1
OWNER’S MANUAL
Model number
700316-3 (
Polypropylene brush)
BERCO
Rotary Broom
for
LAWN, YARD, & GARDEN TRACTORS
BELT OR SHAFT DRIVE P.T.O.
104681 I-05
* ASSEMBLY * REPAIR PARTS
* OPERATION * MAINTENANCE
CAUTION:
READ & FOLLOW ALL SAFETY RULES & INSTRUCTIONS
BEFORE OPERATING YOUR EQUIPMENT
*104681*
2
LIMITED WARRANTY
Bercomac Limitée
92, Fortin Nord, Adstock, Québec, Canada, G0N 1S0
Conditions and Products Covered:
BERCOMAC guarantees any part of the product or accessory
manufactured by BERCOMAC and found in the reasonable
judgment of BERCOMAC to be defective in material and or
workmanship will be repaired or replaced by an authorized
dealer without charge up to our maximum labor rates and pre-
established times. For replacement parts only standard
ground freight services are covered. This warranty extends to
the original retail purchaser only and is not transferable to any
subsequent purchasers.
Warranty Period
(from date of the original retail purchase):
x Residential use: 1 year
x Commercial or rental use: 90 days
Exceptions Noted Below: the following items are
guaranteed by the original manufacturer and have their own
warranty, conditions and limited time:
x Tire Chains: 90 days
x Engines (installed in factory on BERCO equipment): 2
years
x Engines (sold separately): Validate with the dealer.
Please refer to the engine manufacturer’s warranty
statement included with the unit. BERCOMAC is not
authorized to handle warranty adjustments on engines.
Items and Conditions NOT Covered:
This warranty does not cover the following:
x Pick-up or delivery charges or in-home services fees.
x Any damage or deterioration of the unit, parts and or finish
of these due to normal use, wear and tear, or exposure.
x Cost of regular use or maintenance service or parts, such
as gas, oil, lubricants, tune-up parts, and adjustments.
x Any part or accessory which has been altered, modified,
misused, neglected, accidentally damaged or not properly
installed, maintained, stored or repaired not in accordance
with the instructions in the owner’s manual.
x Repair due to normal wear and or any wear items such as
shear pins, bolts, belts, etc.
x Expedited freight fee services for replacement parts.
x Shear bolts and shear pins are to be considered as a
preventive measure not as an assured protection, any
damages resulting from the lack of shear bolts breakage
are not covered.
NOTE: All warranty work must be performed by an authorized
dealer using original (manufacturer) replacement parts.
Owner’s Responsibilities:
BERCOMAC’s defective equipment or part must be returned
to an authorized dealer within the warranty period for repairs.
In the event that defective merchandise must be returned to
manufacturer for repairs, freight fees are prepaid and a
written authorization from BERCOMAC must be obtained by
dealer prior to the shipment. This warranty extends only to
equipment operated under normal conditions. To validate a
warranty claim, it is the user’s responsibility to maintain and
service the unit as specified in the owner’s manual or to
have the unit serviced at their dealer at their expense.
General Conditions:
The sole liability of BERCOMAC with respect to this warranty
shall be strictly and exclusively repair and replacement as
mentioned herein. BERCOMAC shall not have any liability
for any other costs, loss or damage, including but not limited
to, any incidental or consequential loss or damage.
In particular, without being limited to, BERCOMAC shall have
no liability or responsibility for:
x Travel time, overtime, after hours time or other
extraordinary repair charges or relating to repairs and or
replacements outside of normal business hours.
x Rental of like or similar replacement equipment during the
period of any, repair or replacement work.
x Any communicating or travel charges.
x Loss or damage to person or property other than that
covered by the terms of this warranty.
x Any claims for lost revenue, lost profit or any similar costs
as a result of damage or repair.
x Attorney’s fees.
BERCOMAC’s responsibility in respect to claims is limited to
making the required repairs or replacement without charge
up to our maximum labor rates and pre-established times
and no claim of breach of warranty shall be cause for
cancellation or rescission of the contract of sale of any
product or accessory.
This warranty gives you specific legal rights. You may also
have other rights, which vary from state to state.
Note: Bercomac reserves the right to change or improve the design of any part or accessory without assuming any obligation to modify
any product previously manufactured.
Instructions for Obtaining Warranty Services:
Contact dealer where equipment was purchased or any other BERCOMAC Service Dealer to arrange service at their dealership. To
locate a dealer convenient to you, access our website at www.bercomac.com.
Bring the product and your proof of purchase (sales receipt) to the BERCOMAC dealer.
1
TABLE OF CONTENTS
INTRODUCTION ................................................................................................................................................... 2
SAFETY PRECAUTIONS ..................................................................................................................................... 3
SAFETY DECALS ................................................................................................................................................. 5
ASSEMBLY
Tools Required ......................................................................................................................................... 6
Step 1: Rotary Broom Preparation ......................................................................................................... 6
Step 2: Rotary Broom Installation .......................................................................................................... 7
Handle Installation ....................................................................................................................... 7
Verify Tire Pressure .................................................................................................................... 7
OPERATION
Rotary Broom Angle Adjustment ............................................................................................................. 8
Pressure on the Brush Adjustment ......................................................................................................... 8
General Sweeping ................................................................................................................................... 8
Snow Sweeping ....................................................................................................................................... 8
Lawn Dethatching and Leaf Raking ........................................................................................................ 8
MAINTENANCE & DISMOUNTING
Maintenance ............................................................................................................................................. 9
Brush Replacement ................................................................................................................................. 9
Dismounting ............................................................................................................................................. 9
End of Season Storage ........................................................................................................................... 9
TROUBLESHOOTING .......................................................................................................................................... 10
TORQUE SPECIFICATION TABLE ..................................................................................................................... 11
PARTS BREAKDOWN AND LISTS
Rotary Broom ........................................................................................................................................... 12
ATTACHMENTS .................................................................................................................................................... 16
PAGE
2
INTRODUCTION
TO THE PURCHASER
This new accessory was carefully designed to give years of dependable service. This manual has been provided to
assist in the safe operation and servicing of your accessory.
NOTE: All photographs and illustrations in the manual may not necessarily depict the actual models or accessory, but
are intended for reference only and are based on the latest product information available at the time of publication.
Familiarize yourself fully with the safety recommendations and operating procedures before putting the machine to use.
Carefully read, understand and follow these recommendations and insist that they be followed by those who will use
this attachment.
THIS SAFETY ALERT SYMBOL IDENTIFIES AN IMPORTANT SAFETY MESSAGE IN THIS MANUAL
THAT HELPS YOU AND OTHERS AVOID PERSONAL INJURY OR EVEN DEATH. DANGER,
WARNING, AND CAUTION ARE SIGNAL WORDS USED TO IDENTIFY THE LEVEL OF HAZARD.
HOWEVER, REGARDLESS OF THE HAZARD, BE EXTREMELY CAREFUL.
DANGER: Signals an extreme hazard that will cause serious injury or death if recommended precautions are
not followed.
WARNING: Signals a hazard that may cause serious injury or death if the recommended precautions are not
followed.
CAUTION: Signals a hazard that may cause minor or moderate injury if the recommended precautions are not
followed.
Record your attachment serial number and purchase date in the section reserved below (there is no serial number on
the subframe). Your dealer requires this information to give you prompt, efficient service when ordering replacement
parts. Use only genuine parts when replacements are required.
If warranty repairs are required please present this registration booklet and original sales invoice to your selling dealer
for warranty service.
This manual should be kept for future reference.
Please check if you have received all the parts for your kit with the list of the
bag and the list of the box.
SERIAL NUMBER : ___________________________
PURCHASE DATE : ___________________________
3
SAFETY PRECAUTIONS
Careful operation is your best insurance against an accident. Read this section carefully before operating the vehicle
and accessory. This accessory is capable of amputating hands and feet and throwing objects. Failure to observe the
following safety instructions could result in serious injury. All operators, no matter how experienced they may be,
should read this and other manuals related to the vehicle and accessory before operating. It is the owner's legal
obligation to instruct all operators in safe operation of the accessory.
GLOSSARY:
In this manual, right and left sides are determined by
sitting on the seat of the vehicle facing forward.
In this manual, "accessories" means attachments
(snowblower, rotary broom, blade etc.) that you install
on the vehicle (lawn tractors, A.T.V. s etc).
TRAINING:
This symbol, "Safety Alert Symbol", is used
throughout this manual and on the accessory’s
safety labels to warn of the possibility of serious
injury. Please take special care in reading and
understanding the safety precautions before
operating the vehicle and accessory.
1. Read this owner's manual carefully. Be thoroughly
familiar with the controls and proper use of the
vehicle and accessory. Know how to stop the unit
and disengage the controls quickly.
2. Never allow children to operate the vehicle nor the
accessory. Never allow adults to operate the vehicle
nor the accessory without proper instructions.
3. No one should operate the vehicle nor the
accessory while intoxicated or while taking
medication that impairs the senses or reactions.
4. Keep the area of operation clear of all people,
particularly small children and pets.
PREPARATION:
1. Thoroughly inspect the area where the accessory
is to be used and remove door mats, all foreign
objects and the like.
2. For motorized accessories, disengage all clutches
and shift into neutral before starting engine.
3. Do not operate the accessory without wearing
adequate winter outer garments. Avoid loose fitting
clothing that can get caught in moving parts. Wear
footwear that will improve footing on slippery
surfaces.
4. Handle fuel with care, it is highly flammable.
a) Use approved fuel container.
b) Never add fuel to a running engine or hot engine.
c) Fill fuel tank outdoors with extreme care. Never fill
fuel tank indoors.
d) Never fill containers inside a vehicle, or on a
truck or a trailer bed with a plastic liner. Always
place containers on the ground, away from your
vehicle, before filling.
e) When practical, remove gas-powered
equipment from the truck or trailer and refuel it
on the ground. If this is not possible, then refuel
such equipment on a trailer with a portable
container, rather than from a gasoline
dispenser nozzle.
f) Keep the nozzle in contact with the rim of the
fuel tank or container opening at all times, until
refueling is complete. Do not use a nozzle lock-
open device.
g) Replace fuel cap securely and wipe up spilled
fuel.
h) If fuel is spilled on clothing, change clothing
immediately.
5. Never attempt to make any adjustments while the
engine (motor) is running (except when specifically
recommended by manufacturer).
6. Let the vehicle and accessory adjust to outdoor
temperatures before starting to clear snow.
7. Always wear safety glasses or eye shields during
operation or while performing an adjustment or
repairs to protect the eyes from foreign objects that
may be thrown from the accessory.
8. Never modify the accessory or any part without
the written consent from the manufacturer.
4
SAFETY PRECAUTIONS
OPERATION:
1. Do not put hands or feet near, under or inside
rotating parts.
2. Exercise extreme caution when operating on or
crossing gravel drives, walks or roads. Stay alert for
hidden hazards or traffic. Do not carry passengers.
3. After striking a foreign object, stop the engine
(motor), disconnect the wire from the spark plug(s)
and keep wire away to prevent accidental starting.
Thoroughly inspect the accessory for any damage
and repair damage before restarting and using the
accessory.
4. If the unit should start to vibrate abnormally, stop
the engine (motor) and check immediately for the
cause. Vibration is generally a warning of trouble.
5. Take all possible precautions when leaving the
vehicle unattended. Disengage the power take-off,
lower the attachment, place the transmission into
neutral, set the parking brake, stop the engine and
remove the contact key.
6. Do not run the engine indoors, except when
starting the engine and for transporting in or out of
the building. Do not operate or let motor run in a
storage area without ventilation because gas
contains carbon monoxide which is odorless,
colorless and can cause death.
7. Never clean across the face of slopes, go from top
to bottom. Exercise extreme caution when using
equipment on slopes. Do not attempt to clear a
steep slope.
8. Never use an accessory without proper guards,
plates, or other safety protective devices in place
9. Never tolerate bystanders in the working zone.
Never use an accessory in the direction of
bystanders, it might throw gravel or debris that can
hurt people or damage property.
10.Never operate the rotary broom at high transport
speeds on slippery surfaces. Use care when
backing up.
11.Do not carry passengers.
12.Disengage power to the accessory when it is
transported or not in use.
WHENEVER YOU SEE THIS SYMBOL
IT MEANS:
WARNING!
BECOME ALERT !
YOUR SAFETY IS INVOLVED!
MAINTENANCE AND STORAGE
1.When cleaning, repairing or inspecting the vehicle
and accessory, make certain that all moving parts
have stopped. Disconnect wire from the spark plug
(s) and keep wire away to prevent accidental
starting.
2. Check all the bolts at frequent intervals to make
sure that they are properly tightened .
3. Never store a motorized accessory with fuel in the
fuel tank inside a building where ignition sources
are present such as hot water and space heaters,
clothes dryers, and the like. Allow the engine to cool
before storing in any enclosure.
4. Always refer to the owner’s manual when you store
the accessory and vehicle for a prolonged or an
unspecified length of time.
5. Maintain or replace safety and instruction labels, as
necessary.
6. For winter accessories, (if applicable), let the engine
run for a few minutes after clean snow in order to
prevent the rotary parts from freezing.
7. Inspect the vehicle’s and accessory’s air filter every
day. Clean it or replace it as necessary. Change the
oil more often when working in dusty conditions.
See the vehicle’s and accessory's owner’s manual.
13.Never operate the accessory without good visibility
or light.
14.Keep the accessory away from heat sources or
flames.
15.Always wear a dust mask when working in a dusty
environment.
5
SAFETY DECALS
REPLACE IF DECALS ARE DAMAGED
SEE PARTS BREAKDOWN FOR DECAL LOCATION
Decal #102386 Decal #102384
6
ASSEMBLY
STEP 1
ROTARY BROOM PREPARATION
IMPORTANT: TORQUE ALL BOLTS ACCORDING
TO TORQUE SPECIFICATION TABLE (SEE TABLE
OF CONTENTS) WHEN STATED: TIGHTEN FIRMLY.
REFER TO PARTS BREAKDOWN SECTION FOR
PARTS IDENTIFICATION
See adaptor mounting Instruction Booklet for
adaptor preparation and installation of the
adaptor.
Install the joint block (item 1) on the latch rod (item 2)
and secure with a retaining ring (item 3).
Install the control rod (item 4) in the joint block (item
1) and secure with a 2.5 mm hair pin (item 5).
Install the parking stands (item 1) in the stand holders
(item 2). Secure with a 5/32 x 1" cotter pin (item 3) in
the upper hole (item 4) and a hair pin 2.5 mm (item 5)
in the lower hole (item 6) of each parking stand.
This will allow the broom to rest on the stand.
Prepare broom
Install the parking stands
TOOLS REQUIRED:
1 pair of long nose pliers
7
ASSEMBLY
Attach the rotary broom to the subframe as shown.
Make sure the rotary broom is pushed in until locked
into place by the springs (item 1).
Follow the instructions for the belt
installation in the Adaptor Instruction
Booklet and the Subframe Owner’s
Manual.
STEP 2
ROTARY BROOM INSTALLATION
WARNING
TO PREVENT INJURIES:
Stop the motor.
Apply parking brake.
Remove the ignition key.
Disconnect the wire from the spark plug(s) and
keep away from spark plug(s) to prevent accidental
starting.
Install the rotary broom
DANGER
NEVER OPERATE THE ROTARY BROOM
WITHOUT:
Brush hood
Belt guard
Gear box guard
Extension guard and any other safety protection
devices in place.
HANDLE INSTALLATION
Install the 1/2 x 3" handgrip (item 1) on the handle
(item 2).
Insert the handle through the plastic grommet on the
handle support (item 3) and on the control rod (item
4).
Secure with a 2.5 mm hair pin (item 5).
NOTE: If the subframe includes a handle extension
(item 6), install it between the control rod (item 4) and
the handle (item 2).
VERIFY TIRE PRESSURE:
Check and adjust tractor tire pressure as follows:
Front tires: 14-15 psi
Back tires: 7-8 psi
Tire pressure must be even on both sides of the
tractor.
Install the handle
8
OPERATION
ROTARY BROOM ANGLE ADJUSTMENT
By turning the handle counter clockwise you unlock the
latch and by pulling or pushing, you set the angle 0° to
20° on each side.
WARNING
BEFORE MAKING ANY ADJUSTMENTS:
Stop the motor.
Apply parking brake.
Remove the ignition key.
Disconnect the wire from the spark plug(s) and
keep away from spark plug(s) to prevent accidental
starting.
PRESSURE ON THE BRUSH ADJUSTMENT
By turning the adjustment screw (item 1) counter
clockwise, the gauge (item 3) moves higher and the
pressure of the brush on the ground increases. By
turning the adjusting screw clockwise, the gauge
moves lower on the gear box frame and the pressure
of the brush on the ground decreases.
IMPORTANT: Maintain the gauge (item 3) even with
the top of the gear box frame (item 2) or lower for
general hard surface sweeping. Adjust frequently to
compensate for brush wear. Remember to sweep
with the tips of the bristles like a broom and not with
the sides of the bristles like a mop. Too much
pressure can decrease the brush life up to 95%.
WARNING
TO PREVENT INJURIES AND FOR MORE
TRACTION WHEN USING AN ACCESSORY:
-Rear counterweights of 100 lbs. minimum are
required to counter-balance accessory’s weight.
-Tractor manufacturer approved tire chains are
required.
-Do not operate on slopes greater than 10°.
When dismounting an accessory remove rear
counterweights.
GENERAL SWEEPING
Minimize dust by reducing brush speed and by
sweeping after rain or on a day with high moisture.
SNOW SWEEPING
Adjust the gauge (item 3) to be even with the top of
gear box frame (item 2). The broom works well for
light snow removal.
Sweep with the wind blowing in the direction of broom
discharge.
WARNING: Foreign objects in the snow may be
thrown faster than the snow itself.
Frequently clean the snow and ice accumulation from
the top and bottom of the broom hood.
LAWN DETHATCHING AND LEAF RAKING:
Lower the broom on a hard surface and lift the brush
1" from the ground by turning the adjusting screw
clockwise. This adjustment is normally satisfactory
but you may raise or lower depending upon grass
height.
Low brush speed and ground speed is best for lawn
dethatching and leaf raking.
Adjust the pressure on the brush
Never sweep with the sides of
bristles! Sweep with the tips!
Do not mop!
Too much pressure=
Shortens brush life! Road surface
Flick action
9
MAINTENANCE & DISMOUNTING
MAINTENANCE
1. Check oil level in gear box every fifty hours and fill
to plug level with SAE-90-EP oil when necessary.
2. Grease the wheel axles after every eight hours of
use.
3. Roller chain: do not lubricate when used in dusty
conditions. After use, wash clean and lubricate.
4. Adjust the roller chain frequently by moving the
chain idler sprocket to give 1/2" deflection.
5. Frequently clean the interior and exterior of hood.
Dirt, mud, ice, etc, accumulation adds weight on
the brush and could result in premature wear of
brush.
BRUSH REPLACEMENT:
See parts breakdown section for parts identification.
1. Remove the hood (item 53).
2. Loosen the chain idler sprocket (item 24).
3. Remove the bolts (item 22) from both flangettes
(item 68) that holds the brush hollow shaft.
4. Remove the brush hollow shaft (item 52) from the
broom frame (item 31).
5. Loosen the set screw and remove the right bearing
(item 50) from the brush hollow shaft
6. Remove the bolt (item 51) which retains the brush
to the brush hollow shaft.
7. Remove the brush tube from axle.
8. Install the new brush by reversing the procedure.
9. Adjust the tension on the chain by moving the idler
sprocket to give a 1/2" deflection on the chain.
DISMOUNTING
1. Select a level surface, set parking brake, stop
the engine, and remove the ignition key to
prevent accidental starting.
2. Straighten the broom perpendicular with the
tractor.
3. Set the parking stands in their most extended
position Make sure the brush bristles never
touch the ground.
4. Lower the broom to the ground.
5. Remove the hair pin from the handle and remove
handle.
6. Loosen and remove the belt from the tractor
drive pulley and idlers. Disconnect and remove
the driveline if applicable.
7. Detach the broom from the subframe by lifting
the spring locks and pulling back the broom one
side at a time.
8. Remove the rear counterweights.
END OF SEASON STORAGE
1. Clean the broom and inside of the hood and paint
all the parts where the paint has worn off.
2. Take note of the replacement parts needed for
next season.
3. Lubricate all grease fittings and all moving parts.
4. Store broom on parking stands. Make sure the
brush bristles never touch the ground.
5. If brush bristles are exposed to direct sunlight,
protect the bristles with a tarp.
6. Store the broom in a dry place.
BEFORE DOING ANY MAINTENANCE OR
DISMOUNTING AN ACCESSORY, REFER TO THE
SAFETY PRECAUTIONS.
10
TROUBLESHOOTING
PROBLEM POSSIBLE CAUSES CORRECTIVE ACTION
Brush wears out prematurely or
does not wear out evenly.
The brush turns jerkily.
The pressure on the brush is not
well adjusted.
Too much pressure on the brush, it
will wear out up to 5 times faster.
Reduce the pressure on the brush
when on the ground.
Adjust when needed to compensate
for the wearing out of the brush.
Always sweep with the tips of the
bristles like a broom and not with
the sides of the bristles like a mop.
Maintain the gauge even with the
top of the gear box frame or lower
when sweeping hard surfaces.
The brush is too aggressive when
lawn dethatching or leaf raking.
The brush does not turn on the
grass.
Too much pressure on the brush. Lower the broom on a hard surface
and lift brush 1" from the ground by
turning the adjusting screw
clockwise.
Adjust from time to time if
necessary.
The chain wears out prematurely. Inappropriate lubrication. Do not lubricate the chain during
operation. Wait until the job is
finished.
Wash the rotary broom and
lubricate the chain.
Let the broom turn a few moments
so the oil penetrates in the chain.
The brush turns backwards. The belt is not installed in the right
way.
Remove the belt and reinstall as
explained in the subframe Owner’s
Manuel, section broom installation.
Loss of steering. Too much pressure on the brush. Reduce pressure on the brush. If
problem persists, contact your
dealer for more information.
The bristles take a bad form or
shape.
The broom was not stored on the
parking stands.
Wash the broom with warm water or
warm steam. Leave in raised
position and let it turn a few turns.
The brush should take its original
shape.
The brush does not sweep well. Debris accumulation. Clean the inside and outside of the
hood frequently during operation.
Dirt, mud, ice, etc.. accumulation
adds weight on the brush and could
result in premature wear of the
brush.
The sprocket wears out
prematurely.
Chain is not adjusted. Check the chain adjustment
frequently (too tight, too loose).
11
GENERAL TORQUE SPECIFICATION TABLE
USE THE FOLLOWING TORQUES WHEN SPECIAL TORQUES ARE NOT GIVEN
NOTE: These values apply to fasteners as received from supplier, dry or when lubricated with normal oil. They do not apply
if special graphited or moly disulphide greases or other extreme pressure lubricants are used. This applies to both UNF and
UNC threads.
TORQUE SPECIFICATION TABLE
SEE Grade No. 2 5 8 *
BOLT HEAD
IDENTIFICATION
MARKS AS PER GRADE
NOTE MANUFACTURING
MARKS WILL VARY
TORQUE TORQUE TORQUE
BOLT SIZE POUNDS FEET NEWTON-METERS POUNDS FEET NEWTON-METERS POUNDS FEET NEWTON-METERS
Inches Millimetre Min. Max. Min. Max. Min. Max. Min. Max. Min. Max. Min. Max. Max.
1/4" 6.35 5 6 6.8 8.13 911 12.2 14.9 12 15 16.3 30.3
5/16" 7.94 10 12 13.6 16.3 17 20.5 23.1 27.8 24 29 32.5 39.3
3/8" 9.53 20 23 27.1 31.2 35 42 47.5 57 45 54 61 73.2
7/16" 11.11 30 35 40.7 47.4 54 64 73.2 86.8 70 84 94.9 113.9
1/2" 12.7 45 52 61 70.5 80 96 108.5 130.2 110 132 149.2 179
9/16" 14.29 65 75 88.1 101.6 110 132 149.2 179 160 192 217 260.4
5/8" 15.88 95 105 128.7 142.3 150 180 203.4 244.1 220 264 298.3 358
3/4" 19.05 150 185 203.3 250.7 270 324 366.1 439.3 380 456 515.3 618.3
7/8" 22.23 160 200 216.8 271 400 480 542.4 650.9 600 720 813.6 976.3
1" 25.4 250 300 338.8 406.5 580 696 786.5 943.8 900 1080 1220.4 1464.5
*Thick nuts must be used with grade 8 bolts.
METRIC BOLT TORQUE SPECIFICATIONS
COARSE THREAD
Rize Screw Grade No. Pitch (mm) Pounds Feet Newton-Meters Pitch (mm) Pounds Feet Newton-Meters
M6 4T 1.00 3.6 - 5.8 4.9 - 7.9 - - -
7T 5.8 - 9.4 7.9 - 12.7 - -
8T 7.2 - 10 9.8 - 13.6 - -
M8 4T 1.25 7.2 - 14 9.8 - 19 1.00 12 - 17 16.3 - 23
7T 17 - 22 23 - 29.8 19 - 27 25.7 - 36.6
8T 20 - 26 27.1 - 35.2 22 - 31 29.8 - 42
M10 4T 1.50 20 - 25 27.1 - 33.9 1.25 20 - 29 27.1 - 39.3
7T 34 - 40 46.1 - 54.2 35 - 47 47.4 - 63.7
8T 38 - 46 51.5 - 62.3 40 - 52 54.2 - 70.5
M12 4T 1.75 28 - 34 37.9 - 46.1 1.25 31 - 41 42 - 55.6
7T 51 - 59 69.1 - 79.9 56 - 68 75.9 - 92.1
8T 57 - 66 77.2 - 89.4 62 - 75 84 - 101.6
M14 4T 2.00 49 - 56 66.4 - 75.9 1.50 52 - 64 70.5 - 86.7
7T 81 - 93 109.8 - 126 90 - 106 122 - 143.6
8T 96 - 109 130.1 - 147.7 107 - 124 145 - 168
M16 4T 2.00 67 - 77 90.8 - 104.3 1.50 69 - 83 93.5 - 112.5
7T 116 - 130 157.2 - 176.2 120 - 138 162.6 - 187
8T 129 - 145 174.8 - 196.5 140 - 158 189.7 - 214.1
M18 4T 2.00 88 - 100 119.2 - 136 1.50 100 - 117 136 - 158.5
7T 150 - 168 203.3 - 227.6 177 - 199 239.8 - 269.6
8T 175 - 194 237.1 - 262.9 202 - 231 273.7 - 313
M20 4T 2.50 108 - 130 146.3 - 176.2 1.50 132 - 150 178.9 - 203.3
7T 186 - 205 252 - 277.8 206 - 242 279.1 - 327.9
8T 213 - 249 288.6 - 337.4 246 - 289 333.3 - 391.6
FINE THREAD
12
PARTS BREAKDOWN / NOMENCLATURE DES PIÈCES
ROTARY BROOM / BALAI ROTATIF
13
Ref.
Réf. English description Description française Qty.
Qté.
Part #
Pièce #
1Handgrip Poignée 1102062
2Stand holder Support de pied 2102392
3Hex. bolt 1/4" n.c. x 1/2" Boulon hex. 1/4" n.c. x 1/2" 4O/L
4Parking stand Pied de stationnement 2102394
5Caster wheel assembly Roue pivotante assemblée 2105108
6Cap Capuchon 1102586
7Wheel bushing Douille de roue 1103483
8Wheel 6'' included 103482 Roue 6' 'inclue 103482 1103484
9Axle and nut Essieu et écrou 1102372
10 Gear box frame Châssis de la boîte d'engrenage 1104605
11 Gear box Boîte d'engrenage 1102205
12 V pulley Poulie en V 1102043
13 Key 3/16" x 3/16" x 1.000" Clé 3/16" x 3/16" x 1.000" 1102379
14 Key 8 x 7 x 25mm Clé 8 x 7 x 25mm 1102030
15 Gear box guard Garde de la boîte d'engrenage 1102285
16 Hex. bolt 3/8" n.c. x 4" Boulon hex. 3/8" n.c. x 4" 3O/L
17 Delrin bushing Coussinet Delrin 2103482
18 Special washer Rondelle spéciale 1102429
19 Bearing with set screw Roulement à billes avec vis à pression 1102864
20 Drive shaft Arbre de commande 1104063
21 Flange nut 3/8" n.c. Écrou à bride 3/8" n.c. 8O/L
22 Flat washer 7/16" hole Rondelle plate 7/16" trou 4O/L
23 Hex. bolt 3/8" n.c. x 3/4" Boulon hex. 3/8" n.c. x 3/4" 4O/L
24 Spacer Douille 1102286
25 Idler sprocket Pignon tendeur 1102027
26 Spacer Espaceur 1102241
27 Hex. bolt 3/8" n.c. x 2 1/2" Boulon hex 3/8" n.c. x 2 1/2" 1O/L
28 Hex. bolt 5/16" n.c. x 3/4" Boulon hex. 5/16" n.c. x 3/4" 8O/L
29 Carriage bolt 5/16" n.c. x 3/4" Boulon à carrosserie 5/16" n.c. x 3/4" 2O/L
30 Collar Collet 2102402
31 Flange nut 5/16" n.c. Écrou à bride 5/16" n.c. 11 O/L
32 Broom frame Châssis du balai 1104315
33 Roll pin 3/16" x 3/4" Goupille roulée 3/16" x 3/4" 1O/L
34 Rocker arm Culbuteur 1102282
PARTS LIST / LISTE DES PIÈCES
#700316-3
14
Ref.
Réf. English description Description française Qty.
Qté.
Part #
Pièce #
35 Retaining ring Bague de retenue 1102377
36 Latch rod Tige de loquet 1102287
37 Rod link Tige de raccord 1104072
38 Retaining ring Bague de retenue 3102378
39 Latch shaft Arbre du loquet 1102198
40 Cotter pin 5/32" x 1" Goupille fendue 5/32" x 1" 3O/L
41 Spring holder Support de ressort 1102197
42 Spring Ressort 1102201
43 Spring 1/2" Ressort 1/2" 1102003
44 Gauge Jauge 1102367
45 Special nut Écrou spécial 1102288
46 Adjustment screw Vis d'ajustement 1102200
47 Control rod Tige de contrôle 1102291
48 Joint block Bloc de joint 1102275
49 Hair pin 2.5mm Goupille à ressort 2.5mm 5102013
50 Handle Poignée 1102292
51 Bearing with set screw Roulement à billes avec vis à pression 2102755
52 Hex. bolt 5/16" n.c. x 3 1/2" Boulon hex. 5/16" n.c. x 3 1/2" 1O/L
53 Brush hollow shaft Arbre de brosse 1104064
54 Hood Capot 1104316
55 Tapping screw 1/4"-14 x 1/2" Vis taraudeuse 1/4"-14 x 1/2" 8O/L
56 Wheel fork Fourche de roue 1104676
57 Latch Loquet 1102283
58 Flangette Flangette 4102212
59 Flange nut 1/4" n.c. Écrou à bride 1/4" n.c. 4O/L
60 Roller chain #40 x 86 links/conn.link Chaîne # 40 x 86 mailles/maille acc. 1102375
61 Connecting Link #40 Maille d'accouplement #40 1102040
62 Hex. socket set screw 5/16" n.c. x 5/16" Vis à pression hex. 5/16" n.c. x 5/16" 2O/L
63 Lock pin Goupille de barrure 1104677
64 Adaptor pin Goupille adapteur 1104678
PARTS LIST / LISTE DES PIÈCES
#700316-3
15
O/L = Obtain locally/obtenir localement
Ref.
Réf. English description Description française Qty.
Qté.
Part #
Pièce #
65 Spacer Douille d'espacement 1104679
66 Retaining ring Bague de retenue 1102600
67 Bearing Roulement à billes 1102599
68 Nylon insert lock nut 5/8" n.c. (thin) Écrou à garniture de nylon 5/8" n.c. (mince) 1O/L
69 Flangette Flangette 2102680
70 Nylon brush Brosse en nylon 1104065
71 Polypropylene brush Brosse de polypropylène 1104010
72 Important decal Décalque important 1102386
73 Warning decal Décalque warning 1102384
74 Important decal Décalque important 1102387
75 Attention decal Décalque attention 1102385
76 Serial number Numéro de série 1REF
PARTS LIST / LISTE DES PIÈCES
#700316-3
77 Berco decal Décalque Berco 1102471
16
ATTACHMENTS
UTILITY BLADE #700266
Mounts on the same subframe as the
snowblower & rotary broom.
COUNTERWEIGHT
#700240 Universal rear weights
#700246 Rear weights Electrolux
Required for safety and traction.
Counterbalances weight of
attachment.
DUST PROTECTOR
#700452
Especially designed to reduce flying
debris.
ROTARY TILLER #700312
Mounts to the rear of lawn, yard &
garden tractors 14 to 25 HP. Comes
complete with drive & manual lift
mechanisms & mounting hardware.
TRACTOR SCREEN CAB #700424
TRACTOR WINTER CAB #700423
Universal type fits on a wide variety
of lawn and garden tractors.
SNOWBLOWER
#700255 40"
#700210-40"
#700211-44"
Fits on same subframe as rotary
broom and utility blade.
TIRE CHAINS
Two link spacing. Required for
traction and safety.
Pkg. of 2
TRACTOR / A.T.V. SHELTER
#700438
Especially designed to put away your
tractor or A.T.V with it’s accessory.
SIDE WHEEL SUPPORT KIT
#700451
Especially designed for uneven
ground.
NOTES
11
ACCESSOIRES
LAME UTILITAIRE #700266
S’installe sur le même sous-châssis
que la souffleuse & balai rotatif.
CONTREPOIDS
#700240 contrepoids arrière universel.
#700246 contrepoids arrière
Electrolux.
Requis pour une plus grande sécurité
et une meilleure traction.
Contrebalance le poids des
attachements.
CABINE MOUSTIQUAIRE #700424
CABINE D’HIVER #700423
Type universel qui s’adapte sur la
plupart des tracteurs de jardin &
pelouse.
CHAÎNES À PNEUS
Espacement à chaque deux mailles.
Requises pour une meilleure traction
et une plus grande sécurité.
Emb. de 2
PROTECTEUR DE POUSSIÈRE
#700452
Spécialement conçu pour réduire les
objets projetés.
ROTOCULTEUR #700312
S’installe à l’arrière des tracteurs de
pelouse, cours & jardin de 14 à 25
c.v.
Inclus le mécanisme d’entraînement
& de relevage manuel ainsi que le
nécessaire de montage.
SOUFFLEUSE
#700255 40"
#700374-44"
#700378-48"
S’installe sur le même sous-châssis
que le balai rotatif et la lame utilitaire.
ABRI POUR TRACTEUR & V.T.T.
#700438
Spécialement conçu pour remiser
votre tracteur ou V.T.T. avec son
accessoire.
ENSEMBLE DE SUPPORTS DE ROUE
LATÉRALE.
#700451
Spécialement conçu pour les terrains
accidentés.
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
dans d''autres langues
- English: Bercomac 700316-3 User manual
Documents connexes
-
Bercomac BERMXBR60 700632 Manuel utilisateur
-
-
-
-
-
-
-
-
-
