Panoptix
™
PS22-TR
Installation Instructions
Important Safety Information
WARNING
See the Important Safety and Product Information guide in the
chartplotter or fishfinder product box for product warnings and
other important information.
You are responsible for the safe and prudent operation of your
vessel. Sonar is a tool that enhances your awareness of the
water beneath your boat. It does not relieve you of the
responsibility of observing the water around your boat as you
navigate.
CAUTION
Failure to install and maintain this equipment in accordance with
these instructions could result in damage or injury.
To obtain the best performance and to avoid damage to your
boat, you must install the Garmin
®
device according to these
instructions.
Read all installation instructions before proceeding with the
installation. If you experience difficulty during the installation, go
to support.garmin.com for more information.
Software Update
You may need to update the device software when you install
the device or add an accessory to the device.
This device supports up to a 32 GB memory card, formatted to
FAT32.
Loading the New Software on a Memory Card
You must copy the software update to a memory card using a
computer that is running Windows
®
software.
NOTE: You can contact Garmin support to order a preloaded
software update card if you do not have a computer with
Windows software.
1
Insert a memory card into the card slot on the computer.
2
Go to www.garmin.com/support/software/marine.html.
3
Select the software update bundle that corresponds to the
chartplotter to be updated.
NOTE: The software update bundle includes updates for all
devices connected to the chartplotter. You can select See All
Devices in this Bundle to confirm the devices included in the
download.
4
Select Download.
5
Read and agree to the terms.
6
Select Download.
7
Choose a location, and select Save.
8
Double-click the downloaded file.
9
Select Next.
10
Select the drive associated with the memory card, and select
Next > Finish.
A Garmin folder containing the software update is created on the
memory card. The software update can take several minutes to
load onto the memory card.
Updating the Device Software
Before you can update the software, you must obtain a
software-update memory card or load the latest software onto a
memory card.
1
Turn on the chartplotter.
2
After the home screen appears, insert the memory card into
the card slot.
NOTE: In order for the software update instructions to
appear, the device must be fully booted before the card is
inserted.
3
Follow the on-screen instructions.
4
Wait several minutes while the software update process
completes.
5
When prompted, leave the memory card in place and restart
the chartplotter manually.
6
Remove the memory card.
NOTE: If the memory card is removed before the device
restarts fully, the software update is not complete.
Registering Your Device
Help us better support you by completing our online registration
today.
• Go to my.garmin.com/registration.
• Keep the original sales receipt, or a photocopy, in a safe
place.
Tools Needed
• #2 Phillips screwdriver
• 3 mm flat screwdriver
Mounting Considerations
• Placement of the transducer on a trolling motor depends on
the type of trolling motor you have installed on your boat.
• You should consider the operation modes before selecting a
mounting location. Mounting the transducer on the trolling
motor shaft is recommended for LiveVü Forward mode.
Mounting the transducer on the trolling motor is
recommended for LiveVü Down mode, or if you plan to switch
between the forward and down modes.
• You must angle the transducer correctly for each mode to
work properly (Adjusting the Transducer Angle, page 3).
• You can mount the transducer on the motor of some
electrically steered trolling motors, but you must make sure
you can safely deploy and retract the trolling motor with the
transducer attached.
• You must mount the transducer so it does not obstruct the
motor from being placed in its storage cradle or prevent the
motor from being stowed and deployed correctly.
• Do not mount the transducer near strong magnetic fields,
which interfere with the ability of the internal compass to
measure the earth's magnetic field and prevent calibration.
Failure to properly calibrate causes some map features to be
unavailable, and waypoints created in LiveVü Forward mode
use the boat heading instead of the transducer orientation to
calculate your position.
• You must mount the transducer as far from the motor as
possible while keeping the transducer submerged. Placing
the transducer on the barrel of the trolling motor or too close
July 2017
190-02269-02_0A
to the motor on the shaft, can prevent proper compass
calibration.
• To use the compass, you must mount the transducer on the
shaft. The compass does not work when you mount the
transducer on the motor.
Effective Forward and Down Range
CAUTION
Water conditions and bottom conditions affect the depth and
range performance of the transducer. You should use caution
and observe the water depth and range, especially when your
unit is operating in manual range or depth mode.
When operating in LiveVü Forward mode, the transducer has an
effective forward range of between five and eight times the
depth of the water. For example, in 3 m (10 ft.) of water, the
effective forward range is between 15 and 24 m (between 50
and 80 ft.). Water conditions and bottom conditions affect the
actual range. You should use caution and observe the water
depth and forward range, especially when your device is in
manual forward range mode.
When operating in LiveVü Down mode, the fore/aft range is
equal to the depth of the water. For example, in 10 m (33 ft.)
water depth, the screen will display 5 m (16 ft.) fore and 5 m
(16 ft.) aft of the transducer. Deeper water provides a greater
fore and aft range.
Trolling Motor Shaft Installation
This is the preferred mounting method for the LiveVü Forward
mode. This method provides maximum separation between the
motor and transducer, enabling optimum performance of the
magnetic compass function.
This is not the recommended method for the LiveVü Down
mode. The trolling motor barrel could block the sonar beam.
Assembling the Trolling Motor Shaft Mount Hardware
Use the M6 screws
À
to attach the back of the trolling mount
bracket
Á
to the front of the trolling mount bracket
Â
around
the trolling motor shaft.
Installing the Transducer on the Trolling Motor Shaft
Mount
NOTICE
You must secure the transducer cable to the shaft or other
secure location during installation. Damage to the transducer
cable wire or the cable jacket can cause transducer failure.
You should mount the transducer as far from the motor as
possible. Placing the transducer too close to the motor can
prevent proper compass calibration. Without successful
compass calibration, the chartplotter does not display direction
and coverage area indicators, but all other features function
normally.
1
Use the enclosed knob
À
or mounting bolt to attach the
transducer
Á
to the trolling motor mount bracket
Â
.
2
Use cable ties to secure the transducer cable to the shaft or
other secure location.
3
Route the Ethernet cable to the network switch or to the back
of the chartplotter.
4
Route the power cable to a switched or unswitched
10-35 Vdc power source.
Trolling Motor Installation
This is the preferred mounting method for the LiveVü Down
mode, or if you plan to switch between the forward and down
modes. This method provides the maximum unobstructed view
of the sonar beam.
Because of the close proximity of transducer to the strong
magnetic fields from the trolling motor, the transducer's
magnetic compass feature might not calibrate properly, and you
might not be able to use that feature.
Assembling the Trolling Motor Mount Hardware
1
Insert the hose clamp
À
through the slot on the trolling motor
mount
Á
.
2
Slide the hose clamp around the trolling motor.
3
Tighten the hose clamp.
Installing the Transducer on a Trolling Motor
NOTICE
You must secure the transducer cable to the shaft or other
secure location during installation. Transducer cable wire
damage or damage to the cable jacket can cause transducer
failure.
1
Use the enclosed knob
À
or mounting bolt to attach the
transducer
Á
to the trolling motor mount bracket
Â
.
2
2
Use cable ties to secure the transducer cable to the shaft or
other secure location.
3
Route the Ethernet cable to the network switch or to the back
of the chartplotter.
4
Route the power cable through a switched or unswitched 10
to 35 Vdc power source.
Adjusting the Transducer Angle
The transducer should be angled properly for optimal imagery in
each mode.
1
With the transducer mounted, angle the transducer according
to the mode you will use:
• For LiveVü Forward mode, angle the transducer forward
and slightly downward.
• For LiveVü Down mode, angle the transducer down.
TIP: You may want to experiment to find the best angle for
your sonar needs.
2
Tighten the knob or mounting bolt so the device does not
move during use.
3
On the chartplotter, select Sonar, and select LiveVü Down
or LiveVü Forward.
Connecting the Transducer to Power and the
Garmin Marine Network
WARNING
When connecting the power cable, do not remove the in-line
fuse holder. To prevent the possibility of injury or product
damage caused by fire or overheating, the appropriate fuse
must be in place as indicated in the product specifications. In
addition, connecting the power cable without the appropriate
fuse in place voids the product warranty.
1
Route the cables using the appropriate tie wraps, fasteners,
and sealant to secure the cables along the route, and through
any bulkheads or the deck.
2
Connect the bare-wire end of the power cable to a 10 to
35 Vdc power source and to the groundInstallation Diagram,
page 3.
NOTE: A power switch is optional. The chartplotter
automatically turns the transducer on and off.
3
Select an option:
• Connect the network cable to the network or the Panoptix
port on your chartplotter.
• Connect the network cable to a port on the GMS
™
10, if
available.
Cable Routing Grommets
When routing cables through your boat, it may be necessary to
drill holes to route the cables. Cable routing grommets can be
used to cover cable installation holes. The grommets do not
create a waterproof seal. If necessary, apply a marine sealant
after installation to weatherproof around the grommet and the
cable. You can purchase grommets from your Garmin dealer or
directly from Garmin at www.garmin.com.
Installation Diagram
+
-
Item Description
À
Chartplotter
Á
Panoptix PS22-TR
Â
Power source (switch is optional)
Calibrating the Compass
Before you can calibrate the compass, the transducer must be
installed on the shaft far enough away from the trolling motor to
avoid magnetic interference, and deployed in the water.
Calibration must be of sufficient quality to enable the internal
compass.
NOTE: To use the compass, you must mount the transducer on
the shaft. The compass does not work when you mount the
transducer on the motor.
You can begin turning your boat before calibrating, but you must
fully rotate your boat 1.5 times during calibration.
1
From an applicable sonar view, select Menu > Sonar Setup
> Installation.
2
If necessary, select Use AHRS to turn on the AHRS sensor.
3
Select Calibrate Compass.
4
Follow the on-screen instructions.
3
Maintenance
Cleaning the Transducer
Aquatic fouling accumulates quickly and can reduce your
device's performance.
1
Remove the fouling with a soft cloth and mild detergent.
2
If the fouling is severe, use a scouring pad or putty knife to
remove growth.
3
Wipe the device dry.
Specifications
Specification Measurement
Dimensions (W x H x L) 32 x 118 x 96 mm (1.3 x 4.6 x 3.8 in.)
Transducer weight 380 g (0.84 lb.)
Total weight (transducer, mount,
and cable)
840 g (1.85 lb.)
Max. continuous power usage 8 W
Peak transmit power 48 W
Operating voltage From 10 to 35 Vdc
Operating temperature range* From 0 to 40°C (from 32 to 104°F)
Storage temperature range From -40 to 70°C (from -40 to 158°F)
Material ASA plastic
Maximum range** 91.4 m (300 ft.)
Frequency 417 kHz
Fuse rating 4.0 A mini 32 Vdc
* When the transducer is used out of the water, the transducer
monitors the internal temperature and suspends operation until
the temperature returns to the operating range.
**Dependent upon transducer placement, water salinity, bottom
type, and other water conditions.
© 2017 Garmin Ltd. or its subsidiaries
Garmin
®
and the Garmin logo are trademarks of Garmin Ltd. or its subsidiaries,
registered in the USA and other countries. Panoptix
™
is a trademark of Garmin Ltd. or its
subsidiaries. These trademarks may not be used without the express permission of
Garmin.
-
1
-
2
-
3
-
4
Garmin Panoptix PS22-TR Guide d'installation
- Taper
- Guide d'installation
- Ce manuel convient également à
dans d''autres langues
Documents connexes
-
Garmin Panoptix PS21-TR Guide d'installation
-
Garmin GT8HW-TM High Wide CHIRP akterspegelgivare eller trollingmotorgivare i plast (150240kHz, 250W) (8-polig) Guide d'installation
-
Garmin 69808IN Manuel utilisateur
-
Garmin GT34UHD Le manuel du propriétaire
-
Garmin Echo 150 Le manuel du propriétaire
-
Garmin Panoptix™ Ice Fishing Kit Mode d'emploi
-
-
-
-
Garmin echoMAP™ 73sv Guide d'installation