Marson MT8250 Mode d'emploi

Marque
Marson
Modèle
MT8250
Catégorie
Lecteurs de codes à barres
Taper
Mode d'emploi
2D Handheld
Barcode Scanner
2D Handheld Barcode Scanner Quick Guide (Rev5)
P/N: 8013-0070040
SPECIFICATIONS
DIMENSIONS SCANNING RANGE BEEPER INDICATION GENERAL SETTINGS
Light source visible white LED, visible red LED
Sensor 1280 x 800
Scan rate 120 frames/sec
Resolution 3mil/ 0.075mm
PCS 20%
5 Mil Code39: 30 - 150mm
Depth of Field 3 Mil Code39: 60 - 90mm
(Typical)
13 Mil UPC/EAN: 40 - 280mm
10 Mil DataMatrix: 35 - 135mm
15 Mil QR Code: 35 - 205mm
6.67 Mil PDF417: 45 - 140mm
Dimension L166 x W71 x H84 mm
Weight 172g
Connector USB Type A
Cable 210cm/82.67in (Fixed)
Interface USB HID, USB VCP
Indicator LED, Buzzer
Voltage 5VDC±5%
Working Current Typ. 300mA
Standby Current Typ. 65mA
Operating Temp. -20 to 50°C (-4°F to 122°F)
Storage Temp. -40 to 60°C (-40°
F to 140°F)
Ambient Light 70,000 lux (Sunlight)
Drop Durability 1.5M
Symbologies QR Code, PDF417, MicroPDF417, Aztec,
DataMatrix and major 1D barcodes
Quick Guide
FCC WARNING STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
CANADIAN DOC STATEMENT
This digital apparatus does not exceed the Class B limits for radio noise for digital
apparatus set out in the Radio Interference Regulations of the Canadian Department of
Communications.
Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les
limites applicables aux appareils numériques de las classe B prescrites dans le
Réglement sur le brouillage radioélectrique édicté par les ministère des Communica-
tions du Canada.
CE MARKING AND EUROPEAN UNION COMPLIANCE
Testing for compliance to CE requirements was performed by an independent
laboratory. The unit under test was found compliant with all the applicable Directives,
2004/108/EC and 2006/95/EC.
WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT
The WEEE directive places an obligation on all EU-based manufacturers and
importers to take-back electronic products at the end of their useful life.
ROHS STATEMENT OF COMPLIANCE
This product is compliant to Directive 2002/95/EC.
NON-MODIFICATION STATEMENT
Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment
RoHS
1. Take any metals into contact with the terminals in connectors.
2. Use the scanner where any inflammable gases.
If following condition occur, immediately power off the host computer,
disconnect the interface cable, and contact your nearest dealer.
1. Smoke, abnormal odors or noises come from the scanner.
2. Drop the scanner so as to affect the operation or damage its housing.
Do Not
Do not do behavior below.
1. Put the scanner in places excessively high temperatures such as expose
under direct sunlight.
2. Use the scanner in extremely humid area or drastic temperature
changes.
3. Place the scanner in oily smoke or steam environment such as cooking
range.
4. Be covered or wrapped up the scanner in bad-ventilated area such as
under cloth or blanket.
5. Insert or drop foreign materials or water into scanning window or vents.
6. Using the scanner while hand is wet or damp.
7. Use the scanner with anti-slip gloves containing plasticizer and
chemicals or organic solvents such as benzene, thinner, insecticide etc
to clean the housing. Otherwise, it could not result fire and electrical
shock but housing may be broken and injured.
8. Scratch or modify the scanner and bend, twist, pull or heat its interface
cable.
9. Put heavy objects on interface cable.
Do not stare the light source from the scanning window or do not point the
scanning window at other people’s eyes or eyesight may be damaged
by direct exposure under the light.
Do not put the scanner on an unstable or inclined plane.
The scanner may drop, creating injuries.
Once the interface cable is damaged such as exposed or broken copper
wires, stop using immediately and contact your dealer. Otherwise, it could
result fire or electrical shock.
WARNING AND CAUTION
1. The scanner works like an USB keyboard. Make sure
your host device supports USB keyboard before use.
2. Plug the scanner to the USB port of your host device.
The scanner will emit three beeps at power-up.
3. The OS will automatically intall USB driver for the
scanner if it is connected to your host device for the
first time. Wait until the installation finishes.
4. Open Notepad or any application that can accept
keyboard input. Try scanning some random barcodes
and the barcode data will be displayed.
LED INDICATION
GETTING STARTED
(Top View)
5 Mil Code39: 30 - 120mm
3 Mil Code39: 60 - 90mm
13 Mil EAN/UPC: 40 - 280mm
15 Mil QR Code: 35 - 205mm
6.67 Mil PDF417: 45 - 140mm
10Mil Data Matrix: 35 - 135mm
40
°
Unit: MM
Front View Back View
Side View
92mm
165mm
65mm 65mm
measu
•
R
eo
• In
c
r
•
Con
e
• Co
n
C
AN
A
T
his d
i
appa
r
Comm
Le
p
r
é
rr
limite
s
R
églem
RR
ti
o
n
s
d
CE M
A
T
e
s
tin
g
labo
a
20
0
4/
W
A
S
T
T
he
W
impo
t
Single Long Beep Power up
Single Short Beep Good read
Two beeps Successful setup
Off Standby or No power
Blue Power up or Good read
CHECK VERSION
DEFAULT
. A001$
RESET / ABORT
READING MODE
MAGNETIC SWITCH
ENABLE SYMBOLOGIES KEYBOARD LAYOUT
ON
. F034$ . F035$
OFF
TERMINATOR
CR+LF
DISABLE SYMBOLOGIES
DISABLE ALL CODE
. A003$
CAPSLOCK
CAPSLOCK OFF
. A005$ . A004$
CAPSLOCK ON
INVERSE BARCODE
. D022$
ENABLE INVERSE
BARCODE
. D021$
DISABLE INVERSE
BARCODE
VIBRATOR
. D034$
ON
. D035$
OFF
* The LED will turn on when the trigger
is pressed.
* The LED will turn off when trigger is
released.
. F007$
TRIGGER MODE
* By default, the scanner will simply operate
like Trigger Mode which requires manual
trigger. To enable auto-sensing, place the
scanner on an Auto Hands-free Stand or
disable Magnetic Switch by scanning
below configuration barcodes.
BEEP TONE
. F019$
BEEP HIGH
. F018$
BEEP MEDIUM
. F022$
BEEP LOW
. F012$
BEEP OFF
UTF-8 TO UNICODE
. C045$ . C044$
ON
OFF
*.C045$* *.C044$*
AUTO SENSING MODE
. G036$
ENABLE ALL 1D CODE
*.G036$*
. G038$
ENABLE ALL 2D CODE
*.G038$*
. G035$
DISABLE ALL 1D CODE
*.G035$*
. G037$
DISABLE ALL 2D CODE
*.G037$*
*.A005$* *.A004$*
. A006$
CAPSLOCK FREE
*.A006$*
INTERFACE
. C008$ . C006$
USB VCPUSB HID
*.C008$* *.C006$*
OPOS
. A030$ . A031$
ENABLE OPOS
*.A030$* *.A031$*
DISABLE OPOS
  • Page 1 1
  • Page 2 2

Marson MT8250 Mode d'emploi

Marque
Marson
Modèle
MT8250
Catégorie
Lecteurs de codes à barres
Taper
Mode d'emploi
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents