AT&T TL7910 Manuel utilisateur

User’s manual

TL7910

DECT 6.0 cordless headset

Congratulations

on your purchase of this AT&T product.

Unify your everyday business communications with the AT&T

TL7910 DECT 6.0 Cordless Headset. Whether you want to

connect directly to your phone line, deskset or computer, you

can with the TL7910 headset. Control costs and support your

mobile workforce with connectivity to Voice over IP (VoIP)

services like

Skype® and Microsoft Lync®

. A magnetic charger

in the cradle ensures the headset fits and charges securely—so

you’ll never run out of battery during long calls. With up to 12

hours of hands-free talk time and a range of up to 500 feet,

you’re free to work wherever your work is.

Before using this AT&T product, please read the Important

safety information section on pages 47-49 of this manual.

Please thoroughly read this user’s manual for the feature

operations and troubleshooting information necessary to install

and operate your new AT&T product. You can also visit our

website at www.telephones.att.com or call

1 (800) 222-3111. In Canada, dial 1 (866) 288-4268.

This telephone meets the California Energy Commission

regulations for energy consumption. Your telephone is set up to

comply with the energy-conserving standards right out of the

box. No further action is necessary.

Visit www.telephones.att.com/headsets

for a complete

list of AT&T phones that have been tested and found to be

compatible with the TL7910.

Skype® and Microsoft Lync® are registered trademarks of Microsoft Corporation.

the AT&T logo are trademarks of AT&T Intellectual Property licensed to

Advanced American Telephones, San Antonio, TX 78219. Printed in China.

Model number: TL7910

Type: DECT 6.0 cordless headset

Serial number:

Purchase date:

Place of purchase:

Both the model and serial numbers of your AT&T product can be

found on the bottom of the headset base.

Save your sales receipt and original packaging in case it is

necessary to return this product for warranty service.

Telephones identified with this logo have reduced noise and

interference when used with most T-coil equipped hearing

aids and cochlear implants. The TIA-1083 Compliant Logo is a

trademark of the Telecommunications Industry Association. Used

under license.

Cordless headset with

earbud attached

Parts checklist

Check to make sure the headset package includes the following

items. Save your sales receipt and original packaging in the

event warranty service is necessary.

Headset base

Telephone

line cord

Line splitter

Headset base

power adapter

USB cableBehind the neck band

Corded phone

connection cable

Three over the ear hooksFive earbuds

Battery

with battery

compartment

cover attached

User's manual Quick start guide

Two over the head bands CD-ROM

Optional accessory

The TL7910 headset and base is also compatible with the

TL7100 handset lifter.

For more information about the handset lifter, visit our website at

www.telephones.att.com.

TL7100

User’s manual

TL7910

DECT 6.0 cordless headset

Table of contents

Getting started

Introduction .................................... 1

Quick reference guide -

headset ......................................... 2

Headset lights ........................... 2

Headset alert tones ................ 4

Quick reference guide -

headset base ............................. 5

Headset base lights ................ 5

Installation ...................................... 8

Colored labels ........................... 8

Digital subscriber line

(DSL) ............................................... 8

Battery installation ..................... 9

Headset base installation

and battery charging ............10

Headset base installation .......11

Installation options ................11

Option 1: Connect the

headset to a telephone

wall jack ......................................12

Option 2: Connect the

headset to a corded

phone ...........................................13

Option 3: Connect

the headset to your

computer ....................................15

Headset attachments ...............18

Earbud ..........................................18

Over the ear hook ..................19

Over the head band .............. 22

Behind the neck band ..........24

Operation

Headset operation .....................27

Power on/off the

headset ........................................27

PHONE mode and

PC mode ..................................... 27

PHONE mode................................28

Make a call.................................28

Answer a call ............................28

End a call ....................................29

Voice command .......................29

Headset ringer .........................29

Caller ID announce ................30

Temporary ringer

silencing ......................................30

Call waiting ................................30

Options while on calls .............31

Volume control ........................31

Mute ..............................................32

Switching between PHONE

mode and PC mode ..............33

Appendix

Adding and registering

headsets .....................................34

Registration options ..............34

Register a headset to your

TL7910 headset base ...........35

Register a headset to

an AT&T DECT cordless

telephone base .......................36

Deregistering headsets ............38

Deregister all headsets

from your TL7910

headset base ............................38

Troubleshooting ..........................39

Maintenance..................................46

Important safety

information ................................47

Safety information..................47

Especially about cordless

headsets .....................................48

Precautions for users

of implanted cardiac

pacemakers ...............................49

For C-UL compliance ................50

Mesures de sécurité

importantes ...............................50

FCC Part 68 and ACTA............. 54

FCC Part 15 ...................................56

California Energy Commission

battery charging testing

instructions .................................57

Limited warranty .........................58

Technical specifications ..........61

DECT 6.0 digital

technology .................................62

Operating range ......................62

Extended range and

clarity ...........................................62

Encrypted for added

security ........................................62

Index

Index .................................................63

Introduction

The TL7910 is a cordless headset and base that allows you to

have handsfree phone conversations. It can be used in different

ways depending on your needs. Choose from the following three

options. Connect your TL7910:

To a telephone line only (page 12). Connect the headset to a

telephone wall jack. Use the telephones on the same telephone

line to make or answer calls. The headset is a supplementary

device that can join the calls.

To a traditional corded telephone (pages 13-14). Connect

the headset to a corded telephone. If you also install a

lifter (AT&T TL7100, purchased separately) on your corded

telephone, you can use the headset to remotely control the

lifter for answering or hanging up a call.

To both a PC and telephone line (pages 15-17). Connect

a phone line to the headset base and the USB cable to

your PC. You can make and answer VoIP calls through

Skype or Microsoft Lync, or landline calls using the

AT&T Softphone Call Manager. You can also use the voice

command feature to make or answer calls after you have

installed the AT&T Softphone Call Manager.

Install the AT&T Softphone Call Manager using the

CD-ROM provided in the package.

-OR-

Visit www.telephones.att.com/downloads to

download the software. Unzip and install the file after

download.

For installation and operation instructions of the software,

refer to the Installation and Operation Guide which can

also be found in the CD-ROM provided or the web site stated

above.

•

Getting started

1

2

Getting started

light status

Red On when the headset battery is low and the headset

is charging in the headset base.

Flashes every 10 seconds to indicate the battery is

low when the headset is not in the headset base.

Flashes three times to indicate the headset is

powering off.

•

Blue On when a registered headset is charging in the

headset base.

Flashes three times to indicate the headset is

powering on.

Flashes twice every three seconds when the headset

is in use.

Flashes four times every four seconds when there is

an incoming call in PHONE mode.

Flashes every 10 seconds when a registered headset

in idle mode is out of the headset base.

•

Red and blue Flashes slowly when the headset is not registered.

Flashes quickly when the headset is trying to

register to a headset base.

•

Off The battery is dead.

No battery is installed.

The headset is powered off.

•

Quick reference guide - headset

Headset lights

(On/off button and light)

Press to make, answer or end a call

(pages 28-29).

Getting started

VOL+/VOL-

Slide the volume switch

to the right or left to

adjust the headset

ringer volume while

in idle mode (page 29),

or the listening volume

while on a call

(page 31).

Earpiece

Microphone

The microphone

incorporates noise

canceling technology

for clearer calls.

FLASH

Press to answer an

incoming call when

you receive a call

waiting alert during a

call (page 30).

Quick reference guide - headset

Battery with cover

attached

Remove to replace the

battery.

MUTE/VOICE

Press to mute the microphone

during a call (page 32).

Press to mute the ringer in

the earpiece when there is an

incoming call (page 30).

Press to initiate the voice

command feature (page 29).

3

4

Getting started

One long beep The headset is ready to take your voice

command. (You have to install the AT&T

Softphone Call Manager before using the

voice command feature. For installation and

operation instructions of the software, refer

to the Installation and Operation Guide

which can be found in the CD-ROM in the

package. You may also visit

www.telephones.att.com/

downloads to download it.)

•

One short beep every

30 seconds

The microphone is muted. •

Two beeps Error alert tone.

The speaking volume has reached its highest

or lowest setting.

Any key is pressed while the headset is out

of range.

•

Two low beeps Call waiting alert tone.•

Two rapid beeps

every 20 seconds

Low battery warning.•

Three rising beeps A conference call has started.•

Three rapid beeps

every 20 seconds

The headset is out of range.

The headset is not yet registered.

•

Three rapid beeps The headset is powering on or off.•

Quick reference guide - headset

Headset alert tones

5

Getting started

Quick reference guide - headset base

Magnetic charging mount

Place the headset here for

charging.

MUTE (light)

PAIR

Use to initiate headset

registration or

deregistration.

PHONE (mode button

and light)

PC (mode button

and light)

MUTE

(Red)

On when you are registering a headset.

Flashes when a call is muted.

Flashes when you are deregistering headset(s) from the

headset base.

•

PHONE

(Blue)

On when PHONE mode is selected as the default mode

on the idle headset base.

Flashes four times every four seconds when there is an

incoming call.

Flashes twice every three seconds when the headset is in

use in PHONE mode.

Flashes slowly when a call is on hold in PHONE mode.

•

PC

(Blue)

On when PC mode is selected as the default mode on

the idle headset base.

Flashes twice every three seconds when the headset is in

use in PC mode.

Flashes slowly when a call is on hold in PC mode.

•

Headset base lights

6

Getting started

VOLUME /MICROPHONE

Press the volume keys on the side

of the headset base to adjust the

speaking volume when on a call

(page 31).

CORDED HANDSET CONNECTED/

YES/NO

Choose the setting based on whether

you have connected to a corded

handset (page 12 or 13).

LIFTER

This jack is only used to connect an

AT&T handset lifter (model TL7100,

purchased separately).

(USB port)

Open the port cover to plug in the USB

cable for use with PC mode (page 15).

Quick reference guide - headset base

7

Getting started

Quick reference guide - headset base

TEL WALL JACK (red dot)

POWER jack (green dot)

CORDED PHONE CONNECTION

jack (blue dot)

This jack is only used to connect

the corded phone connection cable

(page 13).

Corded handset audio adjust switch

Use this switch to adjust the corded

handset audio when you have connected

the headset base to a corded telephone

(page 14).

8

Getting started

Installation

See pages 9-10

for easy instructions.

You must install and

charge the battery before

using the headset.

STOP!

Colored labels

The cords provided with your headset are attached with colored

labels to help you plug them into the correct jacks on the

headset base. Each jack on the headset base is labeled and

marked with a colored dot, allowing you to plug in the correct

cords by matching the colors.

Digital subscriber line (DSL)

If you subscribe to high-speed Internet service (DSL - digital

subscriber line) through your telephone line, you must install a

DSL filter between the telephone line cord and telephone wall

jack (see page 12, 13 or 15). The filter prevents noise and caller

ID problems caused by DSL interference. Please contact your DSL

service provider for more information about DSL filters.

For customer service or product information, visit our website at

www.telephones.att.com or call 1 (800) 222-3111.

In Canada, dial 1 (866) 288-4268.

Avoid placing the headset base too close to:

• Communication devices such as television sets, VCRs or other

cordless telephones.

• Excessive heat sources.

• Noise sources such as a window with traffic outside, motors,

microwave ovens, refrigerators or fluorescent lighting.

• Excessive dust sources such as a workshop or garage.

• Excessive moisture.

• Extremely low temperature.

• Mechanical vibration or shock such as on top of a washing

machine or work bench.

9

Getting started

Battery installation

The battery is permanently attached to the battery compartment

cover. Do not try to separate them from each other. After

installing the battery pack, charge it for at least 15 minutes.

You may be able to make and receive short calls. For optimal

performance, charge the headset battery for at least three hours

before use. When fully charged, the headset battery provides

approximately 12 hours of talk time or 5 days of standby time.

When the headset is not in use, recharge it by returning it to the

headset base.

NOTES:

Remove any headset attachment, except the earbud, before battery replacement.

To order a replacement battery (model BT191665), visit our website at

www.telephones.att.com or call 1 (800) 222-3111.

In Canada, dial 1 (866) 288-4268.

•

1. Insert the battery into the

battery compartment.

2. Press down on the battery until it

clicks into place.

10

Getting started

Headset base installation and battery charging

After installing the battery, charge the headset by placing it in

the magnetic charging mount, as shown below. The light turns

on when the headset is charging.

IMPORTANT INFORMATION

Use only the supplied rechargeable battery pack or replacement

battery pack (model BT191665). To order, visit our website at

www.telephones.att.com or call 1 (800) 222-3111.

In Canada, dial 1 (866) 288-4268.

Plug the small end of the headset base power adapter into

the POWER jack (green dot) at the back of the headset base.

Plug the large end into an electrical outlet not controlled by a

wall switch.

1.

The magnet holds the top

of the headset in place.

The light turns on.

3.

Magnetic

charging

mount

Insert the headset into the

magnetic charging mount.

2.

11

Getting started

Headset base installation

Installation options

There are three installation options, as described below.

Option 1: Connect the headset to a telephone wall jack through

the line splitter provided (see page 12).

Option 2: Connect the headset to a corded phone using the

corded phone connection cable provided (see pages 13-14).

Option 3: Connect the headset to your computer using the USB

cable provided for VoIP calls, and to the telephone wall jack

using a telephone line cord for landline calls (see pages 15-

17). Make sure you install the AT&T Softphone Call Manager

on your computer using the CD-ROM provided in the package.

You may also visit www.telephones.att.com/downloads

to download and install the software. For installation and

operation instructions of the software, refer to the Installation

and Operation Guide which can also be found in the CD-ROM

provided or the web site stated above.

12

Getting started

NOTE: The headset base and headset do not have external ringers. When

you receive calls, the headset earpiece rings. If you have telephones

connected to the same telephone line as the headset base, you can rely on

the ringers of those telephones to alert you to incoming calls.

Plug one end of the

telephone line cord into

the TEL WALL JACK

(red dot) at the back of

the headset base.

•

A DSL filter (not included) is

required if you have DSL

high-speed Internet service.

The DSL filter must be plugged

into a telephone wall jack.

Telephone line cord

Plug the other end of the

telephone line cord into

the line splitter.

•

Line splitter

Corded or

cordless phone

Plug the line splitter into

the telephone wall jack

(or a DSL filter if you

subscribe to DSL Internet

service).

•

Connect another

telephone line

cord between the

telephone and the

line splitter.

•

Use the attached

fastener to bundle

all line cords neatly.

•

Headset base installation

Option 1: Connect the headset to a telephone wall jack

Make sure the CORDED HANDSET

CONNECTED switch on the right side of the

headset base is set to NO.

Connect the line cords, as shown below.

Use the included line splitter to connect the

headset base and your telephone to the

same telephone wall jack.

1.

2.

13

Getting started

Headset base installation

Option 2: Connect the headset to a corded phone

Make sure the CORDED HANDSET

CONNECTED switch on the right side of the

headset base is set to YES.

Connect the line cords, as shown below.

Use the included corded phone connection

cable to connect the headset base to your

corded telephone.

1.

2.

Plug one end of the

corded phone connection

cable into the CORDED

PHONE CONNECTION

jack (blue dot) at the back

of the headset base.

•

A DSL filter (not

included) is required

if you have DSL

high-speed Internet

service. The DSL filter

must be plugged into

a telephone wall jack.

Unplug the curly

handset cord from

the handset jack

on the corded

phone and plug

it into the jack on

the corded phone

connection cable.

•

Corded phone

Plug the other end

of the corded phone

connection cable into

the handset jack on

your corded phone.

•

Use the attached

fastener to bundle

all line cords neatly.

•

La page charge ...

AT&T TL7910 Manuel utilisateur

AT&T TL7910 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents