Landxcape LX793 Le manuel du propriétaire

LX790 LX791

LX792 LX793

P09

P22

P37

P51

P64

P78

P91

P105

P119

P131

P144

P158

P172

P185

EN

D

F

I

ES

NL

PL

HU

RO

CZ

SK

PT

TR

SL

Owner’s Manual

Benutzerhandbuch

Mode d’emploi

Manuale d’uso

Manual del propietario

Gebruikershandleiding



Felhasználói kézikönyv

Manual utilizator





Manual de utilizador



Navodila za uporabo

Original instructions EN

Originalbetriebsanleitung D

Notice originale F

Istruzioni originali I

Manual original ES

Oorspronkelijke gebruiksaanwijzing NL

Instrukcja oryginalna PL

Eredeti használati utasítás HU

 RO

 CZ

 SK

Manual original PT

 TR

 SL

127 8

21

20

9 10

11

12

13

14

15

16

17

18 19

22 23 24

3 4

6

5

A

C

B

DD

E1

E2 F

G

H

K2

K1

K3

1

2

L

I

J

M

N

O1

O2

P

Q1

Q3

Q5Q4

Q2

1

2 2

EN 9

1. Product Safety

1.1 General & Additional Safety Instruction

WARNING: Read all safety warnings and all instructions.

Failure to follow the warnings and instructions may result in

electric shock, fire and/or serious injury.

Carefully read the instructions for the safe operation of the

machine.

Save all warnings and instructions for future reference.

• This appliance is not intended for use by persons (including

children) with reduced physical, sensory or mental capabilities, or

lack of experience and knowledge, unless they have been given

supervision or instruction concerning use of the appliance by a

person responsible for their safety.

• Children should be supervised to ensure that they do not play with

the appliance.

• The appliance is only to be used with the power supply unit

provided with the appliance.

IMPORTANT

READ CAREFULLY BEFORE USE

KEEP FOR FUTURE REFERENCE

SAFE OPERATION PRACTICES

Training

a) Read the instructions carefully. Make sure you understand the

instructions and be familiar with the controls and the proper use of

the appliance;

b) Never allow people unfamiliar with these instructions or children

to use the appliance. Local regulations can restrict the age of the

operator;

c) The operator or user is responsible for accidents or hazards

occurring to other people or their property.

Preparation

a) Ensure the correct installation of the boundary wire as instructed.

b) Periodically inspect the area where the appliance is to be used and

remove all stones, sticks, wires, bones, and other foreign objects.

c) Periodically visually inspect to see that the blades, blade bolts

and cutter assembly are not worn or damaged. Replace worn or

damaged blades and bolts in sets to preserve balance.

d) On multi-spindle appliances, take care as rotating one blade can

cause other blades to rotate.

e) WARNING! The lawnmower shall not be operated without the guard

in place.

OPERATION

1. GENERAL

a) Never operate the appliance with defective guards, or without

safety devices, for example deflectors, in place.

b) Do not put hands or feet near or under rotating parts. Keep clear of

the discharge opening at all times.

c) Never pick up or carry an appliance while the motor is running.

d) Operate the disabling device from the appliance.

- Before clearing a blockage;

- Before checking, cleaning or working on the appliance.

e) It is not permitted to modify the original design of robotic

lawnmower. All modifications are made at your own risk.

f) Start robotic lawnmower according to the instructions. When the

power key is switched on, make sure you keep your hands and

feet away from the rotating blades. Never put your hands and feet

under the mower.

g) Never lift up robotic lawnmower or carry it when the power key is

switched on.

h) Do not let persons who do not know how robotic lawnmower

works and behaves use the mower.

i) Do not put anything on top of robotic lawnmower or its charging

station.

j) Do not allow robotic lawnmower to be used with a defective blade

disc or body. Neither should it be used with defective blades,

screws, nuts or cables.

k) Always switch off robotic lawnmower when you do not intend to

use the mower. Robotic lawnmower can only start when the power

key is switched on and the correct PIN code has been entered.

l) Keep your hands and feet away from the rotating blades. Never

place your hands or feet close to or under the body when robotic

lawnmower is in operation.

m) To avoid using the machine and its peripherals in bad weather

conditions especially when there is a risk of lightning.

n) Not to touch moving hazardous parts before these have come to a

complete stop.

o) For machines used in public areas, that warning signs shall be

placed around the working area of the machine. They shall show

the substance of the following text:

WARNING!

Automatic lawnmower! Keep away from the

machine! Supervise children!

2. ADDITIONALLY WHEN THE APPLIANCE IS OPERATING

AUTOMATICALLY

a) Do not leave the machine to operate unattended if you know that

there are pets, children or people in the vicinity.

MAINTENANCE AND STORAGE

When the mower is turned upside down the power key must

always be switched off.

The power key should be switched off during all work on the

mower’s underframe, such as cleaning or replacing the blades.

a) Keep all nuts, bolts and screws tight to be sure the appliance is in

safe working condition.

b) Inspect the robotic lawnmower each week and replace worn or

damaged parts for safety.

c) Check especially that the blades and blade disc are not damaged.

Replace all blades and screws at the same time if necessary so

that the rotating parts are balanced.

d) Ensure that only replacement cutting means of the right type are

used.

e) Ensure that batteries are charged using the correct charger

recommended by the manufacturer. Incorrect use may result in

electric shock, overheating or leakage of corrosive liquid from the

battery.

f) In the event of leakage of electrolyte flush with water/neutralizing

agent, seek medical help if it comes into contact with the eyes etc.

g) Servicing of the appliance should be according to manufacturers’

instructions.

Recommendation

To connect the machine and/or its peripherals only to a supply circuit

protected by a residual current device (RCD ) with a tripping current of

not more than 30 mA.

EN10

Residual risks

To avoid injuries, wear protective gloves when replacing the blades.

Transport

The original packaging should be used when transporting robotic

lawnmower over long distances.

To safely move from or within the working area:

a) Press the STOP button to stop the mower.

You select the four digit PIN code when you start the mower for the

first time.

b) Always switch off robotic lawnmower if you intend to carry the

mower.

c) Carry the mower by the handle at the front under the mower. Carry

the mower with the blade disc away from the body.

Safety Warnings for battery pack inside the tool

a) Do not dismantle, open or shred battery pack.

b) Do not short-circuit a battery pack. Do not store battery

packs haphazardly in a box or drawer where they may short-

circuit each other or be short-circuited by conductive

materials.

When battery pack is not in use, keep it away from

other metal objects, like paper clips, coins, keys, nails, screws or

other small metal objects, that can make a connection from one

terminal to another. Shorting the battery terminals together may

cause burns or a fire.

 

direct sunlight.

d) Do not subject battery pack to mechanical shock.

e) In the event of battery leaking, do not allow the liquid to

come into contact with the skin or eyes. If contact has been

made, wash the affected area with copious amounts of water

and seek medical advice.

f) Seek medical advice immediately if a cell or battery pack

has been swallowed.

g) Keep battery pack clean and dry.

h) Battery pack gives its best performance when it is operated

at normal room temperature (20 °C ± 5 °C).

i) When disposing of battery packs, keep battery packs of

different electrochemical systems separate from each

other.

 

TM

.



for use with the equipment. A charger that is suitable for one



another battery pack.

k) Do not use any battery pack which is not designed for use

with the equipment.

l) Keep battery pack out of the reach of children.

m) Retain the original product literature for future reference.

n) Dispose of properly.

2. Information on the Landxcape

TM

WARNING - Robotic lawnmower can be dangerous if

incorrectly used.

Read through the Operator’s manual carefully and

understand the content before using your robotic

lawnmower.

WARNING - Keep a safe distance from the machine

when operating.

WARNING – Operate the disabling device before

working on or lifting the machine.

WARNING - Do not ride on the machine.

Do not burn

Do not expose to rain or water.

Do not dispose of batteries. Return exhausted

batteries to your local collection or recycling point.

Do not wash the machine with a high pressure

washer

Class III appliance

Waste electrical products must not be disposed of

with household waste. Please recycle where facilities

exist. Check with your local authorities or retailer for

recycling advice.

EN 11

1. STOP BUTTON

2. CUTTING HEIGHT ADJUSTMENT KNOB

3. ON/OFF KEY

4. START KEY

5. HOME BUTTON

6. DISPLAY

7. CHARGING STRIPS

8. RAIN SENSOR

9. FRONT WHEEL

10. BLADE TURNING DISC

11. CUTTING BLADE

12. BATTERY PACK

13. USB PORT

14. REAR DRIVING WHEEL

15. HANDLE

16. CONTACT PINS

17. CHARGING BASE

18. POWER ADAPTER

19. WIRE PEGS

20. BOUNDARY WIRE

21. CHARGING BASE FIXING NAILS

22. BOUNDARY WIRE DISTANCE GAUGE

23. HEX KEY

24. CONNECTOR

Not all the accessories illustrated or described are included in standard delivery.

2. Component List

EN12

3. Technical data and noise data

3.1 Technical data

Type LX790 LX791 LX792 LX793 (790-799 - designation of

machinery, representative of Robotic Lawn mower)

LX790 LX792 LX791 LX793

Rated voltage 20V

Max.*

No load speed 2800/min

Cutting area 600m

2

900m

2

Cutting diameter 16cm 18cm

Cutting height 30-60mm

Cutting height positions 4

Battery type Lithium-ion

Battery model LA0001 LA0002

Charging time approx. 1.3hrs 2hrs

Charger model LA8001 / LA8002

Charger rating

Input: 100-240V~50/60Hz, 38W,

Output: 20V

, 1.5A

Machinery weight 8.4kg

Protection degree III

*Voltage measured at no load. Initial battery voltage reaches maximum

of 20 volts. Nominal voltage is 18 volts.

Accessories

LX790 LX792 LX791 LX793

Screw 9 9

Charging base 1 1

Charging base fixing nails 7 7

Boundary wire 150m 180m

Wire pegs 210 250

Hex key 1 1

Boundary wire distance gauge 2 2

Blade 9 9

Connector 2 2

Battery pack (LA0001/ LA0002) 1 1

Charger (LA8001 / LA8002) 1 1

We recommend that you purchase genuine accessories listed in the

above list from the same store that sold you the tool. Refer to the

accessory packaging for further details. Store personnel can assist you

and offer advice.

3.2

Noise data

A weighted sound pressure L

pA

= 44.2dB (A), K

PA

= 0.4dB(A)

A weighted sound power

L

wA

= 64.2dB (A) K

wA

= 0.4dB(A)

Wear ear protection when

sound pressure is over

80dB(A)

A degree of noise from the machine is not avoidable. Route noisy work

is to be licensed and limits for certain periods. Keep rest periods and

they may need to restrict the working hours to a minimum. For their

personal protection and protection of people working nearby, an ap-

propriate hearing protection shall be worn.

Intended Use

The garden product is intended for domestic lawn mowing. It is de-

signed to mow often, maintaining a healthier and better looking lawn

than ever before. Depending on the size of your lawn, your Landxcape

TM

may be programmed to operate at any time or frequency. It is impos-

sible for digging, sweeping or snow cleaning.

EN 13

4. Control panel

Start

1) After the boundary wire installation, you can start using Landxcape

TM

(Please refer to Installation Guide for boundary wire installation).

2) Press

until Landxcape

TM

turns on. For the first use, input the default PIN code 0000 by pressing for four times when the number 0 is

blinking. (The PIN code can be changed, please refer to “Setting” in the Installation Guide).

NOTE:

Landxcape

TM

will turn off if it does not receive any input within 30 seconds after it is turned on. If you enter wrong PIN code three times,

Landxcape

TM

will raise the alarm “di-di” and then turn off.

3) Press

, then press to start mowing.

4) Press then to make Landxcape

TM

go to the charging base, with the blades rotating to cut grass on the way home.

Landxcape

TM

will work continuously until reaching low battery power level and then it will return to the charging base. Once charging is complete,

Landxcape

TM

will automatically resume mowing or it stay in the charging base according to the mowing schedule.

NOTE:

When Landxcape

TM

turns on, all lights on the display will be illuminated and then turn off. Check if there is any light damaged. It is

recommended to shield the display with your hand when the outdoor light gets too strong.

POWER ON/OFF

Turns Landxcape

TM

on

and off

LOCK

BATTERY CAPACITY

Working time

START

Starts mowing/

Selects up

STANDBY PAGE:

Landxcape

TM

is not in the

working hours.

SLEEP PAGE:

Landxcape

TM

is fully charged and is

not in the working hours.

DISPLAY

Displays the state of your setting

STOP

Stops Landxcape

TM

during

operation

HOME

Sends Landxcape to its

charging base during

operation with the blades

rotating to cut grass

on the way home and

activates charging/Selects

down

OK

Confirms any setting

EN14

5. Understanding Your Landxcape

TM

Congratulations on your new purchase of Landxcape

TM

and welcome

to the care-free life of automatic mowing. In the following, we want to

help you to better understand how your Landxcape

TM

thinks.

5.1 How does my Landxcape

TM

know what

to mow?

Landxcape

TM

chooses its direction at random. It will make sure your

entire lawn is evenly mowed without leaving unattractive mowing paths

(See Fig. A).

5.2 How does my Landxcape

TM

know where

to go?

Your Landxcape

TM

is made to work on its own. Landxcape

TM

knows

when it needs to go to its charging base to charge, can sense when it is

raining, can stop itself if it senses a problem, and knows to stop, draw

back, and turn around when it bumps into something blocking its path.

Landxcape

TM

will also automatically stop its blade turning disc from

rotating if it is lifted off the ground to prevent an accident.

A. Finding the Charging Base

When your Landxcape

TM

needs to recharge, it will stop mowing and

follow the boundary wire in an anti-clockwise direction back to its

charging base. Landxcape

TM

is pre-programmed to mow the grass near

the boundary wire twice a week. By default, Landxcape

TM

will mow near

the boundary wire every Monday and Friday after it is powered on.

B. Rain sensors

Landxcape

TM

is equipped with a rain sensor which detects rain and tells

Landxcape

TM

to stop mowing and follow the boundary wire back to its

charging base (See Fig. B).

Landxcape

TM

will resume mowing after passing the delay time. The

default delay time is 180mins.

When the rain sensors are wet,

Landxcape

TM

returns to its charging

base. When the rain sensors are dry,

Landxcape

TM

will begin the delay

time countdown. If you want to exit from the rain delay, dry the sensor

area, and perform a power cycle by operating the on/off key. After the

power cycle has been performed, you can operate again.

C. Sensing the boundary wire

Landxcape

TM

always obeys the border set by the boundary wire and

uses sensors at its front to detect it. (See Fig. C)

D. Starting and stopping while mowing (See Fig. D, E1, E2)

To start mowing, press the on/off key and input the PIN code. Press

, then press . If you would like

Landxcape

TM

to stop mowing, simply

press the STOP button on top of the mower.

If

Landxcape

TM

senses something is wrong, it will display a fault message

on the display. For information on these messages, refer to the Error

Messages.

Landxcape

TM

will turn off if it does not receive any input from

the user within 20 minutes.

To resume:

• Press , then press

• Now Landxcape

TM

will begin to mow!

5.3 Setting

First please set the height to a desired grass level after cut and you can

do the program setting manually.

NOTE: When doing the program setting manually, Landxcape

TM

will

enter the standby page if it does not receive any input from the user

within 30 seconds.

(1) Change PIN code

To change the PIN code, keep pressing both

and buttons at the

same time for 5 seconds. The icon will be blinking, and “ ” will

be rolling ﬂashing. After that, the ﬁrst number will be blinking, use or

to select the number you want and press to conﬁrm. The next

number will be blinking. Use the same method to complete other numbers.

For example, the new PIN code is set to be 0326. After that, “ ”

will be rolling ﬂashing and the ﬁrst number will be blinking again. Use the

same method to input the new PIN code you set just now (in this example,

). Then “ ” will be rolling ﬂashing on the display.

Your PIN code has been changed successfully.

Only for reference

(2) Set year, date and time

Set year, date and time are compulsory setting items. If you don’t set these

items, it will inﬂuence the schedule time in the following setting. These

items should be set in the order of year, date and time. For the year setting,

keep pressing

for 3 seconds until the icon and a number are

blinking on the display, for example, . Use or to select

the year you want. Then press to conﬁrm to ﬁnish the year setting.

Only for reference

EN 15

Meanwhile, the icon

will be ﬂashing again and a number will be

displayed to indicate the date, for example, , meaning September

29. When is ﬂashing, use or to select the number and press

to conﬁrm. Then will be ﬂashing. Use the same method to select

the number and press to conﬁrm to ﬁnish the date setting.

Only for reference

Meanwhile, the icon

will be ﬂashing and the time will be displayed,

for example, . When is blinking, use or to to select

the number and press to conﬁrm. Then will be blinking, use the

same method to select the number and press to conﬁrm. Now the

time setting is completed and Landxcape

TM

will enter the standby page.

Only for reference

(3) Set work area

Keep pressing

for 3 seconds. When the icon is blinking, press

. A number will be blinking on the display, for example, , which

is the lawn area. The working time will be automatically set according to

the size of your garden. Use or to set the lawn area (the area will

increase / decrease by 50m

2

each time the / is pressed), and

press to conﬁrm. Then Landxcape

TM

will enter the standby page.

Only for reference

(4) Change default start time

The default start time of 9:00 can be changed to anytime by keep pressing

both

and buttons at the same time until a ding sound is heard.

For example, keep pressing both and buttons at 14:05, and

your Landxcape

TM

will start mowing from 14:05.

Only for reference

5.4 How efficiently will my Landxcape

TM

mow the grass?

Mowing times are different for every lawn depending on the factors

mentioned below. Gradually adjust the time you allow Landxcape

TM

to

mow each day until you find the most suitable setting.

Your Landxcape

TM

is capable of mowing areas of different sizes,

although this depends on various factors, such as:

• Species of grass in your lawn and its growth rate

• Sharpness of the cutting blades

• Humidity

• Surrounding temperature

• Amount of obstacles in your Lawn

Unlike most other mowers,

Landxcape

TM

uses a side charging system,

which is able to cut the surrounding grass as much as possible. The holes

on the bottom of the charging base allow the grass to grow through the

base to help disguise it and create an elegant appearance.

Landxcape

TM

’s cutting height can be adjusted between 3cm-6cm. Before

starting your Landxcape

TM

for the first time, you should cut the grass to

the height no more than 9 cm with your manual lawnmower. Then, set the

cutting height of your Landxcape

TM

to its maximum setting (6cm) for its

first time mowing. (See Fig. F)

Your Landxcape

TM

will cut best in dry weather. Wet grass can build up

on the blade turning disc and within the motor, and can also cause

loose traction and slippage while working.Your Landxcape

TM

is afraid of

lightning storms. In case of a lightning storm, protect Landxcape

TM

by

unplugging the charging base, disconnecting the boundary wire, and

making sure Landxcape

TM

is not allowed to charge.

Your Landxcape

TM

loves mowing grass and requires the cutting blades

to be kept in good condition to cut at its best. Landxcape

TM

can do most

things by itself, but will sometimes need your help to prevent damage

to itself.

• Never let Landxcape

TM

travel over gravel.

• Remove or prevent access to obstacles that Landxcape

TM

could

accidentally climb on and damage its blade turning disc.

• Remove all debris and foreign objects from your lawn.

6. Boundary Wire Basics

6.1. Pegging the Boundary Wire

Use the boundary wire distance gauge to set the correct distance

between the wire and the border of your lawn (more than 26cm).This

is the recommended distance. The provided distance gauge ensures

proper installation.

If your neighbor also uses a Landxcape

TM

, keep a spacing of at least 1

metre between your boundary wire and your neighbor’s.

The boundary wire must outline the intended mowing area

EN16

exactly.

Your Landxcape

TM

will become confused by extra bends or

coils of boundary wire that are not part of its mowing area (See Fig.

G). If there is excess boundary wire after the mowing area has been

outlined, cut it off and store this additional wire in a separate location.

It is important to leave the necessary length where it connects to the

charging base so it can be connected and still remain buried.

6.2 Burying the Boundary Wire

If you are planning to bury the boundary wire, it is recommended to first

peg it down. This allows you to easily change the layout if necessary before

burying the wire. When the boundary wire installation is complete, have

Landxcape

TM

follow and check the path by pressing and . This

allows your

Landxcape

TM

to adjust to its new environment. .

While observing

Landxcape

TM

you can easily make alterations to the

boundary wire to ensure

Landxcape

TM

's trouble-free tracking when locating

the charging station. Confirm that

Landxcape

TM

docks in the charging

station successfully, and bury the wire if desired.

6.3 Joining the boundary wire

If you want to extend and splice the boundary wire, use a connector.

The connector is waterproof and provides optimal connection.

Insert both wire ends in any two of the three holes of the connector.

Insert the wires fully until both wire ends are visible on the other side of

the connector. (See Fig. H) Press the connector together by using a pair

of pliers. (See Fig. I, J)

WARNING!

It is not recommended to simply splice the boundary

wire with insulating tape or use a screw terminal block for

connection. A broken circuit may occur after a period of time as soil

moisture can oxidize the wire.

7. Software update

The software can be updated when new versions become available.

The latest software can be downloaded from our website

www.landxcape-robotics.com.

Update via USB. See below for download and installation instructions:

(1) Locate the latest software version at: www.landxcape-robotics.

com. Save the file to an empty

FAT32

formatted USB (flash drive).

Delete any other files on the drive and check the format. If the drive

is not formatted in

FAT32

, please reformat the drive.

NOTE:

the software update is downloaded as a zipped file. You will

need to unzip or extract it before proceeding.

(2) Place Landxcape

TM

on a secure and level surface. Press

to turn

off your Landxcape

TM

.

(3) Insert the USB drive (flash drive) in the port. (See Fig. K1)

(4) Turn Landxcape

TM

on. The update will begin automatically. Wait until

the display shows “ ” (See Fig. K2), then remove the USB drive

(flash drive) and tightly close the protective cover. When the display

shows “ ”, the update is complete and Landxcape

TM

will enter

the PIN page.

The manual included with your Landxcape

TM

is based on the default

software at the time of production. Some new features/functions in the

new version may not exist in the manual. If you found some settings not

in the manual, please visit www.landxcape-robotics.com to download

the latest manual.

8. Maintenance

Your Landxcape

TM

works hard and needs to be cleaned and checked

from time to time. Some parts will require replacement as they become

worn. Never use your Landxcape

TM

with defective main switch.

Switch off the machine before carrying out any service or maintenance.

Here's how to take care of your Landxcape

TM

.

8.1 Keep it sharp

WARNING: Before cleaning, adjusting, or replacing the

blades, turn your Landxcape

TM

OFF and put on protective

gloves.

WARNING: When fitting new blades, make sure you

replace ALL the blades. Always use new screws when

fitting blades. This is important to ensure blade retention and

balance the blade turning disc. Failure to use new screws could

cause serious injury.

Landxcape

TM

does not cut grass like other mowers. Its cutting blades

are razor sharp on 2 edges and rotate in both directions for maximum

cutting capacity (See Fig. L). Each blade of your

Landxcape

TM

has 2

cutting edges. The blade turning disc will make forward and reverse

rotation at random to use both cutting edges and minimize the

frequency of replacing the blades. Each cutting blade will last up to

2 months when it is programmed to mow everyday. Always check to

see if the blades are chipped or damaged and replace them if they

are. When the cutting blades are dull and worn out, they should be

replaced with the spare blades provided with your

Landxcape

TM

. Spare

blades are also available at your nearest

Landxcape

TM

retailer.

A. Replace the Blades

After some time, usually every season, your Landxcape

TM

’s Blades

will need to be replaced. When replacing the blades, make sure to

replace ALL of them at the same time. You can replace them with one

of the spare blade kits and extra blade screws supplied with your

Landxcape

TM

.

Before attempting to replace your Landxcape

TM

’s blades, turn the

power off and put on protective gloves and follow these steps:

1. Gently flip Landxcape

TM

over.

2. Remove the battery cover and remove the battery.

3. Take the screws off the blades with a screwdriver. (See Fig. M)

4. Firmly screw on the new blades.

5. Refit the battery and the battery cover.

IMPORTANT: After screwing the blade to the blade disc, make

sure the blade is able to spin freely.

8.2 Keep it clean

WARNING:

Before cleaning, turn your Landxcape

TM

OFF.

Put on protective gloves before cleaning the blade

turning disc and do not rinse or flush with water.

A. Cleaning the body

Your Landxcape

TM

will live a much happier and longer life if it is

cleaned regularly. Although, since your Landxcape

TM

is an electric

machine, you will need to take care when cleaning.

DO NOT use a

hose, high pressure washers and do not pour running water on

your Landxcape

TM

.

It is best to use a spray bottle filled with water.

When cleaning the machine body, use a soft brush or clean cloth and

avoid using solvents or polishes (See Fig. N). Lastly, remove all build

up of grass clippings and debris.

B. Cleaning the Underside

Again, it is important that you power Landxcape

TM

OFF and

wear

EN 17

protective gloves before touching the blade turning disc

.

First, flip your Landxcape

TM

upside down to expose its underside. Here

you will see the blade disc, the chassis, and the front wheel and driving

wheels. Clean everything thoroughly with a soft brush or moist rag.

WARNING:

NEVER clean the underside of Landxcape

TM

with

running water. Component damage can occur. (See Fig. O1,

O2)

Rotate the blade disc to ensure it rotates freely. Check the blades spin

freely around the fixing screws. Remove any obstructions.

IMPORTANT:

Remove any lodged debris so that it does not cause

a crack in the blade disc. Even the tiniest crack can decrease

your Landxcape

TM

's mowing output.

C. Clean the contact pins and the charging strips

Clean the contact pins located on the charging base and the charging

strips located on Landxcape

TM

using a cloth. Remove any built up

grass clippings or debris around the contact pins and charge strips

periodically to ensure Landxcape

TM

successfully charges each time.

8.3 Battery life

The heart of Landxcape

TM

is its 20V Li-Ion battery. For proper storage of

the battery, make sure it is fully charged and kept in a cool dry place.

NOTE:

The recommended Landxcape

TM

operation temperature is

between 0-55

0

C.

The life-span of Landxcape

TM

’s battery depends on various factors,

such as:

• The length of the mowing season in your region

• Amount of hours Landxcape

TM

mows per day

• Battery maintenance during storage

Landxcape

TM

can be charged manually without the boundary

wire.

1. Connect the charging base to a suitable power supply. The

green light on the charging base will turn on.

2. Manually dock Landxcape

TM

into the charging base while

Landxcape

TM

is powered off. (See Fig. P)

3. The green light on the charging base will be flashing.

Landxcape

TM

will begin to charge.

8.4 Winter hibernation

Your Landxcape

TM

will live longer and healthier if it is allowed to

hibernate. So even though it is troublesome, we recommend storing

your Landxcape

TM

in your shed or garage during the winter.

Before you prepare your Landxcape

TM

for winter hibernation, we

recommend you:

• Thoroughly clean your Landxcape

TM

• Fully charge the battery and remove it from Landxcape

TM

• Turn power off

To maximize the battery life, fully charge the battery and remove it from

Landxcape

TM

before storage during winter.

WARNING: Protect the underside of Landxcape

TM

from

water. NEVER store Landxcape

TM

upside down outdoors.

The boundary wire can be left in the ground but its ends should be

protected, such as placed in a tin can with grease. If the charging base

is left outside for the winter, leave the boundary wire connected.

NOTE:

When bringing Landxcape

TM

back to work after winter

hibernation, make sure the charging strips and contact pins are clean.

We recommend using a fine grade emery cloth to clean the contacts.

8.5 Replacing the battery

WARNING: Power off before attempting any adjustment,

replacement or repair.

Before replacing the blades, turn your Landxcape

TM

OFF and put on

protective gloves.

If you need to replace the battery, follow these steps:

1. Gently turn your Landxcape

TM

upside down.

2. Remove the screws on the battery cover. Remove the battery cover.

(See Fig. Q1)

3. Lift out the old battery carefully. Press the latch and release the

connectors. (See Fig. Q2)

NOTE:

Do not pull by the cables. Hold the connectors and release the

latch.

4. Connect a new original battery by attaching the connectors until

they click into position. (See Fig. Q3, Q4)

5. Fit the battery as shown. (See Fig. Q5) Place the cover back in its

position and tighten the screws.

EN18

9. Function Messages

Display Message Action

Rain delay activated. No action is required.

10. Error Messages

Display Cause Action

Landxcape

TM

is outside

working area.

1. If

Landxcape

TM

is actually outside its territory: turn

Landxcape

TM

off, take

Landxcape

TM

inside its territory. Turn

Landxcape

TM

on. Press then .

2. If

Landxcape

TM

is inside its territory, check if the LED on the charging base is green. If not,

verify that the charging base is properly connected to the charger and that the charger is

connected to a suitable power supply. If they are properly connected, the boundary wires are

clamped incorrectly and must be reversed.

3. If the LED light on the charging base turns on red, confirm that the boundary wire is well

connected to the clamps on the charging base. If the problem persists, check that the boundary

wire hasn’t been cut.

Wheel motor blocked

1. Turn Landxcape

TM

off; take Landxcape

TM

to an area free of obstacles.

2. Turn Landxcape

TM

on. Press then .

3. If the error message is still displayed, turn power off; turn Landxcape

TM

upside-down and

check if there’s anything preventing the wheels from rotating.

4. Remove any obstruction, turn Landxcape

TM

upright, turn power on. Press then .

Blade disc blocked

1. Turn Landxcape

TM

off.

2. Turn Landxcape

TM

upside down and check if there’s anything preventing the blade disc to

rotate.

3. Remove any obstruction.

4. Turn Landxcape

TM

upright and take it to an area with short grass or adjust the cutting

height;

5. Turn Landxcape

TM

on. Press then .

Landxcape

TM

is trapped.

1. Turn Landxcape

TM

off;

2. Take Landxcape

TM

to an area in your lawn free of obstacles obstacles.

3. Turn Landxcape

TM

on. Press

then .

4. If the error message is still displayed; turn power off; turn Landxcape

TM

upside-down.

Check if there is anything preventing the wheels from rotating.

5. Remove any obstruction, turn Landxcape

TM

upright, turn power on. Press

then .

Landxcape

TM

is lifted up.

1. Turn Landxcape

TM

off.

2. Take Landxcape

TM

to a lawn area clear of obstacles, turn Landxcape

TM

on. Press

then .

3. If the error message is still displayed: turn Landxcape

TM

off, turn Landxcape

TM

upside-

down and check if there’s anything preventing the front wheels from rotating.

4. Remove any possible object, turn Landxcape

TM

upright, turn Landxcape

TM

on. Press

then .

Landxcape

TM

is upside

down.

Turn Landxcape

TM

upright. Press then .

Battery error

1. Check the battery temperature. If the temperature is too high, wait until the

temperature has cooled down. Press then .

2. If the error message is still displayed, replace a new battery. Restart Landxcape

TM

.

Press then .

3. If the error repeatedly occurs, try to change the working schedule.

EN 19

It takes too long for

Landxcape

TM

to go back to

the charging base.

Manually dock Landxcape

TM

in the charging base for charging. After Landxcape

TM

is

fully charged, Press then .

Error unknown.

Restart Landxcape

TM

. Press then . If the error message is still displayed,

contact a service agent for help.

NOTES

• Before turning power on, always return Landxcape

TM

to its territory. If not, “

” will be displayed. This message is also displayed when

Landxcape

TM

is sitting over the boundary wire when turned on.

• If for any reason—i.e. a party, children playing...—you want to park your Landxcape

TM

in the charging base: Press then . Landxcape

TM

will go to its charging base and stay there. Press to turn Landxcape

TM

off.

• If an error repeatedly occurs in the same area of your lawn, you might have a problem with the boundary wire. Please refer to the Installation

Guide and check your set up with its help.

• If your lawn is divided in two separate areas connected by a corridor less than 1m, one of which is not provided with the charging base: when

Landxcape

TM

runs out of charge, take it manually to the charging base, the charge process will start.

• If Landxcape

TM

runs abnormally once in a while, please try to restart it. If the problem is not resolved, try to removing and reinstalling the

battery . If the problem is still not resolved, please contact a Landxcape

TM

service agent for help.

• Do not wash your Landxcape

TM

with a high pressure washer. This could cause damage to the battery or the machine.

11. Troubleshooting

If your Landxcape

TM

does not work correctly, follow the troubleshooting guide below. If the issue persists, contact your Dealer.

Symptom Cause Action

The LED light on the charging base does

not turn on.

There is no power.

Check the charging base is connected properly to the

charger and the charger is connected to a suitable

power supply.

Red light turns on the charging base. The boundary wire isn’t connected.

Check that the boundary wire has been connected

correctly to the charging base.

Check there are no breaks in the boundary wire, especially

in the wire ends.

Landxcape

TM

turns on, but the blade

disc does not move.

Landxcape

TM

is searching for the charging

base (unless you press then button to

make it go to the charging base)

This is normal. Landxcape

TM

needs to recharge, the

blade disc does not rotate while it is searching for the

charging base automatically.

Landxcape

TM

vibrates.

Blades may be damaged. Check condition of

the blade disc.

Check the blades, and replace them if damaged.

Remove debris and foreign objects from the blades

and blade disc.

Grass is being cut unevenly.

Landxcape

TM

does not work enough hours per

day.

Add more hours to the scheduled mowing time.

Mowing area is too big.

Try decreasing the size of the mowing area or adding

more hours to the mowing time.

Blades are dull.

Change all the blades and screws in order to balance

the blade disc.

The cutting height is too low for the length of

the grass.

Raise the cutting height and then gradually lower.

Grass or other object has wrapped around the

blade disc.

Check the blade disc and remove the grass or other

object.

There is a build-up of grass in the blade disc or

motor frame box.

Make sure the blade disc rotates easily. If need be, you

may take off the blade disc and remove the debris.

Your Landxcape

TM

is inside its territory

and the boundary wire is connected.

And “

“ is displayed.

The boundary wire ends are clamped

incorrectly.

Reverse the boundary wire ends.

The boundary wire is broken. Repair damaged boundary wire with connectors.

EN20

The charging time is far more than the

rated charging time.

Poor connection caused by debris on the

charging strip.

Clean the contact pins located on the charging base

and the charging strip on Landxcape

TM

using a cloth.

The charging protection program has activated

due to high temperature.

Place the charging base in a shady area or wait until

the temperature has cooled down.

The mower does not charge.

There is no power.

Check the power cord is connected properly to the

charger and the charger is connected to a suitable

power supply.

Landxcape

TM

does not operate correctly while

manually charging.

Refer to manual charging in Section 8.3.

Landxcape

TM

is starting to have shorter

run-times between charges.

Something is clogging in the blade disc. Take off the blade disc and clean it.

The grass is too high and too thick.

Check the Blade Disc and blades, remove debris and

foreign objects from the blades and Blade Disc.

Landxcape

TM

is shaking heavily.

Check the blade disc and blades, remove debris and

foreign objects from the blades and blade disc.

Landxcape

TM

is not operating at the

correct time.

The clock is not set to the correct time.

Set the clock to the correct time (refer to Section 5.3)

or by using App.

Programmed cutting times for Landxcape

TM

are not correct.

Change the time settings for the mower to start and

stop.

Landxcape

TM

is manually docked in the

charging base.

Press

then .

The battery does not charge as its temperature

rises above 55

O

C in hot weather.

Wait until the battery has cooled down.

Landxcape

TM

cannot correctly dock

with the charging base.

Environmental influences. Restart Landxcape

TM

.

Poor connection caused by debris on the

charging strip.

Clean the contact pins located on the charging base

and the charging strip on Landxcape

TM

using a cloth.

The green light on the charging base

turns on before charging is complete.

The charging base is overheated.

Place the charging base in a shady area or wait until

the temperature has cooled down.

Landxcape

TM

runs outside the boundary

wire. Landxcape

TM

does not mow an

area within a boundary wire zone.

Landxcape

TM

reverses or rotates

erratically near the boundary wire.

The boundary wire of another Landxcape

TM

or another robotic mower is positioned too

closely.

Ensure your Landxcape

TM

boundary wire has at least

1m of space between the neighboring boundary wire.

The boundary wire has been installed with

tight corners.

Check the boundary wire to ensure the corners are

smooth.

In wet conditions, the boundary wire electric

signal may leak were wire has been joined or

repaired.

Check boundary wire joints. Insulate to provide a fully

waterproof connection.

There is boundary wire electric signal leakage

due to broken insulation.

Repair damaged boundary wire insulation with

connectors.

The cutting area is larger than the allowable

cutting area for Landxcape

TM

.

Reduce the cutting area or use Landxcape

TM

with a

larger allowable cutting area.

Landxcape

TM

wheels skid or damage

lawn.

Foreign obstacles, such as twigs and branches

may be lodged under Landxcape

TM

.

Remove foreign objects from underside of

Landxcape

TM

.

The lawn is too wet. Wait until lawn has dried.

Landxcape

TM

exits the boundary wire

due to high speed when going down a

hill.

The boundary wire is placed on a slope

steeper than 17% (10°).

Reposition the boundary wire away from slopes that

are steeper than 17% (10°). Please refer Installation

Guide for details.

Software update failure occurs. Try again according to section “Software update”.

Environmental Protection

Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local

Authority or retailer for recycling advice.

La page charge ...

Landxcape LX793 Le manuel du propriétaire

Ce manuel convient également à

Landxcape LX793 Le manuel du propriétaire

dans d''autres langues

Autres documents