Greenlee Pull Connect Manuel utilisateur

Marque: Greenlee

Modèle: Pull Connect

Taper: Manuel utilisateur

INSTRUCTION MANUAL

Pull Connect

Read and understand all of the instructions and safety

information in this manual before operating or servicing

this tool.

KEEP THIS MANUAL

Record serial number here

_______________________

Español ..............20-37

Français .............38-56

Pull Connect

KEEP THIS MANUAL

Table of Contents

Safety Symbols Key ....................................................... 3

Safety Warnings* ............................................................ 4

Greenlee Contact Information ........................................ 4

Tool Description .............................................................. 5

Specications ................................................................. 5

Button & Feature Identication ....................................... 6

LEDs, Icon & Decal Identication ................................... 7

Table 1: Button Press & LED Guide ................................ 8

Table 2: Icon & LED Guide .............................................. 9

Table 3: General Status LED Guide ................................ 9

Training & Qualications ............................................... 10

Pre-Operation Inspection ............................................. 10

Wireless Communication (Greenlee Link) ..................... 10

Tool Set Up & Operation ............................................... 11

Endpoint Mode ...................................................... 12

Repeater Mode ...................................................... 14

Transportation & Storage ............................................. 15

Charging ....................................................................... 15

Cleaning ....................................................................... 15

Service .......................................................................... 15

Disposal ........................................................................ 15

Table 3: Unit Troubleshooting ....................................... 16

Table 4: LED Troubleshooting ....................................... 17

Regulatory Statements ................................................. 18

Pull Connect

This symbol means always wear safety

glasses with side shields or goggles

when handling or using this equipment to

reduce the risk of eye injury.

This symbol means read the operator’s

manual carefully before using the

equipment. The operator’s manual

contains important information on

the safe and proper operation of the

equipment.

This symbol means do not burn the

battery or expose to high heat to reduce

the risk of re or explosion.

This symbol means do not expose the

battery to water or rain to reduce the risk

of electric shock.

This symbol indicates the risk of tripping.

This symbol indicates the risk of electrical

shock.

This symbol means additional information

can be found here.

This symbol means do not lock foot switch

in ON position to reduce the risk of injury

from uncontrolled machine movement.

max

122°F/50°C

Lorem ipsum

This symbol means the battery

temperature should not exceed printed

temperature to reduce the risk of re or

explosion.

Safety Symbols Key

In this operator’s manual and on the product, safety

symbols and signal words are used to communicate

important safety information. This section is provided

to improve understanding of these signal words and

symbols.

This is the safety alert symbol. It is used

to alert you to potential personal injury

hazards. Obey all safety messages that

follow this symbol to avoid possible injury

or death.

indicates a hazardous situation which, if not avoided,

WILL result in death or serious injury.

indicates a hazardous situation which, if not avoided,

COULD result in death or serious injury.

indicates hazards or unsafe practices which, if not

avoided, MAY result in injury or property damage.

Pull Connect

Safety Warnings

Greenlee Contact Information

If you have any questions or need to purchase parts/

accessories for this Greenlee product: Contact your

local Greenlee distributor or Greenlee’s Customer

Service Center.

Additional copies of this manual are available at

www.greenlee.com

Greenlee Customer Service

USA: 1-800-435-0786 | Canada: 800-435-0786

International: 1-815-397-7070

[email protected]

Shipping address:

Greenlee Factory Service Center

4411 Boeing Dr., Rockford, IL 61109

• Keep handles and grasping surfaces dry, clean

and free from oil and grease. Slippery surfaces do

not allow for safe handling and control of the tool

in unexpected situations increasing the risk of injury

and tool damage.

• Changes or modiﬁcations not expressly approved

by the party responsible for compliance could void

the user’s authority to operate the equipment.

Use the correct tool and accessories for your

application. The correct tool will do the job better

and safer at the rate for which it was designed.

Use of the tool for operations different from those

intended can result in a hazardous situation.

Before operating this tool, read and understand:

• This operator’s manual

• The instructions for any other equipment or

material used with this tool

• Markings on the tool

• Required work site safety procedures

SAVE ALL WARNINGS AND INSTRUCTIONS FOR

FUTURE REFERENCE.

• Do not lock foot switch in ON position. The

operator should always be in control of the tool

to decrease the risk of injury from uncontrolled

movement of the tool.

• Maintain communication between operators.

Loss of communication increases the risk of injury

and damage to the tool and cable.

• Do not use Pull Connect in Endpoint Mode outside

the immediate area of operation. One operator

should be located at each endpoint to monitor the

pull and control the foot switches to reduce the risk

of injury.

• Keep proper footing and balance at all times.

This enables better control of the power tool in

unexpected situations.

• Stay alert, watch what you are doing and use

common sense when operating a puller or feeder.

Do not use this equipment while you are tired or

under the inuence of drugs, alcohol or medication.

A moment of inattention while operating power tools

may result in serious personal injury.

• Do not let familiarity gained from frequent use of

these tools allow you to become complacent and

ignore tool safety principles. A careless action can

cause severe injury within a fraction of a second.

• Use the tool in accordance with these instructions,

taking into account the working conditions and

the work to be performed. Use of the tool for

operations different from those intended could result

in a hazardous situation.

• Do not place Pull Connect on ground. Pull Connect

could be damaged and be a tripping hazard.

• Do not carry or unplug the foot switch or Pull

Connect by the cord. Continued abuse can lead to

damage to the cords. Damaged cords increase the

risk of electric shock.

• Do not use Pull Connect if wet. Moisture near

electronics increases the risk of injury and tool

damage from a short circuit.

Pull Connect

Tool Description

The Greenlee Pull Connect is a pulling accessory that communicates the status of the foot switch on Greenlee pullers

and 6810 feeder. It can operate using two modes, Endpoint and Repeater, that uses Greenlee Intelli-Pull™ technology

to send out and receive signals. Through the foot switch the Pull Connect can control the starting and stopping of the

puller and feeder simultaneously.

Features

• Intelli-Pull™ Technology

• Two Operating Modes: Endpoint and Repeater

• Compact and Rugged Design

• Magnets for Mounting Unit

• Simple and Easy to Read Control Panel

Speciﬁcations

Compatible with 6810 Feeder, UT-10, G10 and G6

Dimensions:................................................................. .... ....9.0 in. x 5.0 in. x 1.6 in. (228.6 mm x 127.0 mm x 41.3 mm)

Weight: .................................................................................................................................................. 1.00 lb (0.45 kg)

Operating Temperature: ....................................................................................................... 5°F to 122°F (-15°C to 50°C)

Storage Temperature (long term): ........................................................................................50°F to 122°F (10°C to 50°C)

Contains FCC ID. ................................................................................................................. 2A3WE-XBPSX; SQGBL653

Contains IC. ........................................................................................................................ 28039-XBPSX; 3147A-BL653

Internal Li-Ion Battery

Nominal Voltage: ........................................................................................................... ......................................... 3.63 V

Charging Temperature ...........................................................................................................32°F to 113°F (0°C to 45°C)

Est. Charging Time .................................................................................................................................................... 5 hrs

Est. Operating Time ................................................................................................................................................... 8 hrs

NOTICE To reduce the risk of electronics damage and reduced performance/product life, keep Pull Connect units

more than 6ft (2m) apart after channel is selected.

Intelli-Pull™ is a trademark of Greenlee Equipment, Inc.

All speciﬁcations are nominal and may change as design improvements occur.

Pull Connect

1. Power Button

2. Mode Select Buttons

3. Radio Channel Buttons

4. Stop Button

5. Charger Icon

6. Charger Input Jack

7. Foot Switch Icon

8. Foot Switch Jack

9. Patch Cord Icon

10. Patch Cord Jack

11. Mounting Magnets

12. Housing

Button & Feature Identiﬁcation

Pull Connect

A. General Status LEDs (GREEN/RED)

B. Power Status LED (GREEN/RED)

C. Stop Signal LEDs (RED)

D. Mode Select LEDs (WHITE)

E. Feeder Icon

F. Feeder Foot Switch LED (GREEN)

LEDs, Icon & Decal Identiﬁcation

G. Repeater Mode Icon

H. Puller Icon

I. Puller Foot Switch LED (GREEN)

J. Radio Channel LEDs (GREEN)

K. Signal Strength Icons

L. Signal Strength LEDs (GREEN)

M. Wireless LED (BLUE)

N. Battery Icon

O. Battery LEDs (GREEN/RED)

P. Product Information Decal

CHARGER: USB 5V 1A

Use provided charger only

Solo use el cargador provisto

Utilisez uniquement le chargeur fourni

Do not use foot switch in repeater mode

No utilice el interruptor de pie en modo repetidor

N'utilisez pas la pédale en mode répéteur

52093562 REV 6

Color: CMYK

Material: Empire E-214WVL per UL Standard

5.48" R 0.15”

2.98"

Energía

Puissance

1.Power 2.Mode

Modo

Mode

Press To Stop

Hold To Resume

(Repeater Mode)

Pulsar para Detener

Mantener Pulsado para Reanudar

Appuyez pour Arrêter

Maintenez pour Reprendre

Serial Number :

Model: RGPC01

Additional Info

Select the same channel for all units.

Seleccione el mismo canal para todas las unidades.

Sélectionnez le même canal pour toutes les unités.

3.Channel

Canal

Presione ambos interruptores de pie para moverse.

Appuyez sur les deux pédales pour le mouvement.

4.Press both foot switches to start.

No lo coloque en el suelo para obtener la mejor señal.

Ne pas placer sur le sol pour le meilleur signal.

For best signal, do not place on ground.

Solid Signal Bars = Connection.

Las barras de señal sólidas significan conexión.

Des barres de signal solides signifient une connexion.

CONTAINS FCC ID: 2A3WE-XBPSX

CONTAINS FCC ID: SQGBL653

CONTAINS IC: 28039-XBPSX

CONTAINS IC: 3147A-BL653

Patents:

pat.Greenlee.com

52093562 REV 6

Greenlee Tools, Inc.

4455 Boeing Drive,

Rockford, Illinois 61109 GREENLEE.COM/US/EN/PULL-CONNECT

= Diecut = Clear Film Window

Pull Connect

TABLE 1: BUTTON & LED GUIDE

ID BUTTON ACTION LEDs BEHAVIOR & COLOR MEANING

Power

Button

Press and Hold 4 sec.

to turn ON

ALL

All LEDs turn ON then OFF

except Power Status, Battery

Level & Operating Mode LEDs

stay ON.

Start Up Sequence

Power Status LED

Solid GREEN

Unit is ON

Flashing RED

See Troubleshooting

Operating Mode LEDs

3 Flashing White

This unit is waiting for the operator to

select a mode.

Press and Hold 2 sec.

to turn OFF ALL

OFF

Unit is OFF

3 Mode

Select

Buttons

Press Mode Select

Button next to Feeder

Icon

Feeder Mode LED

Feeder is Solid White and the

others are OFF

This unit is set to Feeder Mode.

Repeater Mode LED

OFF

Radio Channel LEDs

All are Flashing GREEN

Operator can select a radio channel.

Press Mode Select

Button next to Puller

Icon

Puller Mode LED

Puller LED is Solid White and

the others are OFF

This unit is set to Puller Mode.

Repeater Mode LED

OFF

Radio Channel LEDs

All are Flashing GREEN

Operator can select a radio channel.

Press Mode Select

Button next to

Repeater Icon

Repeater Mode LED

Solid White

This unit is set to Repeater Mode.

Feeder/Puller Mode LEDs

Alternating White

Radio Channel LEDs

All are Flashing GREEN

Operator can select a radio channel.

3 Radio

Channel

Buttons

Press 1, 2, or 3. Must

be the same as other

units in system. Radio Channel LEDs

Selected button LED is Solid

GREEN the others are OFF

The radio is broadcasting on this channel.

Stop

Button

Press to Stop Pull. Stop Signal LEDs

Flashing RED

This unit is broadcasting a STOP signal.

Solid RED

Another unit is broadcasting a STOP signal.

The STOP command can only be cleared

on the original unit.

Press and hold until

ﬂashing Stop Signal

LEDs turn OFF. Stop Signal LEDs

OFF

STOP command is cleared.

Operators

must step off then back on to foot

switch to resume pull.

Press after start up

sequence and before

selecting operating

mode.

Wireless LED

Flashing BLUE

Connection with Greenlee Link app

possible.

Solid BLUE

Connected with Greenlee Link app.

Pull Connect

TABLE 3: ICON & LED GUIDE

LED ID ICON BEHAVIOR & COLOR MEANING

Feeder Endpoint

LED

OFF The feeding endpoint foot switch is NOT depressed.

Solid GREEN The feeding-endpoint foot switch is depressed.

Flashing GREEN A Pull Connect, on the same channel, is issuing a STOP command.

Puller Endpoint LED

OFF The puller endpoint foot switch is NOT depressed.

Solid GREEN The puller endpoint foot switch is depressed.

Flashing GREEN A Pull Connect, on the same channel, is issuing a STOP command.

Signal Strength

LEDs

GREEN LEDs Sweep Back and Forth This Pull Connect is searching for compatible signals on the selected

channel.

1 to 5 LEDs Solid GREEN Shows the connection strength to the other feeder/puller endpoint.

Switching Between Different Number of

GREEN LEDs

This Pull Connect is in Repeater Mode and shows the connection strength

of the indicated Feeder or Puller endpoint.

Wireless LED

Flashing BLUE Connection to Greenlee Link app available.

Solid BLUE Connected to Greenlee Link app.

Battery LEDs

1-3 Segments are Solid GREEN Shows the battery charge level.

Bottom Segment is Rapidly Flashing

GREEN Battery is low, charge this Pull Connect.

One or More Segments are Slowly

Flashing GREEN Pull Connect is charging.

TABLE 2: GENERAL STATUS LED GUIDE

LED ID LED BEHAVIOR & COLOR MEANING

General Status

LEDs

Flashing GREEN The Pull Connect is connected to the other endpoint and ready to operate.

Equipment is not active.

Rotating GREEN Both endpoint foot switches are depressed and equipment is in motion.

Flashing RED A STOP signal is broadcasting from this unit.

All equipment is stopped in system.

Solid RED A STOP signal is active on another unit in the system.

All equipment is stopped in system.

OFF No active connections.

Pull Connect

• Daily before use, inspect the tool and correct

any problems before using. If any problems are

found, do not use this tool until the problems have

been xed. Failure to follow these steps increases

the risk of injury.

• Keep handles and grasping surfaces dry, clean

and free from oil and grease. Slippery handles and

grasping surfaces do not allow for safe handling

and control of the tool in unexpected situations.

Pre-Operation Inspection

1. Clean any oil, grease, or dirt from the body and

buttons. A clean tool aids inspection and helps the

operator observe the lights to see the status of the

tool.

2. Look for wear or damage, such as cracks, gouges,

or chips to housing.

3. Check for the presence and condition of decals.

4. Inspect the patch and foot switch cords for damage

and disentangle before use. Never use the cord for

carrying, pulling or unplugging from equipment.

Keep cord away from heat, oil, sharp edges or

moving parts. Damaged or entangled cords increase

the risk of electric shock.

5. For Endpoint mode: Check that the foot switch is

present and in good condition and does not stick

when depressed on.

6. Inspect any other equipment in the system according

to their instruction manuals.

7. Check work area for adequate lighting, a clear, level,

stable and dry place for all equipment.

Wireless Mode

The blue Wireless LED indicates information related to

wireless connection status. The Pull Connect wireless

technology connects to the Greenlee®Link app using a

smartphone or tablet running iOS or Android operating

systems.

To enable wireless connection to the Greenlee® Link app:

1. Download the appropriate Greenlee® Link app to

your device by going to Greenlee.com/apps, the

Google Play Store or the Apple App Store.

2. Turn ON Pull Connect, wait for start up sequence to

nish and Mode Select LEDs start ashing white. Do

not press any of the Mode Select Buttons.

3. Press the Stop Button. When the blue Wireless LED

starts ashing the unit is able to connect to the app.

(Fig. 1)

4. Go into the Greenlee Link app and follow the

instructions to select the serial number of the Pull

Connect in Wireless Mode to start pairing.

5. Wait for the Wireless LED to become solid blue

signalling the unit is connected. The Greenlee Link

app can be used to view data from the Pull Connect

and initiate rmware updates.

The Pull Connect cannot be used for Connected Pulling

while in Wireless Mode. Turn OFF Pull Connect to

exit Wireless Mode. When next turned ON follow the

instructions for the Connected Pulling Modes shown in

this manual.

Figure 1

Training & Qualiﬁcations

Only workers trained and qualied should use this tool,

especially in a live line environment. It is recommended

at least a second trained and qualied person is present

at appropriate distance to respond if needed. Follow all

training and proper job site safety precautions outlined

by your industry, government and employer.

Pull Connect

The Pull Connect has two modes:

• Endpoint Mode: Turns the Pull Connect into an

endpoint attached to the puller/feeder that controls

the start and stop of the pulling system.

• Repeater Mode: A Pull Connect set in this mode is

placed between Pull Connects in Endpoint Mode to

extend the range or avoid obstructions.

See Endpoint or Repeater Mode sections for set up instructions.

A Connected Pulling system needs a Pull Connect in

Puller Endpoint Mode and a Pull Connect in Feeder

Endpoint Mode to function. Pull Connect signals can only

connect to one opposite endpoint signal per channel

(Fig. 2).

See below for suggested set ups and combinations of

equipment. (Fig. 3)

Tool Set Up & Operation

• Do not lock foot switch in ON position. The

operator should always be in control of the tool

to decrease the risk of injury from uncontrolled

movement of the tool.

• Maintain communication between operators.

Loss of communication increases the risk of injury

and damage to the tool and cable.

• Do not use Pull Connect in Endpoint Mode

outside the immediate area of operation. One

operator should be located at each endpoint to

monitor the pull and control the foot switches.

• Keep proper footing and balance at all

times. This enables better control of the tool in

unexpected situations.

• Stay alert, watch what you are doing and use

common sense when operating a puller or

feeder. Do not use this equipment while you

are tired or under the inuence of drugs, alcohol

or medication. A moment of inattention while

operating power tools may result in serious

personal injury.

• Do not place Pull Connect on ground. Pull

Connect could be damaged and be a tripping

hazard.

• Do not carry or unplug the foot switch or Pull

Connect by the cord. Continued abuse can lead to

damage to the cords. Damaged cords increase the

risk of electric shock.

• Do not use Pull Connect if wet. Moisture near

electronics increases the risk of injury and tool

damage from a short circuit.

Figure 2

The Pull Connect is an accessory that equips select models

of pullers (UT-10, G6 and G10) and the 6810 feeder with

Connected Pulling. The purpose of Connected Pulling

is to quickly and accurately deliver, using radio signals,

start and stop commands to both sides of the pull. With

this feature, the pull will not start unless the feeder and

puller foot switches are pressed. This removes the delay

of sending stop commands over hand radios.

NOTICE While using the Pull Connect, the operator is still

responsible for monitoring the status of the pulling system and

reacting appropriately when equipment is not operating as

expected. These actions include stepping off the foot switch or

pressing the STOP button on the Pull Connect so the situation

can be investigated and corrected.

*Adding more than 2 Pull Connects to the system in Repeater Mode

may cause noticeable delays in the signal.

NOTICE To reduce the risk of electronics damage and

reduced performance/product life, keep Pull Connect units

more than 6ft (2m) apart after channel is selected.

CONNECTED PULLING SYSTEM

Feed Side Endpoint Middle Repeater Pull Side Endpoint

Pull Connect

(Endpoint Mode)

+ Greenlee 6810

Cable Feeder Optional: *Up to 2

Pull Connects

(Repeater Mode)

Pull Connect

(Endpoint Mode) +

UT-10, G6 or G10

Pull Connect

(Endpoint Mode) +

Foot Switch

Figure 3

Pull Connect

The pull can be stopped at any time by lifting a foot off

a foot switch or by pressing the STOP button (Fig. 4) on

any Pull Connect in the system.

The Pull Connect broadcasting the stop signal will have

the STOP Signal and General Status LEDs ashing red.

Other units in the system will only show solid red General

Status LEDs and no Stop Signal LEDs(Fig. 5).

The STOP command can only be disabled from the

unit that is sending the signal. If the STOP command is

coming from the unit set for the puller endpoint then that

is the unit that has to be cleared to resume. To clear the

stop command and resume pulling:

1. Press and hold the STOP button until all the red

LEDs turn OFF and the General Status LEDs return

to green.

2. The puller and feeder operators then release and

depress their foot switches again. The equipment will

not start moving if the foot switch is still depressed

after the STOP signal is disabled.

During operation, all the status lights will slowly ash

green when idle, indicating that the Pull Connect is

receiving and repeating signals. When the equipment is

in motion the green General Status LEDs will circulate.

(Fig. 6)

Figure 4

Figure 5

Pull Connect Sending STOP Signal

Pull Connect Receiving STOP Signal

Standby Running

Figure 6

Endpoint Mode Set Up

This mode is used when the Pull Connect is controlling

the start/stop operation on the ends of the pull through

the foot switch. When both foot switches are pressed,

the puller/feeder will move and when one operator steps

off the foot switch, both will stop.

To set up the Pull Connect for Endpoint Mode:

1. Before turning ON puller/feeder, attach Pull Connect

to the equipment’s frame near the control panel using

the mounting magnets. Make sure all lights and icons

are visible on the Pull Connect and puller/feeder. For

the best performance, do not place Pull Connect on

the ground or in direct sunlight. If a unit has to be in

the sun, avoid laying unit at to reduce the risk of

overheating.

When using the Pull Connect with a 6810 Feeder,

make sure that the pendant momentary and the main

power switches are OFF, the E-Stop button is out, and

the speed control dial is set to the 10 o’clock or 11

o’clock position before setting up the Pull Connect.

See the 6810 Feeder manual for more detail on setting

up and using the feeder. Only use the footswitch /

Pull Connect, the 6810’s speed control dial, and the

E-stop to control the 6810 feeder. Do not use the

pendant switch or the main power switch to control

the 6810 Feeder when using the Pull Connect

NOTICE To reduce the risk of electronics damage and

reduced performance/product life, keep Pull Connect units

more than 6ft (2m) apart after channel is selected.

2. Plug a Greenlee foot switch into the Pull Connect’s

foot switch jack. The jack is labeled with this gure

(Fig.7).

3. Plug the smaller end of the patch cord into the patch

cord jack on the Pull Connect. The jack is labeled

with this gure (Fig.8).

4. Plug the larger end of the patch cord into the feeder/

puller’s foot switch jack. The Pull Connect can be

used alone with a foot switch when hand-feeding

cable. The operator should be in full control of the

start and stop of the equipment at all times.

5. Press and hold the Power Button (Fig.9) for 4

seconds to turn ON Pull Connect. All the LEDs on the

Pull Connect will light up and then turn OFF except

for the Power Status, Battery and Mode Select LEDs.

Figure 7

Figure 9

Figure 8

Pull Connect

Repeater Mode to extend or divert the signal around

the obstruction until the bars turn solid.

10. Set up operate the puller/feeder according to their

instruction manuals.

11. Depress the foot switch on the puller/feeder, the

green Endpoint LED will light up next to the Puller or

Feeder icon.(Fig.13)

Both the Puller and Feeder Endpoint LEDs have to

be lit to start the pull; this indicates both operators

are on their foot switches and ready. Stop the pull

by releasing the foot switch or pressing the STOP

button.

Operators should be in control of the foot switch at all

times and be positioned to remove their foot quickly

to reduce the risk of injury and equipment damage.

During operation, when the Pull Connect is receiving and

repeating signals but the equipment is not in motion,

the General Status LEDs will all ash green. When the

equipment is in motion, the green General Status LEDs

will circulate clockwise.

The Pull Connect broadcasting a STOP signal will have

the STOP button and General Status LEDs ashing red.

Other units in the system will have the General Status

LEDs lit solid red.

See Troubleshooting Tables if Power Status LED is

solid or ashing red. The unit does not begin to listen

or repeat signals until a channel has been selected.

6. When the Mode Select LEDs next to the Mode Select

Buttons start ashing white, select Puller or Feeder

endpoint indicated by the icons (Fig. 10).

The Mode Select LED next to the button pressed will

be solid white, and the others will turn OFF.

7. When the Radio Channel LEDs next to the numbered

Radio Channel Buttons start ashing green, press

the button for the channel that matches the other

units in the system. (Fig.11)

The Radio Channel LED next to the button pressed

will turn solid green, and the LEDs for the unused

radio channels will turn OFF.

NOTICE To reduce the risk of electronics damage and

reduced performance/product life, keep Pull Connect units

more than 6ft (2m) apart after channel is selected.

8. Radio the other side of the pull to verify their unit

is set up and on the same channel. All units in the

system must be on the same channel for the signals

to connect and the endpoint designations must

not be the same. If there is already the same kind

of endpoint signal on the channel, the units will not

connect.

9. After selecting the radio channel, wait for the Signal

Strength LEDs to stop sweeping back and forth. 1

to 5 solid green LEDs means a connection has been

made and indicates the strength of the signal (Fig.12).

If the signal bars continue sweeping, the signal may

be blocked or the pulling equipment is too far apart.

Move any obstructions or add Pull Connects in

Figure 11

Figure 12

Figure 10 Figure 13

Pull Connect

5. When the Radio Channel LEDs next to the numbered

Radio Channel Buttons start ashing green, press the

button for the channel that matches the other units in

the system. (Fig.16)

The Radio Channel LED next to the button pressed

will turn solid green, and the LEDs for the unused radio

channels will turn OFF.

NOTICE To reduce the risk of electronics damage and

reduced performance/product life, keep Pull Connect

units more than 6ft (2m) apart after channel is selected.

6. After selecting the radio channel, wait for the Signal

Strength LEDs to stop sweeping back and forth. 1 to 5

solid green LEDs means a connection has been made

and indicates the strength of the signal (Fig.17).

If the signal bars continue sweeping, the signal may

be blocked or the pulling equipment is still too far

apart. Set up a second Pull Connect in Repeater

Mode.

Once the Repeater unit is connected to the Endpoint

units, the Repeater unit’s Mode LEDs for the

Endpoints will alternate turning ON and OFF and the

Signal Strength LEDs will change to reect the signal

strength from the Endpoint illuminated.

Connected Pulling works best with a line of sight between

each piece of equipment; this will create the strongest

connection. If signals need to pass through walls, place

the Pull Connect near the wall closest to the next Pull

Connect.

When the Pull Connect is receiving and repeating signals

but the equipment is not in motion, the General Status

LEDs will all ash green. When the equipment is in motion,

the General Status LEDs will circulate clockwise green.

The Pull Connect broadcasting a STOP signal will have

the STOP button and general status lights ashing red.

All other units will only have the General Status LEDs lit

solid red.

Repeater Mode is best used when weak signals are

detected on Pull Connects in Endpoint mode or a

connection cannot be made because the endpoints are

too far apart or blocked.

It is recommended, no more than two Pull Connects in

Repeater Mode be added to the system. Adding more

than two Pull Connects between endpoints will start

adding noticeable delay into the system.

1. Before setting up a Pull Connect in Repeater Mode,

check that the puller and feeder side Pull Connects

are active and sending out signals.

2. Identify a clear, dry place, off the ground between

the feeder and puller to place the Pull Connect. The

magnets allow for the Pull Connect to attach to a

metal support, equipment or table. For the best

performance, do not place Pull Connect on the

ground or in direct sunlight. If a unit has to be in the

sun, avoid laying unit at.

NOTICE To reduce the risk of electronics damage and

reduced performance/product life, keep Pull Connect

units more than 6ft (2m) apart after channel is selected.

3. Press and hold the Power Button for 4 seconds (Fig.

14). All the LEDs on the Pull Connect will light up

and then turn Off leaving the Power Status LED solid

green.

See Troubleshooting Tables if Power Status LED is

solid or ashing red. The unit does not begin to listen

or repeat signals until a channel has been selected.

4. When the Mode Select LEDs next to the Mode Select

Buttons start ashing white, select Repeater Mode

endpoint indicated by the icon (Fig. 15).

The Mode Select LED next to the button pressed will

be solid white, and the others will turn OFF.

Repeater Mode Set Up

Figure 14

Figure 15

Figure 16

Figure 17

Pull Connect

Service

• Tool service must be performed only by qualiﬁed

repair personnel. Service or maintenance

performed by unqualied personnel could result in

a risk of injury.

• When servicing a tool, use only identical

replacement parts. Use of unauthorized parts

or failure to follow maintenance instructions may

create a risk of electric shock or injury.

• Do not perform any service or maintenance

other than as described in this manual. Personal

injury or damage to the tool may result.

Cleaning

Make sure that all lights are clean and visible at a distance.

Do not use alcohol or other solvents to clean the device.

Wipe the device with a water damp cloth. Allow to dry

completely before turing ON and using.

• Do not attempt to open the tool. It contains no

user-serviceable parts.

If the lowest segment of the battery icon is ashing

rapidly, the battery is low and needs to be charged. When

charging, each segment will go from ashing to solid as

the battery charge level increases. When the battery

is fully charged, all three segments will be solid green.

(Fig.18)

To charge, plug the power cord into the port marked with

the lightning bolt (Fig.19) then plug into a wall socket

using a USB wall adapter. The Pull Connect can be

operated while charging but the time to full charge will

be extended.

If the product fails to charge or turns off unexpectedly,

refer to Troubleshooting section. Do not attempt to open

the Pull Connect to change the battery.

Charging

Figure 19Figure 18

• Do not expose a battery pack or tool to ﬁre

or excessive temperature. Exposure to re or

temperature above 265°F (130°C) may cause

explosion.

• Do not charge tool if wet or in a wet

environment. Moisture near electronics increases

the risk of a short circuit causing a re.

• Follow all charging instructions and do not

charge the battery pack or tool outside

the temperature range speciﬁed in the

speciﬁcations. Charging improperly or at

temperatures outside the specied range may

damage the battery and increase the risk of re.

• Recharge only with the charger speciﬁed by the

manufacturer. A charger that is suitable for one

type of battery pack may create a risk of re when

used with another battery pack.

max

122°F/50°C

Lorem ipsum

Disposal

This tool contains a lithium-ion battery

and can be recycled. Do not dispose of

this item with regular waste.

Parts of these tools contain valuable materials and can be

recycled. There are companies that specialize in recycling

that may be found locally. Dispose of the components in

compliance with all applicable regulations. Contact your

local waste management authority for more information.

Li-ion

Transportation & Storage

Store the Pull Connect, turned OFF and in the provided

carrying bag. Store in a cool, dry place. If left in the car

on a hot day allow a few minutes for the unit to cool

before turning ON or charging. The unit will not work if it

is overheated. Do not store outdoors where the carrying

bag can get wet, it is not waterproof.

Pull Connect

Table 4: Unit Troubleshooting

Problem Possible Cause Solution

Pull Stopped

One of the operators has

released their foot switch.

That operator depresses foot switch again

while other operator is on their foot switch.

One of Pull Connects or pulling

equipment has lost power.

1. Release foot switch and contact other side.

2. Resolve issue and turn the unit or equipment back ON.

3. Follow instructions to set up Connected Pulling.

4. Wait for the connection.

5. Both operators release then depress the foot switch to continue.

Depleted Battery Charge battery or replace with fully charged unit.

The Pull Connect signal is lost or

blocked.

Clear the obstruction and wait for the connection to reestablish.

Release then depress the foot switch to continue.

1. Move the Pull Connect to another location until signal bars are lit

and stable.

2. Both operators release then depress the foot switch to continue.

1. Add up to two more Pull Connects in Repeater Mode to system.

2. Both operators release then depress the foot switch to continue.

Buttons on Pull Connect will

not react and Blue Wireless

LED is ON.

Pull Connect is in wireless

mode. Turn OFF Pull Connect to exit Wireless Mode.

Weak Signal between Pull

Connect units in Endpoint

Mode.

Pull Connects are too far apart. Add up to two Pull Connects in Repeater Mode into system.

Battery in one or more Pull

Connects is low. Charge battery or replace with fully charged unit.

Signal bars continue

sweeping after 20 seconds

without making a connection.

Signal may be blocked.

1. Move any obstructions or add Pull Connects in Repeater Mode to

divert the signal around the obstruction.

2. Wait for the bars turn solid.

Pulling equipment is too far

apart.

1. Add Pull Connects in Repeater Mode to extend the signal.

2. Wait for the bars turn solid.

Battery Low Charge battery or replace with fully charged unit.

Signal bars are alternating

between two different signal

strengths in Endpoint Mode.

Multiple weak signals are being

detected.

1. Move the Pull Connect and pulling equipment closer together or

add up to two Pull Connects in Repeater Mode between endpoints.

2. Adjust position until the Signal Strength LEDs are solid.

Unit will not turn ON

Unit is overheated. 1. Move Pull Connect to shade and allow to cool.

2. After 5 minutes try to turn unit ON again.

Internal Issue Send in for service.

Depleted Battery Charge battery or replace with fully charged unit.

Pull Connect

Table 5: LED Troubleshooting

Problem Cause Solution

3sec

Power Status LED ﬂashes RED twice every 3 seconds.

Unit temperature almost

outside (within 5 °C) operating

temperature.

Move unit somewhere cooler/warmer and wait

for LED to turn Green again. Do not place in

direct sunlight or in a place with excessive heat/

cold.

Press Power

Button to turn ON

unit.

Power Status LED ﬂashes RED

twice then unit turns OFF.

Unit is too hot.

Battery outside of operating

temperature (-15 °C to 50 °C)

Move unit somewhere out of the heat and allow

to cool. Wait for unit to cool down before at-

tempting to turn ON again. Avoid placing unit in

direct sunlight.

Unit is too cold.

Battery outside of operating

temperature (-15 °C to 50 °C)

Move unit to temperature controlled location.

Wait for unit to warm up before attempting to

turn ON again. Do not use in freezing tempera-

tures.

Pull Connect will

not charge when

plugged in. +

Power Status LED flashes RED and all

three Battery Level LEDs flash GREEN

every second.

Unit is too hot/cold.

Battery temperature outside of

battery charging temperature (0 °C

to 45 °C)

Unplug from charger and move unit to a tem-

perature controlled environment. Do not charge

in direct sunlight or in a places with excessive

heat/cold.

Pull Connect

stops working

during operation.

Turn unit OFF then ON to reset.

If after reset the unit still doesn’t work and LEDs are still ﬂashing, send in for service.

Pull Stopped or

Will Not Start after

pressing foot

switch.

STOP button on this Pull Connect is

pressed.

1. Determine the reason for the STOP signal and

resolve issue.

2. Press and hold the STOP button until Stop

Signal LEDs turn OFF and General Status LEDs

return to ﬂashing GREEN.

3. Both operators release then depress the foot

switch to continue.

Both Stop Signal and General Status

LEDs are ﬂashing RED.

STOP button on another Pull

Connect is pressed.

1. Determine the reason for the STOP signal and

resolve issue.

2. Locate the Pull Connect with ﬂashing RED

LEDs to clear STOP signal.

3. Both operators release then depress the foot

switch to continue.

Loss of power on another Pull

Connect in the system.

1. Replace Pull Connect with new unit.

2. Turn all Pull Connects OFF then ON again to

reset.

3. Set up Connected Pulling for all units.

4. Both operators release then depress the foot

switch to continue. .

General Status LEDs are solid RED.

The other endpoint operator is not

depressing their foot switch.

Wait for other LED to turn ON to complete signal

to start Puller and Feeder moving.

If a signiﬁcant time passes without the other

Endpoint being lit, release foot switch and

use hand radio to contact other end for status

update. Both operators must release and depress

their foot switches when ready to continue.

Feeder Endpoint

LED ON

Puller Endpoint

LED OFF

Feeder Endpoint

LED OFF

Puller Endpoint

LED ON

Pull Connect

Regulatory Statements

Model: RGCP01

Responsible Party: Greenlee Equipment, Inc.

4455 Boeing Dr.

Rockford, IL 61109

USA

Patents: pat.Greenlee.com

USA

CONTAINS FCC ID: 2A3WE-XBPSX & SQGBL653

This equipment has been tested and found to comply

with the limits for a Class A digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful

interference when the equipment is operated in a

commercial environment. This equipment generates,

uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instruction

manual, may cause harmful interference to radio

communications.

Operation of this equipment in a residential area is likely

to cause harmful interference in which case the user

will be required to correct the interference at his own

expense.

Changes or modications not expressly approved by

the party responsible for compliance could void the

user’s authority to operate the equipment.

Canada

CONTAINS IC: 28039-XBPSX & 3147A-BL653

This device complies with part 15 of the FCC Rules

and Innovation, Science and Economic Development

Canada’s licence-exempt RSS(s). Operation is subject to

the following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received,

including interference that may cause undesired

operation

L’émetteur/récepteur exempt de licence contenu dans

le présent appareil est conforme aux CNR d’Innovation,

Sciences et Développement économique Canada

applicables aux appareils radio exempts de licence.

L’exploitation est autorisée aux deux conditions

suivantes :

1. L’appareil ne doit pas produire de brouillage;

2. L’appareil doit accepter tout brouillage radioélectrique

subi, même si le brouillage est susceptible d’en

compromettre le fonctionnement.

Pull Connect

MANUAL DE INSTRUCCIONES

Pull Connect

Lea y comprenda todas las instrucciones y la información

de seguridad en este manual antes de hacer funcionar

esta herramienta o realizar tareas de mantenimiento.

CONSERVE ESTE MANUAL

Registre el número

de serie aquí

_______________________

English................1-19

Français .............38-56

La page charge ...

Greenlee Pull Connect Manuel utilisateur

Marque: Greenlee

Modèle: Pull Connect

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Greenlee Pull Connect User manual
español: Greenlee Pull Connect Manual de usuario

Greenlee Pull Connect Manuel utilisateur

Greenlee Pull Connect Manuel utilisateur

dans d''autres langues

Documents connexes