Disney DDC9000-P Manuel utilisateur

Marque: Disney

Modèle: DDC9000-P

Taper: Manuel utilisateur

User’s Guide

Princess Digital Camera

DDC9000-P

FO LD

4.75” x 4.75”

Table of Contents....................................................................................1

Important Information..............................................................................2

FCC Information ................................................................................2

User Information................................................................................2

Location of Controls................................................................................4

Front ..................................................................................................4

Rear...................................................................................................4

Changing the Faceplate..........................................................................5

Getting Started........................................................................................6

Recharging the Battery......................................................................6

Checking the Battery Level ...............................................................6

Using the Necklace ...........................................................................7

Operation ................................................................................................8

Turning the Power On/Off .................................................................8

Taking A Single Picture......................................................................9

Setting the Self Timer Mode..............................................................9

Setting the Continuous Snapshot Picture Mode .............................10

Taking Three Continuous Pictures ..................................................10

To Delete the Last Picture or Last Continuous Pictures..................11

To Delete All Pictures ......................................................................12

Setting the Image Quality Mode......................................................12

Setting the Frequency Mode ...........................................................13

Reset Button....................................................................................13

Display.............................................................................................13

Computer Connection...........................................................................14

Installing the Camera Software .......................................................14

Uninstalling the Camera Software...................................................16

Uninstalling the Camera Driver ........... ...........................................16

Downloading Photos .......................................................................16

Using Your Camera as a Web Cam ................................................18

Capturing AVI Video Files................................................................18

Using Microsoft Netmeeting ............................................................19

NHJ Photo Manager Tour................................................................19

Troubleshooting Guide..........................................................................20

Specifications........................................................................................21

TABLE OF CONTENTS

DDC9000P.qxp 7/15/05 10:39 AM Page 1

FCC INFORMATION

FCC WARNING: This equipment meets the limits for a class B

digital device, pursuant to Part 15 of FCC rules. Only the cable

supplied with the camera should be used. Operation with other

cables is likely to result in interference to radio and TV reception

and could void the user’s authorization to operate this equipment.

This device complies with Part 15 of the FCC Rules. Operation is

subject to the following two conditions:

1) This device may not cause harmful interference.

2) This device must accept any interference received, including

interference that may cause undesired operation.

Changes or modifications not expressly approved by the manu-

facturer may void the user’s authority to operate this equipment.

USER INFORMATION

NOTE: This equipment has been tested and found to comply with

the limits for a class B digital device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy

and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning

the equipment on and off, the user is encouraged to try to correct

the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

I M P O R TANT INFORMAT I O N

DDC9000P.qxp 7/15/05 10:39 AM Page 2

Be sure to observe the following precautions when using the camera:

• This camera works best when used in bright lighting, such

as sunlight or a brightly lit room. Results in dimly lit areas

will vary.

• Never try to take pictures or use the built-in display when

operating a motor vehicle or while walking.

• Never attempt your own repairs. Always leave service to

authorized repair facilities.

• Keep the camera away from water and other liquids, and never

let it get wet. Never use when it is raining or snowing.

• Should foreign matter or water get into the unit, immediately

turn the power off and contact your local authorized service

center.

• Physical damage and malfunction of this unit can cause the

image data stored in its memory to be deleted. Be sure to

always keep backup copies of data by transferring to a

personal computer.

• In an environment with electrostatic discharge, the user may

have to reset the unit.

• Do not leave the camera in places subject to extremely high

temperatures, such as a sealed vehicle or in direct sunlight.

• Do not place the camera in unstable locations, such as a

sloping surface or unstable table where the camera may fall.

• Do not touch or press on the display or lens.

I M P O R TANT INFORMAT I O N

DDC9000P.qxp 7/15/05 10:39 AM Page 3

1. Compartment

Cover Flap (Side of

Unit)

2. LED Indicator

3. Camera’s Loop

4. Lens

5. Display

6. Reset Button

(Inside

Compartment)

7. Viewfinder

8. Compartment and

Faceplate

9. Mode/Power ON

Button

10. Shutter/Select

Button

11. USB Jack (Under

Compartment

Cover Flap)

L O C ATION OF CONTROLS

FRONT

REAR

DDC9000P.qxp 7/15/05 10:39 AM Page 4

CHANGING THE FACEPLATE

A Disney faceplate is included with this unit. To use your own picture,

follow the instructions below.

Place the template over the

desired photograph and have

an adult cut out the picture using

a utility knife or trace the heart

shape and cut out with scissors.

Open the Compartment using

your fingernail as shown.

Place the new heart-shaped

picture into the faceplate and

shut the compartment.

DDC9000P.qxp 7/15/05 10:39 AM Page 5

RECHARGING THE BATTERY

The battery is not replaceable in this unit as it is rechargeable and

does not need replacing. Charge the battery before using for the first

time. To recharge, follow the instructions below:

GETTING STA R T E D

Open the Compartment using

your fingernail as shown.

Insert the small end of the USB

cable into this camera and the

other end into the USB port on

your computer; a beep will sound

to signal the unit is charging.

When charging for the first time, charge for 10 to 12 hours. After the

initial charging, it will only take one to two hours to charge. This

rechargeable battery can be recharged up to 500 times.

CHECKING THE BATTERY LEVEL

Follow the instructions below to check the battery level of the

rechargeable battery:

Press the Mode/Power button once to

turn the unit on. If the battery power is

l o w, the remaining photo counter

number will blink in the display In this

case, recharge the batteries as

described above.

DDC9000P.qxp 7/15/05 10:39 AM Page 6

GETTING STARTED (CONTINUED)

USING THE NECKLACE

You can attach this camera to the supplied necklace as follows:

IMPORTANT SAFETY FEATURE:

The necklace contains a safety strap that will come

apart if a strong pulling force occurs to the necklace.

This is a safety feature for children to prevent

s t r a n g u l a t i o n .

Push the tab on the connector.

Connect to the Camera’s loop.

DDC9000P.qxp 7/15/05 10:39 AM Page 7

O P E R AT I O N

TURNING THE POWER ON/OFF

Press the Mode/Power button 1 once

to turn the unit on. To turn the camera

off, press the Mode/Power button 1

until “oF” appears in the display, then

press the Shutter/Select button 2.

NOTES:

• The power will automatically turn on when a USB cable is

connected to the computer and turn off when the USB cable is

removed.

• To save the battery power, the unit will automatically turn off after

20 seconds of inactivity, but the pictures will remain in memory.

DDC9000P.qxp 7/15/05 10:40 AM Page 8

O P E R ATION (CONTINUED)

Press the Mode/Power button

once to turn the unit on.

The counter (i.e. '25', '18', etc.)

will appear in the display.

Press the Shutter/Select button to

take a picture; the LED will blink

once and the counter in the

display will decrease by one.

TAKING A SINGLE PICTURE

Turn the camera on as described

on page 8. Press the Mode/Power

button twice to select the Self

Timer mode; “St” will appear in the

display.

Within three seconds, press the

Shutter/Select button to select the

Self Timer mode. The LED will

blink and the camera will beep

nine times. On the tenth beep, the

picture will be taken.

SETTING THE SELF TIMER MODE

DDC9000P.qxp 7/15/05 10:40 AM Page 9

O P E R ATION (CONTINUED)

Turn the camera on as

described on page 8. Press the

Mode/Power button three times

to select the Video mode; “d8”

will appear in the display.

Within three seconds, press and hold

the Shutter/Select button to start taking

continuous pictures. For this function,

the counter will rapidly decrease.

When you release the Shutter/Select

button, it will stop taking photos and

the counter will shown the remaining

photos number in the display.

SETTING THE CONTINUOUS SNAPSHOT PICTURES MODE

Turn the camera on as described

above. Press the Mode/Power

button four times to select the

Three Continuous Pictures mode;

“CS” will appear in the display.

Within three seconds, press the

Shutter/Select button to start

taking three continuous pictures.

The LED will blink three times and

the counter will decrease by three.

TAKING THREE CONTINUOUS PICTURES

NOTE: The Three Continuous Pictures function is only available for HI (High)

image quality mode. If you using this function while in Lo (Low) image quality

mode, when you take the pictures, the unit will change to Hi (High) image quality

mode to take 3 pictures automatically then revert to Lo (Low) image quality mode.

NOTE :The Continuous Snapshot Pictures function is only available for Lo

(Low) image quality mode. If you using this function while in Hi(High) image

quality mode, when you take the pictures, the unit will change to (Lo) Low

image quality mode automatically. When you release the Shutter/Select

button. It will stop taking photos and returns to Hi (High) image quality mode.

DDC9000P.qxp 7/15/05 10:40 AM Page 10

O P E R ATION (CONTINUED)

Turn the camera on as

described on page 8. Press the

Mode/Power button five times to

select the Clear All mode; “CA”

will appear in the display.

Within three seconds, press the

Shutter/Select button to enter

the Clear All mode; “CA” will

blink in the display. Press again

to confirm; all pictures taken will

be deleted.

TO DELETE ALL PICTURES

Turn the camera on as

described on page 8. Press the

Mode/Power button six times to

select the Clear Last mode; “CL”

will appear in the display.

Within three seconds, press the

Shutter/Select button and the last

picture taken will be deleted. After

you continuous snapshot pictures,

if you select the Clear Last mode

"CL" and press the Shutter/Select

button, the last continuous

snapshot pictures will be deleted.

TO DELETE THE LAST PICTURE OR LAST CONTINUOUS PICTURES

DDC9000P.qxp 7/15/05 10:40 AM Page 11

O P E R ATION (CONTINUED)

Turn the camera on as

described on page 8. Press the

Mode/Power button seven times

to select the Image Quality; “Hi”

or “Lo” will appear in the display.

Within 3 seconds, press the

Shutter/Select button to select

the Quality mode as shown on

the display i.e. if Lo appears,

press the Shutter/Select button

to change the setting to Low.

SETTING THE IMAGE QUALITY MODE

Select the desired resolution as shown below, Hi (640 x 480 pixels)

or Lo (320 x 240 pixels) as follows:

NOTES:

•

Lo(w) Resolution file size is smaller, but the quality is not as

good as Hi(gh). Lo(w) is ideal for e-mailing.

•

The capacity for pictures in Lo(w) Resolution is 100; and for

pictures in Hi(gh) Resolution is 25.

DDC9000P.qxp 7/15/05 10:40 AM Page 12

O P E R ATION (CONTINUED)

Turn the camera on as described

on page 8. Press the

Mode/Power button eight times to

select the Frequency mode; “60”

or “50” will appear in the display.

Within 3 seconds, press the

Shutter/Select button to select

the Frequency mode as shown

on the display i.e. if 60 appears,

press the Shutter/Select button

to change the setting to 60.

SETTING THE FREQUENCY MODE

Because the electrical power frequency is either 50Hz or 60Hz,

depending on the country you are located in, please set it according

to the country that you are located in. If located in USA, set to 60Hz.

To restore the camera to the

factory defaults, press the

R E S E T button (inside

compartment) using a pin or

similar item.

RESET BUTTON

DISPLAY

The display can only display two

digits. Although the capacity for

pictures in Lo(w) Resolution is

100, the display will show 99 until

two pictures have been taken

and then change to 98.

RESET BUTTON NOTE: When

you press the RESET button, all

the taken photos in the camera

will be deleted.

DDC9000P.qxp 7/15/05 10:40 AM Page 13

I N S TALLING THE CAMERA S O F T WA R E :

I M P O R TANT NOTES:

• This digital camera is for use with PCs only and can not be used with

Macintosh computers.

• Before and while installing the software, make sure that you do not have

the camera or the USB cable attached to your computer. This will adversely

a f fect the install process and will cause installation to fail.

1 . Insert the CD into your CD Rom Drive.

2 . The "Install Your Camera Software" screen

will appear, select the "Disney Princess

Digital Camera" from the drop-down list

and click the "Install" button to install the

NHJ Photo Manager. This will be followed

by the installation of the NHJ Web Cam

Express and your camera driver.

3 . On the “NHJ Photo Manager” install

screen, click the “Next” button.

4 . Please review the license terms and click

the “Agree” button to continue.

COMPUTER CONNECTION

DDC9000P.qxp 7/15/05 10:40 AM Page 14

5 . Let the “NHJ Photo Manager” installer

create the folder where the program will be

installed to, and then click “Install”.

Warning: DO NOT change the installation path.

Otherwise, the driver may not run properly. '

6 . Click “Finish” to let the “NHJ Photo

Manger” installer finish the installation

p r o c e s s .

7 . Next the install program for the camera

driver will automatically launch. Click “Next”

to continue.

8 . You have successfully installed the “NHJ

Photo Manager” software, the “NHJ We b

Cam Express” and the camera driver.

9 . Click on “Finish” and restart your computer

before you connect your camera to your PC.

COMPUTER CONNECTION (CONTINUED)

DDC9000P.qxp 7/15/05 10:40 AM Page 15

U N I N S TALLING THE CAMERA S O F T WA R E :

NHJ PHOTO MANAGER

1 . To uninstall the “NHJ

Photo Manager” software

and the “NHJ Web Cam

Express” software, click

the “Start” menu on the

Windows desktop. Choose the “NHJ Photo Manager” in the “All Programs”

menu. Then choose “Uninstall NHJ Photo Manager” and follow the on-

screen instructions.

U N I N S TALLING THE CAMERA D R I V E R

I M P O R TANT NOTE:

• Do not uninstall the driver unless instructed by a customer service

t e c h n i c i a n .

1 . Open the “Control Panel” in Wi n d o w s .

2 . Select “Add or Remove Programs”.

3 . Locate “Disney Princess Camera” and select “Change/Remove”.

4 . Follow the on-screen instruction to uninstall the CAMERA D R I V E R .

DOWNLOADING PHOTO S :

1 . Plug one end of the USB cable into the USB

jack on your camera (inside compartment).

2. Plug the other end of the USB cable into a

USB port on your computer.

3 . Confirm that your camera is connected and

turned on.

4 . Double-click the “NHJ Photo Manager” icon

that is on your desktop to launch the “NHJ

Photo Manager” program.

COMPUTER CONNECTION (CONTINUED)

DDC9000P.qxp 7/15/05 10:40 AM Page 16

5 . Click on the “Get Photos” button on

the Main Menu.

6 . The “Get Photos” wizard will appear with

the correct name of your camera device

(DDC9000-P) already selected in the

“Active Devices” list in the “Express” mode.

Click the “Next” button to proceed.

7 . On the next screen, choose where you

want to place your photos and click the

“Finish” button to copy the photos and

video clips continuous images taken to

your computer.

8 . Select the size of the pictures:

i) For regular size: Do not click the check

box, just click 'OK'. (Regular image size is

640 x 480 pixels.)

ii) For double enlarge image size: Click

on the check box, then click 'OK'.

(Double image size is 1280 x 960

p i x e l s . )

COMPUTER CONNECTION (CONTINUED)

DDC9000P.qxp 7/15/05 10:40 AM Page 17

9 . All of the pictures and video clip

continuous images you imported will

then appear in “Select Photos” mode’s

main window.

1 0 . You can now follow the on-screen

instructions to enhance photos, add

captions, share photos or use the “NHJ

Photo Manager” Wo r k s h o p !

USING YOUR CAMERA AS A WEB CAM:

1 . Connect your camera to your PC as previously instructed.

2 . If desired, connect a microphone (not included) to your audio card’s

external microphone connector.

3 . Follow steps 1 to 4 as described on page 17. Then Click on the "We b C a m

Express”; the WEB CAM will appear on the desktop. For the uses of the

WebCAM or additional assistance, click on the "Show Me How" button at

the upper right side of the screen. Then you can view the instruction for the

WebCam on the pop up window.

CAPTURING AVI VIDEO FILES:

I M P O R TANT NOTE:

• AVI files (short movies) take up a lot of hard drive space.

1 . Follow 'USING YOUR CAMERA AS A WEB CAM' (as described above) to

activate the web cam.

2 . Click the “Capture” button to start recording the

video. The recording’s elapsed time will appear

under the video.

NOTE: When you click the "Capture" button, it will

start capturing video for 1 minute and then stop

r e c o r d i n g .

COMPUTER CONNECTION (CONTINUED)

DDC9000P.qxp 7/15/05 10:40 AM Page 18

3 . Click the “Pause” button to pause the

recording. To continue recording, click the

“Capture” button again.

4. To finish recording, click the “Stop” button.

5 . The videos will automatically be saved into a default directory.

N O T E S :

• To learn how to capture JPEG s n a p s h o t s

from your Web Cam or from your existing

AVI movies, go to the “Take Snapshots”

section of “Show Me How”.

• To learn how to change the user settings,

go to “Help” on the main page of “NHJ

Photo Manager”.

USING MICROSOFT NETMEETING:

Windows XP/2000 users can also use Microsoft NetMeeting with the Web Cam.

Visit http://www.Microsoft.com/windows/netmeeting for more information.

NHJ PHOTO MANAGER TO U R

For more details of the 'NHJ Photo Manager', click the "Start" menu on the

Windows desktop and choose the "NHJ Photo Manager" in the "All Programs"

menu. Then choose "NHJ Photo Manager Tour". You can select the function

icons to view the

description of the functions

in the "NHJ Photo

Manager" window. "

COMPUTER CONNECTION (CONTINUED)

DDC9000P.qxp 7/15/05 10:40 AM Page 19

La page charge ...

Disney DDC9000-P Manuel utilisateur

Marque: Disney

Modèle: DDC9000-P

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Disney DDC9000-P User manual
español: Disney DDC9000-P Manual de usuario

Documents connexes

Disney DDC9000-P Manuel utilisateur

Disney DDC9000-P Manuel utilisateur

Disney DDC9000-P Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents