AT&T TL7912 Manuel utilisateur

User’s manual

TL7912

DECT 6.0 cordless headset

and handset lifter

Congratulations

on your purchase of this AT&T product.

Unify your everyday business communications with the AT&T

TL7912 DECT 6.0 Cordless Headset and Handset Lifter. Whether

you want to connect directly to your corded telephone,

telephone line or computer, you can with the TL7912 headset.

Control costs and support your mobile workforce with

connectivity to Voice over IP (VoIP) services like

Skype® and

Microsoft Lync®

. It comes with the TL7100 Handset Lifter, making

it convenient to answer and end calls right from the headset.

A magnetic charger in the cradle ensures the headset fits and

charges securely—so you’ll never run out of battery during long

calls. With up to 12 hours of hands-free talk time and a range of

up to 500 feet, you’re free to work wherever your work is.

Before using this AT&T product, please read the

Important safety information section on pages 62-64 of this

manual. Please thoroughly read this user’s manual for all the

feature operations and troubleshooting information necessary to

install and operate your new AT&T product. You can also visit our

website at www.telephones.att.com or call

1 (800) 222-3111. In Canada, dial 1 (866) 288-4268.

This telephone meets the California Energy Commission

regulations for energy consumption. Your telephone is set up to

comply with the energy-conserving standards right out of the

box. No further action is necessary.

Visit

www.telephones.att.com/headsets for a complete

list of AT&T phones that have been tested and found to be

compatible with the TL7912.

Skype

®

and Microsoft Lync

®

are registered trademarks of Microsoft Corporation.

the AT&T logo are trademarks of AT&T Intellectual Property licensed to

Advanced American Telephones, San Antonio, TX 78219. Printed in China.

Model number: TL7912

Type: DECT 6.0 cordless headset and handset lifter

Serial number:

Purchase date:

Place of purchase:

Both the model and serial numbers of your AT&T product can be

found on the bottom of the headset base and lifter.

Save your sales receipt and original packaging in case it is

necessary to return this product for warranty service.

Telephones identified with this logo have reduced noise and

interference when used with most T-coil equipped hearing

aids and cochlear implants. The TIA-1083 Compliant Logo is

a trademark of the Telecommunications Industry Association.

Used under license.

Parts checklist

Check to make sure the headset package includes the following

items. Save your sales receipt and original packaging in the

event warranty service is necessary.

User's manual

Quick start guide

TL7912

DECT 6.0 cordless headset

and handset lifter

Telephone line cord

Line splitter

Headset base

power adapter

Corded phone connection cable

Battery with battery

compartment cover attached

Cordless headset with

earbud attached

Headset base

User’s manual

TL7912

DECT 6.0 cordless headset

and handset lifter

Parts checklist

Auxiliary ring detectorLarge lifter padlifter pad pad Anti-slip pad

Handset lifterlifterUSB cableBehind the neck band

Three over the ear hooksFive earbuds Two over the head bands

CD-ROM

Table of contents

Getting started

Introduction ...................................... 1

Quick reference guide -

headset ........................................... 2

Headset lights ............................. 2

Headset alert tones .................. 4

Quick reference guide -

headset base ............................... 5

Headset base lights .................. 5

Quick reference guide -

handset lifter ............................... 8

STATUS light ...............................10

Installation ......................................11

Colored labels ...........................11

Digital subscriber line

(DSL) ...............................................11

Battery installation .....................12

Headset base installation

and battery charging ...........13

Headset base and handset

lifter installation .......................14

Installation options .................14

Option 1: Connect the

headset to a corded

phone ............................................15

Option 2: Connect the

headset to a corded phone

and computer ............................17

Option 3: Connect the

headset to a telephone

wall jack .......................................21

Adjust the corded handset

audio ..............................................22

Attach the lifter ........................23

Adjust the switch hook

presser position .......................24

Adjust the height of the

lifter arm ......................................24

Lifter adjustments and

testing ...........................................25

Installation of large lifter

pad (optional) ............................26

Installation of anti-slip pad

(optional) .....................................26

About internal and auxiliary

ring detectors ............................27

Install the auxiliary ring

detector ........................................27

Ring detector on/off ..............28

Adjust the sensitivity

level ...............................................28

Headset attachments ................29

Earbud ...........................................29

Over the ear hook ...................30

Over the head band ...............33

Behind the neck band ...........35

User’s manual

TL7912

DECT 6.0 cordless headset

and handset lifter

Operation

Headset operation ......................38

Power on/off the

headset .........................................38

PHONE mode and PC

mode .............................................38

PHONE mode.................................39

Make a call..................................39

Answer a call .............................39

End a call .....................................40

Voice command ........................40

Headset ringer ..........................40

Caller ID announce .................41

Temporary ringer

silencing .......................................41

Call waiting .................................41

Options while on calls ..............42

Volume control .........................42

Mute ...............................................43

Switching between PHONE

mode and PC mode ...............44

Appendix

Adding and registering

headsets ......................................45

Registration options ...............45

Register a headset to your

TL7912 headset base ............46

Register a headset to

an AT&T DECT cordless

telephone base ........................47

Deregistering headsets .............49

Deregister all headsets

from your TL7912 headset

base ................................................49

Troubleshooting ...........................50

Maintenance...................................61

Important safety

information .................................62

Safety information...................62

Especially about cordless

headsets ......................................63

Precautions for users

of implanted cardiac

pacemakers ................................64

For C-UL compliance .................65

Mesures de sécurité

importantes ................................65

FCC Part 68 and ACTA..............69

FCC Part 15 ....................................71

California Energy Commission

battery charging testing

instructions .................................72

Limited warranty ..........................73

Technical specifications ...........76

DECT 6.0 digital

technology ..................................76

Operating range .......................76

Extended range and

clarity ............................................76

Encrypted for added

security .........................................76

Index

Index ..................................................77

1

Introduction

The TL7912 is a cordless headset and base that allows you to

have handsfree phone conversations. The package also comes

with the TL7100 handset lifter, making it convenient to answer

and end calls right from the headset. It can be used in different

ways depending on your needs. Choose from the following three

options. Connect your TL7912:

To a traditional corded telephone (pages 15-16). Connect the

headset base to a corded telephone and install the lifter on

your corded telephone. You can use the headset to remotely

control the lifter for answering or hanging up a call.

To both a corded phone and computer (pages 17-20).

Connect the headset base to a corded telephone and install

the lifter on your corded telephone. Use the USB cable to

connect the headset base and your PC. You can make and

answer VoIP calls through Skype or Microsoft Lync, or landline

calls using the AT&T Softphone Call Manager. You can also

use the voice command feature to make or answer calls after

you have installed the AT&T Softphone Call Manager.

Install the AT&T Softphone Call Manager using the

CD-ROM provided in the package.

-OR-

Visit www.telephones.att.com/downloads to download

the software. Unzip and install the file after download.

For installation and operation instructions of the software, refer

to the Installation and Operation Guide which can also be

found in the CD-ROM provided or the web site stated above.

To a telephone line only (page 21). If you do not want to

install the lifter on the corded handset, you can simply connect

the headset to a telephone wall jack through the line splitter

provided. Use the telephones on the same telephone line to

make or answer calls. The headset is a supplementary device

that can join the calls.

•

Getting started

2

Getting started

light status

Red On when the headset battery is low and the headset

is charging in the headset base.

Flashes every 10 seconds to indicate the battery is

low when the headset is not in the headset base.

Flashes three times to indicate the headset is

powering off.

•

Blue On when a registered headset is charging in the

headset base.

Flashes three times to indicate the headset is

powering on.

Flashes twice every three seconds when the headset

is in use.

Flashes four times every four seconds when there is

an incoming call in PHONE mode.

Flashes every 10 seconds when a registered headset

in idle mode is out of the headset base.

•

Red and blue Flashes slowly when the headset is not registered.

Flashes quickly when the headset is trying to

register to a headset base.

•

Off The battery is dead.

No battery is installed.

The headset is powered off.

•

Quick reference guide - headset

Headset lights

(On/off button and light)

Press to make, answer or end a call

(pages 39-40).

3

Getting started

Quick reference guide - headset

VOL+/VOL-

Slide the volume switch

to the right or left to

adjust the headset

ringer volume while

in idle mode (page 40),

or the listening volume

while on a call

(page 42).

Earpiece

Microphone

The microphone

incorporates noise

canceling technology

for clearer calls.

FLASH

Press to answer an

incoming call when

you receive a call

waiting alert during a

call (page 41).

Battery with cover

attached

Remove to replace the

battery.

MUTE/VOICE

Press to mute the

microphone during a call

(page 43).

Press to mute the ringer in

the earpiece when there is

an incoming call (page 41).

Press to initiate the voice

command feature when in

idle mode (page 40).

4

Getting started

One long beep The headset is ready to take your voice

command. (You have to install the AT&T

Softphone Call Manager before using the

voice command feature. For installation and

operation instructions of the software, refer

to the Installation and Operation Guide

which can be found in the CD-ROM in the

package. You may also visit

www.telephones.att.com/

downloads to download it.)

•

One short beep every

30 seconds

The microphone is muted. •

Two beeps Error alert tone.

The speaking volume has reached its highest

or lowest setting.

Any key is pressed while the headset is out

of range.

•

Two low beeps Call waiting alert tone.•

Two rapid beeps

every 20 seconds

Low battery warning.•

Three rising beeps A conference call has started.•

Three rapid beeps

every 20 seconds

The headset is out of range.

The headset is not yet registered.

•

Three rapid beeps The headset is powering on or off.•

Quick reference guide - headset

Headset alert tones

5

Getting started

Quick reference guide - headset base

Magnetic charging mount

Place the headset here

for charging.

MUTE (light)

PAIR

Use to initiate headset

registration or deregistration.

PHONE (mode

button and light)

PC (mode button

and light)

MUTE

(Red)

On when you are registering a headset.

Flashes when a call is muted.

Flashes when you are deregistering headset(s) from the

headset base.

•

PHONE

(Blue)

On when PHONE mode is selected as the default mode

on the idle headset base.

Flashes four times every four seconds when there is an

incoming call.

Flashes twice every three seconds when the headset is in

use in PHONE mode.

Flashes slowly when a call is on hold in PHONE mode.

•

PC

(Blue)

On when PC mode is selected as the default mode on

the idle headset base.

Flashes twice every three seconds when the headset is in

use in PC mode.

Flashes slowly when a call is on hold in PC mode.

•

Headset base lights

6

Getting started

Quick reference guide - headset base

VOLUME /MICROPHONE

Press the volume keys on the side

of the headset base to adjust the

speaking volume when on a call

(page 42).

CORDED HANDSET CONNECTED/

YES/NO

Choose the setting based on whether

you have connected to a corded

handset (page 16, 18 or 21).

LIFTER

This jack is only used to connect an

AT&T handset lifter (model TL7100).

(USB port)

Open the port cover to plug in the

USB cable for use with PC mode

(pages 17-18).

7

Getting started

Quick reference guide - headset base

TEL WALL JACK (red dot)

POWER jack (green dot)

CORDED PHONE CONNECTION

jack (blue dot)

This jack is only used to connect

the corded phone connection cable

(page 15 or 17).

Corded handset audio adjust switch

Use this switch to adjust the corded

handset audio when you have connected

the headset base to a corded telephone

(page 22).

8

Getting started

Switch hook presser

When the CORDED HANDSET CONNECTED

switch is set to YES, pressing on the

headset raises or lowers the switch

hook presser.

Lifter control cable

Plug this cable into the LIFTER jack on

the headset base.

RING DETECT jack

Plug in the auxiliary ring

detector (page 27).

ADJUST LIFTER knob

Adjusts the height of the lifter arm (page 24).

Lifter arm

Holds the corded telephone handset.

Quick reference guide - handset lifter

SENSOR ADJ knob

Adjusts the sensitivity of the ring detector (page 28).

9

Getting started

Small lifter pad

Holds the earpiece of the corded telephone

handset.

Adhesive tape

Remove the protective strips before

attaching the lifter to the telephone base.

STATUS light

On in red when the ring detector is off (page 10).

On in blue when the ring detector is on and

the headset is not in use (page 10).

Flashes in blue four times every three seconds

when the ring detector detects an incoming

call (page 10).

Flashes in blue slowly when the switch hook

presser is raised and you are on a call

(page 10).

Quick reference guide - handset lifter

Internal ring detector

Detects the telephone ringer and sends a

ring tone to the headset earpiece.

RING ON/OFF

Press to turn the ring detector on or off. When the ring detector is

off, the cordless headset does not ring (page 28).

Switch hook presser adjustment knob

Adjusts the position of the switch hook presser

(page 24).

Front view

Back view

10

Getting started

STATUS light

Quick reference guide - handset lifter

Red On when the headset is not in use and the ring detector is

turned off.

Flashes slowly when the headset is in use and the ring

detector is turned off.

•

Blue On when the headset is not in use and the ring detector

is turned on.

Flashes four times every three seconds when the ring

detector detects an incoming call.

Flashes slowly when the headset is in use and the ring

detector is turned on.

•

Off The headset base does not have power.

The lifter control cable is not plugged into the LIFTER jack

on the headset base.

•

11

Getting started

Installation

See pages 12-13

for easy instructions.

You must install and

charge the battery before

using the headset.

STOP!

Colored labels

The cords have colored labels that guide you to plug them into

the correct headset base jacks. The back of the headset base

has color-coded dots and the names of the jacks above them

that correspond to the colored labels on the cords.

Digital subscriber line (DSL)

If you subscribe to high-speed Internet service (DSL - digital

subscriber line) through your telephone line, you must install a

DSL filter between the telephone line cord and telephone wall

jack (see page 15, 17 or 21). The filter prevents noise and caller

ID problems caused by DSL interference. Please contact your DSL

service provider for more information about DSL filters.

For customer service or product information, visit our website at

www.telephones.att.com or call 1 (800) 222-3111.

In Canada, dial 1 (866) 288-4268.

Avoid placing the headset base too close to:

• Communication devices such as television sets, VCRs or other

cordless telephones.

• Excessive heat sources.

• Noise sources such as a window with traffic outside, motors,

microwave ovens, refrigerators or fluorescent lighting.

• Excessive dust sources such as a workshop or garage.

• Excessive moisture.

• Extremely low temperature.

• Mechanical vibration or shock such as on top of a washing

machine or work bench.

12

Getting started

Battery installation

The battery is permanently attached to the battery compartment

cover. Do not try to separate them from each other. After

installing the battery pack, charge it for at least 15 minutes.

You may be able to make and receive short calls. For optimal

performance, charge the headset battery for at least three hours

before use. When fully charged, the headset battery provides

approximately 12 hours of talk time or 5 days of standby time.

When the headset is not in use, recharge by returning it to the

headset base.

NOTES:

Remove any headset attachment (earbud excluded) before battery replacement.

To order a replacement battery pack (model BT191665), visit our website at

www.telephones.att.com or call 1 (800) 222-3111.

In Canada, dial 1 (866) 288-4268.

•

1. Insert the battery pack into the

battery compartment.

2. Press down on the battery pack

until it clicks into place.

13

Getting started

Headset base installation and battery charging

After installing the battery, charge the headset by placing it in

the magnetic charging mount, as shown below. The light turns

on when the headset is charging.

IMPORTANT INFORMATION

Use only the supplied rechargeable battery pack or replacement

battery pack (model BT191665). To order, visit our website at

www.telephones.att.com or call 1 (800) 222-3111.

In Canada, dial 1 (866) 288-4268.

Plug the small end of the headset base power adapter into

the POWER jack (green dot) at the back of the headset base.

Plug the large end into an electrical outlet not controlled by a

wall switch.

1.

The magnet holds the top

of the headset in place.

The light turns on.

3.

Magnetic

charging

mount

Insert the headset into the

magnetic charging mount.

2.

La page charge ...

AT&T TL7912 Manuel utilisateur

AT&T TL7912 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents