AT&T TL7812 Manuel utilisateur

Catégorie
Répondeurs
Taper
Manuel utilisateur
User’s manual
TL7812
DECT 6.0 cordless headset
and handset lifter
Congratulations
on your purchase of this AT&T product.
Unify your everyday business communications with the AT&T
TL7812 DECT 6.0 Cordless Headset and Handset Lifter. Whether
you want to connect directly to your corded telephone,
telephone line or computer, you can with the TL7812 headset.
Control costs and support your mobile workforce with
connectivity to Voice over IP (VoIP) services like
Skype and
Microsoft Lync
. It comes with the TL7100 Handset Lifter, making
it convenient to answer and end calls right from the headset.
A magnetic charger in the cradle ensures the headset fits and
charges securely—so you’ll never run out of battery during long
calls. With up to 12 hours of hands-free talk time and a range of
up to 500 feet, you’re free to work wherever your work is.
Before using this AT&T product, please read the
Important safety information section on pages 61-63 of this
manual. Please thoroughly read this user’s manual for all the
feature operations and troubleshooting information necessary to
install and operate your new AT&T product. You can also visit our
website at www.telephones.att.com/smb or call
1 (800) 222-3111. In Canada, dial 1 (866) 288-4268.
This telephone meets the California Energy Commission
regulations for energy consumption. Your telephone is set up to
comply with the energy-conserving standards right out of the
box. No further action is necessary.
Visit
www.smbtelephones.att.com/compatibility-finder
for a complete list of AT&T phones that have been tested and
found to be compatible with the TL7812.
Skype and Microsoft Lync are registered trademarks of Microsoft Corporation.
© 2012-2016 Advanced American Telephones. All Rights Reserved. AT&T and
the AT&T logo are trademarks of AT&T Intellectual Property licensed to
Advanced American Telephones, San Antonio, TX 78219. Printed in China.
Model number: TL7812
Type: DECT 6.0 cordless headset and handset lifter
Serial number:
Purchase date:
Place of purchase:
Both the model and serial numbers of your AT&T product can be
found on the bottom of the headset base and lifter.
Save your sales receipt and original packaging in case it is
necessary to return this product for warranty service.
Telephones identified with this logo have reduced noise and
interference when used with most T-coil equipped hearing
aids and cochlear implants. The TIA-1083 Compliant Logo is
a trademark of the Telecommunications Industry Association.
Used under license.
Parts checklist
Check to make sure the headset package includes the following
items. Save your sales receipt and original packaging in the
event warranty service is necessary.
User's manual
Quick start guide
Telephone line cord
Line splitter
Headset base
power adapter
Corded phone connection cable
Battery with battery
compartment cover attached
Cordless headset with
earbud attached
Headset base
Quick start guide
TL7812
DECT 6.0 cordless headset
and handset lifter
User’s manual
TL7812
DECT 6.0 cordless headset
and handset lifter
Parts checklist
Auxiliary ring detectorLarge lifter padlifter pad pad Anti-slip pad
Handset lifterlifterUSB cableBehind the neck band
Three over the ear hooksFive earbuds Two over the head bands
Optional accessory
This headset system can be expanded by registering a TL7800
accessory headset (sold separately) to it. The TL7800 includes an
expansion headset and a headset charger (up to two headsets
can be used with the same headset base).
For more information about the product, visit our website at
www.telephones.att.com/smb
TL7800
User’s manual
TL7812
DECT 6.0 cordless headset
and handset lifter
Table of contents
Getting started
Introduction ...................................... 1
Quick reference guide -
headset ........................................... 2
Headset lights ............................. 2
Headset alert tones .................. 4
Quick reference guide -
headset base ............................... 5
Headset base lights .................. 5
Quick reference guide -
handset lifter ............................... 8
STATUS light ...............................10
Installation ......................................11
Colored labels ...........................11
Digital subscriber line
(DSL) ...............................................11
Battery installation .....................12
Headset base installation
and battery charging ...........13
Headset base and handset
lifter installation .......................14
Installation options .................14
Option 1: Connect the
headset to a
corded phone ............................15
Option 2: Connect the
headset to a corded
phone and computer .............17
Option 3: Connect the
headset to a telephone
wall jack .......................................20
Adjust the corded
handset audio ...........................21
Attach the lifter ........................22
Adjust the switch hook
presser position .......................23
Adjust the height of
the lifter arm .............................23
Lifter adjustments and
testing ...........................................24
Installation of large
lifter pad (optional) ................25
Installation of anti-slip
pad (optional) ............................25
About internal and auxiliary
ring detectors ............................26
Install the auxiliary ring
detector ........................................26
Ring detector on/off ..............27
Adjust the sensitivity level ...27
Headset attachments ................28
Earbud ...........................................28
Over the ear hook ...................29
Over the head band ...............32
Behind the neck band ...........34
Operation
Headset operation ......................37
Power on/off the
headset .........................................37
PHONE mode and
PC mode ......................................37
PHONE mode.................................38
Make a call..................................38
Answer a call .............................38
End a call .....................................39
Headset ringer ..........................39
Temporary ringer
silencing .......................................40
Call waiting .................................40
Options while on calls ..............41
Volume control .........................41
Mute ...............................................42
Multiple headsets use ...........42
Switching between PHONE
mode and PC mode ...............43
Appendix
Adding and registering
headsets ......................................44
Registration options ...............44
Register a headset to your
TL7812 headset base ............45
Register a headset to
an AT&T DECT cordless
telephone base ........................46
Deregistering headsets .............48
Deregister all headsets
from your TL7812
headset base .............................48
Troubleshooting ...........................49
Maintenance...................................60
Important safety
information .................................61
Safety information...................61
Especially about cordless
headsets ......................................62
Precautions for users
of implanted cardiac
pacemakers ................................63
Pacemaker patients ................63
For C-UL compliance .................64
Mesures de sécurité
importantes ................................64
FCC Part 68 and ACTA..............68
FCC Part 15 ....................................70
California Energy Commission
battery charging testing
instructions .................................71
Limited warranty ..........................72
Technical specifications ...........75
DECT 6.0 digital
technology ..................................75
Operating range .......................75
Extended range and
clarity ............................................75
Encrypted for added
security .........................................75
Index
Index ..................................................76
1
Introduction
The TL7812 is a cordless headset and base that allows you to
have handsfree phone conversations. The package also comes
with the TL7100 handset lifter, making it convenient to answer
and end calls right from the headset. It can be used in different
ways depending on your needs. Choose from the following three
options. Connect your TL7812:
To a traditional corded telephone (pages 15-16). Connect the
headset base to a corded telephone and install the lifter on
your corded telephone. You can use the headset to remotely
control the lifter for answering or hanging up a call.
To both a corded phone and computer (pages 17-19).
Connect the headset base to a corded telephone and install
the lifter on your corded telephone. Use the USB cable to
connect the headset base and your PC. You can make and
answer VoIP calls through Skype or Microsoft Lync, or landline
calls using the AT&T Softphone Call Manager.
Visit www.smbtelephones.att.com/downloads
to download the AT&T Softphone Call Manager. For
installation and operation instructions of the software, refer
to the Installation and Operation Guide which can also be
downloaded at
www.smbtelephones.att.com/downloads.
To a telephone line only (page 20). If you do not want to
install the lifter on the corded handset, you can simply connect
the headset to a telephone wall jack through the line splitter
provided. Use the telephones on the same telephone line to
make or answer calls. The headset is a supplementary device
that can join the calls.
Getting started
2
Getting started
light status
Red On when the headset is charging in the
headset base.
Flashes every 10 seconds to indicate the battery is
low when the headset is not in the headset base.
Flashes three times to indicate the headset is
powering off.
Blue On when a fully charged and registered headset is
in the headset base.
Flashes three times to indicate the headset is
powering on.
Flashes twice every three seconds when the headset
is in use.
Flashes four times every four seconds when there is
an incoming call in PHONE mode.
Flashes every 10 seconds when a fully charged
and registered headset in idle mode is out of the
headset base.
Red and blue Flashes slowly when the headset is not registered.
Flashes quickly when the headset is trying to
register to a headset base.
Off The battery is dead.
No battery is installed.
The headset is powered off.
Quick reference guide - headset
Headset lights
(On/off button and light)
Press to make, answer or end a call
(pages 38-39).
3
Getting started
Quick reference guide - headset
VOL+/VOL-
Slide the volume switch
to the right or left to
adjust the headset
ringer volume while
in idle mode (page 39),
or the listening volume
while on a call
(page 41).
Earpiece
Microphone
The microphone
incorporates noise
canceling technology
for clearer calls.
FLASH
Press to answer an
incoming call when you
receive a call waiting alert
during a call (page 40).
Battery with cover
attached
Remove to replace the
battery.
MUTE
Press to mute the
microphone during a call
(page 42).
Press to mute the ringer in
the earpiece when there is
an incoming call (page 40).
4
Getting started
One short beep every
30 seconds
The microphone is muted.
Two beeps Error alert tone.
The ringer volume has reached its lowest
setting.
The listening volume has reached its highest
or lowest setting.
The speaking volume has reached its highest
or lowest setting.
Any key is pressed while the headset is out
of range.
Two low beeps Call waiting alert tone.
Two rapid beeps
every 20 seconds
Low battery warning.
Three rising beeps A conference call has started.
Three rapid beeps
every 20 seconds
The headset is out of range.
The headset is not yet registered.
Three rapid beeps The headset is powering on or off.
Quick reference guide - headset
Headset alert tones
5
Getting started
Quick reference guide - headset base
Magnetic charging mount
Place the headset here
for charging.
MUTE (light)
PAIR
Use to initiate headset
registration or deregistration.
PHONE (mode
button and light)
PC (mode button
and light)
MUTE
(Red)
On when you are registering a headset.
Flashes when a call is muted.
Flashes when you are deregistering headset(s) from the
headset base.
PHONE
(Blue)
On when PHONE mode is selected as the default mode
on the idle headset base.
Flashes four times every four seconds when there is an
incoming call.
Flashes twice every three seconds when the headset is in
use in PHONE mode.
Flashes slowly when a call is on hold in PHONE mode.
PC
(Blue)
On when PC mode is selected as the default mode on
the idle headset base.
Flashes twice every three seconds when the headset is in
use in PC mode.
Flashes slowly when a call is on hold in PC mode.
Headset base lights
6
Getting started
Quick reference guide - headset base
VOLUME /MICROPHONE
Press the volume keys on the side
of the headset base to adjust the
speaking volume when on a call
(page 41).
CORDED HANDSET CONNECTED/
YES/NO
Choose the setting based on whether
you have connected to a corded
handset (page 16, 18 or 20).
LIFTER
This jack is only used to connect an
AT&T handset lifter (model TL7100,
purchased separately).
(USB port)
Open the port cover to plug in the
USB cable for use with PC mode
(pages 17-18).
7
Getting started
Quick reference guide - headset base
TEL WALL JACK (red dot)
POWER jack (green dot)
CORDED PHONE CONNECTION
jack (blue dot)
This jack is only used to connect
the corded phone connection cable
(page 15 or 17).
Corded handset audio adjust switch
Use this switch to adjust the corded
handset audio when you have connected
the headset base to a corded telephone
(page 21).
8
Getting started
Switch hook presser
When the CORDED HANDSET CONNECTED
switch is set to YES, pressing on the
headset raises or lowers the switch
hook presser.
Lifter control cable
Plug this cable into the LIFTER jack on
the headset base.
RING DETECT jack
Plug in the auxiliary ring
detector (page 26).
ADJUST LIFTER knob
Adjusts the height of the lifter arm (page 23).
Lifter arm
Holds the corded telephone handset.
Quick reference guide - handset lifter
SENSOR ADJ knob
Adjusts the sensitivity of the ring detector (page 27).
9
Getting started
Small lifter pad
Holds the earpiece of the corded telephone
handset.
Adhesive tape
Remove the protective strips before
attaching the lifter to the telephone base.
STATUS light
On in red when the ring detector is off (page 10).
On in blue when the ring detector is on and
the headset is not in use (page 10).
Flashes in blue four times every three seconds
when the ring detector detects an incoming
call (page 10).
Flashes in blue slowly when the switch hook
presser is raised and you are on a call
(page 10).
Quick reference guide - handset lifter
Internal ring detector
Detects the telephone ringer and sends a
ring tone to the headset earpiece.
RING ON/OFF
Press to turn the ring detector on or off. When the ring detector is
off, the cordless headset does not ring (page 27).
Switch hook presser adjustment knob
Adjusts the position of the switch hook presser
(page 23).
Front view
Back view
10
Getting started
STATUS light
Quick reference guide - handset lifter
Red On when the headset is not in use and the ring detector is
turned off.
Flashes slowly when the headset is in use and the ring
detector is turned off.
Blue On when the headset is not in use and the ring detector
is turned on.
Flashes four times every three seconds when the ring
detector detects an incoming call.
Flashes slowly when the headset is in use and the ring
detector is turned on.
Off The headset base does not have power.
The lifter control cable is not plugged into the LIFTER jack
on the headset base.
11
Getting started
Installation
See pages 12-13
for easy instructions.
You must install and
charge the battery before
using the headset.
Colored labels
The cords have colored labels that guide you to plug them into
the correct headset base jacks. The back of the headset base
has color-coded dots and the names of the jacks above them
that correspond to the colored labels on the cords.
Digital subscriber line (DSL)
If you subscribe to high-speed Internet service (DSL - digital
subscriber line) through your telephone line, you must install a
DSL filter between the telephone line cord and telephone wall
jack (see page 15, 17 or 20). The filter prevents noise and caller
ID problems caused by DSL interference. Please contact your DSL
service provider for more information about DSL filters.
For customer service or product information, visit our website at
www.telephones.att.com/smb or call
1 (800) 222-3111. In Canada, dial 1 (866) 288-4268.
Avoid placing the headset base too close to:
• Communication devices such as television sets, VCRs or other
cordless telephones.
• Excessive heat sources.
• Noise sources such as a window with traffic outside, motors,
microwave ovens, refrigerators or fluorescent lighting.
• Excessive dust sources such as a workshop or garage.
• Excessive moisture.
• Extremely low temperature.
• Mechanical vibration or shock such as on top of a washing
machine or work bench.
12
Getting started
Battery installation
The battery is permanently attached to the battery compartment
cover. Do not try to separate them from each other. After
installing the battery pack, charge it for at least 15 minutes.
You may be able to make and receive short calls. For optimal
performance, charge the headset battery for at least three hours
before use. When fully charged, the headset battery provides
approximately 12 hours of talk time or 5 days of standby time.
When the headset is not in use, recharge by returning it to the
headset base.
NOTES:
Remove any headset attachment (earbud excluded) before battery replacement.
To order a replacement battery pack (model BT191665), visit our website at
www.telephones.att.com/smb or call
1 (800) 222-3111. In Canada, dial 1 (866) 288-4268.
1. Insert the battery pack into the
battery compartment.
2. Press down on the battery pack
until it clicks into place.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86

AT&T TL7812 Manuel utilisateur

Catégorie
Répondeurs
Taper
Manuel utilisateur

dans d''autres langues