VTech IS6200 Manuel utilisateur

Marque: VTech

Modèle: IS6200

Catégorie: Téléphones

Taper: Manuel utilisateur

For VTech models:

Press and hold /FIND HANDSET on the

telephone base for about four seconds until

the red IN USE light turns on. Then, release

the button.

Immediately place the headset in the

headset charger. It takes about 60 seconds

to complete the registration process. The red

IN USE light on the telephone base turns off.

The ON / OFF light on the headset turns red

when it is registered and charged.

Lift the headset, then press ON / OFF key

on the headset. If you hear a dial tone, the

registration was successful.

For VTech ErisBusinessSystemTM:

Press MENU on the console or deskset.

Press or to scroll to Registration, and

press SELECT or /SKIP.

Press or to scroll to select DECT

Headset, and then press SELECT or

/SKIP. The console or deskset screen

displays Registering DECT Headset...(Put

DECT Headset in charger).

Place the headset in the charger. The

registration takes up to 60 seconds to

complete. When the registration is complete,

the console or deskset screen displays

DECT Headset registered.

Lift the headset, then press ON / OFF key

on the headset. If you hear a dial tone, the

registration was successful.

For VTech CM series business phone

system:

Press MENU on the console.

Scroll to Registration, then press SELECT.

Press SELECT again to select Register Ext.

Place the headset in the charger. It may

take up to 60 seconds to complete the

registration. The console shows HDST/SPK

X registered. (X represents the extension

number 9 to 1) and beeps when the

registration is successful.

The console shows Link HDST/SPK X to

extension?. If you want to link the headset

with an extension, scroll to Yes. Otherwise,

choose No and then skip to Step 7. Press

SELECT to confirm.

Scroll to select a desired extension to be

linked with the headset or speakerphone.

Press SELECT to confirm.

Lift the headset, then press ON / OFF key

on the headset. If you hear a dial tone, the

registration was successful. If you linked the

headset with an extension, the extension

screen displays the extension number along

with the line number it is using.

For AT&T models with

/HANDSET LOCATOR button on the

telephone base:

Press and hold the /HANDSET LOCATOR

button on the telephone base for about four

seconds until the IN USE light turns on, or

the base displays Registering... Please

wait. Then, release the button.

Immediately place the headset in the

headset charger. The ON / OFF light on the

headset flashes quickly and alternately in

red and blue to indicate the registration is in

progress. This may take up to five minutes to

complete. The ON / OFF light on the headset

turns red when it is registered and charged.

You hear a confirmation tone.

Lift the headset, then press ON / OFF key

on the headset. If you hear a dial tone, the

registration was successful.

For AT&T models without

/HANDSET LOCATOR button on the

telephone base:

Press MENU on the telephone base when

idle.

Scroll to Settings, and then press SELECT.

Scroll to Registration, and then press

SELECT. The base displays Registering...

Please wait.

Follow Steps 2 and 3 under For AT&T

models with /HANDSET LOCATOR

button on the telephone base section.

For AT&T Synapse® business phone

system:

Press MENU, 2, and then 6 on the telephone

base when idle. Menu Cordless Headset

appears.

Press Register. The base displays

Registering in Progress....

Follow Steps 2 and 3 under For AT&T

models with /HANDSET LOCATOR

button on the telephone base section.

For AT&T Syn248® business phone

system:

Press MENU, 2, and then 5 on the

telephone base when idle. Menu Cordless

Headset Registration appears.

Press Register. The base displays

Registering in Progress....

Follow Steps 2 and 3 under For AT&T

models with /HANDSET LOCATOR

button on the telephone base section.

For AT&T SynJ® business phone

system:

Press MENU on the telephone base when

idle.

Scroll to Registration, and then press

ENTER twice to select Register HS. The

telephone base shows Registering new

device.... It takes up to 60 seconds to

complete the registration.

Place the headset in the headset charger.

The telephone base shows Cordless

headset registered and beeps when the

registration is successful.

Lift the headset, then press ON / OFF key on

the headset. If you hear a dial tone and the

extension 0 icon also appears on the

telephone base, the registration was

successful. If you have a dial tone but an

extension number other than 0 displays on

the telephone base, the headset is

registered as a handset and will not function

properly. If this is the case, you must

deregister and start over. See Replace a

headset section.

Replace a headset

If you want to replace a headset or reassign

the designated headset number of a registered

headset, you must deregister all handsets

and headsets that are registered to the same

telephone base. Then register each handset and

headset individually.

To deregister all headsets:

To deregister all headsets from the telephone

base, follow the instructions in the user’s manual

of your telephone system, or visit our website

at www.vtechphones.com or AT&T’s website at

www.telephones.att.com.

This operation will deregister all the

DECT handsets, headsets, and cordless

speakerphones, regardless of their battery

status and whether they are within range or

out-of-range.

If the deregistration process is successful, you

hear “Not registered” when you press ON/OFF

key on the headset. If the deregistration fails,

you may need to reset the telephone or headset,

and then try again.

NOTE

You cannot deregister a headset if any system

handset or headset is in use.

To reset:

Unplug the power from the telephone base,

then plug it back in.

•

Position the headset

There are four earbuds and four earhooks

provided. One earbud and one earhook have

been attached to the headset.

You can choose a suitable size of earbud,

earhook and an appropriate way to position your

headset.

Replace the pre-installed earbud and

earhook:

Hold both sides of the earbud. Twist and pull

the earbud until it separates from the earpiece.

Rotate the earhook to vertical direction and

then pull the earhook until it separates from the

headset.

Attach a earhook, and then a suitable earbud to

the headset until they fit into place.

To wear on the right ear:

To wear on the left ear:

4. Wrap the earhook with the sponge.

Adjust the headset to wear on the ear:

Hook the headset on your ear. Adjust the angle

of the headset until the microphone is pointing

towards your mouth. Firmly grip the headset

with one hand whenever adjusting the headset

microphone up or down.

•

Over the head band

To attach the head band to the headset:

Refer to Steps 1 and 2 in Replace the

pre-installed earbud and earhook section

to remove the earbud and earhook.

Attach the headset to the headband.

Rotate the headset to horizontal direction until it

clicks into place.

Adjust the head band to fit your head. Adjust

and rotate the angle of the headset until the

microphone is pointing towards your mouth.

To remove the head band from the

headset:

Hold the headset with one hand and the

head band with your other hand.

Rotate the headset to vertical direction and

the pull the headset until it separates form

the head band.

Using the headset

Make a call

Follow the instructions in your telephone

user’s manual for making calls.

Press ON/OFF key to join the call.

Answer a call

Press ON/OFF key to answer a call.

End a call

Press ON/OFF key or place the headset in

the headset charger.

•

Ringer

The headset does not have an external ringer.

When there is an incoming call, the headset

earpiece rings.

If you have telephones connected to the same

telephone line, you can rely on the ringers of

those telephones to alert you to incoming calls.

Volume

During a call, press VOL+ or VOL- on the

headset to adjust the listening volume.

Mute

The mute function allows you to hear the other

party but the other party cannot hear you.

During a call, press MUTE. The headset

announced “Mute on”.

Press MUTE again to resume the

conversation. The headset announced

“Mute off”.

Call waiting

When you subscribe to call waiting service from

your telephone service provider, you hear an

alert tone if there is an incoming call while you

are on another call.

Press FLASH to put the current call on hold

and take the new call.

Press FLASH to switch back and forth

between calls.

Multiple headset/handset use

Headset(s) and handset(s) on the same phone

line can join an outside call at the same time.

The number of headset(s) and handset(s) that

can join may be limited by your telephone

system. See your telephone user’s manual for

more information.

To share an outside call:

When a headset or handset is already on a

call, press ON/OFF key on another headset

to join the call.

To exit the call, press ON/OFF key again or

place the headset in the headset charger.

The call continues until all handsets and/or

headsets hang up.

•

Intercom call

Follow the instructions in your telephone user’s

manual for initiating an intercom call. When

there is an intercom call request from a cordless

telephone to a headset, the headset earpiece

rings if it is not in use.

To answer an intercom call:

Press ON/OFF key to answer the intercom

call.

To transfer a call to the headset:

During a call on the cordless handset or

telephone base, initiate an intercom call to

the headset. Press ON/OFF key on the

headset to answer the intercom call, and then

hang up the call on the cordless handset or

telephone base.

Operating range

This cordless headset operates with the

maximum power allowed by the Federal

Communications Commission (FCC). Even

so, this headset and telephone base can

communicate over only a certain distance - which

can vary with the locations of the telephone base

and headset, the weather, and the layout of your

home or ofﬁce.

If there is a call while the headset is out of range,

it may not ring, or if it does ring, the call may not

connect well when you press ON/OFF key on the

headset. Move closer to the telephone base, then

press ON/OFF key on the headset to answer the

call.

If the headset moves out of range during

a telephone conversation, there may be

interference.

To improve reception, move closer to the

telephone base.

•

General product care

Taking care of your headset

Your cordless headset contains sophisticated

electronic parts, so it must be treated with care.

Avoid rough treatment

Place the headset down gently. Save the original

packing materials to protect your headset if you

ever need to ship it.

Avoid water

Your headset can be damaged if it gets wet.

Do not use the headset outdoors in the rain,

or handle it with wet hands. Do not install the

headset charger near a sink, bathtub or shower.

Electrical storms

Electrical storms can sometimes cause power

surges harmful to electronic equipment. For your

own safety, take caution when using electrical

appliances during storms.

Cleaning your headset

Your headset has a durable plastic casing that

should retain its luster for many years. Clean it

only with a dry non-abrasive cloth. Do not use

dampened cloth or cleaning solvents of any kind.

Congratulations

on purchasing your new VTech product. Before

using this product, please read Important

safety instructions.

This abridged user’s manual provides you with

basic installation and use instructions. A limited

set of features are described in abbreviated form.

Please refer to the online User’s manual for a full

set of installation and operation instructions at

www.vtechphones.com.

What’s in the box

Your product package contains the following

items. Save your sales receipt and original

packaging in the event warranty service is

necessary.

Headset overview

1 – VOL+

• Increase the headset volume.

VOL-

• Decrease the headset volume.

Flash

• While on a call, press and hold to answer

an incoming call when you receive a call

waiting alert.

2 – ON / OFF light

• On when the headset is charging.

ON / OFF key

• Press to answer or end a call.

3 – Microphone

4 – MUTE

Press to activate the voice-controlled

application on your connected cell phone

when idle.

Mute the microphone during a call.

When there is an incoming call, press

to silence the ringer in the earpiece

temporarily.

5 – Earpiece

6 – Earhook

•

Charger overviewoverview

1 – Magnetic charging mount

• Place the headset for charging.

2 – Power jack

Lights and alert tones overview overview

Light status

Alert tones

Connect

NOTES

Use only the adapters provided.

Charge the battery provided with or identified for

use with this product only in accordance with the

instructions and limitations specified in this manual.

Connect the charger

•

Install the battery

Install the battery as shown below.

NOTES

Use only supplied battery.

If the headset will not be used for a long time,

remove the battery to prevent possible leakage.

Charge the battery

Place the headset in the charger to charge. The

LED light turns on.

NOTES

For best performance, keep the headset in the

telephone base or charger when not in use.

The battery is fully charged after 3 hours of

continuous charging.

When fully charged, the battery provides

approximately 4 hours of talk time or 48 hours of

standby time.

•

Before use

Add and register a headset

Before use, each newly purchased headset

(IS6200) must be registered to a VTech DS,

IS, LS, or SN series home cordless phone, a

VTech ErisBusinessSystemTM or CM series

business phone, an AT&T CL, CRL, CLP,

or TL series home cordless phone, or an

AT&T Synapse®, Syn248® or SynJ® business

phone. Visit www.vtechphones.com for a list of

compatible telephones.

The telephone base recognizes and counts a

headset the same as a handset. You can place

the headset charger anywhere you have an

available power outlet.

Refer to your telephone user’s manual for a

maximum number of headsets that you can

have the maximum number of handsets/

headsets registered, you need to follow the

deregistration information in your telephone

user’s manual before adding a new headset.

Before registering:

Place the non-registered headset in the

headset charger and allow it to charge for at

least 15 minutes before registration. Remove

the headset from the headset charger. The

LED light on the headset flashes slowly and

alternately in red and blue.

To register a headset to a telephone

base:

NOTES

You cannot register a headset if any other system

handset or headset is in use. You can only register

one headset to the telephone base at a time.

The headset must be deregistered before

registering it to another telephone system.

If the registration fails, you hear “Not registered”

when you press ON/OFF key on the headset. The

ON/OFF light on the headset flashes slowly and

alternately in red and blue. To reset the headset,

remove it from the headset charger and then place

it back into its charger. Try the registration process

again.

ErisBusinessSystem™ is a trademark of VTech

Communications, Inc.

Synapse®, Syn248® and SynJ® are trademarks of

Advanced American Telephones.

•

IS6200

DECT 6.0 accessory

cordless headset

Go to www.vtechphones.com

to register your product for

enhanced warranty support and

the latest VTech product news.

Telephones identified with this

logo have reduced noise and

interference when used with

most T-coil equipped hearing

aids and cochlear implants.

The TIA-1083 Compliant

Logo is a trademark of the

Telecommunications Industry

Association. Used under license.

User’s manual

Red On when the headset battery is

charging..

Flashes every 10 seconds when

the headset battery is low and

needs charging.

•

Blue Flashes twice every three

seconds when the headset is in

use.

Flashes every four seconds when

there is an incoming call.

Flashes every 10 seconds when

the headset is out of the headset

charger and has enough charge.

•

Red and blue Flashes slowly when the headset

is not registered.

Flashes quickly when the headset

is registering to a telephone base.

•

Off No battery is installed, or the

headset has run out of battery.

The headset is powered off.

•

Compatible with

Hearing Aid T-Coil

TIA-1083

User’s manual

One short

beep every

30 seconds

The microphone is muted.•

Two low

beeps

Call waiting alert tone.•

Three rising

beeps

A conference call has started.•

Frequently asked questions

The following are the questions most frequently

asked about the cordless headset. If you cannot

ﬁnd the answer to your question, visit our website

at www.vtechphones.com or call

1 (800) 595-9511 for customer service. In

Canada, go to www.vtechcanada.com or call

1 (800) 267-7377.

My headset does

not work at all.

Make sure the telephone line

cord is plugged firmly into

the telephone base and the

telephone wall jack..

Charge the headset in the

headset charger for up to three

hours.

Make sure the headset charger

power adapter is securely

plugged into an electrical outlet.

For optimum daily performance,

return the headset to the

headset charger after use.

Unplug the electrical power to

the telephone base. Wait for

approximately 15 seconds,

then plug it back in. Allow up

to one minute for the cordless

headset and telephone base to

synchronize.

Other electronic products such

as HAM radios and other DECT

phones can cause interference

with your cordless phone. Try

installing your phone as far away

as possible from these types of

electronic devices.

If the headset battery is

completely depleted, it may take

up to 15 minutes to charge the

headset before the headset has

enough charge to use for a short

time.

The headset battery may be

defective. Contact our customer

service for assistance.

I cannot dial out. You must use a telephone on

the same line to dial out. Once

you have dialed the number, you

can press ON/OFF key on the

headset to take the call. After

the headset is activated, you

can hang up the telephone from

which you dialed from.

If other telephones in your home

are having the same problem,

the problem is in your wiring

or telephone service. Contact

your telephone service provider

(charges may apply).

The other party

cannot hear my

voice during a call.

Make sure the mute feature is

not turned on during a call.

The headset does

not charge in the

headset charger.

Make sure the headset charger

power adapter is securely plugged

into an electrical outlet. For

optimum daily performance, return

the headset to the headset charger

after use.

Make sure the cordless headset

is placed in the headset charger

correctly. The headset ON/OFF

light should be on.

Unplug the headset charger and

then plug it back, then charge for

up to three hours.

If the cordless headset is in the

headset charger and the headset

ON/OFF light is not on, refer

to The ON/OFF light on the

headset is off while charging

below.

If the battery is completely

depleted, it may take up to 15

minutes to charge the headset

before it has enough charge to be

used for a short time. For optimum

daily performance, return the

cordless headset to the headset

charger when not in use.

The headset battery may be

defective. Contact our customer

service for assistance.

The ON/OFF light

on the headset is

off while charging

Make sure the headset charger

power adapter is correctly and

securely plugged in the electrical

outlet.

Make sure the headset is sitting

properly in the headset charger

to charge.

Clean the charging contacts on

the headset and headset charger

each month with a pencil eraser

or a dry non-abrasive fabric.

Unplug the headset charger

power adapter. Wait for 15

seconds before plugging it back

in.

My cordless

headset is not

performing

normally.

Make sure the power cord is

correctly and securely plugged

into the headset charger. Plug the

telephone base into a different

working electrical outlet not

controlled by a wall switch.

Move the cordless headset closer

to the telephone base. It may be

out of range.

Other electronic products such

as HAM radios and other DECT

phones can cause interference

with your cordless phone. Try

installing your phone as far away

as possible from these types of

electronic devices.

I cannot hear any

ring tone from the

cordless headset

when there is an

incoming call.

The headset does not have an

external ringer. The ring tone

can only be heard through the

headset earpiece.

Make sure the headset ringer

volume is not set to the lowest

level.

If you have pressed MUTE on

the cordless headset when it is

ringing, it mutes the ring tone

of the headset. The ring tone

resumes on the next call.

The headset may be too far from

the telephone base. Move it

closer to the telephone base.

You may have too many

extension phones on the

telephone line to allow all of

them to ring simultaneously.

Unplug some of them.

The layout of your home or office

may be limiting the operating

range. Try moving the telephone

base to another location,

preferably on a higher location.

If other telephones in your home

are having the same problem,

the problem is in the wiring or

telephone service. Contact your

telephone service provider.

Other electronic products such

as HAM radios and other DECT

phones can cause interference

with your cordless phone. Try

installing your phone as far away

as possible from these types of

electronic devices.

I cannot hear any

ring tone from the

cordless headset

when there is an

incoming call.

Test a working telephone at

the telephone wall jack. If

another telephone has the same

problem, there may be problem

with the telephone wall jack.

Contact your telephone service

provider.

The telephone line cord may

be defective. Install a new

telephone line cord.

There is

interference

during a telephone

conversation.

My calls fade out

when I am using

the cordless

headset.

The cordless headset may be

out of range. Move it closer to

the telephone base.

If you subscribe to high-

speed Internet service (digital

subscriber line - DSL) through

your telephone line, you must

install a DSL filter between

the telephone line cord and

the telephone wall jack. The

filter prevents noise and caller

ID problems caused by DSL

interference. Contact your

DSL service provider for more

information about DSL filters.

Appliances or other cordless

telephones plugged into the

same circuit as the telephone

base can cause interference.

Try moving the appliance or

telephone base to another outlet.

Other electronic products such

as HAM radios and other DECT

phones can cause interference

with your cordless phone. Try

installing your phone as far away

as possible from these types of

electronic devices.

If your telephone is plugged

in with a modem or a surge

protector, plug the telephone (or

modem/surge protector) into a

different location. If this doesn’t

solve the problem, relocate your

telephone or modem farther

apart from each other, or use a

different surge protector.

There is

interference

during a telephone

conversation.

My calls fade out

when I am using

the cordless

headset.

The location of your telephone

base can impact the

performance of your cordless

headset. For better reception,

install the telephone base in

a centralized location within

your home or office, away from

walls or other obstructions. In

many environments, relocating

the telephone base to a higher

location improves overall

performance.

Disconnect the telephone base

from the telephone wall jack

and plug in a corded telephone.

If calls are still not clear, the

problem is probably in the wiring

or telephone service. Contact

your telephone service provider

(charges may apply).

If other telephones in your home

are having the same problem,

the problem is in the wiring or

telephone service. Contact your

telephone service provider.

I hear other calls

when using my

cordless headset.

Disconnect the telephone base

from the telephone wall jack.

Plug in a different telephone.

If you still hear other calls, the

problem is probably in the wiring

or telephone service. Call your

telephone service provider.

I cannot register

the headset.

Only one headset can be

registered at a time. If you have

multiple headsets to register,

please follow the instructions on

Add and register a headset for

the first headset. Once a headset

has been successfully registered,

repeat the steps for each headset

that needs to be registered.

If you have already registered

the maximum numbers of

handsets and/or headsets that the

telephone system accommodates,

you need to follow the

deregistration instructions before

registering a headset. Refer to

Add and register a headset on

and Replace a headset section.

Make sure that all registered

handsets, registered headsets

and telephone base are in idle

mode when registering a headset.

Follow steps in Common cure

for electronic equipment, then

try again to register a headset.

I want to use my

cordless headset

with a different

telephone base.

You need to deregister the

headset from the current

telephone base and then register

it to the new telephone base.

Make sure the power cord

is securely plugged into the

telephone base. Use a working

electrical outlet not controlled by

a wall switch.

Reset your telephone by

unplugging the power adapter

from the telephone base.

Other electronic products such

as HAM radios and other DECT

phones can cause interference

with your cordless phone. Try

installing your phone as far away

as possible from these types of

electronic devices.

Common cure

for electronic

equipment.

If the unit is not responding

normally, put the cordless

headset in its charger. If it does

not respond, try the following (in

the order listed):

- Disconnect the power to the

telephone base.

- Wait a few minutes before

connecting power to the

telephone base.

- Remove and place the cordless

headset in its charger.

- Wait for the cordless headset to

synchronize with the telephone

base. Allow up to one minute for

this to take place.

Important safety instructions

When using your telephone equipment, basic

safety precautions should always be followed to

reduce the risk of fire, electric shock and injury,

including the following:

Read and understand all instructions.

Follow all warnings and instructions marked

on the product.

Unplug this product from the wall outlet

before cleaning. Do not use liquid or aerosol

cleaners. Use a damp cloth for cleaning.

Do not use this product near water such as

near a bath tub, wash bowl, kitchen sink,

laundry tub or swimming pool, or in a wet

basement or shower.

Do not place this product on an unstable

table, shelf, stand or other unstable surfaces.

Slots and openings in the back or bottom

of the telephone base and handset are

provided for ventilation. To protect them

from overheating, these openings must not

be blocked by placing the product on a soft

surface such as a bed, sofa or rug. This

product should never be placed near or

over a radiator or heat register. This product

should not be placed in any area where

proper ventilation is not provided.

This product should be operated only from

the type of power source indicated on the

marking label. If you are not sure of the

type of power supply in your home or office,

consult your dealer or local power company.

Do not allow anything to rest on the power

cord. Do not install this product where the

cord may be walked on.

Never push objects of any kind into this

product through the slots in the telephone

base or handset because they may touch

dangerous voltage points or create a short

circuit. Never spill liquid of any kind on the

product.

To reduce the risk of electric shock, do

not disassemble this product, but take it to

an authorized service facility. Opening or

removing parts of the telephone base or

handset other than specified access doors

may expose you to dangerous voltages

or other risks. Incorrect reassembling can

cause electric shock when the product is

subsequently used.

Do not overload wall outlets and extension

cords.

Unplug this product from the wall outlet and

refer servicing to an authorized service facility

under the following conditions:

When the power supply cord or plug is

damaged or frayed.

If liquid has been spilled onto the product.

If the product has been exposed to rain or

water.

10.

11.

12.

•

If the product does not operate normally

by following the operating instructions.

Adjust only those controls that are

covered by the operation instructions.

Improper adjustment of other controls

may result in damage and often requires

extensive work by an authorized

technician to restore the product to normal

operation.

If the product has been dropped and the

telephone base and/or handset has been

damaged.

If the product exhibits a distinct change in

performance.

13. Avoid using a telephone (other than cordless)

during an electrical storm. There is a remote

risk of electric shock from lightning.

14. Do not use the telephone to report a gas

leak in the vicinity of the leak. Under certain

circumstances, a spark may be created

when the adapter is plugged into the power

outlet, or when the handset is replaced in its

cradle. This is a common event associated

with the closing of any electrical circuit. The

user should not plug the phone into a power

outlet, and should not put a charged handset

into the cradle, if the phone is located in an

environment containing concentrations of

flammable or flame-supporting gases, unless

there is adequate ventilation. A spark in

such an environment could create a fire or

explosion. Such environments might include:

medical use of oxygen without adequate

ventilation; industrial gases (cleaning

solvents; gasoline vapors; etc.); a leak of

natural gas; etc.

15. The power adapters are intended to be

correctly oriented in a vertical or floor mount

position. The prongs are not designed to hold

the plug in place if it is plugged into a ceiling,

under-the-table or cabinet outlet.

SAVE THESE INSTRUCTIONS

Battery

CAUTION: Use Only Supplied Battery.

Do not dispose of the battery in a fire. Check

with local waste management codes for

special disposal instructions.

Do not open or mutilate the battery. Released

electrolyte is corrosive and may cause burns

or injury to the eyes or skin. The electrolyte

may be toxic if swallowed.

Exercise care in handling batteries in

order not to create a short circuit with

conductive materials.

Charge the battery provided with or identified

for use with this product only in accordance

with the instructions and limitations specified

in this manual.

•

Precautions for users of implanted cardiac

pacemakers

Cardiac pacemakers (applies only to digital

cordless telephones):

Wireless Technology Research, LLC (WTR),

an independent research entity, led a

multidisciplinary evaluation of the interference

between portable wireless telephones and

implanted cardiac pacemakers. Supported by

the U.S. Food and Drug Administration, WTR

recommends to physicians that:

Pacemaker patients

Should keep wireless telephones at least six

inches from the pacemaker.

Should NOT place wireless telephones directly

over the pacemaker, such as in a breast

pocket, when it is turned ON.

Should use the wireless telephone at the ear

opposite the pacemaker.

WTR’s evaluation did not identify any risk to

bystanders with pacemakers from other persons

using wireless telephones.

About cordless telephones

Privacy: The same features that make a

cordless telephone convenient create some

limitations. Telephone calls are transmitted

between the telephone base and the

cordless handset by radio waves, so there

is a possibility that the cordless telephone

conversations could be intercepted by radio

receiving equipment within range of the

cordless handset. For this reason, you should

not think of cordless telephone conversations

as being as private as those on corded

telephones.

Electrical power: The telephone base of this

cordless telephone must be connected to a

working electrical outlet. The electrical outlet

should not be controlled by a wall switch. Calls

cannot be made from the cordless handset if

the telephone base is unplugged, switched off

or if the electrical power

is interrupted.

Potential TV interference: Some cordless

telephones operate at frequencies that may

cause interference to televisions and VCRs.

To minimize or prevent such interference, do

not place the telephone base of the cordless

telephone near or on top of a TV or VCR. If

interference is experienced, moving the cordless

telephone farther away from the TV or VCR often

reduces or eliminates the interference.

Rechargeable batteries: Exercise care in

handling batteries in order not to create a

short circuit with conducting material such

as rings, bracelets, and keys. The battery or

conductor may overheat and cause harm.

Observe proper polarity between the battery

and the battery charger.

•

Lithium-ion rechargeable batteries: Dispose

of these batteries in a safe manner. Do not

burn or puncture the battery. Like other

batteries of this type, if burned or punctured,

they could release caustic material which

could cause injury.

The RBRC® seal

The RBRC® seal on the lithium-ion battery

indicates that VTech Communications, Inc. is

voluntarily participating in an industry program

to collect and recycle these batteries at the end

of their useful lives, when taken out of service

within the United States and Canada.

The RBRC® program provides a convenient

alternative to placing used lithium-ion batteries

into the trash or municipal waste, which may be

illegal in your area.

VTech’s participation in RBRC

makes it easy

for you to drop off the spent battery at local

retailers participating in the RBRC

program or

at authorized VTech product service centers.

Please call 1 (800) 8 BATTERY

for information

on Li-ion battery recycling and disposal bans/

restrictions in your area. VTech’s involvement

in this program is part of its commitment to

protecting our environment and conserving natural

resources.

RBRC® and

1 (800) 8 BATTERY

are registered trademarks of

Rechargeable Battery Recycling

Corporation.

FCC, ACTA and IC regulations

FCC Part 15

NOTE: This equipment has been tested and

found to comply with the requirements for a

Class B digital device under Part 15 of the

Federal Communications Commission (FCC)

rules. These requirements are intended to

provide reasonable protection against harmful

interference in a residential installation. This

equipment generates, uses and can radiate radio

frequency energy and, if not installed and used

in accordance with the instructions, may cause

harmful interference to radio communications.

However, there is no guarantee that interference

will not occur in a particular installation. If this

equipment does cause harmful interference

to radio or television reception, which can be

determined by turning the equipment off and

on, the user is encouraged to try to correct the

interference by one or more of the following

measures:

Reorient or relocate the receiving antenna.

Increase the separation between the

equipment and receiver.

•

Connect the equipment into an outlet on a

circuit different from that to which the receiver is

connected.

Consult the dealer or an experienced radio/TV

technician for help.

WARNING: Changes or modifications to this

equipment not expressly approved by the party

responsible for compliance could void the user’s

authority to operate the equipment.

This device complies with Part 15 of the FCC

rules. Operation is subject to the following two

conditions: (1) this device may not cause harmful

interference, and (2) this device must accept

any interference received, including interference

that may cause undesired operation. Privacy of

communications may not be ensured when using

this telephone.

To ensure safety of users, the FCC has

established criteria for the amount of radio

frequency energy that can be safely absorbed

by a user or bystander according to the intended

usage of the product. This product has been

tested and found to comply with the FCC criteria.

The handset may be safely held against the ear

of the user. The telephone base shall be installed

and used such that parts of the user’s body other

than the hands are maintained at a distance of

approximately 20 cm (8 inches) or more.

This Class B digital apparatus complies with

Canadian requirement:

CAN ICES-3 (B)/NMB-3(B)

This equipment must not be used with Party

Lines. If you have specially wired alarm dialing

equipment connected to your telephone line,

ensure the connection of this equipment

does not disable your alarm equipment. If you

have questions about what will disable alarm

equipment, consult your telephone service

provider or a qualified installer.

If this equipment is malfunctioning, it must

be unplugged from the modular jack until the

problem has been corrected. Repairs to this

telephone equipment can only be made by the

manufacturer or its authorized agents. For repair

procedures, follow the instructions outlined under

the Limited warranty.

If this equipment is causing harm to the

telephone network, the telephone service

provider may temporarily discontinue your

telephone service. The telephone service

provider is required to notify you before

interrupting service. If advance notice is not

practical, you will be notified as soon as possible.

You will be given the opportunity to correct the

problem and the telephone service provider

is required to inform you of your right to file a

complaint with the FCC. Your telephone service

provider may make changes in its facilities,

equipment, operation, or procedures that could

•

affect the proper functioning of this product. The

telephone service provider is required to notify

you if such changes are planned.

If this product is equipped with a corded or

cordless handset, it is hearing aid compatible.

If this product has memory dialing locations,

you may choose to store emergency telephone

numbers (e.g., police, fire, medical) in these

locations. If you do store or test emergency

numbers, please:

Remain on the line and briefly explain the reason

for the call before hanging up.

Perform such activities in off-peak hours, such as

early morning or late evening.

Industry Canada

This device complies with Industry Canada

license-exempt RSS standard(s).

Operation is subject to the following two

conditions: (1) this device may not cause harmful

interference, and (2) this device must accept any

interference received, including interference that

may cause undesired operation.

Privacy of communications may not be ensured

when using this phone.

The term ‘’IC:‘’ before the certification/

registration number only signifies that the

Industry Canada technical specifications were

met.

This product meets the applicable Innovation,

Science, and Economic Development Canada

technical specifications.

California Energy Commission

battery charging testing

instructions

This headset is set up to comply with the

energy-conserving standards right out of the box.

These instructions are intended for California

Energy Commission (CEC) compliance testing

only. When the CEC battery charging testing

mode is activated, all headset functions, except

headset battery charging, will be disabled.

To activate the CEC battery charging

testing mode:

Before proceeding, make sure the headset

battery has enough charge and the headset

charger is connected to power.

Press VOL+, ON/OFF key, VOL-, ON/OFF

key, VOL+, VOL- and ON/OFF key.

NOTES

When the headset successfully enters the CEC

battery charging testing mode, the ON/OFF light on

the headset flashes slowly and alternately in red

and blue. Press ON/OFF key and you hear “Not

registered.” Then put the headset in the headset

charger for charging.

When the headset fails to enter this mode, repeat

Step 1 to Step 2 above.

To deactivate the CEC battery charging

testing mode:

Before proceeding, make sure the headset

battery has enough charge. Make sure the

telephone base and headset charger are

connected to power.

base. See Add and register a headset for

headset registration instructions.

For C-UL compliance only

Afin de réduire les risques d’incendie, de

blessures corporelles ou d’électrocution, suivez

toujours ces mesures préventives de base

lorsque vous utilisez votre téléphone :

Lisez et comprenez bien toutes les

instructions.

Observez toutes les instructions et mises en

garde inscrites sur l’appareil.

Débranchez ce téléphone de la prise murale

avant de le nettoyer. N’utilisez pas de

nettoyeurs liquides ni en aérosol. N’utilisez

qu’un chiffon doux et légèrement humecté.

N’utilisez pas ce produit près de l’eau, tel

que près d’un bain, d’un lavabo, d’un évier de

cuisine, d’un bac de lavage ou d’une piscine,

ou dans un sous-sol humide ou sous la

douche.

Ne déposez pas ce téléphone sur un chariot,

support ou table chancelants. L’appareil

pourrait tomber et être sérieusement

endommagé.

Le boîtier de l’appareil est doté de fentes et

d’ouvertures d’aération situées à l’arrière ou

en dessous. Afin d’empêcher la surchauffe,

ces ouvertures ne doivent pas être obstruées

en plaçant l’appareil sur un lit, divan, tapis

ou autre surface similaires. Ne placez pas

cet appareil à proximité d’un élément de

chauffage ni d’une plinthe électrique. De plus,

ne l’installez pas dans une unité murale ou un

cabinet fermé qui ne possède pas d’aération

adéquate.

Ne faites fonctionner cet appareil qu’avec le

type d’alimentation indiqué sur les étiquettes

de l’appareil. Si vous ne connaissez pas le

voltage de votre maison, consultez votre

marchand ou votre fournisseur d’électricité.

•

Ne déposez rien sur le cordon d’alimentation.

Installez cet appareil dans un endroit

sécuritaire, là où personne ne pourra

trébucher sur la ligne d’alimentation ni le

cordon téléphonique modulaire.

N’insérez jamais d’objets à travers les

fentes et ouvertures de cet appareil, car ils

pourraient toucher à des points de tension

dangereux ou court-circuiter des pièces,

ce qui constituerait un risque d’incendie ou

d’électrocution. N’échappez pas de liquides

dans l’appareil.

Afin de réduire les risques d’électrocution,

ne démontez pas l’appareil, mais apportez-le

plutôt à un centre de service qualifié s’il doit

être réparé. En enlevant le couvercle, vous

vous exposez à des tensions dangereuses

ou autres dangers similaires. Un remontage

inadéquat peut être à l’origine d’une

électrocution lors d’une utilisation ultérieure

de l’appareil. Débranchez l’appareil avant de

procéder au nettoyage. Utilisez un chiffon

humide et doux.

Ne surchargez pas les prises de courant et

les rallonges.

Débranchez cet appareil de la prise

de courant et communiquez avec le

département de service à la clientèle de

VTech dans les cas suivants:

Lorsque le cordon d’alimentation est

endommagé ou écorché.

Si du liquide a été échappé dans

l’appareil.

Si l’appareil a été exposé à une source

d’humidité telle que la pluie ou l’eau.

Si le produit ne fonctionne pas

normalement en respectant les

instructions de fonctionnement.

Réglez uniquement les commandes

indiquées dans le les instructions de

fonctionnement. Les réglages incorrects

des autres commandes pourraient

provoquer un dommage qui pourrait

exiger un travail exhaustif de la part d’un

technicien autorisé afin de rétablir le

fonctionnement normal de l’appareil.

Si le produit a été échappé et que

le socle et/ou le combiné a été

endommagé.

Si le produit affiche une nette diminution

de sa performance.

13. Évitez d’utiliser un téléphone (autre qu’un

sans fil) pendant un orage. Les éclairs

peuvent être à l’origine d’une électrocution.

14. N’utilisez pas le téléphone pour rapporter

une fuite de gaz à proximité de la fuite. En

certaines circonstances, une flammèche

pourrait être provoquée lorsque l’adaptateur

est branché à une prise de courant, ou

lorsque le combiné est déposé sur le socle.

10.

11.

12.

•

Ceci est un événement commun associé à la

fermeture d’un circuit électrique. L’utilisateur

ne devrait pas brancher le téléphone à

une prise de courant, et ne devrait pas

déposer le combiné chargé sur le socle,

si le téléphone se trouve à proximité d’un

endroit comportant des concentrations de

gaz inflammables, à moins que la ventilation

soit adéquate. Une flammèche dans un

tel endroit pourrait provoquer un incendie

ou une explosion. De tels environnements

peuvent comprendre: des endroits où l’on

utilise de l’oxygène médical sans ventilation

adéquate; des gaz industriels (dissolvants

de nettoyage, des vapeurs d’essence, etc.);

une fuite de gaz naturel, etc.

15. Ces adaptateurs ont été conçus pour être

orientés en position verticale ou montés au

sol. Les broches ne sont pas conçues pour

maintenir l’adaptateur en place si celui-ci est

barnché dans une prise au plafond ou sous

une table/ armoire.

CONSERVEZ CES INSTRUCTIONS

Pile

MISE EN GARDE : N’utilisez que la pile

incluse.

Ne jetez pas la pile au feu. Vérifiez les

instructions spécifiques de mise aux rebus

aupr

s des autorités locales.

N’ouvrez pas et ne mutilez pas la pile.

L’électrolyte qui s’en échapperait est corrosif

et pourrait causer des brûlures ou des

blessures aux yeux ou à la peau. L’électrolyte

est toxique si avalé.

Soyez prudents lorsque vous manipulez les

piles afin d’éviter les courts-circuits provoqués

par des matériaux conducteurs.

Rechargez la pile incluse avec cet appareil,

selon les instructions et limites spécifiées

dans ce guide d’utilisation.

Stimulateurs cardiaques implantés dans

l’organisme

Les simulateurs cardiaques (s’applique

uniquement aux téléphones numériques sans fil):

L’organisme ‘Wireless Technology Research, LLC

(WTR)’, une firme de recherche indépendante,

a mené une évaluation pluridisciplinaire des

interférences entre les téléphones sans fil

portatifs et les stimulateurs cardiaques implantés

dans l’organisme. Appuyée par l’Administration

des aliments et drogues (FDA) des États-Unis, la

firme WTR recommande aux médecins:

Avis aux détenteurs de stimulateurs

cardiaques

Ils doivent tenir le téléphone sans fil à une

distance d’au moins six pouces du stimulateur

cardiaque.

•

Ils ne doivent PAS placer le téléphone sans

fil directement sur le stimulateur cardiaque,

tel que dans une poche de chemise, lorsque

celui-ci est en marche.

Ils doivent utiliser le téléphone sans fil en

l’appuyant sur l’oreille qui se trouve dans la

direction opposée au stimulateur cardiaque.

L’étude effectuée par l’organisme WRS n’a

pas identifié de risque pour les détenteurs de

simulateurs cardiaques causés par les gens qui

utilisent un téléphone sans fil à proximité de ceux-ci.

À propos des téléphones sans fil

Alimentation électrique: Les mêmes

caractéristiques qui constituent des avantages

pour les téléphones sans fil affichent également

des restrictions. Les appels téléphoniques

sont transmis entre le combiné sans fil et

le socle par le biais d’ondes radio ; il y a

donc la possibilité que vos conversations

téléphoniques sans fil soient interceptées par

des équipements de réception radio se trouvant

dans la portée du combiné sans fil. Pour

cette raison, vous ne devez pas percevoir les

communications téléphoniques sans fil comme

étant aussi confidentielles.

Alimentation électrique: Le socle de ce

téléphone sans fil doit être branché à une

prise électrique fonctionnelle. La prise

électrique ne doit pas être contrôlée par un

interrupteur mural. Les appels ne pourront pas

être effectués du combiné sans fil si le socle

est débranché ou mis hors tension ou si le

courant est coupé.

Possibilité d’interférences aux téléviseurs:

Certains téléphones sans fil fonctionnent

sur des fréquences pouvant causer des

interférences aux téléviseurs et aux

magnétoscopes. Pour réduire ou prévenir de

telles interférences, ne placez pas le socle du

téléphone sans fil près ou sur un téléviseur ou

magnétoscope. S’il y a présence de parasites,

il est conseillé d’éloigner le téléphone sans

fil du téléviseur ou du magnétoscope afin de

réduire possiblement les interférences.

Piles rechargeables: Manipulez les piles

avec soin afin de ne pas les court-circuiter

avec des bagues, bracelets ou clés. Les piles

ou le conducteur peut surchauffer et causer

des blessures. Respectez la polarité adéquate

entre la pile et le chargeur.

Les bloc-piles rechargeables à au

lithium-ion: Jetez ces blocs-piles de manière

écologique et sécuritaire. Ne les incinérez

pas et ne les percez pas. Tel que les autres

piles de ce type, elles pourraient dégager une

matière toxique qui peut causer des blessures

corporelles si elles sont brûlées ou percées.

•

Limited warranty

What does this limited warranty cover?

The manufacturer of this VTech Product warrants

to the holder of a valid proof of purchase

(“Consumer” or “you”) that the Product and

all accessories provided in the sales package

(“Product”) are free from defects in material

and workmanship, pursuant to the following

terms and conditions, when installed and used

normally and in accordance with the Product

operating instructions. This limited warranty

extends only to the Consumer for Products

purchased and used in the United States of

America and Canada.

What will VTech do if the Product is not free

from defects in materials and workmanship

during the limited warranty period (“Materially

Defective Product”)?

During the limited warranty period, VTech’s

authorized service representative will repair

or replace at VTech’s option, without charge,

a Materially Defective Product. If we repair

the Product, we may use new or refurbished

replacement parts. If we choose to replace

the Product, we may replace it with a new or

refurbished Product of the same or similar

design. We will retain defective parts, modules, or

equipment. Repair or replacement of the Product,

at VTech’s option, is your exclusive remedy.

VTech will return the repaired or replacement

Products to you in working condition. You

should expect the repair or replacement to take

approximately 30 days.

How long is the limited warranty period?

The limited warranty period for the Product extends

for ONE (1) YEAR from the date of purchase. If

VTech repairs or replaces a Materially Defective

Product under the terms of this limited warranty,

this limited warranty also applies to the repaired

or replacement Product for a period of either

(a) 90 days from the date the repaired or

replacement Product is shipped to you or (b) the

time remaining on the original one-year warranty;

whichever is longer.

What is not covered by this limited warranty?

This limited warranty does not cover:

Product that has been subjected to misuse,

accident, shipping or other physical damage,

improper installation, abnormal operation or

handling, neglect, inundation, ﬁre, water or

other liquid intrusion; or

Product that has been damaged due

to repair, alteration or modiﬁcation by

anyone other than an authorized service

representative of VTech; or

Product to the extent that the problem

experienced is caused by signal conditions,

network reliability, or cable or antenna

systems; or

Product to the extent that the problem is

caused by use with non-VTech accessories;

Product whose warranty/quality stickers,

product serial number plates or electronic

serial numbers have been removed, altered or

rendered illegible; or

Product purchased, used, serviced, or

shipped for repair from outside the United

States of America or Canada, or used

for commercial or institutional purposes

(including but not limited to Products used for

rental purposes); or

Product returned without a valid proof of

purchase; or

Charges for installation or set up, adjustment

of customer controls, and installation or repair

of systems outside the unit.

How do you get warranty service?

To obtain warranty service in the USA, please

visit our website at www.vtechphones.com or

call 1 (800) 595-9511. In Canada, go to

www.vtechcanada.com or call

1 (800) 267-7377.

NOTE: Before calling for service, please review

the user’s manual - a check of the Product’s

controls and features may save you a service call.

Except as provided by applicable law, you

assume the risk of loss or damage during

transit and transportation and are responsible

for delivery or handling charges incurred in the

transport of the Product(s) to the service location.

VTech will return repaired or replaced Product

under this limited warranty. Transportation,

delivery or handling charges are prepaid.

VTech assumes no risk for damage or loss of

the Product in transit. If the Product failure is

not covered by this limited warranty, or proof of

purchase does not meet the terms of this limited

warranty, VTech will notify you and will request

that you authorize the cost of repair prior to any

further repair activity. You must pay for the cost

of repair and return shipping costs for the repair

of Products that are not covered by this limited

warranty.

What must you return with the Product to get

warranty service?

Return the entire original package and

contents including the Product to the VTech

service location along with a description of

the malfunction or difﬁculty; and

Include a “valid proof of purchase” (sales

receipt) identifying the Product purchased

(Product model) and the date of purchase or

receipt; and

Provide your name, complete and correct

mailing address, and telephone number.

Other limitations

This warranty is the complete and exclusive

agreement between you and VTech. It supersedes

all other written or oral communications related to

this Product. VTech provides no other warranties

for this Product. The warranty exclusively describes

all of VTech’s responsibilities regarding the

Product. There are no other express warranties.

No one is authorized to make modiﬁcations to this

limited warranty and you should not rely on any

such modiﬁcation.

State/Provincial Law Rights: This warranty gives

you speciﬁc legal rights, and you may also have

other rights, which vary from state to state or

province to province.

Limitations: Implied warranties, including

those of ﬁtness for a particular purpose and

merchantability (an unwritten warranty that the

Product is ﬁt for ordinary use) are limited to one

year from the date of purchase. Some states/

provinces do not allow limitations on how long

an implied warranty lasts, so the above limitation

may not apply to you. In no event shall VTech

be liable for any indirect, special, incidental,

consequential, or similar damages (including, but

not limited to lost proﬁts or revenue, inability to

use the Product or other associated equipment,

the cost of substitute equipment, and claims

by third parties) resulting from the use of this

Product. Some states/provinces do not allow

the exclusion or limitation of incidental or

consequential damages, so the above limitation

or exclusion may not apply to you.

Please retain your original sales receipt

as proof of purchase.

3. Technical specifications

RF frequency band 1921.536-1928.448 MHz

Channels 5

Nominal effective

range

Maximum power allowed by

FCC and IC. Actual operating

range may vary according to

environment conditions at the

time of use.

Power requirements Headset: 3.2 - 4.2V DC

Charger: 6V DC @ 400mA

Specifications are subject to change without

notice.

Document order number: 91-010074-020-100

VTech IS6200 Manuel utilisateur

Marque: VTech

Modèle: IS6200

Catégorie: Téléphones

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: VTech IS6200 User manual

VTech IS6200 Manuel utilisateur

VTech IS6200 Manuel utilisateur

dans d''autres langues

Documents connexes