brondell MBH-10 Hand-Held Bidet Holster Integrated Shut Off Le manuel du propriétaire

Owner's Manual

Hand-Held Bidet Holster

with Integrated Shut O

BIDET SPRAYER ACCESSORY

MODELS MBH10/MBH37/MBH40

2

Table of Contents

MBH10/MBH37/MBH40 OWNER'S MANUAL

This manual contains important safety information.

Before operating your Hand-Held Bidet Holster with

Integrated Shut O, please read this manual thoroughly

and retain it for future reference.

01

02

03

PRODUCT INFORMATION

Product Features

Product Dimensions

Product Parts

04

05

PRODUCT INSTALLATION

Before Installation

Installation

07

PRODUCT OPERATION

Using the Hand-Held Bidet Holster

with Integrated Shut O

08 MAINTENANCE

09 PRODUCT SPECIFICATIONS

10 WARRANTY

11 CONTACT

01 ENGLISH

12 SPANISH

24 FRENCH

GENERAL INFORMATION

PRODUCT INSTALLATION

PRODUCT OPERATION

TRANSLATIONS

TECHNICAL INFORMATION

1

Polished Stainless Steel Hand-Held Bidet

Sprayer Mount

Integrated Chrome Water Shut O Handle

Universal Hand-Held Sprayer Holster Works

With Any Sprayer

High-Quality Metal ⅞" T-Valve

Durable Braided Metal Cold Water Hose

No Electricity Or Batteries Required

Easy Installation And Adjustable Toilet Fit

One-Year Warranty

Product Features

PRODUCT INFORMATION

2

Product Dimensions

PRODUCT INFORMATION

2.24 in 1.97 in

15.75 in

11.81 in

3.15 in

0.08 in thick

0.45 in

3

Product Parts

PRODUCT INFORMATION

1. Stainless Steel Mount

2. Cold Water Braided Metal Hose

1. Sprayer Head

2. Metal Sprayer Hose (½" X ½")

3. Large Rubber Washer (1)

4. Cold Water T-Valve Connector

(⅞" x ⅞" x ⅜")

1

2

3

4

MBH-37/MBH-40 Only

4

You must have a CleanSpa hand-held bidet or

equivalent product with a ½" connection sprayer hose

in order to install the Hand-Held Bidet Holster with

Integrated Shut O.

IMPORTANT

Please be advised that the provided cold water T-valve

should be installed at the ﬁll valve under the toilet tank,

NOT at the cold water supply coming from the wall.

Check Water Supply Line

If the pipe that connects the toilet tank ﬁll valve to the

water shuto valve at the wall is rigid, you will need

to purchase a ﬂexible water supply hose to replace

it before installing the Hand-Held Bidet Holster with

Integrated Shut O. The length of the hose may vary

and the top connection size should be ⅞" ballcock to

connect to the T-valve that you will install under the

toilet tank and the bottom connection will vary (most

common are ⅜" and ½” female compression).

Before Installation

PRODUCT INSTALLATION

INCORRECT

Cold Water Supply

Fill Valve

CORRECT

5

Installation

PRODUCT INSTALLATION

Please read these instructions carefully before installing

your Hand-Held Bidet Holster with Integrated Shut

O. Failure to do so could result in ﬂooding, leaking or

damage to the product.

1. Existing Toilet Seat Removal

a. Lift hinge covers and use ﬂathead or Phillips

head screwdriver to remove the mounting bolts.

Alternatively, you may need to loosen mounting

bolts underneath the seat.

b. Remove the toilet seat and set the seat, mounting

bolts and hardware aside.

2. Turn O Water Supply Valve and Flush Toilet

a. Turn water supply valve o to stop the ﬂow of water.

b. Flush toilet and hold down handle to completely

empty tank.

c. Disconnect water supply hose from toilet tank.

Do not disconnect from the water supply valve.

d. If you have a hand-held bidet sprayer already

connected to your toilet tank, remove the existing

T-valve and hand-held bidet sprayer connection

hose.

3. Connect Cold Water T-Valve to the Toilet Tank Fill Valve

a. Install the included ⅞" cold water T-valve with the

large rubber washer provided to the incoming water

connection on the bottom of your toilet tank.

b. Connect the cold water supply line coming from the

wall to the bottom of the T-valve.

4. Connect Cold Water Hose to T-Valve

Connect one end of the Cold Water Braided Metal

Hose to the remaining open side of the installed

T-valve.

Step 3a

Step 3b

Step 1b

Step 2c

Step 4

6

Installation

PRODUCT INSTALLATION

Installing the Hand-Held Bidet Holster

1. Install Hand-Held Bidet Holster on Toilet

a. Place Hand-Held Bidet Holster on the toilet so the

mounting slots line up with the holes in the toilet

ﬁxture.

b. Replace the toilet seat on top of Hand-Held Bidet

Holster and secure using original toilet seat

hardware. Make sure to tighten so that the holster

and seat do not move.

2. Connect Cold Water Hose to Hand-Held Bidet Holster

Attach the open end of the Cold Water Braided Metal

Bidet Hose to the incoming water connection on the

side of the holster.

3. Connect Hand-Held Bidet Sprayer to Holster

a. Connect your hand-held bidet sprayer to the

sprayer hose.

b. Connect the open end of the sprayer hose to the ½"

connection at the bottom of the holster.

c. Place the hand-held bidet sprayer in the holster slot.

4. Turn on Water Supply & Check for Leaks

a. Open the main water supply valve slowly and check

for leaks.

b. Wait 5-10 minutes, check again, and if there are no

leaks, continue.

Step 1a

Step 1b

Step 2

Step 3b

NOTE: If there is any leaking, check all rubber washers

and make sure all water connections are tight and

secure. If necessary, you can use plumbers tape for any

leaking connections.

7

Using the Hand-Held Bidet Holster with Integrated Shut O

PRODUCT OPERATION

To engage your hand-held bidet, turn on the

integrated shut o faucet handle located on the

metal holster.

Remove the sprayer from the holster and use in

normal fashion.

When ﬁnished, replace the sprayer in the holster

and turn o the integrated shut o faucet handle.

WARNING: The faucet handle must be turned o after each use.

Failure to turn o after each use may cause ﬂooding and water damage.

On

O

8

Maintenance

TECHNICAL INFORMATION

To clean the Hand-Held Bidet Holster with

Integrated Shut O, use a mild cleaner such as

Simple Green or Windex spray. Do not scrub

or use harsh, abrasive products to clean the

Hand-Held Bidet Holster with Integrated Shut

O, which may scratch the product.

Short Term Non-Use

If the product will not be used for more than

a few weeks, you may consider shutting the

water supply o at the wall as an additional

precaution.

9

NOTE: The speciﬁcations listed above are subject to change without prior notice for reasons of improving

the product performance.

HANDHELD BIDET HOLSTER WITH INTEGRATED SHUT OFF

Models MBH10, MBH37, MBH40

Supply Water Pressure 20 psi–100 psi / 0.14 MPa–0.69 MPa

Incoming Water Temperature Range 32 °F–158 °F / 0 °C–70 °C

Product Dimension 15.75 in x 2.24 in / 40 cm x 6 cm

Product Thickness 0.08 in / 0.2 cm

Product Weight

MBH10: 1.14 lb / 0.7 kg

MBH37: 2.23 lb / 1.02 kg

MBH40: 2.29 lb / 1.04 kg

TECHNICAL INFORMATION

Product Speciﬁcations

10

Warranty

TECHNICAL INFORMATION

Brondell products are backed by some of the most comprehensive warranties in the industry. Brondell

warrants that all products (excluding consumable items) shall be free from defects in material and

workmanship under normal use and service.

MBH-10/MBH-37/MBH-40 RESIDENTIAL ONE-YEAR LIMITED WARRANTY

100% Coverage of all parts and labor for the entire product for the ﬁrst year from original date of purchase.

MBH-10/MBH-37/MBH-40 COMMERCIAL WARRANTY

Warranty period 1 year from original purchase date for all Brondell products. Warranties may not apply to

products that are used for heavy commercial, hospital, or other high use non-residential applications.

EXCLUSIONS AND LIMITATIONS

1. Brondell warrants its products to be free from manufacturing defects under normal use and service. This

warranty is extended only to the ORIGINAL PURCHASER.

2. Brondell’s obligations under this warranty are limited to repairs or replacement, at Brondell’s option, of

products or parts found to be defective, provided that such products were properly installed and used in

accordance with instructions. Brondell reserves the right to make such inspections as may be necessary

in order to determine the cause of the defect.

3. Brondell is not responsible for the cost of removal, return (shipping) and/or re-installation of products.

This warranty does NOT apply to:

• Damage or loss which occurs during shipment.

• Damage or loss sustained through any natural or man-made causes beyond the control of

Brondell, including but not limited to ﬁre, earthquake, ﬂoods, etc.

• Damage or loss resulting from sediments or foreign matter contained in a water system.

• Damage or loss resulting from negligent or improper installation including installation of a unit in a

harsh or hazardous environment.

• Damage or loss resulting from removal, improper repair, modiﬁcation of the product, or improper

maintenance including damage caused by chlorine or chlorine related products.

4. This warranty gives you speciﬁc legal rights. You may have other rights which vary from state to state.

THIS WRITTEN WARRANTY IS THE ONLY WARRANTY MADE BY BRONDELL. REPAIR OR REPLACEMENT

AS PROVIDED UNDER THIS WARRANTY SHALL BE THE EXCLUSIVE REMEDY AVAILABLE TO THE

PURCHASER. BRONDELL SHALL NOT BE RESPONSIBLE FOR LOSS OF USE OF THE PRODUCT OR FOR

OTHER INCIDENTAL, SPECIAL, FOR CONSEQUENTIAL DAMAGES OR EXPENSES INCURRED BY THE

PURCHASER OR FOR LABOR OR OTHER COSTS DUE TO INSTALLATION OR REMOVAL OR COSTS OF

REPAIRS BY OTHERS, OR FOR ANY OTHER EXPENSE NOT SPECIFICALLY STATED ABOVE. EXCEPT

TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ANY IMPLIED WARRANTIES, INCLUDING THAT OF

MERCHANTABILITY, ARE EXPRESSLY LIMITED TO THE DURATION OF THIS WARRANTY. SOME STATES

DO NOT ALLOW LIMITATIONS, SO THE ABOVE LIMITATION AND EXCLUSION MAY NOT APPLY TO YOU.

HOW TO OBTAIN SERVICE

To obtain repair service under this warranty, you must contact an authorized Brondell Service Center to

obtain an RMA (Return Merchandise Authorization) number. Proof of purchase in the form of a copy of the

original receipt must accompany the returned unit for the warranty to be valid. Take or ship the unit pre-

paid to the closest Brondell authorized service center along with the RMA number and proof of purchase.

To obtain the RMA number and locate the Brondell Service Center location nearest you, please call 1-888-

542-3355, Mon–Fri, 9am–5pm PST.

11

CONTACT:

Brondell, Inc.

PO Box 470085

San Francisco, CA 94147-0085

Email: [email protected]

Web: www.brondell.com

For questions, contact

Brondell Customer Service:

1-888-542-3355

Monday – Friday

9am – 5pm PST

MANUFACTURED BY:

Brondell, Inc.

PO Box 470085

San Francisco, CA 94147-0085

Made in China

Please retain receipt records for any

warranty claims.

12

Indices

MANUAL DE INSTRUCCIONES DEL MBH10/MBH37/MBH40

Este manual contiene información de seguridad

importante. Lea este manual atentamente antes de

utilizar su Hand-Held Bidet Holster with Integrated Shut

O y guárdelo para futuras consultas.

13

14

15

INFORMACIÓN DEL PRODUCTO

Características del producto

Dimensiones del producto

Piezas del producto

16

17

INSTALACIÓN DEL PRODUCTO

Antes de la instalación

Instalación

19

FUNCIONAMIENTO DEL PRODUCTO

Uso de Hand-Held Bidet Holster with

Integrated Shut O

20 MANTENIMIENTO

21 ESPECIFICACIONES DEL PRODUCTO

22 GARANTÍA

23 CONTACTO

01 INGLÉS

24 FRANCÉS

INFORMACIÓN GENERAL

INSTALACIÓN DEL PRODUCTO

FUNCIONAMIENTO DEL

PRODUCTO

TRADUCCIONES

INFORMACIÓN TÉCNICA

13

Montaje para rociador de bidé manual de acero

inoxidable pulido

Mango cromado e integrado de cierre de agua

La funda universal para el rociador de mano funciona

con cualquier rociador

Válvula en T de ⅞" de metal de alta calidad

Manguera de agua fría de metal trenzado resistente

No se necesita suministro de electricidad ni baterías

Instalación sencilla y ajuste adaptable al inodoro

Garantía de un año

Características del producto

INFORMACIÓN DEL PRODUCTO

14

Dimensiones del producto

INFORMACIÓN DEL PRODUCTO

5,69cm 5cm

40cm

30cm

8cm

0,20cm de ancho

1,14cm

15

Piezas del producto

INFORMACIÓN DEL PRODUCTO

1. Montaje de acero inoxidable

2. Manguera de agua fría de metal trenzado

1. Cabeza del rociador del bidé

2. Manguera rociadora de metal (½" x ½")

3. Arandela grande de goma (1)

4. Conector de agua fría de válvula en T

(⅞" x ⅞" x ⅜")

1

2

3

4

Solo para el MBH-37/MBH-40

16

Debe tener un bidé manual CleanSpa o un producto

equivalente con una manguera rociadora de conexión de

½" para instalar Hand-Held Bidet Holster with Integrated

Shut O.

IMPORTANTE

Tenga en cuenta que la válvula en T para agua fría

provista se debe instalar en la válvula de llenado debajo

del tanque del inodoro, NO en la entrada del suministro

de agua fría que sale de la pared.

Revisar la línea de suministro de agua

Si la tubería que conecta la válvula de llenado del tanque

del inodoro con la válvula de corte en la pared es rígida,

deberá comprar una manguera ﬂexible de suministro

de agua para reemplazarla antes de instalar Hand-

Held Bidet Holster with Integrated Shut O. El largo de

la manguera puede variar y el tamaño de la conexión

superior debe ser para una válvula de ﬂotador de ⅞"

para conectarla a la válvula en T que instalará debajo del

tanque del inodoro; la conexión inferior variará (las más

comunes son de compresión hembra de ⅜" y ½").

Antes de la instalación

INSTALACIÓN DEL PRODUCTO

INCORRECTO

Suministro de

agua fría

Llenar la

válvula

CORRECTO

17

Instalación

INSTALACIÓN DEL PRODUCTO

Lea atentamente estas instrucciones antes de instalar su

Hand-Held Bidet Holster with Integrated Shut O. De lo

contrario, podrían surgir problemas, como acumulación

de agua, fugas o daños al producto.

1. Cómo retirar el asiento del inodoro existente

a. Levante las tapas de las bisagras y use un

destornillador de cabeza plana o Phillips para quitar

los pernos de montaje. De manera alternativa, es

posible que deba aﬂojar los pernos de montaje que

se encuentran debajo del asiento.

b. Retire el asiento del inodoro y déjelo a un lado,

junto con los pernos y las herramientas.

2. Cierre la válvula de suministro de agua y descargue el

inodoro.

a. Cierre la válvula de suministro de agua para

detener el ﬂujo de agua.

b. Descargue el inodoro y mantenga la manija

presionada para que el tanque se vacíe por

completo.

c. Desconecte la manguera del suministro de agua del

tanque del inodoro.No la desconecte de la válvula

de suministro de agua.

d. Si ya tiene un rociador de bidé manual conectado al

tanque del inodoro, retire la válvula en T existente

y la manguera de conexión del rociador de bidé

manual.

3. Conecte la válvula en T de agua fría a la válvula de

llenado del tanque del inodoro

a. Instale la válvula en T de ⅞" de la entrada de

agua fría incluida con la arandela de goma grande

incluida en la conexión de agua entrante en la parte

inferior del tanque del inodoro.

b. Conecte la línea de suministro de agua fría que

viene de la pared a la parte inferior de la válvula T.

4. Conecte la manguera de agua fría a la válvula en T

Conecte un extremo de la manguera de metal

trenzado para agua fría al extremo libre de la válvula

en T instalada.

Paso 3a

Paso 3b

Paso 1b

Paso 2c

Paso 4

18

Instalación

INSTALACIÓN DEL PRODUCTO

Instalación de la funda de bidé manual

1. Instale la funda de bidé manual en el inodoro

a. Coloque la funda de bidé manual en el inodoro de

modo que las ranuras de montaje queden alineadas

con los oriﬁcios del accesorio del inodoro.

b. Vuelva a colocar el asiento del inodoro en la parte

superior de la funda de bidé manual y asegúrelo

con los materiales originales del asiento del inodoro.

Asegúrese de ajustarlos para que la funda y el

asiento no se muevan.

2. Conecte la manguera de agua fría a la funda de bidé

manual

Conecte el extremo libre de la manguera de bidé de

metal trenzado de agua fría a la conexión de agua

entrante en el lateral de la funda.

3. Conecte el rociador de bidé manual a la funda

a. Conecte el rociador de bidé manual a la manguera

rociadora.

b. Conecte el extremo libre de la manguera rociadora a

la conexión de ½" en la parte inferior de la funda.

c. Coloque el rociador de bidé manual en la abertura

de la funda.

4. Encienda el suministro de agua y veriﬁque si hay fugas

a. Abra lentamente la válvula principal de suministro de

agua y compruebe si hay fugas.

b. Espere de 5 a 10 minutos, vuelva a veriﬁcar y, si no

hay fugas, continúe.

Paso 1a

Paso 1b

Paso 2

Paso 3b

NOTA: Si hay alguna fuga, revise todas las arandelas de

goma y asegúrese de que todas las conexiones de agua

estén ajustadas y seguras. Si es necesario, puede usar

cinta de teﬂón para las conexiones con fugas.

La page charge ...

brondell MBH-10 Hand-Held Bidet Holster Integrated Shut Off Le manuel du propriétaire

Ce manuel convient également à

brondell MBH-10 Hand-Held Bidet Holster Integrated Shut Off Le manuel du propriétaire

dans d''autres langues

Documents connexes