Modern Forms FR-W2006-62L-MW Guide d'installation

Installation Instructions

Zephyr

works with the

Google Assistant

FR-W2006Zephyr Instructions2

Please read and

save these instructions

before installation

DO NOT RETURN TO STORE

FR-W2006

Zephyr Instructions 3

For all questions about your ceiling fan please read all included

instructions, installation procedures, troubleshooting guidelines

and warranty information before starting installation.

For missing parts or general inquiries call our trained technical sta at:

1-866-810-6615 option 0

MON-FRI 8AM-8PM EST

Email: customerservice@modernforms.com

Or live chat at modernforms.com

For fast service have the following information below when you call:

1. Model Name and Number

2. Part Number and Part Description

3. Date Of Purchase and Purchase Location

1-866-810-6615 option 1

MON-FRI 8AM-8PM EST

Email: fansupport@modernforms.com

General Inquiries

Fan Support

FR-W2006Zephyr Instructions4

For operation, maintenance, and troubleshooting information,

visit http://modernforms.com/fan-support/

To reduce the risk of electric shock, ensure electricity has been turned o at the circuit breaker

before beginning. All wiring must be in accordance with the National Electrical Code “ANSI/NFPA

70” and local electrical codes. Electrical installation should be performed by a licensed electrician.

The fan must be mounted with a minimum of 7 ft. (2.1m) clearance from the trailing edge of

the fan blades to the oor and a minimum of 1.5 ft (0.5m) from the edge of the fan blades to the

surrounding walls. Never place objects in the path of the fan blades. To avoid personal injury or

damage to the fan and other items, please be cautious when working around or cleaning the fan.

To avoid electrical shock or damage to the motor or nish, do not use water or chemicals

when cleaning the fan or fan blades. A dry cloth or lightly dampened cloth will be suitable

for most cleaning.

After making electrical connections, spliced conductors should be turned upward and pushed

carefully up into the outlet box. The wires should be spread apart with the grounded conductor and

the equipment-grounding conductor on one side of the outlet box, and the ungrounded conductor

on the other side of the outlet box.

All set screws must be checked and re-tightened

where necessary before installation.

Safety Rules

FR-W2006

Zephyr Instructions 5

WARNING: Do not install or use your fan if any part(s) is/are damaged or missing. This product

is designed for use only with the supplied parts and/or accessories designated for use with this

product by Modern Forms. Substitution of parts or accessories not designated for use with this

product by Modern Forms could result in personal injury or property damage and will void the

warranty. Contact an authorized dealer or the manufacturer if any parts are damaged or missing.

WARNING: To reduce the risk of electric shock, this fan must

be installed and operated with the supplied wall control, or controlled from the Modern Forms app

or Wi-Fi Touch Panel Wall Control (not included).

WARNING: Do not use power tools to assemble or install your fan. Using power tools can result in

improper assembly which can lead to noise or fan damage,personal injury or property damage.

WARNING: To reduce the risk of personal injury, do not bend the blade arms when installing the

brackets, balancing the blades or cleaning the fan.

WARNING: Do not insert foreign objects between rotating fan blades.

WARNING: Do not operate fan unless fan blades are in place. Noise and fan damage can occur

WARNING: This appliance is not intended for use by young children without supervision.

WARNING: To reduce the risk of re, electric shock, personal injury or damage to the fan or other

items, the outlet box and support structure must be securely mounted and capable of reliably

supporting a minimum of 35 Ibs (15.9 kg). Use only UL/cUL listed outlet boxes marked “FOR FAN

SUPPORT.” Use only the screws and washers provided with the outlet box.

CAUTION: Before assembling your fan, refer to the “Making the Electrical Connections“

section. If you feel you do not have enough wiring knowledge or experience, have your fan

installed by a licensed electrician.

NOTE: Before servicing or cleaning the fan, switch power o at the circuit breaker.

FR-W2006Zephyr Instructions6

Integrates

seamlessly with:

devices you already own

works with the

Google Assistant

Get Smart...

Premium smart

features:

Accessories:

DC

MOTOR

complement high quality materials

personalize your experience

Quiet, reliable, and up to 70%

more ecient than AC fans

Wi-Fi and Bluetooth enabled

for exible control

Bluetooth Wall Control

Dims light to 1% | ON/OFF

6 fan speeds | Sold separately

F-WCBT-WT White

Bluetooth Remote Control

Dims light to 1% | ON/OFF

6 fan speeds

F-RCBT-WT White

Wet Location-listed to the strictest

UL/cUL safety regulations. Finished

and rated for interior and exterior use

FR-W2006

Zephyr Instructions 7

1. Mounting Options 10

2. Installing the Mounting Bracket 12

3. Attaching the Fan Blades 12

4. Installing the Adapter Plate 14

5. Hanging the Fan 14

6. Making the Electrical Connections 18

7. Installing the Optional Wall Control 20

8. Finishing the Installation 22

9. Installing the LED Luminaire Module 24

10. Controlling the Fan 26

11. Reset 28

12. Breeze Mode 28

13. Application 28

14. Accessories 30

14. Troubleshooting 32-34

Contents

Tools Required

FR-W2006Zephyr Instructions8

7. Motor Assembly

8. Blade Collector Ring

9. LED Module

F4IN-120V-R1-30

10. Control Receiver

w/Hardware

F-R3-2006-**

11. Glass Shade

RPL-F2006-GLA

12. Luminaire Cover

RPL-F2006-COVER-**

• 1/4” x13mm+S Phil/Slotted

Screws With washer (7)

• #8x10mm Phillips Truss

head Screws (7)

• #10x38mm Pan Head

Phillip Screws (2)

• Ø5*14*1mm Flat Washer (2)

• 3/16” Star Washer (2)

• Ø6.5x19x2mm Flat Washer (1)

• 3/16”(Ø5.2x8.4x1.0mm)

Spring Washer (1)

• #10x76mm Pan Head

Phillip Wood Screws (1)

1. Blade Set of 3

RPL-F2006-**-BD-**

2. Hanger Assembly

Mounting Bracket

Downrod Assembly

RPL-HGR-ASM-**

3. Downrod 4.5 inch

(optional for closer to

ceiling mount applications)

4. Canopy w/Canopy Ring

RPL-CAN-OCT-**

5. Coupling Cover

6. Adapter Plate

Package Contents

Before discarding packaging materials be certain all parts have been removed.

Place the parts from the hardware bag into a small container to keep them from being lost.

Hardware Bag

RPL-F2006-PARTS

** denotes nish code of fan *** denotes blade sweep of fan

FR-W2006

Zephyr Instructions 9

12

1

8

7

10

11

9

4

5

6

Hanging Weight: 17 lbs

IMPORTANT: Please make note of

the MAC ID on the receiver and

keep it in a safe place.

MAC ID

2

3

FR-W2006Zephyr Instructions10

1. Mounting Options

CAUTION: To prevent electrical shock, ensure electricity has been

turned o at the circuit breaker before beginning.

If there isn’t an existing UL/cUL listed outlet box, please refer to the

following instructions. Secure the outlet box directly to the building

structure. Use appropriate fasteners and building materials. The

outlet box and support structure must be able to fully support the

moving weight of the fan (at least 35 lbs/15.9 kg). Do not use plastic

outlet boxes. Use only UL/cUL listed outlet boxes marked

“FOR FAN SUPPORT.”

Secure the outlet box directly to the building structure.

Figures 1-1C are examples of dierent ways to mount the

outlet box.

NOTE: To hang your fan where there is an existing xture but no

ceiling joist, you may need an installation hanger bar.

NOTE: Downrod fans can be suspended up to a maximum

recommended length of 72” using additional downrods

(sold separately) and the included 80” lead wire.

NOTE: The sloped ceiling kit (sold separately) is required for sloped

ceiling applications, and will accommodate slopes up to 45° (Fig. 1B).

NOTE: You may need a longer downrod to maintain proper blade

clearance when installing on a steep, sloped ceiling (Fig. 1B).

FR-W2006

Zephyr Instructions 11

1

1A

1B

1C

1

2

1

2

3

1. Support Brace

2. Outlet Box

3. Joist

1. Support Brace

2. Mounting Bracket

3. Recess Outlet Box

1. Outlet Box

Support Ceiling

Max 30° Angle

FR-W2006Zephyr Instructions12

Remember to turn o power at the breaker.

Follow the steps below to hang your fan properly:

1. Disconnect power at the breaker to the fan location.

2. Remove 1 of 2 screws from the bottom of mounting bracket and

save for use in Finishing the Installation section. Loosen the other

screw (Fig. 2).

3. Pass the 120-volt supply wires through the center hole in the

ceiling mounting bracket as shown in (Fig. 2A).

4. Secure the mounting bracket to the ceiling outlet box with the

screws and washers provided with your outlet box (Fig. 2A).

2. Installing the Mounting Bracket

3. Attaching the Fan Blades

1. Remove and discard the 2 pre-installed screws on the motor

as shown (Fig. 3).

2. Attach the fan blades with the blade screws provided (Fig. 3).

3. Turn the fan motor assembly over and install the blade collector

ring with the screws provided (Fig. 3A).

5

FR-W2006

Zephyr Instructions 13

3

2 2A

3A

1

2

1

3

4

1. 120V Wires

2. cUL Listed Electrical Box

3. Mounting Bracket

4. Mounting Screws

(supplied with outlet box)

1. Mounting Bracket

2. Screw

FR-W2006Zephyr Instructions14

5. Hanging the Fan

4. Installing the Adapter Plate

1. Remove one of the three mounting plate screws from the

mounting ring and loosen the other two screws

(Do not remove) (Fig. 4).

2. Place the key holes in the adapter plate over the two screws

previously loosened from the mounting ring. Turn the light

kit plate until it locks in place at the narrow section of the

key holes (Fig. 4A).

3. Securely tighten the two adapter plate screws previously

removed.

1. Take out the set screw located in the hanger ball, lower the

hanger ball and remove the cross pin. Remove the hanger ball from

the hanger ball/8 inch downrod assembly (Fig. 5). If you prefer

the fan also comes included with an optional 4.5 inch downrod for

closer to ceiling mount applications.

2. Remove the clevis pin and cotter pin, and loosen the two collar

screws from the motor collar (Fig. 5).

3. Carefully feed the motor wires and safety cable up through the

downrod. Thread the downrod into the collar.

4. Align the holes of downrod and collar and insert the cotter pin and

clevis pin. Tighten the two collar screws (Fig. 5).

WARNING: Failure to properly install the cotter pin and/or tighten

the screws could result in the fan loosening and possibly falling.

FR-W2006

Zephyr Instructions 15

4 4A

5

2

1

3

9

8

7

5

6

4

1. Hanger Ball/Mounting Bracket

2. Downrod

3. Canopy

4. Canopy Screw Cover

5. Coupling Cover

6. Collar

7. Cotter Pin

8. Clevis Pin

9. Screws

FR-W2006Zephyr Instructions16

1. Slip the coupling cover, canopy screw cover (painted side face

down), and canopy (opened side up) onto the downrod (Fig. 5A).

Coupling cover goes all the way to the bottom.

2. Carefully reinstall the hanger ball onto the downrod, being sure

that the cross pin is in the correct position, the setscrew is

tightened and wires are not twisted (Fig. 5A).

3. Carefully lift the fan motor assembly up to the mounting

bracket and seat the hanger ball in the mounting bracket socket.

Make sure the tab on the mounting bracket socket is properly

seated in the groove in the hanger ball (Fig. 5A). Rotate the

socket assembly until the ball drops and locks into the hanger

bracket screw.

4. Secure the safety cable into the structure beams using the wood

screw, washers, and spring washers provided (Fig. 5B).

NOTE: A Safety cable is required for all installations in Canada.

Safety cable is required for ceiling fan and light combinations over

35 lbs. in both ush and downrod models in the United States.

5. Hanging the Fan

FR-W2006

Zephyr Instructions 17

5A

5B

FR-W2006Zephyr Instructions18

6. Making the Electrical Connections

WARNING: Installation of this fan requires that a three-conductor

cable (including ground wire) which should run between ceiling and

wall outlet box.

WARNING: Check to see that all connections are tight, including

ground, and that no bare wire is visible at the wire nuts,

except for the ground wire.

Insert the receiver into the mounting bracket with the at side of the

receiver facing the ceiling (Fig. 6).

Motor to Receiver & Receiver to house supply wires (Fig. 6A).

1. Connect the hanger ball/downrod assembly ground wire,

mounting bracket ground wire and receiver ground wire to

the ground wire in outlet box.

WARNING: Failure to connect ground wires could result in

poor fan control functionality.

2. Connect the red wire from the fan to the red wire marked

“TO MOTOR” from the receiver.

3. Connect the grey wire from the fan to the grey wire marked

“TO MOTOR” from the receiver.

4. Connect the yellow wire from the fan to the yellow wire marked

“TO MOTOR” from the receiver.

5. Connect the white wire from the fan to the white wire marked

“FOR LIGHT” from the receiver.

6. Connect the black wire from the fan to the blue wire marked

“FOR LIGHT” from the receiver.

7. Connect the black (hot) wire from the ceiling to the black wire

marked “AC in L” from the receiver.

8. Connect the white (neutral) wire from the ceiling to the white

wire marked “AC in N” from the receiver.

FR-W2006

Zephyr Instructions 19

Follow the steps above to connect the fan to your household wiring. Use the plastic wire nuts with your fan.

Secure the plastic wire nuts with electrical tape. Make sure there are no loose strands or connections.

6

6A

1

2

1. Mounting Bracket

2. Receiver

Black(Hot)

can be RED from Switch leg

Black(Line in H)

RED(to Motor)

GREEN(Ground)

BLUE (to Light)

BLACK (for Light)

GREEN(GND Must Use)

GREEN(Hanger Bracket Ground)

RED(to Motor)

GREY(to Motor)

WHITE(Neutral)

WHITE(to Light)

WHITE(Neutral)

Safety Cable

GREY(to Motor)

YELLOW(to Motor)

WHITE(Line in N)

YELLOW(to Motor)

Outlet

Box

Receiver

Hanger Ball & Downrod

Hanger

Bracket

FR-W2006Zephyr Instructions20

7. Installing the Optional Wall Control

NOTE: Bluetooth Wall Control Optional Accessory not included.

A Bluetooth Wall Control can be purchased separately.

1. Connect the green wire marked “GROUND” from the wall

control to the copper wire from the wall outlet box that

feeds back to the circuit breaker – important for proper

fan function (Fig. 7).

2. Connect the black wire marked “LINE IN” from the wall control to

the black LINE VOLTAGE wire from the wall outlet box that feeds

back to the circuit breaker (Fig. 7).

3. Connect the red wire from the wall control to the black wire from

the wall outlet box that feeds up to the fan (Fig. 7).

4. Connect the white wire from the wall control to the white

(neutral) wire from the wall outlet box (Fig. 7).

5. Carefully tuck the wire connections inside the outlet box.

Secure the wall control with the two (2) wall control screws

provided (Fig. 7A).

6. Attach the wall mounting plate over the wall switch and secure

with the two (2) wall mounting plate screws provided (Fig. 7A).

7. Fasten the wall plate to the wall mounting plate (Fig. 7A).

7

Wall Switch WiresHouse Wires

(Hot In)

(Neutral)

(Ground)

(Hot out to Fan)Fan Switch leg

(Copper/Ground)

(Neutral)

(Hot)

From Breaker

* Home Wiring may vary

to Fan

La page charge ...

Modern Forms FR-W2006-62L-MW Guide d'installation

Ce manuel convient également à

Modern Forms FR-W2006-62L-MW Guide d'installation

dans d''autres langues

Documents connexes

Autres documents