ETC fos/4 Panel Mode d'emploi

ETC
Marque
ETC
Modèle
fos/4 Panel
Catégorie
Stroboscopes
Taper
Mode d'emploi

Ce manuel convient également à

ETC Quick Guide
fos/4 Panel
Corporate Headquarters Middleton, WI, USA +1 608 831 4116 London, UK +44 (0)20 8896 1000
Holzkirchen, DE +49 (80 24) 47 00-0 Rome, IT +39 (06) 32 111 683 Hong Kong +852 2799 1220 Paris, FR +33 1 4243 3535
Web etcconnect.com Support support.etcconnect.com Contact etcconnect.com/contactETC
© 2020 Electronic Theatre Controls, Inc. Trademark and patent info:etcconnect.com/ip
Product information and specifications subject to change. ETCintends this document to be provided in its entirety.
7471M1300-1.0.0 Rev A Released 2020-01
Overview
Use the images below as a guide to connect power and data and to navigate the basic features of the
fixture. For complete information, download the
fos/4 Panel User Manual
at etcconnect.com.
C
B
B
D
F
E
C
G
A
A
C
H
I
I
H
B
Medium
(PL16 or PD16)
Small
(PL8 or PD8)
Large
(PL24 or PD24)
A
Accessory holder:
Insert accessories into the two available slots from either side of the holder, and
then lock the holder (
page5
).
B
Handles:
For medium (PL16 or PD16) and large (PL24 or PD24) fixtures, carry the fixture by the pairs
of handles on the back of the fixture, and attach safety cables to handles when mounting the fixture.
C
Yoke tilt-lock:
Tilt the fixture as needed, and then turn the tilt-lock clockwise to lock the position. If
necessary, press the center button on the tilt-lock to adjust the tilt-lock position.
D
Battery connector: Four-pin XLRconnector for battery power (not available on PL24 or PD24).
Connect the fixture to battery power only when AC power is not available. Do not connect the fixture
to a battery and to AC power at the same time.
E
Power In and Power Thru connectors:
powerCON
®
TRUE1 TOP connectors for power in and power
thru.
The large fixture (PL24 or PD24) has a connector for power in only (no power thru connector).
F
User interface:
View the fixture status, set the DMXaddress and mode, or set stand-alone options.
G
DMX In and DMX Thru connectors:
Five-pin XLRconnectors for DMX/RDM in and DMX/RDMthru.
H
Griprail:
Attach standard accessories and mounting hardware to the back of the fixture using the
hardware provided with the accessories or using M6 standard T-nuts.
I
Safety cable attachment points:
Small (PL8 or PD8) fixture only. For large and medium fixtures,
attach safety cables to handles (
B
), either the top pair or the bottom pair (
page4
).
ETC Quick Guide
fos/4 Panel
fos/4 Panel Page 2 of 8 ETC
User Interface
Effects
Effect Flicker
Rate 200
Min 0%
Max Int 100%
DMX
C
D
A
F
H
I
G
E
B
A
Display:
The colors of options on the display correspond to the colors of the encoders below the
display (
F
) and the Intensity encoder to the right of the display(
B
).
B
Intensity encoder:
•
When in DMX mode, press the Intensity encoder to enter Focus mode when focusing the fixture.
•
When configuring the fixture in one of the stand-alone modes, press the Intensity encoder to
toggle between the current intensity and 0, or turn the Intensity encoder to modify the white
fields on the display. See
Use Fixture in Stand-aloneMode on page7
.
•
When navigating from the Main Menu screen, turn the Intensity encoder to scroll through menu
options, and then press the Intensity encoder to select a menu option.
C
Menu button:
Press to view the
Main Menu
screen and configure the fixture. Press the button again
to return to the previous screen when you are setting configuration options.
D
Function button:
Press repeatedly to toggle through the following modes:
•
Studio: Use one of three studio (white light) presets, or customize the presets.
•
Color: Use one of 12 color presets, or customize the presets.
•
Preset: Use one of 12 presets (color preset + fade time), or customize the presets.
•
Effects: Use one of 12 effects, or customize the effects.
•
DMX: View and set DMX parameters for the fixture.
See
Use Fixture in Stand-aloneMode on page7
and
Use Fixture in DMX Mode on page6
.
E
Antenna:
For use when controlling the fixture using wireless DMX.
F
Encoders(Red, Green, Blue):
The colors of encoders correspond to options on the display. Press to
activate the options at the bottom of the display, or turn to modify the values on the display.
G
NFC(Near Field Communication) tag:
Use the Set Light app to wirelessly configure the fixture,
with or without power applied to the fixture.
H
USB port:
Use for updating firmware, saving and loading fixture configuration settings, or saving
error logs via a flash drive.
I
UI lock:
Set this switch to lock the UI. This prevents inadvertent changes to the UI.
ETC Quick Guide
fos/4 Panel
fos/4 Panel Page 3 of 8 ETC
Safety
IMPORTANT SAFEGUARDS
When using electrical equipment, basic safety precautions should always be followed including the
following:
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
•
Do not use outdoors.
•
Do not let power supply cords touch hot surfaces.
•
Do not mount near gas or electric heaters.
•
Equipment should be mounted in locations and at heights where it will not readily be subjected
to tampering by unauthorized personnel.
•
The use of accessory equipment not recommended by the manufacturer may cause an unsafe
condition.
•
Do not use this equipment for other than intended use.
SAVE THESE INSTRUCTIONS
WARNING: Note the following safety warnings before use:
•
Use the fixture in dry locations only, where humidity does not exceed 90
percent (non-condensing).
•
Connect the fixture to a non-dimmable power source in order to avoid
damage to the fixture's internal power supply and other electrical
components. Using a dimmable power source can damage the fixture and
will void the warranty.
WARNING: Note the following safety warnings before use:
•
Disconnect the fixture from power and DMX and allow it to cool before
installing accessories or performing any cleaning and maintenance.
•
Only use mounting hardware that is rated for the total weight of the
fixture and accessories.
•
In addition to primary suspension, attach a safety cable (or other approved
safety device) to the fixture. Safety cables must be rated to support six
times the fixture weight. See
Mounting and Safety Cables on the next
page
.
•
Check that the accessory holder is locked and that any accessory safety
cables are connected before mounting the fixture.
•
Do not mount the fixture on or near a flammable surface.
•
Do not operate the fixture without the diffusion installed.
•
Do not use this fixture with a damaged power lead. If the power lead
(cord set) is damaged, it must be replaced.
•
Do not use this fixture if the diffusion is deeply scratched or cracked. You
must replace the diffusion when it is damaged.
ETC Quick Guide
fos/4 Panel
fos/4 Panel Page 4 of 8 ETC
AVERTISSEMENT : Prendre connaissance des avertissements de sécurité
suivants avant toute utilisation :
•
Débranchez le projecteur de son alimentation et du DMX et laissez-le
refroidir avant d’installer des accessoires ou d’effectuer un nettoyage ou
un entretien.
•
N’utilisez que de la quincaillerie de montage adaptée au poids total des
projecteurs et des accessoires.
•
En plus de la suspension principale, fixez une chaîne de sécurité (ou tout
autre dispositif de sécurité homologué) au projecteur. Les chaînes de
sécurité doivent être en mesure de supporter six fois le poids du
projecteur.
•
Vérifiez que le porte-accessoires est verrouillé et que les élingues de tous
les accessoires sont bien attachées avant de monter le projecteur.
•
Ne pas installer le projecteur sur ou à côté d’une surface inflammable.
•
N’utilisez pas le projecteur sans que le diffuseur soit installé.
•
Ne pas utiliser ce projecteur avec un cordon d’alimentation endommagé.
Si le cordon d’alimentation (câble) est abîmé, il doit être remplacé.
•
N’utilisez pas ce projecteur si le diffuseur présente des rayures ou des
fissures profondes. Il faut remplacer le diffuseur s'il est abîmé.
Mounting and Safety Cables
You can mount the fixture using a clamp, junior (28mm) pin (included), or appropriate mounting
hardware on the yoke, or you can set the fixture on the floor or another flat surface. When
suspending the fixture, make sure to secure the fixture with appropriate safety cables at the safety
cable attachment points on the small (PL8 or PD8) fixture or at the handles using a looped
attachment on the medium (PL16 or PD16)and large (PL24 or PD24)fixtures.
Small (PL8 or PD8)
Attach safety cables to
the connection points
Medium (PL16 or PD16) and
Large (PL24 or PD24)
Attach safety cables to either
pair of handles using looped
attachments (see inset)
ETC Quick Guide
fos/4 Panel
fos/4 Panel Page 5 of 8 ETC
Fixture Weights
14.5 kg (32 lb)
25.4 kg (56 lb)
35.8 kg (79 lb)
PL8
PD8
PL16
PD16
PL24
PD24
A
B
Add Accessories
You can use up to two standard accessories (one diffusion
and one additional accessory, such as a barn door) in the
accessory holder.
1. Unlock the accessory holder on either side by pressing
and sliding both accessory holder locks (A), and then
rotating the accessory holder door (B).
2. Slide an accessory into one of the accessory slots. You
can add a second accessory in the other slot, if
needed.For diffusion accessories, verify that the rough
side of the diffusion faces the LEDs and that you can
read the label text on the diffusion from the front of
the fixture.
3. Lock the accessory holder by closing the door and
sliding the locks back into position.
Connect Power andData
Power:Either powerCON TRUE1 TOP connectors for ACpower (100–240VAC, 50/60 Hz on a non-
dimmable circuit) or four-pin XLR connectors for battery power (24–36VDC) on the small (PL8 or
PD8) and medium (PL16 or PD16) fixtures
Data: Five-pin XLR connectors for DMX In and DMXThru
CAUTION:
Do not connect the fixture to the battery when AC power is present.
Maximum fixture output may be reduced when the fixture is connected to battery
power.
Focus the Fixture
1. Apply power to the fixture, and wait until the fixture has booted up(the ETC splash screen
displays during boot up).
2. Press any encoder to "wake" the display.
3. What screen is currently displayed?
•
DMX:Press the Intensity encoder to turn on the LED array. The display shows a timeout
countdown to indicate how long the LED array will remain on at 100% intensity. You can
turn the Intensity encoder to reset the timeout countdown to 5minutes.
•
All other screens (Studio, Preset, etc.): Press the Intensity encoder to turn on the
LEDarray, and turn the Intensity encoder to adjust the intensity.
4. Adjust the fixture to the desired position.
5. Press the Intensity encoder to turn off the LEDarray.
ETC Quick Guide
fos/4 Panel
fos/4 Panel Page 6 of 8 ETC
Use Fixture in DMX Mode
After you connect power and data to the fixture and provide DMX, press the Function button ( )
repeatedly to toggle to the DMX screen, where you can set the DMX address, DMXmode, and
DMXloss behavior. (You can also set these values using RDM.)
The DMX screen displays the current DMX values. Press any of the encoders to "wake" the display
and edit the values. The colors of the encoders correspond to options on the display. Turn an
encoder to modify the corresponding value.
DMX
Address
Mode
DMX Loss
1/3 Red
DMX
Address
Mode
DMX Loss
1/3 Red
001
3 Ch RGB
HLL
001
3 Ch RGB
HLL 2 Min
Press any encoder to wake the display... ...and then turn an encoder to modify the value in
the matching field. Press an encoder again to
return to the view-only screen.
DMXModes
Direct
(DaylightHDR)
Direct
(Lustr X8)
Expanded Studio 3 Ch RGB 1 Channel
RDMPersonality ID
1 1 2 3 4 5
DMXChannel
1 Intensity Intensity Intensity Intensity Red Intensity
2 Deep Red Deep Red CCT CCT Green
3 Red Red Tint Tint Blue
4 Mint Amber Tuning Tuning
5 Cyan Lime Mix Strobe
6 Blue Green Red Curve
7 Indigo Cyan Green Fan
8 Strobe Blue Blue
9 Curve Indigo Strobe
10 Fan Strobe Curve
11 Curve Fan
12 Fan
ETC Quick Guide
fos/4 Panel
fos/4 Panel Page 7 of 8 ETC
Use Fixture in Stand-aloneMode
After you connect power to the fixture, press the Function button ( ) repeatedly to toggle through
the following modes:
•
Studio: Use one of three studio (white light) presets, or customize the presets.
•
Color: Use one of 12 color presets, or customize the presets.
•
Preset: Use one of 12 presets (color preset + fade time), or customize the presets.
•
Effects: Use one of 12 effects, or customize the effects.
•
DMX: View and set DMX parameters for the fixture.
The colors of options on the display correspond to the colors of the encoders below the display and
the Intensity encoder to the right of the display. Turn an encoder to modify the corresponding value
on the display, or press an encoder to activate the corresponding option at the bottom of the display.
Press the Intensity encoder to toggle between the current intensity and 0%.
If the fixture is connected to other fos/4 Panel fixtures that are in the same stand-alone mode, the
connected fixtures will play the same preset or effect.
If the fixture is receiving DMX, the DMXdata overrides any stand-alone mode selections. When the
fixture is no longer receiving DMX, then the stand-alone selections take effect.
Select a Color Temperature
1. Press the Function button ( ) until the display shows the Studio screen.
DMX
DMX
2. Press the color encoder that matches the studio preset you want to use.
•
Blue: 3200K
•
Green: 4500K
•
Red: 5600K
More Options
•
Turn off the preset: Press the Intensity encoder to toggle the intensity value from the current
value to 0. Press the Intensity encoder again to toggle back to the previous intensity value.
ETC Quick Guide
fos/4 Panel
fos/4 Panel Page 8 of 8 ETC
•
Modify the preset:Turn the encoders to change the corresponding values. For example, turn
the Intensity encoder to change the intensity value, or turn the blue encoder to change the
color temperature value.
•
Revert to the original preset:Press the encoder that corresponds to the preset again to restore
the original values.
•
Save the modified preset:Press and hold the encoder that corresponds to the preset that you
want to re-record. The display shows a three-second countdown before re-recording the
preset.
Select a Color
1. Press the Function button ( ) until the display shows the Color screen.
2. Turn the encoders to change the corresponding values. For example, turn the Intensity
encoder to change the intensity value, or turn the green encoder to change the hue value. The
crosshairs on the display indicate the approximate color.
You can use a preset as a starting point for a color by pressing the color encoder that matches
the preset. Turn the red encoder to move to another page of presets.
More Options
•
Turn off the color: Press the Intensity encoder to toggle the intensity value from the current
value to 0. Press the Intensity encoder again to toggle back to the previous intensity value.
•
Revert to the original color of a preset: Press the encoder that corresponds to the preset again
to restore the original values.
•
Save the color to a preset:Press and hold the encoder that corresponds to the preset that you
want to re-record. The display shows a three-second countdown before re-recording the
preset. Changes that you make to presets in the Color screen also affect presets in the Effects
screen and the Preset screen.
Select a Preset
1. Press the Function button ( ) until the display shows the Preset screen.
2. Turn the green encoder to select a preset, and then press the encoder to play the preset.
More Options
•
Pause the preset: Press the green encoder to toggle between play and pause.
•
Stop the preset: Press the red encoder.
•
Modify the preset:Turn the Intensity encoder to change the intensity, or turn the red encoder
to change the fade value.
•
Capture the current DMX look: Press and hold the blue encoder (for the Snapshot icon ).
The display shows a 3-second countdown before re-recording the preset.
•
Modify the preset color:Press the blue encoder (for the Edit icon ). In the Edit Preset Color
screen, turn the encoders to change the corresponding values. The crosshairs on the display
indicate the approximate color. Press the green encoder (for the Save icon ) to save the
new color to the preset.
•
Push the preset to connected fixtures:Press the Menu button ( ), and then use the Intensity
encoder to navigate through the menu: Local Settings>Push Presets. When the screen
prompts you to confirm, press the green encoder (for the OK icon ) to continue.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

ETC fos/4 Panel Mode d'emploi

ETC
Marque
ETC
Modèle
fos/4 Panel
Catégorie
Stroboscopes
Taper
Mode d'emploi
Ce manuel convient également à
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents