GE PFIC1NFYBV Le manuel du propriétaire

GEAppliances.com

Refrigerators

Bottom Freezer

200D9366P007 49-60580 01-09 JR

Safety Instructions . . . . . . . . . . .2, 3

Operating Instructions

Additional Features . . . . . . . . . . . . . . . . .8

Automatic Icemaker . . . . . . . . . . . . . . .11

Care and Cleaning . . . . . . . . . . . . .12–13

Controls . . . . . . . . . . . . . . . . . . . . . . . . . .4–5

Crispers and Pans . . . . . . . . . . . . . . . . . . .9

Freezer . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Replacing the Light Bulbs . . . . . . . . . .14

Shelves and Bins . . . . . . . . . . . . . . . . . .7, 8

Water Filter . . . . . . . . . . . . . . . . . . . . . . . . .6

Installation Instructions

Installing the Anti-Tip

Floor Bracket . . . . . . . . . . . . . . . . . .18–19

Installing the Refrigerator . . . . . . .20–24

Installing the Water Line . . . . . . . .33–35

Preparing to Install

the Refrigerator . . . . . . . . . . . . . . . . . . . .17

Removing and Replacing the

Freezer Drawer . . . . . . . . . . . . . . . . .25, 26

Reversing the Door Swing

(Single Door Refrigerator

Models only) . . . . . . . . . . . . . . . . . . .27–29

Removing and Replacing

the Doors (Double Door

Refrigerator Models only) . . . . . . .30–32

Trim Kits and Decorator

Panels . . . . . . . . . . . . . . . . . . . . . . . . .15–16

Troubleshooting Tips . . . . . .36–40

Normal Operating Sounds . . . . . . . . . .36

Consumer Support

Consumer Support . . . . . . . .Back Cover

Performance Data Sheet . . . . . . . . . . .43

State of California Water

Treatment Device Certificate . . . . . . .44

Warranty for Canadian

Customers . . . . . . . . . . . . . . . . . . . . . . . . .42

Warranty for U.S. Customers . . . . . . .41

Réfrigérateurs

Congélateur inférieur

Refrigeradores

Congelador inferior

Write the model and serial

numbers here:

Model # ____________________

Serial #______________________

Find these numbers on a label

on the right side, near the top of the

refrigerator compartment.

Models 21 and 25

Manuel d’utilisation

et d’installation

Owner’s Manual and

Installation Instructions

Manual del propietario

y instalación

La section française commence à la page 45

La sección en español empieza en la página 89

IMPORTANT SAFETY INFORMATION.

READ ALL INSTRUCTIONS BEFORE USING.

WARNING!

Use this appliance only for its intended purpose as described in this Owner’s Manual.

SAFETY PRECAUTIONS

When using electrical appliances, basic safety precautions should be followed, including the following:

■

■ This refrigerator must be properly installed

and located in accordance with the Installation

Instructions before it is used.

■

■ Do not allow children to climb, stand or hang

on the shelves in the refrigerator. They could

damage the refrigerator and seriously injure

themselves.

■

■ Do not touch the cold surfaces in the freezer

compartment when hands are damp or wet.

Skin may stick to these extremely cold surfaces.

■

■ Do not store or use gasoline or other flammable

vapors and liquids in the vicinity of this or any other

appliance.

■

■ Keep fingers out of the “pinch point” areas;

clearances between the doors and between the

doors and cabinet are necessarily small. Be careful

closing doors when children are in the area.

■

■ In refrigerators with automatic icemakers, avoid

contact with the moving parts of the ejector

mechanism, or with the heating element that

releases the cubes. Do not place fingers or hands

on the automatic icemaking mechanism while the

refrigerator is plugged in.

■

■ Unplug the refrigerator before cleaning and making

repairs.

NOTE: We strongly recommend that any servicing

be performed by a qualified individual.

■

■ Setting either or both controls to 0 (off) does

not remove power to the light circuit.

■

■ Do not refreeze frozen foods which have

thawed completely.

PROPER DISPOSAL OF THE REFRIGERATOR

Child entrapment and suffocation are not problems of

the past. Junked or abandoned refrigerators are still

dangerous…even if they will sit for “just a few days.” If

you are getting rid of your old refrigerator, please

follow the instructions below to help prevent

accidents.

Before You Throw Away Your Old

Refrigerator or Freezer:

■ Take off the doors.

■ Leave the shelves in place so that children may not

easily climb inside.

Refrigerants

All refrigeration products contain refrigerants,

which under federal law must be removed prior to

product disposal. If you are getting rid of an old

refrigeration product, check with the company

handling the disposal about what to do.

USE OF EXTENSION CORDS

Because of potential safety hazards under certain conditions, we strongly recommend against

the use of an extension cord.

However, if you must use an extension cord, it is absolutely necessary that it be a UL-listed (in the United States)

or a CSA certified (in Canada), 3-wire grounding type appliance extension cord having a grounding type plug

and outlet and that the electrical rating of the cord be 15 amperes (minimum) and 120 volts.

DANGER! RISK OF CHILD ENTRAPMENT

Consumer Support Troubleshooting Tips

Operating Instructions

Safety Instructions

Installation

Instructions

2

3

Consumer Support

Troubleshooting Tips

Operating InstructionsSafety Instructions

Installation

Instructions

GEAppliances.com

WARNING!

HOW TO CONNECT ELECTRICITY

Do not, under any circumstances, cut or remove the third (ground) prong from the power cord.

For personal safety, this appliance must be properly grounded.

The power cord of this appliance is equipped

with a 3-prong (grounding) plug which mates

with a standard 3-prong (grounding) wall outlet to

minimize the possibility of electric shock hazard from

this appliance.

Have the wall outlet and circuit checked by a qualified

electrician to make sure the outlet is properly

grounded.

Where a standard 2-prong wall outlet is encountered,

it is your personal responsibility and obligation to

have it replaced with a properly grounded 3-prong

wall outlet.

The refrigerator should always be plugged into its

own individual electrical outlet which has a voltage

rating that matches the rating plate.

This provides the best performance and also prevents

overloading house wiring circuits which could cause a

fire hazard from overheated wires.

Never unplug your refrigerator by pulling on the

power cord. Always grip plug firmly and pull straight

out from the outlet.

Repair or replace immediately all power cords that

have become frayed or otherwise damaged. Do not

use a cord that shows cracks or abrasion damage

along its length or at either end.

When moving the refrigerator away from the

wall, be careful not to roll over or damage the

power cord.

READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.

SAVE THESE INSTRUCTIONS

4

The temperature controls are preset in the factory at 37°F for the refrigerator

compartment and 0°F for the freezer compartment. Allow 24 hours for the temperature

to stabilize to the preset recommended settings.

The temperature controls can display both the SET temperature as well as the actual

temperature in the refrigerator and freezer. The actual temperature may vary slightly

from the SET temperature based on usage and operating environment.

Setting either or both controls to OFF stops cooling in both the freezer and refrigerator

compartments, but does not shut off electrical power to the refrigerator.

For Controls-on-the-Door Models:

To change the temperature, press and release the

WARMER or COLDER pad. The ACTUAL TEMP light will

come on and the display will show the actual

temperature. To change the temperature, tap either

the WARMER or COLDER pad until the desired

temperature is displayed.

For Controls Inside the Refrigerator:

Opening the door displays the actual temperature. To

change the temperature, press either the WARMER or

COLDER touch pads until the desired temperature is

displayed.

Once the desired temperature has been set,

the temperature display will return to the actual

refrigerator and freezer temperatures after 5 seconds.

Several adjustments may be required.

Each time you adjust controls, allow 24 hours for the

refrigerator to reach the temperature you have set.

To turn the cooling system off, tap the WARMER pad

for either the refrigerator or the freezer until the

display shows OFF. To turn the unit back on, press

the COLDER pad for either the refrigerator or freezer.

Then press the COLDER pad again and it will go to

the preset points of 0°F for the freezer and 37°F for

the refrigerator. Setting either or both controls to OFF

stops cooling in both the freezer and refrigerator

compartments, but does not shut off electrical power

to the refrigerator.

Changing the Temperature

NOTE: The refrigerator is shipped with protective film covering the temperature controls.

If this film was not removed during installation, remove it now.

Consumer Support Troubleshooting Tips

Operating Instructions

Safety Instructions

Installation

Instructions

(on some models)

Consumer Support

Troubleshooting Tips

Operating Instructions

Safety Instructions

Installation

Instructions

5

About TurboCool.

™

(on some models) GEAppliances.com

How it Works

TurboCool rapidly cools the refrigerator

compartment in order to more quickly

cool foods. Use TurboCool when adding a

large amount of food to the refrigerator

c

ompartment, putting away foods after they

have been sitting out at room temperature or

when putting away warm leftovers. It can

also be used if the refrigerator has been

without power for an extended period.

Once activated, the compressor will turn on

immediately and the fans will cycle on and

off at high speed as needed for eight hours.

The compressor will continue to run until the

refrigerator compartment cools to

approximately 34°F (1°C), then it will cycle on

and off to maintain this setting. After 8 hours,

or if TurboCool is pressed again, the

refrigerator compartment will return to

the original setting.

How to Use

Press TurboCool. The refrigerator

temperature display will show .

After TurboCool is complete, the

refrigerator compartment will return

to the original setting.

NOTES: The refrigerator temperature cannot

be changed during TurboCool.

The freezer temperature is not

affected during TurboCool.

When opening the refrigerator door

during TurboCool, the fans

will continue to run if they have

cycled on.

About Door Alarm (on some models)

The door alarm will sound if any door is open

for more than 2 minutes. The beeping stops

when you close the door.

(on some models)

About Energy Saver (on some models)

This product is equipped with an Energy

Saver feature. The refrigerator is shipped with

the Energy Saver feature enabled.

Over time, moisture can form on the front

surface of the refrigerator cabinet and cause

rust. If moisture does appear on the front

surface of the refrigerator cabinet, turn off

the Energy Saver feature by pressing and

releasing the ENERGY SAVER pad on the

control panel.

(on some models)

Water Filter Cartridge

The water filter cartridge is located in the

back upper right corner of the refrigerator

c

ompartment.

When to Replace the Filter

There is a replacement indicator light for the

water filter cartridge on the temperature

display. This light will turn orange to tell you

that you need to replace the filter soon. The

filter cartridge should be replaced when the

replacement indicator light turns red or if the

flow of water to the dispenser or icemaker

decreases.

Installing the Filter Cartridge

If you are replacing the cartridge, first

remove the old one by slowly turning it

to the left. DONOT pull down on the

cartridge. A small amount of water may

drip down.

CAUTION: If air has been

trapped in the system, the filter cartridge may

be ejected as it is removed. Use caution when

removing.

Remove the protective foil from the end

of the cartridge.

Fill the replacement cartridge with water

from the tap to allow for better flow from

the dispenser immediately after

installation.

Lining up the arrow on the cartridge and

the cartridge holder, slowly rotate the

cartridge clockwise until it stops. When

the cartridge is properly installed, you will

feel it “click” as it locks into place. Do not

overtighten.

Run water from the dispenser for

3 minutes (about 1

1

⁄2 gallons) to clear

the system and prevent sputtering.

See To Use the Dispenser section.

Press and hold the RESET WATER FILTER

pad for 3 seconds.

NOTE: A newly-installed water filter cartridge

may cause water to spurt from the

dispenser.

Filter Bypass Plug

You must use the filter bypass plug when a

replacement filter cartridge is not available.

T

he icemaker will not operate without the

filter or filter bypass plug.

Replacement Filters:

To order additional filter cartridges

in the United States, visit our Website,

GEAppliances.com, or call GE Parts and

Accessories, 800.626.2002.

Filter Model MWF

Customers in Canada should consult the

yellow pages for the nearest Mabe Service

Center.

About the water filter. (on some models)

Consumer Support Troubleshooting Tips

Operating Instructions

Safety Instructions

Installation

Instructions

6

(on some models)

Cartridge

Holder

Cartridge

Holder

7

Consumer Support

Troubleshooting Tips

Operating InstructionsSafety Instructions

Installation

Instructions

Rearranging the Shelves

To remove:

Remove all items from the shelf.

Tilt the shelf up at the front.

Lift the shelf up at the back and

bring the shelf out.

To replace:

While tilting the shelf up, insert the top

hook at the back of the shelf in a slot on

the track.

Lower the front of the shelf until the

bottom of the shelf locks into place.

Spillproof Shelves (on some models)

Spillproof shelves have special edges to

help prevent spills from dripping to lower

shelves. To remove or replace the shelves, see

Rearranging the Shelves.

About the shelves and bins. GEAppliances.com

Not all features are on all models.

Some models have wire shelves

that can be adjusted in the same

manner.

Shelves in the refrigerator compartment are adjustable.

Refrigerator Compartment

Slide-Out Spillproof Shelf (on some models)

The slide-out spillproof shelf allows you

to reach items stored behind others. The

special edges are designed to help prevent

spills from dripping to lower shelves.

To remove:

Remove all items from shelf.

Slide the shelf out until it stops.

Lift the front edge of the shelf until the

central tabs are above the front bar.

Continue pulling the shelf forward until it

can be removed.

To replace:

Place the rear shelf tabs just in front of

the central notches on the shelf frame.

Slide the shelf in until the central tabs are

slightly behind the front bar.

Lower the shelf into place until it is

horizontal and slide the shelf in.

Make sure that the shelf sits flat after

reinstallation and doesn’t move freely from

side to side.

Make sure you push the shelves all the way in

before you close the door.

Non-Adjustable Bins on the Door

To remove: Lift the bin straight up, then

pull out.

To replace: Engage the bin in the molded

supports on the door and push down.

It will lock in place.

Adjustable Bins on the Door

A

djustable bins can easily be carried from

refrigerator to work area.

To remove: Lift bin straight up, then

pull out.

To replace or relocate: Slide in the bin just

above the molded door supports, and push

down. The bin will lock in place.

T

he snugger helps prevent tipping, spilling

or sliding of small items stored on the door

shelf. Grip the finger hold near the rear of the

snugger and move it to fit your needs.

About the additional features.

Not all features are on all models.

Non-Adjustable Beverage Rack

To remove: Lift the rack straight up, then

pull out.

To replace: Engage the rack in the molded

supports on the door and push down. It will

lock in place.

About the shelves and bins.

Consumer Support Troubleshooting Tips

Operating Instructions

Safety Instructions

Installation

Instructions

8

9

Consumer Support

Troubleshooting Tips

Operating Instructions

Safety Instructions

Installation

Instructions

About the crispers and pans. GEAppliances.com

N

ot all features are on all models.

Fruit and Vegetable Crisper

Excess water that may accumulate in the

bottom of the drawers or under the drawers

should be wiped dry.

Adjustable Humidity Crisper (

on some models)

Slide the control all the way to the

HIGH setting to provide high humidity

recommended for most vegetables.

Slide the control all the way to the LOW

setting to provide lower humidity levels

recommended for most fruits.

Adjustable Temperature Deli Pan (on some models)

Slide the control all the way to the left for the

coldest temperature.

To remove:

Remove the fruit and vegetable drawers.

Pull the drawer out to the stop position.

Lift the lid to access the 4 swing locks.

Rotate all four swing locks to the unlock

position.

Lift the front of the drawer up and out.

To replace:

Make sure all four swing locks are in the

unlock position.

Place the sides of the drawer into the

drawer supports, making sure the swing

locks fit on the drawer slots.

Lock all four swing locks by rotating them

to the lock position.

Lower the lid and slide in the drawer.

Replace the fruit and vegetable drawers.

How to Remove and Replace the Deli Pan

Swing Locks

10

Freezer Shelves and Baskets

A shelf above the ice storage bin

A half-width basket

A shallow full-width basket

A deep full-width basket

Basket Removal

To remove the shallow full-width basket:

Pull the basket out to the stop location.

Lift the front up and over the stop

location.

Lift the basket up and out.

To remove the deep full-width basket on

freezer drawer models:

Open the freezer drawer until it stops.

The freezer basket rests on the inside

tabs on the drawer slides.

Lift the basket so that all 4 tabs are out of

the slide bracket.

Tilt the basket and lift out of the drawer.

Make sure the plastic sleeves remain

attached to the 4 tabs on the slide

brackets.

When replacing the deep full-width basket:

Tilt the basket back and lower it down

into the drawer. Rotate the basket to a

horizontal position and press it down into the

4 alignment tabs.

NOTE: Always be sure that all 4 basket tabs

are engaged in the slide brackets before

sliding back into the freezer.

To remove the half-width basket:

Pull the basket out to the stop location.

Lift the basket up at the front to release it

from the slides.

Lift the back up and out of the slide.

When replacing the basket, make sure that

the wire tabs and wire hooks on the sides

of the basket go into the slots in the top

of the upper basket slides.

NOTE: Always be sure to fully close this

basket.

About the freezer.

Not all features are on all models.

Appearance and features may vary

Appearance may vary

Tab

Consumer Support Troubleshooting Tips

Operating Instructions

Safety Instructions

Installation

Instructions

Consumer Support

Troubleshooting Tips

Operating Instructions

Safety Instructions

Installation

Instructions

About the automatic icemaker. GEAppliances.com

Automatic Icemaker (on some models)

The icemaker will produce seven cubes

p

er cycle—approximately 100–130 cubes

in a 24-hour period, depending on freezer

compartment temperature, room

temperature, number of door openings

and other use conditions.

See below for how to access ice and reach

the power switch.

If the refrigerator is operated before the

water connection is made to the icemaker,

set the power switch in the O (off) position.

When the refrigerator has been connected to

the water supply, set the power switch to the

l (on) position. The icemaker power light will

turn green when the freezer light switch is

pressed in or when the freezer door is closed.

The icemaker will fill with water when it cools

to 15°F (–10°C). A newly installed refrigerator

may take 12 to 24 hours to begin making ice

cubes.

You will hear a buzzing sound each time

t

he icemaker fills with water.

Throw away the first few batches of ice to

allow the water line to clear.

Be sure nothing interferes with the sweep

of the feeler arm.

When the bin fills to the level of the feeler

arm, the icemaker will stop producing ice.

It is normal for several cubes to be joined

together.

If ice is not used frequently, old ice cubes will

become cloudy, taste stale and shrink.

NOTE: In homes with lower-than-average

water pressure, you may hear the icemaker

cycle multiple times when making one batch

of ice.

NOTE: Set the power switch to the O (off)

position if the water supply is shut off.

A newly installed refrigerator may take 12 to 24 hours to begin making ice.

Icemaker

Feeler Arm

Power

Switch

Green

Accessing Ice and Reaching

the Power Switch

To reach the icemaker power switch, pull

the shelf above the ice bin straight out.

Always be sure to replace the shelf.

To access ice, simply pull the bin forward.

To access ice.

Shelf

Ice Bin

To reach the power switch.

Shelf

Ice Bin

Icemaker Accessory Kit

If your refrigerator did not come already

equipped with an automatic icemaker,

an icemaker accessory kit is available at

extra cost.

Check the back of the refrigerator for the

specific icemaker kit needed for your model.

To Use the Dispenser

Press the glass gently against the top of the

dispenser cradle.

The spill shelf is not self-draining. To reduce

water spotting, the shelf should be cleaned

regularly.

If no water is dispensed when the refrigerator

is first installed, there may be air in the water

line system. Press the dispenser arm for at

least two minutes to remove trapped air from

the water line and to fill the water system. To

flush out impurities in the water line, throw

away the first six glassfuls of water.

Locking the Dispenser

Press the LOCK pad for 3 seconds to lock

the dispenser and control panel. To unlock,

press and hold the pad again for 3 seconds.

Door Alarm

To set the alarm, press the DOOR ALARM

pad. The indicator light will illuminate.

This alarm will sound if either door is

open for more than 2 minutes. The beeping

stops when you close the door.

Spill Shelf

11

Dispenser Cradle

Care and cleaning of the refrigerator.

Cleaning the Outside

The door handles and trim. Clean with a

cloth dampened with soapy water. Dry with

a soft cloth. Do not use wax on the door

handles and trim.

Keep the outside clean. Wipe with a clean

c

loth lightly dampened with kitchen

appliance wax or mild liquid dish detergent.

Dry and polish with a clean, soft cloth.

Do not wipe the refrigerator with a soiled

dish cloth or wet towel. These may leave a

residue that can erode the paint. Do not

use scouring pads, powdered cleaners,

bleach or cleaners containing bleach

because these products can scratch and

weaken the paint finish.

The stainless steel panels and door

handles.

Stainless steel (on some models) can be

cleaned with a commercially available

s

tainless steel cleaner. A spray-on stainless

steel cleaner works best.

Do not use appliance wax or polish on the

stainless steel.

Silver-plated plastic parts. Wash parts with

soap or other mild detergents. Wipe clean

with a sponge, damp cloth or paper towel.

Do not scrub with steel-wool pads or other

abrasive cleaners.

Cleaning the Inside

To help prevent odors, leave an open box of

baking soda in the refrigerator and freezer

compartments.

Unplug the refrigerator before cleaning. If

this is not practical, wring excess moisture

out of sponge or cloth when cleaning around

switches, lights or controls.

Use an appliance wax polish on the inside

surface between the doors.

Use warm water and baking soda solution—

about a tablespoon (15 ml) of baking soda to

a quart (1 liter) of water. This both cleans and

neutralizes odors. Rinse and wipe dry.

After cleaning the door gaskets, apply a thin

layer of petroleum jelly to the door gaskets at

the hinge side. This helps keep the gaskets

from sticking and bending out of shape.

Avoid cleaning cold glass shelves with hot

water because the extreme temperature

difference may cause them to break.

Handle glass shelves carefully. Bumping

tempered glass can cause it to shatter.

Do not wash any plastic refrigerator parts

in the dishwasher.

Silver-accented plastic parts. Wash parts

with soapy water. Wipe clean with a sponge,

damp cloth or paper towel.

Do not scrub with steel-wool pads or other

abrasive cleaners.

12

Consumer Support Troubleshooting Tips

Operating Instructions

Safety Instructions

Installation

Instructions

Consumer Support

Troubleshooting Tips

Operating Instructions

Safety Instructions

Installation

Instructions

13

For long vacations or absences, remove food

and unplug the refrigerator. Clean the interior

with a baking soda solution of one

tablespoon (15 ml) of baking soda to one

quart (1 liter) of water. Leave the doors open.

Set the icemaker power switch to the O (off)

position and shut off the water supply to

the refrigerator.

If the temperature can drop below freezing,

have a qualified servicer drain the water

supply system (on some models) to prevent

serious property damage due to flooding.

GEAppliances.com

Behind the Refrigerator

Be careful when moving the refrigerator

away from the wall. All types of floor

coverings can be damaged, particularly

cushioned coverings and those with

e

mbossed surfaces.

R

aise the leveling legs located at the bottom

front of the refrigerator.

Pull the refrigerator straight out and return it

to position by pushing it straight in. Moving

the refrigerator in a side direction may result

in damage to the floor covering or

refrigerator.

Lower the leveling legs until they touch

the floor.

When pushing the refrigerator back, make

sure you don’t roll over the power cord or

icemaker supply line (on some models) and

e

nsure the anti-tip bracket is engaged (if

equipped).

Preparing for Vacation

Preparing to Move

Secure all loose items such as base grille,

shelves and drawers by taping them

securely in place to prevent damage.

When using a hand truck to move the

refrigerator, do not rest the front or back

of the refrigerator against the hand truck.

This could damage the refrigerator. Handle

only from the sides of the refrigerator.

Be sure the refrigerator stays in an upright

position during moving.

14

Consumer Support Troubleshooting Tips

Operating Instructions

Safety Instructions

Installation

Instructions

Refrigerator Lights

CAUTION: L

ight bulbs may

be hot.

Unplug the refrigerator.

To remove the light shield, grasp the

shield at the back and pull out to release

the tabs at the back.

Rotate the shield down and then forward

to release the tabs at the front of the

shield.

A

fter replacing with an appliance bulb

of the same or lower wattage, replace

the shield.

Plug the refrigerator back in.

NOTE: Appliance bulbs may be ordered from

GE Parts and Accessories, 800.626.2002.

Freezer Light

Replacing the light bulbs.

Turning the control to the 0 (off) position does not remove power to the light circuit.

Appearance may vary

CAUTION: Light bulbs may

be hot.

Unplug the refrigerator.

Remove the freezer basket for access.

The bulb is located at the rear of the

freezer inside a light shield.

To remove, grasp the shield at the top

and pull out to release the tabs at the

bottom.

After replacing with an appliance bulb

of the same or lower wattage, replace

the shield and freezer basket.

Plug the refrigerator back in.

Light

Shield

15

Consumer Support

Troubleshooting Tips

Operating Instructions

Safety Instructions

Installation

Instructions

Trim kits and decorator panels.

Read these instructions completely and carefully.

Before You Begin

Some models are equipped with trim kits that allow you to install door panels. You can order

pre-cut black or white decorator panels from GE Parts and Accessories, 800.626.2002, or you

can add wood panels to match your kitchen cabinets.

Panels less than 1/4″ (6 mm) thick

When installing wood panels less than 1/4″ (6 mm) thick, you need to create a filler panel, such as 1/8″

cardboard, that will fit between the face of the door and the wood panel. If you are installing the pre-cut

decorator panels, pre-cut filler panels are included in the kit. The combined thickness of the decorator or

wood panel and the filler panel should be 11/32″ (8.7 mm) with the panel itself being no larger than 1/4″ (6 mm).

For panel required models

Panels 1/4″ thick or less

1/4″ max

The handle and the top and bottom trim stand in front of the surface of the door, which requires that the filler

be smaller in length and width than the panel. Use the guidelines below and tape the filler onto the back of the

panel.

Left Fresh Food Door

Freezer Door

Filler

2 1/2″ (63.5 mm)

3/4″ (19 mm)

Panel

Filler

2 1/2″ (63.5 mm)

3/4″ (19 mm)

Panel

Right Fresh Food Door

Filler

2 1/2″ (63.5 mm)

3/4″ (19 mm)

Panel

Consumer Support Troubleshooting Tips

Operating Instructions

Safety Instructions

Installation

Instructions

16

Trim kits and decorator panels.

Dimensions for Custom Wood Panels

3/4″ (19 mm) or Raised Panel

A raised panel design screwed or glued to a 1/4″ (6 mm) thick backing, or a 3/4″ (19 mm) routed board can be

used. The raised portion of the panel must be fabricated to permit clearances of at least 2″ (5.1 cm) from the

handle side for fingertip clearance.

Panels thicker than 1/4″ (6 mm), up to 3/4″ (19 mm) max., will require that the outer 5/16″ (8 mm) of panel

perimeter be no thicker than 1/4″ (6 mm).

Weight limitations for custom panels:

Fresh Food 10 lbs. (4.5 kg) max. for each door

Freezer Door 18 lbs. (8 kg) max.

2″ (5.1 cm)

Clearance

Handle Side

Appearance

Panel

Refrigerator

Door

1/4″ (6 mm)

Thick Backing

3/4″

Panels thicker than 1/4″ (6 mm)

1/4″ (6 mm) max

3/4″ (19 mm)

5/16″ (8 mm)

Right Fresh Food Door

Freezer Door

Top, right and

bottom

16 29/32″ (42.9 cm)

5/16″ (8 mm)

minimum at

1/4″ (6 mm)

thickness

Raised portion

of panel

2″ (51 mm)

minimum at

1/4″ (6 mm)

thickness

Handle side

26 3/32″

(66.3 cm)

2″ (51 mm) minimum at

1/4″ (6 mm) thickness

Handle side

Left, right and

bottom sides

5/16″ (8 mm) minimum

at 1/4″ (6 mm) thickness

35 29/32″ (91.2 cm)

Raised

portion

of panel

38 15/16″

(98.9 cm)

Left Fresh Food Door

Top, left and

bottom

16 29/32″ (42.9 cm)

5/16″ (8 mm)

minimum at

1/4″ (6 mm)

thickness

Raised portion

of panel

2″ (51 mm)

minimum at

1/4″ (6 mm)

thickness

Handle side

38 15/16″

(98.9 cm)

1/8″

(3 mm)

1/8″

(3 mm)

1/8″

(3 mm)

1/8″

(3 mm)

1/8″

(3 mm)

1/4″

(6 mm)

1/4″

(6 mm)

1/4″

(6 mm)

1/4″

(6 mm)

1/4″

(6 mm)

1/8″

(3 mm)

1/4″

(6 mm)

Installation

Refrigerator

Instructions

Models 21 and 25

Questions? Call 800.GE.CARES (800.432.2737) or visit our Website at: GEAppliances.com

In Canada, call 1.800.561.3344 or visit our Website at: www.GEAppliances.ca

BEFORE YOU BEGIN

Read these instructions completely and carefully.

•

IMPORTANT — Save these instructions for local

inspector’s use.

•

IMPORTANT — Observe all governing codes and

ordinances.

• Note to Installer – Be sure to leave these instructions with

the Consumer.

• Note to Consumer – Keep these instructions for future

reference.

• Skill level – Installation of this appliance requires basic

mechanical skills.

• Completion time – Refrigerator Installation

20 minutes

Water Line Installation

30 minutes

Anti-Tip Bracket Installation

20 minutes

• Proper installation is the responsibility of the installer.

• Product failure due to improper installation is not covered

under the Warranty.

PREPARATION

MOVING THE REFRIGERATOR INDOORS

If the refrigerator will not fit through a doorway, the

refrigerator door and freezer drawer can be removed.

• To remove the refrigerator door, see Step 1 in the

Reversing the Door Swing section.

• To remove the freezer drawer, see the Removing the

Freezer Drawer section.

WATER SUPPLY TO THE ICEMAKER AND DISPENSER

(ON SOME MODELS)

If the refrigerator has an icemaker, it will have to be

connected to a cold water line. A GEwater supply kit

(containing tubing, shut-off valve, fittings and instructions)

is available at extra cost from your dealer, by visiting

our Website at GEAppliances.com (in Canada at

www.GEAppliances.ca) or from Parts and Accessories,

800.626.2002 (In Canada 1.888.261.3055).

TOOLS YOU MAY NEED

Adjustable Wrench

1/4″ Outer Diameter

Compression Nut

and Ferrule (sleeve) (icemaker

models only)

Phillips-Head Screwdriver

17

3/8″ and 5/16″ Socket

Ratchet/Driver

3/32″, 1/8″ and 1/4″ Allen

wrenches

MATERIALS YOU MAY NEED (not included)

Pencil

1/8″ Drill Bit and

Electric or Hand Drill

Tape measure

1/4″ Nut Driver

Lag Bolts

Anchor Sleeves

For Anti-Tip Bracket Mounted on CONCRETE Floors Only

Drill Bit Appropriate for Anchors

Wire Cutters

Level

LOCATING THE ANTI-TIP

FLOOR BRACKET

Place the anti-tip floor bracket locator template

(included inside the anti-tip kit) onto the floor

up against the rear wall, within W, and in line

with the desired location of the RH side of the

refrigerator (see Figure 1).

Place the anti-tip floor bracket onto the locator

template with its RH floor holes lined up with

the floor holes indicated on the template sheet,

approximately 7

1

⁄4″ from the edge of the sheet

or the RH side of the refrigerator.

Hold down in position and use the anti-tip floor

bracket as a template for marking the holes

based upon your configuration and type of

construction as shown in Step 3. Mark the hole

locations with a pencil, nail or awl.

NOTE:

• It is REQUIRED to use at least 2 screws to

mount the floor bracket (one on each side of

the anti-tip floor bracket). Both must be into

either the wall or the floor. Figure 2 indicates

all the acceptable mounting configurations

for screws. Identify the screw holes on the

anti-tip floor bracket for your configuration.

MEASURE CABINET OPENING

AVAILABLE VS. REFRIGERATOR WIDTH

Measure width of cabinet opening where

refrigerator will be placed, W.

Be sure to account for any countertop

overhang, baseboard thickness and any

clearance desired. Width, W, should not be less

than 36 inches. The refrigerator will be placed

approximately in the middle of this opening.

WARNING

Under certain circumstances, this refrigerator

can tip forward.

Injury to persons can result.

Install Anti-Tip Bracket packed with this

refrigerator.

1

Baseboard

Thickness

or Countertop

Overhang

(Whichever

Is Greater) Plus

Any Desired

Clearance

Rear Wall

Front

RH Side

2

A

B

C

W

Base

Bracket

on the

Refrigerator

2 Wall Holes

RH Side of

Floor – Concrete

(2 Holes)

Floor – Wood

(2 Holes)

7

1

⁄4″

Locator Template

Floor Bracket

to Install

RH Holes

Rear RH Corner

of Cabinet Wall

REFRIGERATOR

Figure 1 – Installation Overview

18

Installation Instructions

INSTALLING THE ANTI-TIP FLOOR BRACKET (on 21 ft. models)

Installation Instructions

LOCATING THE ANTI-TIP

FLOOR BRACKET (cont.)

2

Preferred Installation –

Wood

Preferred Installation –

Concrete

Minimum Acceptable #1 –

Wall Plate Stud

Minimum Acceptable #2 –

Wood Floor

Minimum Acceptable #3 –

Concrete Floor

Figure 2 – Acceptable Screw Placement

Locations

CONCRETE Wall and Floor Construction:

• Anchors required (not provided):

4 each 1/4” x 1 1/2” lag bolts

4 each 1/2” O.D. sleeve anchors

• Drill the recommended size holes for the

anchors into the concrete at the center of the

holes marked in Step 2.

• Install the sleeve anchors into the drilled

holes. Place the anti-tip floor bracket as

indicated in Step 2. Remove the locator

template from the floor.

• Install the lag bolts through the anti-tip floor

bracket and tighten appropriately.

WOOD Wall and TILE Floor Construction:

• For this special case, locate the 2 wall holes

identified in Fig. 1. Drill an angled 1/8” pilot

hole (approx. as shown in Fig. 3) in the center

of each hole.

• Mount the anti-tip floor bracket using the

Minimum Acceptable Installation #1, as

illustrated in Fig. 2.

C

B

ANTI-TIP BRACKET INSTALLATION

WOOD Wall and Floor Construction:

• Drill the appropriate number of 1/8” pilot

holes in the center of each floor bracket hole

being used (a nail or awl may be used if a drill

is not available) AND remove the locator

template from the floor.

• Mount the anti-tip floor bracket by fastening

the 2, or preferably 4, #10-16 hex-head

screws tightly into place as illustrated in

Figure 3.

3

A

POSITIONING THE REFRIGERATOR

TO ENGAGE THE ANTI-TIP FLOOR

AND BASE BRACKETS

Before pushing the refrigerator into the

opening, plug the power cord into the

receptacle and connect waterline (if equipped).

Check for leaks.

Locate the refrigerator’s RH side and move

back approximately in line with the RH side of

the cabinet opening, W. This should position the

anti-tip floor bracket to engage the anti-tip

base bracket on the refrigerator.

Gently roll the refrigerator back into the

cabinet opening until it comes to a complete

stop. Check to see if the refrigerator front lines

up with the cabinet front face. If not, carefully

rock the refrigerator forward and backward

until engagement occurs and you notice that

the refrigerator is fully pushed up against the

rear wall.

OPTIONAL: Adjust the rear (and front) wheel

height settings to fully engage the rear anti-tip

brackets, while also aligning the refrigerator

front with the cabinet front face.

4

A

C

B

D

Figure 3 – Attachment to

Wall and Floor

NOTE:

If you pull the refrigerator out and away from the

wall for any reason, make sure the anti-tip floor

bracket is engaged when the refrigerator is pushed

back against the rear wall.

Rear RH Corner of

the Refrigerator

Floor

Wall

Plate

Stud

Floor

Bracket

2 Screws Must

Enter Wood or

Metal Stud

Wall

19

Installation Instructions

INSTALLING THE REFRIGERATOR

REFRIGERATOR LOCATION

• Do not install the refrigerator where the temperature will

go below 60°F (16°C) because it will not run often enough

to maintain proper temperatures.

• Do not install the refrigerator where the temperature will

go above 100°F (37°C) because it will not perform properly.

• Install it on a floor strong enough to support it fully loaded.

CLEARANCES

Allow the following clearances for ease of installation, proper

air circulation and plumbing and electrical connections.

Standard Depth Counter Depth

Models Models

Sides 1/8″ (3 mm) 1/8″ (3 mm)

Top 1″ (25 mm) 1″ (25 mm)

Back 1″ (25 mm) 1/2″ (13 mm)

CONNECTING THE REFRIGERATOR TO

THE HOUSE WATER LINE

(icemaker and dispenser models)

A cold water supply is required for automatic icemaker

operation. If there is not a cold water supply, you will

need to provide one. See Installing the Water Line

section.

NOTES:

• Before making the connection to the refrigerator, be

sure the refrigerator power cord is not plugged into

the wall outlet.

• If your refrigerator does not have a water filter, we

recommend installing one if your water supply has

sand or particles that could clog the screen of the

refrigerator’s water valve. Install it in the water line

near the refrigerator. If using GE SmartConnect

™

Refrigerator Tubing Kit, you will need an additional

tube (WX08X10002) to connect the filter. Do not cut

plastic tube to install filter.

1

REMOVE TOP CAP (on some models)

•IMPORTANT NOTE: This refrigerator is 34-1/2″ deep.

Doors and passageways leading to the installation

location must be at least 36″ wide in order to leave the

doors and handles attached to the refrigerator while

transporting it into the installation location. If

passageways are less than 36″, the refrigerator doors

and handles can easily be scratched and damaged.

The top cap and doors can be removed to allow the

refrigerator to be safely moved indoors. Start with Step A.

•If it is not necessary to remove doors, skip Step A. Leave

tape and all packaging on doors until the refrigerator is

in the final location.

•SKID REMOVAL: Tilt refrigerator to each side to remove

skid.

•NOTE: Use a padded hand truck to move this refrigerator.

Place the refrigerator on the hand truck with a side

against the truck. We strongly recommend that TWO

PEOPLE move and complete this installation.

Locate and remove the two Phillips head screws on the

top of the refrigerator. Remove the two screws on each

side at the rear of the top cap.

Lift off and remove top cap.

Remove the fresh-food door. Refer to Steps 1 through 3

of “Reversing the Door Swing” section.

Remove the bottom freezer drawer. Refer to “Removing

Freezer Drawer” section.

Move refrigerator to the installation location.

A

B

C

D

20

REMOVE TOP CAP (cont.) (on some models)

REINSTALL DOORS, DRAWERS AND TOP CAP

Carefully lower the door onto the center hinge. Reinstall

top hinge. NOTE: Ensure the door is properly aligned to

the case top to avoid readjustment of the door during

top cap reinstallation.

Place cap over the top of the refrigerator. Reinstall the

original screws in the top and back of the cap.

Reinstall the bottom freezer drawer. Refer to “Replacing

the Freezer Drawer” section.

E

F

G

A

Top Hinge B

La page charge ...

GE PFIC1NFYBV Le manuel du propriétaire

Ce manuel convient également à

GE PFIC1NFYBV Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents