S.R.Smith 6004 Fiber Optic Illuminator Guide d'installation

Marque: S.R.Smith

Modèle: 6004 Fiber Optic Illuminator

Taper: Guide d'installation

79-15018-00 REV D2 www.srsmith.com Page 1 of 4

10.75”

MAXIMUM SOIL HEIGHT:

DO NOT ALLOW FILL TO

EXCEED THIS LEVEL!

12”

9.75”10.5”

22.75”

4”

13”

11.5”

2004-AS™

AUTO SYNCHRONIZED ILLUMINATORS

WARNING: DO NOT INSTALL

WITHIN 1.5M (5 FT.) OF A POOL,

SPA, OR HOT TUB.

ADVERTISSEMENT: NE PAS

INSTALLER A MOINS DE 1,5M

D’UNE PISCINE OU D’UNE CUVE

DE RELAXATION.

INSTALLATION MANUAL

ELECTRICAL

Voltage required: 120VAC 60Hz

Power consumption: 250 Watts max

Current usage: 2.0 amps

LAMP

Type: Quartz-halogen, proprietary design

Lamp life: 400-700 hrs average

Listing

UL file number E220601

SPECIFICATIONS

CONSTRUCTION

Case: High Impact Polycarbonate

Ventilation: 110 cu ft/min air volume

Acoustic rating: 50dB(A)

Weight: 13 lbs.

79-15018-00 REV D2 www.srsmith.com Page 2 of 4

ELECTRICAL CONNECTIONS

2004-AS

120V 60Hz ONLY

IF A SELF-CONTAINED

REMOTE IS DESIRED, ORDER

THE OPTIONAL RM1

SEE BELOW

CONTROL SEQUENCE

1. From off to on the first time.

Light on, color wheel stationary

with the color wheel at position it

was on when turned off. (#2 to

#1)

2. Toggle from on to off to on.

Light on, color wheel moves to

white, pauses, then continues

rotating. (#1 to #2 to #1)

3. Toggle from on to off to on.

Light on, color wheel stops on

the desired color. (Another

toggle will start the color wheel

rotating again.) (#1 to #2 to #1)

4. From on to off.

Light off, color wheel off. Sets

the color that will come on when

initially turned on again. (#1 to

#2)

NOTES:

1. FOR EXTERNAL AUTO CONTROL YOU MUST

LEAVE TOGGLE SWITCH IN THE “ON

POSITION.

2. IF USING RM1 WIRELESS REMOTE CONTROL

TOGGLE SWITCH MUST BE ON THE BOTTOM

POSITION (#3).

LINE

120V

60Hz

HOT (BLACK)

NEUTRAL (WHITE) WHITE TO UNITS 1 & 2

GREEN TO UNITS 1 & 2 GROUND (GREEN)

BLACK TO UNIT 1

BLACK TO UNIT 2

EXTERNAL SWITCH CONNECTION

FOR SYNCHRONIZING 2 OR MORE UNITS

(2004-AS OR FX AS LIGHTS)

Wireless Remote Info:

The use of an RM1, Wireless Remote Control, is intended for use in a 2004-AS ONLY when used as

a standalone unit. It is NOT intended for use for s

nchronization of multi

le units.

79-15018-00 REV D2 www.srsmith.com Page 3 of 4

Refer to the diagram on the front of this manual for the following procedures.

1) See our general installation manual for fiber and conduit installation in the pool. This

manual covers the 2004-AS series illuminator installation only.

2) Cut the fiber conduits so they will enter the installation base approximately halfway. Cut

the electrical conduit so it will protrude past the conduit hole 1” or less (FIG A). Pull all

fiber optic cables at least 12” through the top of the installation base.

3) Follow the port assembly procedures on the back of this manual.

4) Place the chassis on the installation base. Secure the illuminator with the two screws

supplied. Snap the port into the clip on the chassis. Make sure it seats firmly into the clip

(FIG B).

5) Make the electric connections as shown on the previous page. Make sure no wires

interfere with the cooling fan or color wheel.

6) a) If installing in the ground:

Backfill halfway up the installation base. Allow ample height for top soil and landscaping.

Do not allow the vents on the bottom of the illuminator to be blocked. This will cause the

illuminator to overheat and shut off.

b) If surface mounting:

Use proper securing screws for the surface type you are attaching to, using the 2 holes

provided on the base. Example: For concrete, use proper concrete screws. For wood

surface, use proper wood screws.

FIG A

APPROVED CONDUITS FOR USE WITH FIBER

OPTIC CABLES

• White PVC conduit/pipe SCH 40 or SCH 80

• Gray PVC conduit/pipe SCH 40 or SCH 80

• Flexible PVC pipe

• Black poly pipe

• Any other suitable conduit

FIBER CONDUIT HOLE

AT LEAST 12” OF FIBER

MUST BE PROTRUDING PAST HOLE

ELECTRICAL CONDUIT HOLE

ELECTRIC CONDUIT SHOULD

PROTRUDE 1” OR LESS

USE SWEEP ELLS OR HEAT BEND

FOR GENTLE RADIUS

FIG B

INSTALLATION GUIDELINES

79-15018-00 REV D2 www.srsmith.com Page 4 of 4

SMALL

UP TO 100 FIBERS

MEDIUM

101 TO 200

LARGE

201 TO 300 301 TO 400

XTRA LARGE

TIP SIZES

PORT ASSEMBLY/FIBER TERMINATION

A) Insure that the total fiber count of

all fiber tubings is 400 or less. If

you have more than 400 individual

fibers, you will need a second

illuminator. The maximum

capacity of the System 2000™

series port is 400 fibers (optional

CCS-450 for expanding fiber

capacity to 450 fibers sold

separately).

B) Insert the proper size tip into the

port and twist with pliers to lock

(fig. 1).

C) Strip back all fiber casings no less

than 4 inches (fig. 2). Take care

not to nick the fibers.

D) Insert the bare fibers into the port

so ALL fibers protrude past the

port tip (fig. 3). Tighten the port

compression nut down on the

fiber casing (fig. 4).

E) IMPORTANT: If the port tip is not

completely full, insert scrap

individual fibers into the tip until it

is completely full (fig. 5). This will

keep the lit fibers perpendicular to

the lamp, and prevent the fibers

from overheating.

F) Plug in the hot knife (p/n FS-118)

and allow it to heat up. Apply firm

downward pressure on the fibers,

with the blade touching the port

tip at a slight angle (fig. 6.) Do not

saw at the fibers. Allow the heat

of the knife to slowly trim the

fibers. Ease the pressure as the

knife almost completes the cut.

Unplug the hot knife and place it

in a safe place to cool.

S.R.Smith 6004 Fiber Optic Illuminator Guide d'installation

Marque: S.R.Smith

Modèle: 6004 Fiber Optic Illuminator

Taper: Guide d'installation

Télécharger le PDF

rapport

dans d''autres langues

English: S.R.Smith 6004 Fiber Optic Illuminator Installation guide

Documents connexes