VTech VH6222 Manuel utilisateur

Catégorie
Écouteurs
Taper
Manuel utilisateur
Go to businessphones.vtech.com
to register your product for
enhanced warranty support and
the latest VTech product news.
VH6222
Over-the-ear Office
Wireless Headset
with Dongle
User’s manual
BC
Congratulations
on your purchase of this VTech product. Before using this product,
please read the Important safety information.
This Abridged user’s manual provides you with the basic installation
and use instructions. A limited set of features are described in
abbreviated form.
Visit businessphones.vtech.com/support/downloads to download a
full set of installation and operation instructions.
The software application
Software application - Installation and Operation Guide
For customer service or product information, visit our website at
businessphones.vtech.com or call 1 (800) 595-9511. In Canada, please
dial 1 (800) 267-7377.
For VH6222 headset:
HVIN: 35-800001HD
FCC ID: EW780-1360-00
IC: 1135B-80136000
For Dongle VU-060:
FCC ID: EW780-1391-00
IC: 1135B-80139100
Skype® and Skype for Business® are registered trademarks of Microsoft Corporation.
* The VTech Control supports Skype version 7.1-7.40. Later versions of Skype are not
supported by VTech Control for remote headset call control.
The VH6222 includes a cordless headset, charger, and a Dongle. The
Dongle functions as a headset base so that this product allows you to
have handsfree phone conversations.
The Dongle allows you to connect your headset using either one of
the following methods:
PHONE mode - Connect to an IP phone
Use the Dongle to connect the headset and your VTech/SNOM IP
phone. The headset acts as a supplementary device that can make
and receive calls with the IP phone.
PC mode - Connect to a computer
Use the Dongle to connect the headset and your PC. You can
make and receive VoIP calls through Skype®* or Skype for
Business®, using
the
VTech Control software application.
Introduction
What’s in the box
Your product package contains the following items. Save your sales
receipt and original packaging in the event warranty service is
necessary.
Headset charger Headset charger
power adapter
User's manual Wireless headset
11 earbuds
Dongle
BC
XL LMS
LS
M
XL LMS
Table of contents
Getting started
Headset overview .........................1
Headset lights ................................ 2
Headset alert tones ...................3
Headset alert prompts ..............3
Headset charger overview ......... 4
Dongle overview ..........................5
Dongle LED lights ......................5
Power up the headset charger .. 6
Charge the headset battery ....... 6
Connection methods ....................7
PHONE mode ............................7
PC mode .....................................7
PHONE mode -
Connect to an IP phone........... 8
Plug the Dongle to
a VTech/SNOM IP phone ........ 8
Plug the Dongle to
a computer ................................ 9
PC mode -
Connect to a computer ..........11
Wear the headset ........................ 12
Change the earbud and wear
the headset ...............................12
Operate
Headset power on/off ...............13
PHONE mode - Operate with
an IP Phone .............................. 14
Before use ................................ 14
Make and receive calls ........... 14
PC mode - Operate with a
computer ..................................15
Before use .................................15
Make and receive calls ............15
Caller ID announce ..................15
Sound settings ............................ 16
Headset ringer ........................ 16
Anti-Startle (G616) .................. 16
Change audio bandwidth ......17
Temporary ringer silencing ... 18
Volume control ....................... 18
Mute .......................................... 18
Appendix
Registering Headset to
Dongle ..................................... 19
Register your Headset to
the Dongle .............................. 19
Frequently asked questions .....20
Maintenance ............................... 24
Important safety information ....25
Safety information ...................25
Especially about cordless
headsets ................................... 26
Precautions for users
of implanted cardiac
pacemakers ..............................27
For C-UL compliance ................. 28
Mesures de sécurité
importantes ............................. 28
FCC Part 68 and ACTA ................32
FCC Part 15 .................................. 34
California Energy Commission
battery charging testing
instructions................................35
Limited warranty ........................ 36
Technical specifications ............. 39
Disclaimer and Limitation of
Liability .....................................40
1
Getting started
Headset overview
1 – Ear hook
2 – ON/OFF button and LED light
Press to make, answer or end a call.
See Headset lights for lights behavior.
3 – Magnetic charging contacts
4 – + (Volume up) / - (Volume down)
Press to adjust the headset ringer volume while in idle mode, or the listening
volume while on a call.
5 – MUTE
Mute the microphone during a call.
6 – Earpiece
7 – Microphone
5
6
7
4
2
31
2
Getting started
Headset lights
Color LED light status Meaning
Red Steady light on The battery is low and the headset is in
the charger.
Flash every 10 seconds The battery is low and the headset is
not in the charger.
Flash 3 times Powering off.
Blue Steady light on The battery is fully charged.
Flash every 10 seconds The headset is not in the charger.
Flash 2 times every
3 seconds The headset is in use.
Flash 3 times Powering on.
Flash 4 times every
4 seconds There is an incoming call.
Purple Steady light on The battery is well charged.
Red and
blue Alternate slowly The headset is not registered.
Alternate quickly The headset is trying to register to a
headset base.
Off Light off The battery is depleted.
The headset is powered off.
ON/OFF button and LED light
Press to make, answer or end a call.
3
Getting started
Headset alert
Headset alert tones
Alert tone behavior Meaning
One short beep every
30 seconds
The microphone is muted.
Two beeps Error alert tone.
The speaking volume has reached its highest or
lowest setting.
Any key is pressed while the headset is out of
range.
Two low beeps Call waiting alert tone.
Two rapid beeps every
20 seconds
Low battery warning.
Three rapid beeps every
20 seconds
The headset is out of range.
Three rapid beeps The headset is powering on or off.
Headset alert prompts
Alert prompt Meaning
“Mute on” The microphone is muted.
“Mute off” The microphone is re-activated.
“Not registered” ON/OFF button is pressed while the headset
is not registered.
“Out of range” The headset is on a call and out of range.
Any key is pressed while the headset is out of
range.
“Low battery” ON/OFF button is pressed while the headset
battery is low.
4
Getting started
Headset charger overview
1 – Magnetic charging mount
• Place the headset here for charging.
2 – LED light
Steadily red while the headset charging in the charger.
2
1
5
Getting started
Dongle overview
Color LED light status
Green Steady green when the Dongle is not in use.
Steady green for three seconds when the Dongle is
deregistered from the headset.
Flashes very quickly when there is an incoming call.
Flashes quickly every three seconds when the headset is in
use.
Red Steady red when the Dongle is not registered.
Flashes very quickly when the Dongle is registering to a
headset.
Flashes quickly when the Dongle is entering deregistration
mode.
Flashes slowly when the headset is muted.
Dongle LED lights
1
1 – LED light button
• Press and hold for about 4 seconds to enter the registration mode.
• For LED light patterns, see Dongle LED lights below.
6
Getting started
Charge the headset battery
Hang the headset onto the magnetic charging mount.
The magnet holds the headset in place.
The LED light on the charger will turn steady red while charging.
Notes
For optimal performance, charge the headset battery for at least 30 minutes before
use. The battery is fully charged after 2 hours of continuous charging. When the
headset is not in use, recharge by hanging it onto the headset charger.
The headset battery is built-in. If you need to replace the headset, visit our website
at businessphones.vtech.com or call 1 (800) 595–9511 to get a replacement. In
Canada, dial 1 (800) 267-7377.
Power up the headset charger
1. Plug the small end of the headset charger
power adapter at the back of the headset
charger.
2. Plug the large end into an electrical outlet
not controlled by a wall switch.
7
Getting started
Connection methods
Choose one of the following methods to connect your headset for
operation in either PHONE mode or PC mode.
PHONE mode
Connect to an IP phone
You can connect the headset to an IP phone by plugging the
Dongle to the USB port on your VTech/SNOM IP phone. The
headset acts as a supplementary device that can make and receive
calls with the IP phone.
PC mode
Connect to a computer
You can connect the headset to your PC by plugging the Dongle to
the USB port on your computer the to your PC. You can make and
receive VoIP calls through Skype or Skype for Business, using
the
software application
.
8
Getting started
PHONE mode - Connect to an IP phone
Plug the Dongle to a VTech/SNOM IP phone
Connect the headset to an IP phone using the Dongle.
You can use the headset to make or answer calls with the IP phone
connected.
1. Plug the Dongle to the USB port on your VTech/SNOM IP phone.
The Dongle LED light will turn steady green.
2. At the telephone base of your VTech/SNOM IP Phone, press to
turn on the headset mode.
Depending on the IP phone model the status icon will appear
on the LCD of your IP phone, or the LED light on the key will
turn on.
Test the headset after connection:
Press
the
ON/OFF button on the headset to make, answer, or end
a call, using the telephone line to which the IP phone is connected.
9
Getting started
PC mode - Connect to a computer
Plug the Dongle to a computer
Connect the headset to a computer using the Dongle.
You can then use the headset for VoIP (Voice over IP) calls through
your computer.
1. Plug the Dongle to the USB port on your computer. The Dongle
LED light will turn steady green.
2. Install the VTech Control.
Visit businessphones.vtech.com/support/downloads
to download and install the software. You can also download
the Installation and Operation Guide there for installation
and operation instructions of the software.
10
Getting started
3. After you have installed the VTech Control, check to make sure
the audio setting is properly configured in your Windows system.
If you have installed Skype and/or Skype for Business and want
to use them with your headset, make sure the audio settings are
configured correctly in the programs as well.
a) Audio settings in Microsoft® Windows®
(Windows 7 / Windows 8 / Windows 10) system:
i. Click Start menu and choose Control Panel.
ii. Click Hardware and Sound and then click Manage
audio devices under the Sound menu.
iii. Click the Playback tab and make sure VTech Headset is set as
the default speaker.
iv. Click the Recording tab and make sure VTech Headset is set
as the default microphone.
b) Audio settings in Skype (Skype 7.1-7.40):
i. Launch the Skype program.
ii. Click on Tools, then Options.
iii. Click on Audio settings.
iv. Make sure VTech Headset is selected under the speakers and
microphone settings.
Notes
The VTech Control does not support the App versions of Skype, including both
mobile APP and desktop APP.
The VTech Control supports Skype version 7.1-7.40. Later versions of Skype are not
supported by VTech Control for remote headset call control.
After the installation of VTech Control, Skype will prompt a message “VTechControl.
exe is requesting access to Skype. Choose Allow Access to connect your Skype to
VTech Control.
PC mode - Connect to a computer
Windows® is a registered trademark of Microsoft Corporation.
11
Getting started
c) Audio settings in Skype for Business 2016:
i. Launch the Skype for Business program.
ii. Click on Options, then Audio Device.
iii. Make sure VTech Headset is selected under the Audio device
setting.
PC mode - Connect to a computer
IMPORTANT INFORMATION
Periodically check for software updates. For more details, download the
VTech Control - Installation and Operation Guide under the product
page of VH6222 on businessphones.vtech.com/support/downloads for
installation and operation instructions of the software.
12
Getting started
Wear the headset
Change the earbud and wear the headset
There are 11 earbuds included, with different sizes and types.
1. The medium-sized gray earbud is pre-attached to the headset. You
can try the other earbuds and choose one that best fits your ear.
Remove them from your ear after trying.
2. Remove the pre-attached medium-sized gray earbud from the
headset and then attach your desired earbud.
Make sure the
protruding bump is
pointing towards the
microphone when
placed on your ear.
The protruding bump
on the earbud holds
the headset securely
in your ear.
3. Adjust the angle of the headset to fit your ear, and then hook the
headset on your ear.
The microphone should be pointing towards your mouth, as
close to your cheek as possible without touching.
XL LMS
LS
M
XL LMS
12
Microphone
13
Headset power on/off
To power on the headset:
Press and hold ON/OFF button for two seconds.
The LED light flashes blue three times, and you hear three
beeps when it is being powered on.
To power off the headset:
Press and hold ON/OFF button for four seconds.
The LED light flashes red three times, and you hear three beeps
when it is being powered off.
Operate
14
Operate
PHONE mode - Operate with an IP Phone
Before use
Make sure you have plugged your Dongle to the USB port on your
VTech/SNOM IP Phone.
Make and receive calls
To make a call:
1. Press the ON/OFF button on the headset. You hear a dial tone in
the headset earpiece.
2. Dial the telephone number using the dialing keys on the IP phone.
To answer a call:
Press the ON/OFF button on the headset to answer an
incoming call.
You hear the caller through the headset earpiece.
To end a call:
Press the ON/OFF button on the headset to end a call. The EHS
connection automatically releases the line on your IP phone.
15
Operate
PC mode - Operate with a computer
Before use
Make sure you have plugged your Dongle to the USB port on your
computer, and have already installed the VTech Control on your
computer, before you use your headset.
Download the VTech Control and the
Installation and Operation
Guide
at
businessphones.vtech.com/support/downloads
, under
the product page of VH6222.
Unzip and install the VTech Control after download.
Make and receive calls
You can make and receive VoIP calls with your VTech Control through
Skype and Skype for Business.
Caller ID announce
The Caller ID announce feature with your VTech Control lets you know
who is calling without having to look at the display.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46

VTech VH6222 Manuel utilisateur

Catégorie
Écouteurs
Taper
Manuel utilisateur

dans d''autres langues