Regency F2450 Le manuel du propriétaire

Marque: Regency

Modèle: F2450

Catégorie: Poêles

Taper: Le manuel du propriétaire

Ce manuel convient également à

Classic F2450

FPI FIREPLACE PRODUCTS INTERNATIONAL LTD. 6988 Venture St., Delta, BC Canada, V4G 1H4

920-036a

0219WS026S

MODEL: F2450M

Classic™ Freestanding Woodstove

F2450M

12.10.19

Installer: Please complete the details on the back cover

and leave this manual with the homeowner.

Homeowner: Please keep these instructions for future reference.

Owners &

Installation Manual

Tested by:

www.regency-ﬁre.com

French Manual Download:

Manuel en Français:

2 | F2450M Regency Freestanding Woodstove

Thank-you for purchasing a

REGENCY FIREPLACE PRODUCT.

The pride of workmanship that goes into each of our products will give you years of trouble-free enjoyment. Should you have any questions about

your product that are not covered in this manual, please contact the REGENCY DEALER in your area.

"This wood heater has a manufacturer set minimum low burn rate that must not be altered. It is against federal regulations to alter this

setting or otherwise operate this wood heater in a manner inconsistent with operating instructions in this manual.” Failure to follow

the manual details can lead to smoke and CO emissions spilling into the home. It is recommended to have monitors in areas that are

expected to generate CO such as heater fueling areas.

"U.S. ENVIRONMENTAL PROTECTION AGENCY Certiﬁed to comply with 2020 particulate emission standards using cord wood.” Tested

to ASTM E3053. Model Regency F2450M – 2.3g /hr.

"This manual describes the installation and operation of the Regency F2450M wood heater. This heater meets the 2020 U.S. Environmental Protec-

tion Agency’s cord wood emission limits for wood heaters. Under speciﬁc test conditions this heater has been shown to deliver heat at rates rang-

ing from 14,200 BTU/hr to 53,600 BTU/hr.” Efﬁciency is determined using the B415 method resulting in lower and higher heat values. This heater

generates the best efﬁciency when operated using well-seasoned wood and installed in the main living areas where the majority of the chimney is

within the building envelope. "This wood heater needs periodic inspection and repair for proper operation.

It is against federal regulation to operate this wood heater in a manner inconsistent with operating instructions in this manual."

CAUTION: BURN UNTREATED WOOD ONLY. OTHER MATERIALS SUCH AS WOOD PRESERVATIVES, METAL FOILS, COAL, PLASTIC,GARBAGE,

SULPHUR OR OIL MAY DAMAGE THE STOVE.

"This heater is designed to burn natural wood only. Higher efﬁciencies and lower emissions generally result when burning air dried seasoned hard-

woods, as compared to softwoods or to green or freshly cut hardwoods."

DO NOT BURN:

• Treated wood

• Lawn clippings or yard waste • Manure or animal remains

• Coal

• Materials containing rubber including tires • Saltwater driftwood or other previously salt

water saturated materials

• Garbage

• Materials containing plastic • Unseasoned wood

• Cardboard

• Waste petroleum products , paints or paint thinners or asphalt

products

• Paper products, cardboard, plywood or par-

ticle board. The prohibition against burning

these materials does not prohibit the use

of ﬁre starters made from paper, cardboard,

saw dust, wax and similar substances for the

purpose of starting a ﬁre in a wood heater.

• Solvents

• Materials containing asbestos

• Colored Paper

• Construction or demolition debris

• Trash

• Railroad ties

Burning these materials may result in release of toxic fumes or render the heater ineffective and cause smoke.

The authority having jurisdiction (such as Municipal Building Department, Fire Department, Fire Prevention Bureau, etc.) should be con-

sulted before installation to determine the need to obtain a permit.

This unit must be connected to either a listed factory built chimney suitable for use with solid fuels and conforming to, ULC629 in Canada or UL-

103HT in the United States of America. or code approved masonry chimney with ﬂue liner.

F2450M is tested and certiﬁed to ULC-S627-00 and UL1482-2011 (R2015).

SAVE THESE INSTRUCTIONS

F2450M Regency Freestanding Woodstove | 3

table of contents

Safety Label for F2450M ................................................... 4

Dimensions

Unit Dimensions ................................................................ 5

Outside Air Dimensions ..................................................... 5

Installation

Modular installation options ............................................... 6

Stove Assembly Prior To Installation .................................. 7

Airmate Assembly for F2450M .......................................... 7

Rear Heat Deﬂector Assembly for F2450M ....................... 7

Side Shield Adjustment ..................................................... 7

Pedestal Assembly Installation .......................................... 8

Logo Installation ................................................................ 8

Bottom Heat Shield and Legs Installation .......................... 8

Room Air - Important ......................................................... 9

Minimum Clearance To Combustible Materials .................. 9

Minimum Alcove Clearance and Clearance

to Combustible Materials ................................................. 10

Floor Protection ............................................................... 10

Step By Step Chimney And Connector Installation ......... 12

Masonry Chimney............................................................ 13

Masonry Fireplace ........................................................... 13

Factory Built Chimney...................................................... 13

Combustible Wall Chimney Connector Pass-throughs .... 14

Mobile Home Installation ................................................. 15

Mobile Home Kit for Canada ........................................... 16

Installing Outside Air from Pedestal Base ....................... 17

Installing Outside Air Using Bottom Heat Shield/Legs ..... 17

Recommended Heights For Woodstove Flue .................. 18

Optional Outside Air Kit .................................................. 19

Brick Installation .............................................................. 20

Wood Handle & Door Assembly ...................................... 21

Flue Bafﬂe & Secondary Air Tube Installation .............22

Fan Installation ...........................................................23

Stainless Steel Smoke Deﬂector Installation ...............24

Seasoned Firewood .....................................................25

Operation

Operating Instructions .................................................25

Draft Control ................................................................25

First Fire ......................................................................26

Fan Operation ..............................................................27

Ash Disposal ................................................................27

Ash Drawer Operating Guidelines ...............................27

Safety Guidelines and Warnings .................................27

Maintenance

Classic Door Handle Replacement ..............................28

Glass Replacement .....................................................28

Maintenance ................................................................29

Creosote ......................................................................29

Ways to Prevent and Keep Unit Free of Creosote .......29

Door Gasket ................................................................29

Glass Maintenance ......................................................29

Wood Storage ..............................................................29

Secondary Air Tube Removal / Installation ..................30

Annual Maintenance ....................................................30

Vertical Stainless Deﬂector Replacement....................31

Parts

Main Assembly ............................................................32

Bases ...........................................................................34

Warranty

Warranty ......................................................................36

CAUTION: To avoid burns or wood splinters, when opening/closing the fuel

door or adding wood to the ﬁre, You should always wear appropriate protective

gloves to protect your hands from the heat being emitted from this ﬁreplace.

4 | F2450M Regency Freestanding Woodstove

safety decal

This is a copy of the label that accompanies each

Regency Freestanding Woodstove (F2450M).

We have printed a copy of the contents here

for your review.

NOTE: Regency units are constantly being

improved. Check the label on the unit and if

there is a difference, the label on the unit is the

correct one.

Part #: 920-037a

Size: 6.53" H x 10.8" W (File at 100%)

Color: black on grey except for the items indicated as being printed in red.

Mar. 16/17: Created decal

June 06/18: Updated decal

July16/18: Updated decal w/EPA info

July 19/18: Updated decal

Nov.22/18: Updated Floor protection dim.

Mar 06/19: Updated clearances + standards

Oct 07/19: Updated to mobile homes in Canada and the United States

duplicate serial number

MINIMUM ALCOVE CEILING HEIGHT: 2109 MM / 83" MAXIMUM ALCOVE DEPTH 1219 MM / 48".

MINIMUM CLEARANCES FOR HORIZONTAL CONNECTOR TO CEILING: 405 MM / 16"

THE SPACE BENEATH THE HEATER MUST NOT BE OBSTRUCTED. OPERATE ONLY WITH FIREBRICKS IN PLACE.

FOR USE WITH SOLID WOOD FUEL ONLY. USE OF OTHER FUELS MAY DAMAGE HEATER AND CREATE A HAZARDOUS CONDITION. DO NOT OBSTRUCT COMBUSTION AIR OPENINGS. OPERATE ONLY WITH

FIREBRICKS IN PLACE. RISK OF SMOKE AND FLAME SPILLAGE, OPERATE ONLY WITH DOORS FULLY CLOSED. IF INSTALLED IN A MOBILE HOME OPERATE ONLY WITH DOORS FULLY CLOSED - OPEN FEED DOOR

TO FEED FIRE ONLY. DO NOT USE GRATE OR ELEVATE FIRE. BUILD WOOD FIRE DIRECTLY ON HEARTH. DO NOT OVERFIRE - IF HEATER OR CHIMNEY CONNECTOR GLOWS YOU ARE OVERFIRING. INSPECT

AND CLEAN CHIMNEY AND CONNECTOR FREQUENTLY. UNDER CERTAIN CONDITIONS OF USE CREOSOTE BUILDUP MAY OCCUR RAPIDLY. KEEP FURNISHINGS AND OTHER COMBUSTIBLE MATERIAL AWAY

FROM HEATER. REPLACE GLASS ONLY WITH NEOCERAM GLASS. COMBUSTIBLE FLOOR MUST BE PROTECTED BY NON-COMBUSTIBLE MATERIAL EXTENDING BENEATH THE HEATER AND TO THE FRONT AND

SIDES AS INDICATED OR TO THE NEAREST PERMITTED COMBUSTIBLE MATERIAL.

OPTIONAL COMPONENT: FAN PART #075-917, ELECTRICAL RATING: VOLTS 115, 60 HZ, 2 AMPS

DANGER: RISK OF ELECTRIC SHOCK. DISCONNECT POWER BEFORE SERVICING UNIT. DO NOT ROUTE POWER CORD UNDER OR IN FRONT OF APPLIANCE.

COMPONENTS REQUIRED FOR MOBILE HOME INSTALLATION: OUTSIDE AIR KIT

IN CANADA: LISTED ULCS 629 CHIMNEY. USE CHIMNEY COMPONENTS AS SPECIFIED IN INSTALLATION/INSTRUCTIONS

IN USA: LISTED UL 103 HT CHIMNEY

HAUTEUR MINIMALE DU PLAFOND DE L’ALCÔVE : 2109 MM / 83 PO PROFONDEUR MAXIMALE DE L’ALCÔVE : 1219 MM / 48 PO

DÉGAGEMENT MINIMAL DU PLAFOND POUR UN CONNECTEUR HORIZONTAL : 405 MM / 16 PO.

L’ESPACE SOUS LE POÊLE NE DOIT PAS ÊTRE OBSTRUÉ. UTILISER SEULEMENT AVEC LES BRIQUES RÉFRACTAIRES EN PLACE.

À UTILISER AVEC DU BOIS SOLIDE SEULEMENT. L’UTILISATION D’AUTRES COMBUSTIBLES PEUT ENDOMMAGER LE POÊLE ET CRÉER UNE CONDITION DANGEREUSE. NE PAS OBSTRUER LES OUVERTURES

D’AIR DE COMBUSTION. UTILISER SEULEMENT AVEC LA PORTE FERMÉE – OUVRIR SEULEMENT LA PORTE DE CHARGEMENT POUR ALIMENTER LE FEU. NE PAS UTILISER DE GRILLE À BÛCHES NI SURÉLEVER

LE FEU. MONTER LE FEU DE BOIS DIRECTEMENT SUR L’ÂTRE. NE PAS SURCHAUFFER – SI LE POÊLE OU LE CONNECTEUR DE CHEMINÉE SE MET À ROUGIR, RISQUE DE SURCHAUFFAGE. INSPECTER

ET NETTOYER FRÉQUEMMENT LA CHEMINÉE ET LE CONNECTEUR. DANS CERTAINES CONDITIONS D’UTILISATION, UN DÉPÔT DE CRÉOSOTE PEUT SE FORMER RAPIDEMENT. GARDER LES MEUBLES ET

AUTRES MATÉRIAUX COMBUSTIBLES ÉLOIGNÉS DU POÊLE. REMPLACER LA VITRE SEULEMENT PAR DU VERRE EN NEOCERAM. LE PLANCHER COMBUSTIBLE DOIT ÊTRE PROTÉGÉ PAR DES MATÉRIAUX NON

COMBUSTIBLES DÉPASSANT SUR LE DESSOUS, LE DEVANT ET LES CÔTÉS DU POÊLE, TEL QU’INDIQUÉ, OU JUSQU’AU MATÉRIAU COMBUSTIBLE LE PLUS PRÈS PERMIS.

COMPOSANTS EN OPTION : VENTILATEUR PIÈCE N

075-917, ALIMENTATION ÉLECTRIQUE : 115 VOLTS, 60 HZ, 2 AMP.

DANGER : RISQUE D’ÉLECTROCUTION. DÉCONNECTER L’ALIMENTATION ÉLECTRIQUE AVANT D'EFFECTUER L’ENTRETIEN DU POÊLE. NE PAS INSTALLER LE CORDON ÉLECTRIQUE SOUS OU DEVANT L’APPAREIL.

COMPOSANTS EXIGÉS POUR INSTALLATION DANS UNE MAISON MOBILE : KIT DE PRISE D’AIR EXTÉRIEUR.

AU CANADA : CHEMINÉE HOMOLOGUÉE ULCS 629. UTILISER LES PIÈCES DE LA CHEMINÉE TEL QUE SPÉCIFIÉ DANS LES CONSIGNES D’INSTALLATION.

AUX ÉTATS-UNIS : CHEMINÉE HOMOLOGUÉE UL103HT.

512

CAUTION

HOT WHILE IN OPERATION DO NOT TOUCH. KEEP CHILDREN,

CLOTHING AND FURNITURE AWAY. CONTACT MAY CAUSE

SKIN BURNS. READ NAMEPLATE AND INSTRUCTIONS.

ATTENTION

CHAUD DURANT LE FONCTIONNEMENT. NE TOUCHEZ PAS.

ÉLOIGNEZ LES ENFANTS, LES VÊTEMENTS ET LES MEUBLES.

LE CONTACT PEUT CAUSER DES BRÛLURES.

LISEZ LA PLAQUE SIGNALÉTIQUE ET LES INSTRUCTIONS

MADE IN CANADA / FABRIQUÉ AU CANADA

MANUFACTURED BY/ FABRIQUÉ PAR :

FPI FIREPLACE PRODUCTS INTERNATIONAL LTD.

6988 VENTURE ST.

DELTA, BC V4G 1H4

LISTED SPACE HEATER, SOLID FUEL TYPE, ALSO

SUITABLE FOR MOBILE HOME INSTALLATION /

APPAREIL DE CHAUFFAGE AMBIANT HOMOLOGUÉ

À COMBUSTIBLE SOLIDE, CONVENANT AUSSI

POUR INSTALLATION DANS UNE MAISON MOBILE

FLOOR PROTECTION*

PROTECTION DE PLANCHER*

Au Canada, la protection de plancher doit dépasser de 18 po (457 mm)

à l’avant (16 po aux États-Unis) et de 8 po (200 mm) de chaque côté du

poêle et derrière le poêle.

* In Canada, ﬂoor protection must extend 18" (457mm) to the front (16"

for USA) and 8" (203mm) to each side and back of the stove.

DO NOT REMOVE THIS LABEL/

NE RETIREZ PAS CETTE ÉTIQUETTE

512

INSTALL AND USE ONLY IN ACCORDANCE WITH THE MANUFACTURER'S INSTALLATION AND OPERATING INSTRUCTIONS. CONTACT LOCAL BUILDING OR FIRE OFFICIALS ABOUT RESTRICTIONS

AND INSTALLATION INSPECTION IN YOUR AREA. USE 150 MM (6 IN.) DIAMETER MINIMUM 24 MSG BLACK OR 26 MSG BLUED STEEL CONNECTOR WITH LISTED UL103 HT FACTORY-BUILT

CHIMNEY SUITABLE FOR USE WITH SOLID FUELS OR MASONRY CHIMNEY.

SEE LOCAL BUILDING CODE AND MANUFACTURER'S INSTRUCTIONS FOR PRECAUTIONS REQUIRED FOR PASSING A CHIMNEY THROUGH A COMBUSTIBLE WALL OR CEILING. DO NOT PASS

CHIMNEY CONNECTOR THROUGH COMBUSTIBLE WALL OR CEILING. DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE SERVING ANOTHER APPLIANCE.

INSTALLER ET UTILISER SEULEMENT SELON LES CONSIGNES D’INSTALLATION ET D’UTILISATION DU FABRICANT. CONTACTER LES RESPONSABLES DU BÂTIMENT OU DU SERVICE-

INCENDIE DE VOTRE RÉGION POUR CONNAÎTRE LES RESTRICTIONS ET EXIGENCES D’INSPECTION DANS VOTRE RÉGION. UTILISER UN CONNECTEUR D’UN DIAMÈTRE MINIMAL DE 150

MM (6 PO) 24 MSG EN ACIER NOIR OU 26 MSG EN ACIER BRONZÉ AVEC CHEMINÉE PRÉFA-BRIQUÉE HOMOLOGUÉE UL103 HT CONÇUE POUR ÊTRE UTILISÉE AVEC DES COMBUSTIBLES

SOLIDES OU UNE CHEMINÉE EN MAÇONNERIE.

VOIR LE CODE DU BÂTIMENT LOCAL ET LES INSTRUCTIONS DU FABRICANT CONCERNANT LES PRÉCAUTIONS D'INSTALLATION D'UNE CHEMINÉE TRAVERSANT UN MUR OU UN PLAFOND

EN MATÉRIAUX COMBUSTIBLES. NE PAS FAIRE TRAVERSER LE CONNECTEUR DE CHEMINÉE DANS UN MUR OU PLAFOND EN MATÉRIAUX COMBUSTIBLES. NE PAS RACCORDER CE POÊLE

À BOIS À UN CONDUIT DE CHEMINÉE DESSERVANT UN AUTRE APPAREIL.

920-037a

MODEL: REGENCY MEDIUM FREESTANDING STOVE - F2450M

TESTED TO: ULC S627-00 / UL 1482-2011 (R2015)

A 1245 mm / 49 in (Canada)

A 1194mm / 47 in (USA)

B 457 mm / 18 in

B 406 mm / 16 in

C 856 mm / 33-11/16 in

D 203 mm / 8 in

JAN FEB MAR APR MAY JUN JUL AUG SEPT OCT NOV DEC

DATE OF MANUFACTURE

2019 2021 2022 20232020

0219WS026S

WARNING: ONLY USE LISTED REGENCY OPTIONS SUCH AS LEGS, AIRMATE, FAN AS SHOWN IN THE INSTALLATION MANUAL.

CAUTION: BURNING OF MATERIALS OTHER THAN SPECIFIED MAY CAUSE DAMAGE TO THE UNIT.

CAUTION: MOVING PARTS MAY CAUSE INJURY.

U.S. ENVIRONMENTAL PROTECTION AGENCY Certiﬁed to comply with 2020 particulate emission standards using cord wood.” Tested to ASTM E3053. Model Regency

F2450M – 2.3g /hr. This wood heater needs periodic inspection and repair for proper operation. Consult the owner's manual for further information. It is against federal regu-

lations to operate this wood heater in a manner inconsistent with the operating instructions in the owner's manual.

Certiﬁé conforme aux normes 2020 du U.S. ENVIRONMENTAL PROTECTION AGENCY en matière d'émission de particules de bois en utilisant le bois de corde. Approuvé

ASTM E3053. Modèle Regency F2450M – 2,3 g /h. Cet appareil de chauffage au bois doit être inspecté périodiquement et réparé pour fonctionner correctement. Consulter

le manuel d’installation pour plus d’information. La réglementation fédérale interdit de faire fonctionner un tel appareil si les consignes d'utilisation contenues dans le présent

manuel ne sont pas respectées.

MINIMUM CLEARANCES TO COMBUSTIBLE MATERIALS

DÉGAGEMENTS MINIMAUX PAR RAPPORT AUX MATÉRIAUX COMBUSTIBLES

F2450M WITH AIRMATE SHIELD F2450M WITH REAR DEFLECTOR

RESIDENTIAL INSTALLATION USING

SINGLE WALL CONNECTOR

MEASURE FLUE

FROM HEATER CENTER-LINE

RESIDENTIAL INSTALLATION USING

SINGLE WALL CONNECTOR

SIDEWALL A 406 mm / 16 in D 711 mm / 28 in

BACKWALL B 292 mm / 11.5 in E 457 mm / 18 in

CORNER C 203 mm / 8 in F 508 mm / 20 in

INSTALLATION USING LISTED DOUBLE WALL

CONNECTOR - MOBILE HOME

SIDEWALL A 381 mm / 15 in D 686 mm / 27 in

BACKWALL B 254 mm / 10 in E 419 mm / 16.5 in

CORNER C 152 mm / 6 in F 457 mm / 18 in

INSTALLATION USING LISTED DOUBLE WALL

CONNECTOR - RESIDENTIAL CLOSE CLEARANCE

SIDEWALL A 381 mm / 15 in D 686 mm / 27 in

BACKWALL B 254 mm / 10 in E 419 mm / 16.5 in

CORNER C 152 mm / 6 in F 457 mm / 18 in

INSTALLATION USING LISTED DOUBLE WALL

CONNECTOR - ALCOVE

SIDEWALL A 406 mm / 16 in D 711 mm / 28 in

BACKWALL B 241 mm / 9.5 in E 406 mm / 16 in

CORNER C 203 mm / 8 in F 508 mm / 20 in

INSTALLATION USING LISTED DOUBLE WALL

CONNECTOR - MOBILE HOME

SIDEWALL A 381 mm / 15 in D 686 mm / 27 in

BACKWALL B 203 mm / 8 in E 368 mm / 14.5 in

CORNER C 152 mm / 6 in F 457 mm / 18 in

SIDEWALL A 381 mm / 15 in D 686 mm / 27 in

BACKWALL B 203 mm / 8 in E 368 mm / 14.5 in

CORNER C 152 mm / 6 in F 457 mm / 18 in

INSTALLATION USING LISTED DOUBLE WALL

CONNECTOR - RESIDENTIAL CLOSE CLEARANCE

INSTALLATION USING LISTED DOUBLE WALL

CONNECTOR - ALCOVE

SIDEWALL G 380 mm / 15 in I 686 mm / 27 in

BACKWALL H 254 mm / 10 in J 419 mm / 16.5 in

MEASURE FLUE

FROM HEATER CENTER-LINE

SIDEWALL G 380 mm / 15 in I 686 mm / 27 in

BACKWALL H 203 mm / 8 in J 368 mm / 14.5 in

This appliance is approved for mobile home installations in Canada and the USA.

Cet appareil est homologué pour être installé dans une maison mobile au Canada et aux États-Unis.

AVERTISSEMENT : UTILISER SEULEMENT LES OPTIONS HOMOLOGUÉES PAR REGENCY COMME LES PATTES, LE DIFFUSEUR AIRMATE, LE VENTILATEUR COMME ILLUTRÉ DANE LE MANUEL D'INSTALLATION.

ATTENTION :

COMBUSTION DE TOUT MATÉRIAU NON SPÉCIFIÉ PEUT ENDOMMAGER L'APPAREIL.

ATTENTION : LE DÉPLACEMENT DES PIÈCES PEUT ENTRAÎNER DES BLESSURES.

COMBUSTION DE TOUT MATÉRIAU NON SPÉCIFIÉ PEUT ENDOMMAGER L'APPAREIL.

F2450M Regency Freestanding Woodstove | 5

dimensions

Unit Dimensions

Outside Air Dimensions

24"

610mm

817mm

879mm

690mm

630mm

163mm

860mm

798mm

198mm

21-1/4"

[540mm]

21-1/2"

[546mm]

23-1/8"

[587mm]

(from fuel door opening)

Rear

Front

Rear

4-9/16" (115mm)

6-13/16"(173mm)

Images for OUTSIDE AIR DIMENSIONS

Rear

Front

Rear

4-9/16" (115mm)

6-13/16"(173mm)

Images for OUTSIDE AIR DIMENSIONS

6 | F2450M Regency Freestanding Woodstove

installation

1. Please read this entire manual before you install

and use your new woodstove. Failure to follow

instructions may result in property damage,

bodily injury or even death. Be aware that local

Codes and Regulations may override some

items in this manual. Check with your local

inspector.

2. Select a position for your Regency Stove. Consult

the minimum clearance chart for your model

and set the stove in place. For installation use

listed double wall connector systems only.

3. To insure vertical alignment, suspend a plumb

bob from the ceiling over the exact center of

your stove ﬂue and mark a spot on the ceiling

to indicate the center of the chimney.

4. Check that the area above the ceiling is clear

for cutting. Re-conﬁrm the clearance from the

stove to combustibles to ensure that they are

within the prescribed limits.

5. This woodstove must be connected to a UL

103 HT (ULC S629) listed chimney or a code

approved masonry chimney with a ﬂue liner.

Space heater is to be connected to a factory

built chimney conforming to CAN/ULC-5629

standard for 650C factory built chimneys. The

chimney requirement is 6", refer to appropriate

sections in this manual for speciﬁcs.

6. Install chimney according to chimney manu-

facturers instructions. The performance of your

woodstove is governed to a very large part by

the chimney system. Too short a chimney can

cause difﬁcult start-up, dirty glass, back smok-

ing when door is open, and even reduced heat

output.

Too tall a chimney may prompt excessive draft

which can result in very short burn times and

excessive heat output. The use of an inexpensive

ﬂue pipe damper may be helpful in reducing

excessive draft.

CAUTION: The chimney should be the same size

as the 6" ﬂue outlet on the stove. The chimney

must be listed as suitable for use with solid fuels.

For other types of chimneys check with your

local building code ofﬁcials. Do not confuse a

chimney with a type “B” Venting System used for

gas appliances as suitable for a wood burning

appliance. For Mobile Home installations refer

to that section within this manual.

7. Mark the location of the pedestal base or legs

on the ﬂoor, then move the stove aside and

mark the position of the ﬂoor protector.

8. The ﬂoor protector must be of non-combustible

material and must extend 16" (406mm) (USA

)in front of the door opening and 8" (203mm)

to the sides and rear of the unit. Some areas

may require a larger size ﬂoor protector. See

your local inspector. For outside air installation

refer to Mobile Home installation instructions

within this manual.

11. For residential installations 6" (single wall OK)

double wall chimney, the chimney connector

must be at least 24 gauge steel. Do not use

galvanized pipe. For Mobile Home installation

refer to the Mobile Home installation instructions

within this manual.

12. DO NOT CONNECT THIS UNIT TO A CHIM-

NEY SERVING ANOTHER APPLIANCE.

13. A chimney connector cannot pass through an

attic or roof space, closet or similar concealed

space, or a ﬂoor, ceiling, wall or partition of

combustible construction. In Canada, if pas-

sage through a wall, or partition of combustible

construction is desired, the installation shall

conform to CAN/CSA-B365, Installation Code

for Solid-Fuel-Burning Appliances and Equip-

ment.

14. Your Regency Woodstove is not to be con-

nected to any air distribution duct.

CAUTION:

Do not alter or makeshift chimney or install.

Install as per Manual.

NOTE: In Canada, ﬂoor protection

must extend 18" (450mm)

to the front and 8" (203mm)

to each side and back of the

stove.

WHEN THIS ROOM HEATER IS NOT PROP-

ERLY INSTALLED, A HOUSE FIRE MAY

RESULT. TO REDUCE THE RISK OF FIRE,

FOLLOW THE INSTALLATION INSTRUC-

TIONS. CONTACT LOCAL BUILDING OR

FIRE OFFICIALS ABOUT RESTRICTIONS

AND INSTALLATION INSPECTION REQUIRE-

MENTS IN YOUR AREA.

Modular installation options

WARNING: ONLY USE SPECIFIED COMPONENTS.

The following items are required when assembling your Regency Stove. F2450M unit - the Rear Heat Deﬂector is supplied with the stove, but if you choose not to use it you must

use the Airmate instead

Modular Part

See the Minimum Clearance to Combustible Materials chart in the Installation section of this manual

F2450M Airmate OR

Rear Heat Deﬂector

Convection heat with Airmate vs. Radiant Heat with Rear Heat Deﬂector. The Airmate pushes heat forward out into the room, the Rear

Heat Deﬂector deﬂects the heat upward. Refer to the Installation sections within this manual.

OPTIONS :

Blower/ Fan

Adding the blower will increase the area heated by the stove, it can move warm air beyond the room where the stove

Ash Drawer Kit

Adding the Ash Drawer Kit makes cleaning ashes out of the stove easier and cleaner (refer to Bottom Shield Ash Drawer Kit, Instal-

lation section)

Outside Air Kit

Allows outside combustion air to enter ﬁrebox

Bottom heat shield + legs

Used instead of pedestal

Pedestal

Used instead of heat shield and legs

9. When the ﬂoor protection is complete, position

the stove with the ﬂue collar centered under the

installed chimney.

10. In areas with frequent seismic activity, Regency

recommends that your unit is secured to the

ﬂoor by using the bolt down holes inside the

pedestal (the same ones used in Mobile Home

installations).

IMPORTANT:

During the ﬁrst few ﬁres, a white ﬁlm may de-

velop on the glass front as part of the curing

process. The glass should be cleaned or

the ﬁlm will bake on and become very difﬁcult

to remove. Use a non-abrasive cleaner and

NEVER clean the glass while it is hot.

F2450M Regency Freestanding Woodstove | 7

installation

Side View

Rear Heat Deflector

Screws

Diagram 2

Diagram 3

Stove Assembly

Prior to Installation

The F2450M unit requires the pedestal (or heat

shield and legs) to be attached to the base. The

F2450M stove requires either the Airmate or Rear

Heat Deﬂector on top of the stove. Clearances to

combustible materials vary depending on whether

the Airmate or rear heat deﬂector is installed, so

be sure to check the Minimum Clearances, Instal-

lation section.

Rear Heat Deﬂector

Assembly for F2450M

The rear heat deﬂector is supplied with the stove

and must be installed unless the optional Airmate

has been selected. It stops the heat radiated from

the ﬂue collar from overheating the rear wall. The

rear heat deﬂector is installed on top of the rear

heat shield, as shown in Diagram 4.

Side Shield Adjustment

The left and right side shields are lowered for ship-

ping and handling. It allows for a handhold on the

top of the stove. Before placing the stove in its ﬁnal

position, the side shields must be raised.

Loosen the screws on the rear on the stove (3 per

side), slide the side panel up as far as possible and

then secure by tightening the screws.

Airmate

Rear Heat

Shield

Side Shield

Stove

Diagram 1

Diagram 4

Diagram 5

Airmate Assembly for F2450M

1. The Airmate sits on top of the stove with the slots

in the sides ﬁtting over the curved deﬂector on

the rear stove top. See diagram 1. Discard the

Rear Heat Deﬂector that is supplied with the

unit, it is not required if the Airmate is installed.

2. Center the Airmate and push it forward to the

front of the stove. The back of the Airmate should

be level with the back and sides of the rear heat

shield. See Diagrams 2 & 3.

8 | F2450M Regency Freestanding Woodstove

installation

F2450

920-167 12.10.19

Shown with Classic door

1. For easier assembly, tip the stove on its back (onto a soft

surface to prevent scratching) and remove the front cover.

Hint: If you have chosen the Ash Drawer option, remove

the ash dump cover plates before attaching the pedestal

(refer to the Ash drawer Kit Installation section).

2. Important: Remove the blanking plate if:

a) you are not installing outside combustion air or

b) outside air is to be brought in from the rear of the stove

(see below).

3. Using the 4 supplied 5/16" bolts in the under-side of the

stove, insert the bolts loosely onto the threads located at

all 4 corners at the base of the unit. Align the holes in the

corners of the pedestal top with the corresponding bolts

in the base of the stove. Tighten each bolt from inside the

pedestal.

1. Push the Regency logo into

the two holes in the front

bottom left corner of

the pedestal cover

plate.

Note: Any paint touch up should be done prior to placing

logo on pedestal.

2. If not using ash drawer, then the front cover must remain

in place. If using ash drawer, then remove the front cover.

The instructions below apply to the painted cast leg. It will be

easier to attach the legs to the stove if the stove is tipped on its

back (preferably on a soft surface to prevent scratching). Ensure

to be extremely careful when tipping stove.

Important: Prior to installing the bottom heat shield, remove

the 4 inch blanking plate. See below.

This must be removed for combustion air to enter the ap-

pliance.

1. Remove the 4 bolts from underside of the base of the pedestal

and discard. Also remove cover plate and put to the side.

2. Line up the heat shield with the bottom of the unit.

3. Add bre washers and washers.

4. Start threading the bolt and washer (supplied with the bot-

tom shield) for about 1/4 of the way through the leg with the

washers being underneath the legs. Ensure that the legs

are properly aligned with heat shield and tighten the bolts.

5. Level the stove by adjusting the levelling bolts in the bottom

of each leg.

6. Reinstall cover plate if not using ash drawer option.

7. Install logo plate onto heat shield by placing in 2 holes as

shown in diagram.

If you are installing outside combustion air, bend the tabs out 90

degrees. Pipe fresh air into the bottom shield by using a minimum

4" duct pipe with a mesh grill at the outside termination. Attach

the pipe to the 2 tabs with screws.

Fibre

washer

Bottom Shield

Cover

Plate

Tabs

Spacer

Leg

Leveling

Bolt

Washer

Logo

Plate

Bolt

Screw

Blanking Plate

Fibre washer

Pedestal Assembly Installation

Bottom Heat Shield and Legs Installation

Logo Installation

F2450M Regency Freestanding Woodstove | 9

installation

Room Air Important

For installation using room air for combustion,

remove knockout from the pedestal, and/or from

the bottom if using a heat shield.

Mobile home installations require the use of

outside air.

Minimum Clearance To

Combustible Materials

Please read the section below carefully as clearances depend on whether the airmate or the rear

heat deﬂector is installed on the stove.

Measurements "From Unit" are from the top plate of the stove to a side wall or to a corner, and from

the rear heat shield to a back wall.

Clearances may only be reduced by means approved by the regulatory authority.

Minimum ceiling height - 83" (2108mm)

On pedestal units there are two locations where

outside air may be adapted to the unit. If using

the bottom of the pedestal, do not remove knock-

out from the rear of the pedestal. Only remove

rear knockout if outside air will be brought in

from the rear.

On leg units outside air can only be brought in

from the bottom of the heat shield.

Note: Once the knockout is removed

there are two tabs remaining.

Bend both tabs out for ease of

installation when attaching out-

side air.

B E

NOTE: Be aware that local Codes and Regulations may override some clearances listed in this manual.

Check with your local inspector.

NOTE: This clearance is also required for air space between the appliance and wall/ceiling.

Residential Installation “C” Vent (Single Wall)

Unit From Unit From Corner From Flue Center-Line

A B C D E F

Medium F2450M with Airmate

16" (406mm) 9.5" (241mm) 8" (203mm) 28" (711mm) 16" (406mm) 20" (508mm)

with Rear Deﬂector

16" (406mm) 11.5" (292mm) 8" (203mm) 28" (711mm) 18" (457mm) 20" (508mm)

Residential Close Clearance (To be installed with required pipe components)

When the stove is installed as a close clearance residential unit, a listed double wall connector is required from the stove collar to the ceiling level.

Unit From Unit From Corner From Flue Center-Line

A B C D E F

Medium F2450M with Airmate

15" (381mm) 8" (203mm) 6" (152mm) 27" (686mm) 14.5" (368mm) 18" (457mm)

with Rear Deﬂector

15" (381mm) 10" (254mm) 6" (152mm) 27" (686mm) 16.5" (419mm) 18" (457mm)

Mobile Home Close Clearance (To be installed with required pipe components)

"C" Vent single wall pipe is not approved for Mobile Home installations. (Refer to Mobile Home Instructions.)

Unit From Unit From Corner From Flue Center-Line

A B C D E F

Medium F2450M with Airmate

15" (381mm) 8" (203mm) 6" (152mm) 27" (686mm) 14.5" (368mm) 18" (457mm)

with Rear Deﬂector

15" (381mm) 10" (254mm) 6" (152mm) 27" (686mm) 16.5" (419mm) 18" (457mm)

10 | F2450M Regency Freestanding Woodstove

installation

Floor Protection

(Ember Protection only required)

A combustible ﬂoor must be protected by a non-combustible material (like tile, concrete board, or

certiﬁed to UL-1618 Type 1, or as deﬁned by local codes).

Canada: Beneath the heater and extending to at least 18" on the fuel loading side and at least 8"

on the sides and back.

USA: Beneath the heater and extending to at least 16" beyond the fuel loading side and ash removal

opening and at least 8" on the sides and back and under the chimney connector extending 2"

beyond each side for horizontal applications.

Minimum Overall Depth (Y) of Floor Protector

Reference only when hearth pad is installed to

rear wall at minimum pipe clearances.

Hearth

Depth

Edge of Fuel door

opening to edge of

hearth

Hearth

Width

Edge of Fuel Door Opening

(Both Sides)

Residential Installation ''C'' Vent (Single Wall)

Unit

A B C D

F2450M with Airmate Canada 50-1/2" (1283mm) 18" (457mm) 33-11/16" (856mm) 8" (203mm)

USA 48-1/2" (1232mm) 16" (406mm) 33-11/16" (856mm) 8" (203mm)

F2450M with Rear

Deﬂector

Canada 52-1/2" (1334mm) 18" (457mm) 33-11/16" (856mm) 8" (203mm)

USA 50-1/2" (1283mm) 16" (406mm) 33-11/16" (856mm) 8" (203mm)

Residential Close Clearance (To be installed with required pipe components)

Unit

A B C D

F2450M with Airmate Canada 48" (1219mm) 18" (457mm) 33-11/16" (856mm) 8" (203mm)

USA 46" (1168mm) 16" (406mm) 33-11/16" (856mm) 8" (203mm)

F2450M with Rear

Deﬂector

Canada 50" (1270mm) 18" (457mm) 33-11/16" (856mm) 8" (203mm)

USA 48" (1219mm) 16" (406mm) 33-11/16" (856mm) 8" (203mm)

Minimum Alcove Clearance and Clearance to Combustible Materials

The Regency Freestanding models have been alcove approved and must be installed

with a listed double wall connector to the ceiling level.

Note: Minimum alcove ceiling height - 83"

Maximum depth of alcove - 48"

16"

405mm

NOTE: This clearance is also required for air space between the appliance and wall/ceiling. Where the

appliance is installed less than 8" from a rear wall, the ember pad only needs to extend to the base of

the wall based on the clearances noted in this manual.

Unit From Unit From Flue Center-Line From Wall

G H I J K

Medium F2450M with Airmate

15" (381mm) 8" (203mm) 27" (686mm) 14.5" (368mm) 54" (1372mm)

with Rear Deﬂector

15" (381mm) 10" (254mm) 27" (686mm) 16.5" (419mm) 54" (1372mm)

Minimum Overall Depth (Y) of Floor Protector

Edge of Fuel door

opening to edge of

hearth

Edge of Fuel Door

Opening (Both

Sides)

Unit

F2450M Canada 49" (1245mm) 18" (457mm) 33 11/16" (856 mm) 8" (203mm)

USA 47" (1194mm) 16" (406mm) 33 11/16" (856 mm) 8" (203mm)

F2450M Regency Freestanding Woodstove | 11

installation

Minimum Overall Depth (Y) of Floor Protector - Corner Hearth

Reference only when hearth pad is installed to rear wall at minimum pipe clearances.

Hearth Depth

F2450M L M N O

Residential Installation ''C'' Vent (Single Wall)

Canada 33-11/16" (856mm) 62-7/8" (1596mm) 52-1/8" (1324mm) 28-5/16" (727mm)

USA 33-11/16" (856mm) 60-7/8" (1545mm) 50-3/4" (1289mm) 26-7/8" (681mm)

Residential Close Clearance (To be installed with required pipe components)

Canada 33-11/16" (856mm) 60-1/16" (1527mm) 50-1/8" (1273mm) 26-5/16" (676mm)

USA 33-11/16" (856mm) 58-1/16" (1475mm) 48-3/4" (1238mm) 24-7/8" (610mm)

16"

for angled corners

Floor Protection (Corner Installation)

A combustible ﬂoor must be protected by non-combustible

material (like tile, concrete board, or certiﬁed to UL-1618 or

as deﬁned by local codes) extending beneath the heater and

a minimum of 8" (203mm) from each side and minimum 16"

(406mm)** from the front face of the stove and minimum 6"

(152mm)** (or the rear clearance to combustibles whichever

is smaller) from the rear of the stove.

When installed with horizontal venting, non-combustible ﬂoor

protection must beneath the ﬂue pipe and extend 2" (51mm)

beyond each side.

Minimum Overall Width (X) of Floor

Protector for all installations:

Stove F2450M 33-11/16" (856 mm)

**NOTE: In Canada, ﬂoor protection must extend 18" (450mm) to

the front and 8" (203mm) to back of the stove.

Minimum Overall Depth (Y) of Floor Protector

Unit Residential

"C" Vent

From Edge of Fuel Door

Opening

Y Z W

Medium F2450M

Canada - 49" (1245mm)

USA - 47" (1194mm)

**6" (152mm) 8" (203mm)

12 | F2450M Regency Freestanding Woodstove

installation

when using single

wall pipe

Minimum

18"

(457mm)

centerline

Horizontal Installation

Standard Ceiling Installation

8. To complete your chimney installation, install

the double wall connector pipe from the

stove’s ﬂue collar to the chimney support

device.

9. If you are using a horizontal connector,

the chimney connector should be as high

as possible while still maintaining the 18"

(457mm) minimum distance from the hori-

zontal connector to the ceiling.

NOTE: Residential Close Clearance and

Alcove installations require a listed

double wall connector from the stove

collar to the ceiling level.

The diagrams below illustrate one way to install

your unit into a standard ceiling or with a horizon-

tal connector. Check with your dealer or installer

for information on other options available to you.

Step By Step

Chimney And

Connector

Installation

Note: These are a generic set of chim-

ney installation instructions.

Always follow the manufacturers

own instructions explicitly. Check

the Minimum Recommended Flue

Heights section (Table 1).

1. With your location already established, cut

and frame the roof hole. It is recommended

that no ceiling support member be cut for

chimney and support box installation. If it is

necessary to cut them, the members must

be made structurally sound.

2. Install radiant shield and support from above.

3. Stack the insulated pipe onto your ﬁnish

support to a minimum height of 3 feet above

the roof penetration, or 2 feet above any

point within 10 feet measured horizontally.

There must be at least 3 feet of chimney

above the roof level.

Note: Increasing the chimney height

above this minimum level will

sometimes help your unit to

“breathe” better by allowing

a greater draft to be created.

This greater draft can decrease

problems such as, difﬁcult start-

ups, back-smoking when door is

open, and dirty glass. It might be

sufﬁcient to initially try with the

minimum required height, and

then if problems do arise add

additional height at a later date.

4. Slide the roof ﬂashing over your chimney

and seal the ﬂashing to the roof with rooﬁng

compound. Secure the ﬂashing to your roof

with nails or screws.

5. Place the storm collar over the ﬂashing,

sealing the joints with a silicone caulking.

6. Fasten the raincap with spark screens (if

required) to the top of your chimney.

7. For optimum efﬁciency when installing into a

masonry chimney, size accordingly, i.e. the

6" (152mm) ﬂue diameter is 28.28 sq.in.

This stove may be connected to a lined masonry

chimney or a listed factory built chimney suitable for

use with solid fuels and conforming to ULC629 in

Canada or UL-103HT in the USA. Do not connect

it to a chimney serving another appliance. To do

so will affect the safe operation of both appliances,

and will void the stove warranty. You must comply

with the local authority having jurisdiction and/or

in Canada, CSA installation standard B365-M87.

The chimney connector must be 6" diameter, 24 MSG

Black/Blue steel. Do not use aluminum or galvanized

steel, they cannot properly withstand the extreme

temperatures of a wood ﬁre. The chimney connector

between the stove and the chimney should be as

short and direct as possible.

The chimney connector must be attached to either

an approved masonry chimney or one of the listed

factory built chimneys suitable for use with solid

wood fuel. All joints must be tight and fastened with

sheet metal screws.

WARNING

THE CHIMNEY CONNECTOR IS

TO BE USED ONLY WITHIN THE

ROOM, BETWEEN THE STOVE

AND CEILING/ WALL. NEVER USE

A CHIMNEY CONNECTOR TO PASS

THROUGH AN ATTIC OR ROOF

SPACE, CLOSET OR SIMILAR CON-

CEALED SPACE, OR A FLOOR, OR

CEILING. AN EFFECTIVE VAPOR

BARRIER MUST BE MAINTAINED

AT THE LOCATION WHERE THE

CHIMNEY OR COMPONENT PENE-

TRATES TO THE EXTERIOR OF THE

STRUCTURE. ALWAYS MAINTAIN

THE MINIMUM CLEARANCES TO

COMBUSTIBLES AS REQUIRED

BY THE APPLICABLE BUILDING

CODES.

F2450M Regency Freestanding Woodstove | 13

installation

Factory Built Chimney

When a metal prefabricated chimney is used, the manufacturer's installation instructions must be followed. You must also purchase and install the

ceiling support package or wall pass-through and "T" section package, ﬁrestops (where needed), insulation shield, roof ﬂashing, chimney cap, etc.

Maintain proper clearance to the structure as recommended by the manufacturer. The chimney must be the required height above the roof or other

obstructions for safety and proper draft operation. The space heater is to be connected to a factory-built chimney conforming to CAN/ULC-S629,

Standard for 650

C Factory-Built Chimneys.

Masonry

Chimney

Ensure that a masonry chimney meets the mini-

mum standards of the National Fire Protection

Association (NFPA) by having it inspected by

a professional. Make sure there are no cracks,

loose mortar or other signs of deterioration and

blockage. Have the chimney cleaned before the

stove is installed and operated. When connect-

ing the stove through a combustible wall to a

masonry chimney, special methods are needed.

Ensure that an effective vapour barrier at the

location where the chimney or other component

penetrates to the exterior of the structure.

Masonry

Fireplace

There are listed kits available to connect a stove

to a masonry ﬁreplace. The kit is an adapter

that is installed at the location of the ﬁreplace

damper. The existing damper may have to be

removed to allow installation.

Ensure that an effective vapour barrier at the

location where the chimney or other component

penetrates to the exterior of the structure.

This unit is designed to use either a 5.5" (140mm)

or 6" (152mm) ﬂue liner only in the conﬁnes of

the masonry chimney as shown.

Minimum 18" (457mm)

to centerline

Minimum

18"

(457mm

)

centerline

When referencing installation or connection to

masonry ﬁreplaces or chimneys, the masonry

construction must or shall be code complying.

When referencing installation or connection to

masonry ﬁreplaces or chimneys, the masonry

construction must or shall be code complying.

14 | F2450M Regency Freestanding Woodstove

installation

Method A: 12" (304.8 mm) Clearance to Combustible Wall Member:

Using a minimum thickness 3.5" (89 mm) brick and a 5/8" (15.9 mm)

minimum wall thickness clay liner, construct a wall pass-through.

The clay liner must conform to ASTM C315 (Standard Speciﬁcation

for Clay Fire Linings) or its equivalent. Keep a minimum of 12" (304.8

mm) of brick masonry between the clay liner and wall combustibles.

The clay liner shall run from the brick masonry outer surface to the

inner surface of the chimney ﬂue liner but not past the inner surface.

Firmly grout or cement the clay liner in place to the chimney ﬂue liner.

Method B: 9" (228.6 mm) Clearance to Combustible Wall Member:

Using a 6" (152.4 mm) inside diameter, listed, factory-built Solid-Pak

chimney section with insulation of 1" (25.4 mm) or more, build a wall

pass-through with a minimum 9" (228.6 mm) air space between the

outer wall of the chimney length and wall combustibles. Use sheet metal

supports fastened securely to wall surfaces on all sides, to maintain the

9" (228.6 mm) air space. When fastening supports to chimney length,

do not penetrate the chimney liner (the inside wall of the Solid-Pak

chimney). The inner end of the Solid-Pak chimney section shall be

ﬂush with the inside of the masonry chimney ﬂue, and sealed with a

non-water soluble refractory cement. Use this cement to also seal to

the brick masonry penetration.

Minimum

12 in. (304.8mm)

to combustibles

Masonry chimney

Chimney Flue

Minimum chimney clearance to brick

and combustibles 2 in. (50.8mm)

Minimum clearance

12 in. (304.8mm)

of brick

Chimney

connector

Fire clay

liner

Method C: 6" (152.4 mm) Clearance to Combustible Wall Member:

Starting with a minimum 24 gage (.024" [.61 mm]) 6" (152.4 mm) metal

chimney connector, and a minimum 24 gage ventilated wall thimble

which has two air channels of 1" (25.4 mm) each, construct a wall

pass-through. There shall be a minimum 6" (152.4 mm) separation

area containing ﬁberglass insulation, from the outer surface of the wall

thimble to wall combustibles. Support the wall thimble, and cover its

opening with a 24-gage minimum sheet metal support. Maintain the

6" (152.4 mm) space. There should also be a support sized to ﬁt and

hold the metal chimney connector. See that the supports are fastened

securely to wall surfaces on all sides. Make sure fasteners used to

secure the metal chimney connector do not penetrate chimney ﬂue liner.

Method D: 2" (50.8 mm) Clearance to Combustible Wall Member:

Start with a solid-pak listed factory built chimney section at least 12"

(304 mm) long, with insulation of 1" (25.4 mm) or more, and an inside

diameter of 6" (2 inches [51 mm] larger than the 6" [152.4 mm] chimney

connector). Use this as a pass-through for a minimum 24-gage single

wall steel chimney connector. Keep solid-pak section concentric with

and spaced 1" (25.4 mm) off the chimney connector by way of sheet

metal support plates at both ends of chimney section. Cover opening

with and support chimney section on both sides with 24 gage minimum

sheet metal supports. See that the supports are fastened securely to

wall surfaces on all sides. Make sure fasteners used to secure the

metal chimney connector do not penetrate chimney ﬂue liner.

Combustible Wall Chimney Connector Pass-throughs

F2450M Regency Freestanding Woodstove | 15

installation

Pedestal

Bolted to

Floor

Outside Air

Mobile Home Installation

Once you have properly marked the position of

your unit and the ﬂoor protection as outlined in

the Residential Installation items #1 through #8, a

supply of fresh air has to be supplied to your unit.

See Optional Outside Air Kit instructions in this

manual.

Place your unit in position and secure it to the ﬂoor

using two lag bolts 3/8" (10mm) x 3-1/2" (89mm)

through the two holes inside the pedestal base.

It is important to maintain the structural integrity

of the Mobile Home ﬂoor, walls and roof when

installing your unit.

For Mobile Home units installed in the U.S. the unit

must be grounded using a #8 ground wire with

approved termination and star washer.

In addition to standard installation instructions the

following requirements are mandatory for installation

in a mobile home.

1. The stove must be permanently bolted to

the ﬂoor of the Mobile Home using the ﬂoor

screws provided.

2. The stove must have a permanent outside air

source for combustion.

3. The stove must be electrically grounded to the

steel chassis of the Mobile Home.

4. A listed double-wall connector chimney system,

roof thimble, spark arrestor and roof ﬂashing kit

suitable for use in Mobile Homes must be used.

5. If the chimney exits the Mobile Home at a location

other than through the roof, and exits at a point

7ft. (2130mm) or less above the ground level on

which the Mobile Home is positioned a guard or

method of enclosing the chimney shall be ﬁtted at

the point of exit for a height up to 7ft. (2130mm).

6. The chimney shall be attached directly to the room

heater and shall extend at least 3 ft. (914mm)

above the part of the roof through which it passes.

The top of the chimney should project at least

2ft. (610mm) above the highest elevation of any

part of the Mobile Home within 10 ft. (3048mm)

of the chimney.

7. The chimney system shall comply with Local

Requirements.

8. Any openings in a chimney guard where required

must not permit the entrance of 3/4" (19mm)

diameter rod.

9. CAUTION: THE STRUCTURAL INTEGRITY OF

THE MOBILE HOME ROOF, FLOOR, WALLS

AND CEILING MUST BE MAINTAINED.

10. Check any other local building code as other

local codes may apply.

11. WARNING: DO NOT INSTALL IN A SLEEPING

ROOM OF A MOBILE HOME.

12. Use silicone to create an effective vapour barrier

at the location where the chimney or other com-

ponent penetrates to the exterior of the structure.

CAUTION: At no time use unlabelled

parts, or substitute parts made for another

chimney system.

Install as per chimney manufacturer's

installation instructions.

For Canadian Installations : see Outside Air

Kit - Part # 846-502.

There are further requirements when installing

this unit into a mobile home in Canada only.

WARNING: Operate only with door fully

closed - open feed door to feed ﬁre only.

1. Identify the position of the outside air damper by the orientation of the metal handle that rests outside

the galvanized pipe. The metal handle and the damper disc are in line with each other. This means

that if the metal handle is in a horizontal position, the damper is ﬂat and fully open.

2. Open the damper fully whenever you start a ﬁre. This will allow the outside air to be drawn in the

pedestal base eliminating any potential smoke escaping the stove and entering the room. (Negative

air pressure)

16 | F2450M Regency Freestanding Woodstove

installation

Mobile Home Kit - for Canada

Note: The optional ashdrawer cannot be used when using the Mobile Home Kit.

920-167

28.10.19

F2450

Mobile Home Kit - For Canada

Note: The optional ash drawer cannot be used when using the Mobile Home Kit.

Remove the 4" knock out from the rear pedestal.

Install rear collar to the rear pedestal using 4 screws.

Page 1 of 1 075-500.SLDASM 12/19/2016

Mobile Home Box

Pedestal Stove

Collar

Flex

The Mobile Home kit contains:

1 Bottom metal cover - only used when air is drawn from the ﬂoor.

1 Flex

1 Collar

1 Mobile home box

1 Square transition box (used when installing bottom heat shield/

legs)

Screws

5. Attach ﬂex to rear pedestal using supplied screws or the 4" clamp.

6. Bring pedestal base near the base of the ﬁrebox and secure ﬂex

to the Mobile Home box.

7. Secure pedestal base and Mobile Home Box to ﬁrebox as shown

in diagram 3 using the screws that were previously removed/

loosened in step 1. See pedestal instructions.The Mobile Home

Box and ﬁrebox use the same screws.

Diagram 4

8. Install blanking plate to the front of the pedestal with 4 screws.

Lay unit on its back. Remove two front 7/16 bolts. Loosen rear

two 7/16" bolts. See diagram 1.

  

Install rear collar

to the rear pedes-

tal using 4 screws.

Diagram 2

Diagram 3

4 screws

Diagram 5

9. Place unit into position and install the mandatory outside air kit.

See «Mobile Home installation» section in this manual.

Blanking

plate

If using outside air from the rear of the pedestal, follow instruc-

tions noted below. If using outside air from the pedestal base,

follow instructions from step 10 to 16. For bottom heat shield/

legs, follow instructions from step 17 to 22. The Mobile Home Box

is always mounted in between the ﬁrebox and pedestal or bottom

heat shield.

Diagram 1

F2450M Regency Freestanding Woodstove | 17

installation

920-167 12.10.19

If installing outside air from pedestal base, do not remove knock

out from rear of pedestal. This must remain in place.

Page 1 of 1 075-500.SLDASM 12/19/2016

Mobile Home Box

Flex

Bottom Metal Cover

Collar

Pedestal Base

10. Secure collar to base of unit with 4 screws.

11. Install bottom metal cover over collar installed in step 10 and

rest cover on pedestal base.

12. Secure flex to collar with supplied screws or the 4" clamp.

13. Bring pedestal base near the base of the firebox and secure flex

to mobile home box with supplied screws.

14. Secure Mobile Home Box and pedestal to the firebox base

using the screws that were previously removed in step 1. See

pedestal instructions.

15. Install blanking plate to the front of the pedestal with 4 screws.

Use picture from step 8.

16. Install the mandatory outside air kit. See «Mobile Home Instal-

lation» section in this manual. Place unit into its final position

to complete install.

Installing Outside Air Using Bottom Heat

Shield/Legs

Page 1 of 1 075-500.SLDASM 12/19/2016

Mobile Home Box

Square Transition Box

Collar

Bottom Heat Shield

Cast legs

Knock out

Blanking plate

17. Remove knock out from the bottom heat shield and bend tabs left

over when the knock out was removed to the side.

18. Secure collar to base of bottom heat shield as shown with 4 screws.

19. Secure transition box on top of round collar installed in step 18

and secure with 3 screws.

20. Install blanking plate if not already installed.

21. Secure Mobile Home Box and bottom heat shield. See bottom

heat shield/leg instructions.

22. Install the mandatory outside air kit. See «Mobile Home Instal-

lation» section in this manual. Place unit into its final position to

complete install.

F2450

Installing Outside Air from Pedestal Base

18 | F2450M Regency Freestanding Woodstove

installation

Recommended Heights For Woodstove Flue

Simple rules on draft. See Table 1.

1) At sea level minimum height is 12' straight.

2) Add the following vertical height to compensate for:

45 deg. elbow = 1 ft.

90 deg. elbow = 2 ft.

"T" = 3 ft.

Each foot of horizontal run = 2 ft.

3) Add 4% overall for each 1000' above sea level.

Example: a)

1-1/2 ft. of horizontal run = 3 ft.

one "T" = 3 ft.

Total Addition (at sea level) = 6 ft.

Example: b)

One 90 deg. elbow = 2 ft.

2 ft. of horizontal run = 4 ft.

one "T" = 3 ft.

Total Addition (at sea level) = 9 ft.

Recommended Flue Height

Elevation Example a) Example b)

0' 18' 21'

1000' 18.72' 21.84'

2000' 19.44' 22.68'

5000' 21.60' 25.20'

8000' 23.76' 27.72'

TABLE 1

MINIMUM RECOMMENDED FLUE HEIGHTS IN FEET

(Measured from the top of the unit)

# OF ELBOWS

ELEVATION (FT)

ABOVE SEA LEVEL 0 2 x 15

4 x 15

2 x 30

4 x 30

2 x 45

4 x 45

0-1000 12.0 13.0 14.0 15.0 18.0 16.0 20.0

1000-2000 12.5 13.5 14.5 15.5 19.0 16.5 21.0

2000-3000 13.0 14.0 15.0 16.0 19.5 17.0 21.5

3000-4000 13.5 14.5 15.5 17.0 20.0 18.0 22.5

4000-5000 14.0 15.0 16.0 17.5 21.0 18.5 23.0

5000-6000 14.5 15.5 17.0 18.0 21.5 19.0 24.0

6000-7000 15.0 16.0 17.5 18.5 22.5 20.0 25.0

7000-8000 15.5 16.5 18.0 19.0 23.0 20.5 25.5

8000-9000 16.0 17.0 18.5 20.0 24.0 21.0 26.5

9000-10000 16.5 17.5 19.0 20.5 24.5 22.0 27.0

NOTE: No more than two offsets (four elbows) allowed. Two 45

elbows equal one 90

elbow.

WARNING:

DO NOT INSTALL IN SLEEPING

ROOM

CAUTION: The structural integrity of the mobile home

ﬂoor, wall and ceiling/roof must be maintained.

Draft is the force which moves air from the appliance

up through the chimney. The amount of draft in your

chimney depends on the length of the chimney, local

geography, nearby obstructions and other factors.

Too much draft may cause excessive temperatures

in the appliance and may cause damage. An un-

controllable burn or excessive temperature indicates

excessive draft. Inadequate draft may cause back

pufﬁng into the room and plugging of the chimney.

Inadequate draft will cause the appliance to leak

smoke into the room through appliance and chim-

ney connector joints. Ensure the heater is installed

in areas that are not too close to neighbors or in

valleys that would cause unhealthy air quality or

nuisance conditions.

F2450M Regency Freestanding Woodstove | 19

installation

The Outside Air Kit is an option for Freestanding Stoves. Outside air for combustion can be brought in either through the bottom of the pedestal or

through the rear plate of the pedestal.

For both bottom and rear outside air the Pedestal Cover Plate must be installed. Loosen the 4 screws on the rear of the pedestal and slide the cover

plate over them. Slide the plate to the left to center it and tighten down the 4 screws.

Rear View

Completed Install

Side View

Outside Air Through Pedestal Bottom

Mark the position of your unit as outlined in the "General Information"

and "Clearances to Combustibles" section of the manual. Pipe fresh

air into the pedestal area by using a minimum 4" duct pipe with a

mesh grill at the outside termination.

Outside Air Through Pedestal Rear

Remove the blanking plate from the rear of the pedestal and bend

the two tabs out 90 degrees. Pipe fresh air into the pedestal area

by using a minimum 4" metallic duct pipe with a mesh grill at the

outside termination.

Fasten the pipe to the cover plate using the tabs and 2 screws.

Damper Installation

NOTE: The damper cannot be installed if attaching outside air to the

bottom of the appliance.

Supplied damper allows the combustion air to be closed off when unit

is not in operation.

Install the damper within the round pipe in an easily accessible location.

1. Drill a 5/16" hole in the desired location.

2. Insert damper with threaded section out.

3. Install damper handle and secure with wing nut.

Wing nut

Damper handle

Damper

Optional Outside Air Kit

20 | F2450M Regency Freestanding Woodstove

installation

Brick Installation

Firebrick is included to extend the life of your stove and radiate heat more evenly. Check to see that all ﬁrebricks are in their correct positions and have not

become misaligned during shipping. Install all ﬁrebricks (if bricks were removed at install) per the diagram below and place in their correct positions.

Do not use a grate.

NOTE: The "AD" brick in the drawings above is the brick covering the Ash Dump hole that is used when the Ash Drawer Kit is installed (refer

to the Listed Components for Mobile Home Installation section).

LyTherm sheet

Order of ﬁrebrick install:

a) Rear Firebrick

b) Firebox ﬂoor - install brick over LyTherm Sheet

c) Right and left side Firebricks

70) Brick - Regular Full Size: 1-1/4" x 4-1/2" x 9"

72) Brick Partial: 1-1/4" x 2" x 4-1/2"

74) Brick Partial: 1-1/4" x 4-1/2" x 3-1/2"

76) Brick Partial: 1-1/4" x 2" x 9"