected make sure the power switch is turned on.

Note: When power switch is turned on, the power washer will turn on by itself for 1-2

seconds and shut off. This is normal.

The high pressure

(HP) hose will

not connect/stay

connected to the

spray gun. Is this a

spray gun problem?

1. In most cases, the spray gun is not the problem. The problem is the rubber sleeve

covering the tting at the end of the high pressure hose. It has likely slipped up toward

the metal tip. To x: wiggle, twist and/or pull the rubber sleeve down until the entire tip

is visible plus an 1/8 in. of the metal tting below the tip. Now try to insert the hose tip

into the spray gun. It should “click” into place and will not come out until the hose is

released by pushing in the lever on the underside of the gun. You may cut away the end

of the sleeve with a sharp knife if unable to move the sleeve down. Be careful not to cut

or puncture the hose.

2. Do not push in the release button when connecting the high pressure hose.

The unit is running

but there is no water

ow.

1. Check the water source. Unclog the nozzle on the lance. (See nozzle cleaning

instructions under “Cleaning nozzles”.) Or take off the lance and just spray out of the

spray gun. This will indicate if the problem is with the lance.

2. Reconnect the QC Garden Hose Adapter to the clear quick connect.

Why is water leaking

where the high

pressure hose

connects to the spray

gun?

1. Make sure there is an o-ring at the end of the metal tip of the high pressure hose. If

no o-ring is present, the connection between the hose and spray gun will leak. O-Ring

Kits are available online at www.arblueclean.com or call Customer Service at

1-866-235-5112 to place an order.

I can’t remove the

lance from the spray

gun. What should I

do?

1. All lances and the detergent bottles are attached and removed from the extension

lance in the same manner. Insert the quick-release end of the lance/detergent bottle

into the extension lance. Press the extension lance and lance together (about a 1/8”)

and turn clockwise. The lance will lock in place. Remove the lance by reversing this

procedure. Press the extension lance and lance together and turn counter clockwise.

The lance will slide out.

2. Or, hold the extension lance and lance in an upright position with the nozzle end on

the oor. Push the whole assembly straight down to loosen the connection, and then

follow the removal process again. You may also spray soapy water or a lubricant in the

area where the lance connects to the extension lance.

If you have any questions regarding the product, please call customer service at 1-866-235-5112.

CARE AND MAINTENANCE

16

TROUBLESHOOTING

PROBLEM CORRECTIVE ACTION

The power washer

turns on for 2

seconds, shuts off,

and will not turn

back on. Do I have a

defective unit?

1. It sounds like your power washer is working just ne. When the water is connected,

the accessories are assembled properly, and the power switch is turned on, the power

washer may turn on for 1 - 2 seconds to prime the pump. It automatically shuts off and

waits for the spray gun trigger to be pressed. When the trigger is pressed, water starts

owing through the pump. The water sensor in the pump “senses” the moving water

and automatically turns the power washer on.

2. Turn the power switch to off, hold in the trigger on the spray gun, so that you have a

steady stream of water. While you are holding the trigger open on the spray gun, at the

same time, turn the power switch on.

LIMITED WARRANTYLIMITED WARRANTY

This product is under warranty to the original retail consumer against defects in material and workmanship for a

period of 1 (one) year and is a complete “bumper to bumper” warranty including the spray gun, the high pressure

hose and all accessories from the date of purchase. The warranty is not transferable or assignable. This warranty

covers replacement parts. This limited one year warranty applies only to products used in consumer applications

and is void in rental or any commercial application. Reasonable care must be used in conformity with operation and

maintenance instructions in the owner’s manual and quick start guide. Failure to follow these instructions will void

this warranty. This warranty gives you specic legal rights and you may also have other rights which vary from state

to state.

Warranty Process

Keep your original receipt of purchase in case of warranty claim.

If your power washer develops a problem, contact Customer Service:

• Call our toll-free number at 1-866-235-5112. Customer Service is available Monday - Friday 8:00 a.m. to 5:00

p.m. Central Standard Time (CST). The Customer Service person will work with you to x the problem.

If the power washer needs to be returned for repair, shipping costs to the company must be paid by the customer.

A Return Merchandise Authorization (RMA) Number will be issued for the return. Upon receiving the power

washer, the company will repair or replace the unit. We will send unit back to customer at no charge.

Please note: Power washers sent to the company without an RMA Number will NOT be accepted and shipped

back at the expense of the sender.

REPLACEMENT PARTS LIST

17

Printed in China

For replacement parts, call our customer service department at 1-866-235-5112,

8 a.m. - 5:00 p.m., CST, Monday - Friday or order online at www.arblueclean.com

PART DESCRIPTION PART #

G Clear Quick Connect

Filter

PW3082130

H GFCI Assembly PW4221160

I O-Ring Kit PW909104K

J Gun Holster PW4220040

K Nozzle Tray PW4220050

PART DESCRIPTION PART #

A Detergent Tank (28 oz.) PW4220020

B Hose PW4220740

C Spray Gun PW50968

D High/Low Lance Nozzle PW4220010

E Turbo Lance Nozzle PW50976

F QC Garden Hose

Adapter

PW3082731

I

PW909104K

A

B

C

D

E

F

G

H

K

J

18

Questions, problèmes, pièces manquantes?

Avant de retourner l'appareil chez le marchand,

contactez notre service à la clientèle au

1 866-235-5112, de 8 h à 17 h (HNC) du lundi au

vendredi.

www.arblueclean.com

1800 PSI

LAVEUSE À PRESSION ÉLECTRIQUE

GUIDE

D'ASSEMBLAGE,

D'ENTRETIEN ET

D'UTILISATION

Modèle AR 383 S

LIRE ATTENTIVEMENT

IMPORTANT : CONSERVER CE GUIDE ET

INSÉRER LA FACTURE DANS LE GUIDE POUR

RÉFÉRENCE ULTÉRIEURE.

92729-LQ

19

TABLE DES MATIÈRES

SPÉCIFICATIONS

Modèle PSI

nominale

(k/cm2)

(lb/po2)

Débit

maximum

(Litre/min)

(Gal./min)

Eau froide Volts A Poids

(kg)

(lb)

AR 383 S 5 268

(1 800)

4,92

(1,3)

✔

120 13 11,79

(26)

SPÉCIFICATIONS DU PRODUIT

Spécications du produit ................................................................................................ 19

Contenu de l'emballage .................................................................................................. 20

Matériel inclus ................................................................................................................. 20

Consignes de sécurité .................................................................................................... 21

Instructions d'assemblage ............................................................................................. 23

Mode d’emploi .................................................................................................................26

Entretien et maintenance ............................................................................................... 30

Protecteur de pompe ...................................................................................................... 31

Dépannage ...................................................................................................................... 32

Garantie limitée ............................................................................................................... 33

Liste des pièces de rechange ......................................................................................... 34

20

CONTENU DE L'EMBALLAGECONTENU DE L'EMBALLAGE

MATÉRIEL INCLUS

PIÈCE DESCRIPTION QUANTITÉ

G Adaptateur de tuyau d’arro-

sage rapide

1

H Buse de lance HP et BP 1

I Buse de lance turbo 1

J Verrou de la gâchette de

pistolet pulvérisateur

1

K Pistolet pulvérisateur 1

L Ensemble de joints toriques 1

AA Vis 1

PIÈCE DESCRIPTION QUANTITÉ

A Laveuse à pression 1

B Tuyau à haute pression 1

C Tige de nettoyage de la

buse

1

D Étui à pistolet pulvérisateur 1

E Bac à buse 1

F Raccord rapide transparent

avec ltre

1

AA

Screw

Qty. 1

Remarque : Les vis se trouvent

dans l’emballage du manuel

Vis

Qté 1

ON/I

OFF/O

1800 PSI

E

I

K

C

F

G

D

H

A

J

B

(Hose reel for

storage only)

L

AA

O-Rings

Enrouleur,

pour range-

ment uni-

quement

La page charge ...

Blue Clean AR383S Mode d'emploi

Ce manuel convient également à

Blue Clean AR383S Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents