Garmin Panoptix™ PS22-TR Guide d'installation

Marque: Garmin

Modèle: Panoptix™ PS22-TR

Taper: Guide d'installation

Ce manuel convient également à

Panoptix PS22-TR

Panoptix

™

PS22-TR

Installation Instructions

Important Safety Information

WARNING

See the Important Safety and Product Information guide in the

chartplotter or fishfinder product box for product warnings and

other important information.

You are responsible for the safe and prudent operation of your

vessel. Sonar is a tool that enhances your awareness of the

water beneath your boat. It does not relieve you of the

responsibility of observing the water around your boat as you

navigate.

CAUTION

Failure to install and maintain this equipment in accordance with

these instructions could result in damage or injury.

To obtain the best performance and to avoid damage to your

boat, you must install the Garmin

device according to these

instructions.

Read all installation instructions before proceeding with the

installation. If you experience difficulty during the installation, go

to support.garmin.com for more information.

Software Update

You may need to update the device software when you install

the device or add an accessory to the device.

This device supports up to a 32 GB memory card, formatted to

FAT32.

Loading the New Software on a Memory Card

You must copy the software update to a memory card using a

computer that is running Windows

software.

NOTE: You can contact Garmin support to order a preloaded

software update card if you do not have a computer with

Windows software.

Insert a memory card into the card slot on the computer.

Go to www.garmin.com/support/software/marine.html.

Select the software update bundle that corresponds to the

chartplotter to be updated.

NOTE: The software update bundle includes updates for all

devices connected to the chartplotter. You can select See All

Devices in this Bundle to confirm the devices included in the

download.

Select Download.

Read and agree to the terms.

Select Download.

Choose a location, and select Save.

Double-click the downloaded file.

Select Next.

Select the drive associated with the memory card, and select

Next > Finish.

A Garmin folder containing the software update is created on the

memory card. The software update can take several minutes to

load onto the memory card.

Updating the Device Software

Before you can update the software, you must obtain a

software-update memory card or load the latest software onto a

memory card.

Turn on the chartplotter.

After the home screen appears, insert the memory card into

the card slot.

NOTE: In order for the software update instructions to

appear, the device must be fully booted before the card is

inserted.

Follow the on-screen instructions.

Wait several minutes while the software update process

completes.

When prompted, leave the memory card in place and restart

the chartplotter manually.

Remove the memory card.

NOTE: If the memory card is removed before the device

restarts fully, the software update is not complete.

Registering Your Device

Help us better support you by completing our online registration

today.

• Go to my.garmin.com/registration.

• Keep the original sales receipt, or a photocopy, in a safe

place.

Tools Needed

• #2 Phillips screwdriver

• 3 mm flat screwdriver

Mounting Considerations

• Placement of the transducer on a trolling motor depends on

the type of trolling motor you have installed on your boat.

• You should consider the operation modes before selecting a

mounting location. Mounting the transducer on the trolling

motor shaft is recommended for LiveVü Forward mode.

Mounting the transducer on the trolling motor is

recommended for LiveVü Down mode, or if you plan to switch

between the forward and down modes.

• You must angle the transducer correctly for each mode to

work properly (Adjusting the Transducer Angle, page 3).

• You can mount the transducer on the motor of some

electrically steered trolling motors, but you must make sure

you can safely deploy and retract the trolling motor with the

transducer attached.

• You must mount the transducer so it does not obstruct the

motor from being placed in its storage cradle or prevent the

motor from being stowed and deployed correctly.

• Do not mount the transducer near strong magnetic fields,

which interfere with the ability of the internal compass to

measure the earth's magnetic field and prevent calibration.

Failure to properly calibrate causes some map features to be

unavailable, and waypoints created in LiveVü Forward mode

use the boat heading instead of the transducer orientation to

calculate your position.

• You must mount the transducer as far from the motor as

possible while keeping the transducer submerged. Placing

the transducer on the barrel of the trolling motor or too close

July 2017

190-02269-02_0A

to the motor on the shaft, can prevent proper compass

calibration.

• To use the compass, you must mount the transducer on the

shaft. The compass does not work when you mount the

transducer on the motor.

Effective Forward and Down Range

CAUTION

Water conditions and bottom conditions affect the depth and

range performance of the transducer. You should use caution

and observe the water depth and range, especially when your

unit is operating in manual range or depth mode.

When operating in LiveVü Forward mode, the transducer has an

effective forward range of between five and eight times the

depth of the water. For example, in 3 m (10 ft.) of water, the

effective forward range is between 15 and 24 m (between 50

and 80 ft.). Water conditions and bottom conditions affect the

actual range. You should use caution and observe the water

depth and forward range, especially when your device is in

manual forward range mode.

When operating in LiveVü Down mode, the fore/aft range is

equal to the depth of the water. For example, in 10 m (33 ft.)

water depth, the screen will display 5 m (16 ft.) fore and 5 m

(16 ft.) aft of the transducer. Deeper water provides a greater

fore and aft range.

Trolling Motor Shaft Installation

This is the preferred mounting method for the LiveVü Forward

mode. This method provides maximum separation between the

motor and transducer, enabling optimum performance of the

magnetic compass function.

This is not the recommended method for the LiveVü Down

mode. The trolling motor barrel could block the sonar beam.

Assembling the Trolling Motor Shaft Mount Hardware

Use the M6 screws

to attach the back of the trolling mount

bracket

to the front of the trolling mount bracket

around

the trolling motor shaft.

Installing the Transducer on the Trolling Motor Shaft

Mount

NOTICE

You must secure the transducer cable to the shaft or other

secure location during installation. Damage to the transducer

cable wire or the cable jacket can cause transducer failure.

You should mount the transducer as far from the motor as

possible. Placing the transducer too close to the motor can

prevent proper compass calibration. Without successful

compass calibration, the chartplotter does not display direction

and coverage area indicators, but all other features function

normally.

Use the enclosed knob

or mounting bolt to attach the

transducer

to the trolling motor mount bracket

Use cable ties to secure the transducer cable to the shaft or

other secure location.

Route the Ethernet cable to the network switch or to the back

of the chartplotter.

Route the power cable to a switched or unswitched

10-35 Vdc power source.

Trolling Motor Installation

This is the preferred mounting method for the LiveVü Down

mode, or if you plan to switch between the forward and down

modes. This method provides the maximum unobstructed view

of the sonar beam.

Because of the close proximity of transducer to the strong

magnetic fields from the trolling motor, the transducer's

magnetic compass feature might not calibrate properly, and you

might not be able to use that feature.

Assembling the Trolling Motor Mount Hardware

Insert the hose clamp

through the slot on the trolling motor

mount

Slide the hose clamp around the trolling motor.

Tighten the hose clamp.

Installing the Transducer on a Trolling Motor

NOTICE

You must secure the transducer cable to the shaft or other

secure location during installation. Transducer cable wire

damage or damage to the cable jacket can cause transducer

failure.

Use the enclosed knob

or mounting bolt to attach the

transducer

to the trolling motor mount bracket

Use cable ties to secure the transducer cable to the shaft or

other secure location.

Route the Ethernet cable to the network switch or to the back

of the chartplotter.

Route the power cable through a switched or unswitched 10

to 35 Vdc power source.

Adjusting the Transducer Angle

The transducer should be angled properly for optimal imagery in

each mode.

With the transducer mounted, angle the transducer according

to the mode you will use:

• For LiveVü Forward mode, angle the transducer forward

and slightly downward.

• For LiveVü Down mode, angle the transducer down.

TIP: You may want to experiment to find the best angle for

your sonar needs.

Tighten the knob or mounting bolt so the device does not

move during use.

On the chartplotter, select Sonar, and select LiveVü Down

or LiveVü Forward.

Connecting the Transducer to Power and the

Garmin Marine Network

WARNING

When connecting the power cable, do not remove the in-line

fuse holder. To prevent the possibility of injury or product

damage caused by fire or overheating, the appropriate fuse

must be in place as indicated in the product specifications. In

addition, connecting the power cable without the appropriate

fuse in place voids the product warranty.

Route the cables using the appropriate tie wraps, fasteners,

and sealant to secure the cables along the route, and through

any bulkheads or the deck.

Connect the bare-wire end of the power cable to a 10 to

35 Vdc power source and to the groundInstallation Diagram,

page 3.

NOTE: A power switch is optional. The chartplotter

automatically turns the transducer on and off.

Select an option:

• Connect the network cable to the network or the Panoptix

port on your chartplotter.

• Connect the network cable to a port on the GMS

™

10, if

available.

Cable Routing Grommets

When routing cables through your boat, it may be necessary to

drill holes to route the cables. Cable routing grommets can be

used to cover cable installation holes. The grommets do not

create a waterproof seal. If necessary, apply a marine sealant

after installation to weatherproof around the grommet and the

cable. You can purchase grommets from your Garmin dealer or

directly from Garmin at www.garmin.com.

Installation Diagram

Item Description

Chartplotter

Panoptix PS22-TR

Power source (switch is optional)

Calibrating the Compass

Before you can calibrate the compass, the transducer must be

installed on the shaft far enough away from the trolling motor to

avoid magnetic interference, and deployed in the water.

Calibration must be of sufficient quality to enable the internal

compass.

NOTE: To use the compass, you must mount the transducer on

the shaft. The compass does not work when you mount the

transducer on the motor.

You can begin turning your boat before calibrating, but you must

fully rotate your boat 1.5 times during calibration.

From an applicable sonar view, select Menu > Sonar Setup

> Installation.

If necessary, select Use AHRS to turn on the AHRS sensor.

Select Calibrate Compass.

Follow the on-screen instructions.

Maintenance

Cleaning the Transducer

Aquatic fouling accumulates quickly and can reduce your

device's performance.

Remove the fouling with a soft cloth and mild detergent.

If the fouling is severe, use a scouring pad or putty knife to

remove growth.

Wipe the device dry.

Specifications

Specification Measurement

Dimensions (W x H x L) 32 x 118 x 96 mm (1.3 x 4.6 x 3.8 in.)

Transducer weight 380 g (0.84 lb.)

Total weight (transducer, mount,

and cable)

840 g (1.85 lb.)

Max. continuous power usage 8 W

Peak transmit power 48 W

Operating voltage From 10 to 35 Vdc

Operating temperature range* From 0 to 40°C (from 32 to 104°F)

Storage temperature range From -40 to 70°C (from -40 to 158°F)

Material ASA plastic

Maximum range** 91.4 m (300 ft.)

Frequency 417 kHz

Fuse rating 4.0 A mini 32 Vdc

* When the transducer is used out of the water, the transducer

monitors the internal temperature and suspends operation until

the temperature returns to the operating range.

**Dependent upon transducer placement, water salinity, bottom

type, and other water conditions.

Garmin

and the Garmin logo are trademarks of Garmin Ltd. or its subsidiaries,

registered in the USA and other countries. Panoptix

™

is a trademark of Garmin Ltd. or its

subsidiaries. These trademarks may not be used without the express permission of

Garmin.

Garmin Panoptix™ PS22-TR Guide d'installation

Marque: Garmin

Modèle: Panoptix™ PS22-TR

Taper: Guide d'installation

Ce manuel convient également à

Panoptix PS22-TR

Télécharger le PDF

rapport

dans d''autres langues

English: Garmin Panoptix™ PS22-TR Installation guide

Garmin Panoptix™ PS22-TR Guide d'installation

Ce manuel convient également à

Garmin Panoptix™ PS22-TR Guide d'installation

dans d''autres langues

Documents connexes

Autres documents