Continental Fireplaces CBL46NT Manuel utilisateur

Marque: Continental Fireplaces

Modèle: CBL46NT

Catégorie: Cheminées

Taper: Manuel utilisateur

FRENCH PG. 25

W415-3085 / A / 02.28.22

For indoor use only

FIRE OR EXPLOSION HAZARD

Failure to follow safety warnings exactly could result in serious injury, death, or property damage.

SAFETY INFORMATION

- Do not store or use gasoline or other ammable vapors and liquids in the vicinity of this or any other

appliance.

WHAT TO DO IF YOU SMELL GAS:

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in your building.

• Leave the building immediately.

• Immediately call your gas supplier from a neighbour’s phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the re department.

- Installation and service must be performed by a qualiﬁed installer, service agency, or the supplier.

WARNING

$10.00

OWNER’S MANUAL

Linear Series

(CBL46 with optional surround illustrated)

ENGLISH

W415-3085 / A / 02.28.22

safety information

• This appliance is hot when operated and can cause

severe burns if contacted.

• Any changes to this appliance or its control can be

dangerous and are prohibited.

• Do not operate appliance before reading and

understanding operating instructions. Failure

to operate appliance according to operating

instructions could cause ﬁ re or injury.

• Risk of ﬁ re or asphyxiation do not operate appliance

with ﬁ xed glass removed.

• Do not connect 110 volts to the control valve.

• Risk of burns. The appliance should be turned off

and cooled before servicing.

• Do not install damaged, incomplete or substitute

components.

• Risk of cuts and abrasions. Wear protective gloves

and safety glasses during installation. Sheet metal

edges may be sharp.

• Children and adults should be alerted to the

hazards of high surface temperature and should

stay away to avoid burns or clothing ignition.

• Young children should be carefully supervised

when they are in the same room as the appliance.

Toddlers, young children, and others may be

susceptible to accidental contact burns. A

physical barrier is recommended if there are at

risk individuals in the house. To restrict access to

an appliance or stove, install an adjustable safety

gate to keep toddlers, young children and other at

risk individuals out of the room and away from hot

surfaces.

• Clothing or other ﬂ ammable material should not be

placed on or near the appliance.

• Due to high temperatures, the appliance should be

located out of trafﬁ c and away from furniture and

draperies.

• Ensure you have incorporated adequate safety

measure to protect infants/toddlers from touching

hot surfaces.

• Even after the appliance is out, the glass and/or

screen will remain hot for an extended period of

time.

• Check with your local hearth specialty dealer

for safety screens and hearth guards to protect

children from hot surfaces. These screens and

guards must be fastened to the ﬂ oor.

• Any safety screen, guard or barrier removed for

servicing the appliance, must be replaced prior to

operating the appliance.

• The appliance is a vented gas-ﬁ red appliance. Do

not burn wood or other materials in the appliance.

• The appliance area must be kept clear and free

from combustible materials, gasoline and other

ﬂ ammable vapors and liquids.

3.1

WARNING

• Under no circumstances should this appliance be

modiﬁ ed.

• This appliance must not be connected to a chimney

ﬂ ue pipe serving a separate solid fuel burning

appliance.

• Do not use this appliance if any part has been

under water. Immediately call a qualiﬁ ed service

technician to inspect the appliance and to replace

any part of the control system and any gas control

which has been under water.

• Do not operate the appliance with the glass door

removed, cracked or broken. Replacement of the

glass should be done by a licensed or qualiﬁ ed

service person.

• Do not strike or slam shut the appliance glass door.

• When equipped with pressure relief doors, they

must be kept closed while the appliance is

operating to prevent exhaust fumes containing

carbon monoxide, from entering into the home.

Temperatures of the exhaust escaping through

these openings can also cause the surrounding

combustible materials to overheat and catch ﬁ re.

• Only doors / optional fronts certiﬁ ed with the unit

are to be installed on the appliance.

• Keep the packaging material out of reach of

children and dispose of the material in a safe

manner. As with all plastic bags, these are not toys

and should be kept away from children and infants.

• As with any combustion appliance, we recommend

having your appliance regularly inspected and

serviced as well as having a carbon monoxide

detector installed in the same area to defend you

and your family against carbon monoxide.

• Ensure clearances to combustibles are maintained

when building a mantel or shelves above the

appliance. Elevated temperatures on the wall or

in the air above the appliance can cause melting,

discolouration or damage to decorations, a T.V. or

other electronic components.

• A barrier designed to reduce the risk of burns from

the hot viewing glass is provided with this appliance

and shall be installed.

• If the barrier becomes damaged, the barrier shall

be replaced with the manufacturer’s barrier for this

appliance.

• Installation and repair should be done by a qualiﬁ ed

service person. The appliance should be inspected

before use and at least annually by a professional

service person. More frequent cleaning may be

required due to excessive lint from carpeting,

bedding material, etc. It is imperative that control

compartments, burners and circulating air

passageways of the appliance be kept clean.

WARNING:

Electric

This product can expose you to chemicals including lead and lead

Gas, Wood

Mantels (including Firebox)

Accessories / Metal

Accessories / Brick

Accessories / Powder Coat

Fibre

compounds, which are known to the State of California to cause cancer, and chemicals includ-

ing BBP and DEHP, which are known to the State of California to cause birth defects or other

reproductive harm. For more information, go to www.P65Warnings.ca.gov.

AVERTISSEMENT:

Ce produit peut vous exposer à des substances chimiques incluant le

plomb et les composés de plomb qui, selon l’État de Californie, causeraient le cancer, et des

substances chimiques incluant le BBP et DEHP qui, selon d’État de Californie, causeraient des

malformations congénitales ou autres dangers pour la reproduction.

Pour de plus amples renseignements, visitez le www.P65Warnings.ca.gov.

WARNING:

This product can expose you to chemicals including lead and lead compounds,

which are known to the State of California to cause cancer, and chemicals including carbon

monoxide, which are known to the State of California to cause birth defects or other reproduc-

tive harm. For more information, go to www.P65Warnings.ca.gov.

AVERTISSEMENT:

Ce produit peut vous exposer à des substances chimiques incluant le

plomb et les composés de plomb qui, selon l’État de Californie, causeraient le cancer, et des

substances chimiques incluant le monoxyde de carbone qui, selon d’État de Californie, cause-

raient des malformations congénitales ou autres dangers pour la reproduction.

Pour de plus amples renseignements, visitez le www.P65Warnings.ca.gov.

WARNING:

This product can expose you to chemicals including wood dust, which are

known to the State of California to cause cancer, and chemicals including BBP and DEHP,

which are known to the State of California to cause birth defects or other reproductive harm.

For more information, go to www.P65Warnings.ca.gov.

AVERTISSEMENT:

Ce produit peut vous exposer à des substances chimiques incluant le

poussière de bois qui, selon l’État de Californie, causeraient le cancer, et des substances

chimiques incluant le BBP et DEHP qui, selon d’État de Californie, causeraient des malforma-

tions congénitales ou autres dangers pour la reproduction.

Pour de plus amples renseignements, visitez le www.P65Warnings.ca.gov.

WARNING:

This product can expose you to chemicals including chromium, which are

known to the State of California to cause cancer, and chemicals including toluene, which are

known to the State of California to cause birth defects or other reproductive harm.

For more information, go to www.P65Warnings.ca.gov.

AVERTISSEMENT:

Ce produit peut vous exposer à des substances chimiques incluant le

chrome qui, selon l’État de Californie, causeraient le cancer, et des substances chimiques

incluant le toluène qui, selon d’État de Californie, causeraient des malformations congénitales

ou autres dangers pour la reproduction.

Pour de plus amples renseignements, visitez le www.P65Warnings.ca.gov.

WARNING:

This product can expose you to chemicals including silica, which are

known to the State of California to cause cancer.

For more information, go to www.P65Warnings.ca.gov.

AVERTISSEMENT:

Ce produit peut vous exposer à des substances chimiques incluant le

silice qui, selon l’État de Californie, causeraient le cancer.

Pour de plus amples renseignements, visitez le www.P65Warnings.ca.gov.

WARNING:

This product can expose you to chemicals including titanium dioxide, which

are known to the State of California to cause cancer, and chemicals including toluene, which

are known to the State of California to cause birth defects or other reproductive harm.

For more information, go to www.P65Warnings.ca.gov.

AVERTISSEMENT:

Ce produit peut vous exposer à des substances chimiques incluant le

dioxyde de titane qui, selon l’État de Californie, causeraient le cancer, et des substances

chimiques incluant le toluène qui, selon d’État de Californie, causeraient des malformations

congénitales ou autres dangers pour la reproduction.

Pour de plus amples renseignements, visitez le www.P65Warnings.ca.gov.

WARNING:

This product can expose you to chemicals including silica, which are known to

the State of California to cause cancer, and chemicals including toluene, which are known to

the State of California to cause birth defects or other reproductive harm.

For more information, go to www.P65Warnings.ca.gov.

AVERTISSEMENT:

silice qui, selon l’État de Californie, causeraient le cancer, et des substances chimiques

incluant le toluène qui, selon d’État de Californie, causeraient des malformations congénitales

ou autres dangers pour la reproduction.

Pour de plus amples renseignements, visitez le www.P65Warnings.ca.gov.

Ce produit peut vous exposer à des substances chimiques incluant le

ADVERTENCIA:

Este producto puede exponerlo a productos químicos, entre ellos, plomo

y compuestos con plomo, que el Estado de California reconoce como causantes de cáncer, y

productos químicos, entre ellos, bencilbutilftalato (BBP, por sus siglas en inglés) y di(2-etilhex-

il) ftalato (DEHP, por sus siglas en inglés), que el Estado de California reconoce como caus-

antes de malformaciones congénitas u otros daños para la reproducción. Para obtener más

información, visite www.P65Warnings.ca.gov.

ADVERTENCIA:

Este producto puede exponerlo a productos químicos, entre ellos, polvo

de madera, que el Estado de California reconoce como causantes de cáncer, y productos

químicos, entre ellos, bencilbutilftalato (BBP, por sus siglas en inglés) y di(2-etilhexil) ftalato

(DEHP, por sus siglas en inglés), que el Estado de California reconoce como causantes de

malformaciones congénitas u otros daños para la reproducción. Para obtener más infor-

mación, visite www.P65Warnings.ca.gov.

W415-3085 / A / 02.28.22 3

table of contents

1.0 getting to know your appliance 5

1.1 control access 6

1.2 rating plate information 6

2.0 operating your appliance 7

2.1 using your appliance 7

2.2 on/off components 7

2.3 operating and lighting instructions 8

2.3.1 turndown 9

3.0 remote control layout 10

3.1 general transmitter layout 10

3.2 temperature display 10

3.3 in the event of a battery failure 11

3.4 low battery 11

4.0 clearances around fireplace 12

4.1 optional heat management system 13

4.2 clearances around appliance (TV and valuable objects) 14

5.0 maintenance 16

5.1 care of glass 16

5.2 care of plated parts 17

5.3 safety barrier removal 17

5.4 door trim removal 18

5.5 ﬁrebox glass door removal 18

6.0 replacement parts 19

7.0 accessories 20

8.0 troubleshooting 21

9.0 warranty 22

10.0 service history 23

This owner’s manual is written for a complete series of ﬁreplaces that have a variety of different features and speci-

ﬁcations. Before reading this manual, be sure you know which model of ﬁreplace that you have. This information

will have been ﬁlled out by the installer on the following page and on the rating plate that is permanently attached

to the ﬁreplace (see “rating plate information” section).

This manual is for the:

• CBL36-1 and CBL46 models

If required, more detailed technical information is included in the ﬁreplace installation manual.

The information throughout this manual is believed to be correct at the time of printing. Wolf Steel Ltd. reserves

the right to change or modify any information within this manual at any time without notice. Changes, other than

editorial, are denoted by a vertical line in the margin.

Visit the Continental website for the most current version of your appliance’s manual.

W415-3085 / A / 02.28.22

welcome

Dealer Information

Name of Dealer:

Dealer Location:

Dealer Phone:

Dealer E-mail:

Customer:

Customer Address:

Date of Installation:

Location of the appliance:

Installer:

Continental is proudly committed to your total home comfort. We are proud to say that our products continunously

surpass industry standards and our inspiration is you! More than anything, we want you to feel conﬁdent in

choosing Continental for your home. Our products are designed to provide that conﬁdence and ensure that every

Continental product is beyond compare.

Continental products are designed with superior components and materials assembled by trained craftsmen who

take great pride in their work.

A barrier designed to reduce the risk of burns from the hot viewing glass is provided with the appliance for your

safety. This barrier must be installed.

Your Continental ﬁreplace has been thoroughly inspected by a qualiﬁed technician before packaging to ensure that

you, the customer, receives the quality product that you expect from Continental.

Dealer : Fill in your dealer information (or business card) and the appliance installation information

below.

congratulations

Model:

Serial Number:

Dealer: Business card location

Natural Gas: CBL36NT-1

CBL46NT

Propane: CBL36PT-1

CBL46PT

W415-3085 / A / 02.28.22 5

getting to know your appliance

1.0 getting to know your appliance

Burner

Pilot

Safety barrier Glass door

Door trim Valve /

rating plate

/ lighting

instructions /

battery back

Some features and locations may vary depending on the model.

note:

LA VITRE CHAUDE CAUSERA DES

BRÛLURES.

NE PAS TOUCHER LA VITRE

AVANT QU’ELLE AIT REFROIDI.

NE JAMAIS LAISSER LES ENFANTS

TOUCHER LA VITRE.

HOT GLASS WILL CAUSE BURNS.

DO NOT TOUCH GLASS UNTIL

COOLED.

NEVER ALLOW CHILDREN TO

TOUCH GLASS.

DANGER

AVERTISSEMENT

A barrier designed to reduce the risk of burns from

the hot viewing glass is provided with this appliance

and shall be installed for the protection of children

and other at-risk individuals.

Une barriére conçu à réduire le risque de brûlures

causées par le verre chaud est fourni avec l’appareil

et sera installé pour la protection des enfants et

d’autres personnes à risque.

LA VITRE CHAUDE CAUSERA

DES BRÛLURES.

NE PAS TOUCHER LA VITRE

AVANT QU’ELLE AIT REFROIDI.

NE JAMAIS LAISSER LES

ENFANTS TOUCHER LA VITRE.

HOT GLASS WILL CAUSE

BURNS.

DO NOT TOUCH GLASS UNTIL

COOLED.

NEVER ALLOW CHILDREN TO

TOUCH GLASS.

WARNING

AVERTISSEMENT

The area above the ﬁreplace opening including the safety barrier, barrier frame and

the surface of the wall can get very hot during operation and should never be touched

until the appliance is off and completely cooled.

W415-3085 / A / 02.28.22

getting to know your appliance

Access to the control can be done by removing the safety barrier, door trim and control cover (see “maintenance”

section for instructions on how to remove these components).

1.1 control access

FLAME

ADJUSTMENT

This illustration is for reference only. Refer to the rating plate on the appliance for accurate information.

1.2 rating plate information

The rating plate must remain with the appliance at all times. It must not be removed.

note:

Certiﬁed to Canadian and American National Standards: CSA 2.22-XXXX / ANSI Z21.50-XXXX for Vented Decorative Gas Appliances

Certiﬁé selon les normes Nationales Canadiennes et Américaines: CSA 2.22-XXXX / ANSI Z21.50-XXXX pour les Appareils à gaz décoratif à évacuation

Direct vent, vented gas ﬁreplaces. Approved for bedroom, bathroom and bed-sitting room installation. Suitable for mobile home installation, if installed in accordance with the current

standard CAN / CSA Z240MH Series gas equipped mobile homes in Canada, or, in the United States, the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part

3280. When this US Standard is not applicable, use the Standard for Fire Safety Criteria for Manufactured Home Installations, Sites and Communities, ANSI / NFPA 501A. This appliance

must be installed in accordance with local codes, if any; if none, follow the current ANSI Z223.1 or CSA B149. For use with barrier WXXX-XXXX. Follow installation instructions.

Foyer à gaz ventilé. Homologué pour installation dans une chambre à coucher, une salle de bain et un studio. Approprié pour installation dans une maison mobile si son installation

conforme aux exigences de la norme CAN / CSA Z240MH Séries de maisons mobile équipées au gaz en vigueur au Canada, ou, aux États-Unis selon la norme 24 CFR, Part 3280,

Manufactured Home Construction and Safety Standard. Dans le cas ou cette norme d’États-Unis n’est pas pertinentes, utiliser la norme NFPA 501A, Fire Safety Criteria for Manufactured

Home Installations, Sites and Communities. Installer l’appareil selon les codes ou règlements locaux ou, en l’absence de tels règlements, selon les codes d’installation ANSI Z223.1 ou

CSA B149 en vigueur. Utiliser uniquement avec l’écran WXXX-XXXX. Suivre les instructions d’installation.

9700539 (WSL) 4001658 (NAC) 4001657 (NGZ) 4001659 (WUSA)

WOLF STEEL LTD. 24 Napoleon Road, Barrie, ON, L4M 0G8 Canada

XXXX XXXX XXXX XXXX

MODEL / MODÈLE

Altitude

Input

Reduced Input

Élévation

Alimentation

Alimentation Réduite

Manifold Pressure: 3.5” w.c. (NG)

Minimum Supply Pressure: 4.5” w.c. (NG)

Maximum Supply Pressure: 7”* w.c. (NG)

Pression au Collecteur: 3,5” d’une colonne d’eau (GN)

Pression d’Alimentation Min.: 4,5” d’une colonne d’eau (GN)

Pression d’Alimentation Max.: 7” ** d’une colonne d’eau (GN)

** Maximum inlet pressure not to exceed 13”.

Manifold Pressure: 10” w.c. (P)

Minimum Supply Pressure: 11” w.c. (P)

Maximum Supply Pressure: 13”* w.c. (P)

Pression au Collecteur: 10” d’une colonne d’eau (P)

Pression d’Alimentation Min.: 11” d’une colonne d’eau (P)

Pression d’Alimentation Max.: 13” * d’une colonne d’eau (P)

** Pression d’alimentation maximale ne devait pas dépasser 13”.

0-XXXXft (0-XXXXm)

Minimum clearance to combustible materials:

Top, sides & back: per standoff spacers for framing and ﬁnishing

materials. For non-combustible framing and ﬁnishing materials,

see installation manual.

Top X”

Floor X”

Sides X”

Back X”

Vent top X”

Vent sides & bottom X”

Recessed depth X”

*** Mantel X” from appliance opening

Dégagements minimaux des matériaux combustibles:

Dessus, côtés et arrière: selon les espaceurs de dégagements

pour les matériaux d’ossature selon le manuel du propriétaire

pour les matériaux de ﬁnition.

Dessus X”

Plancher X“

Côtés X”

Arrière X“

Dessus du conduit d’évent X”

Côtés et dessous du conduit d’évent X”

Profondeur d’encastré une face X”

*** Tablette X” de l’ouverture de l’appareil

WARNING

Do not add any material to the appliance which will come in contact with the

ﬂames, other than that supplied by the manufacturer with the appliance.

AVERTISSEMENT

N’ajoutez pas à cet appareil aucun matériau devant entretien

contact avec les ﬂammes autre que celui qui est fourni avec cet appareil par le fabricant.

*** Maximum horizontal extension:

X”. See installation manual for

greater extensions, minimum vent

lengths and maximum vent lengths.

*** L’extension horizontale maximale: X”.

Référez au manuel d’installation pour des

extensions plus grandes, les longueurs

d’évacuation minimaux et maximum.

The appliance must be vented using the appropriate Napoleon vent kits. See installation

manual for venting speciﬁcations. Proper reinstallation and resealing is necessary after servicing

the vent-air intake system.

L’appareil doit être ventilé à l’aide de l’ensemble d’évacuation propre à Napoleon. Référez au

manuel d’installation pour les spéciﬁcations d’évacuation. Il est nécessaire de bien réinstaller et

resceller l’évacuation après avoir executer l’entretien du système de prise d’air.

Serial Number / N° de Série:

W385-XXXX

REFERENCE# 161746

XXXX

VENTED DECORATIVE GAS APPLIANCE: NOT A SOURCE OF

HEAT, NOT INTENDED FOR USE AS A HEATING

APPLIANCE, NOT FOR USE WITH SOLID FUEL.

APPAREIL À GAZ DÉCORATIF À ÉVACUATION: N’EST PAS

UNE SOURCE DE CHALEUR; N’EST PAS DESTINÉ À ÈTRE

UTILISÉ COMME UN APPAREIL DE CHAUFFAGE; NE

CONVIENT PAS AUX COMBUSTIBLES SOLIDES.

FOR USE WITH GLASS DOORS CERTIFIED WITH THIS APPLIANCE ONLY.

POUR UTILISATION UNIQUEMENT AVEC LES PORTES EN VERRE

CERTIFIÉES AVEC L’APPAREIL.

XX,XXX XX,XXX

For natural gas when equipped with No. XX drill size oriﬁce.

For propane when equipped with No. XX drill size oriﬁce.

Convient au gaz naturel quand l’appareil est muni d’un injecteur de diamètre no. XX.

Convient au propane quand l’appareil est muni d’un injecteur de diamètre no. XX.

Electrical rating: 115V, 60HZ. Less than 12 amperes. Spéciﬁcations électriques: 115V, 60HZ. Moins de 12 ampère.

XX.X% XX.X%

XXXX XXXX XXXX XXXX

CERTIFIED UNDER / HOMOLOGUE SELON LES NORMES: CSA 2.33b - 2008, ANSI Z21.88b- 2008 VENTED GAS FIREPLACE HEATER / APPAREIL DE CHAUFFAGE ALIMENTÉ

AU GAZ ET VENTILÉ

VENTED GAS FIREPLACE HEATER. APPROVED FOR BEDROOM, BATHROOM AND BED-SITTING ROOM INSTALLATION. SUITABLE FOR MOBILE HOME INSTALLATION IF INSTALLED IN ACCORDANCE WITH THE

CURRENT STANDARD CAN/CSA Z240MH SERIES GAS EQUIPPED MOBILE HOMES, IN CANADA OR IN THE UNITED STATES THE MANUFACTURED HOME CONSTRUCTION AND SAFETY STANDARD, TITLE 24 CFR,

PART 3280. WHEN THIS US STANDARD IS NOT APPLICABLE USE THE STANDARD FOR FIRE SAFETY CRITERIA FOR MANUFACTURED HOME INSTALLATIONS, SITES AND COMMUNITIES, ANSI / NFPA 501A.

FOYER DE CHAUFFAGE AU GAZ AVEC ÉVACUATION. HOMOLOGUÉ POUR INSTALLATION DANS UNE CHAMBRE À COUCHER, UNE SALLE DE BAIN ET UN STUDIO. APPROPRIÉ POUR INSTALLATION DANS UNE

MAISON MOBILE SI SON INSTALLATION CONFORME AUX EXIGENCES DE LA NORME CAN/CSA Z240MH SÉRIE DE MAISONS MOBILES ÉQUIPÉES AU GAZ, EN VIGUEUR AU CANADA OU AUX ÉTATS-UNIS DE LA

NORME DE SECURITÉ ET DE CONSTRUCTION DE MAISONS MANUFACTURÉES, TITRE 24 CFR, SECTION 3280. DANS LE CAS OU CETTE NORME D'ÉTATS-UNIS NE PEUT ÊTRE APPLIQUÉE, SE RÉFÉRER A LA NORME

RELATIVE AU CRITÈRE DE MESURES DE SÉCURITÉ CONTRE L'INCENDIE POUR LES INSTALLATIONS DANS LES MAISONS MANUFACTURÉS, LES SITES ET LES COMMUNAUTÉS, ANSI/NFPA 501A.

NOT FOR USE WITH

SOLID FUEL. FOR USE

WITH GLASS DOORS

CERTIFIED WITH THIS

UNIT ONLY.

WARNING

DO NOT ADD ANY MATERIAL

TO THE APPLIANCE, WHICH WILL COME

IN CONTACT WITH THE FLAMES, OTHER

THAN THAT SUPPLIED BY THE

MANUFACTURER WITH THE APPLIANCE.

MINIMUM CLEARANCE TO

COMBUSTIBLE MATERIALS:

TOP 0”

FLOOR 0”

RECESSED DEPTH ONE SIDED 23"

RECESSED DEPTH SEE THRU 13.5”

FRAMING (NOT INCLUDING

FACE MATERIAL)

SIDES 0”

VENT 2"

BACK 0”

MANTLE 15" *

TOP, SIDES & BACK: PER STAND OFF SPACERS FOR FRAMING MATERIALS. FOR FINISHING MATERIALS

SEE OWNERS MANUAL

UN COMBUSTIBLE SOLIDE NE

DOIT PAS ÊTRÉ UTILISÉ AVEC

CET APPAREIL. UTILISER AVEC

LES PORTES VITRÉES

HOMOLOGUÉES SEULEMENT

AVEC CETTE UNITÉ.

AVERTISSEMENT:

N'AJOUTEZ PAS A

CET APPAREIL AUCUN MATÉRIAU DEVANT

ENTRER EN CONTACT AVEC LES FLAMMES

AUTRE QUE CELUI QUI EST FOURNI AVEC

CET APPAREIL PAR LE FABRICANT.

DÉGAGEMENTS MINIMAUX DES

MATÉRIAUX COMBUSTIBLES:

DESSUS 0”

PROFONDEUR D'ENCASTRÉ 25"

PLANCHER 0”

ÉVENT 2"

CÔTES 0”

MANTEAU 15" *

ARRIÉRE 0”

MADE IN CANADA / FABRIQUÉ AU CANADA

WOLF STEEL LTD. BARRIE, ONTARIO, CANADA

ALTITUDE / ÉLÉVATION

INPUT / ALIMENTATION

REDUCED INPUT / ALIMENTATION RÉDUITE

ORIFICE / INJECTEUR

MANIFOLD PRESSURE /

PRESSION AU COLLECTEUR

MINIMUM SUPPLY PRESSURE /

PRESSION D'ALIMENTATION MINIMALE

MAXIMUM SUPPLY PRESSURE /

PRESSION D'ALIMENTATION MAXIMALE

0-4500FT (0-1370M)

30,000 BTU/H

23,000 BTU/H

#38

3.5" WATER COLUMN/D'UNE COLONNE D'EAU

4.5" WATER COLUMN/D'UNE COLONNE D'EAU

7.0" WATER COLUMN/D'UNE COLONNE D'EAU

0-4500FT (0-1370M)

30,000 BTU/H

23,000 BTU/H

#53

10" WATER COLUMN/D'UNE COLONNE D'EAU

11" WATER COLUMN/D'UNE COLONNE D'EAU

13" WATER COLUMN/ D'UNE COLONNE D'EAU

THE APPLIANCE MUST BE VENTED USING THE APPROPRIATE

NAPOLEON VENT KITS. SEE OWNERS INSTALLATION MANUAL

FOR VENTING SPECIFICS. PROPER REINSTALLATION AND

RESEALING IS NECESSARY AFTER SERVICING THE VENT-AIR

INTAKE SYSTEM.

L'APPAREIL DOIT ÉVACUER SES GAZ EN UTILISANT L'ENSEMBLE

D'ÉVACUATION PROPRE A NAPOLEON. RÉFÉRER AU MANUEL

D'INSTALLATION DE PROPRIÉTAIRE POUR L'ÉVACUATION

PRÉCISE. IL EST IMPORTANT DE BIEN RÉINSTALLER ET

RESCELLER L'ÉVENT APRÈS AVOIR ASSURÉ LE MAINTIEN DU

SYSTÉME DE PRISE D'AIR.

CLASSIFICATION: 115V 0.82AMP, 60HZ

W385-2007

MODEL NATURAL GAS /

GAZ NATURAL

LHD50NT

MODEL PROPANE

LHD50PT

SERIAL NUMBER/NO. DE SÉRIE: LV50

ELECTRICAL RATING: 115V 0.82AMP, 60HZ

REFERENCE #

W/N 16131

* MAXIMUM HORIZONTAL EXTENSION / L'EXTENSION

HORIZONTALE MAXIMALE: 2". SEE INSTRUCTION MANUAL FOR GREATER EXTENSIONS.

SEE OWNER'S INSTRUCTION MANUAL FOR MINIMUM AND MAXIMUM VENT LENGTHS.

DESSUS, COTÉS & ARRIÈRE: SELON LES ESPACEURS DE DÉGAGEMENT POUR LES MATÉRIAUX D'OSSATURE

SELON LE MANUEL DE PROPRIÉTAIRE POUR LES MATÉRIAUX DE FINITION.

* L'EXTENSION HORIZONTALE MAXIMALE: 2". RÉFÉRER AU MANUEL D'INSTRUCTION POUR DES EXTENSIONS

PLUS GRANDES. RÉFÉRER AU MANUEL D'INSTALLATION DE PROPRIÉTAIRE.

SAMPLE

VALVE

The rating plate must stay with the appliance at all times. It must not be removed.

W415-3085 / A / 02.28.22 7

operating your appliance

2.0 operating your appliance

To turn the appliance on:

When operating your appliance for the ﬁrst time, there is a required burn-in process that cures materials used

to manufacture the ﬁreplace that may emit both vapors and an odor. These are normal when operating a new

appliance for the ﬁrst time. Ensure adequate air circulation is provided during burn-in process,

2.1 using your appliance

For more detailed information, see your installation manual or contact your authorized dealer.

2.2 on/off components

Batteries must be disposed of according to the local laws and regulations. Some batteries may be

recycled, and may be accepted for disposal at your local recycling center. Check with your

municipality for recycling instructions.

Les piles doivent être mises au rebut conformément aux lois et à la réglementation locales.

Certaines piles peuvent être recyclées et acceptées dans votre centre de recyclage local. Rensei-

gnez-vous auprès de votre municipalité au sujet des directives de recyclage.

Las baterías deben desecharse de acuerdo con las leyes y regulaciones locales. Algunas baterías

pueden reciclarse, y es posible que su centro de reciclado local las acepte para desecharlas.

Consulte en su municipalidad sobre las instrucciones para el reciclado.

| On/off switch | | Battery holder (including switch) | Remote control

| (Optional) (Optional)

(Not supplied)

1. Turn the on/off switch on.

2. Turn gas knob counter-clockwise to the “PILOT” position.

3. Depress and hold gas knob while lighting the pilot with the push button ignitor. Keep knob fully depressed for

one minute, then release.

4. When used for the ﬁrst time, if the burn-in process was not completed by the installer, run appliance

continuously for 4 hours (burn-in).

5. Turn the appliance off. Wait until appliance is completely cool before moving to the next step.

6. Remove the safety barrier and ﬁrebox glass door. Clean ﬁrebox glass door (see “maintenance” section).

Replace ﬁrebox glass door and safety barrier.

W415-3085 / A / 02.28.22

operating your appliance

31.1A

WARNING

• Do not turn on if children or other at risk individuals are near the appliance.

• This appliance is equipped with a pilot which must be lit by hand while following these instructions exactly.

• Before operating, smell all around the appliance area for gas and next to the ﬂ oor because some gas is heavier

than air and will settle on the ﬂ oor.

• Use only your hand to turn the gas control knob. Never use tools. If the knob will not turn by hand, do not try

to repair it. Call a qualiﬁ ed service technician. Force or attempted repair may result in a ﬁ re or explosion.

• Do not use this appliance if any part has been under water. Immediately call a qualiﬁ ed service technician

to inspect the appliance and replace any part of the control system and any gas control which has been

underwater.

FOR YOUR SAFETY READ BEFORE LIGHTING

WHAT TO DO IF YOU SMELL GAS

LIGHTING INSTRUCTIONS

TO TURN OFF GAS

A. Stop! Read the above safety information on this label.

B. Remove batteries from the transmitter and set thermostat to lowest setting, if equipped.

C. Turn off all electrical power to the appliance.

D. Open the glass door, if equipped.

E. Turn the gas knob clockwise to the “OFF” position.

F. Wait ﬁ ve (5) minutes to clear out any gas. If you smell gas including near the ﬂ oor, STOP!

Follow the instructions above in the “WHAT TO DO IF YOU SMELL GAS” section. If you

don’t smell gas; close the glass door and go to the next step.

G. If the appliance is equipped with ﬂ ame adjustment valve turn clockwise to “OFF”.

H. Turn gas knob counter-clockwise to the “PILOT” position. (If the appliance is equipped

with an “ON/OFF” switch, ensure it is in the “ON” position.

I. Depress and hold gas knob while lighting the pilot with the push button ignitor. Keep knob

fully depressed for one minute, then release. If pilot does not continue to burn, repeat steps

E through I.

J. With pilot lit, turn gas knob counter-clockwise to the “ON” position.

K. If equipped with the ﬂ ame adjustment valve, push and turn the knob to high.

L. Turn on all electrical power to the appliance and re-install the batteries into the transmitter, if

equipped. Set thermostat to desired setting, if equipped.

A. Set thermostat to desired setting, if equipped.

B. Turn off all electrical power to the appliance if service is to be performed.

C. Push in gas knob slightly and turn clockwise to the “OFF” position. Do not force.

• Turn off all gas to the appliance.

• Open windows.

• Do not try to light any appliance.

• Do not touch any electric switch; do not use

any phone in your building

• Immediately call your gas supplier from a

neighbour’s phone. Follow the gas supplier’s

instructions.

• If you cannot reach your gas supplier, call

the ﬁ re department.

• If you do not follow these instructions exactly, a ﬁ re or explosion may result causing property damage, personal

injury, or loss of life.

• If applicable, always light the pilot whether for the ﬁ rst time or if the gas supply has run out with the glass door

opened or removed.

add gas knob

add gas valve

Ensure that a continuous gas ﬂ ow is at the burner before installing the door. When lit for the ﬁ rst time, the appliance

will emit an odor for a few hours. This is a normal temporary condition caused by the “burn-in” of paints and

lubricants used in the manufacturing process and will not occur again. After extended periods of non-operation

such as following a vacation or a warm weather season, the appliance may emit a slight odor for a few hours. This

is caused by dust particles in the heat exchanger burning off. In both cases, open a window to sufﬁ ciently ventilate

the room.

For vent free appliances ONLY: if the appliance shuts off, do not relight until you provide fresh air. If appliance

keeps shutting off, have it serviced. Keep burner and control compartment clean.

note:

When lighting and re-lighting, the gas knob cannot be turned from pilot to off unless the knob is

depressed.

2.3 operating and lighting instructions

W415-3085 / A / 02.28.22 9

operating your appliance

Manual adjustments to your ﬁreplace must only be made when the appliance is off and complete cool.

Allow safety barrier to cool before making adjustment.

The CBL36-1/CBL46 models are equipped with a manual gas control knob (located on the valve) that adjusts the

ﬂame height to suit your preference. To access the gas control knob, remove your safety barrier, control cover and

door trim (see “maintenance” section for instructions on how to remove these components).

Use only your hand to turn the gas control knob (never use tools). If the knob will not turn by hand, do not try to

repair it. Contact a qualiﬁed technician.

2.3.1 turndown

Flame adjustment

An optional remote control is available to turn the appliance on and off, refer to the instructions provided with the

remote control.

W415-3085 / A / 02.28.22

operating your appliance3.0 remote control layout

3.1 general transmitter layout

3.2 temperature display

Remove the battery cover on the back of the transmitter to expose the °C /

°F dip switch. Move the dip switch to your desired temperature mode.

Selected temperature mode will appear in the top right corner beside the

room temperature.

The receiver switch must be in the REMOTE position for the transmitter to function. This remote system operates

using radio frequency signals sent by the transmitter to the receiver. It is recommended that the distance between

the transmitter and receiver never exceeds 20’ and 10’ if the receiver is located within the ﬁreplace’s outer or inner

cavity surrounding an insert. Low batteries will also affect operational distance.

AAA

°F °C

TRANSMITTER

REAR VIEW

OFF

LCD

DISPLAY

ON / OFF

BUTTON

THERMOSTAT

BUTTON

DOWN

BUTTON

FLAME

INDICATOR

LOW

BATTERY

INDICATOR

THERMOSTAT

BULB

SIGNAL

INDICATOR

CHILD-PROOF

FUNCTION

INDICATOR

TEMPERATURE

INDICATOR

THERMOSTAT

SET

TEMPERATURE

ROOM

TEMPERATURE

The remote control is optional for the BL36-1 and BL46 models.

note:

W415-3085 / A / 02.28.22 11

operating your appliance

3.3 in the event of a battery failure

If the receiver batteries fail, the appliance will no longer turn on or off. To operate the appliance in the event of

a battery failure, the slide switch located on the receiver may be switched to the “ON” position to operate the

appliance.

23.3

A. Press the on / off key on the transmitter. The transmitter display will

show all active icons on the screen. A single “beep” from the receiver will

conﬁ rm reception of the command.

Blue LCD Display

On / Off Key

Up / Down Arrow Key

Mode Key

Temperature Key

73 23

76°F

Room Temperature

Set Temperature

76°F

MAX

76°F

OFF 76°F 76°F

76°F

Flame Off Flame at level 1 Flame at level 5 Flame at “Hi” level 6

76°F

child lock

76°F

OFF 76°F

76°F

68 76°F

76°F

OFF 76°F

76°F

IPI 76°F

CPI

SMART

°F °C

ADD TITLE: TEMPERATURE DISPLAY

A. With the system in the off position, press the temperature key

and the mode key at the same time to change from degrees ºF to

ºC.

B. Look at the LCD screen on the transmitter to verify that a ºC or ºF

is visible to the right of the room temperature display.

ADD TITLE: HAND HELD REMOTE OPERATION

The remote control has six (6) ﬂ ame levels. With the system on and the ﬂ ame level at the maximum, press the

down arrow key once and it will reduce the ﬂ ame height by one step until the ﬂ ame is turned off.

The up arrow key will increase the ﬂ ame height each time it is pressed. If the up arrow key is pressed while

the system is on but the ﬂ ame is off, the ﬂ ame will come on at the high position. A single “beep” will conﬁ rm

reception of the command.

ADD TITLE: FLAME HEIGHT

Blue LCD Display

On / Off Key

Up / Down Arrow Key

Mode Key

Temperature Key

73 23

76°F

Room Temperature

Set Temperature

76°F

MAX

76°F

OFF 76°F 76°F

76°F

Flame Off Flame at level 1 Flame at level 5 Flame at “Hi” level 6

76°F

child lock

76°F

OFF 76°F

76°F

68 76°F

76°F

OFF 76°F

76°F

IPI 76°F

CPI

SMART

°F °C

If the appliance is equipped with a hot air circulating fan, the speed of

the fan can be controlled by the remote system. The fan speed can be

adjusted through six (6) speeds.

A. Use the mode key to guide you to the fan control icon.

B. Use the up/down arrow keys to turn on/off or adjust the fan

speed. A single “beep” will conﬁ rm reception of the command.

ADD TITLE: FAN SPEED

Blue LCD Display

On / Off Key

Up / Down Arrow Key

Mode Key

Temperature Key

73 23

76°F

Room Temperature

Set Temperature

76°F

MAX

76°F

OFF 76°F 76°F

76°F

Flame Off Flame at level 1 Flame at level 5 Flame at “Hi” level 6

76°F

child lock

76°F

OFF 76°F

76°F

68 76°F

76°F

OFF 76°F

76°F

IPI 76°F

CPI

SMART

°F °C

ADD TITLE: CHILD PROOF FUNCTION

This function will lock the keys to avoid unsupervised operation.

A. Press the mode and up keys at the same time.

B. To de-activate this function, press the mode and up keys at the same time.

Blue LCD Display

On / Off Key

Up / Down Arrow Key

Mode Key

Temperature Key

73 23

76°F

Room Temperature

Set Temperature

76°F

MAX

76°F

OFF 76°F 76°F

76°F

Flame Off Flame at level 1 Flame at level 5 Flame at “Hi” level 6

76°F

child lock

76°F

OFF 76°F

76°F

68 76°F

76°F

OFF 76°F

76°F

IPI 76°F

CPI

SMART

°F °C

Blue LCD Display

On / Off Key

Up / Down Arrow Key

Mode Key

Temperature Key

73 23

76°F

Room Temperature

Set Temperature

76°F

MAX

76°F

OFF 76°F 76°F

76°F

Flame Off Flame at level 1 Flame at level 5 Flame at “Hi” level 6

76°F

child lock

76°F

OFF 76°F

76°F

68 76°F

76°F

OFF 76°F

76°F

IPI 76°F

CPI

SMART

°F °C

Blue LCD Display

On / Off Key

Up / Down Arrow Key

Mode Key

Temperature Key

73 23

76°F

Room Temperature

Set Temperature

76°F

MAX

76°F

OFF 76°F 76°F

76°F

Flame Off Flame at level 1 Flame at level 5 Flame at “Hi” level 6

76°F

child lock

76°F

OFF 76°F

76°F

68 76°F

76°F

OFF 76°F

76°F

IPI 76°F

CPI

SMART

°F °C

Blue LCD Display

On / Off Key

Up / Down Arrow Key

Mode Key

Temperature Key

73 23

76°F

Room Temperature

Set Temperature

76°F

MAX

76°F

OFF 76°F 76°F

76°F

Flame Off Flame at level 1 Flame at level 5 Flame at “Hi” level 6

76°F

child lock

76°F

OFF 76°F

76°F

68 76°F

76°F

OFF 76°F

76°F

IPI 76°F

CPI

SMART

°F °C

When the desired blower speed is selected, the blower will automatically come on 5 minutes after the main

burner has been turned on and remain on twelve minutes after it has been turned off.

note:

ADD TITLE: NIGHT LIGHT

The auxiliary function controls the AUX power outlet on the control module

which controls the Night Light™.

A. Use the mode key to guide you to the AUX icon.

B. Pressing the up arrow key will activate the Night Light™.

C. Pressing the down arrow key will turn the Night Light™ off. A single

“beep” will conﬁ rm the reception of the command.

Blue LCD Display

On / Off Key

Up / Down Arrow Key

Mode Key

Temperature Key

73 23

76°F

Room Temperature

Set Temperature

76°F

MAX

76°F

OFF 76°F 76°F

76°F

Flame Off Flame at level 1 Flame at level 5 Flame at “Hi” level 6

76°F

child lock

76°F

OFF 76°F

76°F

68 76°F

76°F

OFF 76°F

76°F

IPI 76°F

CPI

SMART

°F °C

The life span of the remote batteries depends on various factors: quality of the batteries,

the number of ignitions, etc.

When the transmitter batteries are low, a battery icon will appear on the LCD display

before all battery power is lost. When the batteries are replaced, this icon will disappear.

When the receiver batteries are low, no “beep” will be emitted from the receiver when

it receives an on/off command. This in an alert for the receiver that there’s low battery.

When the batteries are replaced the “beep” will be emitted from the receiver when the on/off key is pressed.

If the batteries of the receiver or transmitter are low, the appliance can be turned on manually by sliding the

three position slider switch on the receiver to the on position. This will bypass the remote control feature and the

appliance main burner will come on if the gas valve is in the

position.

ADD TITLE: IN THE EVENT OF A POWER FAILURE

If the receiver is equipped with batteries they will enable ﬂ ame height control or on/off function to control the

appliance during a power failure. Blower and Night Light™ operation is not possible. Refer to “appliance

operation” section when communications between receiver and transmitter have been lost. The receiver will

emit a “beep” sound to conﬁ rm programming has been successful once power is restored. During a power

failure, if the appliance was on, the ﬂ ame height will stay at the setting prior to the failure. If off when the failure

occurs and then turned on, the ﬂ ame height will come on at “Hi”. The ﬂ ame height can then be controlled by the

remote.

ADD TITLE: LOW BATTERY / MANUAL BYPASS

ADD TITLE: Night Light Dimmer Control

Blue LCD Display

On / Off Key

Up / Down Arrow Key

Mode Key

Temperature Key

73 23

76°F

Room Temperature

Set Temperature

76°F

MAX

76°F

OFF 76°F 76°F

76°F

Flame Off Flame at level 1 Flame at level 5 Flame at “Hi” level 6

76°F

child lock

76°F

OFF 76°F

76°F

68 76°F

76°F

OFF 76°F

76°F

IPI 76°F

CPI

SMART

°F °C

If equipped, the auxiliary function controls the Night Light™ with dimmable

control.

A. Use the mode key to guide you to the Night Light™ icon.

B. The intensity of the output can be adjusted through 6 levels.

Use the up/down arrow keys to adjust the output level. A single beep

will conﬁ rm reception of the command.

ADD TITLE: CONTINUOUS PILOT / INTERMITTENT PILOT (CPI / IPI) SELECTION

A. When the transmitter is in the off position, use the mode key to guide

you to the CPI mode icon.

B. Press the up/down to switch between IPI and CPI modes. A single

beep will conﬁ rm reception of the command.

Blue LCD Display

On / Off Key

Up / Down Arrow Key

Mode Key

Temperature Key

73 23

76°F

Room Temperature

Set Temperature

76°F

MAX

76°F

OFF 76°F 76°F

76°F

Flame Off Flame at level 1 Flame at level 5 Flame at “Hi” level 6

76°F

child lock

76°F

OFF 76°F

°F

76°F

68 76°F

76°F

OFF 76°F

76°F

IPI 76°F

CPI

SMART

°F °C

Blue LCD Display

On / Off Key

Up / Down Arrow Key

Mode Key

Temperature Key

73 23

76°F

Room Temperature

Set Temperature

76°F

MAX

76°F

OFF 76°F 76°F

76°F

Flame Off Flame at level 1 Flame at level 5 Flame at “Hi” level 6

76°F

child lock

76°F

OFF 76°F

76°F

68 76°F

76°F

OFF 76°F

76°F

IPI 76°F

CPI

SMART

°F °C

Blue LCD Display

On / Off Key

Up / Down Arrow Key

Mode Key

Temperature Key

73 23

76°F

Room Temperature

Set Temperature

76°F

MAX

76°F

OFF 76°F 76°F

76°F

Flame Off Flame at level 1 Flame at level 5 Flame at “Hi” level 6

76°F

child lock

76°F

OFF 76°F

76°F

68 76°F

76°F

OFF 76°F

76°F

IPI 76°F

CPI

SMART

°F °C

If the appliance is equipped with a CPI/IPI toggle switch, set the CPI/IPI

to CPI position to enable remote CPI operation. If the switch is set to IPI

then it will only work in IPI regardless of what is set on the remote control

handset.

note:

3.4 low battery

W415-3085 / A / 02.28.22

clearances around ﬁreplace

!WARNING

• Your appliance, gas/electrical connections, venting and various key components are hidden behind the wall. It is

critical that no screws penetrate these components. Failure to follow instructions may cause improper operation,

damage, personal injury or ﬁre. Always use a stud ﬁnder and only screw into studs.

4.0 clearances around ﬁreplace

Without making adequate provisions to account for the heat, the temperatures above the ﬁreplace will be hot,

making it unsuitable for mounting a TV or other objects sensitive to heat without risk of damage.

Installing a mantel between this appliance and electronics or other materials that may be sensitive to heat will

reduce the effect of direct heat on them.

The size and material of the mantel will affect the allowable clearance above your ﬁreplace. Incorrect placement

could become a ﬁre hazard. Consult your installation manual and/or authorized dealer for more information before

mounting a mantel, a shelf or any other object above your appliance.

Your ﬁreplace, gas/electrical connections and vent are hidden directly behind the ﬁnished wall. Great care should

be taken to avoid screwing or nailing into these components. Always use a stud ﬁnder to determine stud location

and only screw into studs.

Do not screw into the area around the ﬁreplace opening as some of your appliance may be hidden behind the

ﬁnished wall. Refer to your installation manual and/or contact your local dealer for more information.

Fireplaces

generate radiant

heat. Do not put

objects in front

of the appliance

(minimum

distance of 4 feet

[1.21m]).

The area above a ﬁreplace gets hot.

Combustible objects or materials must

never be placed in this area. For mini-

mum clearances, refer to installation

manual or your authorized dealer.

!WARNING

W415-3085 / A / 02.28.22 13

clearances around ﬁreplace

4.1 optional heat management system

The Universal Heat Management system is an optional gravity vent kit that allows you to manage the heat

produced by the appliance at and around the ﬁreplace.

We recommend installing the Universal Heat Management system kit during the installation of the appliance

BEFORE the gas is installed.

For more information, contact your local authorized dealer.

Reduced mantel

clearances

Grill to expel

warm air into the

room

Reduced

temperatures

above fireplace

W415-3085 / A / 02.28.22

clearances around ﬁreplace

4.2 clearances around appliance (TV and valuable objects)

* TV applications were tested with the minimum enclosure dimensions and the maximum recess permissible.

This data is provided in good faith and is not a guarantee for every application and television. Care and

consideration should be taken when planning these installations to ensure the temperatures around the TV meet

all manufacturer’s recommended operating temperatures. Increasing the height of the mantel and/or TV above

the ﬁreplace opening, the protrusion of mantel and the volume of the enclosure all have the effect of reducing

the temperature above the ﬁreplace. It is always recommended to use the optional heat management kit

when considering mounting a television above the ﬁreplace.

6” min.

Appliance opening

2.5” min.*

2” min.

(3” max.

recommended)

6” min.

2.5” min.*

Enclosure Enclosure

TV bracket

Flush installation with

mantel

Recessed installation with

protrusion

Appliance opening

2” min.

(3” max. recommended)

Appliance

opening

Enclosure

TV bracket

Flush installation without

mantel

Appliance Appliance

Appliance

The volume of

air must be

added to the

enclosure to

accomodate

the recessed

area.

6” min.

Enclosure

TV bracket

Partially recessed installation with mantel

Appliance opening

Appliance

Enclosure A

3” min.

See “minimum clearance to

mantle” section (installation

manual).

Mantle clearances reduced

from opening with the use of the

universal heat management

system.

12”

max.

2.5” min.*

2” min.

(3” max.

recommended)

6” min.

Appliance opening

2.5” min.*

2” min.

(3” max.

recommended)

Enclosure

TV bracket

Flush installation with mantel

Enclosure

Appliance

These applications are

only acceptable when the

Universal Heat Management

kit is installed.

!WARNING

W415-3085 / A / 02.28.22 15

clearances around ﬁreplace

• Electronic appliance temperatures must be validated at the time of installation as air ﬂow

characteristics within the room can vary and maximum acceptable operating temperatures can vary from

appliance to appliance. Electronic appliances cannot be used where the electronic appliance temperature

exceeds the manufacturer’s maximum allowable operating temperatures (see electronic appliance

manufacturer’s speciﬁcations). Operating a television above the manufacturer’s maximum allowable

operating temperature will result in premature failure.

• Mantel height and depth must conform to mantel clearance requirements speciﬁed in this manual, see

“minimum clearance to combustible mantel” section in installation manual.

• Electronic appliance temperatures may be further reduced by increasing the horizontal distance between

the front of the electronic appliance and the front edge of the mantel or by increasing dimension “A” or “B”.

However, increasing the gap between the top of the mantel and the bottom of the electronic appliance

beyond the maximum recommended ﬁgure, typically results in higher temperatures. Minimum clearance

between the mantel and bottom of the electronic appliance should be maintained to allow air circulation

below and behind the electronic appliance.

note:

W415-3085 / A / 02.28.22

maintenance5.0 maintenance

!WARNING

• Turn off the gas and electrical power before servicing the appliance.

• Appliance may be hot. Do not service until appliance has cooled.

For qualiﬁed technicians only:

• Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous

operation. Verify proper operation after servicing.

• This appliance and its venting system should be inspected before use and at least annually by a qualiﬁed service

person.

• The ﬂow of combustion and ventilation air must not be obstructed.

DOS

• Clean your safety barrier regularly to prevent the

build up of excessive lint/dust from carpeting, pet

hair, etc. Vacuum using the brush attachment.

• Always use ammonia-free glass cleaners.

• Service your appliance annually and/or as

required. Service must be conducted by a qualiﬁed

technician.

• Keep your appliance area clear and free of

combustible materials, gasoline, or other ﬂammable

vapors and liquids.

• Check to see that the burner ignites completely

on all openings when turned on. A 5 to 10 second

total light-up period is satisfactory. Service as

required.

DON’TS

• Attempt to service the electrical or gas

components. Contact a qualiﬁed technician.

• Use excessive force.

• Use abrasive cleaners on glass.

• Paint the pilot assembly.

• Place objects too close to the ﬁreplace opening.

For any questions and/or concerns regarding your appliance, maintenance and service, please contact your

authorized dealer.

note:

!WARNING

Buff lightly with a clean dry soft cloth to remove accumulated dust or ﬁ ngerprints. Clean both sides of the glass

after the ﬁ rst 10 hours of operation with an ammonia-free glass cleaner.

Thereafter, clean as required. If the glass is not kept clean permanent discoloration and / or blemishes may

result. Contact you local authorized dealer / distributor for complete cleaning instructions.

Razor blades, steel wool, or other metallic objects must not be used on both surfaces of the glass. Doing so

can remove a thin layer of metal from the razor blades, steel wool, or other metallic objects that may then be

deposited onto the coating. This can result in a discoloured stain or scratch-like mark. More importantly, this can

scratch the glass surface, thereby reducing its strength.

Do not operate the appliance with broken glass, as leakage of ﬂ ue gases may result.

Contact your local authorized dealer / distributor for complete cleaning instructions.

If the glass should ever crack or break while the ﬁ re is burning, do not open the door until the ﬁ re is out. Do not

operate the appliance until the glass has been replaced. Contact you local authorized dealer / distributor for

replacement parts. DO NOT SUBSTITUTE MATERIALS.

5.1A

Vinegar-based glass cleaners have demonstrated an ability to provide a clean, streak free glass surface.

note:

• Do not clean glass when hot! Do not use abrasive cleaners to clean glass.

Firebox Glass Door :

5.1 care of glass

WARNING

Buff lightly with a clean dry soft cloth to remove accumulated dust or ﬁ ngerprints. Clean both sides of the glass

after the ﬁ rst 10 hours of operation with an ammonia-free glass cleaner.

Thereafter, clean as required. If the glass is not kept clean permanent discoloration and / or blemishes may

result. Contact you local authorized dealer / distributor for complete cleaning instructions.

Razor blades, steel wool, or other metallic objects must not be used on both surfaces of the glass. Doing so

can remove a thin layer of metal from the razor blades, steel wool, or other metallic objects that may then be

deposited onto the coating. This can result in a discoloured stain or scratch-like mark. More importantly, this can

scratch the glass surface, thereby reducing its strength.

Do not operate the appliance with broken glass, as leakage of ﬂ ue gases may result.

Contact your local authorized dealer / distributor for complete cleaning instructions.

If the glass should ever crack or break while the ﬁ re is burning, do not open the door until the ﬁ re is out. Do not

operate the appliance until the glass has been replaced. Contact you local authorized dealer / distributor for

replacement parts. DO NOT SUBSTITUTE MATERIALS.

5.1A

Vinegar-based glass cleaners have demonstrated an ability to provide a clean, streak free glass surface.

note:

• Do not clean glass when hot! Do not use abrasive cleaners to clean glass.

Do not use ammonia-based cleaners.

W415-3085 / A / 02.28.22 17

maintenance

This appliance is factory equipped with tempered glass. Use only replacement parts as supplied by the appliance

manufacturer. DO NOT SUBSTITUTE MATERIALS.

Replacement glass/frame assembly shall be replaced as a complete unit as supplied by the appliance

manufacturer.

5.2 care of plated parts

6.1

If the appliance is equipped with plated parts, you must clean ﬁ ngerprints or other marks from the plated surfaces

before operating the appliance for the ﬁ rst time. Use an ammonia-free or vinegar-based cleaner and a towel

to clean. If not cleaned properly before operating for the ﬁ rst time, the marks can cause permanent blemishes

on the plating. After the plating is cured, the ﬁ ngerprints and oils will not affect the ﬁ nish and little maintenance

is required, just wipe clean as needed. Prolonged high temperature burning with the door ajar may cause

discolouration on plated parts.

The protective wrap on plated parts is best removed when the assembly is at room temperature but this can

be improved if the assembly is warmed (i.e. using a hair dryer or similar heat source).

note:

SAFETY BARRIER

A barrier designed to reduce the risk of burns from the hot viewing glass is provided with the

appliance and must be installed.

Lift the safety barrier off the four shoulder screws and remove from the appliance. Reverse this step to install.

WARNING

• Glass may be hot. Do not touch glass until cooled.

• If equipped with door latches that are part of a safety system, they must be properly engaged. Do not

operate the appliance with latches disengaged.

• Facing and/or ﬁ nishing materials must not interfere with air ﬂ ow through air openings, louvre openings,

operation of louvres, or doors/access for service. Observe all clearances when applying combustible

materials.

• Before door is removed, turn the appliance off and wait until appliance is cool to the touch. Doors are heavy

and fragile so handle with care.

47.1

5.3 safety barrier removal

W415-3085 / A / 02.28.22

maintenance

To remove, slide the back edge of the door trim up and out of the glass and door frame.

To install, slide the back edge of the door trim down between the glass and door frame. Insert downwards.

5.4 door trim removal

These spring latches make up the spring

relief system for the appliance. Ensure

the door opens freely and closes sealed.

note:

When mounting the door, ensure there is

equal space on both left and right sides.

This allows for easy installation of the

front.

note:

CBL46 illustrated

Leave a hand on the glass door during entire door removal. The glass door is secured to the ﬁrebox with four

(CBL36-1) or six (CBL46) spring latches. Pull the handles of the latches forward, then lift the latches out from the

door frame to release the door. Next, lift the door up until the bottom edge clears the bottom shoulder screws of

the appliance. Carefully grip the top and bottom of the door, lifting it off the appliance.

Reverse these steps to reinstall the door.

Ensure safety screen is installed correctly.

5.5 ﬁrebox glass door removal

W415-3085 / A / 02.28.22 19

replacements

6.0 replacement parts

!WARNING

• Failure to position the parts in accordance with this manual or failure to use only parts speciﬁcally approved

with this appliance may result in property damage or personal injury.

Contact your dealer for questions concerning prices and policies on replacement parts. Normally, all parts can

be ordered through your Authorized dealer / distributor.

For warranty replacement parts, a photocopy of the original invoice will be required to honour the

claim.

When ordering replacement parts always give the following information:

• Model & Serial Number of appliance

• Installation date of appliance

• Part number

• Description of part

• Finish

For service parts, see your Installation manual.

W415-3085 / A / 02.28.22

accessories

7.0 accessories

REF.

#Description Part Number Stocked

CBL36-1 CBL46

1Classic Surround (Black) CSL36K CSL46K

2Decorative Porcelain Panel PRPL36 PRPL46

3Shore Fire Kit SFKS SFKM Yes

4Beach Fire Kit BFKXS BFKM Yes

5Mineral Rock Kit MRKXS MRKM Yes

6Blower GZ600KT / AUB

Items may not appear exactly as illustrated.

La page charge ...

Continental Fireplaces CBL46NT Manuel utilisateur

Marque: Continental Fireplaces

Modèle: CBL46NT

Catégorie: Cheminées

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Continental Fireplaces CBL46NT User manual

Continental Fireplaces CBL46NT Manuel utilisateur

Continental Fireplaces CBL46NT Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents