LG Innotek YZP-BH1000 Manuel utilisateur

User Guide for the LTD-BH1000

1. Overview

2. Major features

3. Interface

4. Electrical specifications

5. RF specifications

6. Mechanical specifications

7. General specifications

8. Connectors

9. RFx information

10. FCC approval

Table of Contents

Product: WCDMA Wireless Modem

Model name: LTD-BH1000

The LTD-BH1000 is a personal mobile communication device that incorporates

the latest compact radio technology, including smaller and lighter components

and support for WCDMA(850/1900MHz) bands. This device acts as the

vehicle’s telematics system and connects to WCDMA (HSPA+) wireless

networks and wireless modules to allow voice and data communication.

Furthermore, this device can operate on land and water as well as other similar

areas.

In HSPA+ mode, the device provides uplink speeds of up to 5.76 Mbps and

downlink speeds of up to 14.4 Mbps for seamless transfer of data such as

movies and video calls. The device also supports the transfer of large amounts

of data.

The device communicates with the host system via a standard RS-232 or USB

port, and AT commands and control commands can be used to send data. Voice

calls are also possible.

1. Overview

Mechanical

Dimensions

93.7(L) x 42(W) x 7.6(T) mm

Weight

TBD g (max)

Interface

USB, general purpose I/O pins

Antenna

FAKRA connector

Temperature*

Operation: -20 ℃ - +70 ℃

Storage: -40 ℃ - +85 ℃

Technology

Main chipset

MDM 6200

Memory

1024Mb(NAND) / 512Mb(SDRAM)

Standard

3GPP WCDMA (HSPA+)

- DL Speed : 14.4 Mbps

- UL Speed : 5.76 Mbps

Band

WCDMA B2, B5

Power

WCDMA : Typ. 24dBm (Power Class 3)

ETC

DC power

4 V

Functions

Voice, data, SMS

2. Major features

3. Interface

Customer P/N is connected with outer device using 40 pin connector

3.1 Pin output

Figure 1. Connector pin arrangement

NC 1 2 NC

GND 3 4 GND

NC 5 6 NC

NC 7 8 NC

NC 910 NC

BOOT_OK 11 12 MSG

NC 13 14 NC

NC 15 16 PCM_3.3V_TXD

GND 17 18 PCM_3.3V_RXD

PCM_3.3V_CLK 19 20 PCM_3.3V_SYNC

GND 21 22 GND

NC 23 24 NC

NC 25 26 NC

96H_END 27 28 RESET_IN

USB_VBUS 29 30 ACC_ON_SLEEP

V_BATT 31 32 V_BATT

GND 33 34 GND

GND 35 36 USB_D-

UART_RXD 37 38 USB_D+

UART_TXD 39 40 GND

3. Interface

3.2 Pin description

Table 1. Pin descriptions

Signal Name Type Pin Description

USB

USB_D

+

USB_D

-

USB_VBUS

IO

I

38

36

29

USB

differential data line (+)

USB

differential data line (-)

USB

power Supply

Audio

PCM

PCM_3.3V_SYNC

PCM_3.3V_CLK

PCM_3.3V_TXD

PCM_3.3V_RXD

I

O

I

20

19

16

18

PCM

interface sync

PCM

interface clock

PCM interface digital audio data out

PCM

interface digital audio data in

User

Interface

BOOT_

OK

RESET_IN

MSG

96H_END

ACC

_ON_SLEEP

O

I

O

I

11

28

12

27

30

Indicates that the Modem boot is complete.

Control line to unconditionally restart the module.

Indicates

that the Modem receive

Urgent message.

Indicates

that the 96hr sleep mode is end.

Control line to power on or 96hr

sleep mode.

Power

VBATT

GND

I

-

31,32

3,4,17,21,22,33

,35,40

Power supply

input (+)

Power supply

input (-)

UART

UART_RXD

UART_TXD

I

O 37

39

UART RX

DATA

UART TX DATA

NC

RESERVED

-

1,2,5,6,7,8,9,10

,13,14,15,23,24

,25,26

Reserved pins. Please leave

these unconnected

3. Interface

3.3 USB

This device supports universal serial bus (USB) connections for high-speed

data communication. The relevant hardware satisfies the USB 2.0

specifications and supports maximum communications speeds of 480 Mbps

Table 2. USB Pin descriptions

Pin NO. Signal Name Pin I/O

(Modem host) Function Description

38 USB_D+ IO USB Differential data line (+)

36 USB_D- IO USB Differential data line (-)

29 USB_VBUS I USB Power Supply

3. Interface

3.4 Audio

This module includes a PCM interface. The pull-up and pull-down resistors

attached to these pin must provide more than 50 Kohm of resistance.

Table 3. PCM Pin descriptions

3.5 User interface

Pin No.

Signal Name Direction

Function

11 BOOT_OK O Indicates that the Modem boot is complete.

28 RESET_IN I Control line to unconditionally restart the

module.

12 MSG O Indicates that the Modem receive Urgent

message.

27 96H_END O Indicates that the 96hr sleep mode is end.

30 ACC_ON_SLEEP

I Control line to power on or 96hr sleep mode.

Table 4. User interface Pin descriptions

Pin NO.

Signal Name Pin I/O

(Modem host) Function Description

20 PCM_3.3V_SYNC

I PCM Interface sync

19 PCM_3.3V_CLK

I PCM Interface clock

16 PCM_3.3V_TXD

O PCM Interface digital audio data out

18 PCM_3.3V_RXD I PCM Interface digital audio data in

4. Electrical specifications

4.1 Power supply specifications

The host system provides the power supply (V_BATT)DC 4 V, 1.5 A to the

device. The internal power supply module manages the power supplied to the

integral circuits and maintains constant voltages. This module also controls

each power block to minimize power consumption.

In particular, the PAM (power amplifier module) consumes a lot of power, so it

receives a direct power supply of 4 V from the V_BATT. Therefore the

V_BATT signal inputs only the supply power of the PAM, even when the

absolute rating is higher. In addition, the entire power input module blocks and

protects against high surges and ESD in the NAD module.

Pin No. Signal Name Direction MIN TYP MAX

31,32 V_BATT I TBD V 4 V TBD V

Table 5. Power supply specifications

4. Electrical specifications

4.2 Logic level specifications

4.2.1 Digital logic level specifications

Table 6. Digital logic level specifications

Signal Name Type Low High Unit

Min Max Min Max

BOOT_OK O -0.3 0.63 1.17 2.1

V

RESET_IN I 0 0.45 1.35 1.8

MSG O -0.3 0.63 1.17 2.1

96H_END O -0.3 0.63 1.17 2.1

ACC_ON_SLEEP

I 0 0.45 1.35 1.8

5. RF specifications

5.1 WCDMA

5.1.1 Receiver

.- Bandwidth : 5MHz

.- Frequency : 869MHz – 894MHz (B5), 1930MHz – 1990MHz (B2)

.- RF to Baseband Direct conversion (Zero IF)

.- Modulation method : QPSK, 16QAM

.- Sensitivity : ≤-104dBm (BER = Under 0.1%)

5.1.2 Transmitter

.- Frequency: 824MHz – 849MHz (B5), 1850MHz – 1910MHz (B2)

.- Maximum RF Output : Power class3 , 20.3dBm ~ 25.7dBm

.- Modulation method : QPSK

.- Baseband to RF Direct conversion (Zero IF)

6. Mechanical specifications

6.1 Environment specifications

.- Storage temp.: -40 ℃ - +85 ℃

.- Operating temp.: -20 ℃ - +70 ℃

(-20 ℃ - +70 ℃ : 3GPP specifications are satisfied

-30 ℃ - -20 ℃, +70 ℃ - +80 ℃ : May cause performance degradation)

.- Operating humidity: 80% (60℃) relative humidity

6. Mechanical specifications

6.1 Mechanical dimensions

Dimensions 93.7(L) x 42(W) x 7.6(T) mm

Weight 36.6 grams(max.)

Modem interface connector 12709HS-H40 (Manufacture vendor : YUNHO)

Modem antenna Connector (Plug) 59S21B-40MT5-D

(Manufacture vendor : Rosenberger)

Table 7. Mechanical specification

Figure 2. Mechanical dimension

7. General specifications

7.1 WCDMA B5 electrical specifications

Table 9. WCDMA B5 RF specification

TEST ITEM Spec. Test Temperature Test Freq

uency

CHANNEL

4357 4400 4458

1 Maximum Output Power 20.3~25.7dBm Normal, Temp L, Te

mp H Low, Mid,

High PASS

PASS

2 Frequency Error -195 ~ +195Hz Normal, Temp L, Te

mp H Low, Mid,

High PASS

PASS

3 Inner Loop Power Control in the Uplin

k PASS Normal Mid - PASS

-

4 Minimum Output Power -49dBm ↓ Normal, Temp L, Te

mp H Low, Mid,

High PASS

PASS

5 Occupied Bandwidth (OBW) 5MHz ↓ Normal Low, Mid,

High PASS

PASS

6 Spectrum emis

sion mask

SEM Band1 Offset2.

5-3.5MHz (at Freq+3.

5MHz) -48.5dBc ↓

Normal Low, Mid,

High

PASS

SEM Band1 Offset3.

5-7.5MHz (at Freq+7.

5MHz) -37.5dBc ↓ PASS

PASS

SEM Band1 Offset7.

5-8.5MHz (at Freq+8.

5MHz) -47.5dBc ↓ PASS

PASS

SEM Band1 Offset8.

5-12.5MHz -47.5dBc ↓ PASS

PASS

7

Adjacent Chan

nel Leakage Po

wer Ratio (ACL

R)

ACLR Offset +5/-5M

Hz Rel -32.2dBc ↓ Normal, Temp L, Te

mp H Low, Mid,

High PASS

PASS

ACLR Offset +10/-10

MHz Rel -42.2dBc ↓ Normal, Temp L, Te

mp H Low, Mid,

High PASS

PASS

8 Error Vector M

agnitude(EVM)

EVM at Tx output po

wer 24dBm /-18dBm 17.5% ↓ Normal Low, Mid,

High PASS

PASS

9 Peak code do

main error PCDE at Tx output p

ower 24dBm/-18dBm

-14dB ↓ Normal Low, Mid,

High PASS

PASS

10 Phase Disconti

nuity

Phase Discontinuity

max EVM 17.5% ↓

Normal Mid

- PASS

-

Phase Discontinuity

max Frequency Error

-195~195Hz - PASS

-

Phase Discontinuity

max 1500Hz 36 degrees ↓ - PASS

-

11 Reference Sen

sitivity Level

Ref Sense Go/No Go

I^or=-104dBm/3.84M

Hz BER 0.1% ↓ Normal, Temp L, Te

mp H Low, Mid,

High PASS

PASS

12 Maximum Inpu

t Level

Max Input Go/No Go

I^or=-25.7dBm/3.84M

Hz BER 0.1% ↓ Normal Mid - PASS

-

7. General specifications

7.2 WCDMA B2 electrical specifications

Table 10. WCDMA B2 RF specification

TEST ITEM Spec. Test Temperature Test Freq

uency

CHANNEL

9662 9800 9938

1 Maximum Output Power 20.3~25.7dBm Normal, Temp L, Te

mp H Low, Mid,

High PASS

PASS

2 Frequency Error -195 ~ +195Hz Normal, Temp L, Te

mp H Low, Mid,

High PASS

PASS

3 Inner Loop Power Control in the Uplin

k PASS Normal Mid - PASS

-

4 Minimum Output Power -49dBm ↓ Normal, Temp L, Te

mp H Low, Mid,

High PASS

PASS

5 Occupied Bandwidth (OBW) 5MHz ↓ Normal Low, Mid,

High PASS

PASS

6 Spectrum emis

sion mask

SEM Band1 Offset2.

5-3.5MHz (at Freq+3.

5MHz) -48.5dBc ↓

Normal Low, Mid,

High

PASS

SEM Band1 Offset3.

5-7.5MHz (at Freq+7.

5MHz) -37.5dBc ↓ PASS

PASS

SEM Band1 Offset7.

5-8.5MHz (at Freq+8.

5MHz) -47.5dBc ↓ PASS

PASS

SEM Band1 Offset8.

5-12.5MHz -47.5dBc ↓ PASS

PASS

7

Adjacent Chan

nel Leakage Po

wer Ratio (ACL

R)

ACLR Offset +5/-5M

Hz Rel -32.2dBc ↓ Normal, Temp L, Te

mp H Low, Mid,

High PASS

PASS

ACLR Offset +10/-10

MHz Rel -42.2dBc ↓ Normal, Temp L, Te

mp H Low, Mid,

High PASS

PASS

8 Error Vector M

agnitude(EVM)

EVM at Tx output po

wer 24dBm /-18dBm 17.5% ↓ Normal Low, Mid,

High PASS

PASS

9 Peak code do

main error PCDE at Tx output p

ower 24dBm/-18dBm

-14dB ↓ Normal Low, Mid,

High PASS

PASS

10 Phase Disconti

nuity

Phase Discontinuity

max EVM 17.5% ↓

Normal Mid

- PASS

-

Phase Discontinuity

max Frequency Error

-195~195Hz - PASS

-

Phase Discontinuity

max 1500Hz 36 degrees ↓ - PASS

-

11 Reference Sen

sitivity Level

Ref Sense Go/No Go

I^or=-104dBm/3.84M

Hz BER 0.1% ↓ Normal, Temp L, Te

mp H Low, Mid,

High PASS

PASS

12 Maximum Inpu

t Level

Max Input Go/No Go

I^or=-25.7dBm/3.84M

Hz BER 0.1% ↓ Normal Mid - PASS

-

8. Connectors

8.1 Antenna connector : 59S21B-40MT5_D (Vendor : Rosenberger)

8. Connectors

8.2 40-pin Connector : 12709HS-H40 (Vendor : YUNHO)

9. RFx information

The strength of the RF field produced by the wireless module or modules

embedded in the TCU is well within all international RF exposure limits known

at this time. Because the wireless modules embedded in the TCU emit less than

the maximum amount of energy permitted in radio frequency safety standards

and recommendations, the manufacturer believes these modules are safe for

use.

Regardless of the power levels, care should be taken to minimize human

contact during normal operation. This module should be remain more than 20

cm (8 inches) from the body when wireless devices are on and transmitting.

This transmitter must not be collocated or operated in conjunction with any

other antenna or transmitter. Operation is subject to the following two conditions:

(1) this module does not cause interference , (2) this module accepts any

interference that may cause undesired operation.

9.1 Information for the integrator

The integrator must not provide information to the end user regarding how to

install or remove this RF module in the user manual of the end product. The user

manual that is provided by the integrator for end users must include the following

information in a prominent location. To comply with FCC RF exposure

requirements, the antenna used for this transmitter must be installed to provide a

separation distance of at least 20 cm from all persons and must not be

collocated or operated in conjunction with any other antenna or transmitter. The

label for the end product must include FCC ID: YZP-BH1000 or A RF transmitter

inside, IC ID: 7414C-BH1000

10. Approbation FCC

This module complies with FCC/IC regulations.

FCC: Part 22, Part 24

IC: RSS-132, RSS-133

Furthermore, this device complies with FCC/IC radiation exposure limits set forth

for uncontrolled environments.

This module must be installed and operated with minimum distance of 20 cm

between the radiating element and the user.

This module must not be co-located with any other transmitters or antennas.

To comply with FCC/IC regulations limiting both the maximum RF output power

and human exposure to RF radiation, the maximum antenna gain including

cable loss in a mobile-only exposure condition must not exceed the values listed

in the following table.

To satisfy the exterior labeling requirements, the following text must appear on

the exterior of the end product.

Contains transmitter module FCC ID: YZP-BH1000

Contains transmitter module IC: 7414C-BH1000

Changes or modifications to this equipment may cause harmful interference

unless the modifications are expressly approved in the instruction manual. Users

may lose the authority to operate this equipment if an unauthorized change or

codification is made.

Note: If this module is intended for use in a portable device, additional testing

will be required to satisfy the SAR requirements of FCC Part 2.1093 and RSS-

102.

Band Frequncy Range [MHz] Maximum Antenna

Gain[dBi]

WCDMA(B5) 826.4 ~ 846.6 5.60

WCDMA(B2) 1852.4 ~ 1907.6 7.50

Guide de l'utilisateur pour le LTD-BH1000

1. Vue d'ensemble

2. Principales caractéristiques

3. Interface

4. Spécifications électriques

5. Spécifications RF

6. Spécifications mécaniques

7. Spécifications générales

8. Connecteurs

9. RFx information

10. Approbation FCC

Table des matières

Produit: Modem sans fil WCDMA

Nom du modèle: LTD-BH1000

Le LTD-BH1000 est un appareil de communication mobile qui intègre les plus

récentes technologies de radio, incluant les éléments les plus petits et les plus

légers ainsi que le soutien pour les bandes WCDMA (accès multiple à large

bande par partage de code)(850/1900MHz). Ce dispositif agit en tant que

système télématique du véhicule et se connecte au WCDMA (HSPA +) des

réseaux sans fil et des modules sans fil pour permettre les communications voix

et données. En outre, ce dispositif peut fonctionner sur terre et sur l'eau ainsi que

d'autres zones similaires.

En mode HSPA+, le dispositif fournit des vitesses en liaisons montantes jusqu'à

5,76 Mo/s et des vitesses en liaisons descendantes jusqu'à 14,4 Mo/s pour un

transfert rapide de données comme des films et des appels vidéo. Le dispositif

permet également le transfert de volumes importants de données.

Le dispositif communique avec le système hôte au moyen du standard RS-232

ou du port USB, et les commandes AT ainsi que les commandes de contrôles

peuvent être utilisées pour transmettre des données. Les communications

téléphoniques sont également possibles.

1. Vue d'ensemble

La page charge ...

LG Innotek YZP-BH1000 Manuel utilisateur

Ce manuel convient également à

LG Innotek YZP-BH1000 Manuel utilisateur

dans d''autres langues

Autres documents