Blomberg KQD 1360E Manuel utilisateur

Bedienungsanleitung

Operating instructions

Refrigerator

Kühlschrank

Réfrigérateur

KQD 1360X

KQD 1360E

KQD 1360 X A+

KQD 1360 E A+

KQD 1360 X A++

Køleskab

Frigorífico

لاچخی

Jääkaappi

Kylskåp

Холодильник

Ψυγείο

Хладилник

EN

1

Please read this manual first!

Dear Customer,

We hope that your product, which has been produced in modern plants and

checked under the most meticulous quality control procedures, will provide you an

effective service.

For this, we recommend you to carefully read the entire manual of your product

before using it and keep it at hand for future references.

This manual

• Will help you use your appliance in a fast and safe way.

• Read the manual before installing and operating your product.

• Follow the instructions, especially those for safety.

• Keep the manual in an easily accessible place as you may need it later.

• Besides, read also the other documents provided with your product.

Please note that this manual may be valid for other models as well.

Symbols and their descriptions

This instruction manual contains the following symbols:

C Important information or useful usage tips.

A Warning against dangerous conditions for life and property.

B Warning against electric voltage.

This product is supplied with the selective sorting symbol for waste electrical

and electronic equipment (WEEE).

This means that this product must be handled pursuant to European Directive

2002/96/EC in order to be recycled or dismantled to minimise its impact on

the environment. For further information, please contact your local or regional

authorities.

Electronic products not included in the selective sorting process are potentially

dangerous for the environment and human health due to the presence of

hazardous substances.

Recycling

EN

2

1 The refrigerator 3

2 Important Safety Warnings 4

Intended use ..................................... 4

For products with a water dispenser; .6

Child safety ........................................6

HCA Warning ....................................6

Things to be done for energy saving ..6

3 Installation 7

Points to be considered when re-

transporting your refrigerator ............. 7

Before operating your refrigerator ......7

Electric connection ............................8

Disposing of the packaging ............... 8

Disposing of your old refrigerator .......8

Placing and Installation ......................8

Floor balance adjustment ..................9

Adjusting the gap between the upper

door ..................................................9

Installing Water Filter .......................11

Connection of the Water Pipe to the

Refrigerator .....................................11

Connection of Water Hose to the

Jug .................................................12

Connection of the Water Pipe to the

Cold Water Mains Line ....................13

Prior to first use of Water Dispenser .15

4 Preparation 16

CONTENTS

5 Using your refrigerator 17

Indicator Panel .................................17

Things to do to have the filter usage

time calculated automatically ...........21

Sliding Body Shelves .......................22

Egg tray ...........................................22

Crisper ............................................22

Chiller compartment ........................22

Movable Middle Section ................. 23

Flexi Zone Storage Compartment ..23

Blue light .........................................23

Sliding Body Shelves With Rear

Hangers ..........................................24

Butter & Cheese Section ................. 24

Using the water spring ..................... 24

Spillage Tray ....................................24

Minibar ............................................ 25

6 Cleaning and care 26

Protection of plastic surfaces .......... 26

7 Recommended solutions

for the problems 27

EN

3

17

18 19

2

3

6

7

8

9

5

4

16

13

11

14

1

12

10

15

1 The refrigerator

1- Fridge compartment door shelves

2- Fridge compartment glass shelves

3- Diffuser cover

4- Illumination lens

5- Movable middle section

6- Chiller compartment

7- Crisper

8- Icematic

9- Frozen food storage compartments

10- Minibar

11- Bottle holder

12- Bottle shelf

13- Food storage compartment shelves

14- Food storage compartments

15- Water Filter

16- Butter & Cheese shelf

17- Fridge compartment

18- Freezer compartment

19- Flexi Zone

C Figures that take place in this instruction manual are schematic and may not

correspond exactly with your product. If the subject parts are not included in the

product you have purchased, then it is valid for other models.

EN

4

2 Important Safety Warnings

Please review the following information.

Failure to observe this information may

cause injuries or material damage.

Otherwise, all warranty and reliability

commitments will become invalid.

The usage life of the unit you purchased

is 10 years. This is the period for keeping

the spare parts required for the unit to

operate as described.

Intended use

This product is intended to be used

– indoors and in closed areas such as

homes;

– in closed working environments such

as stores and offices;

– in closed accommodation areas such

as farm houses, hotels, pensions.

• This product should not be used

outdoors.

General safety

• When you want to dispose/scrap the

product, we recommend you to consult

the authorized service in order to learn

the required information and authorized

bodies.

• Consult your authorized service for all

your questions and problems related to

the refrigerator. Do not intervene or let

someone intervene to the refrigerator

without notifying the authorised

services.

• For products with a freezer

compartment; Do not eat cone ice

cream and ice cubes immediately

after you take them out of the freezer

compartment! (This may cause frostbite

in your mouth.)

• For products with a freezer

compartment; Do not put bottled and

canned liquid beverages in the freezer

compartment. Otherwise, these may

burst.

• Do not touch frozen food by hand; they

may stick to your hand.

• Unplug your refrigerator before cleaning

or defrosting.

• Vapor and vaporized cleaning materials

should never be used in cleaning

and defrosting processes of your

refrigerator. In such cases, the vapor

may get in contact with the electrical

parts and cause short circuit or electric

shock.

• Never use the parts on your refrigerator

such as the door as a means of

support or step.

• Do not use electrical devices inside the

refrigerator.

• Do not damage the parts, where the

refrigerant is circulating, with drilling or

cutting tools. The refrigerant that might

blow out when the gas channels of the

evaporator, pipe extensions or surface

coatings are punctured causes skin

irritations and eye injuries.

• Do not cover or block the ventilation

holes on your refrigerator with any

material.

• Electrical devices must be repaired

by only authorised persons. Repairs

performed by incompetent persons

create a risk for the user.

• In case of any failure or during a

maintenance or repair work, disconnect

your refrigerator’s mains supply by

either turning off the relevant fuse or

unplugging your appliance.

• Do not pull by the cable when pulling

off the plug.

• Place the beverage with higher proofs

tightly closed and vertically.

• Never store spray cans containing

flammable and explosive substances in

the refrigerator.

• Do not use mechanical devices

EN

5

or other means to accelerate the

defrosting process, other than those

recommended by the manufacturer.

• This product is not intended to be

used by persons with physical, sensory

or mental disorders or unlearned

or inexperienced people (including

children) unless they are attended by

a person who will be responsible for

their safety or who will instruct them

accordingly for use of the product

• Do not operate a damaged refrigerator.

Consult with the service agent if you

have any concerns.

• Electrical safety of your refrigerator shall

be guaranteed only if the earth system

in your house complies with standards.

• Exposing the product to rain, snow, sun

and wind is dangerous with respect to

electrical safety.

• Contact authorized service when there

is a power cable damage to avoid

danger.

• Never plug the refrigerator into the wall

outlet during installation. Otherwise, risk

of death or serious injury may arise.

• This refrigerator is intended for only

storing food items. It must not be used

for any other purpose.

• Label of technical specifications is

located on the left wall inside the

refrigerator.

• Never connect your refrigerator to

electricity-saving systems; they may

damage the refrigerator.

• If there is a blue light on the refrigerator,

do not look at the blue light with optical

tools.

• For manually controlled refrigerators,

wait for at least 5 minutes to start the

refrigerator after power failure.

• This operation manual should be

handed in to the new owner of the

product when it is given to others.

• Avoid causing damage on power cable

when transporting the refrigerator.

Bending cable may cause fire. Never

place heavy objects on power cable.

Do not touch the plug with wet hands

when plugging the product.

• Do not plug the refrigerator if the wall

outlet is loose.

• Water should not be sprayed directly on

inner or outer parts of the product for

safety purposes.

• Do not spray substances containing

inflammable gases such as propane

gas near the refrigerator to avoid fire

and explosion risk.

• Never place containers filled with water

on top of the refrigerator, otherwise this

may cause electric shock or fire.

• Do not overload your refrigerator

with excessive amounts of food. If

overloaded, the food items may fall

down and hurt you and damage

refrigerator when you open the door.

Never place objects on top of the

refrigerator; otherwise, these objects

may fall down when you open or close

the refrigerator's door.

• As they require a precise temperature,

vaccines, heat-sensitive medicine and

scientific materials and etc. should not

be kept in the refrigerator.

• If not to be used for a long time,

refrigerator should be unplugged. A

possible problem in power cable may

cause fire.

• The plug's tip should be regularly

cleaned; otherwise, it may cause fire.

• The plug’s tip should be cleaned

EN

6

regularly with a dry cloth; otherwise,

it may cause fire.

• Refrigerator may move if adjustable

legs are not properly secured on the

floor. Properly securing adjustable

legs on the floor can prevent the

refrigerator to move.

• When carrying the refrigerator,

do not hold it from door handle.

Otherwise, it may be snapped.

• When you have to place your

product next to another refrigerator

or freezer, the distance between

devices should be at least 8cm.

Otherwise, adjacent side walls may

be humidified.

For products with a water

dispenser;

Pressure of water mains should be

minimum 1 bar. Pressure of water

mains should be maximum 8 bars.

• Use only potable water.

Child safety

• If the door has a lock, the key should

be kept away from reach of children.

• Children must be supervised to

prevent them from tampering with

the product.

HCA Warning

If your product's cooling system

contains R600a:

This gas is flammable. Therefore, pay

attention to not damaging the cooling

system and piping during usage

and

transportation. In the event of damage,

keep your product away from potential

fire sources that can cause the product

catch a fire and ventilate the room in

which the unit is placed.

Ignore this warning if your product's

cooling system contains R134a.

Type of gas used in the product is stated

in the type plate which is on the left wall

inside the refrigerator.

Never throw the product in fire for

disposal.

Things to be done for energy

saving

• Do not leave the doors of your

refrigerator open for a long time.

• Do not put hot food or drinks in your

refrigerator.

• Do not overload your refrigerator so

that the air circulation inside of it is not

prevented.

• Do not install your refrigerator under

direct sunlight or near heat emitting

appliances such as ovens, dishwashers

or radiators.

• Pay attention to keep your food in

closed containers.

• For products with a freezer

compartment; You can store maximum

amount of food items in the freezer

when you remove the shelf or drawer

of the freezer. Energy consumption

value stated for your refrigerator has

been determined by removing freezer

shelf or drawer and under maximum

load. There is no harm to use a shelf or

drawer according to the shapes and

size of food to be frozen.

• Thawing frozen food in fridge

compartment will both provide energy

saving and preserve the food quality.

EN

7

3 Installation

C Please remember that the manufacturer

shall not be held liable if the information

given in the instruction manual is not

observed.

Points to be considered

when re-transporting your

refrigerator

1. Your refrigerator must be emptied and

cleaned prior to any transportation.

2. Shelves, accessories, crisper and etc.

in your refrigerator must be fastened

securely by adhesive tape against any

jolt before repackaging.

3. Packaging must be tied with thick

tapes and strong ropes and the rules of

transportation printed on the package

must be followed.

C Always remember...

Every recycled material is an

indispensable source for the nature and

for our national resources.

If you wish to contribute to recycling the

packaging materials, you can get further

information from the environmental

bodies or local authorities.

Before operating your

refrigerator

Before starting to use your refrigerator

check the following:

1. Is the interior of the refrigerator dry and

can the air circulate freely in the rear of

it?

2. Insert the 2 plastic wedges onto the

rear ventilation cover as illustrated in

the following figure. To do this, remove

the screws on the product and use the

screws given in the same pouch.

Plastic wedges will provide the required

distance between your refrigerator

and the wall in order to allow the air

circulation.

3. Clean the interior of the refrigerator as

recommended in the “Maintenance and

cleaning” section.

4. Plug the refrigerator into the wall outlet.

When the door is open the respective

interior light will come on.

5. You will hear a noise as the compressor

starts up. The liquid and gases sealed

within the refrigeration system may

also give rise to noise, even if the

compressor is not running and this is

quite normal.

6. Front edges of the refrigerator may

feel warm. This is normal. These areas

are designed to be warm to avoid

condensation.

EN

8

Electric connection

Connect your refrigerator to a grounded

socket which is being protected by a

fuse with the appropriate capacity.

Important:

B The connection must be in compliance

with national regulations.

B The power cable plug must be easily

accessible after installation.

B Voltage and allowable fuse protection

are specified in the “Technical

Specifications” section.

BThe specified voltage must be equal to

your mains voltage.

B Extension cables and multiway plugs

must not be used for connection.

B A damaged power cable must be

replaced by a qualified electrician.

B The appliance must not be operated

before it is repaired! There is danger of

electric shock!

Disposing of the packaging

A The packing materials may be

dangerous for children. Keep the

packing materials out of the reach

of children or dispose them of by

classifying them in accordance

with the waste instructions. Do not

dispose them of along with the normal

household waste.

The packing of your refrigerator is

produced from recyclable materials.

Disposing of your old

refrigerator

Dispose of your old machine without

giving any harm to the environment.

A You may consult your authorized dealer

or waste collection center of your

municipality about the disposal of your

refrigerator.

A Before disposing of your refrigerator,

cut out the electric plug and, if there

are any locks on the door, make them

inoperable in order to protect children

against any danger.

Placing and Installation

B Caution: Never plug the refrigerator

into the wall outlet during installation.

Otherwise, risk of death or serious injury

may arise.

A If the entrance door of the room

where the refrigerator will be installed is

not wide enough for the refrigerator to

pass through, than call the authorised

service to have them remove the doors

of your refrigerator and pass it sideways

through the door.

1. Install your refrigerator to a place that

allows ease of use.

2. Keep your refrigerator away from

heat sources, humid places and direct

sunlight.

3. There must be appropriate air

ventilation around your refrigerator in

order to achieve an efficient operation.

If the refrigerator is to be placed in a

recess in the wall, there must be at least

5 cm distance with the ceiling and at

least 5 cm with the wall.

If the floor is covered with a carpet, your

product must be elevated 2.5 cm from

the floor.

4. Place your refrigerator on an even

floor surface to prevent jolts.

5. Do not keep your refrigerator in

ambient temperatures under 10°C.

EN

9

Floor balance adjustment

AIf your refrigerator is unbalanced;

B First unplug the product. The product

must be unplugged when making the

balance adjustment. There is the risk of

electric shock.

4

1 2 3

1- Ventilation cover is removed by

unscrewing its screws as illustrated in

the figure before the procedure. You

can balance your refrigerator by turning

the front legs of it as illustrated in the

figure. The corner where the leg exists is

lowered when you turn in the direction of

black arrow and raised when you turn in

the opposite direction. Taking help from

someone to slightly lift the refrigerator will

facilitate this process.

2. After the balance issue is remedied,

install back the ventilation cover and

fasten the screws.

3. Remove the screws fastening the

lower ventilation cover using a Philips

screwdriver.

Adjusting the gap between

the upper door

C You can adjust the gap between the

fridge compartment doors as illustrated

in the figures.

Door shelves should be empty when

adjusting the door height.

C Using a screwdriver, remove the

screw of upper hinge cover of the door

you want to adjust.

EN

10

C Adjust the door appropriately as you

desire by loosing the screws.

C Fix the door you have adjusted by

tightening the screws without changing

the position of the door.

C Replace the hinge cover and fix with

the screw.

EN

11

Installing Water Filter

(in some models)

Two different water sources may

be connected to the refrigerator for

water supply: the mains cold water

supply and water in a jug.

Installation Requirements

A pump should be used for jug water

usage.

Check that the parts stated below are

supplied with your appliance.

1. Union for connection of the water

pipe to the rear of the appliance. (If it

does not fit, provide it from the nearest

authorized service.)

2. 2 pieces of pipe clips (In case required

to secure the water pipe)

Note: Since the following parts are not

required in use with a jug, they may not

be found in the product you purchased.

3. 5-meter long water pipe (1/4 inch in

diameter)

4. Cold mains water valve with mesh filter

(Tap Adapter)

5. Water Filter or externally connectable

filter to be fitted to the bracket inside

the fridge compartment.

Place where the external filter is going to

be fitted should be determined first.

(Applies to the filter being used outside

the refrigerator.) Then, determine the

distance between the filter and the

refrigerator and required hose lengths

from the filter to the refrigerator water

inlet.

Water filter must be hold upright as shown

in the figure. It is important to properly

attach the filter to water inlet and water

outlet points.

After attaching the filter, do not use first 3-4

glasses of water.

Connection of the Water

Pipe to the Refrigerator

1. After installing the union onto the

water pipe, insert the water pipe to

the refrigerator inlet valve by pressing

downwards firmly.

2. Fix union as seen in the opposite

figure, by squeezing by hand on the

refrigerator inlet valve.

(a- Water Pipe, b-Union, c-Valve)

C Note 1: You should not need to

tighten the union with a tool to achieve

water tight assembly. In case of a leak

use a spanner or a pair of pliers to

tighten the union.

3

1

4

2

5

c

a

b

1

2

EN

12

Connection of Water Hose to

the Jug

(in some models)

To connect water to the refrigerator from

a jug, a pump is needed. Follow the

instructions below after connecting one

end of the water pipe coming out of the

pump to the refrigerator as described on

the previous page.

1. Finish the connection by pushing the

other end of the water pipe into the

water pipe inlet of the pump as shown

in the figure.

2

1a

1b

2. Put and fix the pump hose into the jug

as shown in the figure.

3. After completing the connection, plug in

and run the pump.

To provide an efficient operation of the

pump, wait for 2-3 minutes after

starting the pump.

C You may refer to the user manual

of the pump while making the water

connection.

C There is no need to use water filter in

case a jug is used.

C Pump must be used when jug will be

used.

EN

13

Connection of the Water

Pipe to the Cold Water Mains

Line

(in some models)

If you want to use your refrigerator by

connecting it to the cold water mains

line,

you will have to connect a standard 1/2"

valve connection fitting to the cold water

supply in your house. In case this valve is

not present or in case you are not sure,

consult a qualified plumber.

1. Separate the union from the tap

adaptor. (Figure A)

2. Install the tap adaptor to 1/2” valve

fitting as shown in the figure. (Figure B)

3. After inserting the water pipe to the

union, install it to the tap adaptor and

insert to the tap as shown in the figure.

(Figure C)

4. Tighten the union manually. In case of a

leak use a spanner or a pair of pliers to

tighten the union.

A Caution: Secure the water pipe

to suitable points by means of the

pipe clips supplied to avoid any

damage or displacement or accidental

disconnection.

A Caution: After turning on the water

valve, make sure that there is no leakage

at both connection points of the water

pipe. In case of a leak, turn off the valve

immediately and tighten all joints again

using a spanner or a pair of pliers.

A Caution: Make sure that standard

1/2" valve fitting fed by cold mains water

supply is available and is turned off fully.

EN

14

To fit the water filter follow the

instructions below referring to figures

supplied:

1. Press ice cancel button on the display.

2. Remove the filter cover in the fridge

compartment by pulling it forward.

3. Take out the water filter by-pass cover

by rotating it downwards.

A Caution: Make sure that the “Ice off”

mode is active before taking out the by-

pass cover.

Note: It is normal that a few drops of

water drip after the cover has been taken

out.

4. Remove the lid on top of the water filter

to place it as shown in the figure and

turn upwards to lock it.

5. Press ice cancel button on the display

again to exit from this mode.

Water filter should be replaced every 6

months.

If you want to have the filter change time

calculated automatically and receive a

warning at the end of usage time, please

read "Calculating the Filter Usage Time

Automatically" section.

EN

15

The water filter must be removed as

shown in the figure when it is going to

be replaced or when it will no longer

be used and by-pass cover must be

attached. It must be made sure that Ice

Off mode is active before taking it out.

A Caution: Water filter cleans some

foreign particles in the water. It does not

purify water from microorganisms.

A Caution: Ice Off button must always

be pressed during replacement of the

water filter or installing the by-pass

cover.

Prior to first use of Water

Dispenser

C Water mains pressure must not be

below 1 bar.

C Water mains pressure must not be

above 8 bars.

C Pumps must be used in case the

supply water pressure drops below 1 bar

or if a jug is going to be used.

C Water system of the refrigerator must

be connected to the cold water line. It

must not be connected to hot water line.

C No water may be obtained in the

initial operation of the refrigerator. This

is caused by the air in the system. To

discharge air from the system, press

Dispenser latch for periods of 1 minute

until water comes from the Dispenser.

Water flow may be irregular in the

beginning. Irregular water flow will be

normalized after the air in the system is

discharged.

C At the initial startup of the refrigerator

approx.12 hours must pass before cold

water can be obtained.

C Water mains pressure must be

between 1-8 bars for the operation of

Ice/Water Dispenser smoothly. For this,

check that 1 glass of water (100 cc) can

be filled in 10 seconds.

C The first 10 glasses of water should

not be consumed.

C Approximately the first 30 cubes

of ice to be obtained from the Ice

Dispenser must not be used.

C Always use the water filter when a jug

is not being used.

EN

16

4 Preparation

C Your refrigerator should be installed at

least 30 cm away from heat sources

such as hobs, ovens, central heater

and stoves and at least 5 cm away

from electrical ovens and should not be

located under direct sunlight.

C The ambient temperature of the room

where you install your refrigerator

should at least be 10°C. Operating your

refrigerator under cooler conditions

than this is not recommended with

regard to its efficiency.

C Please make sure that the interior of

your refrigerator is cleaned thoroughly.

C If two refrigerators are to be installed

side by side, there should be at least 2

cm distance between them.

C When you operate your refrigerator

for the first time, please observe the

following instructions during the initial

six hours.

- The door should not be opened

frequently.

- It must be operated empty without

any food in it.

- Do not unplug your refrigerator. If

a power failure occurs out of your

control, please see the warnings in

the “Recommended solutions for the

problems” section.

C Original packaging and foam

materials should be kept for future

transportations or moving.

EN

17

1 7 11 12 15 4

5

6

2

3

16

17

18 20 19

10 9 14 138

5 Using your refrigerator

Indicator Panel

This touch-control indicator panel allows you to set the temperature without opening

the door of your refrigerator. Just touch the relevant button with your finger to set the

temperature.

1. Eco Extra/Vacation Button

2. Fast Freeze Button

3. Freezer Compartment Temperature

Setting Button

4. Fridge Compartment Temperature

Setting Button

5. Quick Cool Button

6. Flexi Zone Compartment Temperature

Setting Button

7. Vacation Function Indicator

8. Eco Extra Function Indicator

9. Quick Freeze Function Indicator

10. Freezer Compartment Temperature

Indicator

11. Fridge Compartment Temperature

Indicator

12. Quick Cool Function Indicator

13. Flexi Zone Storage Compartment

Temperature Indicator

14. Economy Mode Indicator

15. Error Status Indicator

16. Key Lock Indicator

17. Ice Cancel Button

18. Ice Off indicator

19. Cancel Filter Change Warning Button

20. Filter Change Warning Indicator

EN

18

1. Eco Extra/Vacation Button

Press this button briefly to activate the

Eco Extra function. Press and hold this

button for 3 sec. to activate the Vacation

function. Press this button again to

deactivate the selected function.

2. Fast Freeze Button

Press this button briefly to activate the

Fast Freeze function. Press this button

again to deactivate the selected function.

3. Freezer Compartment

Temperature Setting Button

Press this button to set the temperature

of the freezer compartment to -18, -20,

-22, -24, -18... respectively. Press this

button to set the desired temperature for

the Freezer Compartment.

4. Fridge Compartment Temperature

Setting Button

Press this button to set the temperature

of the fridge compartment to 8, 6, 4, 2,

8... respectively. Press this button to set

the desired temperature for the Fridge

Compartment.

5. Quick Cool Button

Press this button briefly to activate the

Quick Cool function. Press this button

again to deactivate the selected function.

6. Flexi Zone Compartment

Temperature Setting Button

You can set the Flexi Zone Compartment

either as a Freezer or a Cooler.

Press and hold this button for a long

time (3 sec) to set the Flexi Zone

Compartment as a Freezer or a Cooler.

This compartment is set as a Freezer

Compartment at factory.

If the Flexi Zone Compartment is set as a

Freezer, then the temperature of the Flexi

Zone Compartment will change as -18,

-20, -22, -24, -18... respectively each

time you press this button. If the Flexi

Zone Compartment is set as a Fridge,

then the temperature of the Flexi Zone

Compartment will change as 10, 8, 6,

4, 2, 0, -6, ... respectively each time you

press this button.

7. Vacation Function Indicator

Indicates that the vacation function

is active. If this function is active,

"- -" appears on the indicator of the

fridge compartment and no cooling is

performed in the fridge compartment.

Other compartments will be cooled in

accordance with the temperature set for

them.

Press the relevant button again to

deactivate this function.

8. Eco Extra Function Indicator

It indicates that the Eco-Extra function

is active. If this function is active, your

refrigerator will automatically detect

the least usage periods and energy-

efficient cooling will be performed during

those times. Economy indicator will be

active while energy-efficient cooling is

performed.

Press the relevant button again to

deactivate this function.

EN

19

9. Quick Freeze Function Indicator

It indicates that the Fast Freeze function

is active. Use this function when

you place fresh food into the freezer

compartment or when you need ice.

When this function is active, your

refrigerator will run for a certain period of

time.

Press the relevant button again to

deactivate this function.

10. Freezer Compartment

Temperature Indicator

It indicates the temperature set for

Freezer Compartment.

11. Fridge Compartment

Temperature Indicator

Indicates the temperature set for Fridge

Compartment.

12. Quick Cool Function Indicator

Indicates that the Quick Cool function is

active. Use this function when you place

fresh food into the fridge compartment

or when you need to cool your food

quickly. When this function is active, your

refrigerator will run for 2 hours without

stopping.

Press the relevant button again to

deactivate this function.

13. Flexi Zone Storage Compartment

Temperature Indicator

It indicates the temperature set for Flexi

Zone compartment.

14. Economy Mode Indicator

Indicates that the refrigerator is running

in energy-efficient mode. Freezer

Compartment temperature

This indicator will be active if the function

is set to -18 or the energy efficient

cooling is being performed due to Eco-

Extra function.

15. Error Status Indicator

If your refrigerator does not cool

adequately or if there is a sensor failure,

this indicator will be activated. When this

indicator is active, Freezer Compartment

Temperature indicator will display "E"

and Fridge Compartment Temperature

Indicator will display numbers such

as "1,2,3…". These numbers on the

indicator provides information about the

error to the service personnel.

16. Key Lock Indicator

Use this function if you do not want your

refrigerator temperature setting changed.

Press Quick Cool Button and Flexi Zone

Compartment Temperature Setting

Button simultaneously for a long time (3

sec) to activate this feature.

Press the relevant buttons again to

deactivate this function.

17. Ice Cancel Button

To stop ice formation, ice cancel button

is pressed for 3 seconds. When ice

cancel is selected, no water will be sent

to the ice box. Despite this, some ice

may be leftover in the ice box which

may be taken from there. To restart ice

formation, ice cancel button has to be

pressed for 3 seconds.

La page charge ...

Blomberg KQD 1360E Manuel utilisateur

Ce manuel convient également à

Blomberg KQD 1360E Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents