LG Electronics TA4HEB-N2 Manuel utilisateur

Taper
Manuel utilisateur
LG Electronics Inc. 1 19-4-8
JLR VDC User Manual
TA4HEB-N2 Introduction
VDC (Vehicle Domain Controller)
Telematics module device equipped in the JLR(Jaguar Land Rover) vehicles.
In charge of wireless communications in LTE-A/LTE/WCDMA/GSM network
Platform for Telematics Virtual Machine (VM) and other VMs based on Hypervisor
TA4HEB-N2 supports GSM850/1900, WCDMA B2/4/5, LTE B2/4/5/7/12/26, 2.4/ 5GHz WLAN (UNII 1, 3)
Service types which are provided by VDC
Voice service : eCall, bCall1) via TSP2)
SMS service : MO/MT SMS between Telematics VM TSP2)
Data service : Telematics services between Telematics VM TSP
1/10
LG Electronics Inc. 2 19-4-8
Major functions of VDC (TA4HEB-N2)
Multi-mode LTE, Wi-Fi 11ac-Client, Ethernet connection.
Micom for a vehicle interface and a power control, AP for an Ethernet interface and Wi-Fi operation
Audio circuitry for Emergency Call and Breakdown Call.
Cellular
Wi-Fi
Mode/Band Frequency Band (MHz)
802.11b, g, n / 2.4GHz 2412 ~ 2462
802.11a, n, ac / 5GHz 5180~5240, 5745~5825
VDC (Vehicle Domain Controller) supports highly integrated multimode, multiband RF CMOS transceiver IC. It
provides a single-chip solution for LTE carrier aggregation support up to 20 MHz+20 MHz for 2DLCA. For the
WiFi, Qualcomm engine are used. Overall the VDC directly supports with up to 2 GSM bands, 3UMTS bands
and 6 FDD-LTE bands with 2DLCA. Additional Qualcomm IC as QCA6574 support WiFi 11ac.
VDC is operating with LGE shark antenna approved for use with the device.
2/10
RFx information
The strength of the RF field produced by the wireless module or modules
embedded in the TCU is well within all international RF exposure limits known
at this time. Because the wireless modules embedded in the TCU emit less than
the maximum amount of energy permitted in radio frequency safety standards
and recommendations, the manufacturer believes these modules are safe for
use.
Regardless of the power levels, care should be taken to minimize human
contact during normal operation. This module should be remain more than 20
cm (8 inches) from the body when wireless devices are on and transmitting.
This transmitter must not be collocated or operated in conjunction with any
other antenna or transmitter. Operation is subject to the following two conditions:
(1) this module does not cause interference , (2) this module accepts any
interference that may cause undesired operation.
Information for the integrator
The integrator must not provide information to the end user regarding how to
install or remove this RF module in the user manual of the end product. The user
manual that is provided by the integrator for end users must include the following
information in a prominent location. To comply with FCC RF and IC RSS102
exposure requirements, the antenna used for this transmitter must be installed to
provide a separation distance of at least 20 cm from all persons and must not
be collocated or operated in conjunction with any other antenna or transmitter.
Approbation FCC
This module complies with FCC/IC rules.
FCC : Part 15, Part 22, Part 24, Part 27, Part 90
ISED : RSS-130, RSS-132, RSS-133, RSS-139, RSS-199, RSS-247
Furthermore, this device complies with FCC radiation exposure limits set forth for uncontrolled
environments.
This module must be installed and operated with minimum distance of 20 cm between the
radiating element and the user.
This module must not be co-located with any other transmitters or antennas.
To comply with FCC regulations limiting both the maximum RF output power and human
exposure to RF radiation, the maximum antenna gain including cable loss in a mobile-only
exposure condition must not exceed the values listed in the following table.
Band Frequency Range
[MHz] Maximum Antenna
Gain[dBi]
GSM850 824~849 -3.57
GSM1900 1850~1910 0.01
WCDMA(B2) 1850~1910 0.01
WCDMA(B4) 1710~1755 0.33
WCDMA(B5) 824~849 -3.57
LTE(B2) 1850~1910 0.01
LTE(B4) 1710~1755 0.33
LTE(B5) 824~849 -3.57
LTE(B7) 2500~2690 -3.61
LTE(B12) 699~716 -2.61
LTE(B26) 814~849 -4.30
Approbation FCC
To satisfy the FCC’s exterior labeling requirements, the following text must appear on the
exterior of the end product.
Contains transmitter module FCC ID: BEJTM05GTJN2
Contains transmitter module IC: 2703H-TM05GTJN2
Changes or modifications to this equipment may cause harmful interference unless the
modifications are expressly approved in the instruction manual. Users may lose the authority
to operate this equipment if an unauthorized change or codification is made.
Note: If this module is intended for use in a portable device, additional testing will be required
to satisfy the RF exposure and SAR requirements of FCC Part 2.1093 and RSS-102.
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired
operation.
Approbation FCC
Note: The OEM integrator is responsible for ensuring that the host product which is installed
and operating with the module is in compliant with Part 15B unintentional Radiator
requirements, please note that For a Class B digital device or peripheral, the instructions
furnished the user manual of the enduser product shall include the following or similar
statement, placed in a prominent location in the text of the host product manual:
NoteThis equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation.
If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux
CNR d’Innovation, Sciences et Développement économique Canada applicables aux
appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions
suivantes :(1)L’appareil ne doit pas produire de brouillage; (2)L’appareil doit accepter tout
brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le
fonctionnement.
L’étiquette d’homologation d’un module d’Innovation, Sciences et Développement
économique Canada devra être posée sur le produit hôte à un endroit bien en vue, en tout
temps. En l’absence d’étiquette, le produit hôte doit porter une étiquette sur laquelle figure le
numéro d’homologation du module d’Innovation, Sciences et Développement économique
Canada, précédé du mot « contient », ou d’une formulation similaire allant dans le même
sens et qui va comme suit :
Contient IC : 2703H-TM05GTJN2 est le numéro d’homologation du module.
Cet équipement est conforme aux limites d'exposition aux radiations IC CNR102 établies
pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec une
distance minimale de 20 cm entre le radiateur et votre corps.
Approbation IC
The device apply the following requirements persuant to RSS-247 additional requirement.
i. the device for operation in the band 5150–5250 MHz is only for indoor use to
reduce the potential for harmful interference to co-channel mobile satellite
systems.
ii. for devices with detachable antenna(s), the maximum antenna gain permitted
for devices in the bands 5250-5350 MHz and 5470-5725 MHz shall be such that
the equipment still complies with the e.i.r.p. limit.
iii. for devices with detachable antenna(s), the maximum antenna gain permitted
for devices in the band 5725-5850 MHz shall be such that the equipment still
complies with the e.i.r.p. limits as appropriate.
iv. where applicable, antenna type(s), antenna models(s), and worst-case tilt
angle(s) necessaryto remain compliant with the e.i.r.p. elevation mask
requirement set forth in section 6.2.2.3 shall be clearly indicated.
WiFi Antenna Specification
f[MHz] value f[MHz] value
2412 2.14 5150 3.96
2417 2.12 5200 3.39
2422 2.32 5250 2.47
2427 2.55 5300 3.67
2432 2.53 5350 3.67
2437 2.27 5400 3.07
2442 2.24 5450 3.96
2447 2.41 5500 4.07
2452 2.13 5550 4.74
2457 1.96 5600 5.74
2462 1.76 5650 6.28
5700 5.89
5750 6.21
5800 6.31
5850 5.81
5900 6.24
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7

LG Electronics TA4HEB-N2 Manuel utilisateur

Taper
Manuel utilisateur

dans d''autres langues