Hitachi CG 22S Safety Instructions And Instruction Manual

SAFETY INSTRUCTIONS AND INSTRUCTION MANUAL

WARNING

IMPROPER OR UNSAFE use of this power tool can result in death or serious bodily injury!

This manual contains important information about product safety. Please read and understand this manual

BEFORE operating the power tool. Please keep this manual available for other users and owners before they

use the power tool. This manual should be stored in safe place.

WARRANTY: CG22EAB(SLP),

CG22EAB(L) are NOT intended for commercial use, and therefore, NO warranty is provided to their

commercial applications and rental applications.

INSTRUCTIONS DE SECURITE ET MODE D’EMPLOI

AVERTISSEMENT

Une utilisation INCORRECTE OU DANGEREUSE de cet outil motorisé peut entraîner la mort ou de

sérieuses blessures corporelles !

Ce mode d’emploi contient d’importantes informations à propos de la sécurité de ce produit. Prière de

lire et de comprendre ce mode d’emploi AVANT d’utiliser l’outil motorisé. Garder ce mode d’emploi à la

disponibilité des autres utilisateurs et propriétaires avant qu’ils utilisent l’outil motorisé. Ce mode d’emploi

doit être conservé dans un endroit sûr.

GARANTIE : Les modèles CG22EAB(SLP) et

CG22EAB(L) NE sont PAS destinés à un usage commercial, par conséquent, AUCUNE garantie n’est

fournie concernant toute utilisation commerciale ou locative.

INSTRUCCIONES DE SEGURIDAD Y MANUAL DE INSTRUCCIONES

ADVERTENCIA

¡La utilización INAPROPIADA O PELIGROSA de esta herramienta eléctrica puede provocar lesiones

graves o la muerte!

Este manual contiene información importante sobre la seguridad del producto. Lea y comprenda este manual

ANTES de utilizar la herramienta eléctrica. Guarde este manual para que puedan leerlo otras personas

antes de utilizar la herramienta eléctrica. Este manual debe ser guardado en un lugar seguro.

GARANTÍA: CG22EAB(SLP),

LOS CG22EAB(L) no están destinados a uso comercial y, por lo tanto, NO se garantizan sus aplicaciones

comerciales y aplicaciones de alquiler.

CG 22EAS (SLP)

CG 22EAS (SL)

CG 22EAS (S)

CG 22EAD (SLP)

CG 22EAD (SL)

CG 22EAB (SLP)

CG 22EAB (L)

CG 24EASP (SL)

CG 24EASP (S)

CG 27EASP (SL)

CG 27EASP (S)

Grass Trimmer/Brush Cutter

Coupe-Herbes/Débroussailleuse

Motoguadañas/Desbrozadoras

CG22EAS (SLP)

Designed for operating in USA & Canada only.

When this product is used in areas other than the USA & Canada,

we cannot guarantee the product quality and performance.

2

English

MEANINGS OF SYMBOLS

NOTE: Some units do not carry them.

Symbols

WARNING

The following show symbols used for the machine. Be sure that you understand

their meaning before use.

It is important that you read, fully

understand and observe the

following safety precautions and

warnings. Careless or improper

use of the unit may cause serious

or fatal injury.

Gloves should be worn

when necessary, e.g.,

when assembling cutting

equipment.

Read, understand and follow all

warnings and instructions in this

manual and on the unit.

Use anti-slip and sturdy

footwear.

Always wear eye, head and ear

protectors when using this unit.

Blade thrust may occur when

the spinning blade contacts

a solid object in the critical

area. A dangerous reaction

may occur causing the entire

unit and operator to be thrust

violently. This reaction is called

blade thrust. As a result, the

operator may lose control of the

unit which may cause serious

or fatal injury. Blade thrust is

more likely to occur in areas

where it is diﬃ cult to see the

material to be cut.

Do not use metal/rigid blades

when this sign is shown on the

unit.

Keep all children, bystanders and

helpers 50 ft (15 m) away from

the unit. If anyone approaches

you, stop the engine and cutting

attachment immediately.

Indicate handle location. Do

not attach handle above this

point.

Be careful of thrown objects.

Indicate blade guard location

for a trimmer head or semi-

auto cutting head.

Shows maximum shaft speed. Do

not use the cutting attachment

whose max rpm is below the

shaft rpm.

Before using your machine

• Read the manual carefully.

• Check that the cutting equipment is correctly assembled and adjusted.

• Start the unit and check the carburetor adjustment. See “MAINTENANCE”.

Contents

WHAT IS WHAT .................................................... 3

WARNINGS AND SAFETY INSTRUCTIONS ........ 4

WARRANTY .......................................................... 5

SPECIFICATIONS ................................................. 6

ASSEMBLY PROCEDURES ................................. 8

OPERATING PROCEDURES .............................. 12

MAINTENANCE .................................................. 15

3

English

16

17

13

7

6

2

5

4

10

13

11

9

7

6

14

5

4

2

13

11

9

7

15

6

14

5

4

2

13

9

11

7

6

5

4

2

9

11

13

8

7

6

5

14

4

3

12

1

WHAT IS WHAT

Since this manual covers several models, there may

be some diﬀ erence between pictures and your unit.

Use the instructions that apply to your unit.

1. Fuel cap

2. Throttle trigger

3. Starter handle

4. Blade guard

5. Cutting attachment

6. Drive shaft tube

7. Handle

8. Suspension eyelet

9. Ignition switch

10. Harness

11. Throttle trigger lockout

12. Choke lever

13. Engine

14. Angle transmission

15. Joint case

16. Combi box spanner

17. Handling instructions

CG 22EAS (S)

CG 24EASP (S)

CG 27EASP (S)

CG 22EAB (L)

CG 22EAB (SLP)

CG 22EAD (SLP)

CG 22EAD (SL)

CG 22EAS (SLP)

CG 22EAS (SL)

CG 24EASP (SL)

CG 27EASP (SL)

4

English

WARNINGS AND SAFETY

INSTRUCTIONS

Operator safety

○ Always wear a safety face shield or goggles.

○ Always wear heavy, long pants, boots and

gloves. Do not wear loose clothing, jewelry, short

pants, sandals or go barefoot. Secure hair so it is

above shoulder length.

○ Do not operate this tool when you are tired,

ill or under the inﬂ uence of alcohol, drugs or

medication.

○ Never let a child or inexperienced person operate

the machine.

○ Wear hearing protection. Pay attention to your

surroundings. Be aware of any bystanders who

may be signaling a problem. Remove safety

equipment immediately upon shutting oﬀ engine.

○ Wear head protection.

○ Never start or run the engine inside a closed

room or building. Breathing exhaust fumes can

kill.

○ Keep handles free of oil and fuel.

○ Keep hands away from cutting equipment.

○ Do not grab or hold the unit by the cutting

equipment.

○ When the unit is turned oﬀ , make sure the cutting

attachment has stopped before the unit is set

down.

○ When operation is prolonged, take a break from

time to time so that you may avoid possible

Hand-Arm Vibration Syndrome (HAVS) which is

caused by vibration.

WARNING

● Antivibration systems do not guarantee that

you will not sustain Hand-Arm Vibration

Syndrome or carpal tunnel syndrome.

Therefore, continual and regular users

should monitor closely the condition of

their hands and ﬁ ngers. If any symptoms

of the above appear, seek medical advice

immediately.

● If you are using any medical electric/

electronic devices such as a pacemaker,

consult your physician as well as the device

manufacturer prior to operating any power

equipment.

Unit/machine safety

○ Inspect the entire unit/machine before each use.

Replace damaged parts. Check for fuel leaks

and make sure all fasteners are in place and

securely tightened.

○ Replace parts that are cracked, chipped or

damaged in any way before using the unit/

machine.

○ Make sure the safety guard is properly attached.

○ Keep others away when making carburetor

adjustments.

○ Use only accessories as recommended for this

unit/machine by the manufacturer.

WARNING

Never modify the unit/machine in any way.

Do not use your unit/machine for any job

except that for which it is intended.

Fuel safety

○ Mix and pour fuel outdoors and where there are

no sparks or ﬂ ames.

○ Use a container approved for fuel.

○ Do not smoke or allow smoking near fuel or the

unit/machine or while using the unit/machine.

○ Wipe up all fuel spills before starting engine.

○ Move at least 10 ft (3 m) away from fueling site

before starting engine.

○ Stop engine before removing fuel cap.

○ Empty the fuel tank before storing the unit/

machine. It is recommended that the fuel be

emptied after each use. If fuel is left in the tank,

store so fuel will not leak.

○ Store unit/machine and fuel in area where fuel

vapors cannot reach sparks or open ﬂ ames

from water heaters, electric motors or switches,

furnaces. etc.

WARNING

Fuel is easy to ignite or get explosion or

inhale fumes, so that pay special attention

when handling or ﬁ lling fuel.

Cutting safety

○ Do not cut any material other than grass and

brush.

○ Inspect the area to be cut before each use.

Remove objects which can be thrown or become

entangled.

○ For respiratory protection, wear an aerosol

protection mask when cutting the grass after

insecticide is scattered.

○ Keep others including children, animals,

bystanders and helpers outside the 50 ft (15 m)

hazard zone. Stop the engine immediately if you

are approached.

○ Always keep the engine on the right side of your

body.

○ Hold the unit/machine ﬁ rmly with both hands.

○ Keep ﬁ rm footing and balance. Do not over-

reach.

5

English

○ Keep all parts of your body away from the muﬄ er

and cutting attachment when the engine is

running.

○ Keep cutting attachment below waist level.

○ When relocating to a new work area, be sure to

shut oﬀ the machine and ensure that all cutting

attachments are stopped.

○ Never place the machine on the ground when

running.

○ Always ensure that the engine is shut oﬀ and any

cutting attachments have completely stopped

before clearing debris or removing grass from the

cutting attachment.

○ Always carry a ﬁ rst-aid kit when operating any

power equipment.

○ Never start or run the engine inside a closed

room or building and/or near inﬂ ammable liquids.

Breathing exhaust fumes can kill.

Maintenance safety

○ Maintain the unit/machine according to

recommended procedures.

○ Disconnect the spark plug before performing

maintenance except for carburetor adjustments.

○ Keep others away when making carburetor

adjustments.

○ Use only genuine Hitachi replacement parts as

recommended by the manufacturer.

Transport and storage

○ Carry the unit/machine by hand with the engine

stopped and the muﬄ er away from your body.

○ Allow the engine to cool, empty the fuel tank,

and secure the unit/machine before storing or

transporting in a vehicle.

○ Empty the fuel tank before storing the unit/

machine. It is recommended that the fuel be

emptied after each use. If fuel is left in the tank,

store so fuel will not leak.

○ Store unit/machine out of the reach of children.

○ Clean and maintain the unit carefully and store it

in a dry place.

○ Make sure engine switch is oﬀ when transporting

or storing.

○ When transporting in a vehicle, cover blade with

blade cover.

If situations occur which are not covered in this

manual, take care and use common sense. Contact

Hitachi Authorized Service Centers if you need

assistance. Pay special attention to statements

preceded by the following words:

WARNING

Indicates a strong possibility of severe

personal injury or loss of life, if instructions

are not followed.

CAUTION

Indicates a possibility of personal injury or

equipment damage, if instructions are not

followed.

NOTE

Helpful information for correct function and use.

CAUTION

Do not disassemble the recoil starter. You

may get a possibility of personal injury with

recoil spring.

WARRANTY

The warranties provided by Hitachi Koki U.S.A., Ltd.

are explained in the warranty card enclosed with this

product titled “Hitachi Outdoor Power Equipment

Limited Warranty”.

Models CG22EAB(SLP) and CG22EAB(L) are NOT

intended for commercial use, and therefore, NO

warranty is provided to their commercial applications

and rental applications. Therefore, the two year

warranty for “the ﬁ rst commercial end user” and one

year warranty for “rental applications” mentioned in

the warranty card are provided on CG22EAS(SLP),

CG22EAS(SL), CG22EAS(S), CG22EAD(SLP) and

CG22EAD(SL), but NOT on CG22EAB(SLP) and

CG22EAB(L).

6

English

SPECIFICATIONS

Model

CG22EAS (SLP)

CG22EAS (SL)

CG22EAS (S)

CG22EAD (SLP)

CG22EAD (SL)

CG22EAB (SLP)

CG22EAB (L)

Engine Size (cu. in.) 1.27 (21.1 ml)

Spark Plug Champion CJ6 or equivalent

Fuel Tank Capacity (ﬂ . oz) 14.9 (0.44 l)

Dry Weight (Ibs) 9.7 (4.4 kg) 10.4 (4.7 kg) 10.4 (4.7 kg)

8.8 (4.0 kg)

8.6 (3.9 kg)

Sound pressure

level LpA (dB (A))

(EN27917)

Equivalent

90 89 91 90 90

Measured sound

power level LwA

(dB (A))

(ISO10884)

Equivalent

104 104 103 104 104

Measured sound

power level LwA

(dB (A))

(2000/14/EC)

Racing

107 107 106 107 107

Guaranteed

sound power

level LwA (dB (A))

(2000/14/EC)

Racing

108 109 108 108 109

Vibration level (m/s

2

)

(ISO7916)

Equivalent (Front / Left handle)

Equivalent (Rear / Right handle)

Idling (Front / Left handle)

Idling (Rear / Right handle)

Racing (Front / Left handle)

Racing (Rear / Right handle)

6.7

4.1

4.9

3.3

8.0

4.7

4.5

4.8

2.7

3.4

5.8

5.9

4.7

4.3

2.7

3.4

6.1

5.1

7.7

4.7

4.1

3.7

10.1

5.5

6.5

6.9

5.3

3.8

7.6

8.9

7

English

Model

CG24EASP (SL) CG24EASP (S) CG27EASP (SL) CG27EASP (S)

Engine Size (cu. in.) 1.46 (23.9 ml) 1.64 (26.9 ml)

Spark Plug Champion CJ6 or equivalent

Fuel Tank Capacity (ﬂ . oz) 18.3 (0.52 l)

Dry Weight (Ibs) 10.1 (4.6 kg) 10.8 (4.9 kg) 10.8 (4.9 kg) 11.2 (5.1 kg)

Sound pressure

level LpA (dB (A))

(EN27917)

Equivalent

92 92 93 93

Measured sound

power level LwA

(dB (A))

(ISO10884)

Equivalent

105 105 107 107

Measured sound

power level LwA

(dB (A))

(2000/14/EC)

Racing

108 108 110 110

Guaranteed

sound power

level LwA (dB (A))

(2000/14/EC)

Racing

111 111 111 111

Vibration level (m/s

2

)

(ISO7916)

Equivalent (Front / Left handle)

Equivalent (Rear / Right handle)

Idling (Front / Left handle)

Idling (Rear / Right handle)

Racing (Front / Left handle)

Racing (Rear / Right handle)

6.2

5.8

4.2

3.1

7.7

7.6

3.7

4.7

2.6

4.4

4.6

5.0

6.2

7.4

3.1

2.0

8.3

10.4

4.8

4.0

2.8

3.9

6.2

4.1

NOTE

Equivalent noise level/vibration level are calculated as the time-weighted energy total for noise/vibration

levels under various working conditions with the following time distribution: 1/2 Idle, 1/2 racing.

* All data subject to change without notice.

8

English

ASSEMBLY PROCEDURES

Drive shaft to engine (Fig. 1)

Loosen tube locking bolt (1) about ten turns so that

the bolt point will not obstruct drive shaft tube to be

inserted. When inserting drive shaft tube, hold the

tube locking bolt outward preventing inside ﬁ tting

from obstructing as well.

Insert the drive shaft into the clutch case of the

engine properly until the marked position (2) on the

drive shaft tube meets the clutch case.

Some models may come with the drive shaft already

installed.

1

2

1

2

Fig. 1

NOTE

When it is hard to insert drive shaft up to the

marked position on the drive shaft tube, turn

drive shaft by the cutter mounting end clockwise

or counter-clockwise. Tighten tube locking bolt

lining up the hole in the shaft tube. Then tighten

clamp bolt securely.

Installation of attachment

1. Join the attachment in place of it.

2. Make sure the lock pin (3) ﬁ ts in the location hole

(4) of tube and that the tube will not come oﬀ .

(Fig. 2)

3. Tighten the knob nut (5) securely. (Fig. 2)

3

5

4

Fig. 2

Installation of handle

WARNING

When you use steel/rigid blades on straight

shaft trimmers or brush cutters, always use

a barrier bar (6) and shoulder harness with

the loop handle. (Fig. 3)

6

Fig. 3

Attach the handle to the drive shaft tube with the

angle towards the engine.

Adjust the location to the most comfortable position

before operation.

NOTE

If your unit has handle location label on drive

shaft tube, follow the illustration.

Remove the handle bracket (7) from the assembly.

(Fig. 4)

Place the handles and attach the handle bracket with

four bolts lightly. Adjust to appropriate position. Then

attach it ﬁ rmly with the bolts.

7

Fig. 4

9

English

Attach the protection tube to the drive shaft or handle

using cord clamps (8). (Fig. 5)

8

Fig. 5

NOTE

If the protection tube is set apart from the handle

or pipe, it will be caught by something during

operation and it may cause serious injury. Do not

set the protection tube apart from the handle or

pipe.

Throttle wire / stop cord

Press the upper tab (9) and open the air cleaner

cover. (Fig. 6)

9

Fig. 6

Connect stop cords. (Fig. 7)

Fig. 7

If the throttle outer end (10) is threaded on your unit,

screw it and the earth terminal (11) (if so equipped)

into the cable adjuster stay (12) all the way, and then

tighten this cable end using the adjuster nut (13)

against the cable adjuster stay (12).

Connect throttle wire end (14) to carburetor (15)

and install swivel cap (16) (if so equipped) where is

included in tool bag, onto swivel (15) (Fig. 8).

Some models may come with the parts installed.

11

12

10

13

14

15

16

Fig. 8

Installation of blade guard (Fig. 9, 10, 10-1, 11)

WARNING

● Do not start or operate unit unless each

guard is properly assembled to unit.

● lf unit is operated without a sharp line

limiters, the line will become too long, the

engine will overheat, and engine damage

may occur.

● Check sharp line limiters surely cut nylon

line when operating.

Fig. 9

Fig. 10 Fig. 10-1

10

English

Fig. 11

NOTE

The guard bracket may come already mounted to

the gear case on some models.

Install the blade guard on drive shaft tube against

angle transmission. Tighten the guard bracket ﬁ rmly

so that the blade guard does not swing or move

down during operation.

Install the blade guard to the guard bracket, which

also secures the guard to the gear case using the

two guard mounting screws.

CAUTION

Some blade guards are equipped with sharp

line limiters. Be careful with handling it.

When using a trimmer head with two piece type

blade guard, attach the guard extension to the blade

guard. (Fig. 12)

Fig. 12

NOTE

○ When attaching the guard extension to the blade

guard, the sharp line limiter must be removed

from the blade guard, (if so installed).

○ If your unit has guard location label on drive shaft

tube, follow the indication.

○ To remove the guard extension, refer to the

drawings. Wear gloves as the extension has a

sharp line limiter, then push the four square tabs

on the guard one by one in order. (Fig. 13)

Fig. 13

Installation of semi-auto cutting head

1. Function

Automatically feeds more nylon cutting line

when it is tapped at low rpm (not greater than

4,500 rpm).

11

English

Speciﬁ cations

Code No.

Type of

attaching

screw

Direction of

rotation

Size of

attaching

screw

6696454

Female

screw

Counterclockwise

M10×P1.25-

LH

6696597

Female

screw

Clockwise

M8×P1.25-

RH

Applicable nylon cord

Cord diameter: 1/8˝ (Φ3.0 mm) Length: 6.5 ft (2 m)

Cord diameter: 3/22˝ (Φ2.4 mm) Length: 13 ft (4 m)

2. Precautions

○ The case must be securely attached to the cover.

○ Check the cover, case and other components for

cracks or other damage.

○ Check the case and button for wear.

If the wear limit mark (17) on the case is no longer

visible or there is a hole in the bottom (18) of the

button, change the new parts immediately. (Fig.

14)

18

17

Fig. 14

○ The cutting head must be securely mounted to

the unit’s gear case.

○ For outstanding performance and reliability,

always use Hitachi nylon cutting line. Never

use wire or other materials that could become a

dangerous projectile.

○ If the cutting head does not feed cutting line

properly, check that the nylon line and all

components are properly installed. Contact

Hitachi Authorized Service Centers if you need

assistance.

3. Installation (Fig. 15)

○ Install cutting head on gear case of grass

trimmers/brush cutters. The mounting nut is

left-hand-threaded. Turn clockwise to loosen/

counterclockwise to tighten.

19

Fig. 15

For curved shaft models, the mounting nut is right-

hand-threaded. Turn counterclockwise to loosen/

clockwise to tighten.

NOTE

○ Since the cutter holder cap is not used here,

keep it for when a metal blade is used, if so

equipped.

○ Insert Allen wrench (19) into the hole of the gear

case in order to lock the cutter holder.

4. Adjusting line length

○ Set the engine speed as low as possible and tap

the head on the ground. The nylon line will be

drawn out about 1-3/16˝ (3 cm) with each tap.

(Fig. 16)

Fig. 16

Also, you can extend the nylon line by hand but

the engine must be completely stopped. (Fig. 17)

Fig. 17

○ Adjust the nylon line to the proper length

of 4-11/32˝–5-1/2˝ (11–14) cm before each

operation.

12

English

Installation of cutting blade (Fig. 18)

(If so equipped)

When installing a cutting blade, make sure that there

are no cracks or any damage in it and that the cutting

edges are facing the correct direction.

23

21

20

22

19

Fig. 18

NOTE

○ When installing cutter holder cap (20), be sure to

set concave side upward.

○ Insert the alien wrench (19) into the hole of the

angle transmission in order to lock the cutter

holder (21). Please note that the cutter ﬁ xing bolt

or nut (22) has left-handed threads, (clockwise to

loosen/ counter-clockwise to tighten). Tighten the

ﬁ xing bolt or nut with the box wrench.

○ If your unit is of a nut securing type and equipped

with a cotter pin, the blade must be retained with

a new pin (23) each time installed. (Fig. 19)

23

Fig. 19

CAUTION

● Before operation, make sure the blade has

been properly installed.

● If your unit is equipped with protection cover

under a cutting blade, check it for wear or

cracks before operation. If any damage or

wear is found, replace it, as it is an article of

consumption.

WARNING

For Hitachi heads, use only ﬂ exible,

non-metallic line recommended by the

manufacturer. Never use wire or wire ropes.

They can break oﬀ and become a dangerous

projectile.

OPERATING PROCEDURES

Fuel (Fig. 20)

Fig. 20

WARNING

● The trimmer is equipped with a two-stroke

engine. Always run the engine on fuel, which

is mixed with oil.

Provide good ventilation, when fueling or

handling fuel.

● Fuel contains highly ﬂ ammable and it is

possible to get the serious personal injury

when inhaling or spilling on your body.

Always pay attention when handling fuel.

Always have good ventilation when handling

fuel inside building.

Fuel

○ Always use branded 89 octane unleaded

gasoline.

○ Use genuine two-cycle oil or use a mix between

25:1 to 50:1, please consult the oil bottle for the

ratio or Hitachi Authorized Service Centers.

○ Only for the state of California at 50:1.

○ If genuine oil is not available, use an anti-oxidant

added quality oil expressly labeled for air-cooled

2-cycle engine use (JASO FC GRADE OIL or

ISO EGC GRADE). Do not use BIA or TCW

(2-stroke water-cooling type) mixed oil.

○ Never use multi-grade oil (10 W/30) or waste oil.

○ Always mix fuel and oil in a separate clean

container.

Always start by ﬁ ling half the amount of fuel, which

is to be used. Then add the whole amount of oil. Mix

(shake) the fuel mixture. Add the remaining amount

of fuel.

Mix (shake) the fuel-mix thoroughly before ﬁ lling the

fuel tank.

13

English

Fueling

WARNING

● Always shut oﬀ the engine before refueling.

● Slowly open the fuel tank, when ﬁ lling up

with fuel, so that possible over-pressure

disappears.

● Tighten the fuel cap carefully, after fueling.

● Always move the trimmer at least 10 ft (3 m)

from the fueling area before starting.

● Always

wash any spilled fuel from clothing

immediately with soap.

● Be sure to check for any fuel leakage after

refueling.

Before fueling, clean the tank cap area carefully,

to ensure that no dirt falls into the tank. Make sure

that the fuel is well mixed by shaking the container,

before fueling.

Starting

CAUTION

Before starting, make sure the cutting

attachment does not touch anything.

1. Set ignition switch (24) to ON position. (Fig. 21,

22)

26

24

Fig. 21

24

Fig. 22

* Push priming bulb (25) several times so that fuel

ﬂ ows through return pipe (39). (Fig. 23)

25

39

Fig. 23

2. Set choke lever (27) to CLOSED position (A).

(Fig. 24)

27

B

A

Fig. 24

3. Pull recoil starter briskly, taking care to keep the

handle in your grasp and not allowing it to snap

back. (Fig. 25)

Fig. 25

14

English

4. When you hear the engine want to start, return

choke lever to RUN position (open) (B). Then pull

recoil starter briskly again.

NOTE

If engine does not start, repeat procedures from

2 to 5.

5. Then allow the engine about 2–3 minutes to warm

up before subjecting it to any load.

Cutting (Fig. 26, 27, 28)

○ When cutting, operate engine at over 6,500 rpm.

Extended time of use at low rpm may wear out

the clutch prematurely.

○ Cut grass from right to left.

○ Cut grass from left to right (only curve shaft

model).

○ Blade thrust may occur when the spinning blade

contacts a solid object in the critical area.

A dangerous reaction may occur causing the

entire unit and operator to be thrust violently. This

reaction is called blade thrust. As a result, the

operator may lose control of the unit which may

cause serious or fatal injury. Blade thrust is more

likely to occur in areas where it is diﬃ cult to see

the material to be cut.

○ Wear the harness as shown in the ﬁ gure (if so

equipped). The blade turns counter-clockwise,

therefore, be advised to operate the unit from

right to left for eﬃ cient cutting. Keep onlookers

out of working area at least 50 ft (15 m).

Fig. 26

Fig. 27

50 ft

(15 m)

Fig. 28

WARNING

If cutting attachment should strike against

stones or other debris, stop the engine and

make sure that the attachment and related

parts are undamaged. When grass or vines

wrap around attachment, stop engine and

attachment and remove them.

Stopping (Fig. 29, 30)

Decrease engine speed and run at an idle for a few

minutes, then turn oﬀ ignition switch (24).

24

26

Fig. 29

15

English

24

Fig. 30

For models with an engine ignition switch, keep the

ignition switch pressed until the engine comes to a

complete stop.

WARNING

A cutting attachment can injure while it

continues to spin after the engine is stopped

or power control is released. When the unit is

turned oﬀ , make sure the cutting attachment

has stopped before the unit is set down.

Semi-auto cutting head

○ When cutting, operate engine at over 6,500 rpm.

Extended time of use at low rpm may wear out

the clutch prematurely.

○ Cut grass from right to left.

○ Cut grass from left to right (only curve shaft

model).

WARNING

A cutting attachment can injure while it

continues to spin after the engine is stopped

or power control is released. When the unit is

turned oﬀ , make sure the cutting attachment

has stopped before the unit is set down.

Automatically feeds more nylon cutting line when it is

tapped at low rpm (not greater than 4,500 rpm).

MAINTENANCE

MAINTENANCE, REPLACEMENT OR REPAIR

OF THE EMISSION CONTROL DEVICES AND

SYSTEMS MAY BE PERFORMED BY ANY NON-

ROAD ENGINE REPAIR ESTABLISHMENT OR

INDIVIDUAL.

Carburetor adjustment (Fig. 31)

Fig. 31

WARNING

● The cutting attachment may be spinning

during carburetor adjustments.

● Never start the engine without the complete

clutch cover and tube assembled! Otherwise

the clutch can come loose and cause

personal injuries.

In the carburetor, fuel is mixed with air. When the

engine is test run at the factory, the carburetor is

basically adjusted. A further adjustment may be

required, according to climate and altitude. The

carburetor has one adjustment possibility:

T = Idle speed adjustment screw.

Idle speed adjustment (T)

Check that the air ﬁ lter is clean. When the idle

speed is correct, the cutting attachment will not

rotate. If adjustment is required, close (clockwise)

the T-screw, with the engine running, until the

cutting attachment starts to rotate. Open (counter-

clockwise) the screw until the cutting attachment

stops. You have reached the correct idle speed

when the engine runs smoothly in all positions well

below the rpm when the cutting attachment starts to

rotate.

If the cutting attachment still rotates after idle speed

adjustment, contact Hitachi Authorized Service

Centers.

NOTE

Standard Idle rpm is 2,800 – 3,200 rpm.

WARNING

When the engine is idling the cutting

attachment must under no circumstances

rotate.

16

English

Air ﬁ lter (Fig. 32)

The air ﬁ lter must be cleaned from dust and dirt in

order to avoid:

○ Carburetor malfunctions

○ Starting problems

○ Engine power reduction

○ Unnecessary wear on the engine parts

○ Abnormal fuel consumption

Clean the air ﬁ lter daily or more often if working in

exceptionally dusty areas.

28

Fig. 32

Cleaning the air ﬁ lter

Open the air ﬁ lter cover and the ﬁ lter (28). Rinse it in

warm soap suds. Check that the ﬁ lter is dry before

reassembly. An air ﬁ lter that has been used for some

time cannot be cleaned completely. Therefore,

it must regularly be replaced with a new one. A

damaged ﬁ lter must always be replaced.

Fuel ﬁ lter (Fig. 33)

Drain all fuel from fuel tank and pull fuel ﬁ lter line

from tank. Pull ﬁ lter element out of holder assembly

and rinse element in warm water with detergent.

Rinse thoroughly until all traces of detergent are

eliminated. Squeeze, do not wring, away excess

water and allow element to air dry.

NOTE

If element is hard due to excessive dirt buildup,

replace it.

Fig. 33

Spark plug (Fig. 34)

The spark plug condition is inﬂ uenced by:

○ An incorrect carburetor setting

○ Wrong fuel mixture (too much oil in the gasoline)

○ A dirty air ﬁ lter

○ Hard running conditions (such as cold weather)

These factors cause deposits on the spark plug

electrodes, which may result in malfunction and

starting diﬃ culties. If the engine is low on power,

diﬃ cult to start or runs poorly at idling speed, always

check the spark plug ﬁ rst. If the spark plug is dirty,

clean it and check the electrode gap. Re-adjust

if necessary. The correct gap is 0.024˝ (0.6 mm).

The spark plug should be replaced after about 100

operation hours or earlier if the electrodes are badly

eroded.

0.024˝

(0.6 mm)

Fig. 34

NOTE

In some areas, local law requires using a resistor

spark plug to suppress ignition signals. If this

machine was originally equipped with resistor

spark plug, use same type of spark plug for

replacement.

Flexible drive shaft (Fig. 35)

Flexible drive shaft should be removed and

lubricated with good quality lithium grease every

20 hours. To remove the ﬂ exible shaft, ﬁ rst remove

screw (29), loosen bolt (30) and remove the gear

case then pull the shaft out of the drive shaft pipe.

Clean the shaft oﬀ and apply a generous coat of

lithium grease to it and insert if back into the drive

shaft pipe, turn it unit it drops into place then install

the gear case, install & tighten screw (29) and screw

(30).

17

English

29

30

Fig. 35

Angle transmission (Fig. 36)

Check angle transmission or angle gear for

grease level about every 50 hours of operation by

removing the grease ﬁ ller plug on the side of angle

transmission.

If no grease can be seen on the ﬂ anks of the gears,

ﬁ ll the transmission with quality lithium based

multipurpose grease up to 3/4. Do not completely ﬁ ll

the transmission.

Fig. 36

Semi-auto cutting head

Nylon line replacement

(1) Remove the case (31) by ﬁ rmly pushing inward

the locking tabs with your thumbs as shown in

Fig. 37.

31

Fig. 37

(2) After removing the case, take out the reel and

discard the remaining line.

(3) Fold the new nylon line unevenly in half as shown

in picture.

Hook the U-shaped end of the nylon line into the

groove (32) on the center partition of the reel.

Wind both halves of the line on the reel in the

same direction, keeping each half of the line on

its own side of the partition. (Fig. 38)

32

4˝ (10 cm)

Fig. 38

(4) Push each line into the stopper holes (33),

leaving the loose ends approx. 4˝ (10 cm) in

length. (Fig. 39)

33

4˝ (10 cm)

Fig. 39

(5) Insert both loose ends of the line through the cord

guide (34) when placing the reel in the case. (Fig.

40)

34

33

Fig. 40

NOTE

When placing a reel in the case, try to line up the

stopper holes (33) with the cord guide (34) for

easier line release later.

18

English

(6) Place the cover over the case so that the cap

locking tabs (35) on the case meet the long holes

(36) on the cover. Then push the case securely

until it clicks into place. (Fig. 41)

35

36

Fig. 41

(7) The initial cutting line length should be approx.

4-11/32˝–5-1/2˝ (11–14 cm) and should be equal

on both sides. (Fig. 42)

4-11/32˝–5-1/2˝

(11-14 cm)

4-11/32˝–5-1/2˝

(11-14 cm)

Fig. 42

Blade (Fig. 43)

WARNING

Wear protective gloves when handling or

performing maintenance on the blade.

37

38

Fig. 43

○ Use a sharp blade. A dull blade is more likely to

snag and thrust. Replace the fastening nut if it is

damaged and hard to tighten.

○ When replacing blade, purchase one

recommended by Hitachi, with a 25.4 mm (one

inch) ﬁ tting hole.

○ When installing a saw blade (38), always face

the stamped side up. In the case of a 3 or 4 tooth

blade (37), it can be used on either side.

○ Use the correct blade for the type of work.

○ When replacing blades, use appropriate tools.

○ When cutting edges become dull, re-sharpen

or ﬁ le as shown in the illustration. Incorrect

sharpening may cause excessive vibration.

○ Discard blades that are bent, warped, cracked,

broken or damaged in any way.

NOTE

When sharpening blade it is important to maintain

an original shape of radius at the base of the

tooth to avoid cracking.

Maintenance schedule

Below you will ﬁ nd some general maintenance

instructions. For further information please contact

Hitachi Authorized Service Centers.

Daily maintenance

○ Clean the exterior of the unit.

○ Check that the harness is undamaged.

○ Check the blade guard for damage or cracks.

Change the guard in case of impacts or cracks.

○ Check that the cutting attachment is properly

centred, sharp, and without cracks. An oﬀ -centre

cutting attachment induces heavy vibrations that

may damage the unit.

○ Check that the cutting attachment nut is

suﬃ ciently tightened.

○ Make sure that the blade transport guard is

undamaged and that it can be securely ﬁ tted.

○ Check that nuts and screws are suﬃ ciently

tightened.

Weekly maintenance

○ Check the starter, especially the cord and return

spring.

○ Clean the exterior of the spark plug.

○ Remove it and check the electrode gap. Adjust it

to 0.024˝ (0.6 mm), or change the spark plug.

○ Check that the angle gear is ﬁ lled with grease up

to 3/4.

○ Clean the air ﬁ lter.

Monthly maintenance

○ Rinse the fuel tank with gasoline.

○ Clean the exterior of the carburetor and the

space around it.

○ Clean the fan and the space around it.

19

Français

SIGNIFICATION DES SYMBOLES

REMARQUE:

Certains appareils n’en sont pas pourvus.

Symboles

ATTENTION

Les symboles suivants sont utilisés pour l’outil. Bien se familiariser avec leur

signiﬁ cation avant d’utiliser l’outil.

Il est essentiel de lire et de comprendre

parfaitement les consignes de sécurité

et autres avertissements suivants.

Vous devez les observer strictement.

L’utilisation inattentive ou inadéquate

de cette machine risque de provoquer

des blessures graves ou fatales.

Au besoin, utilisez des gants, notamment

lors du montage de l’équipement de

coupe.

Lisez attentivement et respectez toutes

les instructions et tous les avertissements

donnés dans ce manuel et sur le produit.

Utilisez des chaussures antidérapantes

et solides.

Utilisez toujours des lunettes de protection

ainsi qu’un casque et des protections

d’oreilles lorsque vous utilisez ce produit.

Une réaction de poussée de la lame peut

survenir lorsque la lame en rotation entre

en contact avec un objet solide dans la

zone critique. Une réaction dangereuse

peut alors survenir, provoquant un

mouvement incontrôlé et violent de

toute la machine et de l’utilisateur.

Cette réaction est appelée rebond.

Elle peut faire perdre le contrôle de la

machine et être à l’origine de blessures

sérieuses, voire fatales. Cette réaction

incontrôlée de la lame risque davantage

de survenir lorsque l’opérateur ne peut

voir le matériau à couper.

N’utilisez pas de lames métalliques/rigides

lorsque ce signe apparaît sur la machine.

Maintenez les enfants, spectateurs et aides

à plus de 50 pieds (15 m) de l’appareil. Si

quelqu’un s’approche de vous, coupez

immédiatemment le moteur et arrêtez

l’outil de coupe.

Indique l’emplacement de la poignée.

Ne positionnez pas la poignée au-

dessus de ce point.

Faites attention aux projections

d’objets.

Indique l’emplacement du protège-

lame pour un coupe-herbe ou une

tête de coupe semi-automatique.

Indique la vitesse maximale de l’arbre.

N’utilisez pas d’outil de coupe dont la

vitesse de rotation (nombre de tours/

minute) est inférieure à la vitesse de

rotation de l’arbre.

Avant l’utilisation de votre nouvelle machine

• Lisez attentivement le manuel d’utilisation.

• Vériﬁ ez que l’équipement de coupe est monté et réglé correctement.

• Démarrez la machine et vériﬁ ez le réglage du carburateur. Voir la section “ENTRETIEN”.

Sommaire

DESCRIPTION ..................................................... 20

PRÉCAUTIONS ET CONSIGNES DE SÉCURITÉ

... 21

GARANTIE ........................................................... 22

CARACTÉRISTIQUES ......................................... 23

MONTAGE ........................................................... 25

UTILISATION ........................................................ 29

ENTRETIEN ......................................................... 32

20

Français

16

17

13

7

6

2

5

4

10

13

11

9

7

6

14

5

4

2

13

11

9

7

15

6

14

5

4

2

13

9

11

7

6

5

4

2

9

11

13

8

7

6

5

14

4

3

12

1

DESCRIPTION

Ce manuel étant commun à plusieurs modèles, vous

constaterez peut-être certaines diﬀ érences entre

les images et votre appareil. Suivez les instructions

relatives à votre modèle.

1. Bouchon du réservoir de carburant

2. Commande des gaz

3. Poignée du lanceur

4. Protège-lame

5. Outil de coupe

6. Tube de transmission

7. Poignée

8. Œillet d’accrochage

9. Interrupteur marche-arrêt

10. Harnais

11. Levier accélérateur bloqué

12. Levier d’étranglement

13. Moteur

14. Boîtier de renvoi d’angle

15. Boîtier de raccordement

16. Clé à douille multiple

17. Mode d’emploi

CG 22EAS (S)

CG 24EASP (S)

CG 27EASP (S)

CG 22EAB (L)

CG 22EAB (SLP)

CG 22EAD (SLP)

CG 22EAD (SL)

CG 22EAS (SLP)

CG 22EAS (SL)

CG 24EASP (SL)

CG 27EASP (SL)

La page charge ...

Hitachi CG 22S Safety Instructions And Instruction Manual

Hitachi CG 22S Safety Instructions And Instruction Manual

dans d''autres langues

Documents connexes

Autres documents