Powerfist 9035304 Le manuel du propriétaire

SPECIFICATIONS

HAZARD DEFINITIONS

INTRODUCTION

SAFETY

WARNING! Read and understand all instructions before

using this tool. The operator must follow basic

precautions to reduce the risk of personal injury

and/or damage to the equipment.

WORK AREA

PERSONAL SAFETY

WARNING! Wear personal protective equipment

approved by the Canadian Standards Association (CSA)

or American National Standards Institute (ANSI).

PERSONAL PROTECTIVE EQUIPMENT

PERSONAL PRECAUTIONS

SPECIFIC SAFETY PRECAUTIONS

WARNING! DO NOT let comfort or familiarity with

product (gained from repeated use) replace strict

adherence to the tool safety rules. If you use this tool

unsafely or incorrectly, you can suffer serious personal

injury.

ELECTRICAL SAFETY

WARNING! Do not touch or handle a live tool with any

part of your body that is wet or damp. Wet skin

reduces resistance to electrical current, increasing

the danger of a serious or fatal shock.

WARNING! To reduce risk of electric shock, be certain

that the plug is connected to a properly grounded

receptacle.

WARNING! All wiring should be performed by a

qualified electrician.

POWER CORD

POLARIZED PLUG

ELECTROMAGNETIC FIELDS

WARNING! Shut off the electrical tool or device and

move away if you feel faint, dizzy, nausea or shocks.

Seek medical attention.

UNPACKING

WARNING! Do not operate the tool if any part is

missing. Replace the missing part before operating.

Failure to do so could result in a malfunction and

personal injury.

ASSEMBLY & INSTALLATION

INSTALLING THE ATTACHMENTS

OPERATION

HIGH SPEED DRILL BIT ATTACHMENT

IDENTIFICATION KEY

SHARPENING DRILL BITS

Caution! Sharpened drill bits may be

hot. Handle with care to prevent minor

burn injuries.

CLAMPING DRILL BITS

Drill bit size

Clamp setup

STANDARD KNIFE AND SCISSOR

ATTACHMENT

IDENTIFICATION KEY

SHARPENING KNIVES

CAUTION! Keep hands away from the

blade. Handle knives and scissors with

care to prevent injuries.

SHARPENING SCISSORS

STRAIGHT-EDGE CHISEL AND PLANE

BLADE ATTACHMENT

IDENTIFICATION KEY

SHARPENING CHISEL AND PLANE BLADES

NOTICE! Do not hold the blade in place against a

running grinding wheel for extended periods as this

may cause irregular sharpening

CARE & MAINTENANCE

WARNING! Only qualified service personnel should

repair the tool. An improperly repaired tool may

present a hazard to the user and/or others.

REMOVING AND INSTALLING THE

GRINDING WHEEL

CLEANING

CAUTION! Do not clean with metal

scouring pads. Metal pieces from

the pad can come in contact with

the electrical parts and increase

the risk of shock.

STORAGE

DISPOSAL

TROUBLESHOOTING

PARTS BREAKDOWN

PARTS LIST

#

DESCRIPTION

QTY

SPÉCIFICATIONS

DÉFINITIONS DE DANGER

INTRODUCTION

SÉCURITÉ

AVERTISSEMENT ! Veuillez lire et comprendre toutes

les instructions avant d'utiliser cet outil. L'utilisateur

doit respecter les précautions de base lorsqu'il utilise

cet outil afin de réduire le risque de blessure ou de

dommage à l'équipement.

AIRE DE TRAVAIL

SÉCURITÉ PERSONNELLE

AVERTISSEMENT ! Portez de l'équipement de

protection personnelle homologué par l'Association

canadienne de normalisation (CSA) ou l'American

National Standards Institute (ANSI).

ÉQUIPEMENT DE PROTECTION PERSONNELLE

PRÉCAUTIONS PERSONNELLES

CONSIGNES DE SÉCURITÉ SPÉCIFIQUES

AVERTISSEMENT! Ne permettez PAS au confort ou à

votre familiarisation avec l'outil (obtenus après un

emploi répété) de se substituer à une adhésion stricte

aux règles de sécurité de l'outil. Si vous utilisez cet

outil de façon dangereuse ou incorrecte, vous pouvez

subir des blessures corporelles graves.

La page est en cours de chargement...

Powerfist 9035304 Le manuel du propriétaire

Powerfist 9035304 Le manuel du propriétaire

dans d''autres langues

Autres documents