VTech VH6222 Manuel utilisateur

Go to businessphones.vtech.com

to register your product for

enhanced warranty support and

the latest VTech product news.

VH6222

Over-the-ear Ofﬁce

Wireless Headset

with Dongle

User’s manual

BC

Congratulations

on your purchase of this VTech product. Before using this product,

please read the Important safety information.

This Abridged user’s manual provides you with the basic installation

and use instructions. A limited set of features are described in

abbreviated form.

Visit businessphones.vtech.com/support/downloads to download a

full set of installation and operation instructions.

• The software application

“Software application - Installation and Operation Guide”

For customer service or product information, visit our website at

businessphones.vtech.com or call 1 (800) 595-9511. In Canada, please

dial 1 (800) 267-7377.

For VH6222 headset:

HVIN: 35-800001HD

FCC ID: EW780-1360-00

IC: 1135B-80136000

For Dongle VU-060:

FCC ID: EW780-1391-00

IC: 1135B-80139100

Skype® and Skype for Business® are registered trademarks of Microsoft Corporation.

* The VTech Control supports Skype version 7.1-7.40. Later versions of Skype are not

supported by VTech Control for remote headset call control.

The VH6222 includes a cordless headset, charger, and a Dongle. The

Dongle functions as a headset base so that this product allows you to

have handsfree phone conversations.

The Dongle allows you to connect your headset using either one of

the following methods:

• PHONE mode - Connect to an IP phone

Use the Dongle to connect the headset and your VTech/SNOM IP

phone. The headset acts as a supplementary device that can make

and receive calls with the IP phone.

• PC mode - Connect to a computer

Use the Dongle to connect the headset and your PC. You can

make and receive VoIP calls through Skype®* or Skype for

Business®, using

the

VTech Control software application.

Introduction

What’s in the box

Your product package contains the following items. Save your sales

receipt and original packaging in the event warranty service is

necessary.

Headset charger Headset charger

power adapter

User's manual Wireless headset

11 earbuds

Dongle

BC

XL LMS

LS

M

XL LMS

Table of contents

Getting started

Headset overview .........................1

Headset lights ................................ 2

Headset alert tones ...................3

Headset alert prompts ..............3

Headset charger overview ......... 4

Dongle overview ..........................5

Dongle LED lights ......................5

Power up the headset charger .. 6

Charge the headset battery ....... 6

Connection methods ....................7

PHONE mode ............................7

PC mode .....................................7

PHONE mode -

Connect to an IP phone........... 8

Plug the Dongle to

a VTech/SNOM IP phone ........ 8

Plug the Dongle to

a computer ................................ 9

PC mode -

Connect to a computer ..........11

Wear the headset ........................ 12

Change the earbud and wear

the headset ...............................12

Operate

Headset power on/off ...............13

PHONE mode - Operate with

an IP Phone .............................. 14

Before use ................................ 14

Make and receive calls ........... 14

PC mode - Operate with a

computer ..................................15

Before use .................................15

Make and receive calls ............15

Caller ID announce ..................15

Sound settings ............................ 16

Headset ringer ........................ 16

Anti-Startle (G616) .................. 16

Change audio bandwidth ......17

Temporary ringer silencing ... 18

Volume control ....................... 18

Mute .......................................... 18

Appendix

Registering Headset to

Dongle ..................................... 19

Register your Headset to

the Dongle .............................. 19

Frequently asked questions .....20

Maintenance ............................... 24

Important safety information ....25

Safety information ...................25

Especially about cordless

headsets ................................... 26

Precautions for users

of implanted cardiac

pacemakers ..............................27

For C-UL compliance ................. 28

Mesures de sécurité

importantes ............................. 28

FCC Part 68 and ACTA ................32

FCC Part 15 .................................. 34

California Energy Commission

battery charging testing

instructions................................35

Limited warranty ........................ 36

Technical speciﬁcations ............. 39

Disclaimer and Limitation of

Liability .....................................40

1

Getting started

Headset overview

1 – Ear hook

2 – ON/OFF button and LED light

• Press to make, answer or end a call.

• See Headset lights for lights behavior.

3 – Magnetic charging contacts

4 – + (Volume up) / - (Volume down)

• Press to adjust the headset ringer volume while in idle mode, or the listening

volume while on a call.

5 – MUTE

• Mute the microphone during a call.

6 – Earpiece

7 – Microphone

5

6

7

4

2

31

2

Getting started

Headset lights

Color LED light status Meaning

Red Steady light on The battery is low and the headset is in

the charger.

Flash every 10 seconds The battery is low and the headset is

not in the charger.

Flash 3 times Powering off.

Blue Steady light on The battery is fully charged.

Flash every 10 seconds The headset is not in the charger.

Flash 2 times every

3 seconds The headset is in use.

Flash 3 times Powering on.

Flash 4 times every

4 seconds There is an incoming call.

Purple Steady light on The battery is well charged.

Red and

blue Alternate slowly The headset is not registered.

Alternate quickly The headset is trying to register to a

headset base.

Off Light off The battery is depleted.

The headset is powered off.

ON/OFF button and LED light

Press to make, answer or end a call.

3

Getting started

Headset alert

Headset alert tones

Alert tone behavior Meaning

One short beep every

30 seconds

• The microphone is muted.

Two beeps • Error alert tone.

• The speaking volume has reached its highest or

lowest setting.

• Any key is pressed while the headset is out of

range.

Two low beeps • Call waiting alert tone.

Two rapid beeps every

20 seconds

• Low battery warning.

Three rapid beeps every

20 seconds

• The headset is out of range.

Three rapid beeps • The headset is powering on or off.

Headset alert prompts

Alert prompt Meaning

“Mute on” • The microphone is muted.

“Mute off” • The microphone is re-activated.

“Not registered” • ON/OFF button is pressed while the headset

is not registered.

“Out of range” • The headset is on a call and out of range.

• Any key is pressed while the headset is out of

range.

“Low battery” • ON/OFF button is pressed while the headset

battery is low.

4

Getting started

Headset charger overview

1 – Magnetic charging mount

• Place the headset here for charging.

2 – LED light

• Steadily red while the headset charging in the charger.

2

1

5

Getting started

Dongle overview

Color LED light status

Green • Steady green when the Dongle is not in use.

• Steady green for three seconds when the Dongle is

deregistered from the headset.

• Flashes very quickly when there is an incoming call.

• Flashes quickly every three seconds when the headset is in

use.

Red • Steady red when the Dongle is not registered.

• Flashes very quickly when the Dongle is registering to a

headset.

• Flashes quickly when the Dongle is entering deregistration

mode.

• Flashes slowly when the headset is muted.

Dongle LED lights

1

1 – LED light button

• Press and hold for about 4 seconds to enter the registration mode.

• For LED light patterns, see Dongle LED lights below.

6

Getting started

Charge the headset battery

Hang the headset onto the magnetic charging mount.

The magnet holds the headset in place.

• The LED light on the charger will turn steady red while charging.

Notes

• For optimal performance, charge the headset battery for at least 30 minutes before

use. The battery is fully charged after 2 hours of continuous charging. When the

headset is not in use, recharge by hanging it onto the headset charger.

• The headset battery is built-in. If you need to replace the headset, visit our website

at businessphones.vtech.com or call 1 (800) 595–9511 to get a replacement. In

Canada, dial 1 (800) 267-7377.

Power up the headset charger

1. Plug the small end of the headset charger

power adapter at the back of the headset

charger.

2. Plug the large end into an electrical outlet

not controlled by a wall switch.

7

Getting started

Connection methods

Choose one of the following methods to connect your headset for

operation in either PHONE mode or PC mode.

PHONE mode

Connect to an IP phone

• You can connect the headset to an IP phone by plugging the

Dongle to the USB port on your VTech/SNOM IP phone. The

headset acts as a supplementary device that can make and receive

calls with the IP phone.

PC mode

Connect to a computer

• You can connect the headset to your PC by plugging the Dongle to

the USB port on your computer the to your PC. You can make and

receive VoIP calls through Skype or Skype for Business, using

the

software application

.

8

Getting started

PHONE mode - Connect to an IP phone

Plug the Dongle to a VTech/SNOM IP phone

Connect the headset to an IP phone using the Dongle.

You can use the headset to make or answer calls with the IP phone

connected.

1. Plug the Dongle to the USB port on your VTech/SNOM IP phone.

The Dongle LED light will turn steady green.

2. At the telephone base of your VTech/SNOM IP Phone, press to

turn on the headset mode.

Depending on the IP phone model the status icon will appear

on the LCD of your IP phone, or the LED light on the key will

turn on.

Test the headset after connection:

Press

the

ON/OFF button on the headset to make, answer, or end

a call, using the telephone line to which the IP phone is connected.

9

Getting started

PC mode - Connect to a computer

Plug the Dongle to a computer

Connect the headset to a computer using the Dongle.

You can then use the headset for VoIP (Voice over IP) calls through

your computer.

1. Plug the Dongle to the USB port on your computer. The Dongle

LED light will turn steady green.

2. Install the VTech Control.

• Visit businessphones.vtech.com/support/downloads

to download and install the software. You can also download

the Installation and Operation Guide there for installation

and operation instructions of the software.

10

Getting started

3. After you have installed the VTech Control, check to make sure

the audio setting is properly configured in your Windows system.

If you have installed Skype and/or Skype for Business and want

to use them with your headset, make sure the audio settings are

configured correctly in the programs as well.

a) Audio settings in Microsoft® Windows®

(Windows 7 / Windows 8 / Windows 10) system:

i. Click Start menu and choose Control Panel.

ii. Click Hardware and Sound and then click Manage

audio devices under the Sound menu.

iii. Click the Playback tab and make sure VTech Headset is set as

the default speaker.

iv. Click the Recording tab and make sure VTech Headset is set

as the default microphone.

b) Audio settings in Skype (Skype 7.1-7.40):

i. Launch the Skype program.

ii. Click on Tools, then Options.

iii. Click on Audio settings.

iv. Make sure VTech Headset is selected under the speakers and

microphone settings.

Notes

• The VTech Control does not support the App versions of Skype, including both

mobile APP and desktop APP.

• The VTech Control supports Skype version 7.1-7.40. Later versions of Skype are not

supported by VTech Control for remote headset call control.

• After the installation of VTech Control, Skype will prompt a message “VTechControl.

exe is requesting access to Skype”. Choose Allow Access to connect your Skype to

VTech Control.

PC mode - Connect to a computer

Windows® is a registered trademark of Microsoft Corporation.

11

Getting started

c) Audio settings in Skype for Business 2016:

i. Launch the Skype for Business program.

ii. Click on Options, then Audio Device.

iii. Make sure VTech Headset is selected under the Audio device

setting.

PC mode - Connect to a computer

IMPORTANT INFORMATION

• Periodically check for software updates. For more details, download the

VTech Control - Installation and Operation Guide under the product

page of VH6222 on businessphones.vtech.com/support/downloads for

installation and operation instructions of the software.

12

Getting started

Wear the headset

Change the earbud and wear the headset

There are 11 earbuds included, with different sizes and types.

1. The medium-sized gray earbud is pre-attached to the headset. You

can try the other earbuds and choose one that best ﬁts your ear.

Remove them from your ear after trying.

2. Remove the pre-attached medium-sized gray earbud from the

headset and then attach your desired earbud.

• Make sure the

protruding bump is

pointing towards the

microphone when

placed on your ear.

The protruding bump

on the earbud holds

the headset securely

in your ear.

3. Adjust the angle of the headset to ﬁt your ear, and then hook the

headset on your ear.

• The microphone should be pointing towards your mouth, as

close to your cheek as possible without touching.

XL LMS

LS

M

XL LMS

12

Microphone

13

Headset power on/off

To power on the headset:

• Press and hold ON/OFF button for two seconds.

The LED light flashes blue three times, and you hear three

beeps when it is being powered on.

To power off the headset:

• Press and hold ON/OFF button for four seconds.

The LED light flashes red three times, and you hear three beeps

when it is being powered off.

Operate

14

Operate

PHONE mode - Operate with an IP Phone

Before use

Make sure you have plugged your Dongle to the USB port on your

VTech/SNOM IP Phone.

Make and receive calls

To make a call:

1. Press the ON/OFF button on the headset. You hear a dial tone in

the headset earpiece.

2. Dial the telephone number using the dialing keys on the IP phone.

To answer a call:

• Press the ON/OFF button on the headset to answer an

incoming call.

You hear the caller through the headset earpiece.

To end a call:

• Press the ON/OFF button on the headset to end a call. The EHS

connection automatically releases the line on your IP phone.

15

Operate

PC mode - Operate with a computer

Before use

Make sure you have plugged your Dongle to the USB port on your

computer, and have already installed the VTech Control on your

computer, before you use your headset.

Download the VTech Control and the

Installation and Operation

Guide

at

businessphones.vtech.com/support/downloads

, under

the product page of VH6222.

Unzip and install the VTech Control after download.

Make and receive calls

You can make and receive VoIP calls with your VTech Control through

Skype and Skype for Business.

Caller ID announce

The Caller ID announce feature with your VTech Control lets you know

who is calling without having to look at the display.

La page est en cours de chargement...

VTech VH6222 Manuel utilisateur

VTech VH6222 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents