JennAir JJB6424HM Le manuel du propriétaire

Marque: JennAir

Modèle: JJB6424HM

Catégorie: Accessoires de préparation de café

Taper: Le manuel du propriétaire

Ce manuel convient également à

JJB6424HL

JENNAIR

BUILT-IN COFFEE SYSTEM

MACHINE À ESPRESSO ENCASTRÉE JENNAIR

W11325607B

Use & Care Guide

For questions about features, operation/performance, parts, accessories, or service in the U.S.A., call:

1-800-JENNAIR (1-800-536-6247) or visit our website at www.jennair.com.

In Canada, call: 1-800-JENNAIR (1-800-536-6247) or visit our website at www.jennair.ca.

Guide d’utilisation et d’entretien

Pour des questions à propos des caractéristiques, du fonctionnement/rendement, des pièces, accessoires ou dépannage,

composerle:1-800-JENNAIR (1-800-536-6247) ou visitez notre site Web au www.jennair.com.

Au Canada, composer le 1800JENNAIR (1800536-6247) ou visiter notre site Web au www.jennair.ca.

TABLE OF CONTENTS TABLE DES MATIÈRES

COFFEE SYSTEM SAFETY ..........................................................3

PARTS AND FEATURES ................................................................4

BEFORE USING THE COFFEE SYSTEM ......................................6

COFFEE SYSTEM USE ..................................................................7

Settings ........................................................................................7

Selecting Coffee Strength ..........................................................10

Making Coffee or Espresso Using Coffee Beans ......................10

Selecting the Coffee Size ...........................................................11

Adjusting the Coffee Mill ............................................................11

Making Coffee using Pre-Ground Coffee ..................................12

Making Milk-Based Hot Drinks ..................................................12

Delivering Hot Water ..................................................................14

Steam Delivery ...........................................................................14

COFFEE SYSTEM CARE .............................................................14

General Cleaning ........................................................................14

TROUBLESHOOTING ..................................................................17

ASSISTANCE OR SERVICE .........................................................22

In the U.S.A. ...............................................................................22

In Canada ...................................................................................22

WARRANTY ..................................................................................23

SÉCURITÉ DE LA MACHINE À ESPRESSO .............................24

PIÈCES ET CARACTÉRISTIQUES ..............................................25

AVANT D’UTILISER LA MACHINE À ESPRESSO ......................27

UTILISATION DE LA MACHINE À ESPRESSO ..........................28

Settings (réglages) ......................................................................28

Sélection de l’intensité du café ..................................................32

Préparer une boisson ou unexpresso en utilisant

desgrainsdecafé ......................................................................32

Sélection de la taille de la tasse decafé ....................................33

Réglage du moulin à café ..........................................................33

Préparer une boisson en utilisant ducafé déjà moulu ..............33

Préparer une boisson à base de lait ..........................................34

Verser de l’eau chaude ...............................................................35

Préparation de vapeur ................................................................35

ENTRETIEN DE LA MACHINE À ESPRESSO ............................36

Nettoyage général ......................................................................36

DÉPANNAGE .................................................................................39

ASSISTANCE OU DÉPANNAGE ..................................................44

Aux É.-U. ....................................................................................44

Au Canada ..................................................................................44

GARANTIE .....................................................................................45

COFFEE SYSTEM SAFETY

You can be killed or seriously injured if you don't immediately

You

can be killed or seriously injured if you don't

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

follow instructions.

instructions.

DANGER

WARNING

IMPORTA NT SAFETY INSTRUCTIONS

To reduce the risk of fire, electric shock, or injury to persons when using the appliance, follow basic precautions,

including the following:

WARNING:

SAVE THESE INSTRUCTIONS

■

Read all instructions before using the appliance.

■

Do not touch hot surfaces. Use handles or knobs.

■ To protect against fire, electric shock and personal injury

do not immerse cord, plugs, or appliance in water or other

liquids.

■

The appliance is not intended for use by young children or

infirm persons without supervision.

■

Unplug from outlet when not in use and before cleaning.

Allow to cool before putting on or taking off parts, and

before cleaning.

■ Do not operate any appliance with a damaged cord or

plug, or after appliance malfunctions or has been

damaged in any manner. Return the appliance to the

nearest authorized service center for examination, repair or

adjustment.

■

The use of accessory attachments not recommended by

the appliance manufacturer may result in ﬁre, electric

shock, or personal injury.

■ Do not use outdoors.

■ Do not let cord hang over edge of table or counter, or

touch hot surfaces.

■ Do not place on or near a hot gas or electric burner, or in a

heated oven.

■ Always switch the appliance off, then plug cord into the

wall outlet. To disconnect, turn the appliance off, then

remove plug from wall outlet.

■ Do not use appliance for other than intended use.

■ Use extreme caution when using hot steam.

■ Check hopper for presence of foreign objects before using.

PARTS AND FEATURES

This manual covers several models. The coffee system you have purchased may have some or all of the items listed. The locations and

appearances of the features shown here may not match those of your model.

Coffee System:

PUSH

AC B

FGH

L M N

A. Beans container lid

B. Pre-ground door

C. Grinding adjustment dial

D. Beans container

E. Ground coffee funnel

F. Infuser

G. Coffee guide

H. Service door

I. Cup holder tray

J. Coffee grounds container

K. Drip tray

L. Coffee spouts (adjustable height)

M. Lights to illuminate cup

N. Hot water/steam connection nozzle

O. Water tank

P. Storage tray

Q. Main ON/OFF switch

R. Measure holder

S. Cup warming ledge

T. Power cord

U. Lighting to illuminate interior

compartment

V. Control panel

W. On/standby button

Accessories:

Milk and Accessories Container:

A. "Total Hardness Test" indicator paper

B. Ground coffee measure

C. Cleaning brush

D. Hot water/steam spout

E. Connection nozzle cover

A. Froth adjustment and CLEAN

function dial

B. Lid release buttons

C. Thermal casing

D. Milk container

E. Milk intake tube

F. Adjustable frothed milk spout

G. Lid with milk frother

*Water lter not available on this model.

BEFORE USING THE COFFEE SYSTEM

NOTE: This product is intended for household use only.

Coffee has been used to factory test the machine. It is completely

normal for there to be traces of coffee in the mill.

Customize water hardness as soon as possible. See “Water

Hardness” in the “Settings” section.

IMPORTANT: Complete the following steps before the coffee

system is used for the rst time.

1. INSERT WATER OUTLET: Check that the hot water/steam

spout is inserted on the connection nozzle.

2. Turn on the coffee system.

3. To select a language, press or until the ag

corresponding to the required language appears on the

display, then press the ag.

4. FILL WATER TANK WITH FRESH WATER: Remove the water

tank, open the lid and ll to the MAX line with fresh water.

Replace water tank.

5. Place a container with a minimum capacity of 1/2 cup (100 mL)

underneath.

WATER CIRCUIT EMPTY PRESS OK TO START FILLING

PROCESS will show on display. Press

to conrm.

6. The coffee system will deliver fresh water from the spout then

turns off automatically. The coffee system is now ready for

normal use.

NOTES:

■ When rst using the coffee system, you need to make

4-5 cappuccinos before the coffee system gives good results.

■ Before turning the coffee system on, make sure the main

switch is turned on. Each time the coffee system is turned on,

it performs an automatic preheat and rinse cycle which cannot

be interrupted. The coffee system is ready for use only after

the cycle is complete.

A. Hot water and steam nozzle

B. Hot water spout

A. Water tank

COFFEE SYSTEM USE

Settings

You can control several settings through the Settings Menu:

Rinsing, Beep, Statistics, Cup Warmer, Water Hardness, Auto-Off,

Coffee Temperature, Descaling, Auto-Start, Set Language, Set

Time, Cup Lighting, Drink Settings, Energy Saving, Background,

Demo Mode and Default Values.

To access the Settings Menu, press MENU. To exit the Settings

Menu, press ESC.

Rinsing

Use this function to rinse the coffee spouts and preheat the

brewing unit. Place a container with a minimum capacity of

1/2 cup (100 mL) under the coffee and hot water spouts.

1. Press to enter the menu.

2. Press or until the display shows RINSING.

3. Press to start rinsing.

4. After a few seconds, hot water will come out of the coffee

spout and RINSING HOT WATER RUNNING will be displayed.

5. To stop the rinsing cycle, press

STOP

or wait for rinsing to

stop automatically.

IMPORTANT: Do not leave the coffee system unattended while

hot water is being delivered.

NOTES:

■ If the coffee system is not used for more than 3-4 days, we

strongly recommend doing 2-3 rinse cycles before use.

■ After rinsing, it is normal for some water to remain in the

grounds container.

Beep

This function will enable or disable tones that sound when an icon

is pressed or an accessory is inserted/removed.

1. Press to enter the menu.

2. Press or until the display shows BEEP.

3. Press to enable or disable the sound

notication. Press

ESC

to return to the home page.

Statistics

This function displays statistical data relating to the coffee

system.

1. Press to enter the menu.

2. Press or until the display shows STATISTICS.

3. Press . It is possible to check all the available statistics by

pressing or . Press

ESC

to return to the home page.

Cup Warmer

Use to warm cups before making coffee.

1. Press to enter the menu.

2. Press or until the display shows CUP WARMER.

3. Press to active or deactivate the cup

warmer.

4. Press

ESC

to return to the home page.

00:00

User 2 Size

Strength

Espresso Coee

Cappuccino Latte

macchiato

A. Menu to customize beverages settings

B. Appliance settings menu

C. Selected strength

D. Clock

E. Selected size

F. Strength selection

G. Size selection

H. Right scroll arrow

I. Selectable drinks (press on the scrolling

arrows to see all the drinks)

J. Left scroll arrow

K. Customizable proles (see “Memorizing

Your Personal Prole”)

Water Hardness

NOTE: The water hardness level is factory set at level 4. The

coffee system can be programmed according to the hardness of

your fresh water so the coffee system can be descaled less.

1. Remove the "Total hardness test" indicator paper provided

from the packaging.

2. Immerse the paper completely in a glass of fresh water for

about a second.

3. Remove the paper and shake lightly. After a minute, 1, 2, 3, or

4 squares will form. Each square corresponds to one level.

4. Press to enter the menu. Press or until the display

shows WATER HARDNESS.

5. To change the level selected, press the symbol itself until the

required level is displayed (Level 1 = soft water, Level 4 = very

hard water). Press

ESC

to return to the home page.

Auto-Off

Auto-off can be set so the coffee system turns off after 15 or 30

minutes, as well as 1-3 hours of no use.

1. Press to enter the menu.

2. Press or until the display shows AUTO-OFF together

with the current selection (15 or 30 minutes, 1, 2 or 3 hours).

3. Press to select the required value; then press

ESC

return to the homepage.

Coffee Temperature

1. Press to enter the menu.

2. Press or until the display shows COFFEE

TEMPERATURE together with the current selection (LOW,

MEDIUM, HIGH, or MAX).

3. Press to select the required temperature.

4. Press

ESC

to return to the home page.

Descaling

IMPORTANT: Before using, read the instructions and labels on

the descaler packaging.

Descale the appliance when the display shows DESCALING

NEEDED PRESS OK TO START (~45 min) . To descale

immediately, press

and follow the steps.

1. "REMOVE WATER FILTER" will show on the display (if

present). Remove the water lter (if present) and empty the

water tank. Press

2. ADD DESCALER (UP TO LEVEL A) AND FRESH WATER (UP

TO LEVEL B): Pour the descaler into the tank up to level A

marked inside the water tank. This is equal to one 100 mL

packet. Add 1 L (1 qt) fresh water up to level B and replace

tank. Press

3. EMPTY GROUND CONTAINER AND DRIP TRAY: Remove,

empty and replace drip tray and the grounds container.

4. PLACE 2.5 L (3 qt) CONTAINER UNDER OUTLET, PRESS OK

TO START DESCALING: Place an empty 2.5 L (3 qt) or larger

container under the hot water/steam spout and coffee spout.

5. Press

to conrm that descaling solution has been

added. The display will show DESCALING PLEASE WAIT,

which means the program has been started.

6. Descaler will come out of the hot water/steam and coffee

spouts. A series of rinses and pauses is automatically carried

out to remove all scale residue from the inside the coffee

maker.

7. After approx. 25 minutes, descaling will stop; RINSE AND

FILL WATER TANK UP TO MAX LEVEL will display. Empty the

container used for descaler solution and place back under the

spouts. Remove water tank, empty, rinse and rell to the MAX

level and replace tank. Press

A. Water tank

*Water lter not available on this model.

8. Display will show RINSING PLEASE WAIT and hot water will

empty from the spouts.

9. When the fresh water has run out, empty the container used

to collect the fresh water from the spouts.

10. INSERT FILTER INTO ITS HOUSING will be displayed.

Press

and remove the water tank. Reinsert the water

lter if it had been removed previously.

NOTE: Water lter not available on this model.

11. RINSE AND FILL WATER TANK UP TO MAX LEVEL will

display. Fill tank up to MAX level with fresh water. Next,

INSERT WATER TANK will be displayed. Place the water tank

back into the coffee system.

12. PLACE 2.5 L (3 qt) CONTAINER UNDER OUTLET PRESS

OK TO START RINSING: Place the empty container used to

collect the descaling solution under the spouts and

press

. Hot water is dispensed and RINSING PLEASE

WAIT is displayed.

13. EMPTY DRIP TRAY: At the end of the rinsing cycle, remove,

empty and replace the drip tray, along with the grounds

container. Replace and press

14. For a few seconds, DESCALE COMPLETE PRESS OK will be

displayed, then the coffee system will turn off. The descaling

process is complete.

NOTE: If you would like to postpone the descaling process until

a later time, press

ESC

. On the display the symbol will

remain as a reminder.

To access the descaling menu when ready:

1. Press to enter the menu.

2. Press or until the display shows DESCALE. Press

to start the descaling cycle. Follow the instructions on the

display until cycle is complete.

Auto-Start

The auto-start time can be set to have the coffee maker ready at

a certain time.

NOTE: To enable this function, the time must be set correctly. To

set the time, see "Setting the Clock."

1. Press to enter the menu.

2. Press or until the display shows AUTO-START .

Select the function by pressing . The time setting panel

will be displayed.

3. Press or corresponding to the hours and minutes until the

required auto-start time is displayed. Press or

to enable or disable auto-start.

4. To conrm, press

. To cancel and return to the home

page, press

ESC

twice.

The auto-start is now set and the symbol will be displayed

next to the time to indicate that the function has been

enabled.

NOTE: When the coffee system is turned off using the main

switch, the auto-start setting will be lost if it had been enabled.

Set Language

1. Press to enter the menu.

2. Press or until the display shows

Hola

Bonjour

Ciao

SET LANGUAGE.

3. Press

Hola

Bonjour

Ciao

. Press or until the ag corresponding to the

required language is shown and select it. Press

ESC

twice

to return to the home page.

Set Time

1. Press to enter the menu.

2. Press or until the display shows SET TIME.

3. Press . The time setting panel will appear.

4. Press or corresponding to the hours and minutes until the

current time is displayed. To conrm, press

. To cancel,

press

ESC

, then press again to return to the home page.

Cup Lighting

1. Press to enter the menu.

2. Press or until the display shows CUP LIGHTING.

3. Press to enable or disable the lights.

Press

ESC

to return to the home page.

Drink Settings

In this section, you can consult your customized settings and

reset the default values for each beverage.

1. Press to enter the menu. Press or until DRINK

SETTINGS appears on the display.

2. The reference user prole is highlighted on the display. The

values are shown on the vertical bars. The manufacturer

default value is indicated by the symbol while the current

set value is highlighted by the lled part of the vertical bar.

3. To go back to the settings menu, press

ESC

. To scroll and

display the beverages, press

. To return to the default

manufacturer values for the beverage shown on the display,

press RESET. CONFIRM RESET will be displayed. To

conrm, press

. To cancel, press

ESC

4. RETURN TO FACTORY will display. Press

The beverage has been reset to the default values. Continue

with the other beverage, or go back to the settings menu.

NOTE: To change the beverages for another prole, go back

to the homepage, select the required prole and repeat the

procedure.

To reset all the beverages in the prole to the default values, see

the "Default Values" section.

Energy Saving

Use this function to enable or disable energy saving mode. When

enabled, the function guarantees reduced energy consumption.

When it is disabled, warming time is reduced.

1. Press to enter the menu. Press or until ENERGY

SAVING appears on the display.

2. Press to enable or disable energy saving.

Press

ESC

to go back to the homepage.

Demo Mode

By using this setting, the main functions of the coffee system are

shown on the display.

1. Press to enter the menu. Press or until the display

shows DEMO MODE. Press to start the demo.

2. To exit DEMO MODE, rst turn the coffee system off by

pressing the . Press the again to go back to the

homepage.

Default Values

This resets all menu settings and programmed quantities back

to the default values (with the exception of the language which

remains as set).

1. Press to enter the menu. Press or until the display

shows DEFAULT VALUES. Press .

2. Press RESET ALL to reset all proles to the original

parameters, otherwise select the required prole (e.g. User 1).

3. RETURN TO FACTORY SETTINGS? RESET ALL will display.

Press

to conrm or

ESC

to leave settings unaltered.

4. FACTORY SETTINGS SET. Press

to conrm.

Customizing Beverages

The strength and size of drinks can be customized.

1. The prole that is needed to be customized needs to be

active. A maximum of six proles are available on the unit. You

can only select one prole to set at a time.

2. From the homepage, press

. Choose the beverage you

wish to customize in order to access the customizing screen,

The relative accessories must be inserted.

3. (Beverages with coffee only) CHOOSE COFFEE STRENGTH

LEVEL will display. Select the required strength by pressing

or and press

4. CUSTOMIZING COFFEE (OR FRESH WATER) SIZE, PRESS

STOP TO SAVE will display. Preparation begins and the coffee

system displays the size customizing screen in the form of a

vertical bar. The star alongside the bar represents the current

size set.

5. When the amount reaches the minimum size you can set, the

display shows

STOP

. Press

STOP

when the required

quantity in the cup is reached. SAVE NEW SETTINGS? will

display. Press YES or NO.

6. The application conrms if the values have been saved or

not (depending on the previous selection). Press

. The

coffee system goes back to the home page.

NOTE: Milk based drinks; the coffee strength is saved rst,

followed by the quantity of milk, then coffee.

Memorizing Your Personal Prole

The coffee system allows you to memorize six different proles,

each associated with a different icon. In every prole the

customized MY beverages STRENGTH and SIZE values are

saved and the order in which all beverages are displayed is based

on the frequency of selection.

To select or enter a prole, press on the prole currently in use,

press or until the required prole is displayed, then press on

the prole.

NOTE: Prole GUEST: Select this prole to deliver beverages

with the default settings. The

function is not active.

Selecting Coffee Strength

Select the required strength from the homepage by pressing

STRENGTH.

(See “Making Coffee using

Pre-Ground Coffee”)

EXTRA LIGHT STRENGTH

LIGHT STRENGTH

MEDIUM STRENGTH

STRONG STRENGTH

EXTRA STRONG STRENGTH

CUSTOM STRENGTH (if programmed) /

STANDARD STRENGTH

After delivering the beverage, the strength setting is reset to the

value.

Making Coffee or Espresso Using

Coffee Beans

IMPORTANT: Do not use green, caramelized or candied coffee

beans as they could stick to the coffee mill and make it unusable.

1. Fill the beans container with coffee beans. Place a cup under

the coffee spout.

2. Lower the spout so that it is as near as possible to the cup.

This helps achieve a better cream.

3. Press or until the required coffee selection is displayed.

Then select your required coffee from the home page:

Espresso, Doppio+, Coffee, Long, X2 Espresso or Americano.

4. Preparation begins and the display shows the image of

the selected beverage together with a progress bar which

gradually lls as preparation proceeds.

A. Coffee spout

NOTE: It is possible to prepare two cups of espresso coffee at

the same time.

1. Press

during preparation of one espresso.

2. While the machine is making coffee, delivery can be

interrupted at any time by pressing

STOP

3. As soon as delivery has ended, to increase the quantity of

coffee in the cup, press

EXTRA

. Once the desired quantity is

reached, press

STOP

4. Once the coffee has been made, the appliance is ready to

make the next beverage.

NOTE: Various messages may be displayed while using the

appliance (FILL TANK, EMPTY GROUNDS CONTAINER, etc.).

Their meanings are explained in section "Displayed messages."

■ For hotter coffee, see "Tips for Hotter Coffee" section.

■ If the coffee comes out in drops, too weak and not creamy

enough or too cold, see the "Adjusting the Coffee Mill" and

"Troubleshooting" sections.

■ If "Energy Saving" mode is active, the rst coffee may take a

few seconds before it is delivered.

To Clean:

After every 14 cups of coffee made, the drip tray needs to be

cleaned and the coffee grounds container emptied.

1. Open the service door on the front by pulling the coffee spout.

2. Remove the drip tray and clean it.

NOTE: When cleaning the coffee system, always fully remove

the drip tray.

3. Empty the coffee grounds container and replace it.

NOTE: Every time the drip tray is removed, the coffee grounds

container must be emptied. Failure to do so may clog the

coffee system.

4. Replace the drip tray and close the service door.

Selecting the Coffee Size

From the home page, select the required size of coffee in the cup

by pressing SIZE.

SMALL SIZE

MEDIUM SIZE

LARGE SIZE

EXTRA LARGE SIZE

CUSTOM SIZE (if programmed) /

STANDARD SIZE

After delivering the beverage, the size setting is reset to the

value.

Adjusting the Coffee Mill

The coffee mill is factory-set and should not require adjustment.

However, if after making the rst few coffees you nd that the

coffee is either too weak and not creamy enough, or delivery is

too slow (a drop at a time), this can be corrected by adjusting the

grinding adjustment dial.

NOTE: The grinding adjustment dial must only be turned when

the coffee mill is in operation during the initial phase of coffee

preparation.

1. If the coffee comes out too slowly or does not come out at

all, a message will be shown GROUND TOO FINE. ADJUST

GRIND LEVEL, turn the coffee mill dial one or two clicks

clockwise.

2. For fuller bodied creamier coffee, turn one click counter-

clockwise towards one. (Do not turn more than one click at a

time. Otherwise the coffee could come out one drop at a

time.)

The effect of these adjustments will only be evident after at least

two cups of coffee have been delivered. If this adjustment does

not obtain the desired result, repeat the correction by turning the

dial another click.

PUSH

A. Coffee grounds container

B. Drip tray

A. Grinding coarseness adjustment knob

A. Counterclockwise for ner grind

B. Clockwise for coarser grind

Making Coffee using Pre-Ground

Coffee

IMPORTANT:

■ Never add pre-ground coffee when the coffee maker is off in

order to avoid it spreading through the inside of the coffee

maker and making it dirty. This could damage the appliance.

■ Never use more than one level measure or it could dirty the

inside of the coffee maker or block the funnel.

1. Press STRENGTH until the display shows (pre-

ground).

2. Open the cover and the pre-ground door.

3. Make sure the funnel is not blocked, then add one level

measure of pre-ground coffee.

4. Place a cup under the coffee spouts, then select your required

coffee from the home page.

5. Preparation begins and the image of the selected beverage

appears on the display, together with a progress bar which

gradually lls as preparation progresses.

NOTES:

■ If you use pre-ground coffee, you can only make one cup of

coffee at a time.

■ While the coffee maker is making coffee, delivery can be

interrupted at any time by pressing

STOP

■ As soon as delivery has ended, to increase the quantity of

coffee in the cup, press

EXTRA

. Once the desired quantity is

reached, press

STOP

■ Once the coffee has been made, the appliance is ready to

make the next beverage.

Making Milk-Based Hot Drinks

1. Remove the lid of the milk container.

2. Fill the container with approximately 1/2 cup (100 mL) of milk

for each cappuccino you want to make. Do not ll above the

MAX line on the milk container. For a denser or more even

froth, use cold skim or partially skim milk.

3. Make sure the milk intake tube is correctly inserted in the

bottom of the milk container lid and place the lid back onto

the container.

A. Center funnel

A. Milk intake tube

B. Rubber washer

4. Remove the hot water/steam spout.

5. Attach the milk container to the nozzle by pushing the bottom

of the container. A tone will sound if the sound notication is

enabled.

6. Place a large cup under the coffee spouts and frothed milk

spout. To move the spout nearer to the cup, simply pull it

downward.

Adjusting the Amount of Froth

Turn the froth adjustment dial on the milk container to adjust the

amount of froth on the milk delivered while making the drinks. See

table below.

DIAL

POSITION

DESCRIPTION RECOMMENDED FOR...

No froth CAFFE LATTE / MILK (hot milk)

Min. froth LATTE MACCHIATO

Max. froth CAPPUCCINO / MILK (frothed

milk)

Making Milk-Based Drinks Automatically

1. Fill the milk container and attach it as described above.

2. Select the required beverage from the home page:

Cappuccino, Latte Macchiato, Caffe Latte, Hot Milk,

Cappuccino+, Espresso Macchiato, Flat White or Cappuccino

Mix.

3. On the display the coffee maker recommends turning the

foam adjustment dial based on the foam requirements for the

original recipe. Turn the dial on top of the milk container lid

and conrm the selection by pressing

4. After a few seconds, preparation begins automatically

and an image of the selected beverage appears on the

display, together with a progress bar which gradually lls as

preparation progresses.

5. Once the coffee has been made, the coffee maker is ready to

make the next beverage.

NOTES:

■ If "Energy Saving" mode is enabled, there may be a few

seconds delay before the beverage is delivered.

■ Press

ESC

to interrupt preparation completely and go back

to the home page.

■ Press

STOP

to interrupt milk or coffee delivery and move on

to the next delivery (if applicable) to complete the beverage.

■ At the end of delivery, to increase the quantity of coffee in the

cup, press

EXTRA

■ Preparation of each milk based drink can be customized.

See "Customizing Beverages" and Memorizing Your Personal

Prole" sections.

■ Do not leave the milk container out of the refrigerator for more

than 15 minutes. The quality of the foam will decrease the

longer the container is out.

A. Hot water and steam nozzle

B. Hot water spout

A. Hot water and steam nozzle

B. Milk container

A. Coffee spouts

B. Milk spout

C. Cup

To Clean Hot Water/Steam Spout:

Always clean the hot water/steam spout after use to avoid the

build-up of milk residues and prevent it from clogging.

1. Place a container under the hot water/steam spout and let a

little fresh water out. See "Delivering Hot Water" section. Stop

delivery by pressing

STOP

2. Wait a few minutes for the hot water/steam spout to cool

down. When cool, remove the spout. Hold the spout steady

with one hand and with the other, turn and detach the

cappuccino maker, pulling it downwards.

3. Also remove the steam connection nozzle by pulling it

downward. Check that the hole in the connection nozzle is not

blocked. If necessary, clean using a toothpick.

4. Wash all parts of the spout thoroughly with a sponge and

warm water. Attach the connection nozzle and the cappuccino

maker onto the spout by pushing it upwards and turning it

clockwise until it is secure.

Delivering Hot Water

1. Make sure the hot water/steam spout is attached correctly to

the hot water/steam connection nozzle.

2. Place a container under the spout as close as possible to

avoid splashes.

3. Select HOT WATER from the home page. The

corresponding image appears on the display, together with a

progress bar which lls gradually as preparation proceeds.

4. The machine delivers hot water, then the delivery stops

automatically. To interrupt hot water delivery manually,

press

STOP

NOTES:

■ If "Energy Saving" mode is active, there may be a few seconds

delay before hot water is delivered.

■ Preparation of hot water can be customized. See "Customizing

Beverages" and "Memorizing Your Personal Prole" sections.

Steam Delivery

1. Make sure the hot water/steam spout is attached correctly to

the hot water/steam connection nozzle. Fill a container with

the liquid to be heated or frothed and immerse the hot water/

steam spout in the liquid.

2. Select STEAM from the homepage. The corresponding

image appears on the display, together with a progress bar

which lls gradually as preparation proceeds and after a few

seconds, steam to heat the liquid is delivered from the hot

water/steam spout.

3. When the required temperature or level of froth is reached,

interrupt steam delivery by pressing

STOP

Tips for using steam to froth milk:

■ When choosing the size of the container, bear in mind that the

liquid doubles or triples in volume.

■ For a richer, denser froth, use skimmed or partially skimmed

milk at refrigerator temperature.

■ For a creamier froth, rotate the container with a slow

movements in a upward motion.

■ To avoid milk with poor froth or large bubbles, always clean

the spout.

COFFEE SYSTEM CARE

General Cleaning

To avoid damage to the coffee system, do not use solvents or

abrasive detergents to clean the coffee system. Use a soft damp

cloth to clean the exterior of the coffee system. Clean all machine

parts regularly.

IMPORTANT: Before any cleaning, turn the coffee system off

using the main On/Off switch and unplug it.

IMPORTANT: Do not immerse the coffee system in water.

Cleaning the Coffee Grounds Container and Drip Tray

When the display shows the message EMPTY GROUNDS

CONTAINER, the grounds container must be emptied and

cleaned. The appliance cannot be used to make coffee until the

container is has been cleaned. Even if it is not full, the empty

grounds container message is displayed 72 hours after the rst

coffee has been prepared. For the 72 hours to be calculated

correctly, the machine must never be turned off with the main

switch.

1. Open the bottom door by rotating it downwards and open.

A. Hot water/steam spout

PUSH

2. Remove drip tray, empty and clean it.

3. Empty and clean the coffee grounds container making sure to

remove all the residue that can be deposited on the bottom.

The brush provided features a spatula especially for this job.

IMPORTANT: Every time the drip tray is removed, the coffee

grounds container must be emptied. If this is not done, the

grounds container may ll up more than expected and clog the

coffee system.

The drip tray has a gray oat as a water level indicator. Empty

and clean the drip tray before the red oat protrudes from the cup

tray. If the drip tray is not emptied, the water can overow and

damage the coffee system.

1. Open the door and remove the drip tray and coffee grounds

container.

2. Empty the drip tray and grounds container and wash them.

3. Replace the drip tray complete with grounds container.

Cleaning the Water Tank

Clean the water tank regularly with a damp cloth and a small

amount of mild detergent. Rinse thoroughly before lling the tank

and putting it back in the appliance.

Cleaning the Coffee Spouts

Clean the coffee spouts regularly with a sponge or cloth. Check

that the holes in the coffee spouts are not blocked. If necessary,

remove coffee deposits with a toothpick.

Cleaning the Pre-Ground Coffee Funnel

Check regularly that the pre-ground coffee funnel is not blocked.

Remove coffee deposits with the brush supplied, if needed.

Cleaning the Inside

Check the inside of the coffee system approximately once a week

for dirt and debris. If necessary, remove coffee deposits with the

supplied brush and a damp sponge or cloth.

Cleaning the Infuser

IMPORTANT: The infuser must not be removed when the

appliance is on. Do not use force to remove the infuser.

1. Make sure the machine is correctly turned off.

2. Open the service door.

3. Remove the drip tray and grounds coffee container.

4. Press the two colored release buttons inwards and at the

same time pull the infuser outwards.

PUSH

A. Coffee grounds container

B. Drip tray

PUSH

A. Coffee grounds container

B. Drip tray

PUSH

A. Release buttons

B. Infuser unit

5. Soak the infuser in fresh water for about ve minutes, then

rinse.

IMPORTANT: Do not use detergent to clean the infuser to

avoid removing the lubricant applied to the inside of the

piston.

6. After cleaning, replace the infuser by sliding it onto the

internal support and pin at the bottom, then push the PUSH

symbol fully until it clicks into place.

NOTE: If you are having difculty replacing the infuser,

compress the moving parts from both the top and bottom as

shown in the following illustration before reinserting it.

7. Once inserted, make sure the two colored release buttons

have snapped out.

8. Replace the drip tray and grounds coffee container. Close the

service door.

Cleaning the Milk Container

Each time a milk function is used, TURN MILK FROTH

ADJUSTMENT KNOB TO CLEAN TO START CLEANING appears

on the display and the milk frother lid must be cleaned.

1. Leave the milk container in the coffee maker. You do not need

to empty it.

2. Place a cup or other recipient under the frothed milk spout.

3. Turn the foam adjustment dial to CLEAN. CLEANING MILK

CONTAINER PLACE A CUP UNDER THE MILK OUTLET

appears on the display together with a bar which gradually

lls as cleaning proceeds. Cleaning will stop automatically.

4. Turn the dial back to a froth selection. Remove the milk

container and always clean the steam connection nozzle with

a sponge.

NOTES:

■ If a number of milk based drinks needs to be made, only

clean the milk container after preparing the last beverage. To

proceed with making the next beverages when the CLEAN

message is displayed, press

ESC

■ If the milk container does not get cleaned, the (clean milk

container icon) appears on the display as a reminder that the

milk container needs cleaning.

■ In some cases, to carry out the cleaning the appliance requires

a short time to heat up.

PUSH

A. Support

B. Pin

PUSH

CLEAN

A. Foam adjustment dial

B. Coffee spouts

C. Milk spout

D. Cup

TROUBLESHOOTING

First try the solutions suggested here. If you need further assistance or more recommendations that may help you avoid a service call,

refer to the warranty, or visit https://producthelp.jennair.com. In Canada, visit www.jennair.ca.

Please include a daytime phone number in your correspondence.

PROBLEM POSSIBLE CAUSE REMEDY

The coffee is not hot The cups have not been preheated. Heat the cups by rinsing them with hot water.

The infuser has cooled down because

2-3 minutes have elapsed since the last coffee

was made.

Before making coffee, heat the infuser by selecting

the Rinse function from the menu.

A low coffee temperature is set. Change the set temperature. See “Coffee

Temperature” in the “Settings” section.

The coffee is weak or not

creamy enough

The coffee is ground too coarsely. Turn the grinding adjustment dial one click

counterclockwise towards number one while the

coffee mill is in operation. Continue one click at a

time until coffee delivery is satisfactory. The effect can

only be noticed after delivering two coffees.

The blend of coffee is unsuitable. Use a blend of coffee specically for espresso coffee

machines.

The coffee is delivered

too slowly or at a drop at

a time

The coffee is ground too nely. Turn the grinding adjustment dial one click clockwise

towards number seven while the coffee mill is in

operation. Continue one click at a time until coffee

delivery is satisfactory. The effect can only be noticed

after delivering two coffees.

The appliance does not

come on

The main switch is not turned on. Press the main switch to ON.

The milk does not come

out of the milk spout

The lid of the milk container is dirty. Clean the milk container lid as described in the

"Cleaning the Milk Container" section.

The infuser cannot be

extracted

The appliance has not been turned off correctly.

Turn the appliance off by pressing the button.

The milk contains large

bubbles or spurts out of

the milk spout or there is

little froth

The milk is not cold enough or is not semi-

skimmed or skimmed.

Use fully skimmed or semi-skimmed milk at

refrigerator temperature 5°C (41°F). If results are still

not satisfactory, try changing brand of milk.

The froth adjustment dial is incorrectly adjusted. Adjust following the instructions in the "Adjusting the

Amount of Froth" section.

The milk container lid or froth adjustment dial is

dirty.

Clean the milk container lid and froth adjustment dial

as described in the "Cleaning the Milk Container"

section.

The hot water/steam connection nozzle is dirty. Clean the connection nozzle as described in the

"Cleaning the Hot Water/Steam Connection Nozzle"

section.

At the end of descaling,

the appliance requests a

third rinse

During the two rinse cycles, the water tank was

not lled to MAX level.

Follow the instructions displayed by the appliance,

rst emptying the drip tray to avoid the water

overowing.

The machine emits

noises or small puffs of

steam while not in use

The machine is ready for use, or has recently

been turned off, and condensate is dripping into

the vaporizer which is still hot.

This is part of normal operation. To limit this, empty

the drip tray.

In the U.S.A.:

JennAir Brand Home Appliances

Customer eXperience Center

553 Benson Road

Benton Harbor, MI 49022-2692

In Canada:

JennAir Brand Home Appliances

Customer eXperience Centre

200 – 6750 Century Ave.

Mississauga, Ontario L5N 0B7

Displayed Messages

DISPLAYED MESSAGE POSSIBLE CAUSE REMEDY

ADD PRE-GROUND

COFFEE, PRE-GROUND

MAXIMUM ONE

MEASURING CUP

The "Pre-ground coffee" function has been

selected, but without placing any pre-ground

coffee in the funnel.

Place pre-ground coffee in the funnel and repeat

delivery.

The funnel for pre-ground coffee is clogged. Empty the funnel using the brush provided as

described in the "Cleaning the Pre-Ground Coffee

Funnel" section.

A "Tall" coffee with pre-ground coffee has been

requested.

Place pre-ground coffee in the funnel and press

to continue and complete delivery.

EMPTY GROUND

CONTAINER

The grounds container is full. Empty the grounds container and drip tray, clean and

replace them.

IMPORTANT: When removing the drip tray, the

grounds container must always be emptied, even if it

contains a few grounds. If this is not done, when you

make the next coffees, the grounds container may ll

up more than expected and clog the machine.

DESCALING NEEDED,

PRESS OK TO START

(~45 MIN)

Indicates that descaling is needed.

Press

to start descaling or press

ESC

descale later. The descaling procedure described in

the "Descaling" section needs to be performed.

FILL BEAN CONTAINER The coffee beans have run out. Fill the beans container.

FILL WATER TANK WITH

FRESH WATER

The water tank is empty or incorrectly

positioned.

Fill the tank with fresh water and or insert it correctly

pushing it as far as it will go until it clicks into place.

ESC

PUSH

ESC

DISPLAYED MESSAGE POSSIBLE CAUSE REMEDY

GENERAL ALARM:

REFER TO USER

MANUAL

The inside of the coffee system is very dirty. Clean the inside of the appliance thoroughly, as

described in the "Cleaning" section. If the message

is still displayed after cleaning, contact an authorized

Customer Service Center.

SELECT A MILDER

TASTE OR REDUCE

PRE-GROUND COFFEE

QUANTITY

Too much coffee has been used.

Select a milder taste by pressing or reduce

the quantity of pre-ground coffee (maximum one

measure).

GROUND TOO FINE.

ADJUST GRIND

LEVEL 1 CLICK WHILE IN

OPERATION

The grinding is too ne and the coffee is

delivered too slowly or not at all.

Repeat coffee delivery and turn the grinding

adjustment dial one click clockwise towards number

seven while the coffee mill is in operation. If after

making at least two coffees delivery is still too slow,

repeat the correction procedure, turning the grinding

adjustment dial another click. If the problem persists,

make sure the water tank is fully inserted.

If the water lter is present, an air bubble

may have been released inside the circuit,

obstructing delivery.

Insert the hot water/steam spout in the appliance

and deliver a little fresh water until the ow becomes

regular.

INSERT BREWING

UNIT

After cleaning, the infuser has not been

replaced.

Insert the infuser as described in the "Cleaning the

Infuser" section.

INSERT MILK

CONTAINER

The milk container is not inserted correctly. Insert the milk container as far as it will go.

ESC

PUSH

DISPLAYED MESSAGE POSSIBLE CAUSE REMEDY

INSERT GROUND

CONTAINER AND DRIP

TRAY

After cleaning, the grounds container has not

been replaced.

Remove the drip tray and insert the grounds

container.

INSERT WATER OUTLET The hot water spout is not inserted or is inserted

incorrectly.

Insert the water spout as far as it will go.

WATER CIRCUIT EMPTY

PRESS OK TO START

FILLING PROCESS

The water circuit is empty.

Press

and allow fresh water to drain out of the

spout; the ow will stop itself automatically. If the

problem persists, make sure the water tank is fully

inserted.

PRESS OK TO START

CLEANING PROCESS OR

TURN MILK FROTH

ADJUSTMENT KNOB

The milk container has been inserted with the

froth adjustment dial in the CLEAN position.

To proceed with the CLEAN function, press

or turn the froth adjustment dial to one of the milk

positions.

PUSH

La page charge ...

JennAir JJB6424HM Le manuel du propriétaire

Marque: JennAir

Modèle: JJB6424HM

Catégorie: Accessoires de préparation de café

Taper: Le manuel du propriétaire

Ce manuel convient également à

JJB6424HL

Télécharger le PDF

rapport

dans d''autres langues

English: JennAir JJB6424HM Owner's manual

JennAir JJB6424HM Le manuel du propriétaire

Ce manuel convient également à

JennAir JJB6424HM Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents