Ryobi TBBC Manuel utilisateur

Marque: Ryobi

Modèle: TBBC

Taper: Manuel utilisateur

Ce manuel convient également à

Brush Cutter TBBC

Operator’s Manual

Brushcutter

TBBC

IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY

P/N 769-02046A (5/06)

Never use this attachment with an electric-powered unit. Only

attach the TBBC to gas-powered trimmers or brushcutters.

Use with an electric product could lead to damage to the unit or serious personal injury.

WARNING:

INTRODUCTION

Copy the serial number

here:

THANK YOU

Thank you for buying this quality product. This modern

outdoor power tool will provide many hours of useful

service. You will find it to be a great labor-saving device.

This operator’s manual provides you with easy-to-

understand operating instructions. Read the whole

manual and follow all the instructions to keep your new

outdoor power tool in top operating condition.

PRODUCT REFERENCES, ILLUSTRATIONS

AND SPECIFICATIONS

All information, illustrations, and specifications in this

manual are based on the latest product information

available at the time of printing. We reserve the right to

make changes at any time without notice.

Reserved.

SERVICE INFORMATION

For service call 1-800-520-5520 in the United States, or

1-800-668-1238 in Canada to obtain a list of authorized

service dealers near you. For more details about your

unit, visit our website at www.troybilt.com.

DO NOT RETURN THE UNIT TO THE RETAILER.

PROOF OF PURCHASE WILL BE REQUIRED FOR

WARRANTY SERVICE.

THIS PRODUCT IS COVERED BY ONE OR MORE U.S.

PATENTS. OTHER PATENTS PENDING.

Service on this unit both within and after the warranty

period should be performed only by an authorized and

approved service dealer.

S/N :

ITEM :

MODEL :

TABLE OF CONTENTS

Service Information . . . . . . . . . . . . . . . . . . . . . . . . .2

Rules for Safe Operation . . . . . . . . . . . . . . . . . . . . .3

Know Your Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Assembly Instructions . . . . . . . . . . . . . . . . . . . . . . .8

Operating Instructions . . . . . . . . . . . . . . . . . . . . . .10

Maintenance and Repair Instructions . . . . . . . . . . .13

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Warranty Information . . . . . . . . . . . . . . . . . . . . . . .16

Parts List . . . . . . . . . . . . . . . . . . . .Inside Back Cover

Copy the model and parent

part number here:

Before beginning, locate the unit’s model plate. It lists

the model and serial numbers of your unit. Refer to the

sample plate below and copy the information for future

reference.

RULES FOR SAFE OPERATION

SYMBOL MEANING

The purpose of safety symbols is to attract your

attention to possible dangers. The safety symbols,

and their explanations, deserve your careful attention

and understanding. The safety warnings do not by

themselves eliminate any danger. The instructions or

warnings they give are not substitutes for proper

accident prevention measures.

NOTE: Advises you of information or instructions vital to

the operation or maintenance of the equipment.

SYMBOL MEANING

• IMPORTANT SAFETY INSTRUCTIONS •

Failure to obey a

safety warning can

result in injury to yourself and others.

Always follow the safety precautions to

reduce the risk of fire, electric shock and

personal injury.

WARNING:

Failure to obey a

safety warning will

result in serious injury to yourself or to

others. Always follow the safety precautions

to reduce the risk of fire, electric shock and

personal injury.

DANGER:

Failure to obey a

safety warning may

result in property damage or personal injury

to yourself or to others. Always follow the

safety precautions to reduce the risk of fire,

electric shock and personal injury.

CAUTION:

Indicates

danger,

warning or caution. Attention is required in

order to avoid serious personal injury. May

be used in conjunction with other symbols

or pictographs.

SAFETY ALERT:

Read the Operator’s Manual(s) and follow all

warnings and safety instructions.

Failure to do so can result in serious injury to the

operator and/or bystanders.

FOR QUESTIONS, CALL 1-800-520-5520

READ ALL INSTRUCTIONS

BEFORE OPERATING

• Read the instructions carefully. Be familiar with the

controls and proper use of the unit.

• Do not operate this unit when tired, ill, or under the

influence of alcohol, drugs, or medication.

• Children and teens under the age of 15 must not use

the unit, except for teens guided by an adult.

• All guards and safety attachments must be installed

properly before operating the unit.

• Inspect the unit before use. Replace damaged parts.

Check for fuel leaks. Make sure all fasteners are in

place and secure. Replace parts that are cracked,

chipped, or damaged in any way. Do not operate the

unit with loose or damaged parts.

When using the unit,

you must follow the

safety rules. Please read these instructions

before operating the unit in order to ensure

the safety of the operator and any bystanders.

Please keep these instructions for later use.

WARNING:

• Be aware of the risk of injury to the head, hands and feet.

• Carefully inspect the area before starting the unit.

Remove all debris and hard or sharp objects such as

glass, wire, etc.

• Clear the area of children, bystanders, and pets. At a

minimum, keep all children, bystanders, and pets

outside a 50 feet (15 m.) radius; there still may be a

risk to bystanders from thrown objects. Bystanders

should be encouraged to wear eye protection. If you

are approached, stop the unit immediately.

• Only for use on attachment-capable, gas-powered

trimmers that have the On/Off Stop control located on

the grip.

Never use this attachment with an electric-powered unit. Only

attach the TBBC to gas-powered trimmers or brushcutters.

Use with an electric product could lead to damage to the unit or serious personal injury.

WARNING:

On/Off Stop

Control

(located on grip)

RULES FOR SAFE OPERATION

SAFETY WARNINGS FOR GAS

POWERHEADS

• Store fuel only in containers specifically designed and

approved for the storage of such materials.

• Always stop the engine and allow it to cool before

filling the fuel tank. Never remove the cap of the fuel tank,

or add fuel, when the engine is hot. Never operate the

unit without the fuel cap securely in place. Loosen the

fuel tank cap slowly to relieve any pressure in the tank.

• Add fuel in a clean, well-ventilated outdoor area where

there are no sparks or flames. Slowly remove the fuel

cap only after stopping engine. Do not smoke while

fueling or mixing fuel. Wipe up any spilled fuel from the

unit immediately.

• Avoid creating a source of ignition for spilled fuel. Do

not start the engine until fuel vapors dissipate.

• Move the unit at least 30 feet (9.1 m) from the fueling

source and site before starting the engine. Do not

smoke. Keep sparks and open flames away from the

area while adding fuel or operating the unit.

• Squeeze the throttle control and check that it returns

automatically to the idle position. Make all adjustments

or repairs before using the unit.

WHILE OPERATING

• Read and understand all safety warnings before

operating this unit.

• Inspect thoroughly for loose nuts, bolts or damage

before continuing. Repair or replace affected parts as

necessary.

• Wear safety glasses or goggles that meet ANSI Z87.1

standards and are marked as such. Wear ear/hearing

protection when operating this unit. Wear a face or

dust mask if the operation is dusty.

• Wear heavy long pants, boots, gloves and a long

sleeve shirt. Do not wear loose clothing, jewelry, short

pants, sandals or go barefoot. Secure hair above

shoulder level.

• Adjust the J-handle to your size in order to provide the

best grip.

• Use the unit only in daylight or good artificial light.

• Avoid accidental starting. Be in the starting position

whenever pulling the starter rope. The operator and

unit must be in a stable position while starting. Refer

to Starting/Stopping Instructions of the power head

manual.

• Use the right tool. Only use this tool for its intended

purpose.

• Do not overreach. Always keep proper footing and

balance.

• Always hold the unit with both hands when operating.

Keep a firm grip on both handles or grips.

• Keep hands, face, and feet at a distance from all

moving parts.

• Do not operate the engine/motor faster than the speed

needed to cut. Do not run the engine at high speed

when not cutting.

• Always stop the engine when you delay working, or

when you walk from one cutting location to another.

• If you strike or become entangled with a foreign

object, stop the engine immediately and check for

damage. Do not operate before repairing damage. Do

not operate the unit with loose or damaged parts.

Gasoline is highly

flammable, and its

vapors can explode if ignited. Take the

following precautions:

WARNING:

• The TBBC is specifically approved for use with the

following models of attachment-capable trimmers:

Ryobi: Troy-Bilt:

775R TB20CS

750R TB25CS

790R TB25ET

890R TB70SS

TB75SS

Yard Man:

TB90BC

YM25 TB425CS

YM75 TB475SS

YM90 TB490BC

YM26BC

Bolens (Canada):

Cub Cadet:

BL26BC

CC2025

CC3075

Yardworks:

CC4025 60-2310-6

CC4075 60-2311-4

CC4090 60-2312-2

• Do not touch the engine, gear housing or muffler.

These parts get extremely hot from operation, even

after the unit is turned off.

• To reduce fire hazard, replace a faulty muffler and

spark arrestor. Keep the engine and muffler free from

grass, leaves, excessive grease or carbon build up.

• Never start or run the unit inside a closed room or

building. Breathing exhaust fumes can be fatal.

Operate this unit only in a well-ventilated outdoor area.

• Do not sharpen the cutting blade. Sharpening the blade

can cause the blade tip to break off while in use. This

can result in severe personal injury. Replace the blade.

• Do not use the cutting blade for edging or as an edger;

severe personal injury to yourself or others may incur.

Use the cutting blade only for the purpose described

in this manual.

• Stop the engine IMMEDIATELY if you feel excessive

vibration. Vibration is a sign of trouble. Inspect

thoroughly for loose nuts, bolts or damage before

continuing. Repair or replace affected parts as

necessary.

After Use

• Clean cutting blades with a household cleaner to

remove any gum buildup. Oil the blade with machine

oil to prevent rust.

• Lock up and store the cutting blade in an appropriate

area to protect the blade from unauthorized use or

damage.

OTHER SAFETY WARNINGS

• Never store a fueled unit inside a building where fumes

may reach an open flame or spark.

• Allow the engine to cool before storing or transporting.

Be sure to secure the unit while transporting.

• Store the unit in a dry area, locked up or up high to

prevent unauthorized use or damage, out of the reach

of children.

• Never douse or squirt the unit with water or any other

liquid. Keep handles dry, clean and free from debris.

Clean after each use, see Cleaning and Storage

instructions.

• Keep these instructions. Refer to them often and use

them to instruct other users. If you loan someone this

unit, also loan them these instructions.

SAVE THESE

INSTRUCTIONS

• Stop the unit, switch the engine to off, and disconnect

the spark plug for maintenance or repair.

• Use only original equipment manufacturer replacement

parts and accessories for this unit. These are available

from your authorized service dealer. Use of any

unauthorized parts or accessories could lead to

serious injury to the user, or damage to the unit, and

void your warranty.

• Keep unit clean of vegetation and other materials.

• Always use the shoulder harness when using the

brush blade attachment.

• Keep the J-handle between the operator and blade at

all times.

• NEVER cut when the cutting blade is 30 inches

(76 cm) or more above the ground level.

• Blade thrust may occur when the spinning blade

contacts an object that it does not immediately cut.

Blade thrust can be violent enough to propel the unit

and/or operator in any direction, possibly causing a

loss of control. Blade thrust can occur without warning

if the blade snags, stalls or binds. This is more likely to

occur in areas where it is difficult to see the material

being cut.

• For operation with the brush blade, do not cut

anything thicker than 1/2 inch or a violent kickback

could occur.

• Do not attempt to touch or stop the blade when it is

rotating.

• A coasting blade can cause injury while it continues to

spin after the engine is stopped or the throttle trigger

is released. Maintain proper control until the blade has

completely stopped rotating.

• Do not run the unit at high speed when not cutting.

• If you strike or become entangled with a foreign

object, stop the engine immediately and check for

damage. Have any damage repaired before attempting

further operations. Do not operate unit with a bent,

cracked or dull blade. Discard blades that are bent,

warped, cracked or broken.

RULES FOR SAFE OPERATION

SYMBOL MEANING

• THROWN OBJECTS AND

ROTATING CUTTER CAN

CAUSE SEVERE INJURY

WARNING: Do not

operate without the cutting

attachment shield in place.

Keep away from the rotating cutting

attachment.

• BRUSHCUTTERS •REPLACE

DULL BLADE

Do not sharpen the cutting blade.

Sharpening the blade can cause the

blade tip to break off while in use. This

can result in severe personal injury.

• TRIMMER/ BRUSHCUTTER

SAFETY

WARNING: Thrown

objects and rotating cutter can

cause severe injury. Keep

bystanders, especially children and

pets, at least 50 feet (15 m) away

from the cutting area. The cutting

attachment shield must be used

when using the trimmer cutting

attachment.

SYMBOL MEANING

• SAFETY ALERT SYMBOL

Indicates danger, warning or

caution. May be used in conjunction

with other symbols or pictographs.

• WARNING - READ

OPERATOR'S MANUAL

Read the operator’s manual(s) and

follow all warnings and safety

instructions. Failure to do so can result

in serious injury to the operator and/or

bystanders.

• WEAR EYE AND HEARING

PROTECTION

WARNING: Thrown

objects and loud noise can cause

severe eye injury and hearing loss.

Wear eye protection meeting ANSI

Z87.1 standards and ear protection

when operating this unit. Use a full

face shield when needed.

•KEEP BYSTANDERS AWAY

WARNING: Keep all

bystanders, especially children and

pets, at least 50 feet (15 m) from the

operating area.

SAFETY AND INTERNATIONAL SYMBOLS

This operator's manual describes safety and international symbols and pictographs that may appear on this product.

Read the operator's manual for complete safety, assembly, operating and maintenance and repair information.

RULES FOR SAFE OPERATION

APPLICATIONS

• Cutting weeds and light brush of up to 1/2 inch

in diameter

KNOW YOUR UNIT

Gear Housing

Shaft

Housing

Blade Shield

Brush

Blade

Hanger

Shoulder Harness

Locking Rod

Shoulder

Harness Loop

24” J-Handle

J-Handle Clamp Assembly

with Hardware

(4) Screws

Top Clamp

J-Handle

Middle Clamp

Bottom Clamp

Nuts

ASSEMBLY INSTRUCTIONS

INSTALL AND ADJUST THE 24” J-HANDLE

Installing

1. Remove the screws, nuts, clamp pieces that were

installed on the J-handle for shipping.

2. Hold the bottom clamp to the underside of the shaft

housing, about 7-8” from the shaft grip (Fig. 1).

3. Place the J-handle between the top and middle

clamp pieces (Fig. 1).

4. While holding the three pieces together, install the

four (4) screws through the top clamp and into

middle clamp.

NOTE: The holes in the top and middle clamp will line

up only when assembled correctly.

5. Place the clamps and J-handle the over the shaft

housing and onto the bottom clamp.

6. Hold each hex nut in the bottom clamp recess with a

finger. Start screws with a large Phillips screwdriver.

Do not tighten until you make the handle adjustment.

Decal

Adjusting

7. Loosen the screws so that the J-handle can be easily

moved in the clamp assembly. Do not remove the

screws or nuts.

8. Slide the J-handle in or out until the arrow/white line

on the decal touches the clamp assembly

(Fig. 2).

9. While holding the unit in the operating position

(Fig. 3), maneuver the J-handle to the location

that provides you the best grip.

10. Tighten the clamp screws evenly, until the J-handle is

secure.

NOTE: Once the new J-handle is installed, there is no

need to change back to the original handle when

you are done using the attachment. Keep this

new handle installed when you use your original

unit as a string head trimmer.

Fig. 2

IDENTIFY & REMOVE YOUR ASSIST HANDLE

Your trimmer is configured with one of many types of

assist handles. You must remove the current assist

handle and install the 24” J-handle (included) in order to

use the TBBC attachment.

Consult your trimmer’s manual to determine what type of

handle you have. Follow the instructions outlined in the

manual in order to remove the current handle and its

clamps, screws, nuts, bolts or other hardware.

NOTE: Your trimmer may be equipped with a small

J–handle. This small handle is NOT an acceptable

substitute for the larger J-handle that is included

with the TBBC. Remove the smaller J-handle so

you can install the larger, 24-inch handle.

Before you can use the TBBC attachment, you must

make some adjustments to the trimmer or trimmer/

brushcutter that you are attaching the TBBC to. You will

have to:

• Remove your current assist handle

• Install the supplied 24” J-handle

• Install the shoulder strap clip (if necessary)

• Attach/adjust the shoulder strap

These instructions are explained on the next couple

pages.

To comply with

safety regulations,

you MUST use the large 24” J-handle that is

included with the attachment when

operating the TBBC. The handle is required

as a barrier bar to the brush blade.

WARNING:

Shaft

Grip

Fig. 1

Fig. 3

ASSEMBLY INSTRUCTIONS

INSTALL THE SHOULDER HARNESS LOOP

When operating the brushcutter attachment, you must

use the shoulder harness that is provided with the unit.

Check to see if your trimmer has a wire form support

fitting that you can clip the strap to. If your unit has the

fitting that is shown in Figure 4, you do not need to install

the harness loop provided. If so, head to the next section

Install the Harness.

Shaft

Grip

Securing

Nut

J-handle

INSTALL THE SHOULDER HARNESS

1. Push the strap through the center of the buckle.

2. Pull the strap over the cross bar and down through

the slot in the buckle (Fig. 6).

3. Put the harness on over head and onto the left

shoulder. Snap it on to the support fitting (Fig. 7).

4. Adjust length to fit the operator’s size. Pull tab to

lengthen, pull strap to shorten (Fig 8).

Fig. 6

Fig. 7

Fig. 8

Always use the

shoulder harness

when using the cutting blade to avoid

serious personal injury.

WARNING:

If your trimmer does not have an existing wire form fitting,

you must install the clip that is included with the TBBC.

To install the supplied shoulder harness clip:

1. Remove the bolt, nut and washer that were installed

on the harness loop for shipping. Keep them handy.

2. Pull the clamp open and push it onto the boom.

3. Arrange the clip so that it is close to the shaft grip

and away from the J-handle (Fig. 5).

4. Insert the bolt through the clip and secure it with the

washer and nut, using a pair of pliers and a small

crescent wrench.

Boom

Wire Form

Support Fitting

Fig. 4

Fig. 5

OPERATING INSTRUCTIONS

OPERATING THE EZ-LINK

™

SYSTEM

The following attachments are also available:

Cultivator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TBGC

Edger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TBLE

Hedge Trimmer . . . . . . . . . . . . . . . . . . . . . . . . . . . TBAH

Straight Shaft Trimmer . . . . . . . . . . . . . . . . . . . . . . TBSS

Turbo Blower . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TBTB

Pole Saw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TBPS

Removing the Add-On

1. Turn the knob counterclockwise to loosen (Fig. 9).

2. Press and hold the release button (Fig. 9).

3. While firmly holding the upper shaft housing, pull the

add-on straight out of the EZ-Link™ coupler (Fig. 10).

Installing the Add-On

NOTE: Place the unit on the ground or on a work bench

to make add-on installation or removal easier.

1. Turn knob counterclockwise to loosen (Fig. 9).

Fig. 9

EZ-Link™ Coupler

Release Button

Guide Recess

Knob

Primary Hole

Upper Shaft Housing

EZ-Link™ Coupler

2. While firmly holding the add-on, push it straight into

the EZ-Link™ coupler (Fig. 10).

NOTE: Aligning the release button with the guide recess

will help installation (Fig. 9).

3. Turn the knob clockwise to tighten (Fig. 9).

Fig. 10

Fig. 11

Knob

Lower Shaft Housing

Release Button

To avoid serious

personal injury and

damage to the unit, shut the unit off before

removing or installing add-ons.

WARNING:

Add-ons are to be

used in the primary

hole only. Using the wrong hole could lead to

personal injury or damage to the unit.

CAUTION:

Lock the release

button in the primary

hole and securely tighten the knob before

operating this unit.

CAUTION:

When using any

attachment, read

and understand that attachment’s specific

manual before you begin operation. Follow all

applicable safety information.

WARNING:

Never use this attachment with an electric-powered unit. Only

attach the TBBC to gas-powered trimmers or brushcutters.

Use with an electric product could lead to damage to the unit or serious personal injury.

WARNING:

USING THE CUTTING BLADE

To establish a rhythmic cutting procedure:

• Plant feet firmly, comfortably apart.

• Bring the engine to full throttle before entering the

material to be cut. At full throttle the blade has

maximum cutting power and is less likely to bind, stall

or cause blade thrust (which can result in serious

personal injury to the operator or others).

• Cut while swinging the upper part of your body from

left to right.

• Always release the throttle trigger and allow the engine

to return to idle speed when not cutting.

• When you are finished, always unsnap the unit from

the harness before taking off the harness.

• Maneuver the unit in the opposite direction as the

blade spins, which increases the cutting action.

Always wear eye,

hearing, foot, body

protection and the shoulder strap to reduce the

risk of injury when operating this unit.

WARNING:

Do not use the

cutting blade for

edging or as an edger. Severe personal injury

to yourself or others can result.

WARNING:

ade thrust may

occur when the

spinning blade contacts an object that it does

not immediately cut. Blade thrust can be

violent enough to cause the unit and/or

operator to be propelled in any direction, and

possibly lose control of the unit. Blade thrust

can occur without warning if the blade snags,

stalls or binds. This is more likely to occur in

areas where it is difficult to see the material

being cut.

WARNING:

OPERATING INSTRUCTIONS

HOLDING THE UNIT

Before operating the unit, stand in the operating position

(Fig. 12). Check for the following:

• The operator is wearing eye protection and proper

clothing

• With a slightly-bent right arm, the operator’s right hand

is holding the shaft grip

• The operator’s left arm is straight, the left hand holding

the J-handle

• The unit is at waist level

• The cutting blade is parallel to the ground and easily

contacts the weeds or brush without the need to bend

over

Once you are in the operating position, hook the

shoulder strap to the unit. Check the length of the strap

before operating. If it needs adjustment, refer to Step 4

of Install the Shoulder Harness.

Fig. 12

Always wear eye,

hearing, foot and

body protection to reduce the risk of injury

when operating this unit.

WARNING:

The blade continues

to spin after the

engine is turned off. The coasting blade can

seriously cut you if accidentally touched.

WARNING:

Never use this attachment with an electric-powered unit. Only

attach the TBBC to gas-powered trimmers or brushcutters.

Use with an electric product could lead to damage to the unit or serious personal injury.

WARNING:

OPERATING INSTRUCTIONS

Fig. 13

• After the return swing, move forward to the next area

to be cut plant your feet again.

• The cutting blade is designed with a second cutting

edge. You can use it by removing the blade, turning it

upside down, and reinstalling it.

To reduce the chance of material wrapping around the

blade, follow these steps:

• Cut at full throttle

• Swing the unit into material to be cut from your left to

your right (Fig. 13)

• Avoid the material just cut as you make the return swing

Do not clear away

any cut material with

the engine running or blade turning. To avoid

serious personal injury, turn off the engine.

Allow the blade to stop before removing

materials wrapped around the blade shaft.

WARNING:

Do not sharpen the

cutting blade.

Sharpening the blade can cause the blade tip

to break off while in use. This can result in

severe personal injury to yourself or others.

Replace the blade.

WARNING:

MAINTENANCE AND REPAIR INSTRUCTIONS

Install the New Cutting Blade

1. Place the cutting blade on the output shaft bushing

(Fig. 16).

Shield

Mount

Locking Rod

Cutting

Blade

Blade Retainer

Nut

Output Shaft

Bushing

Pilot Hole

Fig. 16

To avoid serious

personal injury,

always wear gloves while handling or

installing the blade.

WARNING:

REPLACING THE CUTTING BLADE

When the cutting blade gets dull, you need to replace it.

Never sharpen a dull blade. Follow the instructions in this

section to successfully replace the blade.

Remove the Cutting Blade

NOTE: To make cutting blade removal and installation

easier, place the unit on the ground or on a work

bench

1. Align the shaft bushing hole with the locking rod slot

and insert the locking rod into the bushing hole (Fig. 14).

Clockwise

Fig. 15

4. Remove the nut, blade retainer and blade. Store the

nut and blade together for future use in a secure

place. Store out of children’s reach.

To avoid serious

personal injury,

always wear gloves while handling or

installing the blade.

WARNING:

Fig. 17

Pilot Step

2. Make sure that the cutting blade is centered on the

pilot step and sitting flat against the output shaft

bushing (Fig. 17).

If the cutting blade

is off-center, the

unit will vibrate and the blade may fly off,

causing possible serious personal injury.

WARNING:

Shaft Bushing Hole

Locking Rod Slot

Output Shaft

Bushing

Locking Rod

Output Shaft

Fig. 14

The gear housing

gets hot with use. It

can result in injury to the operator. The

housing remains hot for a short time even

after the unit is turned off. Do not touch the

gear housing until it has cooled.

WARNING:

2. Hold the locking rod in place by grasping it next to

the boom of the unit (Fig. 15).

3. While holding the locking rod, loosen the nut on the

blade by turning it clockwise with a 13 mm closed-

end or socket wrench (Fig. 15).

MAINTENANCE AND REPAIR INSTRUCTIONS

CLEANING

Use a small brush to clean off the outside of the unit. Do

not use strong detergents. Household cleaners that

contain aromatic oils such as pine and lemon, and

solvents such as kerosene, can damage plastic housing

or handle. Wipe off any moisture with a soft cloth.

STORAGE

• Store the unit locked up to prevent unauthorized use or

damage.

• Store the unit in a dry, well-ventilated area.

• Store the unit out of the reach of children.

To avoid serious

personal injury,

always turn your unit off and allow it to cool

before you clean or service it.

WARNING:

Fig. 18

6. Remove the locking rod from the locking rod slot.

1/4-1/2 turn

Counterclockwise

3. Align the shaft bushing hole with the locking rod

slot and insert the locking rod into the bushing hole

(Fig. 14).

4. Put the blade retainer and nut on the output shaft.

Make sure that the blade is installed correctly.

5. Tighten nut counterclockwise against the blade while

holding the locking rod:

• If using a torque wrench and an 13 mm socket tighten

to: 325 - 335 in•lb, 27 - 28 ft.•lb, 37 - 38 N•m.

• Without a torque wrench, use a 13 mm closed-end or

socket wrench, turning the nut until the blade retainer

is snug against the shaft bushing. Make sure that the

blade is installed correctly, then rotate the nut an

additional 1/4 to 1/2 turn counterclockwise (Fig. 18).

Do not sharpen the

cutting blade.

Sharpening the blade can cause the blade tip

to break off while in use. This can result in

severe personal injury. Replace the blade.

WARNING:

To avoid serious

personal injury or

damage to the unit, do not start or operate this

unit with the locking rod in the locking rod slot.

WARNING:

SPECIFICATIONS

*All specifications are based on the latest product information available at the time of printing. We reserve the right to

make changes at any time without notice.

Approximate Attachment Weight ............................................................................................................... 3.75 lbs. (1.7 kg)

Cutting Path Diameter, Cutting Blade ..................................................................................................... 8 inches (204 mm)

Shoulder Harness ................................................................................................................................... Single Quick-Snap

MANUFACTURER’S LIMITED WARRANTY FOR:

No implied warranty, including any implied warranty

of merchantability or fitness for a particular purpose,

applies after the applicable period of express written

warranty above as to the parts as identified. No other

express warranty or guaranty, whether written or

oral, except as mentioned above, given by any

person or entity, including a dealer or retailer, with

respect to any product shall bind Troy-Bilt. During

the period of the Warranty, the exclusive remedy is

repair or replacement of the product as set forth

above. (Some states do not allow limitations on how

long an implied warranty lasts, so the above limitation

may not apply to you.)

The provisions as set forth in this Warranty provide

the sole and exclusive remedy arising from the sales.

Troy-Bilt shall not be liable for incidental or

consequential loss or damages including, without

limitation, expenses incurred for substitute or

replacement lawn care services, for transportation

or for related expenses, or for rental expenses to

temporarily replace a warranted product. (Some

states do not allow limitations on how long an implied

warranty lasts, so the above limitation may not apply to

you.)

In no event shall recovery of any kind be greater than

the amount of the purchase price of the product sold.

Alteration of the safety features of the product shall void

this Warranty. You assume the risk and liability for loss,

damage, or injury to you and your property and/or to

others and their property arising out of the use or

misuse or inability to use the product.

This limited warranty shall not extend to anyone other

than the original purchaser, original lessee or the person

for whom it was purchased as a gift.

How State Law Relates to this Warranty: This

warranty gives you specific legal rights, and you may

also have other rights which vary from state to state.

To locate your nearest service dealer dial 1-800-520-

5520 in the United States or 1-800-668-1238 in Canada.

Troy-Bilt LLC

P.O. Box 361131

Cleveland, OH 44136-0019

The limited warranty set forth below is given by Troy-Bilt

LLC (“Troy-Bilt”) with respect with new merchandise

purchased and used in the United States, its

possessions and territories.

Troy-Bilt warrants this product against defects in

material and workmanship for a period of two (2) years

commencing on the date of original purchase and will, at

its option, repair or replace, free of charge, any part

found to be defective in material or workmanship. This

limited warranty shall only apply if this product has been

operated and maintained in accordance with the

Operator’s Manual furnished with the product, and has

not been subject to misuse, abuse, commercial use,

neglect, accident, improper maintenance, alteration,

vandalism, theft, fire, water or damage because of other

peril or natural disaster. Damage resulting from the

installation or use of any accessory or attachment not

approved by Troy-Bilt for use with the product(s)

covered by this manual will void your warranty as to any

resulting damage.

This warranty is limited to ninety (90) days from the date

of original retail purchase for any Troy-Bilt product that

is used for rental or commercial purposes, or any other

income-producing purpose.

HOW TO OBTAIN SERVICE: Warranty service is

available, WITH PROOF OF PURCHASE THROUGH

YOUR LOCAL AUTHORIZED SERVICE DEALER. To

locate the dealer in your area, please check for a listing

in the Yellow Pages or contact the Customer Service

Department of Troy-Bilt by calling 1-800-520-5520 or

writing to P.O. Box 361131, Cleveland OH 44136-0019

or if in Canada call 1-800-668-1238. No product

returned directly to the factory will be accepted unless

prior written permission has been extended by the

Customer Service Department of Troy-Bilt.

This limited warranty does not provide coverage in

the following cases:

A. Tune-ups - Spark Plugs, Carburetor Adjustments,

Filters

B. Wear items - Bump Knobs, Outer Spools,Cutting

Line, Inner Reels, Starter Pulley,Starter Ropes, Drive

Belts

C. Troy-Bilt does not extend any warranty for products

sold or exported outside of the United States of

America, its possessions and territories, except

those sold through Troy-Bilt’s authorized channels of

export distribution.

Troy-Bilt reserves the right to change or improve the

design of any Troy-Bilt product without assuming any

obligation to modify any product previously

manufactured.

Manuel de L'utilisateur

IMPORTANT: LISEZ LES RÈGLES ET CONSIGNES DE SÉCURITÉ SOIGNEUSEMENT

P/N 769-02046A (5/06)

Débroussailleuse

TBBC

Ne jamais utiliser cet accessoire avec un

appareil électrique. N'attachez le TBBC qu'à des

coupe-bordures ou des débroussailleuses à essence. L'utilisation avec un produit

électrique pourrait endommager l'appareil ou entraîner des blessures.

AVERTISSEMENT:

INTRODUCTION

Copiez le numéro

de série ici :

Copiez le numéro de

modèle / pièce mère ici :

TOUS NOS REMERCIEMENTS

Nous vous remercions d'avoir acheté ce produit de

qualité. Cet outil mécanique de plein air moderne est

conçu pour vous rendre service pendant longtemps. Il

vous sauvera beaucoup de temps comme vous pourrez

vous en rendre compte. Ce manuel de l'utilisateur

comporte un mode d'emploi facile à comprendre. Prenez

soin de lire le manuel au complet et suivez toutes ses

instructions à la lettre afin de conserver votre nouvel outil

mécanique de plein air en excellent état de

fonctionnement.

RÉFÉRENCES, ILLUSTRATIONS ET

SPÉCIFICATIONS RELATIVES AU PRODUIT

Toutes les informations, illustrations et spécifications

contenues dans ce manuel tiennent compte des

dernières informations techniques disponibles au

moment de mettre sous presse. Nous nous réservons le

droit d'y apporter des modifications à tout moment, sans

préavis.

réservés.

INFORMATIONS D’ENTRETIEN

Obtenez la liste des concessionnaires agréés appelez le

1-800-520-5520 aux États-Unis ou le 1-800-668-1238

au Canada. Pour de plus amples informations à propos

de votre appareil, visitez www.troybilt.com.

NE RETOURNEZ PAS L'APPAREIL AU DÉTAILLANT

CHEZ QUI VOUS L'AVEZ ACHETÉ. TOUT SERVICE

SOUS GARANTIE NÉCESSITE UNE PREUVE

D'ACHAT.

CE PRODUIT EST COUVERT PAR UN OU PLUSIEURS

BREVETS AMÉRICAINS, ET D’AUTRES SONT EN

INSTANCE.

Tout entretien effectué sur cet appareil pendant et après

la période de garantie doit être fait par un concess-

ionnaire agréé uniquement.

S/N :

ITEM :

MODEL :

TABLE DES MATIÈRES

Service technique . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Consignes de sécurité . . . . . . . . . . . . . . . . . . . . . . .3

Familiarisez-vous avec votre appareil . . . . . . . . . . .7

Instructions de montage . . . . . . . . . . . . . . . . . . . . . .8

Mode d'emploi . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Entretien et réparations . . . . . . . . . . . . . . . . . . . . .13

Caractéristiques . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Garantie . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Liste des pièces . . . .Intérieure de la Couverture Arrière

Numéro de modèle

Numéro de série

Numéro de pièce mère

Si vous éprouvez des difficultés à assembler ce produit

ou si vous avez des questions concernant les

commandes, le fonctionnement ou l’entretien de cet

appareil, veuillez communiquer avec notre service

technique.

CONSIGNES DE SÉCURITÉ

SYMBOLE SIGNIFICATION

Les symboles de sécurité attirent votre attention sur

des dangers potentiels. Ces symboles et leurs détails

explicatifs méritent que vous les lisiez et compreniez

bien. Les avertissements de sécurité ne peuvent éviter

les dangers de par eux-mêmes. Les consignes ou

mises en garde qu'ils donnent ne remplacent pas des

mesures préventives appropriées contre les accidents.

REMARQUE: donne des informations ou des

instructions vitales pour le fonctionnement ou

l'entretien de l'équipement.

le non-

respect d’un

avertissement peut causer dommages matériels

ou blessures graves à vous-même et d’autres

personnes. Respectez les consignes de sécurité

afin de réduire les risques d'incendie,

d'électrocution et de blessures.

AVERTISSEMENT:

le non-respect d’un

avertissement peut

causer des dommages

matériels ou des blessures graves à vous-même

et d’autres personnes. Respectez les consignes

de sécurité afin de réduire les risques d'incendie,

d'électrocution et de blessures.

DANGER:

le non-

respect

d’un avertissement peut causer dommages

matériels ou blessures graves pour tous.

Respectez toujours les consignes de sécurité

afin de réduire les risques d'incendie,

d'électrocution et de blessures.

MISE EN GARDE:

indique un danger, un avertissement ou une

mise en garde. Soyez vigilant afin d'éviter toute

blessure grave. Ce symbole peut être combiné

à d'autres symboles ou pictogrammes.

ALERTE DE SÉCURITÉ:

Lisez le(s) manuel(s) de l'utilisateur et suivez tous les

avertissements et consignes de sécurité. Vous

pourriez à défaut entraîner des blessures graves pour

vous ou d'autres personnes.

SI VOUS AVEZ DES QUESTIONS, APPELEZ LE

1-800-520-5520

• IMPORTANTES CONSIGNES DE SÉCURITÉ •

LISEZ TOUTES LES INSTRUCTIONS AVANT

L’UTILISATION

• Lire les instructions attentivement. Se familiariser avec

les commandes et l’utilisation correcte de cet outil.

• Ne pas utiliser l’outil si vous êtes fatigué, malade ou

sous l’effet de l’alcool, de drogues ou de médicaments.

• Les enfants de moins de 15 ans ne doivent pas utiliser

l’outil, exception faite des adolescents sous

surveillance d’un adulte.

• Toutes les protections et tous les accessoires de

sécurité doivent être en place avant d’utiliser l’outil.

•I

nspecter l’outil avant utilisation. Remplacer les pièces

endommagées. Regarder s’il y a des fuites de carburant.

Vérifier que toute la boulonnerie est bien serrée et qu’aucune

pièce ne manque. Remplacer les pièces de l’accessoire de

coupe fêlées, ébréchées ou endommagées. Ne pas utiliser

l’outil si des pièces sont desserrées ou endommagées.

• Être conscient du risque de blessures à la tête, les

mains et les pieds.

• Inspecter soigneusement la zone de travail avant de

démarrer l’outil. Éliminer tous les débris tels que

morceaux de verre, fil de fer, etc.

• Éloigner toutes les personnes et animaux de la zone

de travail. Prévoir une zone de sécurité dans un rayon

d’au moins 15 m (50 pi) tout en restant conscient que

des objets risquent d’être projetés au-delà de cette

zone et blesser quelqu’un. Il est recommandé à toute

personne se trouvant à proximité de porter des

lunettes de sécurité. Arrêter immédiatement le moteur

si quelqu’un s’approche.

• N'utiliser qu'avec des coupe-bordures à essence

prévues pour des accessoires et dont l'interrupteur

On/Off se trouve sur la poignée.

Ne jamais utiliser cet accessoire avec un

appareil électrique. N'attachez le TBBC qu'à des

coupe-bordures ou des débroussailleuses à essence. L'utilisation avec un produit

électrique pourrait endommager l'appareil ou entraîner des blessures.

AVERTISSEMENT:

Commande

Marche/Arrêt Stop

(sur la poignée)

Lorsque

vous utilisez

cette

machine, vous devez respecter les consignes de

sécurité. Veuillez lire attentivement ces instructions

avant d'utiliser la machine pour vous assurer de la

sécurité de l'opérateur et de toute personne dans

les alentours. Conservez ces instructions pour un

usage ultérieur.

AVERTISSEMENT:

CONSIGNES DE SÉCURITÉ

AVERTISSEMENTS DE SÉCURITÉ CONCERNANT

LES OUTILS À MOTEUR À ESSENCE

• Ne conserver le carburant que dans des récipients

spécialement conçus et homologués pour le stockage

de ce type de produit.

• Toujours arrêter le moteur et le laisser refroidir avant

faire l’appoint de carburant. Ne jamais retirer le

bouchon du réservoir de carburant ou faire l’appoint

pendant que le moteur est chaud. Ne jamais utiliser

l’outil sans que le bouchon du réservoir soit bien en

place. Desserrer le bouchon lentement afin de relâcher

la pression du réservoir.

• Mélanger et ajoutez le carburant dans un endroit bien

aéré et propre, en plein air, à l’abri des sources

d’étincelles ou flammes vives. Ne retirer (lentement) le

bouchon du réservoir d’essence qu’après avoir arrêté

le moteur. Ne pas fumer pendant l’approvisionnement

ou le mélange de carburant. Essuyer immédiatement le

carburant répandu sur l’outil.

• Éviter de créer une source d’allumage pour le carburant

répandu. Ne pas lancer le moteur avant que toutes les

vapeurs se soient dissipées.

• Éloigner l’outil d’au moins 9 m (30 pi) du point

d’approvisionnement en carburant avant de démarrer

le moteur. Ne pas fumer et éloigner toute source

d’étincelles ou de flammes vives du point

d’approvisionnement ou d’utilisation de l’outil.

• Appuyez sur la manette des gaz et assurez-vous

qu'elle revient automatiquement en position de ralenti.

Procédez à tous les réglages ou réparations avant

d'utiliser l'appareil.

• Ne pas toucher le moteur, la boîte de vitesses ou

l'échappement. Ces éléments chauffent très fort en

cours d'utilisation et même après avoir arrêté la

machine.

• Pour éviter tout risque d'incendie, remplacer un

échappement ainsi que le pare-étincelles défectueux.

Garder toujours le moteur propre. Éviter l'accumulation

d'herbe, de feuilles, de graisse ou de carbonne.

• Évitez de démarrer ou de faire marcher l'appareil à

l'intérieur d'une pièce ou d'un bâtiment fermé. La

respiration de fumées d'échappement peut tuer. Ne

faites fonctionner cet appareil qu'à l'extérieur dans un

endroit bien aéré.

PENDANT L'UTILISATION DE L'APPAREIL

• Lire attentivement et vous assurer de bien comprendre

les consignes de sécurité avant d'utiliser cette machine

• Inspecter soigneusement la machine pour des boulons

et écrous dévissés ou d'autres pièces endommagées

avant de continuer. Réparer ou remplacer si

nécessaire.

• Portez des lunettes de sécurité conformes aux normes

ANSI Z87.1 ainsi que des protège-oreilles durant

l'utilisation de l'appareil. Portez un masque facial ou

antipoussières si vous travaillez dans un lieu

poussiéreux.

• Portez des pantalons épais et longs, des bottes, des

gants et une chemise à manches longues. Ne marchez

pas pieds nus et évitez les vêtements lâches, bijoux,

pantalons courts et sandales. Relevez les cheveux au-

dessus des épaules.

• Ajustez la poignée selon votre taille pour mieux

l'agripper.

• N'utilisez l'appareil qu'en plein jour ou avec un bon

éclairage artificiel.

• Évitez tout démarrage accidentel. Mettez-vous en

position de démarrage chaque fois que vous tirez sur

la corde de démarrage. L'opérateur et l'appareil

doivent tous deux être en position stable à ce moment-

là. Voir les Instructions de démarrage et d'arrêt.

• Toujours utiliser l'outil adéquat. N'utiliser l'outil que

pour la tâche pour laquelle il a été conçu.

• Ne vous étirez pas. Tenez-vous toujours bien sur vos

pieds en position d'équilibre.

• Tenez toujours l'appareil des deux mains lorsque vous

le faites marcher. Agrippez fermement les poignées

avant et arrière.

• Gardez les mains, le visage et les pieds éloignés des

pièces mobiles.

• Le TBBC est spécialement agréé pour être utilisé avec

les modèles suivants des coupe-bordures acceptant

des accessoires:

Ryobi: Troy-Bilt:

775R TB20CS

750R TB25CS

790R TB25ET

890R TB70SS

TB75SS

Yard Man:

TB90BC

YM25 TB425CS

YM75 TB475SS

YM90 TB490BC

YM26BC

Bolens (Canada):

Cub Cadet:

BL26BC

CC2025

CC3075

Yardworks:

CC4025 60-2310-6

CC4075 60-2311-4

CC4090 60-2312-2

l'essence

est

extrêmement inflammable et ses vapeurs

peuvent exploser si on y met le feu. Veuillez

prendre les précautions suivantes.

AVERTISSEMENT:

La page charge ...

Ryobi TBBC Manuel utilisateur

Marque: Ryobi

Modèle: TBBC

Taper: Manuel utilisateur

Ce manuel convient également à

Brush Cutter TBBC

Télécharger le PDF

rapport

dans d''autres langues

English: Ryobi TBBC User manual
español: Ryobi TBBC Manual de usuario

Documents connexes

Ryobi TBBC Manuel utilisateur

Ryobi TBBC Manuel utilisateur

Ce manuel convient également à

Ryobi TBBC Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents