VTech VH621 Manuel utilisateur

Go to businessphones.vtech.com

to register your product for

enhanced warranty support and

the latest VTech product news.

VH621

Convertible Ofﬁce

Wireless Accessory

Headset

User’s manual

Congratulations

on your purchase of this VTech product. Before using this product,

please read the Important safety information.

This user’s manual provides you with instructions on how to set up and

register your new handset. For instructions on using the headset, see

the user’s manual that came with your VH6210/VH6211 headset or

DECT telephone base to which the VH621 headset is registered.

For customer service or product information, visit our website at

businessphones.vtech.com or call 1 (800) 595-9511. In Canada, please

dial 1 (800) 267-7377.

T

Compatible with

Hearing Aid T-Coil

TIA-1083

Telephones identiﬁed with this logo have reduced noise and

interference when used with most T-coil equipped hearing aids and

cochlear implants. The TIA-1083 Compliant Logo is a trademark of the

Telecommunications Industry Association. Used under license.

What’s in the box

Your product package contains the following items. Save your sales

receipt and original packaging in the event warranty service is

necessary.

User’s manual Battery with battery

compartment cover

Four over-the-ear hooks

Four earbuds

Behind-the-neck bandOver the head band

Headset charger Headset charger

power adapter

Cordless headset with

earbud attached

Sponge cover

for ear hooks

Two spare rubber rings

for headset earpiece

Table of contents

Getting started

Headset overview .........................1

Headset lights ................................ 2

Headset alert tones ...................3

Headset alert prompts ..............3

Headset charger overview ......... 4

Install headset battery ..................5

Power up the headset

charger ....................................... 6

Charge the headset battery ....... 6

Position the headset .....................7

Over-the-ear hook ....................7

Over-the-head band ............. 10

Over-the-neck-band ..............12

Operation

Headset operation ..................... 14

Power on/off the headset ..... 14

Make a call ............................... 14

Answer a call ............................ 14

End a call ...................................15

Headset ringer .........................15

Temporary ringer

silencing ....................................15

Volume control ........................15

Mute .......................................... 16

Call waiting

(functions only if registered

to a DECT telephone) ............. 16

Appendix

Adding and registering

a new headset .......................... 17

Option 1: Register a headset

to your VH6210/VH6211

headset base ........................... 18

Option 2: Register a headset

to a VU-060 dongle ............... 19

Option 3: Register a headset to

a DECT cordless

telephone base....................... 20

Deregistering headsets .............. 21

Deregister all headsets from

your headset base ...................21

Deregister all headsets from

your Dongle .............................21

Maintenance ................................22

Important safety information ......23

Safety information ...................23

Especially about cordless

headsets ................................... 24

Precautions for users of

implanted cardiac

pacemakers ..............................25

For C-UL compliance ................. 26

FCC Part 68 and ACTA ...............30

FCC Part 15 ...................................32

Limited warranty .........................33

Technical speciﬁcations ............. 36

Disclaimer and Limitation of

Liability ......................................37

1

Getting started

Headset overview

1 – VOL+/VOL-

• Slide the volume switch to the right or left to adjust the headset ringer volume

while in idle mode, or the listening volume while on a call.

2 – ON/OFF button and LED light

• Press to make, answer or end a call.

• See Headset lights for lights behavior.

3 – MUTE

• Mute the microphone during a call.

4 – Battery with cover attached

• The battery is permanently attached to the battery compartment cover and they

are inseparable from each other. Remove the entire assembled unit to replace

the battery.

5 – Microphone

1

2

3

4

5

2

Getting started

Headset lights

Color LED light status Meaning

Red Steady light on The battery is low and the headset is

charging in the headset base.

Flash every 10 seconds The battery is low and the headset is

not in the headset base.

Flash 3 times Powering off.

Blue Steady light on The battery is fully charged.

Flash every 10 seconds The headset is not in the headset base.

Flash 2 times every

3 seconds

The headset is in use.

Flash 3 times Powering on.

Flash 4 times every

4 seconds

There is an incoming call.

Purple Steady light on The battery is well charged.

Red and

blue

Alternate slowly The headset is not registered.

Alternate quickly The headset is trying to register to a

headset base.

Off Light off The battery is depleted.

No battery is installed.

The headset is powered off.

ON/OFF button and LED light

Press to make, answer or end a call.

3

Getting started

Headset alert

Headset alert tones

Alert tone behavior Meaning

One short beep every

30 seconds

• The microphone is muted.

Two beeps

• Error alert tone.

• The speaking volume has reached its highest or

lowest setting.

• Any key is pressed while the headset is out of

range.

Two low beeps

• Call waiting alert tone.

Two rapid beeps

every 20 seconds

• Low battery warning.

Three rapid beeps

every 20 seconds

• The headset is out of range.

Three rapid beeps

• The headset is powering on or off.

Headset alert prompts

Alert prompt Meaning

“Mute on”

• The microphone is muted.

“Mute off”

• The microphone is re-activated.

“Not registered”

• ON/OFF button is pressed while the headset is

not registered.

“Out of range”

• The headset is on a call and out of range.

• Any key is pressed while the headset is out of

range.

“Low battery”

• ON/OFF button is pressed while the headset

battery is low.

4

Getting started

Headset charger overview

1

1 – Magnetic charging mount

• Place the headset here for charging.

5

Getting started

Install headset battery

CAUTION

• Do not disassemble the battery from its battery compartment cover.

NOTES:

• You will hear the voice prompt "Low battery" when you press the

ON/OFF

button while the headset battery is low.

• When fully charged, the headset battery supports up to 5 hours of talk time or 48

hours of standby time.

• To order a replacement battery pack (model BT291865), visit our website at

businessphones.vtech.com or call 1 (800) 595-9511. In Canada, dial

1 (800) 267-7377.

1. Align the metallic contacts between the battery and the battery

compartment, and then place the battery down.

2. Slide the battery until it clicks into place.

3. Charge it for at least 30 minutes.

6

Getting started

Power up the headset charger

1. Plug the small end of the headset

charger power adapter at the

back of the headset charger.

2. Plug the large end into an

electrical outlet not controlled by

a wall switch.

Charge the headset battery

Hang the headset onto the magnetic charging mount.

The magnet holds the headset in place.

• The light will turn:

- steady red when the headset

battery is low while charging;

- steady purple when the battery

is well charged; and

- steady blue when the battery

is fully charged.

NOTE:

• For optimal performance, charge the headset battery for at least 30 minutes before

use. The battery is fully charged after 2 hours of continuous charging. When the

headset is not in use, recharge by hanging it onto the headset charger.

7

Getting started

Position the headset

Over-the-ear hook

Attach the headset accessories and wear the headset:

1. Mount the earhooks over your ear and insert the earbuds to check

the best ﬁtting. Remove them from your ear after checking.

2. Insert your desired earhook to the headset.

• Rotate it until it securely holds in place.

Note

• If you accidentally ripped off the rubber ring, use a spare rubber ring to replace it.

Rubber ring

8

Getting started

Position the headset

3. Insert your desired earbud to the headset.

• Make sure the protruding bump is pointing towards your

mouth when placed on your ear. The protruding bump on the

earbud holds the headset securely in your ear.

4. Hook the headset on your ear. Adjust the angle of the headset until

the microphone is pointing towards your mouth.

9

Getting started

Position the headset

Remove the earbud and earhook:

Remove the earbud and earhook, when you need to replace them

in the Over-the-ear hook, when you need to change to the

over-the-head and behind-the-neck style.

1. Hold both sides of the earbud. Twist and pull the earbud until it

separates from the earpiece.

2. Rotate the earhook to vertical direction.

3. Pull the earhook until it separates from the headset.

To re-insert another set of earbud and earhook, refer to the previous

section.

10

Getting started

Position the headset

Over-the-head band

Attach the headband and wear the headset:

1. With the headset at a vertical angle (microphone pointing down),

insert the headset earpiece into the headband.

2. Rotate the headset to a horizontal direction until it holds into place.

Note

• If you accidentally ripped off the rubber ring, use a spare rubber ring to replace it.

Rubber ring

11

Getting started

Position the headset

3. Adjust the headband to ﬁt your head.

4. Rotate the angle of the headset until the microphone is pointing

towards your mouth.

• Make sure the protruding bump is pointing towards your

mouth when placed on your ear.

The protruding bump on the earbud holds the headset

securely in your ear.

12

Getting started

Position the headset

Over-the-neck-band

Attach the neckband and wear the headset:

1. With the headset at a vertical angle (microphone pointing down),

insert the headset earpiece into the neckband.

Note

• If you accidentally ripped off the rubber ring, use a spare rubber ring to replace it.

2. Rotate the headset to a horizontal direction until it clicks into place.

Rubber ring

13

Getting started

Position the headset

3. Place the neckband around your neck and over your ears.

4. Adjust and rotate the angle of the headset until the microphone is

pointing towards your mouth.

• Make sure the protruding bump is pointing towards your

mouth when placed on your ear. The protruding bump on the

earbud holds the headset securely in your ear.

14

Operation

Headset operation

Power on/off the headset

Power on the headset before use.

To power on the headset:

• Press and hold

ON/OFF button for two seconds.

The

LED light ﬂashes blue three times and you hear three beeps

when it is being powered on.

Power off the headset if it will not be used for a long time.

To power off the headset:

• Press and hold

ON/OFF button for four seconds.

The

LED light ﬂashes red three times and you hear three beeps

when it is being powered off.

Prolonged exposure to high volume levels using the headset may damage

your hearing.

Make a call

1.

Follow the instructions in your telephone user’s manual for making

calls.

2. Press

the

ON/OFF button

on the headset to

join the call.

You can hang

up the call at your telephone at any time to leave the call.

The headset will continue the call.

Answer a call

• Press

the

ON/OFF button

on the headset to answer an incoming

call.

You hear the caller through the headset earpiece.

15

Operation

Headset operation

End a call

1. Press

the

ON/OFF button

on the headset to leave the phone

conversation at the headset.

2.

H

ang

up the call at your telephone to end the call.

Headset ringer

The headset base and headset do not have external ringers. When

you receive calls, the headset earpiece rings.

To change the volume of the earpiece ringer:

• Slide the volume switch at the top of the headset towards VOL+ or

VOL- when the headset is not in use.

To turn off the earpiece ringer:

• Slide the volume switch at the top of the headset towards VOL- until

you hear two beeps when the headset is not in use.

Temporary ringer silencing

Press MUTE

to temporarily silence the ringer in the headset earpiece.

This silences the ringer without disconnecting the call. The next

incoming call rings normally at the preset volume.

Volume control

To adjust the listening volume:

• While on a call, slide the volume switch at the top of the headset

towards VOL+ or VOL- to adjust the listening volume.

NOTE:

• When the listening volume reaches the minimum or maximum setting, you hear two

beeps.

16

Operation

Headset operation

Mute

The mute function turns off the headset microphone. You can hear the

caller, but the caller cannot hear you.

To mute a call:

• Press MUTE

on the headset to turn off the

headset microphone. The voice prompt "Mute

on" plays. The MUTE | SPARE BATT light on the

headset base flashes and a short beep plays

every 30 seconds.

To take a call off mute:

• Press MUTE on the headset to resume the

two-way conversation. You hear the voice

prompt "Mute off".

Call waiting (functions only if registered to a DECT telephone)

When you subscribed to call waiting

service from your telephone service

provider, you hear an alert tone if there

is an incoming call while you are on

another call.

• Press down the VOL+/VOL- switch to

put the current call on hold and take

the new call.

• Press down the VOL+/VOL- switch to

switch back and forth between calls.

La page est en cours de chargement...

VTech VH621 Manuel utilisateur

VTech VH621 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents