Red Sea ReefATO+ Le manuel du propriétaire

ReefATO+

ENG | DE | FR

User Manual

Red Sea ReefATO+

3

ENG

User Manual

Smart ATO – Temperature Sensor – Leak Detector

ReefATO+

Red Sea ReefATO+

4

Red Sea ReefATO+

5

ENG

Contents

Introduction ................................................................................6

Safety ..........................................................................................7

Components of the ReefATO+ system ..................................... 8

Guide to the ReefATO+ Controller ............................................9

How the ReefATO+ Auto-Fill system works ..........................11

Introduction to the ReefBeat app ..........................................12

Installing the ReefATO+ system .............................................12

Setting up the ReefATO+ .........................................................16

Device Maintenance ................................................................ 20

Troubleshooting .......................................................................21

Warranty ...................................................................................22

Red Sea ReefATO+

6

Introduction

Congratulations on your purchase of Red Sea’s 3-in-1 ReefATO+ smart

Reef Aquarium ATO system, plus temperature monitor and leak detector.

The ReefATO+ is designed to maintain a stable salinity and water volume

in a reef aquarium by automatically replenishing the water lost due to

evaporation.

The ReefATO+ consists of a slim-line, multi-input, solid-state water level

sensor, bespoke DC pump, wi-fi connected controller and a complete set

of accessories required to install the system. In addition, the ReefATO+

provides two other critical aquarium health indicators; a fully featured

on-line digital temperature monitor that is embedded in the level sensor

and an external leak detector.

The ReefATO+ is part of Red Sea’s suite of smart devices that are

operated via Wi-Fi by Red Sea’s ReefBeat® App, which needs to be

installed on a smart mobile device with internet connectivity.

Welcome to Red Sea’s smart reef-keeping.

The Red Sea Team

Red Sea ReefATO+

7

ENG

Safety

PLEASE READ AND FOLLOW ALL SAFETY INSTRUCTIONS

THIS DEVICE IS INTENDED FOR INDOOR USE ONLY.

DANGER: To avoid possible electric shock, special care should be taken

when handling a wet aquarium. For each of the following

situations, do not attempt repairs yourself; return the appliance

to an authorized service facility for service or discard the

appliance.

WARNING: To guard against injury, basic safety precautions should be

observed, including the following:

Do not operate any appliance if it has a damaged cord or plug, if it is

malfunctioning, or if it is dropped or damaged in any manner.

This appliance can be used by children aged from 8 years and above and

persons with reduced physical, sensory, or mental capabilities or lack

of experience and knowledge if they have been given supervision or

instruction concerning use of the appliance in a safe way and

understand the hazards involved. Children shall not play with the

appliance. Cleaning and user maintenance shall not be made by children

without supervision.

The appliance is only to be used

with the power supply unit

provided with the appliance.

Close supervision is necessary

when any appliance is used by

or near children.

To avoid injury, do not contact

moving parts.

Always unplug an appliance

from an outlet when not in use, before putting on or taking off parts, and

before cleaning. Never pull the cord itself to remove the plug from the

outlet. Grasp the plug and pull to disconnect.

Do not use an appliance for anything other than its intended use.

The use of attachments not recommended or sold by the appliance

manufacturer may cause unsafe conditions.

Do not install or store the appliance where it will be exposed to the

weather or to temperatures below freezing point.

Make sure an appliance is securely installed before operating it.

Read and observe all the important notices on the appliance.

Note: A cord rated for less amperes or watts than the appliance rating

may overheat. Care should be taken to arrange the cord so that

it cannot be tripped over or pulled accidentally.

Do not use if cord is damaged. In case of need, do not attempt

to replace or repair yourself; return the appliance to an

authorized service facility for service or discard the appliance.

In case of need, do not attempt to replace yourself; return the

appliance to an authorized service facility for service or discard

the appliance.

Red Sea ReefATO+

8

Components of the ReefATO+ system

R35623

ATO sensor magnetic corner mounting bracket

(not included with the ReefATO+ kit for Reefer Aquariums)

R35625

ReefATO+

Corner Bracket

Magnets

(not included with the

ReefATO+ kit for

Reefer Aquariums)

R35628

Leak Detector

R35626

Silicone Tubing

R35627

Syphon Breaker

R35621

ATO

Pump

R35624

Tube Holder

R35620

ReefBeat

Connected

ATO+ controller

R35629

Sensor holder

R35622

ATO Level &

Temperature

Sensor

Red Sea ReefATO+

9

ENG

Guide to the ReefATO+ Controller

Settings

Indicator LED

Leak Detector

Status LED

ATO Sensor

Status LED

ATO Pump

Status LED

Power

Status LED Leak Detector

Port

ATO Sensor

Port

ATO Pump

Port

DC inlet

Port

Settings Button

Manual Pump

Button

Red Sea ReefATO+

10

LED Indicators

Settings LED Indicator:

• Solid Red light – Controller is connected to the home-network.

• Blinking Red light – Controller is in Wi-Fi Access Point (AP) mode (can

be discovered by Wi-Fi devices).

• Rapid Blinking Red light – Controller cannot access the home-network

(network name and/or password are incorrect or known network has

become unavailable)

• No Red light – Controller Wi-Fi is off.

• Double blink – indicates change of status / end of process.

Leak Detector Status LED Indicator:

• Solid Red light –Leak detection is enabled

• No Red light – Leak detection is disabled

• Blinking Red light – Leak has been detected and Auto-Fill has been

disabled

ATO Sensor Status LED Indicator:

• Solid Red light –Auto-Fill is enabled

• No Red light –Auto-Fill is disabled

• Blinking Red light – ATO Sensor is missing

Pump Statu¬s LED Indicator:

• Solid Red light – Pump is on.

• No Red light – Pump is off.

• Blinking Red light – Pump malfunction (missing, stalled, or running

dry)

Power LED Indicator:

• Solid Red light –PSU is attached.

• No Red light –PSU is not attached.

Settings Button – Function

If settings indicator LED is off (ReefATO+ Controller Wi-Fi is off): Pressing

button for 5 seconds (until double blink) activates Wi-Fi AP mode.

If settings indicator LED is blinking (ReefATO+ Controller Wi-Fi is in AP

mode): Pressing button for 5 seconds (until double blink) switches Wi-Fi

off.

If indicator LED is on (ReefATO+ Controller Wi-Fi is connected to a Wi-Fi

network): Pressing button for 5 seconds (until double blink) disconnects

the ReefATO+ from the network and switches it to Wi-Fi AP mode. (Note:

before disconnecting a ReefATO+ from a network, delete it from the

ReefBeat App via the Device Manager.) Note: All settings are retained

and can be restored when reconnecting to the ReefBeat.

Reboot: Pressing and releasing the button for less than 2 seconds will

cause the unit to shut down and restart. User settings are not affected.

Clear Settings: Pressing the button for 15 seconds (until double blink)

deletes all user settings and switches the Wi-Fi to AP mode. Complete

the reset process by disconnecting and reconnecting the DC power.

Manual Pump Button - Function

Pressing on the manual pump button will operate the pump for as

long as it is pressed. The pump status LED will be on while the pump is

running. In the event that the Auto-fill has been automatically disabled

by the controller (such as if the RO reservoir has run out of water) a

short press on pump button will reinstate the Auto-fill function.

Red Sea ReefATO+

11

ENG

How the ReefATO+ Auto-Fill system works

During regular operation when Auto-

Fill is enabled, the water level will be

maintained within the 3mm / 1/8”

band between the pump-on and pump-

off probes of the ATO sensor. As soon

as the water level drops to the bottom

of the “pump-on” probe, the ATO pump

will automatically switch on and will

continue pumping water from the RO

reservoir until the water level rises to

the “pump-off” probe, at which time the

pump will automatically switch off.

In the unlikely event that the “pump-off” probe does not sense the rise

of the water level there are backup “pump-off” probes located approx.

2.5cm / 1” above the regular “pump-off” probe.

As an additional safety feature, there is an automatic pump timeout

feature that will switch the pump off if it runs for significantly longer

than the normal fill time for your system.

The Auto-Fill will automatically switch off if any of the following

situations occur:

• Pump is missing, over-run timeout, running dry (empty reservoir) or

blocked.

• Level/temp sensor is missing.

• Leak detector detects a leak.

The full array of titanium probes also provides an on-line indication if the

water level is above, below or at the desired level.

ReefATO+ Temperature monitor

The ATO level sensor includes an accurate digital thermometer that is

connected to the lower titanium probe enabling a quick response to

temperature changes. The thermometer has been pre-calibrated to

an accuracy of 0.1 degrees to ensure a reliable absolute temperature

reading at all times. The ReefBeat App allows you to set a desired range

and a wider acceptable range of temperatures for triggering notifications

and presents a full log for analysis. The ReefBeat also allows you to

offset the temperature reading to synchronize it with other temperature

monitors you may have on your system.

ReefATO+ Leak Detector

The ReefATO+ leak detector is highly sensitive and will detect the full

range of waters from RODI to seawater. When a leak is detected the ATO

Auto-fill is immediately disabled including switching off the ATO pump if

it was running. To avoid false alarms, the system waits a few seconds to

confirm that the leak persists and then sounds an audible alarm as well

as sending a notification to your mobile device. The ReefBeat App allows

you to connect the leak detector to the Emergency Quick-action function

in order to automatically shut down other ReefBeat devices such as

return pumps in case a leak is detected.

Backup

Pump Off

2.5cm / 1”

3mm / 1

/8”

Pump On

Temperature Probe

Red Sea ReefATO+

12

Introduction to the ReefBeat app

All Red Sea’s connected devices are operated via the ReefBeat app

which must be installed on a mobile device with an internet connection

(including tablets). See the full list of supported mobile devices on our

website.

Through your personal user account on the cloud, ReefBeat enables

you to set up and manage any number of aquariums and add multiple

devices to each of them.

For full functionality, the controller must have a permanent connection

to the internet through your home Wi-Fi network. In this mode of

operation, you will be able to see the current status of your ReefATO+,

change the settings or receive notifications on your mobile whenever

you have access to the internet.

The ReefBeat homepage will show you the current status of all your

connected devices, and links you directly to the Settings page of each

unit.

You can install ReefBeat on multiple mobile devices by entering the

same user account details. All mobile devices will have the same rights

for operating and changing all the settings. You should keep this in mind

before giving your user details to any 3rd party.

If you do not have a home network or your home network does not

have an active internet connection, you can connect and control your

ReefATO+ in Offline or Direct Mode. However, certain functionality such

as remote access, multiple mobile devices or status notifications will not

be available.

ReefBeat is constantly under development. For the most up to date

operation instructions, view or download the latest user guide from the

Red Sea website at www.redseafish.com

If this is your first Red Sea connected device, it is recommended that you

complete the physical installation of your ReefATO+ before installing the

ReefBeat app.

Installing the ReefATO+ system

Locate the ReefATO+ controller in a convenient position and attach the

mounting bracket using screws or the adhesive tape provided. The

controller is designed to operate in a humid environment but it is not

waterproof. Please take the appropriate precautions in choosing its

location and whenever removing the controller from the mounting

bracket.

When selecting the exact location for the controller consider the

following:

The power supply unit that is plugged into the rear of the controller and

the AC outlet has a 2m / 6.5’ cable.

The ATO pump that will be located in the RO reservoir has a 3m / 10’

cable that needs to be connected to the bottom of the controller.

The ATO sensor that should be located in the return pump chamber of

your sump has a 3m cable that needs to be connected to the bottom of

the controller.

The Leak detector should be located at a convenient point around the

outside of the aquarium and has a 3m / 10’ cable that needs to be

connected to the bottom of the controller.

The ATO sensor should be located in a corner of the return pump

chamber so that the desired water level is approximately between the

“pump on” and “pump off” pins. The water level will automatically

adjust to this level once it begins regular operation.

Red Sea ReefATO+

13

ENG

Click

Sensor holder installation for Red Sea sumps Sensor holder with magnetic corner bracket,

for non Red Sea sumps

Click

Sensor holder installation for Red Sea sumps Sensor holder with magnetic corner bracket,

for non Red Sea sumps

For Red Sea aquariums click the sensor holder onto the glass triangle

located in the return pump chamber. For older systems that have the

gravity fed float valve, remove the valve by unscrewing the nut that

holds it in place and then click the sensor holder onto the glass triangle.

For non-Red Sea sumps, attach the sensor holder to the magnetic corner

bracket that will ensure that the sensor is always vertical. The external

magnets are waterproof and can be mounted on internal walls of the

sump. Note: the magnets are very strong and care needs to be taken

when using them.

Slide the sensor into the sensor holder and click into the higher or lower

position as suitable for your system. Thread the cable of the sensor

through the cabinet and connect to the sensor port of the controller.

Red Sea ReefATO+

14

Pump

Chamber

Water Level

RO

Water

Level

Using the silicone tube provided, connect the water outlet of the ATO

pump to the tube holder that should be attached to the top rim of

the sump chamber where the sensor is located. To ensure a secure

connection make sure that the tube is cut straight and at 90 degrees

to the tube, push the tube over the hose-barb until it is touching the

securing nut and screw the nut counter-clockwise over the tube. The

outlet of the holder should be above the highest expected water level in

the sump and preferably not directly above the sensor. If the maximum

water level in the RO reservoir can be higher than the tube holder, install

the syphon breaker on the silicone tube so that it is below the rim of

the RO reservoir, but will always be above the water level. Note: water

will trickle from the syphon breaker back into the RO reservoir whenever

the pump is working. Secure the tube to each of the components using

the lock nuts provided and place the pump into the RO reservoir. Make a

note of the approximate length of tube used to connect the pump to the

tube holder and the vertical height from the bottom of the pump to the

outlet of the tube holder as you will need this information for the App.

For quiet operation and to utilize almost all of the available water, locate

the pump so that it is vertical and not touching the reservoir walls.

Thread the power cable of the pump through the cabinet and connect to

the pump port of the controller.

Red Sea ReefATO+

15

ENG

Locate the leak detector at a convenient point around the outside of the

aquarium and secure in position with the self-adhesive Velcro pads, or

with screws. Thread the cable of the leak detector through the cabinet

and connect to the leak detector port of the controller. Installation of

the leak detector is optional and will not affect the operation of the ATO

system if it is not installed.

When all preparations are complete, connect the power supply to the

DC jack on the rear of the controller and plug it into the AC wall outlet.

The power indicator LED will turn on to show that the power supply is

connected, pressing the manual button on the front of the controller will

operate the pump, however, the ATO system will not work automatically

until the controller has been onboarded to the ReefBeat App and the

Auto-fill enabled.

Follow the instruction below to onboard the

ReefATO+ controller to the ReefBeat App.

Connection and initial Setup

Download and install the ReefBeat-App from the app Store or Google

Play as appropriate for your Mobile Device. (In countries without

access to Google Play, an APK file and installation instructions can be

downloaded from Red Sea's website.)

After installing ReefBeat, you will be guided through the set-up of your

ReefBeat user account and aquariums, and then you can start adding

your Red Sea connected devices. All your user account details can be

edited, but only when your mobile is connected to the internet.

For full functionality, Red Sea's connected devices should be connected to

the internet and your aquariums should be set to "Online". If you do not

have an available Wi-Fi network at your Aquarium, set it as "Offline". You

can change this setting later when Wi-Fi becomes available.

Make sure that you select the correct world time zone for where your

aquarium is located. The default is the same time zone as your mobile

which might be set for a different location. There is also a "Daylight

saving Time" (DST) toggle that needs to be manually switched at the

beginning and end of DST for your location.

If you have set up more than one aquarium, select the aquarium from

the dropdown menu at the top of the screen before proceeding.

Set the controller to AP mode by pressing the settings button for 5

seconds (until double blink). The indicator LED should be blinking.

Tap the Add Device button from the Device Manager page, select the

icon for the ReefATO+ and follow the instructions in the app. This may

take a few seconds. If no devices appear on the list, check that the

controller is in AP mode and/or refresh the page.

ReefBeat-App will now display a list of Wi-Fi networks and signal

Red Sea ReefATO+

16

strengths that are available to the controller from its current location.

Select your preferred network and wait a few moments while the

controller connects to it. The indicator LED will now be a solid red. Follow

the instructions on the app for initial settings.

If you have set the aquarium to Offline, select the “Direct Mode” option

at the top of the screen to skip the network connection. The indicator LED

will continue to blink as the controller Wi-Fi remains in AP mode.

Follow the instructions in the app for connecting the controller to the

ReefBeat App and cloud.

If you already have the pump, sensor and leak detector connected to the

Controller follow the instructions in the App for setting them up.

Setting up the ReefATO+

ATO Auto-Fill

When setting up the system the App will ask for the length of tube used

to connect the pump to the tube holder and the height from the bottom

of the pump to outlet of the tube holder. These values can be modified

later from: Homepage > ATO Settings > more settings, the length cannot

be smaller than the height. These values are used to automatically set

the appropriate pump speed for your installation and estimate the flow

rate that will be used in the top-off log and reservoir volume monitor.

The flow rate is only an approximation, if you want a more accurate

record you can measure the actual flow rate for your system and

update the App: Homepage > ATO Settings > more settings > Flow rate

adjustment.

Each ATO level/temperature sensor has a 3-digit temperature calibration

code (between 400 & 600) that needs to be entered to the App. The

code can be found on a label attached to the sensor cable.

By default, the Auto-fill operation of the system is switched off to allow

you to ensure that the sensor is properly in place and that there is water

in the reservoir before it is activated.

When you are ready, toggle the Auto-fill - ON.

ATO Reservoir Volume Monitor

The “Reservoir Volume Monitor” automatically deducts the amount of

water used for each fill from the last updated reservoir volume that you

entered. The ReefBeat will present the current volume in the reservoir

and will let you know 24 hours before it is due to run out. Whenever

you refill the reservoir, you will need to enter the new volume, so if

you do not plan on maintaining this feature it is best not to enable it.

The Monitor is only an approximate indication and has no effect on the

operation of the auto-fill. The controller detects when the reservoir has

actually run out of water by monitoring pump performance and will

switch off the auto-fill until you refill the reservoir and “resume” it.

ATO Quick Action Return Delay

The ReefATO+ can be connected to the ReefBeat Maintenance/

Emergency Quick-Action buttons. All devices that are configured for

these Quick-Actions will immediately shut down when they are enabled

and will resume immediately when they are switched off.

To delay the restart of the Auto-fill, set the Return Delay to the desired

number of minutes required for all other equipment to restart and water

levels in the sump to return to normal. Use this setting, for example, if

you want to check the water level in the sump after a water change to

allow the option to add some more salt water instead of having the ATO

automatically add RO water.

Red Sea ReefATO+

17

ENG

Temperature monitor - Notification ranges

The ReefATO+ homepage presents the current temperature and a green/

amber/red status indicator according to the desired and acceptable

temperature ranges that you define for your system. If the temperature

goes above or below the acceptable range you will get a notification

to your mobile device. To set the temperature ranges: Homepage >

Temperature Settings > Temperature ranges

Temperature monitor – Synchronize with another thermometer

The ReefBeat enables you to offset the presented temperature value

to synchronize with another thermometer on your system. Note that

most digital thermometers are accurate to ±0.5 degrees. The ReefATO+

temperature can be restored to its default value at any time. After

setting the new temperature use the “Current temperature” button

to confirm that the temperature has updated correctly. Homepage >

Temperature Settings > Synchronize Temperature

Leak Detector – Settings

The ReefBeat enables you to easily enable/disable the leak detector the

audible buzzer alarm or connecting to the Emergency Quick-action of the

aquarium. Homepage > Leak Settings

ATO and Temperature Logs

The Top-off log is a detailed record of number of fills and calculated

volume of water that has been added to your aquarium for each day in

the last 28 days (7 days if the aquarium is in offline mode), which can

also be expanded to show the values per hour.

To view the log: Homepage > ATO Settings > Top-off Log

The Temperature log is a detailed record of minimum, maximum and

average temperatures recorded in your aquarium for each day in the last

28 days (7 days if the aquarium is in offline mode), which can also be

expanded to show the values in 15-minute intervals throughout each

day. To view the log: Homepage > Temperature Settings > Temp Log. If

you plan on removing the sensor from the sump for a period of time you

can avoid irrelevant temp readings from being recorded by temporarily

disabling the log Homepage > Temperature Settings > Update log.

Export a copy of the logs by clicking “Send” at the top of the page and

selecting your desired communication channel (Gmail, WhatsApp, FB

messenger, etc.). You should do this on a regular basis if you wish to

keep a record beyond the 28 days available from ReefBeat.

Operation

When the Auto-fill is enabled the ReefATO+ works independently unless

it runs into an issue that needs your attention such as the following:

• Pump is missing, over-run timeout, running dry (empty reservoir) or

blocked

• Level/temp sensor is missing

• Leak detector detects a leak

In all of the above cases, resolve the issue and resume the Auto-fill by

either:

A short press on the manual pump button on the controller.

Pressing on the “resume” button in the App: Homepage > ATO Settings

> Resume button.

Red Sea ReefATO+

18

Water changes or sump maintenance

Whenever you undertake any activity that will temporarily lower the

water level in the sump and/or cause water near the leak detector, you

should do one or more of the following to prevent the ReefATO+ from

automatically “topping-off” or setting off the leak alarm.

• Switching off the “Auto-fill” from the ATO settings page will

temporarily disable just this function

• Switching off the “Leak Detection” from the Leak settings page will

temporarily disable this function

• Temperature - "Disable Log" will prevent irrelevant data from being

recorded in the log

Switching OFF the ReefATO+ from the device manager will do all of the

above at once

If using any of the above, remember to switch the function back on after

maintenance is completed.

Connecting the ReefATO+ to the Maintenance shortcut will switch off all

of the functions together with other ReefBeat devices that are in your

sump.

When restarting after a water change it is recommended not to activate

the Auto-fill immediately and to wait until all devices that affect the

water level in the sump are fully operational. Use the “Check sump

water level” option (Homepage > ATO Settings > More settings) to check

that the water level is back to normal so that you can add/remove

saltwater as required. If the water level is below the sensor you can

manually add more water from the reservoir by pressing the button on

the controller while periodically pressing the “GO” button to update the

on-screen display of the water level.

ReefBeat Device Manager

The Device Manager is accessible from the Page menu in both the

ReefBeat homepage and the device settings page, and contains a list of

all the Red Sea connected devices that are installed on each aquarium.

The devices are listed according to type and in the order in which they

were added to the aquarium. Tapping the 3-dot menu for the individual

device opens a list of available actions for the specific device. Tapping

the 3-dot menu for the device type opens a list of actions that can be

done simultaneously for all devices of the same type.

Turn OFF / Turn ON

The device can temporarily be turned off/on without physically

unplugging it or losing any of its settings.

For individual units: Device manager > Device line menu > Turn OFF / ON.

For device type: Device manager > Device type menu > Turn OFF / ON

Reconnecting a device to the ReefBeat Cloud

If you have received a disconnected notification for your device, it may

need a reboot to reconnect it.

If the settings indicator LED on the device is ON click the Reboot button

from the device manager: Device Manager > Device Line menu > Reboot.

If the settings indicator LED is OFF pressing the settings button on the

device for less than 2 seconds will initiate the Reboot enabling the

device to reconnect to the home network. If this does not resolve the

issue, check that the network is available.

Red Sea ReefATO+

19

ENG

Firmware Updates

From time to time, you may receive a notification that a new firmware

version is available for your device. It is important to keep your device

firmware updated to ensure compatibility with updates to the ReefBeat

App.

Individual units can be updated: Device manager > Device line menu >

Firmware Update.

To update all units simultaneously: Device manager > Device type menu

> Firmware update

Do not unplug a device while it is downloading and installing the new

firmware.

Device Manager > Device Line menu > About - will show the currently

installed firmware version. When the firmware update is complete, the

“About” page will show the new version as the current version along

with the date and time that the update was performed. All your previous

settings will remain as before. If the firmware update is not successful,

the device will automatically revert to the previous version. Repeat the

process a few minutes later.

If your device does not seem to be performing correctly after the update,

reboot the unit by pressing the settings button for less than 2 seconds.

Deleting a device

To remove a device from an aquarium, delete the unit from the ReefBeat

App:

Device Manager > Device Line menu > Delete.

Deleting the device before it is switched off will prevent unnecessary

notifications that it is disconnected from the cloud.

Clear settings

To permanently remove all user settings from the memory of the

ReefMat and return it to its initial default state, perform the following

steps.

If the device is connected to the ReefBeat, trigger the hard-reset option

from the Device-Manager: Device Manager> Device line menu > Hard-

Reset

If the device is not connected to the ReefBeat, press the Settings button

for about 15 seconds (until the Wi-Fi indicator LED shows a double blink),

release the button and wait for about 1 minute for the device to reboot.

The unit will restart without any user settings and with the Wi-Fi

switched on, exactly as shipped from the factory. The unit will retain the

latest installed version of the firmware.

Red Sea ReefATO+

20

Device Maintenance

Controller

For continued smooth running of the controller, we recommended

making sure that it is kept clean, dry, and free of any buildup of salt

deposits on a regular basis.

The unit is not waterproof. Do not submerge in water or other solutions.

ATO level/temperature sensor

Make sure that the sensor is kept free of any build-up of organic

waste, algae growth, or salt deposits on a regular basis. The sensor is

waterproof and can be safely washed under running water. The titanium

tips can be brushed to remove any hard deposits.

It is recommended to wipe the sensor pins to remove build-up about

once per month.

Switch off the Auto-fill before removing the sensor for maintenance.

If the sensor holder is not easily viewable, after returning the sensor use

the “Check sump water level” to ensure that it is in the correct position.

Pump impellors

Remove the impellor chamber cover about once a month to ensure

that the impellor chamber

is free of any particulate

matter. If necessary, the

impellor can be removed

for maintenance by

inserting the point of

a tweezer in the gap

between the impellor and

impellor shaft, rotate and

pull outwards.

To replace the impellor, align the flat part of the impellor shaft with the

impellor and push down until it clicks into position.

Leak Detector

Check the functionality of the leak detector about once per month by

putting the pins in water. Make sure the pins are properly dry after the

test and that you “resume” the Auto-fill.

Measuring actual pump flow rate

The actual flow rate of the pump is calculated by measuring the volume

of water that is pumped in a known amount of time. Before starting,

make sure that the App is set to the correct length and height of the

silicone tube as these inputs affect the pump speed setting. Use a

collection vessel with a volume of about 1 liter and run the pump for

15 seconds. Depending on the length of the tube, it may take a few

seconds after starting the pump for the water to start flowing out the

end of the tube. Start the pump running from the App and hold the end

of the tube at approximately the same height as in normal operation.

Once the water is flowing, collect water for 15 seconds and switch the

pump off. In most setups the volume will be approximately 300 ml but

could range from 75 to 750. Multiplying the volume by 4 will give the

flow rate in ml/minute which should be entered in the App. Using a

kitchen scale in grams and weighing the collection vessel before and

after collecting the 15 second sample will give a more accurate result

(1 g of water equals 1 ml). For increased accuracy, repeat about 3 times

and use the average. The default estimated flow rate can be reinstated

from the App at any time.

AB C

La page charge ...

Red Sea ReefATO+ Le manuel du propriétaire

Red Sea ReefATO+ Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents