GEARSTONE L80001262 Manuel utilisateur

Catégorie
Accessoires de vélo
Taper
Manuel utilisateur
1-15
16-33
34-51
52-69
70-87
88-105
Home Exercise Bike Instruction Manual
V2021.0.1
1-17
18-35
36-53
54-71
72-89
90-107
-1-
Safety Instructions
Please pay attention to the following matters before installing and
using this exercise bike:
1. Please install in strict accordance with the requirements of the manual.
2. In order to ensure the safety of users, please check whether all the bolts and
other connecting parts on the equipment are locked before each use.
3. Do not expose the equipment to damp places, as this will cause malfunctions.
4. It is best to put the parts on a mat (rubber or wood) during installation to avoid
soiling.
5. Before exercising, make sure that no other items are placed within 2 meters of
the exercise bike.
6. Do not use corrosive detergent when cleaning the machine. Please use the tools
provided with the vehicle or your own special tools to assemble and repair parts.
Also pay attention to wipe off the sweat dripping on the car in time after each exer-
cise.
7. Incorrect or super-intensity exercise is not good for your health. It is recommend-
ed to consult a doctor before exercise, he will set you a maximum amount of exer-
cise (including pulse, watts, duration, etc.), so that you can be on your own exer-
cise and get accurate information. Any strenuous exercise can only start after 40
minutes after a meal.
Note: This bike cannot be used for therapeutic training.
8.You can exercise only when the machine is in a normal state, and you can only
use the accessories provided by the original factory when repairing.
9. This machine can only be used for exercise by one person at a time.
10. It is best to wear sportswear and sports shoes when exercising, and sports
shoes must fit well.
11. If you feel dizzy, vomiting or other bad symptoms during exercise, you should
stop training immediately and see a doctor for consultation.
12. Children and the disabled can only use it under the supervision of someone.
13. This car is designed to adjust the size of the resistance to adjust the speed of
movement, from light to heavy, it can be adjusted back and forth to choose your
suitable resistance.
14. The user's weight cannot exceed 100 kg.
-2-
Exploded View:
TOO L2
TOO L1 TOO L3
-3-
X-BIKE Exploded View List
NO.
Name
Qty
NO.
Name
Qty
1 Front bracket assembly 1 55 Special elastic pin M16 1
2 Rear bracket assembly 1 56 storage box 1
3 Seat cushion tube assembly 1 57 Tighten the bolts 1
4 Front armrest tube assembly 1 58 Support adjustment tube 1
5 Front leg assembly 1 59 Cylindrical pin 1
6 Rear leg assembly 1 60 Round pipe inner plug 2
7 Intermediate rotation group 1 61 Pan Head Hexagon Bolt 1
8 Cushion connecting pipe assembly 1 62 Flat pad 1
9 Cushion fixing pipe assembly 1 63 Locknut 3
10 Rear armrest tube assembly 1 64 Pan Head Hexagon Bolt 4
11 Belt pulley assembly 1 65 Spring cushion 4
12 Cast iron wheel 1 66 Electronic watch cover 1
13 Circlip for shaft 6 67 Round pipe inner plug 4
14 Bearing seat 2 68 Thread plug 4
15 Bearing 4 69 Left pedal nut (left tooth) 1
16 Bearing cap 2 70 Right pedal nut (right tooth) 1
17 Phillips pan head screws 6 71 Center lock flange nut 2
18 Wave washers 5 72 Crank plug 2
19 driven wheel 1 73 Phillips pan head tapping screws 4
20 Bearing 2 74 Phillips pan head tapping and self-drilling screws 6
21 Plastic spacer 1 75 Belt 1
22 Driven shaft 1 76 Belt 1
23 Draw bolt 2 77 Cap nut 5
24 Draw bolt U-shaped baffle 2 78 Enlarged arc gasket 6
25 Locknut 2 79 Left front foot plug assembly 1
26 Hex nuts 2 80 Front foot right plug assembly 1
27 Circlip for shaft 1 81 Round pipe outer plug 2
28 Wave spring cushion 1 82 Sponge grip 2
29 Hexagon thin nuts 1 83 Bushing between pipes 1
30 Circlip for shaft 1 84 M8 lock nut 3
31 Bearing 1 85 Flat pad 3
32 Pinch roller shaft 1 86 cushion 1
33 Increase flat pad 1 87 Pan head square neck bolts 2
34 Locknut 1 88 Pan Head Hexagon Bolt 2
35 Magnet frame assembly 1 89 Sponge grip 2
36 magnet 6 90 Pan Head Hexagon Bolt 1
37 Cross flat head bolt 1 91 Plastic flat pad 2
38 spring 1 92 Square tube plug 1
39 Cross pan head bolts 2 93 Square tube plug 4
40 Sensor base 1 94 Pan Head Hexagon Bolt 4
41 Left pedal 1 95 Spring cushion 4
42 Right pedal 1 96 Cushion 1
43 Left crank 1 97 Limit plug 1
44 Right crank 1 98 Phillips pan head tapping screws 2
45 Left protective cover 1 99 Cross pan head bolts 1
46 Line plug-2 1 100 Increase flat pad 1
47 Right protective cover 1 101 Phillips pan head tapping screws 2
48 Electronic watch back cover 1 102 Phillips pan head tapping and self-drilling screws 1
49 Middle protective cover 1 103 Magnet holder 1
50 Plastic bushing 6 104 Eight-speed fine-tuning 1
51 Pan Head Hexagon Bolt 2 105 Phillips tapping screws 1
52 Increase flat pad 6 106 Pulse seat 2
53 transmission shaft 1 107 Flat pad 2
54 M10 fixed pin special 1 108 Phillips pan head tapping screws 2
7
8
0
0
6
-4-
Step 1:
Take out the product out of the box as shown in Figure 1;
Pull the special elastic pin (55) outward and unfold the body as shown in Figure 2.
-5-
Step 2:
TOOL2
1. Use TOOL 2 with cap nut (77) to enlarge the arc-shaped washer(78) Fix the
front leg tube (5) to the front bracket (1), and lock it tight.
2. Use TOOL 2, cooperate with the cap nut (77) to enlarge the arc-shaped washer
(78), fix the rear leg tube (6) to the rear bracket (2), and lock it.
-6-
Step 3:
TOOL2TOOL3
1. Using TOOL 2, screw the left pedal (41) into the left crank, and then cooperate
with TOOL3 to tighten the left pedal nut (69).
2.Using TOOL 2, screw the right pedal (42) into the right crank, and then cooperate
with TOOL3 to tighten the right pedal nut (70).
Note: Please pay attention to the direction of the arrow during tightening.
-7-
Step 4:
T O O L1
1. Insert the front armrest assembly (4) into the rear bracket tube (2), use TOOL 1,
and cooperate with the pan-head hexagon socket bolt (64) spring washer (65) to fix
the front armrest assembly (4) to the front bracket (2) .
2: Connect the electronic meter connector (A/B) and click into place (as shown in
the figure)
-8-
Step 5:
TOOL2
1.Using TOOL 2, fit the seat cushion (86) with the lock nut (84) The gasket (85) is
fixed on the cushion tube.
2.Insert the locked seat tube (3) into the front bracket (1), and fix it with the tighten-
ing bolt (57).
-9-
Step 6:
1: Use TOOL 1 to fix the back cushion (96) on the back cushion tube (9) with the
pan head hexagon socket bolt (94) and spring washer (95).
2: Use TOOL 1 and TOOL 2, and cooperate with the pan-head hexagon socket bolt
(94) to enlarge the arc-shaped cushion (78) and the cap nut (77), and fix the rear
armrest (10) to the back cushion connecting pipe (8).
3: Use TOOL 2, cooperate with the pan-head square neck bolt (87) to enlarge the
flat washer (52) and lock nut (63), and fix the locked cushion connecting tube (8) to
the cushion tube (3).
T O O L1
T O O L2
-10-
Finished :
The product assembly is completed.
Please install the battery of the electronic watch before use, and remove the bat-
tery when not in use for a long time.
Before use, please be sure to check whether all the connections are fully locked
before moving.
-11-
Exercise Bike Status:
Pull the special elastic pin (55) outwards and unfold the body to make the special
elastic pin (55) snap into hole B.
-12-
Lazy Bike Status:
Pull the special elastic pin (55) outward and unfold the body so that the special
elastic pin (55) fits into the hole A.
Collapse status:
Pull the special elastic pin (55) outward and unfold the body so that the special
elastic pin (55) fits into the hole C.
-13-
-14-
EXERCISE COMPUTER INSTRUCTION MANUAL
FUNCTIONAL BUTTON:
MODE : Push down to select functions, (SCAN),(TIME),(SPEED),(DIST),(ODO),
(CAL),
RESET : Push down to reset timedistance and calories for 2 seconds.
FUNCTIONS AND OPERATIONS
1. SCAN: Press MODE button until “SCAN” appears, monitor will rotate through the
following functions: timespeed distance calories odometer and pulse,
each display will be hold 6 seconds.
2. TIME : Count the total time from exercise start to end.
3. SPEED: Display current speed.
4. DISTANCE: Count the distance from exercise start to end.
5. CALORIES: Count the total calories from exercise start to end.
6. ODOMETERTOTAL DISTMonitor will display the total accumulated dis
tance, after the battery is reinstalled, the value will return to zero.
7. PULSE RATE: Measure the user's heart rate.Press the button to switch to the
pulse function, and hold the two heartbeat sensors in both hands to measure the
heart rate.
Remark: During the process of pulse measurement, because of the contact jam-
ming, the measurement value may be higher than the virtual pulse rate during the
first 2~3 seconds, then will return to normal level. The measurement value can not
be regarded as the basis of medical treatment.
NOTE
1. If the display is faint or shows no figures ,please replace the batteries.
2. The monitor will automatically shut off if there is no signal received after 4 min
utes .
3. The monitor will be auto powered on when starting to exercise push button
signal in.
4. The monitor will automatically start calculating when you start to exercise and
will stop calculating when you stop exercising for 4 seconds .
-15-
FUNCTION
AUTO SCAN
Every 6 seconds
TIME
0:00’~99:59’
CURRENT SPEED
0.0~999.9 KM/HMILE/H
TRIP DISTANCE
0.00~999.9 KM
MILE
CALORIES
0.0~999.9 CAL
ODOMETER
0.0~9999 KM
MILE
PULSE RATE 40~240 BPM
BATTERY TYPE 2pcs of SIZE –AAA or UM –4
0°C ~ +40°C
STORAGE TEMPERATURE -10°C ~ +60°C
SPECIFICATIONS:
Sports Description
Using a multi-functional abdomen machine can bring you many benefits, it can
improve your physical health, strengthen muscles, and control diet calories can
help you lose weight.
1. Warm-up Stage
This stage helps blood flow around the body and allows the muscles to work
normally. It also reduces the risk of cramps and muscle damage. It is recom-
mended to do some stretching exercises as shown below. Each stretch should
be maintained for about 30 seconds. Do not force or jerk your muscles. If you
feel pain, stop immediately.
-16-
2. Exercise Stage
This is the stage where you work hard. After regular use, the leg muscles will
become more flexible. It is very important to maintain a steady rhythm throughout
the process. The speed of movement should be enough to make your heartbeat
reach the target area shown in the figure below.
This stage should last at least 12 minutes, most people 15-20 minutes
3.Relaxation Stage
This stage is to relax your cardiovascular system and muscles. This is a repe-
tition of a warm-up exercise, such as slowing down your rhythm for about 5
minutes. The stretching exercise should be repeated now, again remember
not to force or pull your muscles into the stretch.
When you become healthier, you may need to train longer and harder. It is
wise to train at least three times a week, and if possible, schedule your exer-
cises evenly throughout the week.
4.Muscle sculpting
In order to exercise muscles on your abdomen machine, you need to set a
fairly high resistance. This will put more pressure on our leg muscles and
may mean that you can't train as long as you think. If you also want to
improve your fitness level, you need to change your training plan. During the
warm-up and cooling phase, you should train as usual, but at the end of the
exercise phase, you should increase the resistance to make your legs work
harder. You will have to reduce your speed to keep your heart rate in the
target zone.
Heart rate
Target zone
Max
Slow-down
Age
-17-
Lose Weight
The important factor here is the effort you put in. The harder you exercise and
the longer it takes, the more calories you burn. Effectively speaking, it's like you
are training to improve your physical fitness, but the goal is different.
-18-
Sicherheitshinweise
Beachten Sie vor der Installation und Verwendung dieses Heim-
trainers Folgendes:
1. Installieren Sie in strikter Übereinstimmung mit den Anforderungen des Hand-
buchs;
2. Um die Sicherheit der Benutzer zu gewährleisten, überprüfen Sie, ob alle
Schrauben und andere Verbindungsteile vor jedem Gebrauch an der Ausrüstung
verriegelt sind;
3. Setzen Sie das Gerät nicht feuchten Stellen aus, da dies zu Fehlfunktionen
führen kann;
4. Es ist am besten, die Teile auf einer Matte (Gummi oder Holz) zum Zeitpunkt der
Installation zu platzieren, um eine Kontamination zu verhindern;
5. Prüfen Sie vor dem Training, dass sich keine anderen Gegenstände innerhalb
von 2 Metern vom Heimtrainer befinden;
6. Verwenden Sie kein beißendes Reinigungsmittel, um die Maschine zu reinigen.
Verwenden Sie die mitgelieferten Werkzeuge oder Ihre eigenen Spezialwerkzeuge,
um Teile zu montieren und zu reparieren. Stellen Sie außerdem sicher, dass Sie
nach jeder Übung den Schweiß, der auf das Gerätfällt, rechtzeitigabwischen;
7. Falsches oder superintensives Training ist nicht gut für Ihre Gesundheit. Es wird
empfohlen, vor dem Training einen Arzt aufzusuchen. Er wird eine maximale
Menge an Training für Sie (einschließlich Puls, Wattleistung, Dauer, etc.) Auf diese
Weise können Sie sich selbst trainieren und genaueInformationen erhalten. Jede
anstrengende Übung kann erst nach 40 Minuten nach dem Essen beginnen.
Hinweis: des Gerät kann nicht für therapeutische Ausbildung verwendet werden;
8. Sie können nur trainieren, wenn die Maschine in einem normalen Zustand ist,
und Sie können nur das Zubehör verwenden, das von der ursprünglichen Fabrik
bei der Reparatur zur Verfügung gestellt wird;
9. Diese Maschine kann nur von einer Person zu einer Zeit für die Praxis verwen-
det werden;
10. Es ist am besten, Sportbekleidung und Sportschuhe während des Trainings zu
tragen, und Sportschuhe sollten gut passen;
11. Wenn Sie während des Trainings Schwindelgefühle, Erbrechen oder andere
Symptome empfinden, sollten Sie sofort mit dem Training aufhören und einen Arzt
zur Konsultation konsultieren;
12. Kinder und Behinderte dürfen sie nur unter Aufsicht einer Person benutzen;
13. D es Gerät ist entworfen, um die wzuerst einzustellen und die Geschwindigkeit
derBewegung einzustellen, von leicht bis schwer, kann es hin und her eingestellt
werden, um Ihren geeigneten Widerstand zu wählen;
14. Das Gewicht des Nutzers darf 100 kg nicht überschreiten;
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109

GEARSTONE L80001262 Manuel utilisateur

Catégorie
Accessoires de vélo
Taper
Manuel utilisateur