Hinkley 22 Inch ELI Indoor LED Ceiling Fan Manuel utilisateur

CEILING FAN INSTRUCTION MANUAL

22" ELI

INDOOR LED FAN

LED

SO WE’RE HERE IF YOU HAVE A QUESTION, NEED SOME

HELP OR WANT TO CHAT ABOUT OUR PRODUCTS. SEND

SUGGESTIONS OUR WAY TOO—WE’RE ALWAYS LOOKING TO

MAKE YOUR EXPERIENCE WITH HINKLEY A POSITIVE ONE.

This manual contains complete instructions for the

installation and operation of this fan. It has been

designed to make the installation process as easy as

possible. If you are unfamiliar or uncomfortable with

wiring, please contact a qualiﬁed electrician. If you

need additional assistance or have any questions,

please reach out to us.

For warranty information, visit hinkley.com.

>SERVICE@HINKLEY.COM

>800.HINKLEY

>LET’S SEE THAT HINKLEY STYLE @HINKLEY

#HINKLEYSTYLE

WE WANT YOU TO LOVE YOUR NEW FAN

WARNING:

Read and follow these instructions carefully and be mindful of all warnings shown throughout.

TABLE OF CONTENTS

02

03

04

05

06

08

09

10

12

14

15

16

INSTALLING THE WALL CONTROL

OPERATING

CARE AND CLEANING

TROUBLESHOOTING

ENERGY GUIDE

SPECIFICATIONS

SMART BY BOND

GENERAL INSTALLATION & OPERATING

INSTRUCTIONS

IMPORTANT SAFETY PRECAUTIONS

TOOLS & MATERIALS REQUIRED

UNPACKING YOUR FAN

PREPARATION

INSTALLING THE HANGING BRACKET

HANGING THE FAN

ELECTRICAL CONNECTIONS

INSTALLING THE BLADES

02 | hinkley.com

GENERAL INSTALLATION & OPERATION INSTRUCTIONS

1

2

3

4

5

6

7

8

9

10

To ensure the success of the installation, be sure to read the instructions and review the diagrams thoroughly before beginning.

To avoid possible electric shock, be sure electricity is turned oﬀ at the main power box before wiring. All electrical connections

must be made in accordance with local codes, ordinances and/or the National Electric Code. If you are unfamiliar with the

methods of installing electrical wiring and products, secure the services of a qualiﬁed and licensed electrician as well as

someone who can check the strength of the supportive ceiling members and make the proper installation(s) and connections.

WARNING: To reduce the risk of ﬁre, electric shock, or other personal injury, mount fan only on an outlet box or supporting system

marked acceptable for fan support of 35 lbs (15.9 kg) or less and use mounting screws provided with the outlet box. Most outlet

boxes commonly used for the support of lighting ﬁxtures are not acceptable for fan support and may need to be replaced.

Consult a qualiﬁed electrician if in doubt.

Make sure that your installation site will not allow rotating fan blades to come in contact with any object. Blades should be a t least

7 feet from ﬂoor.

Blades should be attached after motor housing is hung and in place. Fan motor housing should be kept in the carton until ready

to be installed to protect its ﬁnish. If you are installing more than one ceiling fan, make sure that you do not mix fan blade sets, as

each blade is part of a weighted set.

After making electrical connections, spliced conductors should be turned upward and pushed carefully up into outlet box. The

wires should be spread apart with the common conductor and the grounding conductor on one side of the outlet box, and the

"HOT" wires on the other side.

Electrical diagrams are for reference only.

After fan is completely installed, check to make sure that all connections are secure to prevent fan from falling and/or causing

damage or injury.

The fan can be made to work immediately after installation - the bearings are adequately charged with grease so that, under

normal conditions, further lubrication is not necessary for the life of the fan.

Do not operate the reverse switch while the fan blades are in motion. The fan must be turned oﬀ and the blades stopped before

reversing the blades direction.

IMPORTANT SAFETY PRECAUTIONS

TOOLS & MATERIALS REQUIRED

WARNINGS:

•PHILLIPS SCREWDRIVER

• FLAT SCREWDRIVER

•WRENCH OR PLIERS

•WIRE CUTTER

• STEPLADDER

•WIRING SUPPLIES AS REQUIRED BY

ELECTRICAL CODE

• Disconnect power by removing fuse or turning off circuit breaker before installing the fan and/or optional lighting.

• Support directly from building structure.

• To reduce the risk of fire, electric shock or personal injury, mount to outlet box marked "acceptable for fan support" and use mounting

screws provided with the outlet box. Most outlet boxes commonly used for the support of lighting fixtures are not acceptable for fan

support and may need to be replaced. Consult a qualified electrician if in doubt.

• Do not use an incandescent light dimmer. Do not use this fan with any transformer type fan speed control device.

• To reduce the risk of personal injury, do not bend the blade arms when installing them, balancing the blades or cleaning the fan.

Do not insert any object(s) between rotating fan blades.

NOTE:

The important precautions, safeguards and instructions appearing in this manual are not meant to cover all possible conditions

and situations that may occur. It must be understood that common sense, caution and carefulness are factors which cannot be

built into this product. These factors must be supplied by the person(s) installing, caring for and operating the unit.

UNPACK YOUR FAN AND CHECK THE CONTENTS.

• Do not discard the carton. If warranty replacement or repair is ever necessary, the fan should be returned in original packing. Remove

all parts and hardware. Do not lay motor housing on its side, or the decorative housing may shift, be bent or damaged.

•Examine all parts. You should have the following:

UNPACKING YOUR FAN

XX=FAN FINISH

1

2

3

4

5

6

7

8

PACKAGE CONTENT

Hanging Bracket

Ceiling Canopy

Downrod Asm.

Yoke Cover

Fan blade (12")

Receiver Incl. 5 Wire Nuts )

HIRO Wall Control w/2032 Battery,

Cradle A, Wall Plate, Face Plate,

remote control,

2 countersunk head tapping screws

2 mechanical screws and 2 Wire Nuts

Cradle B Wall Plate

，，

switch

(for flat wall use only)

12 Hardware Bag

x

Fan Housing with Motor

Trim Ring

Fan nut cover With clip

9(4)LED Bulbs

10

11

T8, E12, 4.5W)

Safety cable hardware

(wood screw, flat washer, cable clamp)

980014FWH/

CN905022

MH905022FHB

CN905022

EST8-4.5W-27

BL905022Fxx

YC902352Fxx

DR94016Fxx

CA900752Fxx

HINKLEY

NOTE: Design of parts shown above may look slightly different for

your specific model of fan.

1

2

3

4

5

6

12

TO MOTOR N

TO MOTOR L

FOR LIGHT

AC IN L

AC IN N

10

UP

HINKLEY

CR2032

11

UP

KCD1 6A 250V AC

25T85 1E4 PTI 175V

CQC CE UL

7

8

9

Bracket Mounting Hardware

(wood screws, screws, lock washers,

star washers, flat washers, wire nuts),

PREPARATION

Parts identiﬁcation on assembled fan.

Blade

Canopy

Motor Housing

INSTALLING THE HANGING BRACKET

Ceiling Fan

Outlet Box

Hanger

Bracket

Outlet Box

Screw

Flat Washer

Lock Washer

CAUTION: To avoid possible electrical shock, be sure electricity is turned oﬀ at

the main power box before wiring. All wiring must be in accordance with

National and Local Electrical Codes and the ceiling fan must be grounded as

a precaution against possible electric shock.

Fig. 1

1

2

3

4

Locate ceiling joist where fan is to be mounted, being sure location

agrees with the requirements in the minimum clearance section of this

guide. Wood joists must be sound and of adequate size to support 35

pounds (See page 2, items 3 and 4).

If not already present, mount a UL listed outlet box marked "suitable for

fan support" following the instructions provided with the outlet box. The

outlet box must be able to support a minimum of 35 pounds.

Remove canopy from hanger bracket. Remove twist-lock trim ring by

rotaing counter-clockwise. Remove canopy screw that does not have

key slot in canopy. Loosen screw with key slot and remove canopy.

Attach hanging bracket to outlet box using screws provided with the

outlet box.

PREPARATION:

Verify you have all parts before beginning the

installation. Check foam insert closely for missing

parts. Remove motor from packing. To avoid

damage to finish, assemble motor on soft padded

surface or use the original foam inset in motor box.

DO NOT LAY MOTOR HOUSING ON ITS SIDE

AS THIS COULD RESULT IN DAMAGE OF THE

DECORATIVE ENCLOSURE.

HANGING THE FAN

Fig. 1

Downrod

Cross Pin

Hanger

Ball Set Screw

Downrod

Hook-up

(3) Wires

Downrod Pin

Security Set Screws

Mounting Collar

Cotter Pin

Top of Fan Body

1

2

3

4

5

Remove ball from downrod by loosening set screw in the

side of the ball. Slide ball down and remove ball pin;

remove ball. (Fig. 1)

Carefully support fan body (motor) in its styrofoam packing

with the mounting collar (where the wires come out) facing

upward.

Loosen the two security set screws and remove the

downrod pin and cotter pin from the coupling on top of the

motor assembly. (Fig. 2)

Carefully feed the electrical lead wires and safety cable

from the fan through the downrod. Thread downrod into

coupler until holes align. Insert downrod pin through holes

in mounting collar and downrod; clip cotter pin through

small hole in end of downrod pin to hold downrod in place.

Tighten security set screws against downrod using a large

ﬂat blade screwdriver to ensure a tight ﬁt against downrod.

Tighten nuts against mounting collar.

Safety Cable

HANGING THE FAN

07 | hinkley.com

Fig. 4

INSTALLATION OF SAFETY CABLE SUPPORT

Attach the wood screw and the ﬂat washer to the ceiling joist as

shown (do not fully tighten). Slide the cable clamp onto the

safety cable from the fan. Loop the safety cable around the

wood screw that was just attached to ceiling joist. Feed the end

of the cable into the clamp and pull as much cable through as

possible. Firmly tighten screw in the clamp. Cut oﬀ excess cable.

Safety Cable

Wood Ceiling Joist

Safety Cable Clamp

Safety Cable Loop

Wood Screw

And Washer

HANGING THE FAN

Ground Wire

Top of Fan Body

Hanger ball

Hook-up (3) Wires

Yoke Cover

Downrod

Canopy

Set screw

Cross Pin

REMEMBER to turn oﬀ the power before you begin.

To properly install your ceiling fan, follow the steps below.

Slip the yoke cover, trim ring and canopy onto the downrod. (Fig. 3)

Slide the hanger ball onto the downrod, insert the cross pin through

Lift ball/downrod/fan into hanger bracket opening.

NOTE: The tab opposite hanger bracket opening should ﬁt in slot

on ball. (Fig. 4)

6

7

8

NOTE:

6 feet of lead wire is supplied on the fan for use with

longer downrods.

Trim Ring

ELECTRICAL CONNECTIONS

1

2

Motor to Receiver Electrical Connections:

Connect the black wire from the fan to the black wire

marked "TO MOTOR L" on the receiver. Connect the

white wire from the fan to the white wire marked "TO

MOTOR N" on the receiver. Connect the blue wire from

the fan to the blue wire marked "FOR LIGHT" on the

receiver. Secure all the wire connections with the plastic

wire nuts provided.

Receiver to House Supply Wires Electrical Connections:

Connect the black (hot) wire from the ceiling to the black

wire marked "AC in L" from the receiver. Connect the

white(neutral) wire from the ceiling to the white wire

marked "AC in N" from the Receiver. Secure the wire

connections with the plastic wire nuts provided.

REMEMBER -Turn off the power! NOTE - Control must be installed

within 30 feet of fan.

CAUTION: To reduce the risk of electric shock, this fan must be

installed with an isolating wall control/switch.

White (neutral)

Green or bare

copper (ground)

White ("AC IN N")

Outlet box

Black (hot)

Black ("AC IN L")

Receiver

White (neutral)

White ("to motor N")

Ground

(green)

(Connect to

ground wire on

hanger bracket

if no house

ground wire

exists.)

Black ("to motor L")

Blue (for light)

Black (motor)

WARNINGS: Check to see that all connections are tight,

including ground, and that no bare wire is visible at the wire

nuts, except for the ground wire.

INSTALLING THE BLADES

Press blade (2) onto motor shaft making sure pin in shaft seats in

slot in top of blade

Attach clip (3) through hole in motor shaft (4)

Thread decorative cap (1) onto end of motor shaft (Left Hand

Thread)

1

2

3

1

4

3

2

1

INSTALLING THE WALL CONTROL

Fig. 1

REMEMBER to turn off the power before you begin.

NOTE - Secures to any surface or application: flat wall, single gang

box, multi gang box.

1

2

3

4

Option 1. Flat Surface Installation

Select a desired location. Use the wall plate to mark the

location of the mounting holes. Plastic wall anchors or

mounting screws are needed for this application. (Fig. 1)

Seat the cradle B into the wall plate. Secure the wall plate

to the wall using the provided hardware.

Snap the face plate cover onto the wall bracket.

Remote transmitter will be held in place with built in magnets.

Remove the existing wall plate and the old switch from the

wall outlet box.

Seat the cradle A into the wall plate. (Fig. 2)

Connect the black lead wires from the switch in the cradle A

to the black wires in the switch box. Hot input wire to one of

the cradle A switch leads. Power lead to the fan is connected

to the remaining switch lead.

Connect the wall plate / cradle A assembly to the wall outlet

box using the supplied hardware.

Snap the face plate cover onto the wall bracket.

Remote transmitter will be held in place with built in magnets.

1

2

3

4

5

6

Option 2. For single gang box

Transmitter

Face plate

Wall plate Cradle B

Wall

Plastic

anchor

Fig. 2

Outlet box

Transmitter

Face plate

Wall plate

Cradle A

HIRO Control System

11 | hinkley.com

Fig. 3

Remove the existing wall plate and old switch from the wall outlet box. (Fig. 3)

Connect the black lead wires from the switch in the cradle A to the black wires in the switch box. Hot input wire to one of the cradle

switch leads. Power lead to the fan is connected to the remaining switch lead. (Fig. 4)

Attach the cradle A to the wall switch box using the supplied hardware.

Attach the multi-gang faceplate to the switch set in the wall outlet box. Cradle A of Hinkley switch will fit in any standard decora

face plate.

Remote transmitter will be held in place with built in magnets.

1

2

3

4

5

Option 3. Multi Gang Wall Switch Box Installation

Outlet box

Face plate

Switch

Fig. 4

Outlet box

Transmitter

Face plate

Cradle A

HIRO Control System

OPERATION

This ceiling fan is equipped with an

automatically learned type remote control.

There is no frequency switches on the

receiver or transmitter. The fan can start to

use once the pairing process is done.

Remove the panel from the transmitter and

then install one 2032 battery (included). You

need to use a coin to open or close the battery

cover. To prevent damage to transmitter,

remove the battery if not use for long periods

of time (Fig. 1)

Fig. 1

Fig. 2

Signal light

ON

OFF

Pairing Process

NOTE: If installing/pairing more than

one fan in an area, the power must be

disconnected from all fans except the

one fan being paired.

With the fan’s power off, restore power to

the fan. Press and hold “ ” button for about

5 seconds and release. If optional light kit is

installed, the light kit will flash three times

and the motor spin up for 10 seconds on low

speed. The fan has completed the pairing

process with the wall control and is ready

for use.

NOTE: A single fan can be controlled with as

many as 3 wall controls in one room. Every

control will need to repeat the pairing

process based on instructions above and

all controls must be within 30 feet of the fan.

1

2

3

4

5

button:

Press this button and release instantly

to turn on or off the light.

button:

Press and hold to dim or brighten

lights to the desired level and release

button:

Press button for turn on and setting

1-3 fan speed.

button:

Press this button to turn the fan off.

Signal light (Fig. 2)

WARNING: Chemical Burn Hazard.

Keep batteries away from children.

This product contains a lithium button/coin

cell battery. If a new or used lithium button

/coin cell battery is swallowed or enters the

body, it can cause severe internal burns

and can lead to death in as little as 2 hours.

Always completely secure the battery

compartment. If the battery compartment

does not close securely, stop using the

product, remove the batteries, and keep it

away from children. IF you think batteries

might have been swallowed or placed inside

any part of the body, seek immediate medical

attention.

The batteries shall be disposed of properly,

including keeping them away from children;

Even used cells may cause injury.

HIRO Control System

13 | hinkley.com

Fig. 3

Fig. 4

SUMMER MODE

CLOCKWISE DIRECTION)

WINTER MODE

COUNTERCLOCKWISE

DIRECTION)

7

8

Summer Mode and Winter Mode Operation

Summer Mode :

A DOWNWARD airflow creates a cooling effect as shown in Figure 3. This allows you to set your air conditioner on a warmer setting

without affecting your comfort.

Winter Mode:

An UPWARD airflow moves warmer air off the ceiling area as shown in Figure 4. This allows you to set your heating unit on a cooler

setting without affecting your comfort.

Reversing switch to change blade direction is located on the top of motor housing.

CARE AND CLEANING

TROUBLESHOOTING

CAUTION:

Switch oﬀ power supply before carrying out any of these checks.

PROBLEM SOLUTION

Periodically it may be necessary to re-tighten screws to prevent clicking or humming sound during operation. This is especially true in climates

with broad temperature and humidity ranges.

When dusting the blades, you must support the blade to prevent bending - no pressure should be applied to the blades. If you experience any

ﬂaws in the operation of your fan, please check the following points.

FAN WILL

NOT START

FAN SOUNDS

NOISY

1. Check main and branch circuit breakers and/or fuses.

2. Check line wire connections to fan housing wiring. Make sure forward/reverse switch is set to one or the other

position, not stuck in between.

1. Check and make sure that all screws in motor housing are snug (but not over tight).

2. Check that wire connectors in canopy are not rattling against each other

3. Check that all bulb(s) are well held in the sockets.

4. Check that the canopy is ﬁrmly attached to hanging bracket and not vibrating against ceiling.

5. Check to assure set screws on both ends of downrod are tight (motor couple and hanger

ball)

15 | hinkley.com

ftc.gov/energy

• The higher the airflow, the

more air the fan will move

• Airflow Efficiency: 34 Cubic

Feet Per Minute Per Watt

Airflow

3,700

Cubic Feet Per Minute

• Based on 12 cents per kWh and 6.4 hours use per day

• Your cost depends on rates

• Energy Use: 21 Watts

and use

$3$34

Cost Range of Similar Models (19” – 84”)

Estimated

Yearly Energy Cost

$6

All estimates based on typical use, excluding lights

ENERGY GUIDE SPECIFICATIONS

AVERAGE PERFORMANCE AND ENERGY INFORMATION

PERFORMANCE

SPECIFICATIONS

STANDARD

HIGH SPEED LOW SPEED

Airﬂow (CFM)

Energy Use (Watts)

Airﬂow Eﬃciency (CFM/W)

Energy Costs (Yearly)

Amps

RPMs

Airﬂow Shown Is a Weighted Average of High and Low Cubic Feet per Minute Based on Close to Ceiling

832

25.7

23

$7

0.21

1191

551

14.7

37

$4

0.18

751

SMART BY BOND (SOLD SEPARATELY)

How to correct "Fan paired to wrong transmitter" on Smart by

Bond fans supporting multiple transmitters:

a) Open the Bond Home app.

b) Tap on the Fan you want to modify.

c) Tap the settings icon in the upper right corner.

d) Scroll down and tap "Manage Remotes".

e) Delete just the remotes in question; or, use the triple-dot menu

and select "Forget all remotes".

f) Tap "Learn a new remote".

g) Follow on-screen prompts to (re) learn the desired remotes into

the fan.

a) Turn mains power OFF to all fans.

b) Turn mains power ON only for the fan needing code correction.

c) Within 15 seconds of turning on, hold down the Speed 1 button

on any compatible transmitter for 20 seconds.

d) The fan light should blink 5 times and may spin up on low speed

for 10 seconds.

e) Wait 10 seconds.

f) Hold down the Power button on the transmitter you wish to pair.

The fan light should flash three times and the motor spin up for

10 seconds on low speed.

g) If you were using the fan on Wi-Fi, you will need to reconnect to

Wi-Fi.

•Smart Phone Method (recommended)

•Factory Reset Method

a) Turn mains power OFF to the fan.

b) Turn mains power back ON on the fan.

c) Hold down the Power button on the transmitter for 5 seconds,

until the fan light flashes 3 times.

d) Repeat steps a--c above 4 more times.

e) The fan's memory is now totally overwritten, and it has forgotten

all other remotes.

•Brute Force Method

https://bondhome.io/app

HINKLEY SMART FAN OPTIONS:

In addition to the included wall control, you can control your Hinkley

fan through the Bond app.

•To use the app, download it for free from the App Store or Google

Play.

• Open the app to create your account. You can also login with

your Facebook or Google account.

• Next, set up a WiFi connection. You will need the SSID and WiFi

password for the network you want to connect to.

• You will receive a prompt to choose the ﬁnish of your fan and

name your fan device.

• The app will walk you through the main screen and show you

how to change fan speeds, dim the light, set timers or utilize

breeze mode.

NOTE: Maximum of 2 fans can operate on a circuit through the

wall control. Maximum of 12 fans can operate on a circuit through

an on/o switch or breaker when utilizing the app for the fan

control (without the wall control in the circuit).

HINKLEY IS PROUD TO PROVIDE YOU WITH CEILING FAN

PRODUCTS THAT ENHANCE YOUR SPACE WITH COMFORT,

PURPOSE AND STYLE. AS A FAMILY COMPANY, WE ARE

COMMITTED TO DESIGN, PERFORMANCE AND QUALITY,

AND WHAT’S IMPORTANT TO YOU IS PARAMOUNT TO US.

FOR A COMPLETE ASSORTMENT OF OUR PRODUCTS AND

SOURCE BOOKS, VISIT HINKLEY.COM.

GLOBAL HEADQUARTERS

33000 Pin Oak Parkway | Avon Lake, Ohio 44012

T (440) 653 5500 | F (440) 653 5555 | hinkley.com

La page charge ...

Hinkley 22 Inch ELI Indoor LED Ceiling Fan Manuel utilisateur

Hinkley 22 Inch ELI Indoor LED Ceiling Fan Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents