GE Lighting STR-SCIDB Guide d'installation

Taper
Guide d'installation
Full Color Direct Connect
Light Strip & Extension
Installation Guide
Light Strip Contents
Light Strip Extension
Contents
Light Strip + Power Supply
1. 16ft Full Color Light Strip
2. Power supply with plug
3. Re-connector wire
Light Strip Extension
1. 8ft Full Color Light Strip
2. Extension cable (power supply
sold separately)
3. Snap connector
Whats Included
(Devices each sold separately)
Easy Set Up
Set up your Light Strips
with three easy steps:
STEP 1
Connect to the Cync App,
powered by Savant.
STEP 2
Trim to desired length.
STEP 3
Prep surface and install.
Set Up in the CYNC App
For set up help, visit cyncsupport.gelighting.com or call 1-844-302-2943
GE and C by GE are trademarks of General Electric Company. Used under trademark license.
Amazon, Alexa, and all related logos are trademarks of Amazon.com, Inc. or its affiliates.
Google and other related marks and logos are trademarks of Google LLC.
STEP 1
Plug in and power on your Light Strip by pressing
the On/Off button on the power supply.
STEP 2
Download the Cync App, powered by Savant,
on your smartphone.
STEP 3
Add your smart lights to the Cync App.
Measure & Trim to Size (If desired)
STEP 1
Measure where you’re planning to install
your lights. If your space requires Light
Strip Extensions, make sure to attach them
before trimming your strips.
NOTE: Cutting anywhere else will
permanently damage the strip.
STEP 2
With your Light Strip unplugged, safely
cut where the trim points are indicated.
Make sure the strip is not plugged
in at the wall when cutting.
NOTE: Make sure surface is dry & free
of oil contamination. For best results,
tape the strip in temperatures above
50°F/10°C.
NOTE: Adhesive may damage walls or painted
surfaces if removed. Adhesive is single use,
so don’t peel lights and try to re-stick to wall.
You will need to use double-sided tape if
re-application is needed.
Prep the Surface & Install Your Strip
STEP 3
STEP 2
Working in 6 inch sections, peel o
the adhesive backing.
STEP 1
Clean & dry surface.
2000K
G
B
R
G
R
2000K
Stick to surface, 6 inches at a time, pressing
and holding each section for 10 seconds.
Strip Bending Options
Connector
LED
90°
LED at bend
90°
Do not bend near
Snap connector
Extend Strip & Manually
Enable Light Shows
(If applicable)
Remove plastic cover from end to link strips.
NOTE: Use the Snap connector to strengthen
the connecting point. Extend up to 32ft.
STEP 1
Unplug the power supply and remove
the plastic end cap cover. Attach extension
to the Light Strip.
STEP 2
Plug in power supply.
FCC Statement
Warning: Changes or modifications to this unit not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help
The device must not be co-located or operating in conjunction with any other antenna or transmitter.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.FCC RF Radiation Exposure
Statement Caution: To maintain compliance with the FCC’s RF exposure guidelines,
place the product at least 20cm from nearby persons.
IC statement
This device complies with RSS247 of Industry Canada. Cet appareil se conforme à RSS247 de Canada
d'Industrie.
This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device. appareils radio exempts de licence.
Son fonctionnement est sujet aux deux conditions suivantes: (1) le dispositif ne doit pas produire de
brouillage prejudiciable, et (2) ce dispositif doit accepter tout brouillage recu, y compris un brouillage
susceptible de provoquer un fonctionnement indesirable.
This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled
environment. This transmitter must be installed to provide a separation distance of at least 20cm from all
persons and must not be collocated or operating in conjunction with any other antenna or transmitter.
Cet équipement est conforme aux limites d'exposition aux rayonnements IC RSS-102 définies pour un
environnement non contrôlé.Cet émetteur doit être installé pour fournir une distance de séparation d'au
moins 20 cm de toutes les personnes et ne doit pas être colocalisé ou fonctionner en conjonction avec une
autre antenne ou émetteur.
Like your new Full Color Direct
Connect Light Strip & Extension?
Share your experience!
Leave a review where you purchased
the product.
TM
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10

GE Lighting STR-SCIDB Guide d'installation

Taper
Guide d'installation

dans d''autres langues