Invacare RPS350-1E Owner's Operating And Maintenance Manual

STAND UP LIFT - MODEL RPS350-1E

STANDLIFT - MODELL RPS350-1E

STALIFT - MODEL RPS350 -1E

STAND UP LIFT - MODELE RPS350-1E

STAND UP LIFT - MODELO RPS350 - 1E

OWNER'S OPERATING and MAINTENANCE MANUAL

BETRIEBS- UND WARTUNGSANLEITUNG FÜR BENUTZER

BEDIENINGS- EN ONDERHOUDSHANDLEIDING

MANUEL DE L’UTILISATEUR FONCTIONNEMENT ET ENTRETIEN

MANUAL DE USO PARA EL PROPIETARIO

Y MANUAL DE MANTENIMIENTO

2

S

P

E

C

I

A

L

N

O

T

E

S

MAINTENANCE

Maintenance MUST be performed ONLY by qualified personnel.

SPECIAL NOTES

SAVE THESE INSTRUCTIONS AND KEEP WITH STAND UP LIFT AT ALL TIMES.

WARNING notices as used in this manual apply to hazards or unsafe practices which

could result in serious bodily harm.

CAUTION notices as used in this manual apply to hazards or unsafe practices which

could result in minor personal injury or property damage.

NOTES highlight procedures and contain information which assist the operator in

understanding the information contained in this manual.

WARNING

DO NOT OPERATE THIS EQUIPMENT WITHOUT FIRST READING AND

UNDERSTANDING THE WARNINGS, CAUTIONS AND INSTRUCTIONS IN

THIS MANUAL AND THE OWNER’S MANUAL PROVIDED WITH THE SLINGS.

IF YOU ARE UNABLE TO UNDERSTAND THE WARNINGS, CAUTIONS, AND

INSTRUCTIONS, CONTACT A HEALTHCARE PROFESSIONAL, DEALER OR

TECHNICAL PERSONNEL IF APPLICABLE BEFORE ATTEMPTING TO USE THIS

EQUIPMENT - OTHERWISE INJURY OR DAMAGE MAY RESULT.

RADIO FREQUENCY INTERFERENCE

Most electronic equipment is influenced by Radio Frequency Interference (RFI). CAU-

TION should be exercised with regard to the use of portable communication equip-

ment in the area around such equipment. If RFI causes erratic behavior, PUSH the Red

Emergency Stop Button IMMEDIATELY. DO NOT turn the Red Emergency Stop Button OFF

while transmission is in progress.

This product meets EN60601-1-2 Collateral Standard: Electromagnetic Compatibility.

"ATTENTION, see instructions for

use".

"Date of Manufacture"

SYMBOL LEGEND

WARNING - ALWAYS be aware of

the Lift Arms. Injury to the patient

and/or assistant may occur.

Device contains NiCd batteries. DO NOT dis-

pose of device or batteries in normal house-

hold waste. They MUST be taken to a proper

disposal site. Contact your local waste man-

agement company for information.

WARNING - ALWAYS be

aware of the Footrest,

especially the patient’s

position on the footrest.

Injury to the patient

and/or assistant may

occur.

3

SPECIAL NOTES ..................................................................................................................................2

SAFETY SUMMARY ..............................................................................................................................4

SPECIFICATIONS ..................................................................................................................................6

ASSEMBLY ............................................................................................................................................6

ATTACHING MAST TO BASE ...............................................................................................................6

ATTACHING ELECTRIC ACTUATOR TO MAST ...................................................................................6

OPERATION ..........................................................................................................................................7

OPERATING THE STAND UP LIFT ......................................................................................................7

Closing/Opening Legs of the Base......................................................................................................7

Locking/Unlocking the Rear Swivel Casters .......................................................................................7

Raising/Lowering Stand Up Lift ..........................................................................................................8

MOUNTING BATTERY CHARGER .......................................................................................................8

CHARGING BATTERIES ......................................................................................................................8

LIFTING PREPARATION ......................................................................................................................9

TRANSFERRING FROM .....................................................................................................................10

LIFTING THE PATIENT .......................................................................................................................10

MOVING THE PATIENT ...................................................................................................................... 11

TRANSFERRING TO ..........................................................................................................................12

TRANSFERRING THE PATIENT TO A WHEELCHAIR .......................................................................12

TRANSFERRING THE PATIENT TO A BED .......................................................................................13

TRANSFERRING THE PATIENT TO A COMMODE ............................................................................14

MAINTENANCE SAFETY INSPECTION CHECKLIST .......................................................................15

TROUBLESHOOTING ........................................................................................................................16

CARE AND MAINTENANCE OF YOUR STAND UP LIFT ...................................................................17

LUBRICATION ....................................................................................................................................17

WEAR AND DAMAGE ........................................................................................................................17

CLEANING .........................................................................................................................................17

ADJUSTING THE BASE .....................................................................................................................17

REPLACING THE KNEE PAD ............................................................................................................18

REPLACING OPTIONAL LEG STRAP ...............................................................................................18

REPLACING THE PADDED COVER .................................................................................................18

REPLACING ELECTRIC ACTUATOR ................................................................................................18

REPLACING CASTERS AND/OR FORKS .........................................................................................19

LIMITED WARRANTY ..........................................................................................................................20

BETRIEBS- UND WARTUNGSANLEITUNG FÜR BENUTZER ......................... 22

BEDIENINGS- EN ONDERHOUDSHANDLEIDING............................................ 42

MANUEL DE L’UTILISATEUR FONCTIONNEMENT ET ENTRETIEN ............... 62

MANUEL DE USO PARA EL PROPIETARIO Y MANUAL

DE MANTENIMIENTO ...................................................................................... 82

T

A

B

L

E

O

F

C

O

N

T

E

N

T

S

TABLE OF CONTENTS

4

SAFETY SUMMARY

S

A

F

E

T

Y

S

U

M

A

R

Y

NOTE: Check all parts for shipping damage before using. In case of damage, DO NOT use the equipment.

Contact the Carrier/Dealer for further instructions.

WARNING

Invacare recommends that two (2) assistants be used for ALL lifting preparation, transferring from

and transferring to procedures.

DO NOT attempt any transfer without approval of the patient’s physician, nurse or medical assis-

tant. Thoroughly read the instructions in this Owner’s Manual, observe a trained team of experts

perform the lifting procedures and then perform the entire lift procedure several times with proper

supervision and a capable individual acting as a patient.

Individuals that use the Standing Sling (Model R130) MUST be able to support the majority of their

own weight, otherwise injury can occur.

DO NOT raise the patient to a full standing position while using the transport sling (Model

R134), otherwise injury can occur.

Invacare standing and transport slings are specifically designed to be used in conjunction with

the Invacare Stand Up Lift. Slings and accessories designed by other manufacturers or other

Invacare slings are not to be utilized as a component of Invacare’s stand up lift system. Use of

these products is prohibited and will void Invacare’s stand up lift warranty. Use only genuine

Invacare standing and transport slings and lift accessories to maintain patient safety and prod-

uct utility. Use the sling that is recommended by the individual’s doctor, nurse or medical assistant

for the comfort and safety of the individual being lifted.

Before positioning the legs of the stand up lift around the patient, make sure the patient's feet are

out of the way of the footplate, otherwise injury can occur.

The legs of the stand up lift MUST be in the MAXIMUM OPEN position and the shifter handle LOCKED

in place for optimum stability and safety. If the patient is in a transport sling and it becomes

necessary to move through a narrow passage, close the legs of the stand up lift ONLY AS LONG

AS IT TAKES TO MOVE THROUGH THE PASSAGE. Once the stand up lift is through the passage, return

the legs of the stand up lift to the MAXIMUM OPEN position and LOCK shifter handle IMMEDIATELY.

Invacare recommends locking the rear swivel casters ONLY when positioning or removing the

sling (standing or transport) from around the patient.

Invacare does NOT recommend locking the rear swivel casters of the stand up lift when lifting

and transferring an individual. Doing so could cause the lift to tip and endanger the patient and

assistants. Invacare DOES recommend that the rear swivel casters be left UNLOCKED during lifting

and transferring procedures to allow the stand up lift to stabilize itself when the patient is initially

lifted from and transferred to a chair, bed or any stationary object.

STANDING SLINGS - DO NOT use the standing sling in combination with the stand up lift as a

transport device. It is intended to transfer an individual from one resting surface to another (such

as a bed to a wheelchair). Moving a person using the standing sling in combination with the

stand up lift over ANY distance is NOT recommended.

STANDING SLINGS - Before lifting the patient, make sure the bottom edge of the standing sling is

positioned on the lower back of the patient and the patient's arms are outside the standing sling.

STANDING SLINGS - The belt MUST be snug, but comfortable on the patient, otherwise the patient

can slide out of the sling during transfer, possibly causing injury.

TRANSPORT SLINGS - Before lifting the patient, make sure the bottom edge of the transport sling is

at the base of the spine and the patient's arms are outside the transport sling.

5

SAFETY SUMMARY, (continued)

SAFETY SUMMARY

S

A

F

E

T

Y

S

U

M

A

R

Y

WARNING

DO NOT use any kind of material (such as a plastic back incontinence pad or seating cushion)

between the patient and sling material that may cause the patient to slide out of the sling during

transferring.

ALWAYS use the color coded strap on the standing sling closest to the patient while still maintain-

ing patient stability and comfort.

Bleached, torn, cut, frayed, or broken slings are unsafe and could result in injury. Discard Immedi-

ately.

DO NOT alter slings.

When elevated a few inches off the surface being transferred from and before moving the pa-

tient, check again to make sure that the sling is properly connected to the attachment points of

the stand up lift. If any attachments are NOT properly in place, lower the patient back onto the

surface and correct this problem.

During transfer, with patient suspended in a sling attached to the lift, DO NOT roll stand up lift over

objects such as carpet, raised carpet bindings, door frames, or any uneven surfaces or obstacles

that would create an imbalance of the stand up lift and could cause the stand up lift to tip over.

Use push handle on the mast at ALL times to push or pull the stand up lift.

Casters and axle bolts require inspection every six (6) months to check for tightness and wear.

After the first 12 months of operation, inspect all pivot points and fasteners for wear. If the metal is

worn, the parts MUST be replaced. Make this inspection every three (3) months thereafter.

The electric motor is sealed at the factory and if service is required, the motor unit MUST BE re-

turned to the factory for repair. DO NOT attempt to open the motor or obtain local service as this

will VOID the warranty and may result in damage and a costly repair. Consult your Dealer or

Invacare for further information.

Regular maintenance of Stand Up Lift and accessories is necessary to assure proper operation.

GROUNDING INSTRUCTIONS:

DO NOT, under any circumstances, cut or remove the round grounding prong from any plug used with

or for Invacare products. Some devices are equipped with three-prong (grounding) plugs for protec-

tion against possible shock hazards. Where a two-prong wall receptacle is encountered, it is the per-

sonal responsibility and obligation of the customer to contact a qualified electrician and have the

two-prong receptacle replaced with a properly grounded three-prong wall receptacle in accor-

dance with the National Electrical Code. If you must use an extension cord, use ONLY a three-wire

extension cord having the same or higher electrical rating as the device being connected. In addi-

tion, Invacare has placed RED/ORANGE WARNING TAGS on some equipment. DO NOT remove these

tags. Carefully read battery/battery charger information prior to operating, charging or servicing your

stand up lift.

WEIGHT LIMITATION

DO NOT exceed maximum weight limitation of the Stand Up Lift. The maximum weight limitation

is 350 lbs. (159 kg) regardless of any additional weight limitations on accessories.

6

Height at Sling Hook-

up Knob MAXIMUM:

Height at Sling Hook-

up Knob MINIMUM:

Base Width OPEN:

Base Width CLOSED:

Base Height

(Clearance):

Base Length:

Overall Height:

Overall Length:

Overall Width:

Caster Size FRONT:

Caster Size LOCKING

REAR:

Sling Options:

Sling Material:

Weight Capacity:

Weight:

Battery:

Charger Input:

Charger Output:

Charging Time:

Audio Low Battery

Alarm:

Motor Safety Devices:

* Approx. Lifts per

Charge:

Warranty (Electric/

Electronics):

Emergengcy Stop

Button:

168 cm

102 cm

94 cm

66 cm

12 cm

90 cm

124.5 cm

99 cm

65.5 cm

7.6 cm

12.7 cm

Standing or Transport (See

below for details)

Polyester

159 Kg

52.2 Kg

24 VDC (RECHARGEABLE)

100 - 240 VAC

29.5 VDC

Maximum 6 Hours

YES

Anti-Entrapment

*100-200 Cycles per

Charge

1 Year

YES

SPECIFICATIONS/ASSEMBLY

SPECIFICATIONS

S

P

E

C

I

F

I

C

A

T

I

O

N

S

Stand Up Lift

* Varies dependent upon load and stroke.

FIGURE 1 - ATTACHING MAST TO BASE

ATTACHING MAST TO BASE

(FIGURE 1)

1. Lock the rear swivel casters. Refer to LOCKING/

UNLOCKING THE REAR SWIVEL CASTERS in

this section of the manual.

2. Remove the hex bolt, nut and washer, that are lo-

cated in the U-shape cut-out of the base.

3. Position the mast in an upright position and place the

mast onto the U-shaped cut-out of the base.

4. Insert hex bolt with washers through the base and

mast. Secure with nut.

WARNING

The mast may be removed from the base

for storage or transporting. Each time mast

is removed and returned to base, the mast

MUST be properly secured to the base.

ATTACHING ELECTRIC ACTUATOR

TO MAST (FIGURE 2)

1. Remove the top nut, top bolt, bracket and bushing

from the lift arm mounting bracket.

2. Position the electric actuator in the lift arm mounting

bracket as shown in FIGURE 2.

3. Reinstall top nut, top bolt, bracket and bushing into lift

arm mounting bracket and electric actuator. Tighten se-

curely.

CAUTION

DO NOT overtighten mounting hardware.

This will damage mounting brackets.

Mast

U-Shaped

Cut-out

Hex Bolt

Nut

Washer

ASSEMBLY

A

S

E

M

B

L

Y

PATIENT SLINGS: STANDING TRANSPORT

Width 91.4 cm 97.8 cm

Length 33 cm 91.4 cm

7

OPERATION

OPENING

CLOSING

FIGURE 1- CLOSING/OPENING LEGS OF

BASE

OPERATING THE STAND UP LIFT

Closing/Opening Legs of Base (FIGURE 1)

The shifter handle is used to open or close the legs of the

base for stability when lifting a patient.

1. Stand at the rear of the stand up lift and grasp the

shifter handle with one (1) hand and place the oppo-

site hand on the push handle of the mast for balance.

NOTE: The shifter handle MUST lock into its mount-

ing slot to lock legs in the full open or closed position.

Legs of Base

Mounting Slot

Shifter Handle in Locked

CLOSED Position

Legs of

Base

Mounting

Slot

Shifter Handle in Locked

OPENED Position

O

P

E

R

A

T

I

O

N

OPERATION

FIGURE 2 - ATTACHING ELECTRIC ACTUATOR TO MAST

CLOSING.

1. Pull the shifter handle OUT and away from the

stand up lift and then to your LEFT until it LOCKS in

the notch of the bracket.

NOTE: Left is determined by standing behind the stand

up lift facing towards the front casters.

OPENING.

1. Pull the shifter handle OUT and away from the

stand up lift and then to your RIGHT until it LOCKS in

the notch of the bracket.

NOTE: Right is determined by standing behind the

stand up lift facing towards the front casters.

Locking/Unlocking the Rear Swivel

Casters (FIGURE 2)

1. Perform one (1) of the following:

A. LOCKING - Press DOWN on the BOTTOM of

the locking lever.

B. UNLOCKING - Press DOWN on the TOP of the

locking lever.

FIGURE 2 - LOCKING/UNLOCKING THE

REAR SWIVEL CASTERS

STEP HERE TO LOCK STEP HERE TO UNLOCK

Locking

Lever

Lift Arm

Mounting

Bracket

Electric

Actuator

Top Nut

Top

Bolt

Bushing

Bracket

8

O

P

E

R

A

T

I

O

N

OPERATION

FIGURE 3 - RAISING/LOWERING

STAND UP LIFT

Control

Box

Red Emergency Stop Button

MOUNTING BATTERY CHARGER

(FIGURE 4)

NOTE: Refer to your local regulations concerning proper

mounting procedures.

1. Place the battery charger with mounting bracket on

the wall at the desired position.

2. With a pencil, mark the MIDDLE hole position.

3. Measure down 16.5 cm from the pencil mark and drill

one (1) mounting hole.

FIGURE 4 - MOUNTING BATTERY CHARGER

Hand Control

UP Button

DOWN Button

Press IN to Stop

Lift Arms

Rotate CLOCKWISE to

Disengage Emergency Stop

BOTTOM

Mounting

Screw

(STEP 4)

Battery Charger with Mounting

Bracket (STEP 5)

Mounting

Screws

(STEP 7)

Mounting Bracket

(STEP 6)

CHARGING BATTERIES (FIGURE 5)

NOTE: Invacare recommends the battery be recharged

daily.

NOTE: An audible alarm will sound (horn will beep) when

battery is low.

1. Lift UP on the handle on the top of the battery.

2. Lift the battery UP and OUT away from control box.

WARNING

Make sure there is an audible click when

mounting battery on the battery charger

to confirm proper mounting. Otherwise,

injury or damage may occur. Refer to FIG-

URE 5 for correct mounting.

3. Place the battery on the battery charger as shown in

FIGURE 5. Make sure there is an audible click.

NOTE: The charge LED will illuminate.When charging is

complete, the charge LED will stop illuminating.

Raising/Lowering Stand Up Lift

(FIGURE 3)

RAISING THE LIFT. Press the UP (

ÏÏ

Ï) button on the

hand control to raise the lift arms and the patient.

LOWERING THE LIFT. Press the DOWN (

ÐÐ

Ð) button

on the hand control to lower the lift arms and the patient.

NOTE: If the Stand Up Lift is in the full UP position, it

may be necessary to pull down slightly on the lift arms

before the mast will lower.

EMERGENCY STOP. Press the RED button on the

control box IN to stop the lift arms and patient from raising

or lowering.

NOTE: Rotate RED emergency stop button CLOCK-

WISE until it pops out to disengage.

4. Install the BOTTOM mounting screw until there is an

approximate 3 mm gap between the screw head and

the wall.

5. Install the battery charger with mounting bracket

onto the bottom mounting screw.

6. Drill the remaining two (2) mounting holes.

7. Install the two (2) remaining mounting screws

through the mounting bracket and into the wall.

Tighten securely.

8. Plug battery charger into the wall electrical outlet.

NOTE: ON LED should illuminate.

9

FIGURE 5 - CHARGING BATTERIES

O

P

E

R

A

T

I

O

N

OPERATION

LIFTING PREPARATION

Refer to the patient sling Owner’s Manual, 1023891

for complete lifting preparation information.

Battery

Handle

(STEPS

1, 2, 4

and 5)

Battery

Charger

(STEP 3)

Audible Click

(STEPS 3

and 6)

Control Box

(STEP 6)

NOTE: A battery needing to be fully recharged will take

approximately six (6) hours.

4. Lift UP on the handle on the top of the battery.

5. Lift the battery UP and OUT away from battery charger.

WARNING

Make sure there is an audible click when

mounting battery on the control box to

confirm proper mounting. Otherwise, in-

jury or damage may occur. Refer to FIG-

URE 5 for correct mounting.

6. Reinstall the battery onto the control box as shown in

FIGURE 5. Make sure there is an audible click.

10

TRANSFERRING FROM

T

R

A

N

S

F

E

R

I

N

G

F

R

O

M

TRANSFERRING FROM

B. Patient's feet are positioned on the footplate as

shown in STEP 2B of FIGURE 1.

C. The bottom edge of the:

Standing Sling is positioned on the lower back.

Transport Sling is at the base of the patient's spine.

D. The patient's arms are outside of the standing or

transport sling.

E. The rear casters are unlocked.

F. Make sure the legs are in the maximum open posi-

tion and the shifter handle is locked in place.

WARNING

When elevated a few inches off the sur-

face being transferred from and before

moving the patient, check again to make

sure that the sling is properly connected

to the attachment points of the stand up

lift. If any attachments are NOT properly

in place, lower the patient back onto the

surface and correct this problem.

Adjustments for safety and comfort should

be made before moving the patient.

Invacare standing and transport slings are

specifically designed to be used in con-

junction with the Invacare Stand Up Lift.

Slings and accessories designed by other

manufacturers or other Invacare slings

are not to be utilized as a component of

Invacare’s stand up lift system. Use of

these products is prohibited and will void

Invacare’s stand up lift warranty. Use only

genuine Invacare standing and transport

slings and lift accessories to maintain pa-

tient safety and product utility.

If transferring from a wheelchair: Wheel-

chair wheel locks MUST be in the locked

position BEFORE lowering the patient into

the wheelchair.

3. Transferring from a wheelchair - Lock the wheel locks

of the wheelchair.

4. Press the UP (

Ï) button to raise the patient above

the surface (bed, wheelchair or commode) being

transferred from. The patient should be elevated just

high enough to clear the surface with their weight fully

supported by the lift.

NOTE: The lower center of gravity provides stability mak-

ing the patient feel more secure and the lift easier to move.

WARNING

Invacare recommends that two (2) assis-

tants be used for ALL lifting preparation,

transferring from and transferring to pro-

cedures.

LIFTING THE PATIENT (FIGURE 1)

1. Instruct the patient to do the following:

A. Hold onto the hand grips on both sides of the stand

up lift.

B. Lean back into the standing or transport sling.

WARNING

STANDING SLINGS - Before lifting the pa-

tient, make sure the bottom edge of the

standing sling is positioned on the lower

back of the patient and the patient's arms

are outside the standing sling.

TRANSPORT SLINGS - Before lifting the pa-

tient, make sure the bottom edge of the

transport sling is at the base of the spine

and the patient's arms are outside the

transport sling.

Invacare does NOT recommend locking

the rear casters of the stand up lift when

lifting and transferring an individual. Do-

ing so could cause the lift to tip and en-

danger the patient and assistants. Invac-

are DOES recommend that the rear cast-

ers be left UNLOCKED during lifting and

transferring procedures to allow the stand

up lift to stabilize itself when the patient is

initially lifted from and transferred to a

chair, bed or any stationary object.

The legs of the stand up lift MUST be in the

MAXIMUM OPEN position and the shifter

handle LOCKED in place for optimum sta-

bility and safety. If the patient is in a trans-

port sling and it becomes necessary to

move through a narrow passage, close

the legs of the stand up lift ONLY AS LONG

AS IT TAKES TO MOVE THROUGH THE PAS-

SAGE. Once the stand up lift is through

the passage, return the legs of the stand

up lift to the MAXIMUM OPEN position and

LOCK shifter handle IMMEDIATELY.

2. Make sure of the following:

A. Patient's knees are secure against the knee pad.

11

FIGURE 2 - MOVING THE PATIENT

MOVING THE PATIENT (FIGURE 2)

WARNING

STANDING SLINGS - DO NOT use the stand-

ing sling in combination with the stand up

lift as a transport device. It is intended to

transfer an individual from one resting sur-

face to another (such as a bed to a

wheelchair). Moving a person using the

standing sling in combination with the

stand up lift over ANY distance is NOT rec-

ommended.

During transfer, with patient suspended in

a sling attached to the lift, DO NOT roll

stand up lift over objects such as carpet,

raised carpet bindings, door frames, or

any uneven surfaces or obstacles that

would create an imbalance of the stand

up lift and could cause the stand up lift to

tip over. Use push handle on the mast at

ALL times to push or pull the stand up lift.

1. Using the push handle, move the stand up lift away

from the surface.

WARNING

The legs of the stand up lift MUST be in the

MAXIMUM OPEN position and the shifter

handle LOCKED in place for optimum sta-

bility and safety. If the patient is in a trans-

port sling and it becomes necessary to

move through a narrow passage, close

the legs of the stand up lift ONLY AS LONG

AS IT TAKES TO MOVE THROUGH THE PAS-

SAGE. Once the stand up lift is through

the passage, return the legs of the stand

up lift to the MAXIMUM OPEN position and

LOCK shifter handle IMMEDIATELY.

2. SLOWLY, move the patient to the desired surface.

3. Lower the patient onto the desired surface. Refer to

TRANSFERRING TO in this manual.

STEP 1

FIGURE 1 - LIFTING THE PATIENT

STEP 1A

STEP 1B

STEP 3

STEP 4

STEP

2A

STEP

2B

STEP

2C

STEP

2D

STEP

2E

NOTE: The lift arms will stay in position until the DOWN

(

ÐÐ

Ð) button is pressed.

5. Move the patient to the desired surface. Refer to

MOVING THE PATIENT in this section of the

manual.

TRANSFERRING FROM

T

R

A

N

S

F

E

R

I

N

G

F

R

O

M

12

TRANSFERRING TO

T

R

A

N

S

F

E

R

I

N

G

T

O

TRANSFERRING TO

FIGURE 1 - TRANSFERRING THE PATIENT TO A

WHEELCHAIR

WARNING

Invacare recommends that two (2) as-

sistants be used for ALL lifting prepara-

tion, transferring from and transferring

to procedures.

TRANSFERRING THE PATIENT TO

A WHEELCHAIR (FIGURE 1)

1. Move the wheelchair into position.

WARNING

Wheelchair wheel locks MUST be in the

locked position BEFORE lowering the pa-

tient into the wheelchair.

2. Lock the rear wheels of the wheelchair.

3. Position the patient over the wheelchair.

4. Press the DOWN (

Ð) button and lower the pa-

tient into the wheelchair.

WARNING

Invacare recommends locking the rear

swivel casters ONLY when positioning or

removing the sling (standing or transport)

from around the patient.

5. Lock the rear swivel casters. Refer to LOCKING/

UNLOCKING THE REAR SWIVEL CASTERS in

the OPERATION section of this manual.

6. Unhook the standing or transport sling from all at-

tachment points on the stand up lift.

7. If equipped, unfasten the leg strap from around the

patient's legs.

8. Instruct the patient to lift their feet off of the footplate.

NOTE: Assist the patient if necessary.

9. Remove the standing or transport sling from

around the patient.

10. Pull the stand up lift away from the wheelchair.

STEP 2

STEP 1

STEP 4

STEP 6

13

FIGURE 2 - TRANSFERRING THE PATIENT TO

A BED

TRANSFERRING THE PATIENT TO

A BED (FIGURE 2)

NOTE: The lower center of gravity provides stability

making the patient feel more secure and the lift easier

to move.

NOTE: The lift arms will stay in position until the DOWN

(

ÐÐ

Ð) button is pressed.

1. Position the patient as far over the bed as pos-

sible.

NOTE: If patient is being transferred from a surface

that is lower than the bed, press the UP (

ÏÏ

Ï) button to

raise the patient above the surface of the bed. The

patient should be elevated just high enough to clear

the bed with their weight fully supported by the lift.

2. Press the DOWN (

Ð) button and lower the pa-

tient onto the bed.

WARNING

Invacare recommends locking the rear

swivel casters ONLY when positioning or

removing the sling (standing or transport)

from around the patient.

3. Lock the rear swivel casters. Refer to LOCKING/

UNLOCKING THE REAR SWIVEL CASTERS in

the OPERATION section of this manual.

4. Unhook the standing or transport sling from all at-

tachment points on the stand up lift.

5. If equipped, unfasten the leg strap from around the

patient's legs.

6. Instruct the patient to lift their feet off of the footplate.

NOTE: Assist the patient if necessary.

7. Remove the standing or transport sling from

around the patient.

8. Pull the stand up lift away from the bed.

STEPS 1 AND 2

STEP 4

TRANSFERRING TO

T

R

A

N

S

F

E

R

I

N

G

T

O

14

TRANSFERRING THE PATIENT TO

A COMMODE (FIGURE 3)

1. Position the patient over the commode.

2. Press the DOWN (

Ð) button and lower the patient

onto the commode.

WARNING

Invacare recommends locking the rear

swivel casters ONLY when positioning or

removing the sling (standing or transport)

from around the patient.

3. Lock the rear swivel casters. Refer to LOCKING/

UNLOCKING THE REAR SWIVEL CASTERS in

the OPERATION section of this manual.

4. Perform one (1) of the following:

A. Standing Sling (Model R130) -

● Unhook the standing sling from the attach-

ment points on the stand up lift.

B. Transport Slings (Model R134) -

● Unhook the transport sling from the bottom

attachment points on the stand up lift.

● Lift up on the patient's legs and remove the

thigh supports from underneath the patient.

● If desired, unhook the transport sling from the

top attachment points on the stand up lift.

NOTE: The patient can remain in the upper por-

tion of the transport sling while using the com-

mode.

5. If equipped, unfasten the leg strap from around the

patient's legs.

6. Instruct the patient to lift their feet off of the footplate.

NOTE: Assist the patient if necessary.

7. Remove the standing or transport sling from around

the patient.

8. Pull the stand up lift away from the commode.

9. Once the patient is ready to be transferred, refer to

the LIFTING PREPARATION section of this manual.

FIGURE 3 - TRANSFERRING THE PATIENT TO A

COMMODE

TRANSFERRING TO

T

R

A

N

S

F

E

R

I

N

G

T

O

STEP 1

STEP 3

STEPS 4 AND 5

15

THE CASTER BASE

z Inspect for missing hardware.

z Base opens/closes with ease.

z Inspect casters and axle bolts for tightness and wear.

z Inspect casters for smooth swivel and roll.

SHIFTER HANDLE

z Operates smoothly.

z Locks adjustable base whenever engaged.

THE MAST

z Mast MUST be securely assembled to lift arms.

z Inspect for bends or deflections.

THE LIFT ARMS AND LINKAGE

z Check all hardware and attachment points.

z Inspect for bends or deflections.

z Inspect bolted joints of lift arms for wear.

z Inspect to ensure that the lift arms are centered

between the base legs.

THE ELECTRIC ACTUATOR ASSEMBLY

z Check for wear or deterioration. (IF DAMAGED,

CONTACT DEALER).

z Cycle to ensure smooth quite operation.

CLEANING

z Whenever necessary.

SLINGS

z CHECK ALL SLING ATTACHMENTS each time it is

used to ensure proper connection and patient safety.

z Inspect sling material for wear.

z Inspect straps for wear.

MAINTENANCE SAFETY INSPECTION CHECKLIST

INITIALLYITEM INSPECT/ADJUST

MONTHLY

INSPECT/ADJUST

PERIODICALLY

X

I

N

S

P

E

C

T

I

O

N

C

H

E

C

K

L

I

S

T

MAINTENANCE SAFETY INSPECTION CHECKLIST

16

SYMPTOMS

FAULTS

SOLUTION

Mast/Base joint loose.

Tie - Rods are loose.

Fluff or debris in bearings.

Needs lubrication.

Hand-control or actuator con-

nector loose.

RED emergency stop button

pressed IN.

Batteries low.

Battery not connected properly to

control box.

Electric actuator in need of ser-

vice.

Lift arms require a minimum

weight load to lower from the

uppermost position.

Stand up lift feels loose.

Casters/Brakes noisy or stiff.

Noisy or dry sound from pivots.

Electric actuator fails to lift when

button is pressed.

Lift arms will not lower in uppermost

position.

TROUBLESHOOTING

T

R

O

U

B

L

E

S

H

O

T

I

N

G

TROUBLESHOOTING

NOTE: If problems are not remedied by the suggested means, please contact your Dealer or Invacare.

Tighten the bolt, washer and locknut that

secure the mast to the base.

Refer to BASE ADJUSTMENT in the

CARE AND MAINTENANCE section of

this manual.

Refer to CASTERS in the CARE AND

MAINTENANCE section of this manual.

Refer to LUBRICATION in the CARE AND

MAINTENANCE section of this manual.

Check connections.

Rotate RED emergency stop button

CLOCKWISE until it pops out.

Charge batteries. Refer to CHARGING

BATTERIES in the OPERATION section

of this manual.

Reconnect the battery to the control box.

Refer to CHARGING BATTERIES in the

OPERATION section of this manual.

Refer to ELECTRIC ACTUATOR

REPLACEMENT in the CARE AND

MAINTENANCE section of this manual.

Contact your Dealer.

Pull down slightly on the lift arms.

17

CARE AND MAINTENANCE OF YOUR STAND UP LIFT

NOTE: Follow the maintenance procedures described in

this manual to keep your stand up lift in continuous ser-

vice.

The Invacare Stand Up Lift is designed to provide a

maximum of safe, efficient and satisfactory service with

minimum care and maintenance.

All parts of the Invacare Stand Up Lift are made of the best

grades of steel, but metal to metal contact will wear after

considerable use.

There is no adjustment or maintenance of either the cast-

ers or brakes, other than cleaning, lubrication and check-

ing axle and swivel bolts for tightness. Remove all debris,

etc. from the wheel and swivel bearings. If any parts are

worn, replace these parts immediately.

If you question the safety of any part of the lift, contact your

Dealer immediately and advise him/her of your problem.

LUBRICATION (FIGURE 1)

The Invacare Stand Up Lift is designed for minimum

maintenance; however, a six (6) month check should

ensure continued safety and reliability.

Keep lift and slings clean and in good working order. Any

defect should be noted and reported to your dealer as

soon as possible.

The casters MUST swivel and roll smoothly. A light grease

(waterproof auto lubricant) may be applied to the ball

bearing swivel of the casters once a year. Apply more

frequently if the casters are exposed to extreme moist

conditions.

WEAR AND DAMAGE

It is important to inspect all stressed parts, such as slings

and any attachment point for slings for signs of cracking,

fraying, deformation or deterioration. Replace any defective

parts immediately and ensure that the lift is not used until

repairs are made.

CLEANING

The sling should be washed regularly in water

temperature of 180

o

F (82

o

C) and a biological solution. A

soft cloth, dampened with water and a small amount of

mild detergent, is all that is needed to clean the stand up

lift. The lift can be cleaned with non-abrasive cleaners.

ADJUSTING THE BASE (FIGURE 2)

NOTE: The base adjustment should not require any

attention other than:

1. Check the squareness of the legs when in the

CLOSED position.

2. Place a square on the inside of the legs and base to

determine the 90

o

alignment.

3. Adjust the linkage rods until 90

o

alignment is achieved.

C

A

R

E

-

M

A

I

N

T

E

N

A

N

C

E

CARE AND MAINTENANCE OF YOUR STAND UP LIFT

FIGURE 1 - LUBRICATION

Lubricate the Bearings in the Caster Swivels

Square

Linkage

Rod

Linkage Rods

FIGURE 2 - ADJUSTING THE BASE

18

REPLACING THE KNEE PAD

(FIGURE 3)

1. Remove the four (4) button screws and washers that

secure existing knee pad to the stand up lift.

2. Remove the existing knee pad from stand up lift.

3. Position the mounting holes in the new knee pad with

the mounting holes in the stand up lift.

4. Using the existing hardware, secure the new knee

pad to the stand up lift.

5. Position the mounting holes in the knee pad with the

mounting holes in the stand up lift.

6. Using the existing hardware, secure the knee pad and

new leg strap to the stand up lift.

REPLACING THE PADDED COVER

(FIGURE 5)

1. Pull fastening strips on the existing padded cover apart.

2. Remove the existing padded cover from the lift arm.

3. Position the new padded cover around the lift arm.

4. Secure fastening strips on the new padded cover to-

gether.

REPLACING OPTIONAL LEG

STRAP (FIGURE 4)

1. Remove TOP (2) button screws and washers that

secure knee pad and existing leg strap to stand up lift.

2. Loosen BOTTOM two (2) button screws and wash-

ers that secure knee pad and existing leg strap to

stand up lift.

3. Remove the existing leg strap from stand up lift.

4. Position the new leg strap between the four (4) mount-

ing holes as shown in FIGURE 4.

NOTE: Make sure there is equal amounts of leg strap on

either side of the stand up lift.

C

A

R

E

-

M

A

I

N

T

E

N

A

N

C

E

CARE AND MAINTENANCE OF YOUR STAND UP LIFT

REPLACING ELECTRIC

ACTUATOR (FIGURE 6)

1. Remove the bottom nut, washer and shoulder bolt

that secure the electric actuator to the mast mounting

bracket.

2. Rest the lift arm on your shoulder and remove the top

nut, bolt, bracket and bushing from the lift arm mount-

ing bracket.

3. Remove the electric actuator.

4. Reverse STEPS 1-3 for installation of the new elec-

tric actuator.

CAUTION

DO NOT overtighten mounting hardware.

This will damage mounting brackets.

FIGURE 3 - REPLACING THE KNEE PAD

Knee Pad

Button Screws

Washers

Stand Up Lift

FIGURE 4 - REPLACING OPTIONAL LEG

STRAP

Leg Strap

Knee Pad

Button Screw

Washer

Stand Up

Lift

FIGURE 5 - REPLACING THE PADDED COVER

Padded Cover

Lift Arm

Fastening Strips

19

C

A

R

E

-

M

A

I

N

T

E

N

A

N

C

E

CARE AND MAINTENANCE OF YOUR STAND UP LIFT

REPLACING CASTERS AND/OR

FORKS (FIGURE 7)

WARNING

Casters and axle bolts require inspection

every six (6) months to check for tight-

ness and wear.

Rear Caster

1. Place the stand up lift on its side.

2. Remove the bolt and locknut that secure the existing

rear caster to the fork.

NOTE: The bushing will fall out of the rear caster.

NOTE: Existing bushing will be reused. Examine and re-

place if worn.

3. Install new/existing bushing into the new rear caster.

4. Line up the mounting holes in the new rear caster and

the fork.

5. Install the bolt through the fork and new rear caster

and tighten securely with the locknut.

Front Casters

1. Place the stand up lift on its side.

2. Remove the bolt and locknut that secure the existing

front caster assembly to the fork.

NOTE: The front caster assembly consists of two (2) cast-

ers and a washer in between.

NOTE: The washer will fall out from between the two (2)

casters.

NOTE: Existing washer will be reused. Examine and re-

place if worn.

3. Position new/existing washer between the two (2) new

casters.

4. Line up the mounting holes in the new front caster

assembly and the fork.

5. Install the bolt through the fork and new front caster

assembly and tighten securely with the locknut.

Forks

1. Place the stand up lift on its side.

2. Remove the front or rear caster from the stand up lift.

Refer to REPLACING CASTERS in this section of

the manual.

3. Unscrew the existing fork from the base.

4. Install the new fork onto the base.

5. Install the front or rear caster onto the stand up lift.

Refer to REPLACING CASTERS in this section of

the manual.

FIGURE 7 - REPLACING CASTERS AND/OR

FORKS

REAR

FRONT

Bolt

Bushing

Rear

Caster

Locknut

Fork

Base

Front

Casters

Locknut

Fork

Bolt

Washer

Lift Arm Mounting Bracket

FIGURE 6 - REPLACING ELECTRIC ACTUATOR

Bottom Nut

Washer

Shoulder Bolt

Electric

Actuator

Top Nut

Top

Bolt

Bushing

Bracket

Mast Mounting Bracket

20

LIMITED WARRANTY

This warranty is extended only to the original purchaser of our products and does not affect

statutory rights.

Invacare UK / Invacare Service Representative warrants the products manufactured to be

free from defects in materials and workmanship for a period of three (3) years on the lift and one

(1) year on the slings and electric components from the date of purchase. If within such

warranty period the product shall be proven to Invacare UK’s / Invacare Service Representa-

tive reasonable satisfaction to be defective, it shall be repaired or replaced, at Invacare UK’s

/ Invacare Service Representative option; Invacare UK’s / Invacare Service Representative

sole obligation, and your exclusive remedy under this warranty being limited to such repair or

replacement.

For warranty service, please contact Invacare UK’s Service Department / Invacare Service

Representative during normal working hours. Upon receiving notice of an alleged defect in a

product, Invacare UK / Invacare Service Representative will issue a serialized return authoriza-

tion. The product shall then be returned to either Invacare plant or service center as specified

by Invacare UK / Invacare Service Representative. Defective component part(s) must be

returned for warranty inspection using the serial number as identification within thirty (30) days

of return authorization date. DO NOT return products to our factory without prior consent.

LIMITATIONS AND EXCLUSIONS: THE FOREGOING WARRANTY DOES NOT COVER NORMAL WEAR

AND TEAR AND SHALL NOT APPLY TO PRODUCTS SUBJECTED TO NEGLIGENCE, ACCIDENT,

IMPROPER OPERATION, MAINTENANCE OR STORAGE, COMMERCIAL OR INSTITUTIONAL USE,

PRODUCTS MODIFIED WITHOUT INVACARE’S EXPRESS WRITTEN CONSENT (INCLUDING, BUT NOT

LIMITED TO, MODIFICATION THROUGH THE USE OF UNAUTHORIZED PARTS OR ATTACHMENTS)

OR TO PRODUCTS DAMAGED BY REASON OF REPAIRS MADE TO ANY COMPONENT WITHOUT

THE SPECIFIC CONSENT OF INVACARE UK / INVACARE SERVICE REPRESENTATIVE.

LIMITED WARRANTY

L

I

M

I

T

E

D

W

A

R

A

N

T

Y

La page charge ...

Invacare RPS350-1E Owner's Operating And Maintenance Manual

Invacare RPS350-1E Owner's Operating And Maintenance Manual

dans d''autres langues

Documents connexes

Autres documents